IP Dome Camera Hardware Guide - CCTV Center Dome PTZ Camera_manual_eng.pdfIP Dome Camera Hardware...

IP Dome Camera

Hardware Guide

IP dome.book Thursday, August 23, 2007 10:05 AM

THIS MANUAL WAS CREATED ON AUGUST 23, 2007.

LEGAL CONSIDERATIONS LAWS THAT CAN VARY FROM COUNTRY TO COUNTRY MAY PROHIBIT CAMERA SURVEILLANCE. PLEASE ENSURE THAT THE RELEVANT LAWS ARE FULLY UNDERSTOOD FOR THE PARTICULAR COUNTRY OR REGION IN WHICH YOU WILL BE OPERATING THIS EQUIPMENT. INDIGOVISION LTD. ACCEPTS NO LIABILITY FOR IMPROPER OR ILLEGAL USE OF THIS PRODUCT.

COPYRIGHT COPYRIGHT © 2007 INDIGOVISION LIMITED. ALL RIGHTS RESERVED.

THIS MANUAL IS PROTECTED BY NATIONAL AND INTERNATIONAL COPYRIGHT AND OTHER LAWS. UNAUTHORIZED STORAGE, REPRODUCTION, TRANSMISSION AND/OR DISTRIBUTION OF THIS MANUAL, OR ANY PART OF IT, MAY RESULT IN CIVIL AND/OR CRIMINAL PROCEEDINGS.

INDIGOVISION AND VIDEOBRIDGE ARE TRADEMARKS OF INDIGOVISION LIMITED AND ARE REGISTERED IN CERTAIN COUNTRIES. ALL OTHER PRODUCT NAMES REFERRED TO IN THIS MANUAL ARE TRADEMARKS OF THEIR RESPECTIVE OWNERS.

SAVE AS OTHERWISE AGREED WITH INDIGOVISION LIMITED AND/OR INDIGOVISION, INC., THIS MANUAL IS PROVIDED WITHOUT EXPRESS REPRESENTATION AND/OR WARRANTY OF ANY KIND. TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAWS, INDIGOVISION LIMITED AND INDIGOVISION, INC. DISCLAIM ALL IMPLIED REPRESENTATIONS, WARRANTIES, CONDITIONS AND/OR OBLIGATIONS OF EVERY KIND IN RESPECT OF THIS MANUAL. ACCORDINGLY, SAVE AS OTHERWISE AGREED WITH INDIGOVISION LIMITED AND/OR INDIGOVISION, INC., THIS MANUAL IS PROVIDED ON AN “AS IS”, “WITH ALL FAULTS” AND “AS AVAILABLE” BASIS. PLEASE CONTACT INDIGOVISION LIMITED (EITHER BY POST OR BY E-MAIL AT [email protected]) WITH ANY SUGGESTED CORRECTIONS AND/OR IMPROVEMENTS TO THIS MANUAL.

SAVE AS OTHERWISE AGREED WITH INDIGOVISION LIMITED AND/OR INDIGOVISION, INC., THE LIABILITY OF INDIGOVISION LIMITED AND INDIGOVISION, INC. FOR ANY LOSS (OTHER THAN DEATH OR PERSONAL INJURY) ARISING AS A RESULT OF ANY NEGLIGENT ACT OR OMISSION BY INDIGOVISION LIMITED AND/OR INDIGOVISION, INC. IN CONNECTION WITH THIS MANUAL AND/OR AS A RESULT OF ANY USE OF OR RELIANCE ON THIS MANUAL IS EXCLUDED TO THE FULLEST EXTENT PERMITTED BY APPLICABLE LAWS.


