International Communications in Heat and Mass...
Transcript of International Communications in Heat and Mass...
1
2
3Q1
4
5
678910111213141516
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
ICHMT-02872; No of Pages 7
Contents lists available at ScienceDirect
International Communications in Heat and Mass Transfer
j ourna l homepage: www.e lsev ie r .com/ locate / ichmt
F
Turbulent free convection in a porous square cavity using the thermalequilibirum model☆
Paulo H.S. Carvalho, Marcelo J.S. de Lemos ⁎Departamento de Energia — IEME, Instituto Tecnológico de Aeronáutica— ITA, 12228-900 São José dos Campos— SP, Brazil
O☆ Communicated by Dr. W.J. Minkowycz.⁎ Corresponding author.
E-mail address: [email protected] (M.J.S. de Lemos).
0735-1933/$ – see front matter © 2013 Published by Elsehttp://dx.doi.org/10.1016/j.icheatmasstransfer.2013.10.00
Please cite this article as: P.H.S. Carvalho, Mmodel, Int. Commun. Heat Mass Transf. (201
Oa b s t r a c t
a r t i c l e i n f o17
Available online xxxx 1819
20
21
22
Keywords:Turbulence modelingPorous mediaHeat transferNatural convection
23
24
25
26
27
D P
RThis work investigates the influence of porosity and thermal conductivity ratio on the Nusselt number of a cavityfiled with a fluid saturated porous substrate. The flow regime considered intra-pore turbulence and amacroscopic k-ε model was applied. Heat transfer across the cavity assumed the hypothesis of thermalequilibrium between the solid and the fluid phases. Transport equations were discretized using the control-volume method and the system of algebraic equations was relaxed via the SIMPLE algorithm. Results showedthat when using the one energy equation model under the turbulent regime, simulated with a High Reynoldsturbulence model, the cavity Nusselt number is reduced for higher values of the ratio ks/kf as well as when thematerial porosity is increased. In both cases, conduction thorough the solid material becomes of a greaterimportance when compared with the overall transport that includes both convection and conductionmechanisms across the medium.
© 2013 Published by Elsevier Ltd.
2829
E
T57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
UNCO
RREC
1. Introduction
Thermal convection in porous media and the parameters that affectheat transfer across a heterogeneous medium have been studiedextensively in recent years. There are several applications in industryfor this type of technology. Examples are studies on grain storage,optimization of solar collectors design, safety of nuclear reactors anddesign of porous burners for industrial furnaces, to mention a few.Traditionally, modeling of macroscopic transport for incompressibleflows in porous media has been based on the volume-average meth-odology [1–4]. Additionally, if the flow fluctuates in time, the literaturepresents a number of time- and volume-averaging techniques thatfollow distinct sequences when applying both averaging operators[5–11]. Recently, a concept named double decomposition [12] showedthat the sets of macroscopic mass transport equations are equivalent,regardless of the order of application of the averaging operators.
When buoyancy forces are of concern, natural convection occurs inenclosures as a result of gradients in densities which, in turn, are dueto variations in temperature or mass concentration within themedium.
For clear cavities, the first turbulence model introduced forcalculating buoyant flows was proposed by Markatos and Pericleous[13]. They performed steady 2-D simulations for Ra up to 1016 andpresented a complete set of results. Ozoe et al. [14], in the light of thesame model adopted by [13], applied it to 2D calculations up to Ra=1011. Henkes et al. [15] compared two different turbulence models for2D calculations, namely the standard High Reynolds k-ε closure as
83
84
85
86
vier Ltd.3
.J.S. de Lemos, Turbulent free3), http://dx.doi.org/10.1016
well as the Low–Reynolds number form of the model. Further, Fusegiet al. [16] presented 3D calculations for laminar flow for Ra up to 1010
in a cube. The results revealed that the behaviors of the flow andcomparisons were made with 2D simulations. The differences werereported considering heat transfer correlation between Nu and Ra for2D and 3D cases. Later, Barakos et al. [17] also studied the problem ofnatural convection flow in a clean square cavity. The k-ε model hasbeen used for modeling turbulence with and without wall functions.
