ISO 3183 2012
-
Upload
pamela552fq4859 -
Category
Documents
-
view
887 -
download
93
description
Transcript of ISO 3183 2012
-
raising standards worldwide
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
BSI Standards Publication
BS EN ISO 3183:2012
Petroleum and natural gas industries Steel pipe for pipeline transportation systems
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012 BRITISH STANDARD
National foreword
This British Standard is the UK implementation of EN ISO 3183:2012. It supersedes BS EN 10208-1:2009 and BS EN 10208-2:2009, which are withdrawn.
The UK participation in its preparation was entrusted to TechnicalCommittee PSE/17/2, Transmission pipelines.
A list of organizations represented on this committee can be obtained on request to its secretary.
This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.
The British Standards Institution 2013. Published by BSI Standards Limited 2013
ISBN 978 0 580 73062 7
ICS 75.200; 77.140.75
Compliance with a British Standard cannot confer immunity from legal obligations.
This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2013.
Amendments issued since publication
Date Text affected
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM
EN ISO 3183
November 2012
ICS 75.200; 77.140.75 Supersedes EN 10208-1:2009, EN 10208-2:2009
English Version
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012)
Industries du ptrole et du gaz naturel - Tubes en acier pour les systmes de transport par conduites (ISO
3183:2012) Erdl- und Erdgasindustrie - Stahlrohre fr
Rohrleitungstransportsysteme (ISO 3183:2012)
This European Standard was approved by CEN on 22 September 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION C O M I T E U R O P E N D E N O R M A LI S A T I O N EUR OP IS C HES KOM ITEE FR NOR M UNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members.
Ref. No. EN ISO 3183:2012: E
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012EN ISO 3183:2012 (E)
3
Foreword
This document (EN ISO 3183:2012) has been prepared by Technical Committee ISO/TC 67 "Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries" in collaboration with Technical Committee ECISS/TC 110 Steel tubes, and iron and steel fittings the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2013, and conflicting national standards shall be withdrawn at the latest by November 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 10208-1:2009, EN 10208-2:2009.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 3183:2012 has been approved by CEN as a EN ISO 3183:2012 without any modification.
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
ISO 2012 All rights reserved iii
Contents
Foreword ............................................................................................................................................................................. v
Introduction ....................................................................................................................................................................... vi
1 Scope ...................................................................................................................................................................... 1
2 Conformance ........................................................................................................................................................ 12.1 Units of measurement ........................................................................................................................................ 12.2 Rounding ............................................................................................................................................................... 12.3 Compliance to this International Standard ................................................................................................... 1
3 Normative references ......................................................................................................................................... 2
......................................................................................................................................... 5
5 Symbols and abbreviated terms ................................................................................................................... 115.1 Symbols ............................................................................................................................................................... 115.2 Abbreviated terms .............................................................................................................................................12
6 Pipe grade, steel grade and delivery condition .........................................................................................136.1 Pipe grade and steel grade .............................................................................................................................136.2 Delivery condition .............................................................................................................................................14
7 Information to be supplied by the purchaser ............................................................................................157.1 General information ..........................................................................................................................................157.2 Additional information .....................................................................................................................................16
8 Manufacturing ....................................................................................................................................................198.1 Process of manufacture ..................................................................................................................................198.2 Processes requiring validation ......................................................................................................................218.3 Starting material ................................................................................................................................................218.4 Tack welds ...........................................................................................................................................................228.5 Weld seams in COW pipe ................................................................................................................................228.6 Weld seams in SAW pipe .................................................................................................................................228.7 Weld seams in double-seam pipe .................................................................................................................238.8 Treatment of weld seams in EW and LW pipes .........................................................................................238.9 Cold sizing and cold expansion ....................................................................................................................238.10 Coil/plate end welds .........................................................................................................................................238.11 Jointers ................................................................................................................................................................248.12 Heat treatment ....................................................................................................................................................248.13 Traceability ..........................................................................................................................................................24
9 Acceptance criteria ...........................................................................................................................................249.1 General .................................................................................................................................................................249.2 Chemical composition .....................................................................................................................................249.3 Tensile properties ..............................................................................................................................................299.4 Hydrostatic test ..................................................................................................................................................339.5 Bend test ..............................................................................................................................................................339.6 Flattening test .....................................................................................................................................................339.7 Guided-bend test ...............................................................................................................................................339.8 CVN impact test for PSL 2 pipe .....................................................................................................................349.9 DWT test for PSL 2 welded pipe ....................................................................................................................359.10 Surface conditions, imperfections and defects ........................................................................................ 359.11 Dimensions, mass and tolerances ...............................................................................................................379.12 Finish of pipe ends ...........................................................................................................................................429.13 Tolerances for the weld seam ........................................................................................................................449.14 Tolerances for mass .........................................................................................................................................479.15 Weldability of PSL 2 pipe.................................................................................................................................47
10 Inspection ............................................................................................................................................................4810.1 Types of inspection and inspection documents ....................................................................................... 48 ...........................................................................................................................................49
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
iv ISO 2012 All rights reserved
11 Marking .................................................................................................................................................................7711.1 General .................................................................................................................................................................7711.2 Pipe markings .....................................................................................................................................................7711.3 Coupling markings ............................................................................................................................................7911.4 Marking of pipe to multiple grades ...............................................................................................................80 .........................................................................................................8011.6 Pipe processor markings ................................................................................................................................80
12 Coatings and thread protectors ....................................................................................................................8112.1 Coatings and linings .........................................................................................................................................8112.2 Thread protectors ..............................................................................................................................................81
13 Retention of records .........................................................................................................................................81
14 Pipe loading ........................................................................................................................................................82
Annex A ..........................................................................................83
Annex B !"# .................................................. 84
Annex C Treatment of surface imperfections and defects ............................................................. 88
Annex D Repair welding procedure ......................................................................................................90
Annex E Non-destructive inspection for other than sour service or offshore service ........... 95
Annex F Requirements for couplings (PSL 1 only) ........................................................................106
Annex G PSL 2 pipe with resistance to ductile fracture propagation .......................................109
Annex H PSL 2 pipe ordered for sour service ................................................................................. 115
Annex I Pipe ordered as Through the Flowline (TFL) pipe .......................................................126
Annex J PSL 2 pipe ordered for offshore service ...........................................................................128
Annex K Non-destructive inspection for pipe ordered for sour service and/or offshore service ...............................................................................................................................................144
Annex L Steel designations ................................................................................................................149
Annex M PSL 2 pipe ordered for European onshore natural gas transmission pipelines ..152
Annex N ...................................................................................................................................................169
Annex O ...................................................................................................................................................170
Annex P Equations for threaded and coupled pipe and background equations for guided bend and CVN test specimens .....................................................................................................................171
Bibliography ...................................................................................................................................................................181
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Foreword
! " " !!!