3

TABLE OF CONTENTS

ABOUT THIS GUIDE.......................................... 5Safety Notices ...............................................................5

1 CABLING .................................................... 7Cable & Wiring Requirements .......................................7

2 INITIAL IP DOME CONFIGURATION.................. 9Initial IP Properties ........................................................9Using the Web Configuration Pages .............................9

Step 1 — Preparing an Isolated Network ....................10Step 2 — Preparing for Initial Device Configuration....10Step 3 — Configuring your IP Dome ...........................12

Using the Serial Port Connection ..................................15Attaching the IP Dome to the Network ..........................17

3 DOME INITIALIZATION .................................... 19Camera Sensor Verification ..........................................19Click-On Lanyard Fixing ................................................20

4 MOUNTING THE INTERNAL DOME ................... 23Installing the Internal IP Dome Ceiling & Wall Mount ....23Installing the Internal Corner Mount (optional) ..............24Installing the Internal IP Dome False Ceiling Mount .....25Making Connections & Completing Installation .............26

Step 1 - Making Connections ......................................26Step 2 – Fitting the IP Dome Body ..............................27Step 3 – Fitting the Locking Screw..............................28Step 4 – Attaching the Acrylic .....................................28Step 5 – Powering up ..................................................28

5 MOUNTING THE EXTERNAL DOME .................. 29Installting the External IP Dome Wall Mount ................29


4

Assembling the External IP Dome Wall Mount ............. 30Installing the External IP Dome Soffit Mount (optional) 31Installing the External Pole Mount (optional) ................ 32Installing the External Corner Mount (optional) ............ 33Installing the External Swan-neck (optional) ................ 34Making Connections to External Domes and Completing Installation ............................................... 35

APPENDIX A – REMOTELY RESETTING THE DOME ............................................................. 37

APPENDIX B – HARDWARE SPECIFICATION....... 39Codec Specification ...................................................... 39

Video .......................................................................... 39Console Input/Output.................................................. 39Network Connections ................................................. 40IndigoVision IP Dome Camera Metrics....................... 40Environment ............................................................... 40Regulatory .................................................................. 41

Camera Dimensions ..................................................... 41Internal Dome Camera ............................................... 41

Sensor Specification ..................................................... 43

INDEX ..........................................................45


5

ABOUT THIS GUIDE

This guide is written for users of IndigoVision’s IP Dome Camera. It provides introductory information about the product, and a description of the hardware and specifications.

For information on how to use the Web Configuration pages to configure the unit, see the IndigoVision 8000 Web Configuration Guide.

Safety NoticesThis guide uses the following formats for safety notices:

Note: Additional information relating to the current section.

Caution: Potential hazard that could seriously impair operation.


6


7

1 CABLING

The following information applies to both internal and external IndigoVision IP Dome Cameras, unless otherwise specified.

Cable & Wiring RequirementsTable 1 details the cabling and wiring requirements for the IP Dome.

Caution: To ensure optimum IP Dome performance, you must adhere to these parameters. Failure to do so will invalidate the warranty.

Table 1 Distances per cable size (in meters)

Cable size

Internal IP Domes, (without heater) Max. Distances

External IP Domes, (with heater) Max. Distances

Power 0.75 mm2 75m 30m

1.00 mm2 100m 40m

1.25 mm2 125m 50m

1.50 mm2 150m 60m

2.50 mm2 250m 100m


8


9

2 INITIAL IP DOME CONFIGURATION

Caution: You must configure your dome’s IP settings before you mount the dome in its final position.

You can configure your IP Dome using the Web Configuration pages, or a serial connection. The Web Configuration method is detailed below. If you are using a serial port, see “Using the Serial Port Connection” on page 15.

Initial IP PropertiesBy default, these devices are programmed with the IP properties shown in Table 2.

Using the Web Configuration PagesTo configure your IP Dome using the Web Configuration pages you must:

1 Prepare an isolated network.

2 Prepare your PC for initial device configuration.

3 Configure your IP Dome. This includes specifying its IP address and subnet mask.

Table 2 Default IP Properties

Initial ConfigurationIP Address 10.5.1.10

Subnet Mask 255.0.0.0

Default Gateway 10.0.0.1


10

You must also have one of the following:

• A CAT5 crossover cable suitable for connection between the PC and the RJ45 connector on the IP Dome, OR

• An isolated hub or a switch with a standard CAT5 cable

Step 1 — Preparing an Isolated NetworkYou should connect your IP Dome and the PC you are using to configure it on their own isolated network. To do this, connect the unit to the PC using an Ethernet cross-over cable (see Figure 1.)