For cavities fitted with a porous material, the problem of freeconvection in enclosures with distinct temperatures applied on eachside of the cavity has been shown to represent a number of engineeringsystems of practical relevance. The monographs of Nield and Bejan [18]and Ingham and Pop [19] fully document natural convection in porousmedia. In addition, several articles published in the literature madeimportant contributions to the understanding of this problem [20–26].Baytas and Pop [27] considered a numerical study of steady freeconvection flow in rectangular and oblique cavities, filled with homo-geneous porous media using a nonlinear axis transformation. TheDarcy momentum and energy equations were numerically solvedusing the (ADI) method.
In the work of Braga and de Lemos (2004) [28], an approximatecritical Rayleigh was proposed comparing the behavior of Laminar andHigh Reynolds turbulence model solutions. The geometry thereinvestigated was a square cavity totally filled with a porous material,which was heated from the left and cooled from the opposing side.Also worth to mention is that the work in [28] was based on the localthermal equilibrium (LTE) hypothesis, which considers one uniquetemperature for both the fluid and the solid porous material. Othercases not involving gravity driven motion [29] have also been analyzedwith the laminar version of the LTE model detailed in [12]. Further, in
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003
UNCO
RRECT
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
T1:1 Nomenclature
T1:2 Latin charactersT1:3 cF Forchheimer coefficientT1:4 c′s Non-dimensional turbulence model constantsT1:5 cp Specific heatT1:6 D Deformation rate tensor, D=[∇u+(∇u)T]/2T1:7 Da Darcy number, Da ¼ K
H2
T1:8 D Particle diameter, DT1:9 g Gravity acceleration vectorT1:10 Gi Generation rate of ⟨k⟩i due to the action of the porousT1:11 matrixT1:12 Gβ
i Generation rate of ⟨k⟩i due to buoyant effectsT1:13 h Heat transfer coefficientT1:14 H Cavity heightT1:15 I Unit tensorT1:16 K Permeability, K ¼ D2ϕ3
144 1−ϕð Þ2T1:17 k Turbulent kinetic energy per unit mass, k ¼ u′ � u′=2T1:18 kf Fluid thermal conductivityT1:19 ks Solid thermal conductivityT1:20 Kdisp Conductivity tensor due to thermal dispersionT1:21 Kdisp,t Conductivity tensor due to turbulent thermal dispersionT1:22 Kt Conductivity tensor due to turbulent heat fluxT1:23 Ktor Conductivity tensor due to tortuosityT1:24 L Cavity widthT1:25 Nu Nusselt number, Nu ¼ hL
�keff
T1:26 Pi Production rate of ⟨k⟩i due to gradients of uD
T1:27 Pr Prandtl numberT1:28 Raf Macroscopic Fluid Rayleigh number, Raf ¼ gβϕH
3ΔTv f αeff
T1:29 Ram Darcy–Rayleigh number, Ram=Raf ⋅Da= gβϕHΔTKν f αeff
T1:30 Racr Critical Rayleigh numberT1:31 ReD Reynolds number based on the particle diameter, ReD ¼T1:32 ρ uDj jD
μ f
T1:33 T TemperatureT1:34 u Microscopic velocityT1:35 uD Darcy or superficial velocity (volume average of u)T1:36T1:37 Greek charactersT1:38 α Thermal diffusivityT1:39 β Thermal expansion coefficientT1:40 ΔV Representative elementary volumeT1:41 ΔVf Fluid volume inside ΔVT1:42 ε ε ¼ μ∇u′ : ∇u′ð ÞT=ρ, Dissipation rate of kT1:43 μ Dynamic viscosityT1:44 μt Microscopic turbulent viscosityT1:45 μtϕ Macroscopic turbulent viscosityT1:46 ν Kinematic viscosityT1:47 ρ DensityT1:48 σ′s Non-dimensional constantsT1:49 ϕ ϕ ¼ ΔV f
�ΔV , Porosity
T1:50T1:51 Special charactersT1:52 φ General variableT1:53 φ Time averageT1:54 φ′ Time fluctuationT1:55 ⟨φ⟩i Intrinsic averageT1:56 ⟨φ⟩v Volume averageT1:57
iφ Spatial deviationT1:58 |φ| Absolute value (Abs)T1:59 φ General vector variableT1:60 φeff Effective value of φ, φeff=ϕφf+(1−ϕ)φs
T1:61 φs,f solid/fluidT1:62 φH,C Hot/coldT1:63 φϕ Macroscopic valueT1:64 ()T TransposeT1:65
2 P.H.S. Carvalho, M.J.S. de Lemos / International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
Please cite this article as: P.H.S. Carvalho, M.J.S. de Lemos, Turbulent freemodel, Int. Commun. Heat Mass Transf. (2013), http://dx.doi.org/10.1016
OO
F
[28] it was also shown that lowDarcynumbers impact in higher averageNusselt numbers at the hot wall. However, in reference [28] simulationswere limited to a single solid-to-fluid thermal conductivity ratio,ks/kf=1, and a single porosity value, ϕ=0.8.