#!"$!!!!!
!
%&%%!!#!!!'
#'!!!
!!!"(#')!%*
!!!
) !! !
!!" "! +",-.!
/!""$!"!
3453!!'
('6,%Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries%"!
'*%Pipeline transportation systems.
89"46('6,('*$:89"!"89;*4*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Introduction
"+">
B /!-:C;;"4!*
B :*+"="!"!"/?G%+"!!!"=!!!!"!!%"!""!!C
B :*!"!!"/?9C
B :*"!/?HC
B J"KLK:/?C
B :*!/?MC
?
B :*#""/?D
B #+"!"!"+""'NE/?
+"?!="!
8""!%+"?!!!"!!%!!!P!"+" ? !!% +"! !
"! ! ! " +" % "! !% " "+"%!%%"+"!""!
3453"!"!!"!!!!!"%+""!"!=!%!=!/!!%"!!+" (#')!%*%!%+"%!=!@*%K4/?%!"!"&8!%!"!"!=
vi ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
INTERNATIONAL STANDARD ISO 3183:2012(E)
Petroleum and natural gas industries Steel pipe for pipeline transportation systems
1 Scope
!= +" "!" "! !=! : 4 : * " """
!!
2 Conformance
2.1 Units of measurement
%?"Q'"Q'"K!=!%""%"!?)"?Q'"!!!"+"+"!
8"!=+"""Q'%!!""%""%!!"!!""!
"! ! % % ! Q '" Q' " Q !""QQ'!Q'
""
K?"%!
"!!""K?Q'"%"!!""
2.2 Rounding
Q % !! !=+"%!!""""&!=""?"%!!!5
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
/!!!"!"!!+""!!"!!"!"$!!
3 Normative references
! !" ! !" K !%!K"!%!!"!"
4;5&4%Metallic materials Charpy pendulum impact test Part 1: Test method
;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
/D/@;4%Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
/D/@-6%Standard Test Method for Leeb Hardness Testing of Steel Products
/D/4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
K"!"%=%
B 6@*@/D/@;4"!%
B ;55-/D/@;4%
B /-4!%
B ;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4.10COWH pipe"" "! ! "! ! &! "&!&!!"&!
4.11COWL pipe"" "! " "! ! &! "&!&!!"&!
4.12COW seam"!"!!&!"&!&!!"&!
4.13CW pipe"""!""!!""
4.14daughter coil%!"!%!""!more pieces of pipe
4.15daughter plate%!"%!""!or more pieces of pipe
4.16defect! ( " !!! ! !=
4.17electric weldingEW!!!&!%!!!P!!!"induction or conduction
4.18EW pipe"""!""!&&+"!!!
4.19EW seam""!!!
4.20$%! "!!!! !!""=!!%!P"?!""!
E# !%?"?"
6 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4.21gas metal-arc welding!"!!!!!! !"" !" ! % ! ?"?"
E# '!""=!
4.22heat
"!!!!!
4.23HFW pipehigh-frequency electric welded pipe#8"!!"+"!+",
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4.31
!!%!+"%!? !" % "" " &!!"!"!
4.32lamination!%"!
4.33laser weldingLW! " & !+" "! !!!%"%?"?"
4.34low-frequency electric welded pipeLFW pipe#8"!!"+"!,
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4.42normative elements!!!"%!"+"
E# (#')!%*
4.43pipe bodyD: entire pipe
4.44pipe bodywelded pipe%?!"&!H/_
4.45pipe grade
E# '!!(!!
4.46pipe mill=%!!&!
E# /44@6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4.54SAWH pipe"""!!"!"&!!
4.55SAWL pipe"""!""!"&!
4.56SAW seam"!"!"&!
4.57seamless pipeSMLS pipe"%"!&!%!!!!="!%
4.58service condition!"!="!"!
E# %J"!LJ!L!!
4.59shielded metal arc welding! "!!!! !!!%!!electrode covering
E# '!""!!
4.60tack weld!"""""=weld is produced
4.61test piece!=%!"&!%" +"! "
4.62test unit!+"!="!=!%!("!!!!%&
"!"!"&"!"!
4.63thermomechanical forming&!"!"%!=!"!"% !! !! %"!!%!!%"%&!"
CAUTION Subsequent heating above 580 C (1 075 F) typically can lower the strength values.
10 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
4.64thermomechanical rolled!"&!!%!=!"!"%!!!!%"!!%!!%"%&!"