Figure 1 Connecting the unit and PC using a cross-over cable

Alternatively, you can connect the unit and PC to the same isolated hub or switch (Figure 2):

Figure 2 Connecting the unit using an isolated hub/switch

Step 2 — Preparing for Initial Device ConfigurationAll devices are supplied with their IP address and subnet mask set to 10.5.1.10 and 255.0.0.0 respectively. You cannot connect the devices to your network until you have changed these settings to suit your network.

To change the factory defaults of your IP Dome, you must first (temporarily) modify your PC’s network settings.

Power Supply

Cat5 crossovercable

PC

PCIsolated hub

or switch

Power SupplyCat5 crossovercable


11

Caution: Please note the original value of all settings that are to be changed so that you can re-enter them when you have completed the initial device configuration.

To change your PC’s settings:

1 Use the Windows XP Network Settings configuration application to set the PC’s IP address and subnet mask, as follows:

a. In Windows Explorer, right-click Network Neighborhood and select Properties.

b. Right-click Local Area Network and select Properties.

Figure 3 LAN Properties

c. Right-click Internet Protocol (TCP/IP) and select Properties.


12

Figure 4 IP Properties

d. Set the IP address to an address close to the factory IP address, for example, 10.5.1.2 and change the PC’s subnet mask to 255.0.0.0 (the same as the factory default).

e. Click OK, then OK again.

Step 3 — Configuring your IP DomeOnce you have changed your PC’s network settings, you must change the IP values of your IP Dome from its factory defaults.

All devices are supplied with their IP address and subnet mask set to 10.5.1.10 and 255.0.0.0 respectively. You cannot connect the devices to your network until you have changed these settings to suit your network.

To change these values:

1 Open Windows XP’s Internet Explorer application. From the File menu, select Open, and enter 10.5.1.10 (the factory default IP address), then click OK.


13

2 The Web Configuration home page appears (Figure 5):

Figure 5 Web Configuration home web page

3 Click the Network link on the left of the web page:

Figure 6 Network web page

4 The fields are as follows:

• Host Name — Enter a name for the IP Dome to identify the device.

• Location — Enter a location to identify the device.


14

• IP Address — Enter the IP address of the device.

• Subnet Mask — Enter the IP network subnet mask.

Caution: Ensure that you enter the correct values. Once you change from the defaults, the device is no longer configurable by the PC with its current network settings.

• Default Gateway — This is the appropriate default gateway for remote network access and is only required if the devices are to be accessed from a different subnet.

• Ethernet Interface — Enter a link type. The values are as follows:

• 0 - 10Mbps Half-Duplex

• 1 - 10Mbps Full-Duplex

• 2 - 100Mbps Half-Duplex

• 3 - 100Mbps Full-Duplex

• 4 - Auto-negotiate

You may need to change the Ethernet link type default value from Auto-negotiate for some network devices. If you have problems maintaining a network link, contact your system administrator to determine the appropriate setting.

When you have configured the device as required, click Submit to apply the changes to the device.

5 To configure another device, disconnect the cable from the device. Leave the cable connected to the PC.

Note: You may want to make a note of the device’s new IP address and subnet mask, or label the device with its new details.

6 Connect the crossover cable to the next device you want to configure.

7 Type the following command from a Command Window:

C:> arp -d 10.5.1.10

Note: You must do this before you can access the next unit for configuration.


15

8 Repeat these steps for each device, using different IP addresses for each device.

Caution: Ensure that no two devices share the same IP address (or that of the PC).