Motivated by the foregoing work, the contribution of this work is toextend the findings in [28] varying now the ratio ks/kf and the porosityφ. The turbulence model here adopted is the macroscopic k-ε withwall function in addition to the Low Reynolds number version of themodel. The findings herein broaden the simulations presented earlierin [28] since a greater number of heterogonous systems are nowinvestigated, leading to the analysis and optimization of a wider rangeof practical engineering systems.
2. The problem under consideration
The problem considered is showed schematically in Fig. 1a andrefers to a square cavity with sides L=H=1m completely filled witha porous medium. The cavity is isothermally heated from the left, TH,and cooled from the opposing side, TC. The other twowalls are thermallyinsulated. These boundary conditions are widely applied when solvingbuoyancy-driven cavity flows. The porous medium is considered to berigid and saturated by an incompressible fluid. The modified Rayleighnumber, Ram, is a dimensionless parameter used in porous media
ED P
RTH TC
dT/dy=0
dT/dy=0g
yx
H
L
a
b
Fig. 1. a) Geometry under consideration; b) 80 × 80 stretched grid.
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003
T
108
109
110
111
112
113
114
115
116
117
118119120
121122123
124125126
127128129130131132133
134
135
136
137
138
139
140
141142
143144145
146147148149
150
151
152
153154
155156157158159
t1:1
t1:2
t1:3
t1:4
t1:5
t1:6
t1:7
t1:8
t1:9
Table 2 t2:1
t2:2Comparison of laminar results for average Nusselt at hot wall, Nu Nuw , with Ram varyingt2:3from 10 until 104, Da=10−7, ϕ=0.8 and ks/kf=1.
t2:4Ram
t2:510 102 103 104
t2:6Walker and Homsy [20] – 3.097 12.96 51.0t2:7Bejan [21] – 4.2 15.8 50.8t2:8Beckermann et al. [23] – 3.113 – 48.9t2:9Gross et al. [24] – 3.141 13.448 42.583t2:10Manole and Lage [25] – 3.118 13.637 48.117t2:11Moya et al. [26] 1.065 2.801 – –
t2:12Baytas and Pop [27] 1.079 3.16 14.06 48.33t2:13Braga and de Lemos [28] 1.090 3.086 12.931 38.971t2:14Present results 1.087 3.093 13.041 39.288
3P.H.S. Carvalho, M.J.S. de Lemos / International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
CO
RREC
analysis and it is defined as Ram = RafDa, where Da = K/H2, αeff ¼keff�
ρ cpð Þ f . D is the particle diameter used to calculate the permeability,
K, and is here given by D ¼ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi144K 1−φð Þ2
φ3
r.
3. Governing equations
For turbulent buoyant flows, macroscopic governing equations areobtained by taking both volumetric and time averaging of the entireequation set. The final forms of the equations considered here aregiven in detail in [12] and for this reason their derivation need not berepeated. They read:
Continuity:
∇ � uD ¼ 0 ð1Þ
Momentum:
ρ∂uD
∂t þ∇ � uDuD
ϕ
� �� �¼ −∇ ϕ ph ii
� þ μ∇2uD þ∇ � −ρϕ u′u′
D Ei� �
−ρβϕgϕ T �i−Tref
� − μφ
KuD þ cFϕρ juDjuDffiffiffiffi
Kp
� �ð2Þ
Turbulent kinetic energy:
ρ∂∂t ϕ kh ii�
þ∇ � uD kh ii� � �
¼ ∇ � μ þμtϕ
σk
� �∇ ϕ kh ii� � �
þ Pi þ Gi
þ Giβ−ρϕ εh ii ð3Þ
Dissipation rate of turbulence kinetic energy:
ρ∂∂t ϕ εh ii�
þ∇ � uD εh ii� � �
¼ ∇ � μ þμ tϕ
σε
� �∇ ϕ εh ii� � �
þ c1Pi εh iikh ii
þc2εh iikh ii G
i þ c1c3Giβ
εh iikh ii −c2 f 2ρϕ
εh ii2kh iið4Þ
where the Dupuit–Forchheimer relationship,uD ¼ φ uh ii, has been usedand uh ii identifies the intrinsic (liquid) average of the local velocityvector u, ⟨k⟩i is the intrinsic average for k, ⟨ε⟩i is the intrinsic dissipationrate of k, K is the medium permeability, Gi ¼ ckρϕ kh ii juDj=
ffiffiffiffiK
pis the
generation rate of ⟨k⟩i due to the action of the porous matrix, Giβ ¼ φ
μtϕσ t
βkϕg �∇ T
�i is the generation rate of ⟨k⟩i due to buoyant effects, βϕ ¼ρβ T−Trefð Þh ivρϕ Th ii−Trefð Þ is the macroscopic thermal expansion coefficient and βk
ϕ ¼β u0T ′ �vϕ u0T ′
f
�i is the macroscopic thermal coefficient appearing in the Gβi
term. Here, for simplicity, we assume βϕk =βϕ=β (see [12] for details).
