IRISET122.252.230.113/content/labsheets/tel/telab/TE10hl.pdf · 2020. 10. 21. · 5-ISDN 6-DATA...
Transcript of IRISET122.252.230.113/content/labsheets/tel/telab/TE10hl.pdf · 2020. 10. 21. · 5-ISDN 6-DATA...
-
नाम Name ____________________________
अनुक्रमाांक Roll No. _______
पाठ्यक्रम Course __________________ प्राप्त अांक Marks Awarded
दिनाांक Date ______________ अनुिेशक का अध्य़ाक्षर Instructor’s Initial
04/05/2020 1
I R I S E T
Telephony Laboratory
Experiment No. TE - 10
इ रि से ट
टेलिफोनी प्रय़ोगशािा
प्रयोग संख्या टीई - 10
1. Purpose
To study Software Commands of Coral Flexicom 6000 Exchange. 2. Connectivity:
Connect the PI Terminal to the Exchange, 1. By Serial RS232 port of your computer with Serial port of Exchange on MCP card. Data cable is supplied by the vendor. 2. By dial-up modem to the modem port of DRCF card.
3. Open Hyper Terminal Application in your computer and do the terminal settings for Serial RS232 port. If you are using the dial-up modem, then provide the modem dial number in the connection window and get connect after dialing the number.
4. In the connection window, ' ENTER PASSWORD ' appears. After entering password root menu will be open.
5. Follow the below given Conventions in this lab sheet Screen captures are shown with 'courier new font'. Command proceeds with ' *: '. The default codes for DISPLAY are '1' & UPDATE '0'.
(ROOT)
NAME - IRISET
SAU # 39716
0-CONFIG
1-DIAGN
2-TABLES
3-ADMIN
4-ROUTING/COST
5-ISDN
6-DATA
7-CoraLINK
8-NETWORK
9-IP 10-HELP
To see help menu *: HELP
(HELP)
Description Command Description Command Description Command
CARD LIST CLIS CALL GROUP CALL NETWORK NODES NODE
PORT LIST PLIS DIGITAL RUNK DTDB SYS FEATURES SFE
FEAT.&AUTH. FEAT IST/SLT DEF. SLT SYS TIME SET-UP TIME
CLASS OF ERVICE COS KEY DEFINITION KEY TRUNK DEFINITION TRK
GROUPS GROUP KEY PROGRAMING PROG TRUNK GRP DEF TGDEF
NUMBERING PLAN NPL LCR/ROUTING LCR TRUNK PORTS TRUNK
IP IP NETWORK NET TRUNK_GROUP TKGP
These are the important commands normally used while configuring various objects.
This card list shows the names of the cards in the slots, their version and status. by this command we can see the list of cards in any shelf (0 to 15) and any slot (1 to 18). To see cards list of any slot in any shelf,
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 2
*: CLIS (CLIS)
Choose mode
0 - UPDATE
1 - DISPLAY
4 - SNAP
*: 1
FROM SHELF#- 0
TO SHELF#- 0
FROM SLOT# 1
TO SLOT# 5 CARDS LIST
shelf#/slot# p_type i_type card_db# vers/subver status
0 / 1 NO_CARD NO_CARD --- --- --- ÿÿ------
0 / 2 NO_CARD NO_CARD --- --- --- ÿÿ------
0 / 3 PUGW UGW --- 10 30 ACTIVE
0 / 4 30TM 30TM 0 52 51 ACTIVE
0 / 5 24SFT/00 24SDT --- 3 5 ACTIVE
To see ports list: this will provide the details of port list on a particular card such as subscriber card, trunk card or any service card. if you want to know the details of a port then choose physical location in the below command or if you wish to find out the port details of a defined number then choose dial number function in the below command. *: PLIS
