The Extron® ISM HDSDI is a universal video and RGB scaler board with HDSDI output for the ISM 824. It has a single BNC connector and a local audio

output. The board mounts in one of the four vertical expansion slots (numbered 1 to 4) at the rear of the ISM 824. Refer to the ISM 824 User Guide, available at www.extron.com.

To install an ISM HDSDI output board in the ISM 824 base unit:

1. Turn off the ISM 824. Remove the power cord. Repeat for all connected devices.

2. Select an open slot at the rear, or take out a blank plate by removing the two retaining screws (top and bottom), and lifting the plate away.

NOTE: Retain and reuse the screws to secure the new output board in place. Retain the blank plates. If a board is already installed in the desired slot, remove the screws and carefully pull out the board.

3. Holding the new board by the frame, align the front (non-connector end) of the board with the top and bottom plastic guides in the ISM 824. Slide the board in carefully, keeping within the guides. Push it into place firmly, and secure it with the retained screws.

4. If required, repeat steps 2 through 4for any other output boards.

5. Power on the ISM 824. The new output board(s) is autodetected, and takes approximately 30 seconds to initialize. The 16 character LCD display indicates the new board type, slot used, and counts down the initialization time. See inset for example display of a new ISM HDSDI board installed in slot #2, with 16 seconds left.

6. Connect a suitable display device to the BNC connector. The output can be configured via the front panel (see page 2) or by SIS™ commands (see page 3).

7. Insert a 5-pole captive screw connector into the local audio output connector for balanced or unbalanced stereo output. Wire the connector as shown below.

1

100-24050/60 H

z

1.2A MAX.

1

2

3

4

5

6

7

8

2

1

2

3

4

5

6

7

8

1

2

1

INPUTS

OUTPUTS

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

R/R-Y

G/Y

VID

B/C

B-Y

H/HV

V

PASS THRU

INPUTS

RESET

LA

NR

EM

OT

E

RS

232/

RS

422

AC

TL

INK

OUTPUT

VIDEO

SCALER

70-545-01

3 R/

R-Y

G/Y

B/

B-Y

H/

HV

V

OUTPUT

UNIV.

SCALER

70-544-01

5 R/

R-Y

G/Y

B/

B-Y

H/

HV

V

OUTPUT

PASS

THRU

70-547-01

8 R/

R-Y

G/Y

B/

B-Y

H/

HV

V

ExtronISM 824Integration ScalingMatrix Switcher

Align output boardwith top and bottomplastic guides.

R/

R-Y

G/Y

B/

B-Y

H/

HV

V

OUTPUT

7

SCAN

CONV.

70-546-01

Example Output Board Installation

NOTE: X! = Input number, 0-8X@ = Output number, 1-8X1) = Mode status, 1 = on, 0 = offX2) = Test pattern, 00 = off, 01 = color bars, 02 = 4:3/16:9 crosshatch, 03 = 4x4 crosshatch, 04 = split gray scale, 05 = ramp, 06 = alternating pixels, 07 = crop, 08 = 1.33 aspect, 09 = 1.78 aspect, 10 = 1.85 aspect, 11 = 2.35 aspectX2! = Output resolution, 17 = 720p, 18 = 1080i, 19 = 1080p X2@ = Refresh rate, 1 = 50 Hz, 2 = 60 Hz, 7 = 24 Hz, 8 = 25 Hz, 9 = 30 Hz, 10 = 59.94 HzX5% = Aspect ratio, 1 = 16:9, 0 = 4:3

ISM HDSDI Output Board • Setup Guide

New Univ HDSDISlot #2 16

ISM HDSDI

HD

SD

IU

NIV

ER

SA

LS

CA

LER

HDSDI

L R

Unbalanced Stereo OutputBalanced Stereo Output

TipRing

Sleeve(s)Tip

Ring

LR

Left

Right

Tip

Sleeve(s)Tip

LR

Left

RightNO GROUND HERE.

NO GROUND HERE.

CAUTION: For unbalanced audio, DO NOT connect the sleeves to the negative contacts. Connect to center ground contact.

ISM HDSDI Output Board • Setup Guide, cont’d

ISM HDSDI Configuration MenuUsing the front panel menu buttons (Menu and Next), the ISM HDSDI configuration menu can be accessed. From the Output Configuration screen, press Next until reaching the #x Univ HDSDI menu (see the image below). Press Menu and Next to navigate through the menus and use the front panel Adjust knobs ({ [), to change the settings as desired. Refer to the ISM 824 User Guide, online at www.extron.com for full details.

From the default cycle press Menu repeatedly to reach the Output Configuration menu. Press Next (enters Select Output menu) and rotate either Adjust knob to select the Univ HDSDI menu. Follow the figure below to enter each menu and use the Adjust knobs to change the value.

Select Output#8 Univ HDSDI

Next

Input Setup#8 Univ HDSDI

Aspect Ratio4:3

Next

Rotate either knobto select Aspect Ratio (4:3 or 16:9).

Next

H Start V128 128

Rotate knob to adjust H(orizontal) start. Rotate knob toadjust V(ertical) start.

Next

Total Pix Phase1728 00

Rotate knob to adjust Total Pix value.Rotate knob toadjust Phase value. .Next

H Active V1283 1028

Rotate knob to adjust H active value.Rotate knob toadjust V active value.

Menu

Next

Output Config#8 Univ HDSDI

Rotate knob to adjust resolution. Rotate knob toadjust refresh rate.

Next

1080i 60 HzResolution

Next

Menu

User Presets#8 Univ HDSDI

30 sec.

<NA> 1 2 3Save Preset

Next

Rotate either knobto select a preset to save current settings.

<NA> 1 2 3Erase Preset

Next

Rotate either knobto select a presetto erase.