Further, Pi ¼ −ρ u′u′D Ei
: ∇uD is the production rate of ⟨k⟩i due to
UN
160161
Table 1Damping functions and constants for High and Low Reynolds turbulence models.
High Reynolds modelproposed by Launderand Spalding [30]
Low Reynolds model proposed by Abe et al. [31]
fμ 1.01− exp − νεð Þ0:25y
14ν
h in o21þ 5
k2=νεð Þ0:75 exp − k2=νεð Þ200
� �2" #( )
f2 1.01− exp − νεð Þ0:25y
3:1ν
h in o21−0:3 exp − k2=νεð Þ
6:5
� �2" #( )
σk 1.0 1.4σε 1.33 1.3c1 1.44 1.5c2 1.92 1.9
Please cite this article as: P.H.S. Carvalho, M.J.S. de Lemos, Turbulent freemodel, Int. Commun. Heat Mass Transf. (2013), http://dx.doi.org/10.1016
ED P
RO
OFgradients of uD , the c's are constants and f2 is a damping function to
be commented upon later. The term −ρϕ u′u′D Ei
is known as themacroscopic Reynolds stress tensor (MRST) and is given by:
−ρϕ u′u′D Ei ¼ μtϕ
2 D �v−2
3ϕρ kh iiI ð5Þ
where
D �v ¼ 1
2∇ ϕ uh ii�
þ ∇ ϕ uh ii� h iTh i
ð6Þ
is the macroscopic deformation rate tensor. The macroscopic turbulentviscosity μ tϕ
is modeled as,
μ tϕ¼ ρ cμ f μ
kh ii2εh ii ð7Þ
where cμ is a constant and fμ is another damping function to bepresented below.
In a similar way, applying both time and volumetric average to themicroscopic energy equation and invoking the Local Thermal EquilibriumHypothesis, which considers as mentioned T f
�i ¼ Ts �i ¼ T
�i, a
modeled form for the macroscopic energy equation reads (see [12]),
ρcp�
fϕþ ρcp
� s1−ϕð Þ
� ∂ T �i∂t þ ρcp
� f∇ � uD T
�i� ¼ ∇ � Keff �∇ T
�in oð8Þ
where, Keff, given by:
Keff ¼ ϕkf þ 1−ϕð Þksh i
Iþ Ktor þ Kt þ Kdisp þ Kdisp;t ð9Þ
is the effective conductivity tensor. In order to be able to apply Eq. (8), it isnecessary to determine the conductivity tensors in Eq. (9), i.e. Ktor, Kt, Kdisp
and Kdisp,t. The turbulent heat flux and turbulent thermal dispersionterms, Kt and Kdisp,t are modeled such that,
−ϕ ρcp�
fu′ T ′
f
D Ei ¼ ϕ ρcp�
f
νtϕ
Prt∇ T f
D Ei ¼ Kt þ Kdisp;t
� �∇ T f
D Eið10Þ
Table 3 t3:1
t3:2Effect of simulation model on average Nusselt at hot wall, Nu Nuw , with Da=10−7, ϕ=t3:30.8, and ks/kf=1.
t3:4Ram
t3:5103 104 105 106
t3:6Braga and de Lemos [28] (HR) 13.032 40.614 101.647 237.546t3:7High Re turbulence model 13.271 41.792 101.503 234.930t3:8Low Re turbulence model, yW+=0.767 13.132 40.602 96.918 –
t3:9Laminar model 13.041 39.288 88.238 172.491
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003
162163
164165166
167
168
169
170
171
172
173
174175
176
4 P.H.S. Carvalho, M.J.S. de Lemos / International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
where the symbolνtϕexpresses themacroscopic kinematic eddy viscosity
such that μtϕ¼ ρ f νtϕ
and Prt is a constant known as turbulent Prandtlnumber, which is often represented in the literature by σt. A furthersimplification is that, under the conditions here studied, Ktor and Kdisp
are negligible when compared to Kt Kt and Kdisp [28].
