Itemized Specifications for the Kitchen Equipment’s · Itemized Specifications for the Kitchen...

42
THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016 Itemized Specifications for the Kitchen Equipment’s Item No.1.01 WASTE BIN TROLLY BIN Qty 04 Tube size 450mm or 600mm as per site MS Construction Powder coated finish 2nos. ultra violet tubes of Philips make Item No.1.02 WALL CLOCK Qty 01 ANY STANDARD BRAND Item No.1.03 EMERGENCY LIGHT Qty 02 Wall mounted Chargeable Batteries Fully Automatic Operation Fluorescent Light Make: Any standard Brand LOCATION AS PER MEP DRAWINGS

Transcript of Itemized Specifications for the Kitchen Equipment’s · Itemized Specifications for the Kitchen...

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Itemized Specifications for the Kitchen Equipment’s Item No.1.01 WASTE BIN TROLLY BIN

Qty 04

Tube size 450mm or 600mm as per site

MS Construction

Powder coated finish

2nos. ultra violet tubes of Philips make

Item No.1.02 WALL CLOCK

Qty 01

ANY STANDARD BRAND

Item No.1.03 EMERGENCY LIGHT

Qty 02

Wall mounted

Chargeable Batteries

Fully Automatic Operation

Fluorescent Light

Make: Any standard Brand

LOCATION AS PER MEP DRAWINGS

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.1.04 FIRST AID BOX

Qty 01

STANDARD

Item No.1.05 SOAP DISPENSER

Qty 01

SS construction

Heavy duty pump

600 ml capacity

Suitable for 23x20cm paper size.

Item No.1.06 PAPER TOWEL DISPENSER

Qty 01

SS construction

Wall mounted

Suitable for wall mounting

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.01 STOCK POT STOVE Qty 2 SIZE 600mm Wide (Verify) x 600 mm deep x 850 mm High to work top on the feet. FRAMEWORK 50 mm x 50 mm x 3mm thick fully welded boxed S.S. angles. BODY CLADDING #18 GA. S.S. on all sides provides louvers at rear for ventilation. TOP #14GA. S.S top to protrude from body by 50 mm, top front turned down 50mm & in 12mm, rear & left turned up 253mm, returned 25mm & down 12mm, Right turned up 102mm, returned 25mm & down 12mm. Top to be secured to framework w/ concealed nuts. Cut out to receive grate as shown in the layout. Work top to overhang the base body by 50mm from front and 75mm at rear. BURNERS High pressure, rated @ 70,000 BTU's/HR. Individual pilots and Controls. 5.0 PSI high pressure “united” make or approved equal. GRATINGS. 600 mm x 600 mm cast iron removable heavy duty Positioned 25 mm above worktop. Positioned as shown in the layout. LEGS. S.S 38mmx38mmx 16 GA. Square pipe legs, Stainless Steel square pipe cross bracing on all sides, gas pipe entry from the rear bottom left. MISC. Provide # 20 GA. S.S. slide out drip trays below the burner With all sides turned-up ¾” & hemmed on outside with formed handles.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.02 PAN HANGER WALL MOUNTED

Qty 01

Overall size: L1200 x W200 . CONSTRUCTION: # 25x25x16swg s.s. square pipe frame as per GN pan size. BRACKETS: # 25x25x16swg s.s. square pipe brackets MOUNTING HEIGHT: 1400 mm AFF and clear 25mm away from the wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.03 EXHAUST HOOD (DOUBLE SKINNED)

Qty 01

SIZE OF BODY: L3700 x W750+300 x H500 (In mm) BODY # 18 GA. Pre polished plastic coated S.S. fully welded body construction, hood. Sloping front construction 300mm (double skinned) front face with front edge at 2100mm above finished floor. Suitable for wall mounting. GREASE FILTERS: Removable 18 GA.S.S. "V" section, measuring 510*510*50 mm thick, full compliment to be furnished. Set at an angle of 45 deg. in full-length w/bottom of filters set in continuous channel. Grease gutter on center & sides. Four (4) no. S.S. grease collecting drawers. Size and nos. of duct collars for exhaust as per HVAC consultants. LIGHTS. Bulkhead lights, diffusing glass, wiring in heat proof conduits, 100 watts each, 220V-50C-1Phase. MISCELLANEOUS Built in equal sections, w/ continuous plenum and field joints for bolting at the site. Suspended from ceiling in both fronts w/ hanger rods & provided with turn buckles, electrical junction box. Hood plenum top shall be closed with # 18 GA S.S. sheets and provided with 75mm high duct collar flange connections, for making connection to exhaust duct. FIRE SUPRESSION Unit shall be provided with water fog sprinkler system fusible links & w/ sprinkler sensor heads located below the filter assembly, complete w/ controls, piping & sensors, supply of fusible links sprinklers, piping and controls by other agency, hood supplier to provide cutouts & clamps to support the fire suppression system, fusible links to get activated at 350 deg. Fire suppression by fire safety contractor.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.04 WORK TABLE WITH UNDERSHELF

Qty 01

Over all size L700xW600x850mm+150MM high Back splash on the rear side.