CAUTION Subsequent heating above 580 C (1 075 F) typically can lower the strength values.
4.65undercut$!"=
4.66unless otherwise agreed+""+"""!""!!="!
E# /!%?%!,*
4.67welded pipe '8% '8H% '8:% #8% HK8% :K8% :8% /8H /8: =
5 Symbols and abbreviated terms
5.1 Symbols
a !(%?!
Af !"%?!"!
Agb "&(%?!
AI !&!%?+"+"!
AP !&!%?+"+"!
AR !&!&%?+"+"!
A?! !!!&!%?+"+"!
b !=!%?!
B !!""?
C !%!"""
CEIIW !+"%""8+"
CEPcm !+"%"!!&G!+"+"
d !!"%?!
D !="%?!
D "!"&"%?!
Db "!"&"%?!
f +"!%?H!!!
ISO 2012 All rights reserved 11Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
KN "&'N&!%?$"&"!
L %?
NL !="%!"%?!
P !"%?!"+"!
PR "&%?!"+"!
Q !=!!"%?!
r "%?!
r ""&%?!
rb ""&%?!
ro ""%?!
Rm %?!"+"!
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
EW !!!!!"!!""!"
H/_ &!
HG8 G
HK8 &+"!!!!""!"
H' &"!!!
HF' F!%'!
HN N!
R +"!
LFW &+"!!!!""!"
LW !""!"
D !!
NDT non-destructive testing
PSL "!!=!
PT
/8H "&!!!""!"
SAWL "&!"!""!"
SI "
SSC "=!!
SWC &!!
TFL Through the Flowline
USC Q!""
UT "!
6 Pipe grade, steel grade and delivery condition
6.1 Pipe grade and steel grade
6.1.1 :4!4!"!=!!!
E# 9 / 9 G ! ! != " C%"!!!="""&"!="%?4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E#4 9G!!!="C%"!!!=""Q'"
E#* K"!%H;44
E#3 K!%M;44
E#; K#"%D;44
6.1.3 ""#""!:4
6.2 Delivery condition
6.2.1 K!%!:4"!""!=!!!="!)!:4:*4:*3
6.2.2 K:*%!!!!"!!=
Table 1 Pipe grades, steel grades and acceptable delivery conditions
PSL Delivery condition Pipe grade/steel grade%
PSL 1 /&%% :4,-/*-
:4,-/*-
L210 or A
PSL 1 /&%%!!%!!%%%C%%+"!D:
:*;-G
PSL 1 /&%%!!%!!%%%+"!
L290 or X42
:3*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
PSL Delivery condition Pipe grade/steel grade%
PSL 2 R"! :*;-RGR
:*@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
?@4443%@44334*C
!=!"?
7.2 Additional information
"!!!!=!>
"$!%!>
4 4%%
* !!!@*4@**%
3 !!!t *-%
4 !&?5@*%
* +"5@3%
3 !!!:4;%!%%
; !!!:*-%!%%%%%%%
- (9:6*-R}@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
! %>
4 !6*4%
* "+"!:49:*;-GD:4%
3 "*%%
; ""&/8:*%!%
- !=:4554%
6 "/8H!(54
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
34 &!!"444*%
3* !="!444;%
33 !=!"!!\44**44*6^%
3; &&!44*3%
3- !44*;%
36 !\44*6^%
3, !"=!44*,%
35 "44;4%
3@ ?!4*4*%
;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
8 Manufacturing
8.1 Process of manufacture
" "!" !!! !+"*3
&'*&+
Type of pipe or pipe end
PSL 1 pipe grade PSL 2 pipe grade
L175 or A25 b
L175P or A25P b
L210 or A
L245 or B
L290 or X42 to
L485 or X70
L245 or B to L555
or X80
L555 or X80 to L690
or X100
L690 or X100 to L830 or
X120Type of pipe
D: X X X X X X X
CW X X
LFW X X X X
HK8 X X X X X
LW X
SAWL c X X X X X X
/8H d X X X X X X
COWL c X X X X
'8H d X X X X
Type of pipe endG e X X X X
X X X X X X X
!!" X X X
f X X X X %"9:*@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table 3 Acceptable manufacturing routes for PSL 2 pipe
Type of pipe Starting material Pipe forming Pipe heat treatmentDelivery
condition
D: %
As-rolled R
E N
HE N
R"!tempering R
H!=
E N
R"!tempering R
HK8
E&! Cold forming H of
N
!!&coil Cold forming
H of D
H stress relieving of
entire pipe
D
As-rolled or !!&
coil
Cold formingE N
R"!tempering R
'reducing under controlled ""!
N
'!!
of pipe D
SAW or COW pipe
E&! Cold forming N
/&%!!&%
&
Cold forming E N
!!&! Cold forming D
R"! Cold forming R
/&%!!&%
&!
Cold forming R"!tempering R
/&%!!&%
&!
E N
55!
20 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
8.2 Processes requiring validation
K " "!" ! " !! +" ?!!!!!
!+">
B%&> =!!!&"!C!%"%!=C
B%&> C
B!!&%&> C!%"C
B!!&%&> "&C
B/8'8%?> %%C!%C
B/8'8%?> %%%?
8.3 Starting material
8.3.1 "!"+"
E# )!"+"+"!=!!=!!+" ! +" ! +" ! !P!!!?+"!!"!+"%!"(*@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
B !!C
B !(!!C
B !
!!!(!!!"
8.3.8 K!D%!(!!!"!53,=
B F!("!"!!((!!%!"!!%!+"!