177178
179180181182183
184
185
186
3.1. Wall treatment and boundary conditions
In this work, two forms of the k-ε model are employed, namely theHigh Reynolds (Launder and Spalding [30]) and Low Reynolds number(Abe et al. [31]) turbulence models. The constants and formulae usedas damping functions are shown in Table 1. Boundary conditions aregiven by:
On the solid walls (Low Reynolds turbulence model):
u ¼ 0; k ¼ 0; ε ¼ ν∂2k∂y2
ð11Þ
UNCO
RRECT
a
b
Fig. 2. Average Nusselt at hot wallNuw forϕ=0.8,D=1.06×10−3m,Da=10−7 and 80×80 stturbulence model, varying ks/kf.
Please cite this article as: P.H.S. Carvalho, M.J.S. de Lemos, Turbulent freemodel, Int. Commun. Heat Mass Transf. (2013), http://dx.doi.org/10.1016
OF
On the solid walls (High Reynolds turbulence model):
uuτ
¼ 1κ
ln yþE�
; k ¼ u2τ
c1=2μ
; ε ¼ c3=4μ k3=2w
κyw; qw ¼
ρcp�
fc1=4μ k1=2w T−Tw
� �Prtκ
ln yþw�
þ cQ Prð Þ� �
ð12Þ
with, uτ ¼ τwρ
� 1=2; yþw ¼ ywuτ
ν ; cQ ¼ 12:5Pr2=3 þ 2:12 ln Prð Þ−5:3 forPrN0:5 where, Pr and Prt are, as mentioned, the Prandtl and turbulentPrandtl numbers, respectively, qw is the wall heat flux, uτ is the wall-friction velocity, yw is the non-dimensional coordinate normal to wall,K is the von Kármán constant, and E is a constant that depends on theroughness of the wall.
4. Numerical method and solution procedure
The numerical method employed for discretizing the governingequations is the control-volume approach. Hybrid schemes, upwind
ED P
RO
retched grid: a) Laminar andHigh Reynolds turbulencemodels, ks/kf=1, b) High Reynolds
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207208
209210
5P.H.S. Carvalho, M.J.S. de Lemos / International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
differencing scheme (UDS) and central differencing scheme (CDS), areused for interpolating the convection fluxes. The well-establishedSIMPLE algorithm [32] is applied for handling the pressure–velocitycoupling. Algebraic equation sets for each variable were solved by theSIP procedure of [33]. In addition, the concentration of nodal pointsclose to the walls aims at capturing the boundary layers close to thesolid surfaces.
5. Results and discussion
To guarantee a grid independent solution, runs were performed usingstretched grids with 60 × 60, 80 × 80, 100 × 100 control volumes andRam=105. In these three cases, the average Nusselt number at the hotwall showed that the grid 80 × 80 is refined enough to capture theboundary layers at vertical surfaces, since the difference in the resultswas less than 2% when compared with similar simulations obtained
UNCO
RRECT
a
b
Fig. 3. Effects of porosity on average Nusselt at hot wall, Nuw, using the HR turbu
Please cite this article as: P.H.S. Carvalho, M.J.S. de Lemos, Turbulent freemodel, Int. Commun. Heat Mass Transf. (2013), http://dx.doi.org/10.1016
F
with a finer grid. For example, for Ram=105 and for a grid with 80×80nodes (Fig. 1b), the average Nusselt at hot wall was calculated as101.503, whereas for a mesh of size 100×100, the computed value was103.38. As such, a grid of size 80×80was chosen for all simulations herein.
Further, the local Nusselt number on the hot wall for the squarecavity at x=0 is defined as,
Nu ¼ hL=keff∴Nu ¼ qWkeff
!x¼0
LTH−TC
ð13Þ
and the average Nusselt number is given by,
Nuw ¼ 1H
ZH0
Nudy: ð14Þ
ED P
RO
O
lent model, D=1.06× 10−3m and varying Ram: a) ks/kf=1, b) ks/kf=10.
