Integrated Services Digital Network (ISDN); Signalling System … · Final draft ETSI EN 300...

Final draft ETSI EN 300 899-3 V1.1.1 (2001-07)

European Standard (Telecommunications series)

Integrated Services Digital Network (ISDN);Signalling System No.7;

Interworking between ISDN User Part (ISUP) version 2and Digital Subscriber Signalling System No. one (DSS1);

Part 3: Test Suite Structure andTest Purposes (TSS&TP) specification

ETSI

Final draft ETSI EN 300 899-3 V1.1.1 (2001-07)2

ReferenceDEN/SPAN-130052-3

KeywordsDSS1, interworking, ISDN, ISUP, SS7, TSS&TP

ETSI

650 Route des LuciolesF-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 CAssociation à but non lucratif enregistrée à laSous-Préfecture de Grasse (06) N° 7803/88

Important notice

Individual copies of the present document can be downloaded from:http://www.etsi.org

The present document may be made available in more than one electronic version or in print. In any case of existing orperceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).

In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drivewithin ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.Information on the current status of this and other ETSI documents is available at http://www.etsi.org/tb/status/

If you find errors in the present document, send your comment to:[email protected]

Copyright Notification

No part may be reproduced except as authorized by written permission.The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2001.All rights reserved.

http://www.etsi.org/

http://www.etsi.org/tb/status

[email protected]

ETSI


Contents

Intellectual Property Rights ..........................................................................................................................7

Foreword......................................................................................................................................................7

1 Scope..................................................................................................................................................8

2 References ..........................................................................................................................................8

3 Definitions and abbreviations............................................................................................................113.1 Definitions ................................................................................................................................................ 113.2 Abbreviations............................................................................................................................................ 12

4 Implementation under test and test methods ......................................................................................134.1 Identification of the system and implementation under test......................................................................... 134.2 ATM and testing configuration .................................................................................................................. 134.2.1 Test method ......................................................................................................................................... 134.3 Untreatable test purposes ........................................................................................................................... 15

5 Test Suite Structure (TSS) ................................................................................................................155.1 Interworking from DSS1 to ISUP (outgoing call) ....................................................................................... 155.2 Interworking from Non-ISDN access to ISUP (outgoing call)..................................................................... 155.3 Interworking from ISUP to DSS1 (incoming call) ...................................................................................... 165.4 Interworking from ISUP to Non-ISDN access (incoming call).................................................................... 165.5 Supplementary Services - Interworking from DSS1 to ISUP (outgoing call) ............................................... 175.6 Supplementary Services - Interworking from ISUP to DSS1 (incoming call) .............................................. 17

6 Test purposes (TP)............................................................................................................................186.1 Introduction............................................................................................................................................... 186.1.1 Test purpose (TP) naming convention .................................................................................................. 186.1.2 Source of test purpose definition .......................................................................................................... 186.1.3 Test purpose structure .......................................................................................................................... 186.2 Test purposes for the basic call .................................................................................................................. 186.2.1 Interworking from DSS1 to ISUP (Outgoing Call) ................................................................................ 186.2.1.1 Sending of the Initial Address Message (IAM) ................................................................................ 186.2.1.2 Sending of the Subsequent Address Message (SAM)....................................................................... 316.2.1.3 Receipt of the Address Complete Message (ACM).......................................................................... 326.2.1.4 Receipt of the Call progress message (CPG).................................................................................... 506.2.1.5 Receipt of the Answer message (ANM) .......................................................................................... 626.2.1.6 Receipt of the Connect message (CON) .......................................................................................... 726.2.1.7 Receipt of the Release message (REL) ............................................................................................ 816.2.1.8 Sending of the REL message........................................................................................................... 926.2.1.9 Receipt of Reset circuit message (RSC), Circuit group reset message (GRS) or Circuit group

blocking message (CGB) with the indication hardware failure oriented...........................................1236.2.1.9.1 Receipt of Reset Circuit message (RSC) ...................................................................................1236.2.1.9.2 Receipt of Circuit Group Reset message (GRS) ........................................................................1256.2.1.9.3 Receipt of Circuit Group blocking message (CGB) with the indication "hardware failure

