J-H. Jin1, S-H. Jung , J-H. Moon , J-G. Park · 2017-04-27 · J-H. Jin1, S-H. Jung2, J-H. Moon2,...
18
J-H. Jin 1 , S-H. Jung 2 , J-H. Moon 2 , J-G. Park 2 1 GammaTech Inc. 2 Korea Atomic Energy Research Institute
Transcript of J-H. Jin1, S-H. Jung , J-H. Moon , J-G. Park · 2017-04-27 · J-H. Jin1, S-H. Jung2, J-H. Moon2,...
J-H. Jin1, S-H. Jung2, J-H. Moon2, J-G. Park2 1GammaTech Inc. 2Korea Atomic Energy Research Institute
Gamma Column Scan
Manual Gamma Scanning
Gamma Scanning using Winches
Difficult to install
- 4 guide cables
- Radiation exposure
Difficult to scan
- Long work time
- At least 3 persons
Not accurate positions
- Poor leveling
- Poor reproducibility
Problems in using manual or winch type scanner
Auto
matic G
am
ma C
olu
mn S
canner
• Simplification of cables (7 2 cables)
– By employing tensioning tools Removed the 4 guide cables
– By using signal cable in holding the detector and
– by employing an encoder Removed the measuring tape
• Computer controlled operation (3~5 0~1 person)
– By employing step motor – encoder system
– By incorporating a radiation counter in the scanner
– By logging position-counts data automatically
Main Idea for the Development of Automatic Gamma Column Scanner
• Easy and quick installation
• Only observation during scanning
Graphic results of the scan
Movement of S&D
• Accurate control of S&D positions
Reproducibility and Reliability
Very easy to repeat scanning
• Less radiation exposure
Advantage of the Automation
Improvements of the 4th Automatic Column Scanner
Hardware
- BGO detector, MCA
- Encoder calibration tool
- Simplified operators
- 2 control boxes, LAN
Software program
- LabView
- Encoder calibration method
- Graphic display with a drawing
- Smooth start and stop
- Emergency stops
- Gamma energy spectrum
Radiation detection system
• Scintillation detector
– 1”x1” BGO
• Electric circuit in Detector holder
– High voltage generator
– Counter
– Multichannel analyzer (MCA)
– Communication
• Coaxial wire cable
– Power supply (5 volt)
– Data communication
Smooth movement of source & detector
Installation of Automatic Gamma Column Scanner
① 1 person clime up on top and Lower a rope
② 1 person on the ground connects the rope to a pulley
Installation of Automatic Gamma Column Scanner
③ Raise the pulley to the top
④ Connect the puller to a rod and Fix the rod to the column
Installation of Automatic Gamma Column Scanner
⑤ Repeat ~ with the other side
⑥ Move up source and detector to a leveled position
⑦ Attach tensioners to source and detector
Encoder calibration
MCA
Auto Scan
![j - georgievsk.ruM l \ _ j ` ^: A Z f _ k l b l _ e v ^ f b g b k l j Z p b b = _ h j ] b _ \ k d h ] h h j h ^ k d h ] h j m K l Z \ j h i h e v k d h ] h d j Z y](https://static.fdocuments.us/doc/165x107/603f735da7cb707fbb21f9c6/j-m-l-j-a-z-f-k-l-b-l-e-v-f-b-g-b-k-l-j-z-p-b-b-h-j-b-.jpg)
![H H H I j h ] j Z f f b j m f u d h g l j h e e j u S7-300tekhar.com/.../PDF_all/NEW/05_S7_300_2015_ru-part2.pdf · 2015-05-11 · I j h ] j Z f f b j m _ f u _ d h g l j h e e _](https://static.fdocuments.us/doc/165x107/5f7d5267950a9d27cc5fecac/h-h-h-i-j-h-j-z-f-f-b-j-m-f-u-d-h-g-l-j-h-e-e-j-u-s7-2015-05-11-i-j-h-j-z.jpg)