B K :36
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
8.7 Weld seams in double-seam pipe
"&?45
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
8.10.3 %!(!&%!!"4-
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E# 9:4,-/*-&%%9:4,-/*-C%!=!"
9.2.2 For PSL 2 pipe with t *-%
CE C Mn6
Cr Mo V Ni CuIIW = + +
+ +( )+
+( )5 15
(3)
!!!!-
E# /"!!+"#+"*3!""
ISO 2012 All rights reserved 25Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table 4 Chemical composition for PSL 1 pipe with t 25,0 mm (0.984 in)
Steel grade (Steel name)
Mass fraction, based upon heat and product analyses %
.
C Mn P S V Nb Ti
?b ?b min. ? ? ? ? ?
Seamless pipe:4,-/*-
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table 5 Chemical composition for PSL 2 pipe with t 25,0 mm (0.984 in)
Steel grade
(Steel name)Mass fraction, based upon heat and product analyses
.?"
Carbon equivalent
.?"
C b Si Mn b P S V Nb Ti Other CEIIW CEPcmSeamless and welded pipes
:*;-FGF
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table 5 Chemical composition for PSL 2 pipe with t 25,0 mm (0.984 in) (continued)
Steel grade
(Steel name)Mass fraction, based upon heat and product analyses
.?"
Carbon equivalent
.?"
C b Si Mn b P S V Nb Ti Other CEIIW CEPcmWelded pipe
:*;-DGD
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
9.3 Tensile properties
9.3.1 K:4%6
9.3.2 K:*%,
Table 6 Requirements for the results of tensile tests for PSL 1 pipe
Pipe grade
Pipe body of seamless and welded pipesWeld seam of EW, LW, SAW and COW
pipesYield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table 7 Requirements for the results of tensile tests for PSL 2 pipe
Pipe grade
Pipe body of seamless and welded pipes
Weld seam of HFW,
SAW and COW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Pipe grade
Pipe body of seamless and welded pipes
Weld seam of HFW,
SAW and COW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Pipe grade
Pipe body of seamless and welded pipes
Weld seam of HFW,
SAW and COW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
9.4 Hydrostatic test
9.4.1 #?!@;*%!""
9.4.2 ! $! % "
$"!!"!$
9.5 Bend test
E!!!!"!!!"
E# K%?!6%;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
9.7.2 '!!!"!"!"$!%6%;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table 8 CVN absorbed energy requirements for pipe body of PSL 2 pipe
diameter
D
mm (in)
Full-size CVN absorbed energy, minimum
KN
M
Grade
:;4-}6
1) :*@
}/!-G66*-: (for USC units)
or
}/!-G465%3: (for SI units)
11.5.2 "J!-GL44-4!"!=!"!" ! +" / ! -G " " !" "! "! % % !!!/!=!D"!""J!-GL=!+"!!!=/"!!!/!-G
11.6 Pipe processor markings
!"!""!"!"'"44!!!"!""!"!"
!"!!"!""%"!!!!"!"
80 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
12 Coatings and thread protectors
12.1 Coatings and linings
12.1.1 #?!4*4*4*4;%!
12.1.2 %?!!""!!"!%"?!
12.1.3 %!!
12.1.4 %
12.2 Thread protectors
12.2.1 KD 6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
!"C
!!=?"!%!"&!"!=!8&!"+"=!!8R(RF/?/)
14 Pipe loading
"!"%"!" % ! !" "!% !% !&%!!%% "!! ! "%!% !
!!!!
E# K/F-:4 [18]/F-:8 [19].
82 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex A
A.1 Method
A.1.1 8"=!"!!""!!=!"
A.1.2 8 !"% ! ! +"=!!!"!
A.1.3 '!"!=!!"+"=!!"!"+"
A.2 Workmanship
A.2.1 !!!+"=!"!=!
A.2.2 ! $ @443;' $$
A.2.3 #!""!&!"!!"!/&!"!""!%!=46"&!4%6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex B
!"#
B.1 General
B.1.1 ?!="!"!"+"=!:*\,*!;*^/?H%/?M%(/?D
B.1.2 !!=""!%+"%+"!=!""!""
B.1.3 N=!"!"!"!!""!+"=!!!!'"G3%G;%G-%!
B.2 Additional information to be supplied by the purchaser
"!!!!=!>
+"=!!!!'"G3%G;%G-!G43C
+"!"G-*
_= `
G"!!
!"!""!"%"!"""!"
=!!!"%!%!!!"!"!"!">
!B>
4 (!"!"!%
* +"!! !"%%?!!%!"!!!!!%
3 !!!!"-%
; !!!%
- !!!"(!*
4 (!"!"!%
84 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
* +"!!%
3 !!!!"!(=!+"%
; &"!!!!!""!!%
- !!(!!!!!=!%
6 !!"!!%
, "+"! % ! ! ""!"!%
5 !%
@ "!!!!(!(!%
4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
3 !" !=!"+"=! ! !"% !""=!>
HK8>
!=+""%
!!!C
/8'8%%!(%$%!>
(P"?!""!"%!=!%
!"!"%%%"C
; /8'8>
!%
!!!!%
!"P"?!""!!!!!P"?%!%
!C
"!"D:>
4 &!&>
!!!!"!%!%
!!%!C
* &!!
B.4 Characteristics of the inspection and test plan
G "! !
!% "!" " "! "
=!!!"%!%!!!!!">
!!C
" ! ! !" "!"%"!!%"!C
! !(!!!%!C
+"!!C
!!!!C
!&!!C
"!%!C
=!!+"C
86 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
_ !
B.5.1 K +"=! "!" !"% != 45%H3%M,%(D,%!!%!"of the production.
