International Fan Coil Unit I100-90002102[1]
Transcript of International Fan Coil Unit I100-90002102[1]
BUILD YOUR REPUTATION ON OURS
Horizontal SeriesFAN COIL TECHNICAL CATALOG
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com2
Horizontal Series
International Environmental Corporation (IEC) works continually
to improve its products. As a result, the design and specifications
of each product may be changed without notice and may not be
as described herein. Please contact IEC for information regarding
current design and product specif ications. Statements and
other information contained herein are not express warranties
and do not form the basis of any bargain between the parties
but are merely IEC’s opinion or commendation of its products.
Manufacturer’s standard limited warranty applies.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
3
TAbLE OF CONTENTS
3 Table of Contents
4 Portfolio
6 Features & Benefits
7 Unit Model Key
8 Ratings & Listings
9 Air Delivery
10 Electric Heating
11 Motor Data
13 Physical Data
27 Standard Features & Options
32 Piping Packages (Typical)
33 Mechanical Specifications
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com4
Horizontal SeriesPOrTFOLIO
CPY - Horizontal Hideaway with Plenum 200 CFM to 1200 CFMThe Horizontal Hideaway with Plenum (CPY) fan coil unit
provides the same basic features of the CHY plus a return
air plenum for above-ceiling mounting in closets, hallways
or bathroom areas. The CPY design enables the unit to be
adapted to installations requiring return air ducts or to be
used as a return-air plenum with a unit-mounted filter and
filter-rack assembly. CPY units are shipped from the factory
ready for installation with the plenum section in place. No
field fabrication is required. CPY units are designed with
interchangeable panels so that the unit may be modified on
site to accommodate a rear or bottom return. Standard CPY
units are provided with a galvanized finish.
CBY - Horizontal Telescoping Hideaway 200 CFM to 1200 CFMThe Horizontal Telescoping Hideaway (CBY) fan coil unit is
mounted fully-recessed for ceiling-recessed applications. The
CBY’s telescoping frame with hinged panel adapts to any
ceiling type and ensures exact alignment of the panel with
the ceiling. The hinged-bottom panel provides easy access
to all internal components. Standard CBY units are provided
with a galvanized finish on the cabinet and powder-coat
paint finish on the bottom-access panel.
CHY - Horizontal Hideaway 200 CFM to 1200 CFMThe Horizontal Hideaway (CHY) fan coil unit is designed
specifically to meet the many varied requirements for a
ceiling hideaway installation. The low-silhouette styling of
the CHY makes this unit ideally suited for drop-ceiling and
over-closet applications. Standard CHY units are provided
with a galvanized finish.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
5
POrTFOLIO, Cont’d.
CXB - Horizontal Cabinet 200 CFM to 1200 CFMThe Horizontal Cabinet (CXB) fan coil unit is designed
specifically for exposed mounting in hotels, motels,
hospitals, nursing homes, offices or other commercial
establishments. With the CXB, valuable floor space is not
required, and its slim, attractively-styled cabinet blends
with all types of decor. Since there is no requirement for
duct work or structure modifications, the CXB is ideal for
retrofit applications. Standard CXB units are provided with a
powder-coat paint finish.
BHY - Horizontal Hi-Static Hideaway 400 CFM to 1000 CFMThe Horizontal Hi-Static Hideaway (BHY) fan coil unit is
suited for above-ceiling applications with space limitations.
The BHY unit is furnished with larger diameter wheels
to achieve higher static pressures required for ductwork
applications. Standard BHY units are provided with a
galvanized finish.
BPY - Horizontal Hi-Static Hideaway with Plenum 400 CFM to 1000 CFMThe Horizontal Hi-Static Hideaway with Plenum (BPY) fan
coil unit is designed for installations requiring a return-air
plenum with a unit-mounted filter and filter-rack assembly.
The BPY plenum is constructed of galvanized steel and lined
with glass-fiber insulation. BPY units are designed with
interchangeable panels so that the unit may be modified on
site to accommodate a rear or bottom return. Standard BPY
units are provided with a galvanized finish.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com6
Horizontal SeriesFEATurES & bENEFITS
Application Fit• Multiple cabinet choices are available in 7 nominal
CFM sizes for application in a variety of room layouts.
o Horizontal Cabinet units (CXB) with aesthetically
pleasing cabinetry offer capacities that are ideal for
air conditioning in dormitories, small apartments,
schools and many other applications. Front supply,
bottom or rear return are available.
o Horizontal Telescoping Hideaway units with
painted access panel (CBY) allows smooth fit up
to plaster or sheet rock ceilings. Standard units
include bottom louvered return air with the filter
located in the access panel.
o Horizontal Hideaway models (CHY/BHY) units are
installed above the ceiling with or without ducted
supply air and open “soffit” return with an optional
ceiling-mounted filter-grille.
o Horizontal Hideaway models with plenum (CPY/
BPY) units are installed above the ceiling with or
without ducted supply air and ducted return air.
The return air filter is either mounted on the unit
plenum or installed in an optional ceiling filter-
grille.
Design Flexibility• Easy to use ratings program to speed up project
design.
• Standard and high capacity hydronic coils and DX coils
are available to match the heating and cooling loads of
the space.
• Optional powder-paint finish colors and grille
selections will complement most décors (exposed
units).
• CXB and CBY units ordered with optional rear return
are constructed with a solid bottom panel.
• Customizable cabinetry makes these units ideal for
renovation jobs or where special sizes are required to
fit oversized valves and control packages.
• Optional airflow configuration (front supply, bottom
supply, rear return or bottom return) to meet certain
design limitations.
• Outside air connections are available to meet
ventilation requirements and reduce field labor (CXB/
CBY/CPY/BPY).
• Wide variety of factory assembled valve packages to
meet desired controls specifications.
• Optional condensate overflow switch to address latest
building codes where required.
• Wide variety of optional insulation materials are
available to address IAQ concerns.
Ease of Installation• Factory assembled valve packages minimize piping
work at the job site (shipped loose for field mounting).
• Optional unit mounted controls, service switches and
fusing minimize the electrical work required on site.
• Units are tagged at the factory for clear identification
on job site.
• Opposite end connection units may minimize the
piping work on renovation jobs.
Ease of Service• All components are accessible by simply removing the
access panel.
• Filters can be replaced without tools or by opening the
bottom panels on exposed units.
• Blower assembly easily removed from the rear of coil
for service and cleaning.
Quality and Safety• Every unit is tested and inspected at the factory for
trouble free start-up.
• ETL and CETL listed.
• AHRI certified.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
7
uNIT MOdEL KEy
Y • NoneYY • None
• R • 3 Row, AAVS • 4 Row, AAV
CoilConstruction
Y • StdS • SS Wrapper
Code ItemsCode
* Consult factory for 50Hz applications.
** Note that kWs depend on voltage and unit size.
*** Standing in front of the unit, hand is determined by looking into the air supply and assigning the hand to match the location of the cooling coil connections.
Arrangement
56
CHY • Horizontal HideawayCPY • Horizontal Hideaway with PlenumCBY • Horizontal Telescoping HideawayCXB • Horizontal CabinetBHY • Horizontal Hi-Static HideawayBPY • Horizontal Hi-Static Hideaway
with Plenum
02 • 200 CFM03 • 300 CFM04 • 400 CFM06 • 600 CFM08 • 800 CFM10 • 1000 CFM12 • 1200 CFM
Two-pipe Cooling and Heating or Four-pipe Cooling
A 3 RowB • 4 RowD • 2 Row
Voltage
C • 120 VD • 208 VE • 240 VF • 277 VV • 220 V (50)*U • 240 V (50)*
Four-pipe Heating
Y • None6 • 1 Row7 • 2 Row
Voltage
C • 115-1-60
D • 208-1-60
E • 230-1-60
F • 277-1-60
V • 220-1-50*
U • 240-1-50*
Hand***
R • RightL • Left
Voltage
C • 120 VB • 24 V
D • 208 VE • 240 VF • 277 VV • 220 V (50)*
System
Manual Fan Operation
A • Standard Wall Mount (Switch Only)
Valve Cycle Control
G • 2-Pipe Heat OnlyH • 2-Pipe Cool OnlyJ • 2-Pipe Heat and Cool, MCOK • 2-Pipe Heat and Cool, ACOL • 2-Pipe Heat and Cool w/ Aux. Elec. Heat, MCOM • 2-Pipe Heat and Cool w/ Aux. Elec. Heat, ACON • 2-Pipe Cool w/ Total Elec. Heat, MCOP • 2-Pipe Cool w/ Total Elec. Heat, ACOQ • 4-Pipe Heat and Cool, MCOR • 4-Pipe Heat and Cool, ACO
Type
2 • PermanentSplit Capacitor
CHY, BHY
CPY, BPY
CBY
CXB
kW**
AY • 0.50 HY • 5.00BY • 1.00 JY • 6.00CY • 1.50 KY • 7.00DY • 2.00 LY • 8.00FY • 3.00 NY • 10.00GY • 4.00
Stages
Y • Single Stage Only
Coil Connection
Y • NoneS • Same EndO • Opposite End
NOTE: MCO controls (J, L, N, Q) not available with Standard Unit Mount Thermostat
•U • 240 V (50)*
Thermostat
4 • Basic Wall Series
P • 24 V Programmable Wall SeriesN • 24 V Non-Programmable
Wall Series
A • Horizontal Wall SeriesB • Vertical Wall Series
6
6
6
6
5
5
5
MOTOR
05C 2
SIZE
030 4
CONTROLS
07C BP
ELECTRIC HEAT
04aY YC B
VINTAGEUNIT
02Y
01C B
COILS
04Y YA Y
HAND/ARRANGEMENT
06R 5
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com8
Horizontal SeriesrATINGS & LISTINGS
C-ETL US ListingIEC’s Horizontal Series units are
listed by ETL. The C-ETL-US listing
signifies that IEC’s fan coil units
have been examined by ETL and
are in compliance with both the
U.S. and Canadian applicable
standards.
