JD 7K 1700 WheelScrapers
2
SCHAFFERT MFG. CO. INC. - phone: 800-382-2607 - fax: 308-364-2410 71495 rd. 397 - indianola, ne 69034 - phone: 800-382-2607 - fax: 308-364-2410 - [email protected] - www.schaffert.com - Setp 18,2009 GAUGE AND PRESS WHEEL SCRAPER MOUNTING INSTRUCTIONS John Deere 7000-1700, Kinze, and White Planters (Read Instructions Completely before Beginning Installation) Before working on your planter or drill DANGER: when storing or working on the planter always install cylinder stops or place the planter on stands to prevent personal injury or damage to the attachments. Press Wheel Mounting Instructions Before you begin, verify the “package contents” to ensure all items are included. Step #1: The press wheel scrapers (fig. (a), (b), & (c)) are mounted with a 1/2” bolt in an existing hole on the top of the press wheel frame towards the front of JD 7000, 7100 and Kinze planters (fig. (c)). On newer models of the JD 7200 and 7300 planters a 1/2” hole needs to be drilled 1 1/2” back from the front and in the middle of the press wheel frame. Assemble a scraper & lay on press wheel frame to mark where hole needs to be drilled. Step #2: Attach the scraper bracket with a 1/2” bolt. Adjust left and right scrapers so the half moon notches fit over the press tire leaving enough clearance so the tire does not drag. (fig. (a) & (b)). Tighten the 1/4” nuts. NOTE: Clean old residue and dried mud each day before starting to plant to prevent wheel drag. Gauge Wheel Mounting Instructions Before you begin, verify the “package contents” to ensure all items are included. Step #1: Remove gauge wheel and arm from the planter and clamp in a shop vise so the grease zerk is up and exposed for welding. NOTE: If you have the new style gauge arms that have O rings inside the gauge arm mount, before welding the four-sided key stock put a wet towel in each end of the holes of the arm so you do not melt the O rings. Weld a little on each arm which will avoid over heating and burning of O rings or take out O rings before welding. Step #2: Place gauge wheel scraper blade centered between the outside edges of the gauge wheel, 1/2” below the grease zerk on the gauge wheel arm. (fig. (d)) Check again to see if the wheel scraper blade is cen- tered. Then weld all four sides of the square stock. Remove grease zerk from first arm welded and use it in all other units. This will save replacing all grease zerks after welding next to them and also protect grease zerk threads. NOTE: NOTE: use a 1/8” 60 or 70 series stick rod with the welder set at 130- 150 AMP AC or DC or .030-.035 wire welder with gas or flux core. Have ample ventilation while welding to avoid breathing fumes. Step #4: Adjust scraper blade on each wheel so it misses the gauge tire and lets it turn freely. Tighten the 1/2” bolt (fig. (e)). Place the gauge wheel back on the planter making sure to replace the spacer washers where needed for proper clearance of the disc. fig. (a) fig. (b) fig. (c) gauge wheel scrapers press wheel scrapers JD 7000, 7100, 7200, 7300 & Kinze models White 6000 & 8000 series from behind the planter fig. (d) fig. (e) zerk hole press wheel scrapers installed gauge wheel scrapers installed Gauge Wheel Package Contents (for one row) Item Quantity Metal Bracket .................... 2 1/2” x 1” bolt ................... 2 Lock Washer ..................... 2 Plastic Scraper ................... 2 1/4 “ X 1” bolts .................. 4 Whiz nuts ....................... 4 Angle Cut Sq. Key stock ............ 2 Instruction Sheet ................. 1 Press Wheel Package Contents (per single row) Item Quantity Metal Scraper .................... 2 Whiz Nuts ....................... 2 Main Bracket .................... 1 1/2” x 1” bolt ................... 1 Lock Washer ..................... 1 Nut ............................ 1 Instruction Sheet ................. 1
-
Upload
richard-baker -
Category
Documents
-
view
216 -
download
0
description
JD 7K 1700 WheelScrapers
Transcript of JD 7K 1700 WheelScrapers
-
SCHAFFERT MFG. CO. INC. - phone: 800-382-2607 - fax: 308-364-2410
71495 rd. 397 - indianola, ne 69034 - phone: 800-382-2607 - fax: 308-364-2410 - [email protected] - www.schaffert.com - Setp 18,2009
GAUGE AND PRESS WHEEL SCRAPER MOUNTING INSTRUCTIONS
John Deere 7000-1700, Kinze, and White Planters(Read Instructions Completely before Beginning Installation)
Before working on your planter or drillDANGER: when storing or working on the planter always install cylinder stops or place the planter on stands to prevent personal injury or damage to theattachments.
Press Wheel Mounting InstructionsBefore you begin, verify the package contents to ensure all items are included.
Step #1: The press wheel scrapers (fig. (a), (b), & (c)) are mounted with a 1/2bolt in an existing hole on the top of the press wheel frame towards thefront of JD 7000, 7100 and Kinze planters (fig. (c)). On newer models ofthe JD 7200 and 7300 planters a 1/2 hole needs to be drilled 1 1/2back from the front and in the middle of the press wheel frame. Assemblea scraper & lay on press wheel frame to mark where hole needs to bedrilled.