Top in 16swg s.s. sheet bent 50mm and 12mm on all sides excepting sides with splash

back.

Top sound dampened by an approved method.

Sides splash raised 150mm above the working height of 850mm bent 25mm at 90 deg, and down 12mm.

Top reinforced by 12/25x100x25/12mm channels of 18swg SS sheet.

Uprights in 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar

Item No.2.05 SALAMANDER WITH WALL MOUNTED

FITTINGS

Qty 01

BRAND: ROLLER GRILL OR ANY STANDARD BRAND

MODEL: SALE 04

Adjustable top

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.06 GRIDDLE PLATE (HOT PLATE)

Qty 01

Overall size: L900xW600xH850 + 50 Top:12 mm thick polished MS plate as griddle plate Sides: Side covering of 12” of 20 swg. s.s. sheet Legs:38 mm dia. s.s. pipe with s.s. adjusters Frame: M.S. angle frame of 30x30x3 Trough:25mm wide drain trough to be provided in front & a collection box to be provided under the hole for the drain Burner: Three nos. V type burners with pilot & control valves Under shelf: Made of 18 swg. SS sheet turned down 38mm & in 12 mm Under shelf frame: Under shelf to be secured to MS angle frame of 30x30x3 Item No.2.07 PAN HANGER WALL MOUNTED

Qty 01

Overall size: L900 x W200 . CONSTRUCTION: # 25x25x16swg s.s. square pipe frame as per GN pan size. BRACKETS: # 25x25x16swg s.s. square pipe brackets MOUNTING HEIGHT: 1400 mm AFF and clear 25mm away from the wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.08 DEEP FAT FRYER (DOUBLE)

Qty 01

Over all Size: L600 x W600 x H850mm

Top in 16swg thick s.s. sheet with marine bends, bent 50mm and 12mm on all sides

excepting sides with splash back

Front in 18swg with recessed design s.s. sheet

Sides / back in 20swg thick prepolished s.s. sheet

Frying pan of size 180x400x235mm of each chamber

Frying pan sunk in by 25mm

Deep cold zone

20mm ball valve for quick drying.

Glass wool insulation.

S.S. wire mesh bracket with plastic coated handle.

Swing out type heating element 3 kw single phase 220V.

50-300 deg.C ANCO or EGO-Germany make temperature controller

Kaycee make rotary switch

L & T Vaishno make induction light

Teflon insulated wiring

3 core main lead with socket

Recessed controls

Uprights 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar with minimum height adjustment of +20mm

Framework shall be of 38x38x3mm MS angles with grey hammer tone finish.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.09 PASTA BOILER

Qty 01

SIZE – 12”X24”X34” TOP & WATER TANK MADE OF 16SWG S.S. SHEET OF 304 GRADE. LEGS / VERTICAL MADE OF 40X40X1.6MM SQUARE PIPE. ONE UNDERSHELF OF 18SWG S.S. SHEET.. UNIT WILL HAVE 3NOS. BASKETS WITH INSULATED HANDLE MADE OF S.S. WIRE MESH (APPROX. SIZE 6” DIA & 6” HT.). PROVISION FOR HOLDING OF BASKET ON TOP. TOP WILL BE FITTED WITH WATER TAP. TANK WILL BE FITTED WITH HEATING ELEMENT OF 1.5KW WITH TEMPERATURE CONTROLLER & DRAIN VALVE.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.10 TWO BURNER COOKING RANGE

Qty 01

SIZE: 450 Wide x 900 deep x 850mm High to work top on feet. FRAMEWORK: 40 x 40 x 3mm thick fully welded boxed S.S. angles BODY CLADDING: 1.2mm thick. S.S. on all sides, provided louvers at rear for ventilation. TOP: 1.6mm thick. S.S top to protrude from the body by 50mm, front and both sides turned down 50mm & in 12mm, rear turned up 150mm, returned 25mm & down 12mm.Top to be secured to framework w/ concealed nuts. Cut out to receive two (2) grates as shown in the layout. Work top to over hang the base body by 75mm at rear. BURNERS: Three (3) high pressures, rated @ 70,000 BTU's/hr. Individual pilots and controls. 5.0 PSI high pressure “United” make or approved equal. GRATINGS Three 400x400mm cast iron removable heavy duty positioned 25mm above worktop. Positioned as shown in the layout. LEGS: Four (4) Nos. S.S, 40mm Dia x 1.6mm thick. Tubular pipe legs with S.S. adjustable bullet feet, S.S. tubular pipe cross bracing on all sides, & provided with 18 GA S.S. bottom shelves, gas pipe entry from the rear bottom left. MANIFOLD Common for all burners/ pilots. MISC. Provide 20 g. S.S. slide out drip trays three (1) No. below burners with all sides turned-up 19mm & hemmed on outside with formed handles.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.11 WORK TABLE TWO UNDERSHELF

Qty 01

Over all size L450Xw900x850mm+150MM high Back splash on the rear side.