AHRI CertificationIEC’s Horizontal Series units are
certified in compliance with
Air-Conditioning, Heating, and
Refrigeration Institute (AHRI) industry standard AHRI-440 for
room fan coil units. Approved standard ratings are tabulated
below.3061627
HEATING AND COOLING EQUIPMENT
Standard Ratings
Unit Type
Unit Cell Size
Nominal CFM
Cooling Capacity Power Input
Watts PSCTotal MBH
Sensible MBH
CHYCPYCXBCBY
02-A 200 6.0 4.4 87
03-A 300 9.0 6.3 85
04-A 400 12.1 8.8 165
06-A 600 17.3 13.0 225
08-A 800 22.6 16.2 235
10-A 1000 27.5 21.0 305
12-A 1200 32.8 25.0 435
CHYCPYCXBCBY
02-B 200 6.9 4.3 87
03-B 300 9.8 6.5 85
04-B 400 13.8 9.8 145
06-B 600 19.6 14.3 220
08-B 800 25.5 18.8 235
10-B 1000 31.0 22.0 300
12-B 1200 37.2 27.7 425
BHY
04-B 400 16.0 11.6 170
06-B 600 21.8 16.0 205
08-B 800 26.5 19.6 225
10-B 1000 37.2 27.6 355
NoTeS: 1. Ratings are based on 80°F DB and 67°F WB EAT, 45°F EWT, 10°F water temperature rise, high fan speed, motor voltage 115/1/60, and air flow under dry coil conditions.
2. For all application ratings, use IEC’s computer selection program, the quick-selection ratings provided in this catalog, or contact your local IEC representative.
3. For additional information, please consult AHRI’s website at www.ahrinet.org.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
9
AIr dELIvEry
Air Delivery (60 Hz)
Model Coil UnitSize
CFM@ 0.0 eSPFor Fan Speed
High Speed CFM@ eSP Indicated
Low Med High 0.05 0.10 0.15 0.20 0.25 0.30
CHY
3 Row
02 175 195 220 205 185 160 - - -03 250 295 330 300 265 225 170 - -04 220 360 510 480 450 415 370 290 -06 330 540 760 720 670 620 560 475 -08 335 590 870 840 800 760 700 620 -10 490 665 1100 1060 1010 930 845 730 -12 705 950 1425 1370 1310 1240 1160 1055 -
4 Row
02 165 190 215 200 175 140 - - -03 240 285 320 290 250 205 150 - -04 215 305 500 470 440 400 340 240 -06 295 530 745 700 650 590 525 430 -08 330 585 860 825 780 730 665 575 -10 480 655 1085 1040 970 895 800 670 -12 690 930 1400 1345 1280 1205 1115 990 -
CBYCPYCXB
3 Row
02 150 175 190 180 170 145 - - -03 215 270 300 275 250 215 165 - -04 205 275 470 445 415 380 320 250 -06 280 450 690 655 615 560 500 410 -08 335 565 835 800 760 710 650 570 -10 485 630 1045 995 940 880 805 710 -12 540 900 1300 1240 1180 1110 1025 920 840
4 Row
02 145 170 185 180 160 125 - - -03 205 260 290 270 240 195 - - -04 200 270 460 435 400 355 300 210 -06 220 440 675 635 595 535 465 355 -08 325 550 815 780 740 658 615 515 -10 475 615 1020 970 915 850 765 645 -12 530 880 1275 1215 1150 1075 980 850 815
BHY
3 Row
04 515 600 665 630 595 550 500 430 35006 545 705 830 780 725 670 610 550 48008 630 715 930 870 810 750 685 615 54010 1210 1350 1445 1360 1275 1185 1095 1000 880
4 Row
04 505 585 650 620 575 530 465 395 30006 525 680 800 750 700 640 585 520 44008 615 705 905 840 780 720 655 580 49510 1180 1315 1410 1320 1230 1140 1050 945 810
BPY
3 Row
04 485 535 570 540 505 465 420 360 28506 540 640 720 680 635 585 530 460 38508 545 660 800 750 695 640 580 515 44010 1060 1195 1295 1216 1130 1045 960 865 700
4 Row
04 420 525 555 520 485 445 390 330 -06 525 625 700 660 610 560 500 430 34008 535 645 780 725 670 615 555 485 39510 1035 1165 1260 1175 1090 1005 915 810 700
NoTeS: 1. Tabled values are standard CFM at sea level, 70°F with dry coil. 2. Ratings include factory-installed filter and/or grille, where applicable. 3. Consult factory for 50 Hz applications.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com10
Horizontal SeriesELECTrIC HEATING
Electric Heater Selection
Voltage kWUnit Size
02 03 04 06 08 10 12
120 V
0.5 • • - - - - -
1.0 • • • • • - -
1.5 • • • • • - -
2.0 • • • • • • •3.0 - • • • • • •
208 V
0.5 • • - - - - -
1.0 • • • • • - -
1.5 • • • • • - -
2.0 • • • • • • •3.0 - • • • • • •4.0 - - - • • • •5.0 - - - •
Note 6 • • •6.0 - - - •
Note 6•
Note 6 • •8.0 - - - - - •
Note 6•
Note 6
240 V277 V
0.5 • • - - - - -
1.0 • • • • • - -
1.5 • • • • • - -
2.0 • • • • • • •3.0 - • • • • • •4.0 - - - • • • •5.0 - - - •
Note 6 • • •6.0 - - - •
Note 6•
Note 6 • •8.0 - - - - - •
Note 6•
Note 6
10.0 - - - - - - • Note 6
NoTeS: 1. All heaters are single stage and single phase. 2. Heaters over 48 Amps are subdivided and fused. 3. Electric Heating Capacities (BTUH) = Heater kW x 3413. 4. Electric Heater Amperage = (Heater kW x 1000)/Applied
Voltage) 5. Consult factory for 50 Hz applications. 6. High and medium speed only.
Electric Resistance HeatingElectric heaters are available on IEC Horizontal Series fan coil
units for the following applications.
Total Electric HeatTotal electric heat eliminates the requirement for a boiler.
Heating and/or cooling may be available on an individual
basis throughout the year. Two-pipe chilled water is used
for cooling; and the electric heater is used for heating.
Individual room controls can be supplied for either manual
or automatic changeover.
Auxiliary Electric HeatAuxiliary electric heat is ideal for tempering room air
between seasons and during the cooling season when
chilled water is being circulated. Individual room controls
are supplied to provide electric heat only when chilled water
is being circulated. During regular heating season, heating is
provided by hot water being circulated in the system.
ConstructionThe heater coils of high-grade resistance wire are supported
by ceramic insulators on plated steel brackets. These heat
elements are suspended directly in front of the fan outlet
between the blower and the coil. High limit thermal cutouts
protect the heater in the event of air failure. There are many
special applications and control sequences for electric heat.
For special applications, please consult the factory.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
11
MOTOr dATA
Thermal Overload Protection and ETL ListingAll permanently lubricated split-capacitor motors furnished by IEC contain internal thermal-
overload protection. The overload automatically resets when the temperature returns to a
safe limit. Electronics Testing Laboratories, Inc. approves the motor and thermal overload
combination at locked rotor conditions only.
Motor Performance Data - CHY, CPY, CXB, CBY
Voltage Fan SpeedUnit Size 02 03 04 06 08 10 12
Nominal HP 1/30 1/30 1/12 1/12 1/6 (2) 1/12 (2) 1/6
115 V
60 Hz
1 Phase
HighAmps 0.53 0.83 1.40 1.40 2.50 2.80 5.00
Watts 87 85 165 165 235 305 435
MediumAmps 0.31 0.50 0.70 0.72 1.50 1.40 2.80
Watts 55 55 80 80 160 150 305
LowAmps 0.27 0.34 0.45 0.45 1.20 0.90 1.20
Watts 35 35 50 50 120 100 130
208 V
60 Hz
1 Phase
HighAmps 0.48 0.48 0.69 0.69 1.30 1.38 2.60
Watts 86 89 115 130 195 260 340
MediumAmps 0.29 0.29 0.43 0.47 0.69 0.94 1.33
Watts 60 60 89 100 135 190 255
LowAmps 0.15 0.15 0.22 0.24 0.47 0.46 0.94
Watts 28 28 45 48 90 90 180
230 V
60 Hz
1 Phase
HighAmps 0.48 0.48 0.69 0.69 1.30 1.38 2.60
Watts 103 106 135 155 210 290 380
MediumAmps 0.31 0.32 0.45 0.52 0.70 1.00 1.34
Watts 70 73 105 115 150 220 285
LowAmps 0.15 0.15 0.24 0.28 0.50 0.50 1.00
Watts 33 33 53 60 105 110 210
277 V
60 Hz
1 Phase
HighAmps 0.35 0.35 0.69 0.69 0.91 1.38 1.82
Watts 80 80 150 155 240 270 440
MediumAmps 0.26 0.26 0.43 0.43 0.62 0.80 1.20
Watts 64 66 110 110 160 200 300
LowAmps 0.16 0.16 0.25 0.35 0.35 0.25 0.66
Watts 40 43 60 90 90 75 175
NoTeS: 1. Total unit motor Amps and Watts are shown. 2. Consult factory for 50 Hz applications.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com12
Horizontal SeriesMOTOr dATA, Cont’d.