Advanced Config#8 Univ HDSDI

Next

NoneTest Pattern

Rotate either knobto select a test pattern.

<Off> OnBlue Mode

Next

Rotate either knobto turn blue mode Onor Off.

Next

Off <On>Film Mode

Rotate either knobto turn film mode Onor Off.

Next

Menu

Next

Next

Rotate knob to select input.Rotate knob toturn On or Off.

Input #2 OffAuto Image

Auto Memory

Next

Rotate either knobto turn auto memories On or Off.

Off <On>

Input #2 OffFull Screen

Rotate knob to select input.Rotate knob toturn On or Off.

Next

NOTE: Within any submenu, press the Menu buttonto go directly to the top level (Output Card Configuration) menu. If, for 30 seconds, no button is pressed or Adjust knob is rotated,the menu times out and reverts to the defaultdisplay cycle.

Input Setup

The Input Setup submenu allows configuration of aspect ratio, horizontal and vertical start points, total pixels and phase value, and active horizontal and vertical areas. Rotate the Adjust knobs as required to change values.

MENU NEXT

ADJUST

2

Output Config

The Output Config submenu displays and allows changes to be made to the resolution and refresh rate. Use the Adjust knobs to select a resolution and refresh rate.

Resolution 24 Hz 25 Hz 30 Hz 50 Hz 59.94 Hz 60 Hz

720p X X X X X X

1080i X X X

1080p X X X

User Presets

The User Presets submenu displays and allows the current settings to be saved as a preset, or to erase an existing saved preset. Use the Adjust knobs to select between the presets.

Advanced Config

Within this submenu the following settings can be adjusted: auto image (on or off), test pattern (selection), blue mode (on or off), auto memories (on or off), film mode (on or off), and full screen (on or off).

Test Pattern

The test pattern submenu offers the following test patterns to choose from:

Color Bars Split Grayscale4x4 Crosshatch AlternatingPixels

4:3/16:9Crosshatch

1.78 Aspect 1.85 Aspect 2.35 Aspect1.33 AspectCrop

Ramp

3

NOTE: X! = input number, 0-8X@ = output number, 1-8

SIS commands and definitions continue on page 4.

Board-specific SIS CommandsThe ISM HDSDI board can be configured with specific Simple Instruction Set™ (SIS) commands. The table below and on page 4 lists some of the ISM HDSDI board specific commands. Refer to the ISM 824 User Guide, at www.extron.com for a list.

Command ASCII Command (host to ISM)

Response(ISM to host)

Additional Description

Input selection

Video and audio X!*X@! OutX@•InX!•All] Tie video/audio input X! to X@.

Video X!*X@& OutX@•InX!•RGB] Select video input X! to X@.

Audio X!*X@$ OutX@•InX!•Aud] Select audio input X! to X@.

Extron USA - West Headquarters

+800.633.9876Inside USA / Canada Only

+1.714.491.1500+1.714.491.1517 FAX

Extron USA - East

+800.633.9876Inside USA / Canada Only

+1.919.863.1794+1.919.863.1797 FAX

Extron Europe

+800.3987.6673Inside Europe Only

+31.33.453.4040+31.33.453.4050 FAX

Extron Asia

+800.7339.8766Inside Asia Only

+65.6383.4400+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655+81.3.3511.7656 FAX

Extron China

+400.883.1568Inside China Only

+86.21.3760.1568+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800+971.4.2991880 FAX

68-1123-65Rev A08 10© 2010 Extron Electronics. All rights reserved. www.extron.com

4

Command ASCII Command (host to ISM)

Response(ISM to host)

Additional Description

Output scaler rate

Set output rate X@ * X2!* X2@= RteX@ *X2!*X2@] Set resolution/refresh rate.

View X@= X2!*X2@] View selected output rate.

Start auto image

Start auto image 14*X@# ImgX@] Auto image input tied to X@.

Auto memoryOn X@*1M X@Aut1] Set auto memory to on.

Off X@*0M X@Aut0] Set auto memory to off.

View setting X@M X1)] View current auto memory.

Auto image

Enable 55*X@* X!*1# X@ImgX!*1] Enables auto image for all inputs.

Disable 55*X@* X!*0# X@ImgX!*0] Disables auto image.

View 55*X@* X!# X1)] View auto image setting.

Input aspect ratio

16:9 9*X@*1# X@AspX!*1] Set input aspect ratio to 16:9.

4:3 9*X@*0# X@AspX!*0] Set input aspect ratio to 4:3.

View 9*X@# X5%] View current aspect ratio.

Full screen

Enable 99*X@*X!*1# X@FulX!*1] Enables full screen view.

Disable 99*X@*X!*0# X@FulX!*0] Disables full screen view.

View 99*X@*X!# X1)] View the current on/off status.

Test pattern

On X@*X2) J X@TstX2)] Select test pattern.

View X@ J X2)] View the test pattern selected.

NOTE: X! = Input number, 0-8X@ = Output number, 1-8X1) = Mode status, 1 = on, 0 = offX2) = Test pattern, 00 = off, 01 = color bars, 02 = 4:3/16:9 crosshatch, 03 = 4x4 crosshatch, 04 = split gray scale, 05 = ramp, 06 = alternating pixels, 07 = crop, 08 = 1.33 aspect, 09 = 1.78 aspect, 10 = 1.85 aspect, 11 = 2.35 aspectX2! = Output resolution, 17 = 720p, 18 = 1080i, 19 = 1080p X2@ = Refresh rate, 1 = 50 Hz, 2 = 60 Hz, 7 = 24 Hz, 8 = 25 Hz, 9 = 30 Hz, 10 = 59.94 HzX5% = Aspect ratio, 1 = 16:9, 0 = 4:3

ISM HDSDI Output Board • Setup Guide, cont’d