9 When you have configured all your devices, return the PC to its original settings, or change them as appropriate for your network.

10 You are now ready to take your device(s) off the isolated network and connect them to the main network. See “Attaching the IP Dome to the Network” on page 17.

Using the Serial Port ConnectionTo configure your IP Dome using the serial port, you require a standard RS232 serial cable and the serial cable shipped with the IP Dome.

1 Power up the dome, and wait for its initialization process to complete (about one minute) (see Chapter 3).

2 Connect the serial cables between the unit and the PC as shown in Figure 7.

Figure 7 Serial port connection

configuration softwarePC with serial

Attach the 3-pin connector end of the serial cable to CON8 on camera board

Standard serial cable Serial cable shipped with IP Dome

9 pin DSUBfemale matesto PC

3 pin connectormates to board

Serial cable

IP Dome with baseremoved

000-0119-02

CON8

CON6


16

3 On the PC, use a Terminal Emulation program such as Windows HyperTerminal and set the serial port parameters as follows:

• 115200 baud

• 8 bits

• No parity

• 1 stop bit

• Flow Control: None

4 Connect to the unit and press Enter. You should see the following prompt:VB8000 Vp-xxx Version vX-X-X

Device Type: Transmitter

Location: Unknown

Network Settings [10.5.1.10/255.0.0.0/10.0.0.1]

VB8000 login:

5 Log in to the unit using the username "config" and password "config". The unit prompts you to enter the new configuration values. At each prompt, press <Enter> to accept the current value.

• IP Address — Enter the IP address of the unit.

• Subnet Mask — Enter the IP network subnet mask.

• Default Gateway — Enter the appropriate default gateway for remote network access: this is only required if the devices are to be accessed from a different subnet.

• Link type — Enter a link type. The values are as follows:

• 0 - 10Mbps Half-Duplex• 1 - 10Mbps Full-Duplex• 2 - 100Mbps Half-Duplex• 3 - 100Mbps Full-Duplex• 4 - Auto-negotiate

You may need to change the Ethernet link type default value from Auto-negotiate for some network devices. If you have problems maintaining a network link, contact your system administrator to determine the appropriate setting.

• Host name — Enter a name to describe the unit.


17

• Location — Enter a name to describe the location of the unit.

• Reset Network Security to factory defaults (y/n) ? — Enter "y" to reset the unit's password and network security settings. This will enable unrestricted access to the configuration web pages, and is the only way to reset the password on the unit. Enter “n” if you do not want to make changes to the unit's network security.

If you have more than one device, repeat these steps for each device.

You are now ready to attach the device(s) to the network.

Attaching the IP Dome to the NetworkAfter configuring the dome’s IP settings, you must attach it directly to your network using an available network port, as follows:

1 Reconnect your PC to the network.

2 Use a standard RJ45 connector and CAT5 cable to connect to the network socket in the dome, as shown in Figure 8.

Figure 8 Connecting an IP Dome to the network

Power Supply

PC

Network


18


19

3 DOME INITIALIZATION

Each time the IP Dome is powered up, it performs an initialization process, during which the camera sensor moves to the home position. This should take about a minute. You must wait for this process to complete before attaching serial or video cables to the connectors inside the dome enclosure.

Camera Sensor VerificationOnce the camera has completed its initialization process, you can use the BNC connector on the IP Dome board to check that the camera sensor is working properly. The BNC connector is shown in Figure 9.

Figure 9 BNC Connector

Note: Please ensure that you disconnect any cables from the BNC connector after testing.

BNC connector can be used during installationto verify correct operation of the sensor

CON1

IC6

CON7

D2

OPT

1


20

Click-On Lanyard FixingThe lanyard is supplied fastened inside the IP Dome external top cover. To fasten it to the ‘dome-inner’, pull the keyhole end downwards and attach it as shown below:

Lanyard

Keyhole end

Stem

Button

Place keyhole over button

Pull lanyard so thatthe slotted hole clicksinto place on the stem


21

In use, the keyholewill rotate around thebutton but will remainsecure


22


23

4 MOUNTING THE INTERNAL DOME

Caution: Before mounting the IP Dome in its final position, you must first configure its IP settings, as detailed in Chapter 2.