Motor Performance Data - BHY, BPY
Voltage Fan SpeedUnit Size 04 06 08 10
Nominal HP 1/8 1/8 1/8 (2) 1/8
115 V60 Hz
1 Phase
HighAmps 1.70 1.70 1.70 3.40Watts 170 205 225 355
MediumAmps 1.65 1.65 1.70 3.37Watts 160 175 195 345
LowAmps 1.45 1.45 1.45 2.95Watts 135 140 165 290
208 V60 Hz
1 Phase
HighAmps 0.76 0.76 0.76 1.52Watts 135 150 160 280
MediumAmps 0.60 0.66 0.67 1.25Watts 120 130 135 250
LowAmps 0.54 0.57 0.57 1.05Watts 105 110 110 205
230 V60 Hz
1 Phase
HighAmps 0.76 0.76 0.76 1.52Watts 150 160 170 300
MediumAmps 0.58 0.66 0.67 1.30Watts 128 145 135 260
LowAmps 0.55 0.60 0.57 1.05Watts 115 127 127 205
277 V60 Hz
1 Phase
HighAmps 0.64 0.64 0.64 1.28Watts 145 155 170 310
MediumAmps 0.45 0.48 0.54 0.95Watts 125 130 145 265
LowAmps 0.36 0.36 0.39 0.74Watts 90 90 100 195
NoTeS: 1. Total unit motor Amps and Watts are shown. 2. Consult factory for 50 Hz applications.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
13
PHySICAL dATA
CHY - Horizontal Hideaway
AIR VENT
1"(25) SUPPLY DUCTCOLLAR
SUPPLYAIR
MTG. HOLES
RESILIENT MOUNTING GROMMET W/ 3/8"(10) DIA. HOLES (TYP. OF 4)
CHILLED/HOT WATERSUPPLY & RETURNCONNECTIONS
A'
OPTIONAL EXTENDEDDRAIN PAN(SEE NOTE 2)
OPTIONAL DRIP LIPSHIPPED LOOSE
OPTIONAL 5/8"(16) O.D. TELL-TALEDRAIN CONNECTION, AVAILABLE ON
STANDARD AND EXTENDED DRAIN PANS
7/8"(22) O.D. CONDENSATE DRAIN
FLEXIBLE METALCONDUIT
RIGHT SIDE VIEWFRONT VIEW
TOP VIEW
6(152)
1-1/2(38)
B
A
3(76)
2-1/4(64)
1-1/8(29)
1(25)
H
E 3/4(19)
3/4(19)
16(406)
G F
17-1/2(445)
8-3/8(213)
1(25)
D'
7/8(22)
JUNCTION BOX
(REMOTE MOUNT)
(NOTE 5)
4(102)
4(102)
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B D’ e F G H Blower Motor
CHY02 21-1/4 (540) 31-1/4 (794) 16 (406) 13 (330) 18-1/4 (464) 6-1/4 (159) 8-3/4 (222) 19-3/4 (502) 1 1 36CHY03 25-1/4 (641) 36-1/4 (921) 20 (508) 14 (356) 22-1/4 (565) 6-1/4 (159) 8-3/4 (222) 23-3/4 (603) 1 1 39CHY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 2 1 49CHY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 2 1 59CHY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 2 1 64CHY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 4 2 95CHY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 13 (330) 62-1/4 (1581) 7-1/2 (191) 10 (254) 63-3/4 (1619) 4 2 107
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip recommended. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com14
Horizontal SeriesPHySICAL dATA, Cont’d.
CHY - Horizontal Hideaway with Electric Heat
RIGHT SIDE VIEWFRONT VIEW
TOP VIEW
CONTROL BOX(REMOTE MOUNT)
ELECTRIC STRIPHEATER ELEMENT
STRIP HEATERHIGH LIMIT
FLEXIBLE METALCONDUIT
7/8"(22) O.D.CONDENSATE DRAIN
OPTIONAL 5/8"(16) O.D.
TELL-TALE DRAIN CONNECTION,
AVAILABLE ON STANDARD AND
EXTENDEDDRAIN PANS
OPTIONAL DRIP LIPSHIPPED LOOSE(NOTE 5)
OPTIONAL EXTENDEDDRAIN PAN (SEE NOTE 2)
A'
CHILLED/HOT WATERSUPPLY & RETURNCONNECTIONS
RESILIENT MOUNTING GROMMETW/ 3/8"(10) DIA. HOLES (TYP. OF 4)
MTG. HOLES
AIRSUPPLY
1" SUPPLY DUCT
COLLAR
VENTAIR
6(152)
1-1/2(38)
1-1/8(29)
2-1/4(64)
AB
E
1(25)
D'
21-1/2(546)
12-3/8(314)
1(25)
G F
7/8(22)
16(406)
H3/4(19)
3/4(19)
3(76)
6 (152)STD.
5-3/8(137)STD.
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B D’ e F G H Blower Motor
CHY02 21-1/4 (540) 31-1/4 (794) 16 (406) 13 (330) 18-1/4 (464) 6-1/4 (159) 8-3/4 (222) 19-3/4 (502) 1 1 38CHY03 25-1/4 (641) 36-1/4 (921) 20 (508) 14 (356) 22-1/4 (565) 6-1/4 (159) 8-3/4 (222) 23-3/4 (603) 1 1 41CHY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 2 1 51CHY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 2 1 61CHY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 2 1 66CHY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 4 2 97CHY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 13 (330) 62-1/4 (1581) 7-1/2 (191) 10 (254) 63-3/4 (1619) 4 2 109
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip recommended. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
15
PHySICAL dATA, Cont’d.
CPY - Horizontal Hideaway with Plenum
15-1/4(387)
11-3/8(289)
FILTER REMOVAL
FILTER REMOVAL
10-1/2(267)
20(508)
19(483)
7/8(22)
FG
1(25)
1" (25) SUPPLY
DUCT COLLAR
SUPPLYAIR
3/4(19)
E
A 16(406)
1-1/2(38)
1-1/8(29) C
2-1/4(57) B 3
(76)MTG. HOLES
RESILIENT MOUNTING GROMMET W/ 3/8" (10) DIA. HOLES (TYP. OF 4) CHILLED/HOT WATER
SUPPLY & RETURNCONNECTIONS
D'
A'
OPTIONALEXTENDEDDRAIN PAN(SEE NOTE 2)
OPTIONAL DRIP LIPSHIPPED LOOSE(NOTE 5)
AIR VENT
REAR ACCESSPANEL
1"(25) FILTER
1" (25) RETURNDUCTCOLLAR
1" (25) FILTER
FILTERRETAINERCLIP
BOTTOM ACCESS
PANEL
CONDENSATE7/8" (22) O.D.
DRAIN
RETURNAIR
AIRRETURN
RIGHT SIDE VIEWFRONT VIEW
TOP VIEW
OPTIONAL 5/8" (16) O.D. TELL-TALEDRAIN CONNECTION, AVAILABLE ON
STANDARD AND EXTENDED DRAIN PANS
HREAR MTG. HOLES
JUNCTION BOX INSULATED PLENUM
1-1/2(38)
1(25)
3/4(19)
OPTIONAL REAR RETURN
3
3-1/4 (83)
4(102)
3(76)
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B C D’ e F G H Blower Motor
CPY02 21-1/4 (540) 31-1/4 (794) 16 (406) 18-1/4 (464) 13 (330) 19-3/4 (502) 6-1/4 (159) 8-3/4 (222) 15-3/8 (391) 1 1 55CPY03 25-1/4 (641) 36-1/4 (921) 20 (508) 22-1/4 (565) 14 (356) 23-3/4 (603) 6-1/4 (159) 8-3/4 (222) 19-3/8 (883) 1 1 60CPY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 28-1/4 (718) 15 (381) 29-3/4 (756) 6-1/4 (159) 8-3/4 (222) 25-3/8 (645) 2 1 70CPY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 33-1/4 (845) 10 (254) 34-3/4 (883) 7-1/2 (190) 10 (254) 30-3/8 (772) 2 1 82CPY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 40-1/4 (1022) 17 (432) 41-3/4 (1060) 7-1/2 (190) 10 (254) 37-3/8 (949) 2 1 95CPY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 54-1/4 (1378) 11 (279) 55-3/4 (1416) 7-1/2 (190) 10 (254) 51-3/8 (1305) 4 2 135CPY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 62-1/4 (1581) 13 (330) 63-3/4 (1619) 7-1/2 (190) 10 (254) 59-3/8 (1508) 4 2 154
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip recommended. 6. Threaded fittings must be field tightened and leak tested. 7. Control box size and position may vary (consult factory).
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com16
Horizontal SeriesPHySICAL dATA, Cont’d.
CPY - Horizontal Hideaway with Plenum with Electric Heat
FRONT VIEW RIGHT SIDE VIEW
ELECTRICAL KNOCKOUTSIN TOP & BOTTOM OFCONTACTOR BOX
CONTROLBOX
STRIP HEATERHIGH LIMIT
ELEMENTSTRIP HEATERELECTRIC
3-1/4(83)
3/4(19)
RETURNAIR
INSULATED PLENUM
REAR MTG. HOLESH 1-1/2
(38)
7/8" (22) O.D.CONDENSATIONDRAIN
1" (25) FILTER
REAR ACCESS
AIR VENT
OPTIONAL DRIP LIPSHIPPED LOOSE(NOTE 5)
CHILLED/HOTWATER SUPPLY &RETURN CONNECTIONS
RESILIENT MOUNTING GROMMET W/ 3/8" (10) DIA. HOLES (TYP. OF 4)
1(25)
16(406)
3/4(19)
3/4(19)
AIRSUPPLY
1" (25)SUPPLY
DUCTCOLLAR
7/8(22)
23(584)
24(610)
10-1/2(267)
FILTER REMOVAL
11-3/8(289)
19-1/4(489)
FILTER REMOVAL
D'
A'
OPTIONAL EXTENDEDDRAIN PAN (SEE NOTE 2)
COLLARDUCT1" (25) RETURN
1" (25) FILTER
FILTERRETAINERCLIP
BOTTOM ACCESS
PANEL
AIRRETURN
OPTIONAL 5/8" (16) O.D.