Top in 16swg s.s. sheet bent 50mm and 12mm on all sides excepting sides with splash

back.

Top sound dampened by an approved method.

Sides splash raised 150mm above the working height of 850mm bent 25mm at 90 deg, and down 12mm.

Top reinforced by 12/25x100x25/12mm channels of 18swg SS sheet.

Uprights in 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.12 PAN HANGER WALL MOUNTED

Qty 01

Overall size: L1800 x W200 . CONSTRUCTION: # 25x25x16swg s.s. square pipe frame as per GN pan size. BRACKETS: # 25x25x16swg s.s. square pipe brackets MOUNTING HEIGHT: 1400 mm AFF and clear 25mm away from the wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.13 FOUR BURNER COOKING RANGE

Qty 01

SIZE: L900 x W900 x 850mm High to work top on feet. FRAMEWORK: 40 x 40 x 3mm thick fully welded boxed S.S. angles BODY CLADDING: 1.2mm thick. S.S. on all sides, provided louvers at rear for ventilation. TOP: 1.6mm thick. S.S top to protrude from the body by 50mm, front and both sides turned down 50mm & in 12mm, rear turned up 150mm, returned 25mm & down 12mm.Top to be secured to framework w/ concealed nuts. Cut out to receive two (2) grates as shown in the layout. Work top to over hang the base body by 75mm at rear. BURNERS: Three (3) high pressures, rated @ 70,000 BTU's/hr. Individual pilots and controls. 5.0 PSI high pressure “United” make or approved equal. GRATINGS Three 400x400mm cast iron removable heavy duty positioned 25mm above worktop. Positioned as shown in the layout. LEGS: Four (4) Nos. S.S, 40mm Dia x 1.6mm thick. Tubular pipe legs with S.S. adjustable bullet feet, S.S. tubular pipe cross bracing on all sides, & provided with 18 GA S.S. bottom shelves, gas pipe entry from the rear bottom left. MANIFOLD Common for all burners/ pilots. MISC. Provide 20 g. S.S. slide out drip trays three (1) No. below burners with all sides turned-up 19mm & hemmed on outside with formed handles.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.14 EXHAUST HOOD (DOUBLE SKINNED)

Qty 01

SIZE OF BODY: L1900 x W1000+300 x H500 (In mm) BODY # 18 GA. Pre polished plastic coated S.S. fully welded body construction, hood. Sloping front construction 300mm (double skinned) front face with front edge at 2100mm above finished floor. Suitable for wall mounting. GREASE FILTERS: Removable 18 GA.S.S. "V" section, measuring 510*510*50 mm thick, full compliment to be furnished. Set at an angle of 45 deg. in full-length w/bottom of filters set in continuous channel. Grease gutter on center & sides. Four (4) no. S.S. grease collecting drawers. Size and nos. of duct collars for exhaust as per HVAC consultants. LIGHTS. Bulkhead lights, diffusing glass, wiring in heat proof conduits, 100 watts each, 220V-50C-1Phase. MISCELLANEOUS Built in equal sections, w/ continuous plenum and field joints for bolting at the site. Suspended from ceiling in both fronts w/ hanger rods & provided with turn buckles, electrical junction box. Hood plenum top shall be closed with # 18 GA S.S. sheets and provided with 75mm high duct collar flange connections, for making connection to exhaust duct. FIRE SUPRESSION Unit shall be provided with water fog sprinkler system fusible links & w/ sprinkler sensor heads located below the filter assembly, complete w/ controls, piping & sensors, supply of fusible links sprinklers, piping and controls by another agency, hood supplier to provide cutouts & clamps to support the fire suppression system, fusible links to get activated at 350 deg. Fire suppression by fire safety contractor.

Item No.2.15/2.15A

COMBI OVEN AND ATAND WITH TRAYS ARRANGEMENTS

Qty 01

BRAND: MKN

MODEL: GN 10

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.16 WATER COOLER 150LIT D

Qty 01

750mm W x 500 mm D x Height as per site mm.

Top open insulated lid

50mm thick PUFF insulation.

20SWG outer body s.s. sheet (Food Grade)

22SWG inner tank s.s. sheet (Food Grade)

Compressor-Kirlosker 1TN HAG515

Thermostat.