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233Q2
234
235
236
237
238
239
240
6 P.H.S. Carvalho, M.J.S. de Lemos / International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
6. Laminar model solution
In order to calibrate the solution, runs were performed using thestretched grid shown in Fig. 1b. Results are presented shown inTable 2 and compared with the literature for φ=0.8 and Da=10−7.In all results, the Prandtl Number, thermal conductivity ratio betweensolid and fluid phases, fluid density and specific heat considered weretaken as unity. As one can see in Table 2, the present results agreewell with those reported in the literature.
7. Turbulent model solution
7.1. High Reynolds turbulence model
As Braga and de Lemos [28] pointed out, it is important to emphasizethat the main objective of this work is not to simulate the transitionmechanism from laminar regime to fully turbulent flow, but ratheridentify the ranges of validity of each model. Here, a 80×80 stretched
UNCO
RRECT
a
b
Fig. 4. Overall heat flux along hot wall using the HR turbulent model, D=
Please cite this article as: P.H.S. Carvalho, M.J.S. de Lemos, Turbulent freemodel, Int. Commun. Heat Mass Transf. (2013), http://dx.doi.org/10.1016
F
grid has been used and the results are compared with those in [28] inTable 3 for Ram ranging from 10 to 106. Table 3 also presents resultsusing the Laminar model. As can be seen in Table 3 and Fig. 2a, thecritical Rayleigh number, Racr, is assumed to be the value when thetwo solutions deviate from each other. Here, the computed Racr alsoagrees with that proposed in Braga and de Lemos [28] as Racr = 104
for ks/kf=1.
7.2. Low Reynolds turbulence model
It is known that Low Reynolds turbulence models make use ofdamping functions and require that the first grid node close to thewall corresponds to a non-dimensional wall distance of about yw+≈ 1.Going back to Table 3, one can note that for Ram up to 104, calculatedNusselt are similar, regardless of the model used, namely HR, LR orLaminar models. After such value, here considered as a critical value,Racr, the role of the model used becomes important when obtainingNuw.
ED P
RO
O
1.06 × 10−3m, Ram=105 and varying ϕ: a) ks/kf=1, b) ks/kf=10.
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003
T
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257Q3
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308309310311312313314315316317318319320321322323324325326327328329330331332333334335336337338339340341342343344345346347348349350351352353354355356357358359360361362363364365366367368369370371372373374375376377378379380
381
7P.H.S. Carvalho, M.J.S. de Lemos / International Communications in Heat and Mass Transfer xxx (2013) xxx–xxx
UNCO
RREC
8. Effect of thermal conductivity ratio ks/kf
The ratio between the solid and fluid thermal conductivity plays animportant role in the study of energy transport across saturated porousmedia. To the best of the authors' knowledge, in all published materialsthe ratio ks/kf has been set to unit. However, for real engineeringproblems, such ratio may attain higher values and, for that, a study forobtaining Nu Nuw with a varying ratio ks/kf is here included.
Fig. 2b shows values for Nuw when ks/kf is varied from 1 to 20 fora range for Ram covering 10 to 106 and using the High Reynoldsturbulence model. As the ks/kf increases, the average Nusselt decreases.As conduction mechanism through the solid material becomes of ahigher importance, the relative contribution of the transport due toconvective currents is reduced, leading to reduction on the numericalvalue Nuw. In the limiting case, when ks/kf → ∞, the cavity Nusseltnumber would tend to attain unity reflecting the fact that conductionheat transfer, in such limiting case, would be the dominant mechanismof heat transport across the cavity.
9. Effect of porosity φ
Porosity is another important parameter to be consideredwhen heattransport across the cavity is investigated. For a cavity as in Fig. 1a, Nuwrepresents the ratio between the sum of convection and conductiontransport mechanisms over conduction transport alone. Therefore, fora purely conductive heat transfer process across the cavity, Nuw wouldattain the unity valid, as defined by Eqs. (13) and (14).