TELL-TALEDRAIN
CONNECTION, AVAILABLE ON
STANDARD AND EXTENDED
DRAIN PANS
1-1/2(38) 1-1/8
(29) C
2-1/4(57) B 3
(76)A
FRONT MTG. HOLES
TOP VIEW OPTIONAL REAR RETURN
FG
5-3/8(137)STD.
6(152)STD.
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B C D’ e F G H Blower Motor
CPY02 21-1/4 (540) 31-1/4 (794) 16 (406) 18-1/4 (464) 13 (330) 19-3/4 (502) 6-1/4 (159) 8-3/4 (222) 15-3/8 (391) 1 1 57CPY03 25-1/4 (641) 36-1/4 (921) 20 (508) 22-1/4 (565) 14 (356) 23-3/4 (603) 6-1/4 (159) 8-3/4 (222) 19-3/8 (883) 1 1 62CPY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 28-1/4 (718) 15 (381) 29-3/4 (756) 6-1/4 (159) 8-3/4 (222) 25-3/8 (645) 2 1 72CPY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 33-1/4 (845) 13 (330) 34-3/4 (883) 7-1/2 (190) 10 (254) 30-3/8 (772) 2 1 84CPY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 40-1/4 (1022) 17 (432) 41-3/4 (1060) 7-1/2 (190) 10 (254) 37-3/8 (949) 2 1 97CPY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 54-1/4 (1378) 11 (279) 55-3/4 (1416) 7-1/2 (190) 10 (254) 51-3/8 (1305) 4 2 137CPY12 65-1/4 (1657) 75-1/4 (1911) 60 (1524) 62-1/4 (1581) 13 (330) 63-3/4 (1619) 7-1/2 (190) 10 (254) 59-3/8 (1508) 4 2 156
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip recommended. 6. Threaded fittings must be field tightened and leak tested. 7. Control box size and position may vary (consult factory).
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
17
PHySICAL dATA, Cont’d.
CBY - Horizontal Telescoping Hideaway
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW
(TYPICAL BOTH SIDES)PARTIAL REAR VIEW
1-1/2(38)KNOCKOUT (TYPICAL)
7/8"(22)KNOCKOUT
DRAIN CONNECTION7/8"(22) O.D. CONDENSATE AIR
RETURN1"(25) FILTERAIR GRILLE &STAMPED RETURN
DUCT COLLAR1"(25) SUPPLY
F
1-1/4(32)
24(610)
1-1/2(38)
20-3/4(527)
1-1/2(38)
D
14(356)MAX.
12(305)MIN.
11-1/4(286)
A
6-1/8(156)
B C1-1/2(38) 1-1/2
(38)
CHILLED/HOT WATER SUPPLY& RETURN CONNECTION
RESILIENT MOUNTINGGROMMETS WITH 3/8"(10)DIA. HOLE (TYP. OF 4)
OPTIONAL "L" SHAPE DRIPLIP, SHIPPED LOOSE (NOTE 5)
JUNCTION BOX
26(660)
1(25)
1(25)
1-1/2(38)
20-3/4(527)
1-1/2(38)
1(25)
1(25)
E
6-1/8(156)
AIR
SUPPLY
HINGEDBOTTOM RETURN
AIR PANEL
OPTIONALDUCTEDREAR RETURN
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A B C D e F Blower Motor
CBY02 35 (889) 16 (406) 12-3/4 (324) 37 (940) 32 (813) 6 (152) 1 1 115CBY03 35 (889) 20 (508) 8-3/4 (222) 37 (940) 32 (813) 6 (152) 1 1 120CBY04 41 (1041) 26 (660) 8-3/4 (222) 43 (1092) 38 (965) 6 (152) 2 1 135CBY06 53 (1346) 31 (787) 15-3/4 (400) 55 (1397) 50 (1270) 7 (178) 2 1 150CBY08 53 (1346) 38 (965) 8-3/4 (222) 55 (1397) 50 (1270) 7 (178) 2 1 155CBY10 75 (1905) 52 (1321) 16-3/4 (425) 77 (1956) 72 (1829) 7 (178) 4 2 227CBY12 75 (1905) 60 (1524) 8-3/4 (222) 77 (1956) 72 (1829) 7 (178) 4 2 241
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Internal factory valve packages and drains may not align w/cabinet knockouts. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com18
Horizontal SeriesPHySICAL dATA, Cont’d.
CBY - Horizontal Telescoping Hideaway with Electric Heat
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW
ELECTRIC STRIPHEATER ELEMENT
STRIP HEATERHIGH LIMIT
(TYPICAL BOTH SIDES)PARTIAL REAR VIEW
1-1/2(38)KNOCKOUT
(TYPICAL)
7/8"(22)KNOCKOUT
7/8"(22) O.D. CONDENSATE
DRAIN CONNECTION
RETURNAIR
STAMPED RETURNAIR GRILLE &1"(25) FILTER
DUCT COLLAR1"(25) SUPPLY
F
1-1/4(32)
1-1/2(38)
20-3/4(527)
1-1/2(38)
D
14(356)MAX.
12(305)MIN.
11-1/4(286)
A6-1/8(156) B C
1-1/2(38)
1-1/2(38)
CHILLED/HOT WATER SUPPLY& RETURN CONNECTION
RESILIENT MOUNTINGGROMMETS WITH 3/8"(19)DIA. HOLE (TYP. OF 4)
OPTIONAL "L" SHAPE DRIPLIP, SHIPPED LOOSE (NOTE 5)
CONTROL BOX
26(660)
1(25) 1-1/2
(38)
20-3/4(527)
1-1/2(38)
1(25)
1(25)
E
6-1/8(156)
AIR
SUPPLY
HINGEDBOTTOM RETURN
AIR PANEL
24(610)
OPTIONALDUCTEDREARRETURN
1(25)
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A B C D e F Blower Motor
CBY02 35 (889) 16 (406) 12-3/4 (324) 37 (940) 32 (813) 6 (152) 1 1 117CBY03 35 (889) 20 (508) 8-3/4 (222) 37 (940) 32 (813) 6 (152) 1 1 122CBY04 41 (1041) 26 (660) 8-3/4 (222) 43 (1092) 38 (965) 6 (152) 2 1 137CBY06 53 (1346) 31 (787) 15-3/4 (400) 55 (1397) 50 (1270) 7 (178) 2 1 152CBY08 53 (1346) 38 (965) 8-3/4 (222) 55 (1397) 50 (1270) 7 (178) 2 1 157CBY10 75 (1905) 52 (1321) 16-3/4 (425) 77 (1956) 72 (1829) 7 (178) 4 2 229CBY12 75 (1905) 60 (1524) 8-3/4 (222) 77 (1956) 72 (1829) 7 (178) 4 2 243
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
19
PHySICAL dATA, Cont’d.
CBY - Horizontal Telescoping Hideaway with Bottom Supply
FRONT VIEW
(TYPICAL BOTH SIDES)PARTIAL REAR VIEW
1-1/2(38) KNOCKOUT
(TYPICAL)
7/8"(22)KNOCKOUT
D
14"(356)MAX.
12"(305)MIN.
11-1/4(286)
A
30-3/4 (781)34(864)
RIGHT SIDE VIEW
HINGEDBOTTOM RETURN
AIR PANEL
1-1/2(38)
AIR GRILLE &AIR 1"(25) FILTER
STAMPED RETURN
7/8"(22) O.D.
RETURN
1-1/2(38)
DRAIN CONNECTION
SUPPLYAIR
STAMPED SUPPLYAIR GRILLE
E
36(914)
30-3/4(781)
1(25)
1-1/2 (38)
1(25) TOP VIEW
1(25) 1-1/2(38) JUNCTION BOX
1(25)
1-1/2 (38)
RESILIENT MOUNTING GROMMETS WITH 3/8"(10) DIA. HOLE (TYP. OF 4)
OPTIONAL "L" SHAPE DRIP LIP, SHIPPED LOOSE (NOTE 5)
CHILLED/HOT WATER SUPPLY& RETURN CONNECTION
6"(152)
1-1/2(38)
CONDENSATE
OPTIONALDUCTEDREAR RETURN
E1-1/2 (38) 1-1/2 (38)
Unit ModelDimensions - Inches (Millimeters) Quantity/Unit
Unit Weight*A D e F Blower Motor
CBY02 35 (889) 37 (940) 32 (813) 6 (152) 1 1 115CBY03 35 (889) 37 (940) 32 (813) 6 (152) 1 1 120CBY04 41 (1041) 43 (1092) 38 (965) 6 (152) 2 1 135CBY06 53 (1346) 55 (1397) 50 (1270) 7 (178) 2 1 150CBY08 53 (1346) 55 (1397) 50 (1270) 7 (178) 2 1 155CBY10 75 (1905) 77 (1956) 72 (1829) 7 (178) 4 2 227CBY12 75 (1905) 77 (1956) 72 (1829) 7 (178) 4 2 241
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Internal factory valve packages and drains may not align w/cabinet knockouts. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com20
Horizontal SeriesPHySICAL dATA, Cont’d.
CBY - Horizontal Telescoping Hideaway with Bottom Supply with Electric Heat
FRONT VIEW
(TYPICAL BOTH SIDES)PARTIAL REAR VIEW
1-1/2(38) KNOCKOUT (TYPICAL)7/8"(22) KNOCKOUT
D
14"(356)MAX.
12"(305)MIN.
