JEEP WRANGLER / JEEP GLADIATOR SIDE DOOR WINDOW...
of 25
/25
Embed Size (px)
Transcript of JEEP WRANGLER / JEEP GLADIATOR SIDE DOOR WINDOW...
1 2
MEDLINE
MEDIUM
70% Isopropyl AlcoholSterile in unopened,
Product is not made withNatural Rubber Latex
STERILE SINGLEREF MDS090735USE ONLY2-PLY PAD
undamaged package
ALCOHOL
1
MEDLINE
MEDIUM
70% Isopropyl AlcoholSterile in unopened,
Product is not made withNatural Rubber Latex
STERILE SINGLEREF MDS090735USE ONLY2-PLY PAD
undamaged package
ALCOHOL
1
3MAutomotive AdhesionPromoter 4298Promoteur d’adhérencePromotor de adhesiónFor plastic trim attachment with 3M™ AcrylicFoam Tapes.
Pour la fixation des garnitures en matièreplastique à 1’aide de ruban en mousseacrylique 3M™.
Para adherir bordes de plástico con cintas deepuma acrílica 3M™.
27°C
15°C
80°F
60°F
3 4 5 6
K6862912ABSWG280
www.mopar.com
August 20 2019
JEEP WRANGLER / JEEP GLADIATORSIDE DOOR WINDOW VISORS
Call Out Description Quantity Part Number
82215372AB
82215368AB
1
4
1
FRONT
1
NON-PERMANENT
1 Front RHS Window Visor12 Front LHS Window Visor
25 Alcohol Wipe
16 3M Primer Wipe
44 Push Pin Rivet
3 Metal Clip
7 Rear RHS Window Visor
8 Rear LHS Window Visor
5 Alcohol Wipe
6 3M Primer Wipe
4 Push Pin Rivet
3 Metal Clip
NOTE: 4-Door Only(right hand & left hand) (right hand & left hand)
REAR FRONT
7 8
MEDLINE
MEDIUM
70% Isopropyl AlcoholSterile in unopened,
Product is not made withNatural Rubber Latex
STERILE SINGLEREF MDS090735USE ONLY2-PLY PAD
undamaged package
ALCOHOL
1
MEDLINE
MEDIUM
70% Isopropyl AlcoholSterile in unopened,
Product is not made withNatural Rubber Latex
STERILE SINGLEREF MDS090735USE ONLY2-PLY PAD
undamaged package
ALCOHOL
1
3MAutomotive AdhesionPromoter 4298Promoteur d’adhérencePromotor de adhesiónFor plastic trim attachment with 3M™ AcrylicFoam Tapes.
Pour la fixation des garnitures en matièreplastique à 1’aide de ruban en mousseacrylique 3M™.
Para adherir bordes de plástico con cintas deepuma acrílica 3M™.
27°C
15°C
80°F
60°F
3 4 5 6
REAR1
4
1
2
1
4
0mm
10
20
30
40
50
60
70
80
90
VEHICLE AND PART
60°F
1.
Clean and dry the upper door areaand lower the front and rear windows.
2.
NOTE:Ensure all surfaces are completely dry.
K6862912ABSWG280
2
August 20 2019
FRONT SET
Trial fit the visors Item (1) or (2) 20mm (0.8”) away from the top edge of the front door frame and 38mm (1.5”) from the rear edge of the door frame.Note the red backing tape attach-ment areas.
Note the top slots on the visor and where they correspond to the door.Remove the front visor
3.
38mm
20mm
DO NOT REMOVE RED TAPE LINER.
20mm 20mm
38mm
Important
Important ALIGN CLIP POSITION WITH HOLES IN VISORBEFORE PUSHING CLIP IN ALL THE WAY IN
3
33
33
DOOR
SEAL
ONLY INSERT HALF WAY
CHECK CLIP HOLES ARE ALIGNED
PUSH AND SNAPIN CLIP
Important
RE-INSTALLSEAL
[A] At the noted clip positions gently pull down the door rubber trim away from the door frame.
[B] Partially install the clips (3) by engaging halfway into the door channel.
[C] Confirm the clips are in the correct location by checking they are aligned with the markings from step 2 and with the slots in the visor as per positioning in step 2.
[D] Once confirmed push clips in all the way into channel.
[E] Push the door rubber back into place and close the window.
A B C D E
1 2
K6862912ABSWG280
3
August 20 2019
6.
5.
4.
Clean the tape attachment areas on the front door frames thoroughly with the alcohol wipes (5) provided, and allow to dry.
Apply adhesion promoter (6) directly onto the tape attachment area.
Allow the Adhesion Promoter 5 minutes drying time once
Important
Avoid overlapping and apply only where tape will be located.
Important
Keep out of contact with eyes, skin etc.
Important
Do not touch the exposed surface of the backing tape.
Important
Peel the red tape liner back approx-imately 50mm (2”) and fold at 45º to the outside of the front visor, as shown. 50mm
50mm
50mm
APPLY TO SHADED TAPE AREA ONLY
ON THE DOOR
20mmMEDLINE
MEDIUM
70% Isopropyl AlcoholSterile in unopened,
Product is not made withNatural Rubber Latex
STERILE SINGLEREF MDS090735USE ONLY2-PLY PAD
undamaged package
ALCOHOL
1
5
Allow to dry.