Fig. 3a indicates that as porosity decreases, Nuw increases anddifferences became higher for higher values of Ram. All runs in Fig. 3were performed using the High Reynolds turbulence model, the80×80 stretched grid in Fig. 1b and ks/kf=1. The same effect also occursfor ks/kf=10(Fig. 3b). One explanation for this behavior is that althoughthe convective effects increase as the porosity increases, on the overall,including the conduction through the solid, the total heat transfer acrossthe cavity is reduced, which, in turn, reduces Nuw (see the definition ofNuw by inspecting Eqs. (13) and (14)). Also, for the same value for Ram,comparing Fig. 3a and b shows that Nuw is reduced as ks/kf increases, aresult that is coherent with those shown in Fig. 2b where, for a largersolid-to-fluid thermal conductivity ratio, the relative importance ofconvective heat transport across the cavity is reduced, reducing thenNuw.
Finally, Fig. 4 shows that indeed a higher porosity implies a loweroverall wall heat flux qw along the hot wall at x=0, which, in light ofthe definition of Nuw by Eqs. (13) and (14), explains why the Nusseltnumber is reduced when ϕ increases. In spite of having more voidspace for the fluid to flow, the enhancement of the overall heattransport across the cavity does not occur as ϕ increases.
The reduction of Nuw when ϕ increases can be better understood byinspecting again Fig. 4a that is plotted for ks/kf = 1. In this case, theeffective conductivity, which is given by keff = ϕ kf + (1 − ϕ)ks orkeff=kf[ϕ+(1−ϕ)(ks/kf)], will always give keff/kf for ks/kf=1 regardlessof the value ofϕ. Therefore, the reduction on qw asϕ increases implies ina reduction of Nuw by means of its definition (Eqs. (13) and (14)). Asimilar reasoning applies when examining Fig. 4b for ks/kf=10.
10. Conclusion
Computations for laminar and turbulent flowswith themacroscopick-ε model with wall function for natural convection in a square cavityfully filled with porous medium were performed. Results indicate thatwhen using the one energy equationmodel under the turbulent regimesimulated with a High Reynolds turbulence model, the cavity Nusseltnumber is reduced for higher values of the ratio ks/kf as well as whenthe material porosity in increased. In both cases, conduction thoroughthe solid material becomes of a greater importance when comparedwith the overall transport that includes also convective heat transport
Please cite this article as: P.H.S. Carvalho, M.J.S. de Lemos, Turbulent freemodel, Int. Commun. Heat Mass Transf. (2013), http://dx.doi.org/10.1016
ED P
RO
OF
due to fluid motion. The work herein might benefit the solution ofindustrial problems of practical relevance.
Acknowledgments
The authors are thankful to CNPq and CAPES, Brazil, for theirinvaluable financial support during the course of this research.
References
[1] C.T. Hsu, P. Cheng, Thermal dispersion in a porousmedium, Int. J. Heat Mass Transfer33 (1990) 1587–1597.
[2] J. Bear, Dynamics of Fluids in PorousMedia, AmericanElsevier Pub. Co., NewYork, 1972.[3] S. Whitaker, Equations of motion in porous media, Chem. Eng. Sci. 21 (1966) 291.[4] S. Whitaker, Diffusion and dispersion in porous media, J. Am. Inst. Chem. Eng. 13 (3)
(1967) 420.[5] T. Masuoka, Y. Takatsu, Turbulencemodel for flow through porousmedia, Int. J. Heat
Mass Transfer 39 (13) (1996) 2803–2809.[6] F. Kuwahara, A. Nakayama, H. Koyama, A numerical study of thermal dispersion in
porous media, J. Heat Transf. 118 (1996) 756–761.[7] F. Kuwahara, A. Nakayama, Numerical modeling of non-Darcy convective flow in a
porous medium, Heat Transfer 1998: Proc. 11th Int. Heat Transf. Conf., Kyongyu,Korea4, Taylor & Francis, Washington, D.C., 1998, pp. 411–416.
[8] A. Nakayama, F. Kuwahara, A macroscopic turbulence model for flow in a porousmedium, J. Fluids Eng. 121 (1999) 427–433.
[9] K. Lee, J.R. Howell, Forced convective and radiative transfer within a highly porouslayer exposed to a turbulent external flow field, Proceedings of the 1987ASME-JSME Thermal Engineering Joint Conf., Honolulu, Hawaii2, ASME, New York,N.Y., 1987, pp. 377–386.
[10] B.V. Antohe, J.L. Lage, A general two-equation macroscopic turbulence model forincompressible flow in porous media, Int. J. Heat Mass Transfer 40 (13) (1997)3013–3024.
[11] D. Getachewa, W.J. Minkowycz, J.L. Lage, Int. J. Heat Mass Transfer 43 (2000) 2909.[12] M.J.S. de Lemos, Turbulence in Porous Media: Modeling and Applications, 2nd ed.