11-1/4(286)
A1-1/2(38) E 1-1/2
(38)
30-3/4(781)
34(864)
RIGHT SIDE VIEW
HINGEDBOTTOM RETURN
AIR PANEL
1-1/2(38)
STAMPED RETURNAIR GRILLE &1"(25) FILTER
AIRRETURN
1-1/2(38)
SUPPLYAIR
STAMPED SUPPLYAIR GRILLE
E
36(914)
30-3/4(781)
1(25)
1-1/2(38)
1(25)
1-1/2(38)
TOP VIEW
1(25)1-1/2(38)
1(25)
1-1/2(38)
RESILIENT MOUNTINGGROMMETS WITH 3/8"(10) DIA. HOLE (TYP. OF 4)
OPTIONAL "L" SHAPE DRIP LIP, SHIPPED LOOSE (NOTE 5)
CHILLED/HOT WATER SUPPLY & RETURN CONNECTION
6"(152)
STRIP HEATERHIGH LIMIT HEATER ELEMENT
ELECTRIC STRIPCONTROL BOX
7/8"(22) O.D. CONDENSATEDRAIN CONNECTION
*DRAWING NOT TO SCALE*
OPTIONALDUCTEDREAR RETURN
Unit ModelDimensions - Inches (Millimeters) Quantity/Unit
Unit Weight*A D e Blower Motor
CBY02 35 (889) 37 (940) 32 (813) 1 1 117CBY03 35 (889) 37 (940) 32 (813) 1 1 122CBY04 41 (1041) 43 (1092) 38 (965) 2 1 137CBY06 53 (1346) 55 (1397) 50 (1270) 2 1 152CBY08 53 (1346) 55 (1397) 50 (1270) 2 1 157CBY10 75 (1905) 77 (1956) 72 (1829) 4 2 229CBY12 75 (1905) 77 (1956) 72 (1829) 4 2 243
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Internal factory valve packages and drains may not align w/cabinet knockouts. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
21
PHySICAL dATA, Cont’d.
CXB - Horizontal Cabinet
SUPPLYAIR
APPROX.REF.
1-1/2(38)
RETURNAIR
7/8" (22) O.D. CONDENSATEDRAIN CONNECTION
AIRVENT
RESILIENT MOUNTINGGROMMETS WITH 3/8" (10)DIA. HOLE (TYP. OF 4)
2(51)
2(51)
2(51)
SUPPLY AIR GRILLESTANDARD STAMPED
OPTIONAL "L" SHAPEDDRIP LIP, SHIPPEDLOOSE (NOTE 5)
CHILLED/HOT WATERSUPPLY & RETURN
CONNECTIONS
STAMPED RETURNAIR GRILLE &1" (25) FILTER
RIGHT SIDE VIEWFRONT VIEW
TOP VIEW
REMOVABLE HINGEDR.A./ACCESS
PANEL
18(457)
Ø7/8" (22) KNOCKOUT(TYP. OF 2)
Ø1-1/2"(38) KNOCKOUT(TYP. OF 5)
PARTIAL REAR VIEW(TYPICAL BOTH SIDES)
2(51)
CONTROL BOX
5-3/4(146)
AIRRETURN
1" (25) FILTERAIR GRILLE &STAMPED RETURNOPTIONAL
OPTIONAL
LOCATION
STANDARD
C B C
E
A
FG
3 1/2(89)
23-1/2(597)
Unit ModelDimensions - Inches (Millimeters) Quantity/Unit Unit
Weight*A B C e F G Blower MotorCXB02 38 (965) 17-1/8 (435) 10-7/16 (265) 34 (864) 5-3/4 (146) 11 (279) 1 1 98CXB03 42 (1067) 21-1/2 (546) 10-1/4 (260) 38 (965) 5-3/4 (146) 11 (279) 1 1 118CXB04 48 (1219) 25-7/8 (657) 11-1/16 (281) 44 (1118) 5-3/4 (146) 11 (279) 2 1 126CXB06 53 (1346) 34-5/8 (879) 9-3/16 (233) 49 (1245) 6-3/4 (171) 12 (305) 2 1 168CXB08 60 (1524) 39 (991) 10-1/2 (267) 56 (1422) 6-3/4 (171) 12 (305) 2 1 176CXB10 74 (1880) 52-1/8 (1324) 10-15/16 (262) 70 (1778) 6-3/4 (171) 12 (305) 4 2 215CXB12 82 (2083) 60-7/8 (1546) 10-9/16 (268) 78 (1981) 6-3/4 (171) 12 (305) 4 2 245
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Internal factory valve packages and drains may not align w/cabinet knockouts. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com22
Horizontal SeriesPHySICAL dATA, Cont’d.
CXB - Horizontal Cabinet with optional Electric Heat
SUPPLYAIR
APPROX.REF.
1-1/2(38)
RETURNAIR
7/8" (22) O.D.
DRAIN CONNECTION
AIR VENT
RESILIENT MOUNTINGGROMMETS WITH 3/8" (10)DIA. HOLE (TYP. OF 4)
2(51)
2(51)
2(51)
SUPPLY AIR GRILLESTANDARD STAMPED
OPTIONAL "L" SHAPEDDRIP LIP, SHIPPEDLOOSE
CHILLED/HOT WATERSUPPLY & RETURN
CONNECTIONS
STAMPED RETURNAIR GRILLE &1" (25) FILTER
ELECTRIC STRIPHEATER ELEMENT
RIGHT SIDE VIEWFRONT VIEW
TOP VIEW
REMOVABLE HINGEDR.A./ACCESS
PANEL
18(457)
Ø7/8" (22) KNOCKOUT(TYP. OF 2)
Ø1-1/2"(38) KNOCKOUT(TYP. OF 5)
PARTIAL REAR VIEW(TYPICAL BOTH SIDES)
2(51)
5-3/4(146)
1" (25) FILTERAIR GRILLE &STAMPED RETURN
OPTIONAL
OPTIONAL
STANDARD
C B C
E
A
FG
3-1/2(89)
(NOTE 5)
23-1/2(597)
CONDENSATE
AIRRETURNOPTIONAL
LOCATION
CONTROL BOX
Unit ModelDimensions - Inches (Millimeters) Quantity/Unit Unit
Weight*A B C e F G Blower MotorCXB02 38 (965) 17-1/8 (435) 10-7/16 (265) 34 (864) 5-3/4 (146) 11 (279) 1 1 100CXB03 42 (1067) 21-1/2 (546) 10-1/4 (260) 38 (965) 5-3/4 (146) 11 (279) 1 1 120CXB04 48 (1219) 25-7/8 (657) 11-1/16 (281) 44 (1118) 5-3/4 (146) 11 (279) 2 1 128CXB06 53 (1346) 34-5/8 (879) 9-3/16 (233) 49 (1245) 6-3/4 (171) 12 (305) 2 1 170CXB08 60 (1524) 39 (991) 10-1/2 (267) 56 (1422) 6-3/4 (171) 12 (305) 2 1 178CXB10 74 (1880) 52-1/8 (1324) 10-15/16 (262) 70 (1778) 6-3/4 (171) 12 (305) 4 2 217CXB12 82 (2083) 60-7/8 (1546) 10-9/16 (268) 78 (1981) 6-3/4 (171) 12 (305) 4 2 247
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Internal factory valve packages and drains may not align w/cabinet knockouts. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
23
PHySICAL dATA, Cont’d.
BHY - Horizontal Hi-Static Hideaway
11-1/4(286)
19-3/4(502)
8-3/8(213)7/8
(22)
FG
1(25)
AIR VENT
1"(25) SUPPLY
DUCT COLLAR
SUPPLYAIR
E 3/4(19)
H
G
A
16(406)
1-1/2(38)
6(152)
1-1/8(29)
E
2-1/4(57)
B 3(76)
A
1(25)
MTG. HOLES
RESILIENT MOUNTING GROMMET W/ 3/8"(10) DIA. HOLES (TYP. OF 4)
CHILLED/HOT WATERSUPPLY & RETURNCONNECTIONS
D'OPTIONAL EXTENDED DRAIN PAN (SEE NOTE 2)
OPTIONAL DRIP LIPSHIPPED LOOSE(NOTE 5)
OPTIONAL 5/8"(16) O.D.
TELL-TALE DRAIN CONNECTION,
AVAILABLE ON STANDARD AND
EXTENDED DRAIN PANS
JUNCTION BOX (REMOTE MOUNT)
RIGHT SIDE VIEWFRONT VIEW
TOP VIEW
7/8"(22) O.D. CONDENSATE DRAIN
FLEXIBLE METAL CONDUIT
A'
*DRAWING NOT TO SCALE*
3/4(19)
4(102)
4(102)
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B D’ e F G H Blower Motor
BHY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 2 1 62BHY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 2 1 73BHY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 2 1 82BHY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 4 2 128
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip recommended. 6. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com24
Horizontal Series
BHY - Horizontal Hi-Static Hideaway with Electric Heat
TOP VIEW
FRONT VIEWRIGHT SIDE VIEW
STRIP HEATER
CONDUITFLEXIBLE METAL
7/8"(22) O.D. CONDENSATE DRAIN
OPTIONAL 5/8"(16) O.D.
TELL-TALEDRAIN
CONNECTION,AVAILABLE
ON STANDARD AND EXTENDED
DRAIN PANS
OPTIONAL DRIP LIP (NOTE 5) SHIPPED LOOSE
DRAIN PAN (SEE NOTE 2)OPTIONAL EXTENDED
D'
CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS
W/ 3/8"(10) DIA. HOLES (TYP. OF 4)RESILIENT MOUNTING GROMMET
MTG. HOLES
1(25)
A
3(76)B2-1/4
(57)
E1-1/8(29)
6(152)
1-1/2(38)
16(406)
A
G
H
3/4(19)
E
AIRSUPPLY
VENTAIR
G F
12-3/8(314)
23-3/4(603)1
(25)
1"(25) SUPPLY
DUCT COLLAR
7/8(22)
11-1/4(286)
A'
3/4(19)
CONTROL BOX(REMOTE MOUNT)
6(152)STD.