Installing the Internal IP Dome Ceiling & Wall Mount

Caution: Always handle the IP Dome carefully so that the main electronics and motor mechanism are not damaged.

1 Attach the appropriate bracketry to a firm, solid surface (ceiling or wall) using the required fixings. Ensure that you take the camera size and weight into consideration (see Appendix A for details).

53mm 46mm

Use three screws to affix dome base to ceiling.

Use central hole in dome base for top entry of cables

Locking screw usesthis slot for orientation

Use the "knockout" section of the domebase for side entryof cables

Affix lanyard securelyto ceiling.


24

Figure 10 Attaching bracketry

2 Feed the cables along the bracket, then attach the supplied clip-on lanyard to secure the unit.

You are now ready to make connections and complete installation. See “Making Connections & Completing Installation” on page 26.

Installing the Internal Corner Mount (optional)The Internal Corner Mount Adapter is an optional extra accessory part.

For internal corner mounts, fasten the adapter to the corner of the walls using suitable fixings, then follow the instructions in “Installing the Internal IP Dome Ceiling & Wall Mount” on page 23. An internal corner mount adapter is shown below.

Figure 11 Internal corner mount adapter

Orient dome to line up locking tab with slot in dome body. Twist body onto bracket.Important - fit locking screw

The two parts of the wall bracket are securedby fitting this screw

246mm 161mm 55mm

Locking tab


25

Figure 12 Internal corner mount adapter dimensions

Installing the Internal IP Dome False Ceiling Mount

For camera weight and dimensions, see Appendix A.


Figure 13 Dimensions and bracketry required to install the IP Dome

8mm55mm

75mm

145mm

101m

m

45mm

41mm

26mm

51mm

Twist off top partto gain access toconnections

Fit acrylic by twisting clockwise.Remove acrylic bytwisting anti-clockwise


26

Cut a hole in the false ceiling tile (see Figure 14). Ensure that you take the weight of the IP Dome and support plate into consideration. Attach the supplied lanyard to secure the unit.

Figure 14 Fixing to a false ceiling tile

You are now ready to make connections and complete installation. See “Making Connections & Completing Installation”.

Making Connections & Completing Installation

Step 1 - Making ConnectionsThe internal dome connection board is located at the top of the dome and is visible when the dome is removed from the internal wall bracket or internal ceiling mount.

Use cable tie to securecables to the horizontal barat the top of the top piece

Lanyard is screwedto the hole in top ofdome. Screw free endto part of the structureof the building

The support plate canbe fitted above theceiling tile or inplace of a 300mm x 600mm ceiling tile

Clamp swings out to support dome as the screw is tightened (clockwise)

When screw is loosened (anti-clockwise) the clamp swings inward to allow the cylindrical dome body to pass through the hole in the ceiling

The holes in the support plate can be securedto the buildingstructure using2mm dia binding wire

Twist off top part togain access to connections


27

Figure 15 IP Dome (Internal) Connection Board

Connect the power cable to CON1 and the network cable to CON3.

Note: Due to space restrictions, it may be necessary to use a network cable without a shround on the RJ45 plug at the dome camera end.

Step 2 – Fitting the IP Dome BodyAlign the screw mount to the screw socket on either the wall or ceiling mount bracket – there is only one way to align and fix the top section. Once aligned, push up and twist clockwise to ensure the three fixing lugs are located correctly (Figure 16).

Figure 16 Fitting internal dome body

Clip lanyard onto dome body

Dome base orwall bracket

Twist body of IP Dome onto domebase or wall bracket.Secure using lockingscrew

Dome body

Twist acrylic ontodome body

Locking screw


28

Step 3 – Fitting the Locking ScrewOnce twisted and locked, insert 1 x M3 CSK screw (provided in fixing pack) and tighten securely. This ensures that the installation is rigid and secure.