B.5.2 +"!"+"=! != "!%+"=! "!"!"+"=!""!"!
B.5.3 K%"!"+"=!>
HK8>
4 !!%
* !!"!!!45%H3M,%
3 !=+""%
; " +" !!! H,*; H,33% M5*3M53*C
/8'8>
4 %
* (P"?!""!"%!=!%
3 !"!"%%%"%"!%
; !!"!!!45%H3M,%
- "+"!!!H,*;H,33%M5*3M53*%
6 !!!
B.5.4 "!!!!"!
E# "!+"!"!+"!=!!"!"!!%"!""!"!!+"!"!:6@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex C
Treatment of surface imperfections and defects
C.1 Treatment of surface imperfections
"!!!=!"!!&"
C.2 Treatment of dressable surface defects
C.2.1 /"!!&"
C.2.2 9 ! " "! contour of the pipe.
C.2.3 '!= !" !%%!%"&"!!!!%!"!!!@443*C%"!"&&"@4434"
C.3 Treatment of non-dressable surface defects
!&"!!
8!/8'8!!!'"';
!!"!!!"%
! $!
C.4 Repair of defects by welding
C.4.1 K:4%K:*%
C.4.2 #?!';4%!=/8'8!!"!"!K:*%"!?3%*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
C.4.4 8! 4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex D
Repair welding procedure
D.1 General
D.1.1 F
?C
!!!+"=!"C
! !!+"=!!!'")3
D.1.2 F>
"!"!C
"!&"!!C
! "!"&!
D.1.3 / !!! "!"!
%!""!
D.1.4 %
D.1.5 "!"!!"!"+"=!&"'&!"!=!&!"+"=!!"!"+"
j {!
D.2.1 General
D.2.1.1 8!"+"=!!!?%?!)*4*
D.2.1.2 / "!"% !" +"=! !! != 4-64;&4[23]%/!-:%;3rd Edition [17]/D#!}\*6^""!=)*3
D.2.1.3 K " ?% "! !"!%!"!
90 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
D.2.2 Essential variables
/?!"!!"+"=!>
!>
4 !!%"!"&!!%
* !%"!"&"!C
>
4 !!C"!%!!+"=%!>
:*@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
; !%a%+"="!"%"C
>"&"!%!-
4 ""+"=!%
* &
D.2.3 Mechanical testing
D.2.3.1 Number of test pieces
!!)*3*)*33!!"+"=!K!%!!!(see D.2.3.4).
D.2.3.2 Transverse tensile test
D.2.3.2.1 "!!?35
4-&!%K"5!!"!!"
E# /"K"5"!%"!!!
D.2.3.2.2 +""!=!
D.2.3.3 Transverse guided-bend test
D.2.3.3.1 "&!K")4%
D.2.3.3.2 #!!45
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
D.2.3.4.4 "!!!H/_%"!"
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
&j'}~&
Pipe grade
Dimension
mm (in)
r b rb b Agb b B b
L290 or X42 3%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex E
Non-destructive inspection for other than sour service or offshore service
E.1.1 @,4*%44;5;/EE&'&4/+"%+"=!&"!!?!""!"!&+"=
"+"=%&"!!?!4*
E.1.2 E&"!!!"!:4%*3
E.1.3 #"!:*3%:4"the supervision of Level 2 or 3 personnel.
E.2 Standard practices for inspection
#?!!=!=?%+"&"!!%"!! 4 4 4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table E.1 Pipe weld seam non-destructive inspection
Weld seam typeNon-destructive inspection method
Electromagnetic Ultrasonic Radiographic
EW !+" !
LW ! +" !
SAW ! +" b
COW ! +" !
'( ! +" b +"!#3*b F+"""!""!!!inspection.
E.3.1.2 /:*D::49:*;-G+"!D:&"!!"4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E.3.3 Pipe end inspection SMLS pipe
E.3.3.1 " "! !! ! ! +"% !"+"#34*%!"!!!"&"!"!!!%"!&!!"F!!!!#-;
E.3.3.2 t -%
B =!!>4*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E.4.3.6 R!"!8"!!!%R!=(!$!!!"!JKL!R!"!!
E# /?"R"!!!!
Table E.3 ISO 19232-1 wire-type IQI for radiographic inspection
Weld thickness
mm (in)
Essential wire diameter
mm (in)
FE wire set Wire number
8 (0.3)
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E.4.4.3 K!! "=!+"!!!!" ! "" ! !% % "!!!!+"'"#;3%+"!!"!&R)"%"F!"?RR#;3"?!!?-~!R!"""!
+"! %!"%?"!!"$!%!""!%&!!"&!+"R!!+"#;3
8+"+"#;3%!!""!!"!!"!&!
E.4.5 Acceptance limits for imperfections found by radiographic inspection
" &!"& ( &!& ! ?!
"#-#6%!"=(+"3>4
E#4 ! ! ! !! !!"!K!%!4-
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table E.6 Circular slag-inclusion-type and gas-pocket-type imperfections
Size
mm (in)
*size
mm (in)
Separation
(minimum) mm (in)
Number of imperfections in any 150 mm (6.0 in) length of weld
?"
Accumulated diameters of imperfections in any 150 mm (6.0 in) length of weld
?" mm (in)
3%*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E.5.2.5 F! = ! !
=!"!"
Table E.7 Reference indicators
Item
Reference indicators
Notch location
Notch orientation Notch dimensions Diameter of radially drilled
hole b
OD ID Longitudinal Transverse Depth c Length d Width
.?"
mm (in)?"
mm (in) mm (in)
#8 % % % f 4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
!!!!""!=""!!!
