Introduction to FMECA
-
Upload
alana-fulton -
Category
Documents
-
view
40 -
download
1
description
Transcript of Introduction to FMECA
![Page 1: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/1.jpg)
REL103;01202004Slide 1
Introduction to FMECA
What is a FMECA?
– An Analysis technique which facilitates the identification of potential design problems by examining the effects of lower level failures on system operation.
“Obviously, a major malfunction.” - Stephen A Nesbitt NASA Public Affairs Officer
![Page 2: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/2.jpg)
REL103;01202004Slide 2
Why is it Important?
Provides a basis for identifying root failure causes and developing effective corrective actions
Identifies reliability/safety critical components Facilitates investigation of design alternatives at
all stages of the design Provides a foundation for other maintainability,
safety, testability, and logistics analyses
![Page 3: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/3.jpg)
REL103;01202004Slide 3
Definitions
FMECA - Failure Mode, Effects, and Criticality Analysis.
FMEA - Failure Mode and Effects Analysis.
COMPENSATING PROVISIONS - Actions available or that can be taken to lessen or eliminate the effect of a failure on a system.
NEXT HIGHER EFFECT - The consequence a failure mode has upon the operation, function, or status at the next higher level of assembly.
END EFFECT - The consequence a failure mode has upon the operation, function, or status at the highest level of indenture.
![Page 4: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/4.jpg)
REL103;01202004Slide 4
How is it Done?
What are the effects
of part failures on
the board?
What are the effects
of board failures on
the box?
What are the effects
of box failures on
the system?
Note: This is a bottoms up example.
Top down examples are possible.
![Page 5: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/5.jpg)
REL103;01202004Slide 5
Simple Example: Flashlight
This flashlight is for use by special operations forces involved in close combat missions (especially hostage rescue) during low visibility conditions in urban areas. The light is to mounted coaxially with the individual's personal weapon to momentarily illuminate and positively identify targets before they are engaged. The exterior casing including the transparent light aperture are from an existing ruggidized design and can be considered immune to failure.
![Page 6: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/6.jpg)
REL103;01202004Slide 6
Simple Example: Flashlight (cont.)
Item Failure Mode End Effect
bulb dim light flashlight output dimno light no flashlight output
switch stuck closed constant flashlight outputstuck open no flashlight outputintermittent flashlight sometimes will not turn on
contact poor contact flashlight output dimno contact no flashlight outputintermittent flashlight sometimes will not turn on
battery low power flashlight output dimno power no flashlight output
How can it fail?
What is the effect? Note
that Next Higher Effect =
End Effect in this case.
Part
![Page 7: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/7.jpg)
REL103;01202004Slide 7
Severity
SEVERITY classifies the degree of injury, property damage, system damage, and mission loss that could occur as the worst possible consequence of a failure. For a FMECA these are typically graded from I to IV in decreasing severity.
The standard severities defined in MIL-STD1682 may be used or equipment specific severities may be defined with customer concurrence (recommended).
![Page 8: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/8.jpg)
REL103;01202004Slide 8
Simple Example: Flashlight (cont.)
Severity
– Severity I Light stuck in the “on” condition
– Severity II Light will not turn on
– Severity III Degraded operation
– Severity IV No effect
![Page 9: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/9.jpg)
REL103;01202004Slide 9
Simple Example: Flashlight (cont.)
Item Failure Mode End Effect Severity
bulb dim light flashlight output dim IIIno light no flashlight output II
switch stuck closed constant flashlight output Istuck open no flashlight output IIintermittent flashlight sometimes will not turn on III
contact poor contact flashlight output dim IIIno contact no flashlight output IIintermittent flashlight sometimes will not turn on III
battery low power flashlight output dim IIIno power no flashlight output II
![Page 10: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/10.jpg)
REL103;01202004Slide 10
Criticality
CRITICALITY is a measure of the frequency of occurrence of an effect.
– May be based on qualitative judgement or
– May be based on failure rate data
![Page 11: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/11.jpg)
REL103;01202004Slide 11
Simple Example: Flashlight (cont.)
![Page 12: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/12.jpg)
REL103;01202004Slide 12
Simple Example: Flashlight (cont.)
Can circled items be designed out or mitigated?
(There may be others that need to addressed also.)
![Page 13: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/13.jpg)
REL103;01202004Slide 13
Integrated FMECA
FMECAs are often used by other functions such as Maintainability, Safety, Testability, and Logistics.
– Coordinate your effort with other functions up front
– Integrate as many other tasks into the FMECA as possible and as make sense (Testability, Safety, Maintainability, etc.)
Integrating in this way can save considerable cost over doing the efforts separately and will usually produce a better product.
If possible, use the same analyst to accomplish these tasks for the same piece of hardware. This can be a huge cost saver.
![Page 14: Introduction to FMECA](https://reader036.fdocuments.us/reader036/viewer/2022082422/56812cfa550346895d91cafc/html5/thumbnails/14.jpg)
REL103;01202004Slide 14
FMECA Facts and Tips
FMECAs should begin as early as possible
– This allows the analyst to affect the design before it is set in stone.
– If you start early (as you should) expect to have to redo portions as the design is modified.
FMECAs take a lot of time to complete.
FMECAs require considerable knowledge of system operation necessitating extensive discussions with software/hardware Design Engineering and System Engineering.
Spend time developing groundrules with your customer up front.