Step 4 – Attaching the AcrylicTo attach the acrylic, line up the three gaps in the rim of the acrylic with the three lugs on the IP Dome. Push and twist clockwise for a clean and easy fit.

Step 5 – Powering upAfter ensuring all fixings are secure, connect the mains power input to the PSU to power up the IP Dome.


29

5 MOUNTING THE EXTERNAL DOME

Caution: Before mounting the IP Dome in its final position, you must first configure its IP settings, as detailed in Chapter 2.

Installting the External IP Dome Wall Mount The external IP Dome camera has an IP65 rating. For camera weight and dimensions, see Appendix A.



30

Assembling the External IP Dome Wall Mount

Figure 17 Enlarged View of External IP Dome Wall Mount

Attach the wall bracketry using the required fixings.

Note: Ensure that you take the weight and stability of the surface to which the bracket is to be fixed into consideration.

You are now ready to make connections and complete installation. See page 35.

wall mount

top cover

lanyard

cameraassembly

captive screws

inner cover

captive screwfor fixing innercover

lanyard

captive screws for fixing external acrylic

external acrylic


31

Installing the External IP Dome Soffit Mount (optional)

The soffit adaptor is an optional extra accessory part. For camera weight and dimensions, see Appendix A.


For soffit installations, please use the soffit adaptor and gasket.

1 Fasten the soffit adaptor to the ceiling or soffit.

2 Fasten the external cover to the soffit using three screws.

Figure 18 Mounting Soffit Adaptor for Soffit & Pole Mounted External Domes


3 holes on 68mm PCDUse these holes forfastening soffitadaptor to ceiling

Gasket

Affix top coverhere using 3 screws


32

Installing the External Pole Mount (optional)The External Pole Mount Adaptor is an optional extra accessory part. For camera weight and dimensions, see Appendix A.

For pole mount installations, you must use an external wall mount housing with a pole mount adapter. The pole mount adapter is shown in Figure 19.

Figure 19 Pole mount adaptor

1 Fix the pole mount adapter to the pole using suitable fixings.

2 Fix the bracket to the pole adapter using suitable fixings.

3 Draw the cabling through the adapter into the bracket’s fixing box. Withdraw the cable sealing plug from the neck of the housing at the fixing box end. Make a small cut in the sealing plug for each cable that will be drawn through the bracket, thread the cabling through the bracket and push the plug back into place at the base of the housing neck.

4 Refit the cover to the bracket fixing box.


Side View

Underside View

4 fixing holeson 102 PCD

140mm

102mm

102mm

112mm


33

Installing the External Corner Mount (optional)The External Corner Mount Adapter is an optional extra accessory part.

For external corner mounts, fasten the adapter to the corner of the walls using suitable fixings.

The external corner mount adapter is shown in Figure 20.

Figure 20 External corner mount adapter dimensions

248.4

35.9 DIA

20

40.0

130.

0

100.0both sides

107.0

90.0

100.0

173.

5

4 holes on each side for fastening bracket to wall. 100 (h) x 70 (w)

100.

0bo

th s

ides

°


34

Installing the External Swan-neck (optional)For camera weight and dimensions, see Appendix A.

When the external swan-neck is purchased with an external IP Dome, the IP Dome top cover is already fitted to the swan-neck. If they are ordered separately then the swan-neck must be fastened to the top cover during installation. You must include the two gaskets. The swan-neck is fastened to the top cover using three screws fitted from inside the top cover (see Figure 21).

Figure 21 Swan-neck installation

1 Fit the external top cover to the swan-neck.

2 Thread the cables through the swan-neck.

3 Fit the swan-neck to the top of pole or parapet using suitable fixings.

You are now ready to make connections and complete installation.

