ISLAVSEVAL1Z User Guide - · PDF fileNote: Hibernate Module will not be used ... TP2 R24 0E...
-
Upload
truongtuong -
Category
Documents
-
view
218 -
download
3
Transcript of ISLAVSEVAL1Z User Guide - · PDF fileNote: Hibernate Module will not be used ... TP2 R24 0E...
USER’S MANUAL
UG089Rev 0.00
August 22, 2016
ISLAVSEVAL1ZUSB to AVSBus™ Adapter User Guide
The Intersil USB to AVSBus Adapter (often referred to as a “dongle”) is used to connect a demonstration board with a AVSBus interface to a PC. The USB to AVSBus adapter is powered from the USB output of the host PC. The USB interface utilizes the USB Mini format, and the output uses a standard 2 row, 6-pin header on 0.100 inch centers. The AVSBus command set is accessed by using the PowerNavigator™ evaluation software from a PC running Microsoft Windows. The PowerNavigator software is downloaded from the Intersil website using the following link:http://www.intersil.com/powernavigator.html
The USB to AVSBus adapter can be used to communicate with Intersil’s AVSBus enabled devices at clock rates from 5MHz to 50MHz and at VDDIO voltage levels from 1V to 3.3V. The VDDIO voltage is generated within the USB to AVSBus adapter. The USB to AVSBus adapter can also store up to 100 instructions for continuous multi-command testing purposes.
USB to AVSBus Adapter Quick Start Guide• Connect the USB Mini provided between the host computer
and the USB to AVSBus adapter
• Connect USB to AVSBus adapter to demonstration board to test or evaluate
• Apply input power to the demonstration board
• Configure the demonstration board for AVSBus operation using the USB to PMBus adapter and PowerNavigator™
• Navigate to the AVSBus control page in PowerNavigator™ and evaluate the AVSBus functionality
Technical DetailsA typical application set-up is shown in Figure 1. For those wishing to make discrete connections to an application board, a pictorial diagram of the output pin signals is shown in Figure 2. A schematic of the USB to AVSBus Adapter internal circuitry is provided in Figure 3. The Bill Of Materials (BOM) is detailed on page 3.
.
Ordering InformationPART NUMBER DESCRIPTION
ISLAVSEVAL1Z USB to AVSBus adapter and cable
FIGURE 1. USB TO AVSBus TYPICAL SET-UP
FIGURE 2. PIN CONFIGURATION DIAGRAM
TO HOST PC
VIN SUPPLY
AVS_CLKAVS_MDA
VDDIO
GNDAVS_SDANOT USED
UG089 Rev 0.00 Page 1 of 6August 22, 2016
UG
089R
ev 0.00P
age 2 of 6A
ugu
st 22, 20
16
ISLA
VS
EV
AL1Z
1
1
D
C
B
A
VDDIO GENERATION
AVS BUS INTERFACETOR
Test Points forJTAG/SWD debugger and UART interface
Layout Note:Place PESD5V0U4BW close to AVSBus connector without via.