5-3/8(137)STD.
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B D’ e F G H Blower Motor
BHY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 2 1 64BHY06 36-1/4 (921) 43-1/4 (1099) 31 (787) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 2 1 75BHY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 2 1 84BHY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 4 2 130
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip recommended. 6. Threaded fittings must be field tightened and leak tested.
PHySICAL dATA, Cont’d.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
25
PHySICAL dATA, Cont’d.
BPY - Horizontal Hi-Static Hideaway with Plenum
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW
RETURNAIR
AIRRETURN
1(25)REAR MTG. HOLES
H
2(51)
DRAIN
7/8"(22) O.D.CONDENSATE
BOTTOM ACCESS
PANELCLIPRETAINERFILTER
1"(25) FILTER
1"(25) RETURNDUCTCOLLAR
1"(25) FILTER
PANELACCESSREAR
AIR VENT
1/2(13)
OPTIONAL 5/8"(16) O.D. TELL-TALEDRAIN CONNECTION, AVAILABLE ONSTANDARD AND EXTENDED DRAIN PANS
SHIPPED LOOSE
OPTIONAL DRIP LIP
OPTIONALEXTENDEDDRAIN PAN (SEE NOTE 2)
D'
CONNECTIONSSUPPLY & RETURNCHILLED/HOT WATERW/ 3/8"(10) DIA. HOLES (TYP. OF 4)
RESILIENT MOUNTING GROMMET
MTG. HOLES
1(25)
A
3(76)B2-1/4
(57)
C1-1/8(29)
1-1/2(38)
16(406)A
E3/4(19)C
AIRSUPPLY
1"(25) SUPPLY
DUCTCOLLAR
G F
7/8(22)
21-1/2(546)
22-1/2(572)
PLENUM HANGER CLIPS (SEE NOTE 4)
FILTERREMOVAL
REMOVALFILTER
13-15/16(354)
12-3/4(324)
INSULATED PLENUMJUNCTION BOX
18(457)
3 (76)
A'
(NOTE 6)
OPTIONAL REAR RETURN
3/4(19)
4(102)
3(76)
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B C D’ e F G H Blower Motor
BPY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 28-1/4 (718) 15 (381) 29-3/4 (756) 6-1/4 (159) 8-3/4 (223) 30-1/4 (768) 2 1 84BPY06 36-1/4 (921) 43-1/4 (1099) 34 (787) 33-1/4 (845) 10 (254) 34-3/4 (883) 7-1/2 (190) 10 (254) 35-1/4 (895) 2 1 97BPY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 40-1/4 (1022) 17 (432) 41-3/4 (1060) 7-1/2 (190) 10 (254) 42-1/4 (1073) 2 1 110BPY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 54-1/4 (1378) 11(279) 55-3/4 (1416) 7-1/2 (190) 10 (254) 56-1/4 (1429) 4 2 163
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Plenum hanger clip location may vary depending on unit accessories. 5. Product specifications are subject to change without notice. 6. Drip lip recommended. 7. Control box size and position may vary (consult factory). 8. Threaded fittings must be field tightened and leak tested.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com26
Horizontal Series
BPY - Horizontal Hi-Static Hideaway with Plenum with Electric Heat
TOP VIEW
FRONT VIEW RIGHT SIDE VIEW
MAX.
CONTACTOR BOXIN TOP & BOTTOM OFELECTRICAL KNOCKOUTS
CONTROLBOX
STANDARD AND EXTENDED
ELEMENTSTRIP HEATERELECTRIC
3 (76)CLIPS (SEE NOTE 4)PLENUM HANGER
(SEE NOTE 2)DRAIN PAN
3/4(19)
RETURNAIR
AIRRETURN
INSULATED PLENUM
1(25)REAR MTG. HOLES
H
2(51)
DRAIN
7/8"(22) O.D.CONDENSATE
BOTTOM ACCESS PANEL FILTERRETAINERCLIP
1"(25) FILTER
1"(25) RETURNDUCTCOLLAR
1"(25) FILTER PANELACCESSREAR
AIR VENT
1/2(13)
CONNECTION,AVAILABLE ONTELL-TALE DRAINOPTIONAL 5/8"(16) O.D.
SHIPPED LOOSE
OPTIONAL DRIP LIP
EXTENDEDOPTIONAL
A'
D'
CONNECTIONSSUPPLY & RETURNCHILLED/HOT WATERW/ 3/8"(10) DIA. HOLES (TYP. OF 4)
RESILIENT MOUNTING GROMMET
MTG. HOLES
1(25)
A
3(76)B2-1/4
(57)
C1-1/8(29)
16(406)A
E3/4(19)
3/4(19)
AIRSUPPLY
1"(25) SUPPLY
DUCT COLLAR
G F
7/8(22)
25-1/2(648)
26-1/2(673)
FILTERREMOVAL
REMOVALFILTER
12-3/4(324)
13-15/16(354)
22(559)
DRAIN PANS
1-1/2(38)
(NOTE 6)
OPTIONAL REAR RETURN
5-3/8(137)STD.
6(152)STD.
Unit Model
Dimensions - Inches (Millimeters) Quantity/Unit Unit Weight*A A’ B C D’ e F G H Blower Motor
BPY04 31-1/4 (794) 43-1/4 (1099) 26 (660) 28-1/4 (718) 15 (381) 29-3/4 (756) 6-1/4 (159) 8-3/4 (223) 30-1/4 (768) 2 1 86BPY06 36-1/4 (921) 43-1/4 (1099) 34 (787) 33-1/4 (845) 10 (254) 34-3/4 (883) 7-1/2 (190) 10 (254) 35-1/4 (895) 2 1 99BPY08 43-1/4 (1099) 57-1/4 (1454) 38 (965) 40-1/4 (1022) 17 (432) 41-3/4 (1060) 7-1/2 (190) 10 (254) 42-1/4 (1073) 2 1 112BPY10 57-1/4 (1454) 65-1/4 (1657) 52 (1321) 54-1/4 (1378) 11 (279) 55-3/4 (1416) 7-1/2 (190) 10 (254) 56-1/4 (1429) 4 2 165
NoTeS: * Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. RH shown, LH opposite. 2. Optional drip lip not required with optional extended drain pan. 3. All dimensions are +/- 1/4" (6). 4. Plenum hanger clip location may vary depending on unit accessories. 5. Product specifications are subject to change without notice. 6. Drip lip recommended. 7. Control box size and position may vary (consult factory). 8. Threaded fittings must be field tightened and leak tested.
PHySICAL dATA, Cont’d.
Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IeC web site for
up to date drawings.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
27
STANdArd FEATurES & OPTIONS
Features And options StandardFactory
Installed option
Field Installed option
Factory Special Quote
Air Flow ArrangementFront Supply/Rear Return (CHY, BHY) X – – –Front Supply/Rear or Bottom Return (CPY, BPY, CBY, CXB) X (Bottom) X (Rear) – –Coils2 Rows 2-Pipe (CHY, CPY, CBY, CXB) – X – –3 Rows 2-Pipe (CHY, BHY, CPY, BPY, CBY, CXB) X – – –4 Rows 2-Pipe (CHY, BHY, CPY, BPY, CBY, CXB) – X – –3/1, 3/2, 4/1 Rows 4-Pipe (CHY, BHY, CPY, BPY, CBY, CXB) – X – –Manual Air Vent X – – –Automatic Air Vent – X – –DX Coils – X – –Steam Coils – X – XConnectionRight or Left (Same End) X – – –Right or Left (Opposite End) – X – –Drain PanGalvanized Internally Coated with 2-part closed Cell Foam X – – –Stainless Steel Externally Coated – X – –Drip Lip (recommended with motorized valves) – – X –Extended Drain Pans (CHY, CPY, BHY, BPY) – X – –Secondary Drain Connection – X – vFin MaterialAluminum with Galvanized End Sheets X – – –Copper with Stainless End Sheets & Bottom Coil Baffle – X – XNichrome Wire Strip electric Heater (Total and Auxiliary) – X – –Filters1" Throwaway non-woven synthetic filter X – – –1" Permanent – X – –1" Pleated MERV 8 – X – –Insulation1/2" Standard Fiberglass X – – –1/2" Premium IAQ Fiberglass – X – X1/2" Foil Face – X – –1/4" Closed Cell – X – –Motor TypePSC Motors with Quick Connect Plug X – – –Motor Voltage120/1/60 3-Speed X – – –208/230/277/1/60 3-Speed (Optional Voltage) – X – –Supply/Return Air GrillesLouvered Stamped Supply Grille (CXB) X – – –
Double Deflection, Aluminum Finish Supply Grille – X (CXB X (CHY, CPY, CBY)
X (CHY, CPY, CBY)
Double Deflection, Integral Supply Grille - painted – X (CXB) – –Stamped Return Grille (CBY, CXB) X – – –
Hinged Bar-Type, Aluminum-finish Return Grille with Throwaway Filter - F.O. – – X (CHY, CPY, CBY)
X (CHY, CPY, CBY)
ControlsService Switch with Lockout Tabs – X – –Single Point Power Connection – X – –Incoming Power Fusing – X – –24 V Controls – X – –Condensate Overflow Switch – X – –3-Speed Switch X – X –Thermostats – – X –Custom Control (DDC) – X – X
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com28
Horizontal SeriesSTANdArd FEATurES & OPTIONS, Cont’d.