1/2” dia float valve for level maintain.

1/2” dia tank cleaning valve

2 nos. Push type tape

Drip tray with the provision of flexible drainage pipe

14x14x4ROW condenser unit

GEM 1/10HP GEM condensing fan motor

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.17 WORK TABLE TWO UNDERSHELF

Qty 01

Over all size L600Xw800x850mm+150MM high Back splash on the rear side.

Top in 16swg s.s. sheet bent 50mm and 12mm on all sides excepting sides with splash

back.

Top sound dampened by an approved method.

Sides splash raised 150mm above the working height of 850mm bent 25mm at 90 deg, and down 12mm.

Top reinforced by 12/25x100x25/12mm channels of 18swg SS sheet.

Uprights in 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar

Item No.2.18 WALL SHELVES Qty 02

SIZE: Each of 600mm long x 300 mm Deep each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.19 CHILLER WITH WORK TOP AND GN PAN

Qty 01

OVERALL SIZE: L1800 x W750 x H 850 + 150 mm High to work top on feet. WORK TOP: Top of 18 GA. S.S secured to a fully welded 38mmx38mmx3mm thick. Boxed S.S. angle frame work, Front, rear & left of work top flanged down 50mm flush with body cladding, Right turned up 150mm , returned 25mm & down 12mm, rear gap of splashes closed with # 20 Ga. S.S. sheet. EXT. CLADDING: 20 GA. S.S. on all sides INT. CLADDING: 20 GA. S.S. fully coved interior tank. DOOR: Two (2) nos. Insulated doors with 18 GA. S.S. cladding, with top formed handle, magnetic gasket, locking Arrangement hinged as shown in front, built-in cylindrical locks keyed alike for all doors. REFER STORAGE: Bottom refrigerated storage, fully coved internal corners and compressor housing on right side w/ louvered panels. (6) Nos. S.S. removable& adjustable wire shelves INTERNAL TEMP: 0 degree C to + 4 degree C REFRIGERATION: 1.0 HP air-cooled “Kirloskar” normal temp. Type, housing on right side as shown complete with louvered access panels, digital read out thermometer, cord, with time delay auto start, with power cord, 220V-50C-1Phase, and S.S louvered shutter at front, cable entry from bottom. LEGS: Two pairs of 150mm high counter type S.S adjustable feet GN PANS: 1/4 six (6) nos. top mounted x depth 150 mm COOLING: Forced draft cooling with fan, refrigeration system mounted on a S.S slide out drawer channel angle frame work for ease in maintenance. CONDENSATE: Bottom of internal storage pitched to center & provided with 25mm dia. Waste outlet, removable perforated # 18 GA. S.S false bottom in 3-equal pieces with lift out finger holes, with all sides turned down 25mm and in 12mm, provide a slide out S.S drip tray below waste. INSULATION: 50mm thick P.U. injected foam through out STRAINER BASKET: Two (2) no. # 20 GA. S.S 50mm high removable perforated W/handle, size to fit sinks.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.20 PICK UP COUNTER TWO TIER Qty 01

300mm Deep 2 nos.

Mounted on Item no. 2.19

750mm high upright with middle shelf fixed at 425mm height

25mm OD s.s. pipe upright fixed to 18SWG s.s. channels welded to the underside shelf

Gussets of s.s. rounds

Extra uprights to be provided for overhead shelf wider than 1800mm

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No. 2.21 SINK UNIT WITH OVERHEAD SHELF 01 SIZE: L650 x D750 x H850+150 mm High to work top on legs. TOP: 16 GA. S.S, secured to 38mm x 38mm x 3mm thick M.S. welded angle frame with all sides turned down 50mm & in 12mm, SINK: Fully coved No. 16 GA. SS, of 300 mm x 300 mm x 225 mm Deep as shown on right side, sink complete w/ lever handle operated 50mm dia waste, rear connected overflow and deck mounted swivel type mixer faucet. Sink location as per layout design LEGS: Four (4) Nos. S.S tubular, with S.S. adjustable feet, cross braced at rear and both sides. MISC: One (1) No. tool drawer Fully SS enclosed slide out to be, provided on left side & furnished with removable GN 1/1 size 150 mm high die pre OVERHEAD SHELF: 450mm Deep 1 nos.