AVS
MOUNTING HOLE
AVS_SPI_MISO
AVS_GPIO
DAC_LDO_ADJ
TMSTCK
TDITDO
RST_N
UART0_TXUART0_RX
AVS_SPI_CLK
DAC_OUT
AVS_VDDIO_SENSE
AVS_SPI_MOSI
_MOSI
AVS_SPI_CLK
AVS_SPI_MOSI
_MISO
_CLK
T_EN
DGND
AVS_VDDIO_POWER
VBUS
DGND
DGND
VDDIO_LOCAL
DGND
DGND
DGND
VCC_3V3
DGND
DGND
DGND
DGND
DGND
AVS_VDDIO_POWER
VCC_3V3
AVS_VDDIO_POWER
AVS_VDDIO_POWER
DGND
VCC_3V3
DGND
D
AVS_VDDIO_POWER
DGND
Title
Size
Project
Rev
Date: ofSheet
Designed for Intersil by eInfochips
eInfochips#: 2.0
USB,MCU,SPI,AVS CONN
D
3 4Tuesday, August 18, 2015
16_00258_02
AVS_Master_Dongle
Title
Size
Project
Rev
Date: ofSheet
Designed for Intersil by eInfochips
eInfochips#: 2.0
USB,MCU,SPI,AVS CONN
D
3 4Tuesday, August 18, 2015
16_00258_02
AVS_Master_Dongle
Title
Size
Project
Rev
Date: ofSheet
Designed for Intersil by eInfochips
eInfochips#: 2.0
USB,MCU,SPI,AVS CONN
D
3 4Tuesday, August 18, 2015
16_00258_02
AVS_Master_Dongle
TP2
R1866.5k
TP5
TP8
R39
1K 1%
C52
100nF25V
R6810K
R40
1K 1%
R13
95.3k
MT3
163MIL NPTH HOLE
C45
100nF25V
TP11
R51
TBDDNP
C13
1uF25V
C31
TBDDNP
R16294k
TP7
TP6
U9
PESD5V0U4BW,115
11 22 33
44
55
TP3
MT1
163MIL NPTH HOLEC39
4.7uF25V
C10
100nF25V
TP4
R41 0E
R38
10KDNP
MT4
163MIL NPTH HOLE
R14
100K
R31 100EDNP
C1210uF10V
C33
100nF25V
C32
100nF25V
DNP
MT2
163MIL NPTH HOLE
C4
100nF25V
U7
TPS76201
FB4
GN
D2
IN1
EN3
VOUT5
R53
TBDJ2
SSW-103-02-G-D-RA
123456
TP10
R50
10K
ISLAVSEVAL1Z Schematic
FIGURE 3. USB TO AVSBus ADAPTER SCHEMATIC
5
5
4
4
3
3
2
2
D
C
B
A
USB, MCU, SPI, AVS CONNECTOR
Note: Hibernate Module will not be used
Note: Ethernate Module will not be used
Note:SSI Legacy Mode: Freescale SPIUse system clock as clock source for SPI Clock
LED Indicators:State: Green blink, Red off---good traffic State: Green on, Red off---power good, no traffic State: Green off, Red blink---bad traffic (SlaveAck is not good)
Layout Note:Place EMI2121 close to USB Mini-Bconnector without via.
For better routing IN_1+/OUT_1+ andIN_1-/OUT_1- are connected to DM andDP respectively.
Note:USB controller should be configured asDevice and USB0ID should be configured asGPIO input.
USB 2.0 HIGH SPEED INTERFACE
MCU POWER, RESET & CLOCK
MCU AVS BUS LEVEL TRANSLA
Note:PD7 is NMI capable GPIO
Layout Note:Place level translators close toBus connector.
Layout Note:Place C23,C22 and, C21/C20 close to Pin 115 and C20/C21 at Pin 87.
Note:Analog switch (2X1 mux/demux) provided toselect VDDIO_LOCAL / AVS_GPIO.