As detailed in the table on page 29, we offer a control
for most of the customer needs. Additional controls and
devices are available to meet even the most demanding
operating logic.
Three-speed Fan ControlAll of our basic control schemes utilize a 2- or 3-speed
switch to modulate the cooling output, to maximize the
percentage of latent heat removal, and to further minimize
the sound level when maximum cooling or heating
performance is not required.
Low Voltage Control (24 V)A low voltage control is available with all of our control
schemes.
Condensate High Level SwitchThis switch shuts down the unit when the water level in the
drain pan reaches an unsafe level. Building code changes in
much of the country now require this type of device.
Service SwitchesWe offer concealed service switches for use by maintenance
and service personnel to shut off the power while working
on the unit.
FusingWe offer incoming power fusing for all units as well as
blower motor and control sub-fusing for units that use
electric heat. The blower motor and control sub-fusing
(single power source wiring) is required when single source
power with electric heat is specified.
Control Packages
Horizontal Wall Series 155
Wall Series 4039 Vertical Wall Series 155
24 V Programmable and Non-Programmable
Digital Series
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
29
STANdArd FEATurES & OPTIONS, Cont’d.
Control Package Applications
Unit Type Control option System Type Changeover
TypeWall Series
4039
Vertical and Horizontal Wall
Series155
24 V Programmable and Non-Programmable
Digital Series– Manual Fan Manual1 None – – –
2-PipeValve Cycle*
Heat Only None
Cool Only None
Heat/CoolManual –
Automatic
Heat/Cool with Auxiliary Electric Heat
Manual –Automatic
Cool with Total Electric Heat
Manual –Automatic
4-Pipe Heat/CoolManual –
Automatic
NoTe: 1. Fan switch only; no thermostat.
Thermostat Features
All listed controls include fan switching.Control Type1
Wall Series 4039 Vertical and Horizontal Wall Series 155 24 V Digital Series
24 V, 115 V, 208 V, 240 V, 277 V 24 V onlyRemote Wall Mounted
Manual Fan Switch Operation
Auto Fan Speed Control N/A N/A
Continuous 3-Speed Fan
Cycling Fan N/A N/A
O.A. Damper Signal N/A
Remote Temperature Sensor N/A Opt OptAdjustable Operating Range Kit
Touch Pad/Digital Display N/A N/A
Local Temperature Set-Back N/A N/A
Water Temperature Purge Cycle N/A N/A
Pipe Sensor N/A N/A
NoTeS: 1. Control packages with valve cycle control are continuous fan operation only. 2. All wall-mount control packages are shipped loose for field installation. (Boxes, tile rings, plaster rings, etc. are not provided.) 3. Aquastats are included in control packages, as required.
Control Options• 24 V control packages• Unit-mounted fan switches (Special Quote)• Single power source wiring (motor/control fusing)• Incoming power fusing• Service switches
• Minimum room temperature thermostats (Special Quote)• Low voltage remote shutdown relays (Special Quote)• Fan and valve cycle applications (Special Quote)• Thermostats available with large letter print for handicap
applications (Special Quote)• DX coil applications
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com30
Horizontal SeriesSTANdArd FEATurES & OPTIONS, Cont’d.
Supply Air Grilles
Unit Size Nominal CFMRecommended
Grille Size - Inches (Millimeters)
02 200 16" x 6" (406 x 152)
03 300 20" x 6" (508 x 152)
04 400 26" x 6" (660 x 152)
06 600 30" x 6" (762 x 152)
08 800 38" x 6" (965 x 152)
10 1000 52" x 6" (1320 x 152)
12 1200 60" x 6" (1524 x 152)
NoTeS: 1. Refer to Physical Data, pages 13 through 26 for actual unit supply air opening dimensions.
2. Field-furnished duct transitions may be required.
Return Air Filter Grilles
Unit Size Nominal CFMRecommended
Grille Size - Inches (Millimeters)
02 200 24" x 10" (610 x 254)
03 300 28" x 10" (711 x 254)
04 400 32" x 10" (813 x 254)
06 600 42" x 10" (1067 x 254)
08 800 42" x 10" (1067 x 254)
10 1000 54" x 10" (1372 x 254)
12 1200 64" x 10" (1626 x 254)
NoTeS: 1. Refer to Physical Data, pages 13 through 26 for actual unit return air opening dimensions.
2. Field-furnished duct transitions may be required.
optional Double-deflection, Integral Supply Grille Painted to Match Color of Unit
optional Double Deflection, Aluminum-finish Supply Grille (optional special ship separate for models CHY, CPY, CBY, BHY,
and BPY. Consult factory for details.)optional Hinged, Bar-type, Aluminum-finish Return Grille
with Throwaway Filter (optional special ship separate for models CHY, CPY, CBY, BHY,
and BPY. Consult factory for details.)
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
31
STANdArd FEATurES & OPTIONS, Cont’d.
Nominal Filter SizesAll cabinet model units (except CH and BH) have non-woven synthetic throwaway filters furnished as standard equipment.
Cleanable and pleated filters are optional.
Unit Size
Nominal one-Inch Filter Size - Inches (Millimeters)
CHY (Note 1) CPY
CBY Bottom Return
Stamped
CBY Rear Return
Stamped
CXB Bottom Return
Stamped
CXB Rear Return
Stamped
CXB Rear Return
Ducted
02 10" x 24"(254 x 610)
10" x 18" (254 x 457)
10" x 28"(254 x 711)
7" x 21"(178 x 533)
10" x 23-1/2"(254 x 597)
8" x 23-1/2"(203 x 597)
8" x 23-1/2"(203 x 597)
03 10" x 28"(254 x 711)
10" x 22" (254 x 559)
10" x 28"(254 x 711)
7" x 21"(178 x 533)
10" x 28"(254 x 711)
8" x 28"(203 x 711)
8" x 28"(203 x 711)
04 10" x 32"(254 x 813)
10" x 28" (254 x 711)
10" x 33"(254 x 838)
7" x 27"(178 x 533)
10" x 32-1/2"(254 x 826)
8" x 32-1/2"(203 x 826)
8" x 32-1/2" (203 x 826)
06 10" x 42"(254 x 1067)
10" x 33" (254 x 838)
10" x 45"(254 x 1143)
7" x 38"(178 x 965)
10" x 37"(254 x 940)
8" x 37"(203 x 940)
8" x 37"(203 x 940)
08 10" x 42"(254 x 1067)
10" x 40" (254 x 1016)
10" x 45"(254 x 1626)
7" x 38"(178 x 965)
10" x 41"(254 x 1041)
8" x 41"(203 x 1041)
8" x 41"(203 x 1041)
10 10" x 54"(254 x 1372)
10" x 54" (254 x 1372)
10" x 62"(254 x 1575)
7" x 52"(178 x 1321)
10" x 54-1/2"(254 x 1384)
8" x 54-1/2"(203 x 1384)
8" x 54-1/2"(203 x 1384)
12 10" x 64" (254 x 1626)
10" x 62" (254 x 1575)
10" x 62"(254 x 1575)
7" x 52"(178 x 1321)
10" x 63"(254 x 1600)
8" x 63" (203 x 1600)
8" x 63"(203 x 1600)
Unit Size
Nominal one-Inch Filter Size - Inches (Millimeters)
BHY(Note 1)
BPYBottom Return
with Heat
BPYBottom Return without Heat
BPYRear Return
with Heat
BPY Bottom Return without Heat
04 10" x 32"(254 x 813)
16-3/4" x 28"(425 x 711)
12-3/4" x 28"(324 x 711)
12-3/4" x 28"(324 x 711)
12-3/4" x 28"(324 x 711)
06 10" x 42"(254 x 1067)
16-3/4" x 33"(425 x 838)
12-3/4" x 33"(324 x 838)
12-3/4" x 33"(324 x 838)
12-3/4" x 33"(324 x 838)
08 10" x 42"(254 x 1067)
16-3/4" x 40"(425 x 1016)
12-3/4" x 40"(324 x 1016)
12-3/4" x 40"(324 x 1016)
12-3/4" x 40"(324 x 1016)
10 10" x 54"(254 x 1372)
16-3/4" x 54"(425 x 1372)
12-3/4" x 54"(324 x 1372)
12-3/4" x 54"(324 x 1372)
12-3/4" x 54"(324 x 1372)
NoTeS: 1. Filter sizes for the CH and BH models are recommended filter sizes only. No filter is factory provided with these models. 2. Sizes shown are nominal ordering sizes.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com32
Horizontal SeriesPIPING PACKAGES (TyPICAL)
Two-way Motorized Control ValveIn a two-way motorized control valve package, the motor
drives the valve open, and a spring returns the valve to a
normally closed position. No water flows with the unit off.
The standard supply connection from the coil will accept
a swaged copper fitting for field brazing. As an option, this
connection may be factory furnished with a union. When a
swage is necessary, it becomes part of the valve package.
The isolation, or ball, valve in the return piping is shipped
loose for field installation.
(Ships Separate)
2-way ValveCoil
Air Vent
SwageS
R
S
R BallValve
BallValve
Two-way Motorized Control Valve with ChangeoverIn a two-way motorized changeover control valve package,
the motor drives the valve open, and a spring returns the
valve to a normally closed position. No water flows through
the coil with the unit off. The aquastat bypass line allows
a small amount of water to flow from the supply to the
return piping when the control valve is closed. The strap-
on aquastat senses whether the flowing water is cold or
hot and switches a contact closed to provide automatic
summer/winter changeover (ACO) for the system.
S
R
S
Swage
2-way ValveAquastat BleedBypass Line
A
Aquastat
R
Coil
Air Vent
Swage
BallValve
BallValve
Three-way Motorized Control ValveIn a three-way motorized control valve package, a diverting
valve controls water flow to the coil. When the unit is off,
water bypasses the coil and flows directly to the system
return. A balancing valve may be specified in the bypass line
to permit equal flow balancing.