Step #2: Attach the scraper bracket with a 1/2 bolt. Adjust left and right scrapers sothe half moon notches fit over the press tire leaving enough clearance so thetire does not drag. (fig. (a) & (b)). Tighten the 1/4 nuts. NOTE: Clean oldresidue and dried mud each day before starting to plant to prevent wheel drag.
Gauge Wheel Mounting InstructionsBefore you begin, verify the package contents to ensure all items are included.
Step #1: Remove gauge wheel and arm from the planter and clamp in a shop vise sothe grease zerk is up and exposed for welding. NOTE: If you have the newstyle gauge arms that have O rings inside the gauge arm mount, beforewelding the four-sided key stock put a wet towel in each end of the holes ofthe arm so you do not melt the O rings. Weld a little on each arm whichwill avoid over heating and burning of O rings or take out O rings beforewelding.
Step #2: Place gauge wheel scraper blade centered between the outside edgesof the gauge wheel, 1/2 below the grease zerk on the gauge wheelarm. (fig. (d)) Check again to see if the wheel scraper blade is cen-tered. Then weld all four sides of the square stock. Removegrease zerk from first arm welded and use it in all other units. Thiswill save replacing all grease zerks after welding next to them andalso protect grease zerk threads.
NOTE: NOTE: use a 1/8 60 or 70 series stick rod with the welder set at 130-150 AMP AC or DC or .030-.035 wire welder with gas or flux core.Have ample ventilation while welding toavoid breathing fumes.
Step #4: Adjust scraper blade on each wheel so itmisses the gauge tire and lets it turnfreely. Tighten the 1/2 bolt (fig. (e)).Place the gauge wheel back on the plantermaking sure to replace the spacer washerswhere needed for proper clearance of thedisc.
fig. (a) fig. (b)fig. (c)
gauge wheel scrapers
press wheel scrapers
JD 7000, 7100, 7200, 7300 & Kinze models
White 6000 & 8000 series frombehind the planter
fig. (d)
fig. (e)
zerk hole
press wheelscrapers installed
gauge wheelscrapersinstalled
Gauge Wheel Package Contents(for one row)
Item QuantityMetal Bracket. . . . . . . . . . . . . . . . . . . . 21/2 x 1 bolt . . . . . . . . . . . . . . . . . . . 2Lock Washer . . . . . . . . . . . . . . . . . . . . . 2Plastic Scraper . . . . . . . . . . . . . . . . . . . 21/4 X 1 bolts . . . . . . . . . . . . . . . . . . 4Whiz nuts . . . . . . . . . . . . . . . . . . . . . . . 4Angle Cut Sq. Key stock . . . . . . . . . . . . 2Instruction Sheet . . . . . . . . . . . . . . . . . 1
Press Wheel Package Contents(per single row)
Item QuantityMetal Scraper. . . . . . . . . . . . . . . . . . . . 2Whiz Nuts . . . . . . . . . . . . . . . . . . . . . . . 2Main Bracket . . . . . . . . . . . . . . . . . . . . 11/2 x 1 bolt . . . . . . . . . . . . . . . . . . . 1Lock Washer . . . . . . . . . . . . . . . . . . . . . 1Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Instruction Sheet . . . . . . . . . . . . . . . . . 1
-
SCHAFFERT MFG. CO. INC. - phone: 800-382-2607 - fax: 308-364-2410
71495 rd. 397 - indianola, ne 69034 - phone: 800-382-2607 - fax: 308-364-2410 - [email protected] - www.schaffert.com - Setp 18,2009
GAUGE AND PRESS WHEEL SCRAPERS
ADVANTAGES OF USINGWHEEL SCRAPERS:
- Keeps the gauge wheel clean even in loose,
muddy soil
- Readily adaptable on most planters
- Keeps gauge wheel clean so seed depth does
not change
- Easily flips out of the way when not needed
- Adjustable Gauge Wheel plastic scraper fits
contour of tire
- Welds or bolts on easily
- Affordable & Economical
- Scrapers are made of high molecular poly
which is gentle on wheels and extremely
durable
- Scrapers are adjustable in and out - up and
down to fit any contour
No Hand Cleaning = More Planting
ABOUT THE WHEEL SCRAPERSThe Gauge and Press Wheel Scraper consists ofan adjustable poly blade or a metal blade (forJD press wheel scrapers) that keeps the depthwheel clean and mud-free allowing you to keepan even and consistent seed depth. Mud buildup can lead to shallow plantings, delayed emer-gence and overall reduction in yield. With theGauge and Press Wheel Scraper you will beable to spend more time on the tractor with notime cleaning your depth wheel. No down timecleaning the wheels equals more acres plantedper day. The Gauge Wheel Scraper easily weldsor bolts onto most planters and once the WheelScraper is installed, with a one wrench design,it will conveniently flip out of the way whenyou are not using it.
Gauge Wheel Scrapersfor JD, Kinze, and White Planters
Press Wheel Scrapers for JD & Kinze PlantersDo not have Poly Scrapers - they are metal only.
Without GaugeWheel Scrapers
With GaugeWheel Scrapers
![specservice-tula.ruOM Eng] PW160-7K... · PW160-7K SERIAL NUMBER PW160-7K - K40001 and up WHEELED EXCAVATOR Unsafe use of this machine may cause serious injury or death. Operators](https://static.fdocuments.us/doc/165x107/5e5c712d4cddf94ac92e2479/specservice-tularu-om-eng-pw160-7k-pw160-7k-serial-number-pw160-7k-k40001.jpg)