(PLIS)
PORTS_LIST
0-PHYS_LOC
1-DIAL_NUM
*: 0 Choose mode
0 - UPDATE
1 - DISPLAY
*: 1
FROM SHELF#- 4
TO SHELF#- 4
FROM SLOT# 8
TO SLOT# 8 FROM CKT# 0
TO CKT# 240
PORTS LIST
SHELF/SLOT/CKT TYPE DIAL# PORT_DB# VERS SHORT & FULL NAMES
4 / 8 / 0 8T-C 7500 0 --- 8T_0 :BLANK
4 / 8 / 1 8T-C 7501 0 --- BLANK :BLANK
4 / 8 / 2 8T-C 7502 0 --- BLANK :BLANK
4 / 8 / 3 8T-C 7503 0 --- BLANK :BLANK
4 / 8 / 4 8T-C 7504 0 --- BLANK :BLANK
4 / 8 / 5 8T-C 7505 0 --- BLANK :BLANK
4 / 8 / 6 8T-C 7506 0 --- BLANK :BLANK
4 / 8 / 7 8T-C 7507 0 --- BLANK :BLANK
To see features available to a subscriber and Trunk *: FEAT
(FEAT)
0-CONTROL
1-AUTHORIZATIONS
*: 0 Choose mode
0 - UPDATE
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 3
1 - DISPLAY
*: 1
FROM DIAL# 400
TO DIAL# 400 CHOOSE FEATURE
1-ATTEND_MSG 14-BUSY_OUT 27-TIMED_FWD
2-CF_ALL 15-CO_BLOCKED 28-CLR_ID_RESTR
3-CF_BUSY 16-HOT_TK_DELAY 29-LAR_BLOCKED
4-DONT_DIST 17-DROP_NO_DIAL 30-CF_EXT_ALL
5-HOT_ST_IMM 18-HOT_TK_IMM 31-CF_EXT_BUSY
6-DIAL_LOCK 19-I/C_ONLY_TK 32-CF_NO_ANS_EXT
7-HOT_ST_DELAY 20-TK_RSRVD 33-TIMED_FWD_EXT
8-DIR_IN_LINE 21-NIGHT-1 34-AUTO_SET_RELOCATE
9-TERMIN_ONLY 22-NIGHT-2 35-FlexiCall_ALL
10-ORIGIN_ONLY 23-EXC_HOLD 36-FlexiCall_INT
11-ST_BLOCKING 24-PRIVACY 37-FlexiCall_EXT
12-O/G_TK_RESTR 25-O/G_ONLY_TK 38-IRSS
13-CF_NO_ANS 26-CHECK_OUT 39-CF_UNDEF
The above list is common to subscriber features, trunk features and system features. In update mode you can assign a suitable feature to the subscriber, trunk or system.
To see features authorized on the exchange *: FEAT
(FEAT)
0-CONTROL
1-AUTHORIZATIONS
*: 1
0- DISPLAY CURRENT
1- DISPLAY NEW (DISKETTE)
*: 0 1- PORTS - 955 24- SIP VOICE MAIL- 0 47- SL SAU CONTROL-(Na)
2- KEYSETS -XXXX 25- ROUTING -YES 48- HIGHEST VERSION -1599
3- SLTS-XXXX 26- DATA FEATURES -NO 49- E911-NO
4- TRUNKS-XXXX 27- SMDR BACKUP -YES 50- SPLIT MONITOR -NO
5- FlexSets-XXXX 28- 2nd LANGUAGE-YES 51- CVA -NO
6- KEYSETS_IP-10 29- 3rd LANGUAGE-YES 52- CVD -YES
7- T2xxM -22 30- 4th LANGUAGE-YES 53- CVD_PRO.-YES
8- FLIPS(SOFTPHONE)- 2 31- VFAC-NO 54- AUTO SET RELOCT.-NO
9- SENTINEL-XXXX 32- PRI -YES 55- FlexiCall -NO
10- SLT_IP-16 33- ACD -YES 56- SLT-CID -YES
11- LGS_IP- 0 34- HOTEL/MOTEL -YES 57- DIRECTORY -NO
12- NET_IP-16 35- CAP -YES 58- Freedom -NO
13- SIP TERMINAL-20 36- Traffic (CVT) -YES 59- FlexAIR SMS -NO
14- T2xxS -22 37- TBR -YES 60- SILENT MONITOR-YES
15- SIP TRUNK - 0 38- CoraLINK-NO 61- MLPP-NO
16- MEDIA_CHAN. -9999 39- NETWORKING-YES 62- MUSIC DIALTONE-NO
17- APA -XXXX 40- HSB -YES 63- CANNED MESSAGE-NO
18- DAYS-XXXX 41- FlexAIR SKK -YES 64- Not in use-NO
19- URC DTMF- 8 42- 4VS NO ANSWER -NO 65- CFM- NO
20- URC CLID- 0 43- CONF-YES 66- INTERNAL TRAFFIC-NO
21- URC 3WAY- 6 44- ST.-V.M.-YES 67- IPx Office-NO
22- URC CONF- 1 45- CALL TRACE-YES 68- Not in use-NO
23- URC MFR - 0 46- CALLER ID -YES
In the above list all the features which are been included in the exchange are displayed as some flexible numbers as ‘X’ some as numeric and some as ‘yes’ or ‘no’.