8-BIT Slave Address: 1100000R/Wb
8-BIT Slave Address: 1010000R/Wb
Note: RHEOSTAT MODE (RW and RH with RL not connected)
VFB
PC_USB_D+PC_USB_D-
VBAT
WAKE_N
HIB_NRST_N
SSI_SPI_CLKSSI_SPI_MOSISSI_SPI_MISO
SSI0FSS
XOSC0
OSC0
OSC1
UART0_TX
GPIO_GRN_LEDGPIO_RED_LED
MCU_USB_D+MCU_USB_D-
DAC_I2C0_SCLDAC_I2C0_SDA
PC_USB_ID
PC
_US
B_ID
USB_ID
TCKTMSTDITDO
DAC_I2C0_SCLDAC_I2C0_SDA
DAC_OUT
RBIAS
VREF
UART0_RX
PC_USB_D+PC_USB_D-
MCU_USB_D+MCU_USB_D-
AVS_VDDIO_LOCAL_EN_N
AVS_VDDIO_LOCAL_EN_N
SCLSDA
AV
S_G
PIO
AVS_GPIO_SENSE
VDDIO_OUT_EN
AVS_VDDIO_SENSE
VDDIO_OUT_EN
AVS_GPIO_SENSE
AVS_GPIO
S_ENT_EN
AVS_SPI
DAC_I2C0_SDADAC_I2C0_SCL
SSI_SPI_CLK
SSI_SPI_MOSI
AVS_SPI_CLK_1V
AVS_SPI_MOSI_1V
SSI_SPI_MISO AVS_SPI
AVS_SPI
S_EN
DGNDDGND
DGND
VBUS VCC_3V3
DGND
DGND
DGNDDGND
DGND
VCC_3V3
DGND
VCC_3V3
VCC_3V3
DGND
DGND
DGND DGND
VCC_3V3
DGND
VBUSVCC_3V3
DGND
VCC_3V3
VBUS
VCC_3V3
DGND
DGND DGND
VCC_3V3
DGND
DGND
VCC_5V
DGND
DGND
DGND
VCC_5V
DGNDDGND
DGND
DGND
VDDIO_LOCAL
DGND
VBUS
DGND
DGND
DGND
VDDC
VREFA
DGND
DGND
DGND
DGND
DGN
DGND
DGND
VCC_3V3
VCC_3V3
DGND
DGND
DGNDDGND
VCC_3V3
VCC_3V3
R4
100E
R240E
C47
1uF25V
U4
EMI2121MTTAG
IN_1+1
IN_1-2
VDD/ID6
OUT_1-7OUT_1+8
GND13
GND24
GND35
GND49
C37
100nF25V
D2LED GRN
U2C
TM4C1294NCPDT-128-TQFP
VDD1351
VDD1452
GND555
GND658
EN0TXOP57
EN0TXON56
EN0RXIP54
EN0RXIN53
RBIAS59
R75 0E
R44
1K 1%
C20
100nF25V
R46 0E
R6
2.2K
U5
NLSV2T244MUTAG
VCCA1
VCCB8
A12
A23B1
7
B26
GND5
OE4
D3
BZX84C3V3S
3C2
1 NC
2 A2
4NC1
5A1
6C1
C43
100nF25V
C34
100nF25V
U10 TS5A3160DCKR
NO1
IN6
NC3
4COM
VCC5
GND2
R17 0E
R73
0E
R54
3301%
C27
12pF50V
R23
0E
R52
10K DNP
C19
100nF25V
C29
100nF25V
R1 52.3K,1%
C50
12pF50V
C17
100nF25V
U1
TPS73701DRBR
IN8
EN5
OUT1
FB3
GND4
NC12
NC26
NC37
PAD9
R8 10K
R22 2K
R20
51E
C8 100nF25V
C53
100nF25V
TP9
R42 0E
C15
100nF25V
SW1
SN74CB3Q3306ADCUR
1OE1
1A2
1B3
GND4
2A5
2B6
2OE7 VCC
8
U12
NLSV4T244MUTAG
VCCA1
VCCB11
A12
A23 B1
10
B29
GND6
OE12
A34
A45 B3
8
B47
R254.87K
C23
2.2uF16V
R12330E
12
R150EDNP
R43 0E
C14
100nF25V
C5
4.7uF25V
C3
100nF25V
R7
2.2K
R27
100E
TP1
C6
100nF25V
C26
12pF50V
C41
100nF25VC16
100nF25V
R6110K
R47 0E
C40
1uF25V
C22
1uF25V
C51
12pF50V
R74
0E
R1910K
R3
30.1K,1%
C2
1uF25V
Y1
25MHz
14 3
2
F1 Fuse
R48
10K
R72 0E
D1RED LED
C36
100nF25V
C18
100nF25V
C25
1uF25V
R65
330 1%
C48
100nF25V
C1
100nF25V
C21
100nF25V
R45
1K 1%
C42
4.7uF25V
R28 0E
U8
MCP4706A0T-E/CH
VDD3
VOUT1
SCL5
SDA4
VREF6
VSS2
R56
3301%
U11