oriented" ..................................................................................................................................1266.2.1.10 DSS1 Data link reset and Data Link failure procedures...................................................................1286.2.1.11 Receipt of the Suspend message (SUS) network initiated................................................................1316.2.1.12 Receipt of the Resume message (RES) network initiated ................................................................1316.2.1.13 Release by the exchange ................................................................................................................1316.2.1.14 Receipt of the release complete (RLC) ...........................................................................................1326.2.2 Interworking from Non-ISDN to ISUP (Outgoing Call) .......................................................................1376.2.2.1 Sending of the Initial address message (IAM).................................................................................1376.2.2.2 Receipt of the Address complete message (ACM) ..........................................................................1376.2.2.3 Receipt of the Call progress message (CPG)...................................................................................1376.2.2.4 Sending of the Release Message (REL) ..........................................................................................1386.2.2.5 Receipt of the Suspend message (SUS) network initiated................................................................1396.2.2.6 Receipt of the Resume message (RES) network initiated ................................................................1396.2.2.7 Release by the Exchange................................................................................................................139

ETSI


6.2.3 Interworking from ISUP to DSS1 ........................................................................................................1406.2.3.1 Sending of the SETUP message .....................................................................................................1406.2.3.2 Receipt of the SAM message .........................................................................................................1456.2.3.3 Sending of the ACM message ........................................................................................................1456.2.3.4 Sending of the CPG message .........................................................................................................1586.2.3.5 Sending of the ANM message........................................................................................................1706.2.3.6 Sending of the CON message.........................................................................................................1836.2.3.7 Receipt of the Release message (REL) ...........................................................................................1976.2.3.8 Sending of a REL message (REL)..................................................................................................2076.2.3.9 Receipt of Reset circuit message (RSC), Circuit group reset message (GRS) or Circuit group

blocking message (CGB) with the indication hardware failure oriented...........................................2236.2.3.9.1 Receipt of Reset Circuit message (RSC) ...................................................................................2236.2.3.9.2 Receipt of Circuit Group Reset message (GRS) ........................................................................2256.2.3.9.3 Receipt of Circuit Group blocking message (CGB) with the indication "hardware failure

oriented" ..................................................................................................................................2276.2.3.10 DSS1 Data link reset and Data Link failure procedures...................................................................2286.2.3.11 Release by the exchange ................................................................................................................2316.2.3.12 Receipt of the Release Complete message (RLC) ...........................................................................2336.2.4 Procedures for point-to-multipoint configurations with more than one terminal attached ......................2426.2.4.1 Sending of the Call progress message (CPG)..................................................................................2426.2.4.2 Sending of the Answer message (ANM).........................................................................................2536.2.4.3 Receipt of call clearing messages during call establishment ............................................................2566.2.5 Interworking from ISUP to Non-ISDN (Incoming Call) .......................................................................2586.2.5.1 Sending of the Ringing ..................................................................................................................2586.2.5.2 Receipt of the Subsequent address message (SAM) ........................................................................2586.2.5.3 Sending of the Address complete message (ACM) .........................................................................2596.2.5.4 Sending of the Call progress message (CPG)..................................................................................2606.2.5.5 Sending of the answer message (ANM)..........................................................................................2606.2.5.6 Receipt of the Release message (REL) ...........................................................................................2606.2.5.7 Sending of the Suspend message (SUS) network initiated...............................................................2616.2.5.8 Sending of the Resume message (RES) network initiated ...............................................................2626.3 Test purposes for the Supplementary Services...........................................................................................2626.3.1 Interworking from DSS1 to ISUP (Outgoing Call) ...............................................................................2626.3.1.1 Calling Line Identification Presentation (CLIP)..............................................................................2626.3.1.1.1 Special arrangement applies .....................................................................................................2626.3.1.1.2 Special arrangement does not apply ..........................................................................................2696.3.1.2 Calling Line Identification Restriction (CLIR) ...............................................................................2776.3.1.2.1 Special arrangement applies .....................................................................................................2776.3.1.2.2 Special arrangement does not apply ..........................................................................................2796.3.1.3 Connected Line Identification Presentation (COLP) .......................................................................2826.3.1.3.1 COLP subscribed .....................................................................................................................2826.3.1.3.2 COLP not subscribed................................................................................................................2966.3.1.4 Subaddressing (SUB).....................................................................................................................2976.3.1.5 Call diversion (CDIV) ...................................................................................................................2986.3.1.5.1 Reception of a "call is diverting" notification ............................................................................2986.3.1.5.2 Reception of the Redirection number restriction parameter........................................................3126.3.1.6 Call Waiting (CW).........................................................................................................................3306.3.1.7 Call Hold (HOLD).........................................................................................................................3326.3.1.7.1 Notification received from the network.....................................................................................3326.3.1.7.2 Invocation at coincident S and T reference point .......................................................................3336.3.1.7.3 Notification received at T reference point .................................................................................3356.3.1.8 Terminal Portability (TP)...............................................................................................................3366.3.1.8.1 Notification received from the network.....................................................................................3366.3.1.8.2 Invocation at coincident S and T reference point .......................................................................3376.3.1.8.3 Notification received at T reference point .................................................................................3386.3.1.9 Conference Calling (CONF) ..........................................................................................................3396.3.1.9.1 Notification received from the network.....................................................................................3396.3.1.9.2 Invocation at coincident S and T reference point .......................................................................3426.3.1.9.3 Notification at T reference point ...............................................................................................3466.3.1.10 Three-party (3PTY) .......................................................................................................................3506.3.1.10.1 Notification received from the network.....................................................................................3506.3.1.10.2 Invocation at coincident S and T reference point .......................................................................352