To see CoS of a subscriber and Trunk
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 4
*: SLT
(SLT)
Choose mode
0 - UPDATE
1 - DISPLAY
6 - DUPLICATE
*: 1
FROM DIAL#- 400
TO DIAL#- 400 SLT_DEF
DIAL# 400
prm_cos- 0 sec_cos- 0 priv_libs- 10 terminal- N
origin- N block- N o/g_tk_rest- N privacy- Y
excl_hold- N hard_hold- N last_num- Y security- N
dnd_wp Y rec_spk_status- N IP_fax- N IP_modem- N
att- N auto_unatt- N
auto_rel_al- N passcode- NONE check_out- N type- 1
announcer- N multi_app- N ans_with_hf- N receive_cid- Y
send_id- Y ali- NONE sec_ali- NONE opx- N
hf_relevant- Y call_trace- N #_of_calls_traced-0 perm/temp_r(p/t)-P
vip(Y/N) N v_mail- N vm_camp- N DTMF_signal- NONE
usic_on_hold- 0 ccr_tone N block_reorder-N failure report- N
keep_rtp N
The above list can be modified when needed including class of service. Various groups can be created. Each type of group has specific function to perform.
To see various groups *: GROUP
(GROUP)
0-HUNT
1-TK
2-BOSS
3-PICKUP
4-ZONE_PAGE
5-BELL/UNA
6-DID/E&M
7-GRP_CALL
8-ELA
*: 3 (PICK)
Choose mode
0 - UPDATE
1 - DISPLAY
*: 1
FROM PICKUP# 0
TO PICKUP# 0 0
------------
MEM# 1 85680
MEM# 2 85682
MEM# 3 85892
MEM# 4 85644
In the above group if a call arrives on one extensions then the other extension the group can pick up the call by dialling a pre-defined call pick-up code. This code is created in the exchange number plan.
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 5
This command will show you the total numbering plan or any specific category of numbering plan.this command is mostly used to add a dial number, delete a number and update a old dial number with new dial number without changing the port and its features.
To see numbering plan *: NPL (NPL)
NUM_PLAN
0-GENERAL
1-SPECIAL FEATURE CODES
2-FLEXICALL/IRSS FEATURE CODES
3-SHOW TYPE OF NUMBER
*: 0 GENERAL
Choose mode
0 - UPDATE
1 - DISPLAY 2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*: 1 FROM DIAL# TO DIAL# TYPE INDEX#/SHELF, SLOT, CKT/NODE#
7300 7329 TRUNK 4,3,1
120 122 SLT 0,13,0
408 408 KEYSET 0,5,10
401 406 SIP_TERMINA 0
981 989 TRUNK_GRP 0
To see details IP Gateway card *: IP (IP)
0-UGW
1-IP PORTS
2-TELEPHONY GW
3-GENERAL
4-STATISTICS
5-NET
6-ZONE
7-SIP DOMAINS
8-SENTINEL_PRO
*: 0 (UGWC)
0-DEFAULT
1-CURRENT
*: 1 Choose mode
0 - UPDATE
1 - DISPLAY
*: 1
FROM SHELF#- 0
TO SHELF#- 0
FROM SLOT# 3
TO SLOT# 3
0,3
------------
replace by (...) / add by (a,...) / remove by (r,...) / end by :
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 6
ZONE_LIST(0)
SIGNALING:
LOCAL_IP_ADDRESS (#/R) 010.051.028.200:2427
GLOBAL_IP_ADDRESS (#/R) 010.051.028.200:2427
SUBNET_MASK (#/R) 255.255.255.000
DEFAULT_ROUTER_ADDRESS (#/R) 010.051.028.254
QoS:
DiffServ (Y/N) - N
802.1Q/p (Y/N) - N
MEDIA:
MAC(#/R) 00:0A:6B:01:C9:F3
LOCAL_IP_ADDRESS (#/R) 010.051.028.201:16400
GLOBAL_IP_ADDRESS (#/R) 010.051.028.201:16400
SUBNET_MASK(#/R) 255.255.255.000
DEFAULT_ROUTER_ADDRESS (#/R) 010.051.028.254
PHYSICAL CAPACITY:
MEDIA_CHANNELS: MRC-16
RESOURCES_TYPES: - DTMF MFC
MAX_G711_MEDIA_CHANNELS 64
TOTAL END POINTS 240
END POINT TYPES - Keyset Slt Lgs Net SIP Media
REQUIRED CAPACITY:
MEDIA_CHANNELS 4
KEYSET 4