Swan-neck

External top cover(part of externaldome camera)

568mm

295mm

200mm

Four holes dia7mm on 102mm(4") PCD


35

Making Connections to External Domes and Completing Installation

The external dome heater connection board is located inside the top housing of the external dome, and is visible when the dome ‘inner’ is removed.

Figure 22 External dome connection board

1 Remove the dome 'inner' and make the following connections

• Heater Power

Connect Output 2 from the PSU board to CON1 on the power connection board (000-0110-003) located at the top of the external housing.

• Network Connections

Connect the network cable to the RJ-45 (CON3) on the PCB at the top of the dome camera (000-0125-01) (see Figure 22).

• Camera Power

Connect Output 1 from the PSU board to CON1 on the PCB at the top of the dome camera (000-0125-01) (see Figure 22).

• Lanyard

Attach the lanyard from the dome 'inner' assembly to the housing top cover.

Heater connector CON2 (alreadyconnected)

Not used

Not used

Power Connections

Connect 24Vac to24VAC terminalsCON1


36

2 Locate the dome inner into the housing, ensuring that the guide slots for the fixing screws slide over the posts in the housing upper. Tighten the four Pozi pan fixing screws to secure the dome inner to the housing.

3 After ensuring all fixings are secure, connect the mains power input to the PSU to power up the IP Dome.


37

A REMOTELY RESETTING THE DOME

You can remotely reset an IP Dome using IndigoVision’s CCTV Keyboard.

1 Press and hold .

2 Press ‘5’,’8’,’5’,’8’.

3 Press ..

The IP Dome will then power down, re-power up and perform an initialization routine. Settings such as presets and guard tours are retained on the IP Dome.

Note: This only resets the camera and dome mechanics. To reset the codec, click Reboot on the Diagnostics web page.


38


39

B HARDWARE SPECIFICATION

This chapter details the hardware specifications for the IndigoVision IP Dome Camera. It provides the codec and sensor specification and the dimensions for each camera type.

Codec Specification

Video• 1Vp-p, 75ohm (PAL or NTSC depending on model)

Note: Video output is for debug/installation purposes only.

Video Codec• ISO/IEC Standard MPEG-4 Simple Profile

• User-configurable bit rate

• User-configurable frame rate

• “4:2:0” YUV color space

Resolution• SIF

• 2SIF

• 4SIF

Console Input/Output

Console• EIA-574 RS232 only

• Maximum Baud Rate 115.2 Kbps

• Console Settings 115200, 8bits,1 Stop Bit, No Parity


40

Network Connections• IEEE 802.3 and IETF standards:

• 10/100 Base-T Ethernet, TCP, UDP, ICMP and IGMP

• Physical connection via RJ-45

IndigoVision IP Dome Camera Metrics

DimensionsSee page 41.

WeightThe following unit weights include PSU, Acrylic and Codec. They do not include packaging:

• Internal Wall Mount Dome: 2.15 Kg

• Internal Pendant Mount Dome: 1.98 Kg

• Internal False Ceiling Mount Dome: 2.15 Kg

• External Wall Mount Dome Kit: 4.50 Kg

• External Swan Neck Dome Kit: 4.45 Kg

Power• Current consumption for internal or external IPDomes,

including CODEC but not including heater:

• Dome supply 24vac or 24vdc. Typical 500mA. Maximum 600mA

• Current consumption for heater (fitted to External IP Domes):

• Inrush current: Typical 1A, Maximum 2A (using 24vac or 24vdc).

• Normal operation: Less than 0.4A

Environment• Operating temperature:

• Internal Dome: 0°C (32°F) to + 50°C (122°F)• External Dome: -20°C (-4°F) to + 50°C (122°F)

• Storage temperature -20°C (-4°F) to + 70°C (158°F)

• External dome housing is IP65 rated


41

Regulatory• EN 55022(1994) ITE emission standard – Class A

• EN 61000-3-2(1995) mains harmonics – Class A

• EN 55024(1998) ITE immunity standard

• EN 61000-3-3(1995) voltage fluctuation

• CFR47(1995) Part 15 subpart B – Class A (US federal code of regulations)

Camera Dimensions

Internal Dome Camera

In accordance with the EC Waste Electrical and Electronic Equipment (WEEE) directive 2002/96/EC this product must be sent to a recycling plant for proper disposal at the end of its use.