ETSI


6.3.1.10.3 Notification at T reference point ...............................................................................................3576.3.1.11 Closed User Group (CUG).............................................................................................................3586.3.1.11.1 CUG subscribed .......................................................................................................................3586.3.1.11.2 CUG not subscribed .................................................................................................................3656.3.1.12 User to User Signalling (UUS).......................................................................................................3666.3.1.12.1 Service 1 (UUS1) implicit ........................................................................................................3666.3.1.12.2 Service 1 (UUS1) explicit.........................................................................................................3706.3.1.12.3 Service 2 (UUS2) .....................................................................................................................3876.3.1.12.4 Service 3 (UUS3) .....................................................................................................................3966.3.1.13 Completion of Call to Busy Subscriber (CCBS) .............................................................................4076.3.1.13.1 S/T reference point...................................................................................................................4076.3.1.13.2 T reference point ......................................................................................................................4106.3.1.14 Explicit Call Transfer (ECT)..........................................................................................................4116.3.1.14.1 S/T reference point...................................................................................................................4116.3.1.14.1.1 Loop prevention procedure..................................................................................................4126.3.1.14.1.2 Service invocation ..............................................................................................................4226.3.1.14.2 T reference point ......................................................................................................................4276.3.1.14.2.1 Loop prevention procedure..................................................................................................4276.3.1.14.2.2 Service invocation ..............................................................................................................4286.3.1.15 Completion of Calls on No Reply (CCNR).....................................................................................4316.3.1.15.1 S/T reference point...................................................................................................................4316.3.1.15.2 T reference point ......................................................................................................................4356.3.2 Interworking from ISUP to DSS1 (Incoming Call)...............................................................................4376.3.2.1 Calling Line Identification Presentation (CLIP)..............................................................................4376.3.2.1.1 CLIP subscribed.......................................................................................................................4376.3.2.1.2 CLIP not subscribed .................................................................................................................4476.3.2.2 Connected Line Identification Presentation (COLP) .......................................................................4486.3.2.2.1 Special arrangement applies .....................................................................................................4486.3.2.2.2 Special arrangement does not apply ..........................................................................................4616.3.2.3 Connected Line Identification Restriction (COLR) .........................................................................4776.3.2.3.1 Special arrangement applies .....................................................................................................4786.3.2.3.2 Special arrangement does not apply ..........................................................................................4826.3.2.4 Subaddressing (SUB).....................................................................................................................4866.3.2.5 Call Diversion (CDIV)...................................................................................................................4876.3.2.6 Call Waiting (CW).........................................................................................................................5126.3.2.6.1 S/T reference point...................................................................................................................5126.3.2.6.2 T reference point ......................................................................................................................5136.3.2.7 Call Hold (HOLD).........................................................................................................................5156.3.2.7.1 Notification received from the network.....................................................................................5156.3.2.7.2 Invocation at coincident S and T reference point .......................................................................5176.3.2.7.3 Notification received at T reference point .................................................................................5186.3.2.8 Terminal Portability (TP)...............................................................................................................5196.3.2.8.1 Notification received from the network.....................................................................................5196.3.2.8.2 Invocation at coincident S and T reference point .......................................................................5206.3.2.8.3 Notification received at T reference point .................................................................................5216.3.2.9 Conference Calling (CONF) ..........................................................................................................5226.3.2.9.1 Notification received from the network.....................................................................................5226.3.2.9.2 Invocation at coincident S and T reference point .......................................................................5256.3.2.9.3 Notification at T reference point ...............................................................................................5296.3.2.10 Three-party (3PTY) .......................................................................................................................5336.3.2.10.1 Notification received from the network.....................................................................................5336.3.2.10.2 Invocation at coincident S and T reference point .......................................................................5356.3.2.10.3 Notification at T reference point ...............................................................................................5406.3.2.11 Closed User Group (CUG).............................................................................................................5416.3.2.11.1 CUG subscribed .......................................................................................................................5416.3.2.11.2 CUG not subscribed .................................................................................................................5476.3.2.12 User User Signalling (UUS)...........................................................................................................5476.3.2.12.1 Service 1 (UUS1) implicit ........................................................................................................5476.3.2.12.2 Service 1 (UUS1) explicit.........................................................................................................5526.3.2.12.3 Service 2 (UUS2) .....................................................................................................................5756.3.2.12.4 Service 3 (UUS3) .....................................................................................................................5886.3.2.13 Completion of Call to Busy Subscriber (CCBS) .............................................................................606