Mounted on Item no. 2.21

750mm high upright shelf fixed

25mm OD s.s. pipe upright fixed to 18SWG s.s. channels welded to the underside shelf

Gussets of s.s. rounds

Extra uprights to be provided for overhead shelf wider than 1800mm

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.22 MICROWAVE OVEN

Qty 01

BRAND: SAMSUNG OR ANY STANDARD BRAND

MODEL: 23L SOLO

Epoxy Coating

Rapid Defrost

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.23 UNDER COUNTER CHILLER Qty 01

OVERALL SIZE: L2000 x W750 x H 850 + 150 mm High to work top on feet. WORK TOP: Top of 18 GA. S.S secured to a fully welded 38mmx38mmx3mm thick. Boxed S.S. angle frame work, Front, rear & left of work top flanged down 50mm flush with body cladding, Right turned up 150mm , returned 25mm & down 12mm, rear gap of splashes closed with # 20 Ga. S.S. sheet. EXT. CLADDING: 20 GA. S.S. on all sides INT. CLADDING: 20 GA. S.S. fully coved interior tank. DOOR: Two (2) nos. Insulated doors with 18 GA. S.S. cladding, with top formed handle, magnetic gasket, locking Arrangement hinged as shown in front, built-in cylindrical locks keyed alike for all doors. REFER STORAGE: Bottom refrigerated storage, fully coved internal corners and compressor housing on right side w/ louvered panels. (6) Nos. S.S. removable& adjustable wire shelves INTERNAL TEMP: 0 degree C to + 4 degree C REFRIGERATION: 1.0 HP air-cooled “Kirloskar” normal temp. Type, housing on right side as shown complete with louvered access panels, digital read out thermometer, cord, with time delay auto start, with power cord, 220V-50C-1Phase, and S.S louvered shutter at front, cable entry from bottom. LEGS: Two pairs of 150mm high counter type S.S adjustable feet COOLING: Forced draft cooling with fan, refrigeration system mounted on a S.S slide out drawer channel angle frame work for ease in maintenance. CONDENSATE: Bottom of internal storage pitched to center & provided with 25mm dia. Waste outlet, removable perforated # 18 GA. S.S false bottom in 3-equal pieces with lift out finger holes, with all sides turned down 25mm and in 12mm, provide a slide out S.S drip tray below waste. INSULATION: 50mm thick P.U. injected foam throughout STRAINER BASKET: Two (2) no. # 20 GA. S.S 50mm high removable perforated W/handle, size to fit sinks.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.24 HOT BAIN MARIE

Qty 01

SIZE: L600 XW750 x H 850+150mm High to work top on feet TOP: 16 GA. S.S all sides of top turned down 2” & flush w/ body cladding, secured to fully welded boxed S.S. angle framework. CLADDING: All sides S.S of 20 GA.S.S. LEGS Total Four (4) pairs S.S. tubular with adj. feet & cross braced with 1” Dia at rear & both sides. BAIN MARIE: # 16 GA. integral w/top & suitable to accommodate five (3) nos. half size GN Pan 325x265 x150mm deep food pans with flush lids ( GN Pan By – Kit Eqpt. Supplier) INSULATION 50mm thick, tightly packed glass wool. Sheathed w/ 20 Ga. SS sheets on exterior. WASTE Bottom sloped to 25mm DIA, w/ angle valve. FAUCET Wall mounted 12mm HW Filler Faucet "Parko" make. MISCL. Provide 3.0 KW electric heating elements clamped 25mm off the bottom. Complete w/ Thermostat, on-off switch, red light and S.S recessed control panel. ELECTRICAL RATING 220V-50C-1Phase,

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.25 STORAGE CABINET WITH SLIDING DOOR Qty 01

SIZE: L3100 x D375x 850+150 mm H to work top on legs. OR (Length 1550x2) TOP: # 16 GA. S.S, secured to 38mmx38mmx3mm thick welded S.S. angle frame with front &left turned down 50mm & in 12mm, rear & right turned up 150mm, returned 25mm &down 12mm. UNDERSHELVES: Under shelf shall be reinforced w/ # 18 G.A. S.S. hat type channels with rear and both sides of shelves turned up by 50mm and tac welded to cladding and frame work with fronts turned down 40mm & in 12mm., Reinforc SPLASH: of 150mm high against walls as required LEGS: Four (4) Nos. 38mmx38mmx # 16 S.S tubular, with S.S. adjustable feet.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.26 PICKUP COUNTER (FOOD WARMER) TWO TIER

Qty 01

375mm Deep 2 nos. Long 2500 and mounted on Item no. 2.23 & 2.24 18swg s.s. reflector One Philip make Cromptalux heat lamp for the reach 300mm width shelf Individual toggle switch for each lamp 3 to 4 lamp (as per space) required Ceramic lamp holder Teflon insulated wiring 3 Core main lead with socket 750mm high upright with middle shelf fixed at 425mm height 25mm OD s.s. pipe upright fixed to 18SWG s.s. channels welded to the underside shelf Gussets of s.s. rounds Extra uprights to be provided for overhead shelf wider than 1800mm