ISL23325WFRUZ-T7A
SDA1
SCL2
A03
A14
A25
GND16
NC7
RL013
RH011
GND215
VCC14
RW012
VLOGIC16
RW19
RL18
RH110
R70 0E
R2
100EDNP
U2B
TM4C1294NCPDT-128-TQFP
RST70
OSC189
XOSC167
GND117
GND248
GND380
GND4114
VBAT68
HIB65
WAKE64
VREFA+9
VDDA8
VDD17
VDD216
VDD326
VDD428
VDD539
VDD647
VDD769
VDD879
VDD990
VDD10101
VDD11113
VDD12122
VDDC187
VDDC2115
OSC088
XOSC066
GNDA10
C24
100nF25V
R64
330 1%
J1
UX60-MB-5ST
VCC1
D-2D+3
GND5
SH17
SH26
ID4
SH38
SH49
R9 10K
R11330E
12
C35
100nF25V
U2A
TM4C1294NCPDT-128-TQFP
PG049
PG150
PJ0116
PJ1117
PL081
PL182
PL283
PL384
PL485
PL586
PN0107
PN1108
PN2109
PN3110
PN4111
PN5112
PQ05
PQ16
PQ211
PQ327
PQ4102
PF042
PF143
PF244
PF345
PF446
PH029
PH130
PH231
PH332
PM078
PM177
PM276
PM375
PM474
PM573
PM672
PM771
PP2103
PP3104
PP4105
PP5106
PA0/U0RX33PA1/U0TX34
PA2/SSI0CLK35
PA3/SSI0FSS36
PA4/SSI0XDAT037
PA5/SSI0XDAT138
PA640PA741
PB0/USB0ID95
PB1/USB0VBUS96
PB2/I2C0SCL91
PB3/I2C0SDA92
PB4/AIN10121
PB5/AIN11120
PD0/AIN151
PD1/AIN142
PD2/AIN133
PD3/AIN124
PD4/AIN7125
PD5/AIN6126
PD6/AIN5127
PD7/AIN4128
PC0/TCK/SWCLK100
PC1/TMS/SWDIO99
PC2/TDI98
PC3/TDO/SWO97
PC4/C1-25
PC5/C1+24
PC6/C0+23
PC7/C0-22
PE0/AIN315
PE1/AIN214
PE2/AIN113
PE3/AIN012
PE4/AIN9123
PE5/AIN8124
PK0/AIN1618
PK1/AIN1719
PK2/AIN1820
PK3/AIN1921
PL6/USB0DP94
PL7/USB0DM93
PP0/C2+118
PP1/C2-119
PK760 PK661 PK562 PK463
C9
100nF25V
ISLAVSEVAL1Z
Bill of MaterialsITEM QTY REFERENCE MANUFACTURER PART VALUE DESCRIPTION PACKAGE MANUFACTURER
1 28 C1, C3, C4, C6, C8, C9, C10, C14, C15, C16, C17, C18, C19, C20, C21, C24, C29, C33, C34, C35, C36, C37, C41, C43, C45, C48, C52, C53
C1005X5R1E104K050BC 100nF CAP CER 0.1µF 25V 10% X5R 0402
402 TDK Corporation
2 6 C2, C13, C22, C25, C40, C47
GRM188R61E105KA12D 1µF CAP CER 1µF 25V 10% X5R 0603
603 Murata
3 3 C5, C39, C42 CL10A475MA8NQNC 4.7µF CAP CER 4.7µF 25V 20% X5R 0603
603 Samsung
4 1 C12 TPSA106K010R0900 10µF CAP TANT 10µF 10V 10% 1206
1206 AVX Corporation
5 1 C23 CE EMK107 BJ225KA-T 2.2µF CAP CER 2.2µF 16V 10% X5R 0603
603 Taiyo Yuden
6 4 C26, C27, C50, C51
CC0402JRNPO9BN120 12pF CAP CER 12PF 50V 5% NPO 0402
RC0402 Yageo
7 1 C31 DNP DNP DNP 603 TDK Corporation
8 1 C32 C1005X5R1E104K050BC 100nF CAP CER 0.1µF 25V 10% X5R 0402
402 TDK Corporation
9 1 D1 LTL-4221N RED LED LED 3mm HI-EFF RED DIFFUSED
Round with Domed Top, 3mm
Lite-On Inc.
10 1 D2 LTL-4231N LED GRN LED 3mm GREEN DIFFUSED
Round with Domed Top, 3mm
Lite-On Inc.