204mm

73mm

51mm

171mm

197mm

214mm

116mm

99mm

Hole diameter 205mm

Space for cables above 10mm

250mm


42

External Dome Cameras

85mm

130mm

102mm

29mm

155mm

278mm

261mm

171mm260mm

200mm

568mm

295mm


43

Sensor SpecificationCamera Features All domes have the following functionsColor (C) Col / mono (C/M) C/M (indoor color only)

Sensor 1/4” ExView HAD

Zoom - optical + digital 18x, 12x

Zoom - total 216x

Line resolution 460

Pixels 752(H) x 582(V)

Horizontal view angle 2.8°(T) 48° (W)

Lens size 4.1 - 73.8 mm

ExView technology Y

Min sensitivity - color 0.7 Lux

Min sensitivity - color int 0.05 Lux (outdoor only)

Min sensitivity - mono int 0.01 Lux (outdoor only)

Signal/noise ratio >50 dB

Picture freeze Y

Video output 1 V p to p, 75ohms

Focus / iris Auto / manual

Presets 360

Tours 4 (max 128 presets per tour)

Learned patrols 4 mimic tours - up to 30 minutes duration each

Remote reset Via OSD, IP network

Dynamic privacy zones Up to 32 with 8 present on screen simultaneously

Preset status information Y

Variable pan speed/coverage 0.1 - 400°/sec, 360° continuous rotation, absolute positioning

Variable tilt speed 0.1 - 200°/sec, absolute positioning

Tilt coverage 90°

Auto homing Goes to preset, tour or mimic tour after prescribed time (menu)

Col/mon changeover 3 levels - menu setup (outdoor only)

Mounting options Wall, ceiling and false ceiling


44


45

INDEX

Aattaching lanyard fixing 20

Ccabling and wiring 7camera

dimensions 41weight 40

configurationinitial 9using serial port 15using the Web Configuration

pages 9connection board

internal dome 27connectors, network 40console input/output specification 39

Ddevices, attaching to network 17dimensions 41

Eenvironmental specification 40external domes

corner mount 32, 33pole mount 32soffit mount 31swan-neck mount 34wall mount 29

Hhardware

specification 39

Iinitial IP properties 9installation

external corner mount 32, 33external pole mount 32external soffit mount 31external swan-neck mount 34external wall mount 29internal ceiling and wall

mount 23internal corner mount 27internal domes 23internal false ceiling mount 25

internal domesceiling and wall mount

installation 23connection board 27corner mount installation 27false ceiling mount 25installation 23

IP domeresetting remotely 37

IP properties 9IP properties, changing

using serial port 16using Web Configuration

pages 13isolated network, preparing 10

Llanyard fixing

attaching 20

Nnetwork

connections 40


46

PPC, preparing for configuration 10power 40

Rregulatory specification 41remote reset of dome 37resolutions specification 39

Ssensor specifications 43specifications 39

codec 39console input/output 39dimensions 41environmental 40power 40regulatory 41resolution 39sensor 43S-Video 39video 39video codec 39weight 40

S-Videospecification 39

Vvideo

codec specification 39specification 39

WWeb Configuration pages 9weight 40


47


Document ID:IU-DOME-MAN001-3.0


IP Dome Camera Hardware Guide - CCTV Center Dome PTZ Camera_manual_eng.pdfIP Dome Camera Hardware...

Documents

Transcript of IP Dome Camera Hardware Guide - CCTV Center Dome PTZ Camera_manual_eng.pdfIP Dome Camera Hardware...