E# !&"!!%J!L"JL"
E.5.3.3 "$" "!&= ! !!!!!
E.5.3.4 "$!!!!D 6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
! K/8'8%!!!!"!&!"&!!+"#;-
E.5.5.3 #?!#--*!%!""!!!=!"+"!
E.5.5.4 K D: % "! ! "! ! !!!!#5!=!"!!"!!!@4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E# J!!!"!L!"!!"!
E.6.2 Equipment
+""!!!"!!="=!!!!!?"!>!!%
E.6.3 Magnetic particle inspection reference standard
+""!%"!""!""!"!"!"!"!""%?"=!"!!!!#6*
E.7 Residual magnetism
E.7.1 +"""!"!
E# N""%"+""!"!%!!!"!"
E.7.2 "!="&D 465%3
66*-&!"!!+""!"!+"!"!=&
E# D"!!
E.7.3 D""H&!" ! "C%!"%"H&!""!!!"!"!!!""
E.7.4 D"!%!!;
E.7.5 ""+"!"!=% "!" !K!!+"
"%"!!""
?!#,6
E.7.6 K"?@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
E.7.10 /!&" &""!!"+"#,6
E.8 Laminar imperfections in the pipe body of EW, SAW and COW pipes
E.8.1 K#8%%"!!"!
4*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex F
Requirements for couplings (PSL 1 only)
F.1 Material
F.1.1 K!" ! +":4 != ?!!!%!!%&"!!
F.1.2 '"9:4,-%:4,-%/*-/*-
F.1.3 #?!K4;%!"9:*4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table F.1 Coupling dimensions, masses and tolerances
diameter of pipe
D
mm (in)
Coupling dimensions
mm (in) Calculated coupling mass
kg (lb)
diameter
W b
minimum length
NL b
of recess
Q b
bearing face
b
4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Key4 !&&"* &&"NL !="W !="!"Q !=!b !=!D !="t !d
&"//!-:/!-'[21] !!!!
Figure F.1 Line pipe and coupling
108 ISO 2012 All rights reservedCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex G
PSL 2 pipe with resistance to ductile fracture propagation
G.1 General
G.1.1 ?!=:*!'NE!**!"!!"\,*!-;^?"!'NE!""!!"
E#4 /!"=!&!""=!'NE& " ! !" ! "! !" pipelines (see 9.8.2.2).
E#* ""%!"!"%!+"?!!!!!"!/!"!!"!!"&!!"!"
G.1.2 "!!'"9,94
'NE"""&!!C
'NE"""&!
G.2.2 "!!
'NE!"%
)8"\D -
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
G.3.3 "!!=9*4%!="!"&!
G.3.4 K!)8%!"5-.%""!="!
E# )8!"!="!8)85-.%"!!""!"!"!""!!%"""!!?
G.4 Test frequency
G.4.1 For welded pipe with D -
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
G.7 EPRG guidelines Approach 1
G.7.1 !"#"F!9"#F9"!" [10]!!"94%9*93"!"!""5%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table G.1 Minimum CVN absorbed energy requirements for a design factor of 0,625
diameter
D
mm (in)
Full-size CVN absorbed energy, minimum
KN
M
Pipe grade
:*;-G:*;-G
to L290 or X42
L290 or X42 to
:36
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table G.3 Minimum CVN absorbed energy requirements for a design factor of 0,80
diameter
D
mm (in)
Full-size CVN absorbed energy, minimum
KN
M
Pipe grade
:*;-G:*;-
G
L290 or X42
L290 or X42 to
:36
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
!""!"=G&!"!F!'
F'F *
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex H
PSL 2 pipe ordered for sour service
H.1 General
?!=:*"!\,*!--^
WARNING This annex shall not be applied to PSL 1 pipe as PSL 1 pipe is not considered suitable for sour service.
E# !+"!""!!""!!?"H2&!"!P"E/'#DF
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
"E)!*43*4;C
!!!!!!(*4;C
+ =!(3**C
!!"!!"D:33C
!"&"!!D:3;C
"D:E)!3;C
" "!!D:!!3;4C
"& !D:" P"? ! " !3;*C
"&!D:!"3;3C
? "&!!!3;;C
"4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
H.3.3 Pipe manufacturing
H.3.3.1 SMLS pipe
D:"!"!""!! !!="%!!"
H.3.3.2 Welded pipe
H.3.3.2.1 Q%!""!"!""!!"!/8:%/8HHK8
H.3.3.2.2 K HK8 % " ! " % !before welding.
H.3.3.2.3 '""!"!"N"!!""!""!!
H.3.3.2.4 HK8%"!!!"!!!! !!!'";%!" !% !"$!"&!%!""!!
H.3.3.2.5 % !& !( ! !( %"!!3
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table H.1 Chemical composition for pipe with t 25,0 mm (0.984 in)
Steel grade
Mass fraction, based upon heat and product analyses
.
?"
Carbon equivalent
.
?"
C b Si Mn b P S V Nb Ti Other!% CEIIW CEPcmSMLS and welded pipes
:*;-EGE
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table H.2 Requirements for the results of tensile tests
Pipe steel grade
Pipe body of SMLS and welded pipesWeld seam of HFW and SAW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
H.4.3 HIC/SWC test
"!&"!!!!!!!%!?"!!"#/4-4-6&*>*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
!"!!!!!'3'3!
>^ $>
P?!"
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
H.7.2.2 Samples for HIC/SWC tests
H'(8'!!!E/'#D
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
H.7.3.1.4 N" !!& % !!&! !!& %!!