11 1 D3 BZX84C3V3S-7-F BZX84C3V3S DIODE ZENER ARRAY 3.3V SOT363
SOT-363 Diodes Incorporated
12 1 F1 0603L100SLYR Fuse PTC RESETTBLE 6V 1.0A LOW-R 0603
603 Littelfuse Inc.
13 1 J1 UX60-MB-5ST UX60-MB-5ST CONN RECEPT MINI USB2.0 5POS
SMT Hirose
14 1 J2 SSW-103-02-G-D-RA SSW-103-02-G-D-RA CONN RCPT 0.100" 6POS DL R/A GOLD
Through-hole Samtec Inc.
15 4 MT1, MT2, MT3, MT4
NA 163MIL NPTH HOLE 163 MOUNTING HOLE - 250 CLEARANCE
NA
UG089 Rev 0.00 Page 3 of 6August 22, 2016
ISLAVSEVAL1Z
16 1 R1 RC1005F5232CS 52.3k, 1% RES SMD 52.3kΩ 1% 1/16W 0402
Samsung Electro-Mechanics America, Inc.
17 2 R2, R31 ERJ-2RKF1000X 100Ω RES 100Ω 1/10W 1% 0402 SMD
402 Panasonic
18 1 R3 RC1005F3012CS 30.1k, 1% RES SMD 30.1kΩ 1% 1/16W 0402
Samsung Electro-Mechanics America, Inc.
19 2 R4, R27 ERJ-2RKF1000X 100Ω RES 100Ω 1/10W 1% 0402 SMD
402 Panasonic
20 2 R6, R7 RC0402JR-072K2L 2.2k RES 2.2kΩ 1/16W 5% 0402 SMD
402 Yageo
21 7 R8, R9, R19, R48, R50, R61, R68
ERJ-2RKF1002X 10k RES 10.0kΩ 1/10W 1% 0402 SMD
402 Panasonic - ECG
22 6 R11, R12, R54, R56, R64, R65
MCR01MZPF3300 330Ω RES 330Ω 1/16W 1% 0402 SMD
402 Rohm Semiconductor
23 1 R13 ERJ-2RKF9532X 95.3k RES SMD 95.3kΩ 1% 1/10W 0402
402 Panasonic Electronic Components
24 1 R14 ERJ-2RKF1003X 100k RES 100kΩ 1/10W 1% 0402 SMD
402 Panasonic
25 1 R15 ERJ-2GE0R00X 0E RES 0.0Ω 1/10W 0402 SMD
402 Panasonic
26 1 R16 RC1608F2943CS 294k RES SMD 294kΩ 1% 1/10W 0603
402 Samsung Electro-Mechanics America, Inc
27 14 R17, R23, R24, R28, R41, R42, R43, R46, R47, R70, R72, R73, R74, R75
ERJ-2GE0R00X 0E RES 0.0Ω 1/10W 0402 SMD
402 Panasonic
28 1 R18 RC1005F6652CS 66.5k RES SMD 66.5kΩ 1% 1/16W 0402
402 Samsung Electro-Mechanics America, Inc
29 1 R20 RC1005J510CS 51Ω RES SMD 51Ω 5% 1/16W 0402
402 Samsung Electro-Mechanics America, Inc
30 1 R22 RC1005F202CS 2k RES SMD 2kΩ 1% 1/16W 0402
402 Samsung Electro-Mechanics America, Inc
31 1 R25 RC1005F4871CS 4.87k RES SMD 4.87kΩ 1% 1/16W 0402
402 Samsung Electro-Mechanics America, Inc
32 2 R38, R52 ERJ-2RKF1002X 10k RES 10.0kΩ 1/10W 1% 0402 SMD
402 Panasonic - ECG
Bill of MaterialsITEM QTY REFERENCE MANUFACTURER PART VALUE DESCRIPTION PACKAGE MANUFACTURER
UG089 Rev 0.00 Page 4 of 6August 22, 2016
ISLAVSEVAL1Z
33 4 R39, R40, R44, R45
ERJ-2RKF1001X 1k RES 1kΩ 1/10W 1% 0402 SMD
402 Panasonic
34 1 R51 DNP DNP DNP 603 DNP
35 1 R53 DNP DNP DNP 402 DNP
36 1 SW1 SN74CB3Q3306ADCUR SN74CB3Q3306ADCUR
IC FET BUS SWITCH DUAL US8
US8 Texas Instruments
37 11 TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11
DNP Test Point TEST PAD TP-S40
--NA-- --NA--
38 1 U1 TPS73701DRBR TPS73701DRBR IC REG LDO ADJ 1A 8SON
8-SON Texas Instruments
39 1 U2 TM4C1294NCPDTI3 TM4C1294NCPDT-128-TQFP
IC MCU 32BIT 1024KB FLASH 128TQF
128-pin TQFP Texas Instruments
40 1 U4 EMI2121MTTAG EMI2121MTTAG IC FILTER COMMON-MODE ESD 8WDFN
WDFN8 ON Semiconductor
41 1 U5 NLSV2T244MUTAG NLSV2T244MUTAG IC XLATOR 2BIT NONINV DUAL 8UDFN
8-UDFN ON Semiconductor
42 1 U7 TPS76201DBVT TPS76201 IC REG LDO ADJ 0.1A SOT23-5
