Ipd Volvo V70, S60 Aluminum Skid Plate Pi 286 Skid Plate Installation Instructions

2
11744 NE Ainsworth Circle, Portland, OR 97220 • (503) 257-7500 • Fax (503) 257-7596 Installation Instructions Dedicated to improving vehicle fun, safety & performance Skid Plate for S80, S60, V70, XC90 5 & 6 cyl ipd #5360 SUGGESTED TOOLS • Sockets • Wrenches • Hoist, ramps or jack stands INSTALLATION Elevate the front of the car to make working under the engine easier. Remove the plastic engine cover if so equipped. Measure length of rubber seal strip and cut pieces to fit for both left and right side. Remove the paper to expose the tape and stick to skid plate. Hold the skid plate up to the bottom of the engine compartment. Install the center front mounting 8mm x 25mm bolt first finger tight. Install the front 8mm x 25mm bolt closest to the oil filter. A. Install the drivers side 8mm x 40mm bolt using the plastic spacer between the skid plate and the frame finger tight. B. For XC90, use the forward mounting hole with both white plastic spacers and the 60mm bolt. For all others use the short spacer and short bolt, discard the long spacer and long bolt. PI-286 • 6/04 1 2 3 4 5 6 7 XC90 7A 7B 3

Transcript of Ipd Volvo V70, S60 Aluminum Skid Plate Pi 286 Skid Plate Installation Instructions

Page 1: Ipd Volvo V70, S60 Aluminum Skid Plate Pi 286 Skid Plate Installation Instructions

11744 NE Ainsworth Circle, Portland, OR 97220 • (503) 257-7500 • Fax (503) 257-7596

Installation Instructions Dedicated to improving vehicle fun, safety & performance

Skid Plate for S80, S60,V70, XC90 5 & 6 cyl

ipd #5360

SUGGESTED TOOLS• Sockets • Wrenches • Hoist, ramps or jack stands

INSTALLATIONElevate the front of the car to make working under the engine easier.

Remove the plastic engine cover if so equipped.

Measure length of rubber seal strip and cut pieces to fit for both leftand right side. Remove the paper to expose the tape and stick toskid plate.

Hold the skid plate up to the bottom of the engine compartment.

Install the center front mounting 8mm x 25mm bolt first finger tight.

Install the front 8mm x 25mm bolt closestto the oil filter.

A. Install the drivers side 8mm x 40mmbolt using the plastic spacer between theskid plate and the frame finger tight.

B. For XC90, use the forward mountinghole with both white plastic spacers andthe 60mm bolt. For all others use theshort spacer and short bolt, discard thelong spacer and long bolt.

PI-286 • 6/04

1

2

3

4

5

6

7

XC90

7A 7B

3

jbeale
Callout
13mm socket
jbeale
Callout
The rubber seal was already installed on mine
jbeale
Callout
I found it easier to do the center bolt second; I did the bolt by the oil filter first.
jbeale
Callout
This didn't work for me. I ended up using the long spacer and the shorter bolt of the two long bolts, and I used the long spacer after cutting the long spacer down to 1" long.
jbeale
Callout
For both cars (my V70 and S60, I had to enlarge this hole sideways using a Dremel with a die grinder bit. Relative to the picture shown here, I enlarged the left-hand portion of the right hand hole; the bolt would not align with the threaded hole otherwise.
Page 2: Ipd Volvo V70, S60 Aluminum Skid Plate Pi 286 Skid Plate Installation Instructions

Using the supplied cup washers, 10mm x 25mm bolts and 10mmnuts mount the rear of the skid plate to the frame. The cup washerswill be flat against the inside of the frame and against the skidplate.

Tighten all bolts. The rear boltswill require a wrench to holdthe nuts inside the frame.

WARRANTY INFORMATION

9

INSTALLATION8

8

2 • Skid Plate ©2003 ipd PI-286

One Year Limited Warranty

ipd warrants to the original purchaser that the parts manufactured and/or sold by ipd (the Product) is free from defects in material andworkmanship under normal use. ipd warrants that the Product will perform substantially in accordance with the specifications set forth in thedocumentation provided with it. The above express warranties are made for a period of the lesser of 12,000 miles or 12 months from the datethe Product is installed in your vehicle.

Any improper use, operation beyond capacity, substitution of parts not approved by ipd in writing, any alteration or repair by others, or anyremoval, defacing or altering of the identification shall void this warranty. There is no warranty on high-performance or race related partsdue to the nature of usage.

The purchaser shall notify ipd at 1-800-444-6473 of any defect within the warranty period no later than thirty (30) days after purchaserdiscovers the defect. Should any failure to conform to this warranty appear within the warranty period, ipd shall, on notification, correct thenonconformity at its option, either by repairing any defective part, or by making available, FOB ipd’s plant, a repaired or replacement part.The purchaser must insure any defective item being returned because ipd does not assume risk of loss or damage while in transit. Nopayment or reimbursement shall be made for installation, removal, transportation or other charges. The remedies set forth in this instrumentare exclusive, and the liability of ipd with respect to any sale shall not exceed the price of the product on which the liability is based.

EXCEPT AS STATED OTHERWISE IN THIS WARRANTY, ipd MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANYWARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some states do not allow limitations on how long an impliedwarranty lasts, so the above limitation may not apply to you. ipd shall not in any case be liable for special, incidental, consequential,indirect, or other similar damages arising from any breach of these warranties even if ipd or its agent has been advised of the possibility ofsuch damages. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation orexclusion may not apply to you.

This warranty is governed by the laws of the State of Oregon.

8

jbeale
Callout
The curved edges of the washer face away from the surface
jbeale
Callout
16mm (or 5/8") open end wrench for bolt head; 17mm socket for nut