H.7.3.2 SSC test
H.7.3.2.1 #?!H,3**%'>
B "!!!!E/'#D**
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
! %!K"H4!%!
H.7.4 Non-destructive inspection
K&"!!%H33*3H33*-/?
H.7.5 HIC/SWC retests
H'(8'!!!!!%"!"!"!%!=4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Dimensions in millimetres (inches)
b) SAW pipe
c) HFW pipe Weld centreline.b
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex I
Pipe ordered as Through the Flowline (TFL) pipe
I.1 General
?!=K:\,*!-;^
I.2 Additional information to be supplied by the purchaser
"!!!!=!>
;C
"$;
I.3 Dimensions and grades
K:D:"!="%!=!4
#
Q%K:"4*;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table I.1 Dimensions, masses per unit length and test pressures for TFL pipe
diameter
D
mm (in)
thickness
t
mm (in)
Calculated inside diameter
d
mm (in)
Grade
Mass per unit length
l
((
Hydrostatic test pressure
(minimum)
D
6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex J
PSL 2 pipe ordered for offshore service
J.1 General
?!=:*!\,*!-,^
E# ?!"+"!!"!?!
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
t) for pipe with t -%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
J.3.3 Pipe manufacturing
J.3.3.1 SMLS pipe
D:"!"!""!!!="%!!"!=!
J.3.3.2 Welded pipe
J.3.3.2.1 Q%!""!"!""!"!/8:%/8HHK8
J.3.3.2.2 KHK8%"!"%!before welding.
J.3.3.2.3 '""!"!"N"!!""!""!!
J.3.3.2.4 %"!!!"!!!!!!!/?%!"!%!"$!"&!%!""!!
J.3.3.2.5 % !&!%!!(%"!!3
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table J.1 Chemical composition for pipe with t 25,0 mm (0.984 in)
Steel grade
Mass fraction, based upon heat and product analyses
?" .
Carbon equivalent
?" .
C b Si Mn b P S V Nb Ti Other c CEIIW CEPcmSMLS and welded pipes
:*;-EGE
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
J.4.2 Tensile properties
J.4.2.1 M*
J.4.2.2 +" "% !!!!
J.4.3 Hardness test
K!"$!M53*%%H/_
*,
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table J.2 Requirements for the results of tensile tests
Pipe grade
Pipe body of SMLS and welded pipesWeld seam of HFW and SAW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table J.2 Requirements for the results of tensile tests (continued)
Pipe grade
Pipe body of SMLS and welded pipesWeld seam of HFW and SAW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
J.6 Tolerances for diameter, wall thickness, length and straightness
J.6.1 #?!'*3%"&&"!M3
J.6.2 !!M;
J.6.3 Q%"4*%43@,+""!%"!"!=?""Q%!"!!!44%,
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table J.3 Tolerances for diameter and out-of-roundness
diameter
D
mm (in)
Diameter tolerances d
mm (in)
Out-of-roundness tolerances
mm (in)
Pipe except the end Pipe end%%! Pipe except the end
Pipe end%%!
SMLS pipe Welded pipe SMLS pipe Welded pipe
6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table J.4 Tolerances for wall thickness
Wall thickness
t
mm (in)
Tolerances
mm (in)
SMLS pipe
;%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
@ $>
P?!"
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
No Type of inspection Type of pipe Frequency of inspection
11%"!&H/_
HK8%/8%D: /
12 "&&"pipe with D 465%3
66*- D:%HK8%/8!"100 lengths of pipe
13 "&&"pipe with D 465%3
66*- D:%HK8%/8!"20 lengths of pipe
14 Non-destructive inspection D:%HK8%/8 !!!/?
4-%"%'):36
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table J.7 Number, orientation and location of test pieces per sample for mechanical tests
Type of pipe Sample location Type of test
Number, orientation and location of test pieces per sample
D
mm (in)
*4@%456*- *4@%456*--
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
J.8.3.2 Hardness test
J.8.3.2.1 H"N!!!!6-
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Dimensions in millimetres (inches)
b) SAW pipe
c) HFW pipe Weld centreline.b
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
J.8.3.2.2 H!D:K"M4%?!
t ;%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex K
Non-destructive inspection for pipe ordered for sour service and/or
offshore service
K.1 General
? "!!\,*!--(H* ^ K "! % &"! ! /? # % ?! !=!
=?