SOT-23-5 Texas Instruments
43 1 U8 MCP4706A0T-E/CH MCP4706A0T-E/CH IC DAC 8BIT NV EEP I2C SOT23-6
SOT-23-6 Microchip
44 1 U9 PESD5V0U4BW, 115 PESD5V0U4BW, 115
DIODE ARRAY ESD BI-DIR SOT-665
SOT-665 NXP Semiconductor
45 1 U10 TS5A3160DCKR TS5A3160DCKR IC SWITCH SPDT SC70-6
SC70 Texas Instruments
46 1 U11 ISL23325WFRUZ-T7A ISL23325WFRUZ-T7A
IC DGTL POT DUAL 10k 16UTQFN
16-UFQFN Intersil
47 1 U12 NLSV4T244MUTAG NLSV4T244MUTAG IC XLATOR 4BIT DUAL 12-UQFN
12-UQFN ON Semiconductor
48 1 Y1 NX3225GA-25.000M-STD-CRG-2 25MHz CRYSTAL 25.0000MHZ 8PF SMD
3.20mmx2.50mm NDK
Bill of MaterialsITEM QTY REFERENCE MANUFACTURER PART VALUE DESCRIPTION PACKAGE MANUFACTURER
UG089 Rev 0.00 Page 5 of 6August 22, 2016
http://www.renesas.comRefer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.1001 Murphy Ranch Road, Milpitas, CA 95035, U.S.A.Tel: +1-408-432-8888, Fax: +1-408-434-5351Renesas Electronics Canada Limited9251 Yonge Street, Suite 8309 Richmond Hill, Ontario Canada L4C 9T3Tel: +1-905-237-2004Renesas Electronics Europe LimitedDukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.KTel: +44-1628-651-700, Fax: +44-1628-651-804Renesas Electronics Europe GmbHArcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-6503-0, Fax: +49-211-6503-1327Renesas Electronics (China) Co., Ltd.Room 1709 Quantum Plaza, No.27 ZhichunLu, Haidian District, Beijing, 100191 P. R. ChinaTel: +86-10-8235-1155, Fax: +86-10-8235-7679Renesas Electronics (Shanghai) Co., Ltd.Unit 301, Tower A, Central Towers, 555 Langao Road, Putuo District, Shanghai, 200333 P. R. China Tel: +86-21-2226-0888, Fax: +86-21-2226-0999Renesas Electronics Hong Kong LimitedUnit 1601-1611, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong KongTel: +852-2265-6688, Fax: +852 2886-9022Renesas Electronics Taiwan Co., Ltd.13F, No. 363, Fu Shing North Road, Taipei 10543, TaiwanTel: +886-2-8175-9600, Fax: +886 2-8175-9670Renesas Electronics Singapore Pte. Ltd.80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre, Singapore 339949Tel: +65-6213-0200, Fax: +65-6213-0300Renesas Electronics Malaysia Sdn.Bhd.Unit 1207, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, MalaysiaTel: +60-3-7955-9390, Fax: +60-3-7955-9510Renesas Electronics India Pvt. Ltd.No.777C, 100 Feet Road, HAL 2nd Stage, Indiranagar, Bangalore 560 038, IndiaTel: +91-80-67208700, Fax: +91-80-67208777Renesas Electronics Korea Co., Ltd.17F, KAMCO Yangjae Tower, 262, Gangnam-daero, Gangnam-gu, Seoul, 06265 KoreaTel: +82-2-558-3737, Fax: +82-2-558-5338
SALES OFFICES
© 2018 Renesas Electronics Corporation. All rights reserved.Colophon 7.0
(Rev.4.0-1 November 2017)
Notice
1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation or any other use of the circuits, software, and information in the design of your product or system. Renesas Electronics disclaims any and all liability for any losses and damages incurred by
you or third parties arising from the use of these circuits, software, or information.