SLT 4
LGS 0
NET 4
SIP 4
To see the IP phones connected and their status. *: IP
(IP)
0-UGW
1-IP PORTS
2-TELEPHONY GW
3-GENERAL
4-STATISTICS
5-NET
6-ZONE
7-SIP DOMAINS
8-SENTINEL_PRO
*: 1 IP Ports
0-KEYSET
1-SLT
2-LGS
3-NET
4-SIP_TERMINAL
5-SIP_TRUNK
*: 0 (IPKEY)
0-INDEX_ACCESS
1-DIAL_NUMBER_ACCESS
*: 1 DIAL NUMBER ACCESS
Choose mode
0 - UPDATE
1 - DISPLAY
*: 1
FROM DIAL#- 401
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 7
TO DIAL#- 401 Keyset
401
------------
INDEX 0
CURRENT_ZONE0
REQUIRED_ZONE (#/R) 0
MAC (#/R) 00:1D:92:B7:3A:38
IP_ADDRESS
CONNECTED_VIA_SENTINEL N
EARLY_MEDIA_FOR_BANDWIDTH_CONTROL(Y/N) - N
STATUS:Active
QoS:
DiffServ(Y/N) - Y
802.1Q/p(Y/N) - Y
Security Type:
DES - N
Triple DES - N
AES - N
COMPRESSION_CAPABILITY -
PHONE_TIME_ZONE_OVERRIDE_BY_SYSTEM (Yes/No) - N
(*Value in 15 min increments. Range: 0 to +/- 12)
DELTA_TIME_FROM_GMT (+/- HH:MM / R) - 0:00
In above command we are looking at the details of extension 401 which is defined in the exchange as an IP keyset account. After the account gets registered on any phone device, the details of phone such as name of the device, IP address and status are also shown. Use of npl command to add, delete and modify any dial numbers such as subscriber dial numbers, trunk dial numbers, feature codes, and virtual numbers. To modify any dial number *: NPL
(NPL) NUM_PLAN
0-GENERAL
1-SPECIAL FEATURE CODES
2-FLEXICALL/IRSS FEATURE CODES
3-SHOW TYPE OF NUMBER
*: 0
0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
Choose mode
*: 0 FROM OLD DIAL# - 408
TO OLD DIAL# -
FROM NEW DIAL# - 407
UPDATE (Y/N)? Y
NUMBERS UPDATED
To remove any dial number *: 3
FROM OLD DIAL# - 408 TO OLD DIAL# -
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 8
NUMBERS REMOVED
To add any dial number 0 - UPDATE
1 - DISPLAY
2 - ADD
3 - REMOVE
5 - SHOW
7 - ERASE
*: 2
FROM NEW DIAL# - 408 TO NEW DIAL# -
NUMBERS ALREADY DEF? (Y/N) N 0 - TRUNK 1 - SLT
2 - KEYSET 3 - KEYSET_V_PAGE
4 - TRUNK_GRP 5 - HUNT_GRP
6 - BOSS_GRP 7 - PUBLIC_LIB
9 - FEATURE 10 - EDIT
11 - BELL 12 - PAGE
13 - MODEM 14 - DID_NUMS
16 - DATA_PORT 19 - PRIVATE_LIB
20 - KEYSET_Z_PAGE 21 - RELAY
22 - DATA_USER 23 - DATA_GRP
30 - CONF 31 - DVMS_MSG
32 - DVMS_PORTS 33 - PAGE_Q
35 - GROUP_CALL 36 - DIAL_SERV
37 - ROUTING_ACC 38 - WAIT_QUE
39 - NETWORK 40 - WIRELESS
41 - IP_KEYSET 42 - IP_SLT
43 - IP_LGS 44 - IP_KEY_VPG
45 - IP_NET 46 - SIP_TERMINAL
47 - SIP_TRUNK 48 - DYNAMIC_CONF
Choose type
*: 1 ENTER (SHELF, SLOT, CKT) - (4, 6, 0)
NUMBERS ADDED
Review Questions
1. Write the commands for the following tasks?
S. No. Command Task
1 See the port of the telephone No. 400
2 See the telephone No. in location (0,13,8)
3 Change the phone No. 408 to 409
4 See the CoS for phone No. 400
5 See the groups and write their names
6 See the telephones in pickup group ‘0’
7 See the nodes number plan
IRIS
ET
-
Telephony Lab --------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------
04/05/2020 9
8 See the card in slot 5 of shelf 0
9 See the port in slot 12 of shelf 0
10 To update the old number with a new number
Notes
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Signature of the Trainee
IRIS
ET