3MAutomotive AdhesionPromoter 4298Promoteur d’adhérencePromotor de adhesiónFor plastic trim attachment with 3M™ AcrylicFoam Tapes.
Pour la fixation des garnitures en matièreplastique à 1’aide de ruban en mousseacrylique 3M™.
Para adherir bordes de plástico con cintas deepuma acrílica 3M™.
27°C
15°C
80°F
60°F
6
K6862912ABSWG280
4
August 20 2019
7.
8.
9.
Position the front visor on the front door frame following the positioning in Step 2.
Double check the positioning of the visor to the door (step 2), then apply light pressure to the tape areas.
Double check the positioning of the front visor to the metal clips (3).
Peel the remaining backing tape liner away slowly by pulling on the exposed ends of the liner, and apply firm pressure (15 psi min) across the entire adhesive tape area.
Ensure the slots in the visor align with the holes in the metal clips.
Insert the two push pin rivets (4) through the slots in the visor and through the holes in the metal clips.
REPEAT STEPS 1-9 for the opposite side.
A.
Push the pin rivets (4) down to lock them into the visor and clips.
B.
24 HOURS
AFTER INSTALLATION, WINDOWS SHOULD REMAIN FULLY CLOSED FOR 24 HOURS FOR BEST RESULTS.
DO NOT WASH THE VEHICLE IMMEDIATELY (WAIT 1 HOUR MINIMUM)
Important
A B4
1.
2.
K6862912ABSWG280
1
August 20 2019
REAR SET - 4 DOOR ONLY
3.
Clean the tape attachment areas on the rear door frames thoroughly with the alcohol wipes (5) provided, and allow to dry.
Trial fit the visor Item (7) or (8) 20mm (0.8”) away from the top edge of the rear door frame and 38mm (1.5”) from the front edge of the door frame.Note the red backing tape attach-ment areas.
Note the top slots on the visor and where they correspond to the door.Remove the rear visor
DO NOT REMOVE RED TAPE LINER
38mm20mm 20mm
20mmMEDLINE
MEDIUM
70% Isopropyl AlcoholSterile in unopened,
Product is not made withNatural Rubber Latex
STERILE SINGLEREF MDS090735USE ONLY2-PLY PAD
undamaged package
ALCOHOL
1
5
Important
3
33
33
DOOR
SEAL
ONLY INSERT HALF WAY
CHECK CLIP HOLES ARE ALIGNED
PUSH AND SNAPIN CLIP
Important
RE-INSTALLSEAL
A B C D E
Important ALIGN CLIP POSITION WITH HOLES IN VISOR BEFORE
PUSHING CLIP IN ALL THE WAY IN
[A] At the noted clip positions gently pull down the door rubber trim away from the door frame.
[B] Partially install the clips (3) by engaging halfway into the door channel.
[C] Confirm the clips are in the correct location by checking they are aligned with the markings from step 2 and with the slots in the visor as per positioning in step 2.
[D] Once confirmed push clips in all the way into channel.
[E] Push the door rubber back into place and close the window.
87
K6862912ABSWG280
2
August 20 2019
5.
Do not touch the exposed surface of the backing tape.
Important
50mm 50mm
50mm
6.
Position the rear visor on the rear door frame following the positioning in (Step 1).
Double check the positioning of the visor to the door (Step 1), then apply light pressure to the tape areas.
Peel the red tape liner back approx-imately 50mm (2”) and fold at 45º to the outside of the front visor, as shown.
3MAutomotive AdhesionPromoter 4298Promoteur d’adhérencePromotor de adhesiónFor plastic trim attachment with 3M™ AcrylicFoam Tapes.
Pour la fixation des garnitures en matièreplastique à 1’aide de ruban en mousseacrylique 3M™.
Para adherir bordes de plástico con cintas deepuma acrílica 3M™.
27°C
15°C
80°F
60°F
6
APPLY TO SHADED TAPE AREA ONLY
ON THE DOOR
4. Apply adhesion promoter (6) directly onto the tape attachment area.
Allow the Adhesion Promoter 5 minutes drying time once
Important
Avoid overlapping and apply only where tape will be located.
Important
Keep out of contact with eyes, skin etc.
Important
Allow to dry.
K6862912ABSWG280
3
August 20 2019
7. Double check the positioning of the rear visor to the metal clips (3).
Peel the remaining backing tape liner away slowly by pulling on the exposed ends of the liner, and apply firm pressure (15 psi min) across the entire adhesive tape area.
Ensure the slots in the visor align with the holes in the metal clips.
8.
Insert the two push pin rivets (4) through the slots in the visor and through the holes in the metal clips.
REPEAT STEPS 1-8 for the opposite side.
A.
Push the pin rivets (4) down to lock them into the visor and clips.
B.
24 HOURS
AFTER INSTALLATION, WINDOWS SHOULD REMAIN FULLY CLOSED FOR 24 HOURS FOR BEST RESULTS.
DO NOT WASH THE VEHICLE IMMEDIATELY (WAIT 1 HOUR MINIMUM)
Important
A B4