2. Renesas Electronics hereby expressly disclaims any warranties against and liability for infringement or any other claims involving patents, copyrights, or other intellectual property rights of third parties, by or
arising from the use of Renesas Electronics products or technical information described in this document, including but not limited to, the product data, drawings, charts, programs, algorithms, and application
examples.
3. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others.
4. You shall not alter, modify, copy, or reverse engineer any Renesas Electronics product, whether in whole or in part. Renesas Electronics disclaims any and all liability for any losses or damages incurred by
you or third parties arising from such alteration, modification, copying or reverse engineering.
5. Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The intended applications for each Renesas Electronics product depends on the
product’s quality grade, as indicated below.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic
equipment; industrial robots; etc.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control (traffic lights); large-scale communication equipment; key financial terminal systems; safety control equipment; etc.
Unless expressly designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas Electronics document, Renesas Electronics products are
not intended or authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems; surgical implantations; etc.), or may cause
serious property damage (space system; undersea repeaters; nuclear power control systems; aircraft control systems; key plant systems; military equipment; etc.). Renesas Electronics disclaims any and all
liability for any damages or losses incurred by you or any third parties arising from the use of any Renesas Electronics product that is inconsistent with any Renesas Electronics data sheet, user’s manual or
other Renesas Electronics document.
6. When using Renesas Electronics products, refer to the latest product information (data sheets, user’s manuals, application notes, “General Notes for Handling and Using Semiconductor Devices” in the
reliability handbook, etc.), and ensure that usage conditions are within the ranges specified by Renesas Electronics with respect to maximum ratings, operating power supply voltage range, heat dissipation
characteristics, installation, etc. Renesas Electronics disclaims any and all liability for any malfunctions, failure or accident arising out of the use of Renesas Electronics products outside of such specified
ranges.
7. Although Renesas Electronics endeavors to improve the quality and reliability of Renesas Electronics products, semiconductor products have specific characteristics, such as the occurrence of failure at a
certain rate and malfunctions under certain use conditions. Unless designated as a high reliability product or a product for harsh environments in a Renesas Electronics data sheet or other Renesas
Electronics document, Renesas Electronics products are not subject to radiation resistance design. You are responsible for implementing safety measures to guard against the possibility of bodily injury, injury
or damage caused by fire, and/or danger to the public in the event of a failure or malfunction of Renesas Electronics products, such as safety design for hardware and software, including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult
and impractical, you are responsible for evaluating the safety of the final products or systems manufactured by you.
8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. You are responsible for carefully and
sufficiently investigating applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive, and using Renesas Electronics
products in compliance with all these applicable laws and regulations. Renesas Electronics disclaims any and all liability for damages or losses occurring as a result of your noncompliance with applicable
laws and regulations.
9. Renesas Electronics products and technologies shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws
or regulations. You shall comply with any applicable export control laws and regulations promulgated and administered by the governments of any countries asserting jurisdiction over the parties or
transactions.
10. It is the responsibility of the buyer or distributor of Renesas Electronics products, or any other party who distributes, disposes of, or otherwise sells or transfers the product to a third party, to notify such third
party in advance of the contents and conditions set forth in this document.
11. This document shall not be reprinted, reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products.
(Note 1) “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its directly or indirectly controlled subsidiaries.
(Note 2) “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics.