J2 Stock Decal Instructions 0 - vcshobbies.com · Computer / Circuitry Wall INTRODUCTION Thank you...
2
49 Piloting Station Communications Station Computer / Circuitry Wall INTRODUCTION Thank you for purchasing ParaGrafix’s decal set for the Moebius Models 1:35 scale Jupiter 2 kit. These decals, expertly printed by JT Graphics (jt-graphics.com), eliminate the need to paint all of the buttons, switches, and display screens located throughout the interior. There are notes indicating those areas where raised kit detail should be knocked down or reduced in height to allow the decals to fit better. You can ignore these notations if you wish, but there will be some wrinkling, misalignment, or other problem. This may be done in whatever way you are most comfortable: sanding, filing, chiseling. These areas are denoted by this symbol: You may also find it easier to cut some decals into sections to make placing them easier. The installation order is entirely up to you. For best results, paint and apply decals before assembling the interior. A setting solution (e.g.. Micro Sol) will help the decals conform to the kit. Please read JT Graphics’ decal instructions on the back page. Raised Detail Installation Parts Order JUPITER 2 JUPITER 2 Decals for Stock Interior ParaGrafix Modeling Systems Kit part (plastic): Decal: Key 1 1 4 Left & Right Consoles 10 Center Console 37 28 x3 3 9 14 15 89 16a 16b 13 Knock down the high points of this part - tape reels, center blocks below reels, buttons on lower console. 24 19 18 1 45 2 11 8 5 or Instructions: PGX122 V1.0
Transcript of J2 Stock Decal Instructions 0 - vcshobbies.com · Computer / Circuitry Wall INTRODUCTION Thank you...
49
Piloting Station Communications Station
Computer / Circuitry Wall
INTRODUCTIONThank you for purchasing ParaGrafix’s decal set for the Moebius Models 1:35 scale Jupiter 2 kit. These decals, expertly
printed by JT Graphics (jt-graphics.com), eliminate the need to paint all of the buttons, switches, and display screens located
throughout the interior.
There are notes indicating those areas where raised kit detail should be knocked down or reduced in height to allow the decals to fit better.
You can ignore these notations if you wish, but there will be some wrinkling, misalignment, or other problem. This may be done in whatever
way you are most comfortable: sanding, filing, chiseling. These areas are denoted by this symbol:
You may also find it easier to cut some decals into sections to make placing them easier.
The installation order is entirely up to you. For best results, paint and apply decals before assembling the
interior. A setting solution (e.g.. Micro Sol) will help the decals conform to the kit.
Please read JT Graphics’ decal instructions on the back page.
Raised Detail
Installation Parts Order
JUPITER 2JUPITER 2Decals for Stock Interior ParaGrafix
Modeling Systems
Kit part (plastic):
Decal:
Key1
1
4 Left & Right Consoles 10 Center Console
37
28x3
39
14
15
89
16a
16b
13
Knock down
the high
points of this
part - tape reels,
center blocks
below reels,
buttons on lower
console.
241918
1
45
2
11 8
5
or
Instructions: PGX122 V1.0
Elevator Controls
75
25
Freezing Tube Walls Repeat Three Times
15
2625
20
Ladder Wall
48
84
7
Piloting / Astrogation
7921
22
Airlock Controls
59Remove the
right-hand
bank of
buttons so that the
decal will fit better.
12
Pod Access Wall126
76
50
ParaGrafixModeling Systems
148 Rocklawn Ave.
Attleboro MA 02703 USA
+1 508-431-9800
www.ParaGrafix.biz
Thank you to Frank Winspur and DaveMetzner of Moebius Models for makingsuch a great kit, for their help andencouragement during the developmentof this add-on set, and for providing atest shot of the kit prior to its release.
“Lost in Space”® is © Space Productions, Inc . Licensed by Synthesis Entertainment.All Rights Reserved.“The Fantasy Worlds of IrwinAllen”® is a registered trademark of Synthesis Entertainment.All Rights Reserved.MoebiusParaGrafix™ and PGMS™ are TM Paul H. Bodensiek.All Rights Reserved.
® is a registered trademark of Moebius Models.
THE FANTASY WORLDS
OF I R W I N ALLEN
17
56
Add your choice of displays on the astrogation station.
Note that the piloting controls “wedge” does not have a
display.