OptionalBalance Valve
S
Swage
3-way Valve
R
Coil
Air Vent
SwageA
Aquastat
S
R BallValve
BallValve
NoTeS: 1. Please note that project specifications for system pressure, pressure drop limitations and flow rate should be checked prior to selecting specific components or the valve package size.
2. The supply and return piping connections of the factory-provided valve package are either swaged for field brazing (standard) or union fitted (optional) for connection to the coil.
3. Consult IEC’s Valve Packages and Piping Components manual or your local representative for detailed piping and valve application information. Factory-provided valve packages are assembled, brazed, wired electrically and dry-fit to the coil connections before shipping. Field brazing to the coil completes the installation. Some applications dictate shipping isolation valves loose.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
33
MECHANICAL SPECIFICATIONS
GENERAL DESCRIPTION – HORIZONTAL FAN COIL UNITSCHY – Horizontal Hideaway CBY – Horizontal Telescoping Hideaway CPY – Horizontal Hideaway with Plenum CXB – Horizontal Cabinet BHY – Horizontal Hi-Static Hideaway BPY – Horizontal Hi-Static Hideaway with Plenum
PART 11.1 SUMMARY
This section includes fan coil units and accessories.
1.2 SYSTEM DESCRIPTION
Horizontal Fan Coil Units, 2-pipe, 4-pipe, or 2-pipe with electric heat, concealed or exposed cabinets that are horizontally mounted.
1.3 QUALITY ASSURANCE
Coils shall be tested in accordance with AHRI Standard 440-2008. Each coil shall be factory tested for leakage at 300 psig air pressure with coil submerged in water. Insulation and adhesive shall meet NFPA-90A requirements for flame spread and smoke generation.
Base or “standard” units shall be ETL certified.
1.4 DELIVERY, STORAGE AND HANDLING
Unit shall be handled and stored in accordance with the manufacturer’s instructions.
PART 2 – PRODUCTS2.1 MANUFACTURER
A. Basis of design shall be fan coils by International Environment Corporation.
2.2 CONFIGURATION
A. General:
Factory assembled horizontal fan coil units complete with fan, motor, drain pan, and all required wiring, piping and controls.
B. CHY, BHY Horizontal Hideaway Units:
1. Cabinet shall be made of heavy gauge galvanized steel.
2. The interior surfaces shall be lined with 1/2" thick standard fiberglass (1/2" thick Premium IAQ fiberglass, 1/2" foil face, or 1/4" closed cell) insulation.
3. Units shall be supplied with a ducted collar for supply duct connection.
4. Units shall have a galvanized (or stainless steel) drain pan extending the entire width of the coil (with second drain con nection).
5. Galvanized drain pans shall be internally coated with 2-part closed cell foam insulation.
C. CPY, BPY Horizontal Hideaway with Plenum Units:
1. Units shall be constructed of heavy gauge galvanized steel.
2. The interior surfaces shall be lined with 1/2" thick standard fiberglass (1/2" thick Premium IAQ fiberglass, 1/2" foil face, or 1/4" closed cell) insulation.
3. A heavy gauge plenum shall enclose the blower/motor assembly with bottom or rear return.
4. Units shall be supplied with a ducted collar for supply duct connection.
5. Units shall have a galvanized (or stainless steel) drain pan extending the entire width of the coil (with second drain con nection).
6. Galvanized drain pans shall be internally coated with a 2-part closed cell foam insulation.
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com34
Horizontal SeriesMECHANICAL SPECIFICATIONS, Cont’d.
7. Units shall have non-woven synthetic throwaway (permanent or pleated) filters.
D. CXB Horizontal Cabinet Units:
1. Units shall be constructed of heavy gauge galvanized steel.
2. The interior surfaces shall be lined with 1/2" thick standard fiberglass (1/2" thick Premium IAQ fiberglass, 1/2" foil face, or 1/4" closed cell) insulation.
3. Cabinet shall be painted with an Arctic White powder-coat finish.
4. The unit shall have a stamped (double deflection, aluminum finish or steel construction factory installed and painted to match cabinet) discharge grille.
5. The unit shall have removable bottom access panel with stamped return air grille, filter rack, and non-woven synthetic throwaway (permanent or pleated) filter or optional ducted rear return cabinet with a solid bottom access panel.
6. Panel shall be fastened with tamper proof quarter-turn fasteners.
7. Units shall have a galvanized (or stainless steel) drain pan extending the entire width of the coil (with second drain con nection).
8. Galvanized drain pans shall be internally coated with a 2-part closed cell foam insulation.
E. CBY Horizontal Telescoping Hideaway Units:
1. Units shall be constructed of heavy gauge galvanized steel.
2. The interior surfaces shall be lined with 1/2" thick standard fiberglass (1/2" thick Premium
IAQ fiberglass, 1/2" foil face, or 1/4" closed cell) insulation.
3. Unit shall have an adjustable height, hinged return air ceiling panel with non-woven synthetic throwaway, (permanent, or pleated) filter.
4. Panel shall be painted with an Arctic White powder-coat finish.
5. Units shall have a galvanized (or stainless steel) drain pan extending the entire width of the coil (with second drain con nection).
6. Galvanized drain pans shall be externally coated with a 2-part closed cell foam insulation.
2.3 CERTIFICATION
A. Safety:
Units shall be listed by Electronics Testing Laboratories, Inc. with the ETL listing indicating the units comply with the minimum requirements of the U.S. and Canadian national product safety standard, UL 1995/CSA C22.2 No. 236.
B. Capacities:
Coil capacities are tested in accordance with AHRI Standard 440-2008.
2.3.1 MATERIALS
A. Coils:
All coils shall have 1/2" copper tubes, manual (or automatic) air vents, and aluminum fins, 10 fins per inch spacing. Coil fins shall be mechanically bonded to copper tubes. 0.500" O.D. copper tubes must comply with ASTM B-75. Fin thickness shall be 0.0045" and tube thickness shall be 0.016". All coils shall be leak tested with air at 300 psig under water.
1. For installation in a 2-pipe system, unit shall be equipped with:
a. 3-row (or 4-row) coil as shown on equipment drawings
b. 2 ball valves
c. 1 motorized control valve
International Environmental Corporation • Horizontal Series Fan Coil Technical Catalogwww.iec-okc.com
Horizontal Series
35
MECHANICAL SPECIFICATIONS, Cont’d.
2. For installation in a 4-pipe system, unit shall be equipped with:
a. 3/1, 3/2 or 4/1 row-split coil, as shown on equipment drawings
b. 4 ball valves
c. 2 motorized control valves
B. Fans:
1. Fans shall be direct-drive, double-width fan wheels with forward-curved blades.
2. Blower wheels shall be statically and dynamically balanced.
3. Scrolls and fan wheels shall be constructed of galvanized steel.
4. Shall be easily removable.
C. Fan Speed and Temperature Control:
3 (high, medium, low) speed control, (off, on, auto), (wall or unit) (auto or manual) thermostat.
D. Motors:
1. Motors shall be 3-speed, single phase, 60 Hz permanent split capacitor type for 115 V (208 V, 230 V, or 277 V) permanently lubricated, with sleeve bearings.
2. Motors shall be connected with quick connect electrical plugs.
3. Motors shall have thermal overload protection with automatic reset.
E. Controls and Safeties:
1. Controls:
Unit shall be furnished with a 3-speed, 4-position fan switch on a wall plate for field installation.
2. Safeties:
Unit fan motor shall be equipped with integral motor protection.
F. Operating Characteristics:
1. A 2-pipe system shall be capable of providing heating or cooling as determined by the operating mode of the central water supply system.
2. A 4-pipe system shall be capable of providing heating and cooling on demand.
G. Electrical Requirements:
1. Standard unit shall operate on 115 V (208 V, 230 V or 277 V), single phase, 60 Hz electrical power, and all exposed wiring shall be in flexible conduit.
H. Option and Accessories:
1. Unit shall be equipped with nichrome wire strip electric heaters for total or auxiliary electric heat as specified on the equipment schedule.
a. Heaters shall be protected by an automatic reset safety cutout switch and a fusible link.
b. Heater capacity shall be as specified on the equipment schedule.
c. Heaters shall be single phase, 120 V (208 V, 240 V or 277 V) volts as specified on the equipment schedule.
d. For total electric heat, unit controls shall include a sequenced heating and cooling thermostat in lieu of the heating/cooling thermostat and automatic changeover device.
e. For auxiliary electric heat, unit controls shall include an aquastat to verify system mode.
f. A junction box and fuse shall be factory furnished and installed to protect the motor and control circuit when electric heaters are installed.
2. Service switch shall be factory installed.
3. Units shall be equipped with 24 V controls.
4. Units shall be equipped with high level condensate switch.
5. A hinged, bar type aluminum return air grille with filter holder shall be furnished for field installation.
6. Discharge air grille with double deflection, aluminum construction shall be furnished for field installation as shown on equipment schedule. Aluminum grilles shall have a natural anodized finish.
IEC Catalog Part #: I100-90002102
CA-020 Revision 3
©2010 International Environmental Corporation (IEC)
IEC is a subsidiary of LSB Industries, Inc.
NYSE symbol LXU; www.lsb-okc.com
P.O. Box 2598Oklahoma City, OK 73101-2598
p: 405.605.5000f: 405.605.5001
www.iec-okc.com
The USGBC Member logo is a trademark owned by the U.S. Green Building Council and is used by permission. The logo signifies only that IEC is a USGBC member. USGBC does not review, certify, or endorse the products or services offered by its members.
IEC is dedicated to the environment and for its part, IEC has elected to use recycled materials whenever possible for printed sales materials.