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.27 FIVE TIER SS RACK 1 NO. SIZE L400xW350x2100mm High on castors. SHELVES: unit provided w/six (6) shelves, shelves constructed of No.18 GA.S.S with all sides turned out 12 mm @ 450 Marine edges, turned down 38 mm and in 12 mm, under side of shelves reinforced with No.16 GA. 12/25x100x25/12mm S.S hat type channels. UPRIGHTS: Five nos. Each of 14 GA.S.S. 40 mm x 40 mm x 14G vertical angles uprights, and shelves fully welded to uprights. Uprights at bottom provided with extended flanges and provided with 125 mm dia rubber tiered castors swivel type, all with brakes. Bottom shelf provided at 250 mm AFF, first shelf 450 mm above bottom shelf with remaining shelves equally spaced above first shelf.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.28 WALK IN CHILLER 1 NO.

External Room Dimensions (LX B X H): 2100x1800x2400 (External Height) Desired temperature range : +20C to +80C+_ 2 Deg.C Product stored : Mixed Kitchen Items for Storage Product incoming temperature : +10 to +25 0C Pull down time desired : 24 hours No of Door openings per day/hour: 10-15 opening/day. Wall & Ceiling Insulation and thickness: 60 mm thick prepainted GI PUF panel

inside/prepainted GI PUF panels outside

Floor insulation and thickness: 60 mm thick PUF Insulation (Kota finish over floor insulation)

Door type and size: Swing door 78’’X34’’60 mm thick prepainted GI inside/prepainted GI PUF panels outside sheet, strip curtain, kick plate

No of Doors One

Product stacking details : On Racks

Ambient temperature: 40 to 450C

Blue Star make refrigeration unit with Refrigerant of 6000 BTUH x 01 Nos. model RUAH – 0612KP with

Electric Light Fittings Vapour Proof Lights – 02 Nos.

Refrigerant : R-22a

Power supply: 230V/400V/3ph/1ph/50Hz

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.29 FOUR TIER STORAGE RACK 1 SET

FROM CAMBRO FULL Item No. 2.30 WORK TABLE WITH SINK AND TWO

BELOW SHELF QTY. 01

SIZE: L1500 x W 600 x H 850+150 mm High to work top on legs. TOP: 16 GA. S.S, secured to 38mm x 38mm x 3mm thick M.S. welded angle frame with all sides turned down 50mm & in 12mm, SINK: Fully coved No. 16 GA. SS, of 500 mm x 500 mm x 225 mm Deep as shown on the right side, sink complete w/ lever handle operated 50mm DIA waste, rear connected overflow and deck mounted swivel type mixer faucet. Sink location as per layout design LEGS: Four (4) Nos. S.S tubular, with S.S. adjustable feet, cross braced at rear and both sides only below the sink area. Item No.2.31 WALL SHELVES Qty 02

SIZE: Each of L1500 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from the wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.32 BUFLLOW CHOPPER

Qty 01

BRAND: ANY STANDARD MAKE

MODEL: TABLE TOP

Item No.2.33 SLICING MACHINE

Qty 01

BRAND: ANY STANDARD MAKE

MODEL: TABLE TOP

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.34 WORK TABLE TWO UNDERSHELF

Qty 01

Over all size L1500XW600xH850mm+150MM high Back splash on the rear side.

Top in 16swg s.s. sheet bent 50mm and 12mm on all sides excepting sides with splash

back.

Top sound dampened by an approved method.

Sides splash raised 150mm above the working height of 850mm bent 25mm at 90 deg, and down 12mm.

Top reinforced by 12/25x100x25/12mm channels of 18swg SS sheet.

Uprights in 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar

MISC: One (1) No. tool drawer Fully SS enclosed slide out to be provided on left side Item No.2.35 WALL SHELVES Qty 02

SIZE: Each of L1500 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.36 FOOD PROCESSOR

Qty 01

BRAND: ROBOCOP

MODEL: TABLE TOP

Item No.2.37 MEAT MINCER

Qty 01

BRAND: HOBART

MODEL: TABLE TOP

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No. 2.38 TWO DOOR UPRIGHT FREEZER

Qty 01

WILL BE USED EXISTING ONE

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.39 WORK TABLE TWO UNDERSHELF

Qty 01

Over all size L1000xW600xH850mm+150MM high Back splash on the rear side.

Top in 16swg s.s. sheet bent 50mm and 12mm on all sides excepting sides with

splash back.

Top sound dampened by an approved method.

Sides splash raised 150mm above the working height of 850mm bent 25mm at 90 deg, and down 12mm.

Top reinforced by 12/25x100x25/12mm channels of 18swg SS sheet.