Elsevier, Amsterdam, 2012.[13] N.C. Markatos, K.A. Pericleous, Laminar and turbulent natural convection in an
enclosed cavity, Int. J. Heat Mass Transfer 27 (1984) 755–772.[14] H. Ozoe, A. Mouri, M. Ohmuro, S.W. Churchill, N. Lior, Numerical calculations of
laminar and turbulent natural convection in water in rectangular channels heatedand cooled isothermally on the opposing vertical walls, Int. J. Heat Mass Transfer28 (1985) 125–138.
[15] R.A.W.M. Henkes, F.F. Van Der Vlugt, C.J. Hoogendoorn, Natural-convection flow in asquare cavity calculated with low-Reynolds-number turbulence models, Int. J. HeatMass transfer 34 (2) (1991) 377–388.
[16] T. Fusegi, J.M. Hyun, K. Kuwahara, Three-dimensional simulations of naturalconvection in a sidewall-heated cube, Int. J. Numer.Methods Fluids 3 (1991) 857–867.
[17] G. Barakos, E. Mitsoulis, D. Assimacopoulos, Natural convection flow in a squarecavity revited: laminar and turbulent models with wall function, Int. J. Numer.Methods Fluids 18 (1994) 695–719.
[18] D.A. Nield, A. Bejan, Convection in Porous Media, Springer, New York, 1992.[19] D.B. Ingham, I. Pop, Transport Phenomena in PorousMedia, Elsevier, Amsterdam, 1998.[20] K.L. Walker, G.M. Homsy, Convection in Porous Cavity, J. Fluid Mech. 87 (1978)
49–474.[21] A. Bejan, On the boundary layer regime in a vertical enclosure filled with a porous
medium, Lett. Heat Mass transfer 6 (1979) 93–102.[22] V. Prasad, F.A. Kulacki, Convective heat transfer in a rectangular porous cavity-effect of
aspect ratio on flow structure and heat transfer, J. Heat Transfer 106 (1984) 158–165.[23] C. Beckermann, R. Viskanta, S. Ramadhyani, A numerical study of non-Darcian
natural convection in a vertical enclosure filled with a porous medium, Numer.Heat Transfer 10 (1986) 557–570.
[24] R.J. Gross, M.R. Bear, C.E. Hickox, The Application of Flux-corrected Transport (FCT)to High Rayleigh Number Natural Convection in a Porous Medium, Proc, 8th Int.Heat transfer Conf., San Francisco, CA, 1986, 1986.
[25] D.M. Manole, J.L. Lage, Numerical benchmark results for natural convection in aporous medium cavity, HTD-Vol 216, Heat and mass Transfer in Porous Media,ASME Conference, 1992. 55–60.
[26] S.L. Moya, E. Ramos, M. Sen, Numerical study of natural convection in a tiltedrectangular porous material, Int. J. Heat Mass Transfer 30 (1987) 741–756.
[27] A.C. Baytas, I. Pop, Free convection in oblique enclosures filled with a porousmedium, Int. J. Heat Mass Transfer 42 (1999) 1047–1057.
[28] E.J. Braga, M.J.S. de Lemos, Turbulent natural convection in a porous square cavitycomputedwith amacroscopic k-εmodel, Int. J. HeatMass Transf. 47 (2004) 3650–5639.
[29] M.J.S. de Lemos, C. Fischer, Thermal analysis of an impinging jet on a plate with andwithout a porous layer, Numer. Heat Transfer, Part A 54 (2008) 1022–1041.
[30] B.E. Launder, D.B. Spalding, The numerical computation of turbulent flows, Comput.Methods Appl. Mech. Eng. 3 (1974) 269–289.
[31] K. Abe, Y. Nagano, T. Kondoh, An improve k-ε model for prediction of turbulentflows with separation and reattachment, Trans. JSME 58 (1992) 3003–3010.
[32] S.V. Patankar, D.B. Spalding, A calculation procedure for heat, mass and momentumtransfer in three dimensional parabolic flows, Int. J. Heat Mass Transfer 15 (1972)1787.
[33] H.L. Stone, Iterative solution of implicit approximations of multi-dimensional partialdifferential equations, SIAM J. Numer. Anal. 5 (1968) 530–558.
convection in a porous square cavity using the thermal equilibirum/j.icheatmasstransfer.2013.10.003