K.2 General non-destructive inspection requirements and acceptance criteria
K.2.1 Laminar imperfections at the pipe ends
K.2.1.1 :!6%;
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
K.3 Non-destructive inspection of SMLS pipe
K.3.1 Ultrasonic inspection for longitudinal imperfections
D:"&"!!!"!!!! 4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table K.1 Acceptance criteria for laminar imperfections
Service condition
Maximum individual imperfection
Minimum imperfection size considered
Maximum population densityArea
mm2 (in2)
Length
mm (in)
Area
mm2 (in2)
Length
mm (in)
Width
mm (in)
Pipe body (or strip/plate body)
Offshore 4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
K.4.4 Supplementary non-destructive inspection
%HK8!!"!""!!!!4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
K.5.1.3 K$%""!!"!"!"!!!-44
%&$%!"/8:!/8H%"$!!!!!!'"#;
K.5.2 Laminar imperfections in the pipe body and on the strip/plate edges
K.5.2.1 ("!!!!!!!4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex L
Steel designations
:4"!""#"
Table L.1 List of corresponding additional steel designations (steel numbers) for use in Europe
Steel name in accordance with ISO 3183
Steel number in accordance with EN 10027-2[22]
Steel grades for PSL 1 pipe in Table 4
:4,- 1.8700
:4,- 1.8707
L210 1.8713
:*;- 1.8723
L290 1.8728
L320 1.8729
:36< 1.8730
L390 1.8724
:;4- 45,*-
:;-< 45,*6
:;5- 1.8727
Steel grades for PSL 2 pipe in Table 5
:*;-F 1.8788
L290R 1.8789
:*;-E 1.8790
L290N 1.8791
L320N 1.8792
:36
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table L.1 (continued)
Steel name in accordance with ISO 3183
Steel number in accordance with EN 10027-2[22]
Steel grades for PSL 2 pipe in Table 5
:;-
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table L.1 (continued)
Steel name in accordance with ISO 3183
Steel number in accordance with EN 10027-2[22]
Steel grades for PSL 2 pipe for offshore service in Table J.1
:*;-E 1.1040
L290NO 1.1041
L320NO 1.1042
:36
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Annex M
PSL 2 pipe ordered for European onshore natural gas transmission
pipelines
M.1 General
? != : * #" "
M.2 Additional information to be supplied by the purchaser
!=,4!!=,*%"!!!!=!>
"$!%!>
4 !!!t *-%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
6 !+"9:;4-E#}6
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
M.3.3.2 Welded pipe
M.3.3.2.1 Q%!""!"!""!"!/8H%/8:%'8H%'8:%HK8ED!3
K HK8 & !% ! ! !!3"
M.3.3.2.2 KHK8%"!%!"!!
M.3.3.2.3 %!!%!!(%"!!3
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table M.1 Chemical composition for pipe with t 25,0 mm (0.984 in)
Steel grade
(Steel name)
Mass fraction, based upon heat and product analyses
.?"
Carbon equivalent c
.?"
Carbon equivalent c
.?"
C b Si Mn b P S V Nb Ti Other CEIIW CEPcmSeamless and welded pipe
:*;-E#GE#
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table M.2 Requirements for the results of tensile test t 25,0 mm (0.984 in)
Steel grade
Pipe body of SMLS and welded pipes
Weld seam of HFW, SAW
and COW pipes
Yield strength
R
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
M.5 Tolerances for diameter, wall thickness, length, and straightness
M.5.1 #?!'*3%"&&"!4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table M.4 Tolerances for wall thickness
Wall thickness
t
mm (in)
Tolerances
mm (in)
SMLS pipe b
;%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Table M.5 Maximum permissible radial offset for SAW and COW pipe
p1 p2 pi p \,*^4-
"""p1 p2 #+"4-"!#+"4*
P.6 Hydrostatic test pressure for threaded and coupled pipe10)
!"!"&%?! " +" " "=! " !" "=!"!E1!!"'"-
"" "&*6%5
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
P.8 Background on CVN specimen sizes12)
P.8.1 Calculations for minimum wall thickness for standard Charpy V-notch specimens
'"5+""!!!4
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
P.8.2 Calculations for minimum wall thicknesses for tapered Charpy V-notch specimens
Figure P.4#+"*
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
=
D D2 2
27 52
2
12
( , ) (P.20)
or
=
D D2 2
1 0832
2
12
( . ) (P.21)
=
D D2 2
14 02
2
12
( , ) (P.22)
or
=
D D2 2
0 5512
2
12
( . ) (P.23)
D"!!!'N&E!!t%4 t%*!"="!%
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
Bibliography
\4^ /D#*@&%=`!% 13)
\*^ ( *@
-
BS EN ISO 3183:2012
ISO 3183:2012(E)
\*
-
BS EN ISO 3183:2012
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
This page deliberately left blankCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
This page deliberately left blankCopyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---
-
BSI is the independent national body responsible for preparing British Standards and other standards-related publications, information and services. It presents the UK view on standards in Europe and at the international level.
BSI is incorporated by Royal Charter. British Standards and other standardisation products are published by BSI Standards Limited.
British Standards Institution (BSI)
raising standards worldwide
BSI
389 Chiswick High Road London W4 4AL UK
Tel +44 (0)20 8996 9001Fax +44 (0)20 8996 7001www.bsigroup.com/standards
RevisionsBritish Standards and PASs are periodically updated by amendment or revision. Users of British Standards and PASs should make sure that they possess the latest amendments or editions.
It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using British Standards would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside frontcover. Similary for PASs, please notify BSI Customer Services.
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001
BSI offers BSI Subscribing Members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of British Standards and PASs.
Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: [email protected]
Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website www.bsigroup.com/shop.In addition all orders for BSI, international and foreign standards publicationscan be addressed to BSI Customer Services.
Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: [email protected]
In response to orders for international standards, BSI will supply the British Standard implementation of the relevant international standard, unless otherwise requested.
Information on standardsBSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.
Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: [email protected]
BSI Subscribing Members are kept up to date with standards developments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Administration.
Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: [email protected]
Information regarding online access to British Standards and PASs via British Standards Online can be found at www.bsigroup.com/BSOLFurther information about British Standards is available on the BSI website at www.bsi-group.com/standards
CopyrightAll the data, software and documentation set out in all British Standards and other BSI publications are the property of and copyrighted by BSI, or some person or entity that own copyright in the information used (such as the international standardisation bodies) has formally licensed such information to BSI for commerical publication and use. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Department.
Tel: +44 (0)20 8996 7070Email: [email protected]
Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Jacobs Enterprise Wide/3219500143, User=Minero, OyukiPamela
Not for Resale, 04/08/2015 07:14:39 MDTNo reproduction or networking permitted without license from IHS
--```,``,```,````,,``,,``,,`,``-`-`,,`,,`,`,,`---