Uprights in 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar

MISC: One (1) No. tool drawer Fully SS enclosed slide out to be provided on left side

Item No.2.40 WALL SHELVES Qty 02

SIZE: Each of L1000 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.41 STORAGE CABINET

Qty 01

SIZE: L2400 x D450x 850+150 mm H to work top on legs. OR (Length 1550x2) TOP: # 16 GA. S.S, secured to 38mmx38mmx3mm thick welded S.S. angle frame with front &left turned down 50mm & in 12mm, rear & right turned up 150mm, returned 25mm &down 12mm. UNDERSHELVES: Under shelf shall be reinforced w/ # 18 G.A. S.S. hat type channels with rear and both sides of shelves turned up by 50mm and tac welded to cladding and frame work with fronts turned down 40mm & in 12mm., Reinforc SPLASH: of 150mm high against walls as required LEGS: Four (4) Nos. 38mmx38mmx # 16 S.S tubular, with S.S. adjustable feet.

Item No.2.42 WALL SHELVES Qty 02

SIZE: Each of L2400 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.43 FIVE TIER SS STORAGE RACK WITH LOCK

AND KEY PROVISION 1 NO.

SIZE L100Xw4000x2400mm High SHELVES: unit provided w/six (6) shelves, shelves constructed of No.18 GA.S.S with all sides turned out 12 mm @ 450 Marine edges, turned down 38 mm and in 12 mm, under side of shelves reinforced with No.16 GA. 12/25x100x25/12mm S.S hat type channels. UPRIGHTS: Five nos. Each of 14 GA.S.S. 40 mm x 40 mm x 14G vertical angles uprights, and shelves fully welded to uprights. Uprights at bottom provided with extended flanges and provided with 125 mm dia rubber tiered castors swivel type, all with brakes. Bottom shelf provided at 250 mm AFF, first shelf 450 mm above bottom shelf with remaining shelves equally spaced above first shelf. Item No.2.44 SS COUNTER WORK TOP BELOW TWO

SHELF AND SLIDING DOOR

Qty 01

SIZE: L1800 x D600x 850+150 mm H to work top on legs. OR (Length 1100x2) TOP: # 16 GA. S.S, secured to 38mmx38mmx3mm thick welded S.S. angle frame with front &left turned down 50mm & in 12mm, rear & right turned up 150mm, returned 25mm &down 12mm. UNDERSHELVES: Under shelf shall be reinforced w/ # 18 G.A. S.S. hat type channels with rear and both sides of shelves turned up by 50mm and tac welded to cladding and frame work with fronts turned down 40mm & in 12mm., Reinforc SPLASH: of 150mm high against walls as required LEGS: Four (4) Nos. 38mmx38mmx # 16 S.S tubular, with S.S. adjustable feet.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.45 WALL SHELVES Qty 02

SIZE: Each of L1800 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

Item No.2.46 SOILED DISH TABLE W/ GARBAGE

CHUTE Qty 01

SIZE: L1000xW 600 deep x 850+150high to working surface on legs. TABLE TOP: 14 GA. S.S with 75mm raised channel shaped fronts, and rear towards the drop-off side, turned up 75mm, turned-out 40mm @ 90deg, turned down 50mm & in 12mm. SCRAP CHUTE: One(1) 150mm dia x 100mm high welded to top w/raised coved opening, as shown. LEGS: Four (4) Nos. S.S tubular, with S.S. adjustable feet, cross braced at rear and both sides

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.47 WALL SHELVES Qty 02

SIZE: Each of L1000 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

Item No. 2.48 WORK TABLE WITH SINK

01

SIZE: L850 xW600 x H850 + 150 mm High to work top on legs. TOP: 16 GA. S.S, secured to 38mm x 38mm x 3mm thick M.S. welded angle frame with all sides turned down 50mm & in 12mm, SINK: Fully coved No. 16 GA. SS, of 450 mm x 450 mm x 225 mm Deep as shown on right side, sink complete w/ lever handle operated 50mm dia waste, rear connected overflow and deck mounted swivel type mixer faucet STRAINER BASKETS: For both sinks 50 mm High 20 GA. S.S. removable perforated with handles. Size to fit sinks. LEGS: Four (4) Nos. S.S tubular, with S.S. adjustable feet, cross braced at rear and both sides. NOTE: This table is part of the DISH WASHER assembly, should be follow dishwasher specs.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.48A PRE RINSE HAND SHOWER

Qty 01

BRAND: IFB

MODEL: MOUNTED ON SINK ITEM NO 2.48

Item No.2.49 DISH WASHER

Qty 01

BRAND: IFB

MODEL: IFB- ProTech 813

Item No.2.50 CLEAN DISH LANDING TABLE WITH ONE

BOTTOM SHELF Qty 01

SIZE: 1200mm W x 600 mm D x 850+150 mm H to work top on legs. TOP: 16 GA. S.S, secured to 38mmx38mmx3mm thick welded S.S. frame with front turned down 50mm & in 12mm, splash turned up 150mm against walls, returned 25mm &down 12mm. Three sides covering front open SPLASH: of 150mm high against walls as required LEGS: Four (4) Nos. 40mm Dia # 16 G S.S tubular, with S.S. adjustable feet. NOTE: This table is part of the DISH WASHER assembly, should be follow dishwasher specs.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.50A WALL SHELVES Qty 02

SIZE: Each of L12000 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

Item No.2.51 SINGLE SINK UNIT (POT WASH)

Qty 01

SIZE: L750 x W750 x H600+150 mm(Back Splash Three Sides Front Open) High to work top on legs. TOP: 14 GA. S.S, front turned up 75mm, turned out 40mm , turned down 75mm & in 12mm, rear & sides turned up 150mm, returned 40mm @ 45 degree & down 12mm. SPLASH: Rear & of 150mm high. (Check walls) SINK: Fully coved # 14 GA. S.S, of 400 mm x 500 mm x 350 mm Deep as shown on plan, sink complete w/ lever handle Operated 50mm dia waste, rear connected overflow and One no. splash mounted swivel type mixer faucet. STRAINER BASKETS: For sinks 50 mm High 20 GA. S.S. removable perforated with handles. Size to fit sinks. LEGS: Six (4) Nos. S.S tubular with S.S. adjustable feet secured to S.S. Welded frame work.

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.52 FIVE TIER SS RACK 2 NO. SIZE: L600Xw600x2400 High SHELVES: unit provided w/six (6) shelves, shelves constructed of No.18 GA.S.S with all sides turned out 12 mm @ 450 Marine edges, turned down 38 mm and in 12 mm, under side of shelves reinforced with No.16 GA. 12/25x100x25/12mm S.S hat type channels. UPRIGHTS: Five nos. Each of 14 GA.S.S. 40 mm x 40 mm x 14G vertical angles uprights, and shelves fully welded to uprights. Uprights at bottom provided with extended flanges and provided with 125 mm dia rubber tiered castors swivel type, all with brakes. Bottom shelf provided at 250 mm AFF, first shelf 450 mm above bottom shelf with remaining shelves equally spaced above first shelf. Item No.2.53 WORK TABLE TWO UNDERSHELF

Qty 01

Over all size L1200Xw400xH850mm+150MM high Back splash on the rear side.

Top in 16swg s.s. sheet bent 50mm and 12mm on all sides excepting sides with splash

back.

Top sound dampened by an approved method.

Sides splash raised 150mm above the working height of 850mm bent 25mm at 90 deg, and down 12mm.

Top reinforced by 12/25x100x25/12mm channels of 18swg SS sheet.

Uprights in 38x38x16swg s.s. square tube

S.S. bullet feet of 20mm s.s. round bar

MISC: One (1) No. tool drawer Fully SS enclosed slide out to be provided on left side

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.54 WALL SHELVES Qty 02

SIZE: Each of L1000 x W300 mm each. BRACKETS: # 14 GA.S.S. Cantilevered secured to under side of shelf with acorn nuts and to wall with anchor fasteners. CONSTRUCTION: # 18 GA.S.S. Shelves w/rear & both side turned up 50mm & hemmed on the outside, front turned down 40mm & in 12mm. MOUNTING HEIGHT: 1400 mm AFF and 1700 mm AFF, clear 25mm away from wall.

Item No. 2.55 RO SYSTEM

01

Specs. and measurements as per MEP Design

Item No.2.56 INSECT KILLER

Qty 01

Tube size 450mm or 600mm as per site (Make any standard brands)

MS Construction

Powder coated finish

2nos.Ultra violet tubes of Philips make

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.57 AIR CURTAIN

Qty 01

Over all size as per site.

1/2hp motor 1200mm wide air curtain

Twin blower up to 1200mm wide air curtain

Two nos. 1/2hp motors above 1200mm wide air curtain

Four blower above 1200mm wide air curtain

240 Volt operation

1440 RPM motor

Any standard brand.

Item No.2.58 HAND WASH SINK

Qty 01

Overall size 450x450x100mm

Deep drawn stainless steel sheet

25mm DIA drain, waste

Punched hole for faucet

THE DECK INDIA HABITAT CENTRE-NEW DELHI 11/11/2016

Item No.2.59/2.59A

CONVECTION OVEN AND STAND WITH TRAYS ARRANGEMENTS

Qty 01

Convection Oven with Humidity

Make: Unox -Italy

Model: XFT -193

Capacity: 4x600x400

Max temp: 260 0C.

Manual Humidity

Electrical: 6.3 kw Electrical :415/50/3

Size: mm 800x 774x509 HT