ETSI


6.3.2.13.1 S/T reference point...................................................................................................................6066.3.2.13.2 T reference point ......................................................................................................................6086.3.2.14 Explicit Call Transfer (ECT)..........................................................................................................6106.3.2.14.1 S/T reference point...................................................................................................................6106.3.2.14.2 T reference point ......................................................................................................................6386.3.2.14.2.1 Loop prevention procedure..................................................................................................6386.3.2.14.2.2 Service invocation ..............................................................................................................6406.3.2.15 Completion of Calls on No reply (CCNR) ......................................................................................6486.3.2.15.1 S/T reference point...................................................................................................................6486.3.2.15.2 T reference point ......................................................................................................................649

7 Test coverage.................................................................................................................................. 6517.1 General remarks .......................................................................................................................................651

Annex A (informative): Definition of causes values ....................................................................... 652

Annex B (informative): Bibliography............................................................................................. 670

History ..................................................................................................................................................... 671

ETSI


Intellectual Property RightsIPRs essential or potentially essential to the present document may have been declared to ETSI. The informationpertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be foundin ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI inrespect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Webserver (http://www.etsi.org/ipr).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guaranteecan be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Webserver) which are, or may be, or may become, essential to the present document.

ForewordThis European Standard (Telecommunications series) has been produced by ETSI Technical Committee Services andProtocols for Advanced Networks (SPAN), and is now submitted for the Vote phase of the ETSI standards Two-stepApproval Procedure.

The present document is part 3 of a multi-part deliverable covering the Integrated Services Digital Network (ISDN);Signalling System No.7; Interworking between ISDN User Part (ISUP) version 2 and Digital Subscriber SignallingSystem No. one (DSS1), as identified below:

Part 1: "Protocol specification [ITU-T Recommendation Q.699, modified]";

Part 2: "Protocol Implementation Conformance Statement (PICS) proforma specification";

Part 3: "Test Suite Structure and Test Purposes (TSS&TP) specification";

Part 4: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT)specification".

Proposed national transposition dates

Date of latest announcement of this EN (doa): 3 months after ETSI publication

Date of latest publication of new National Standardor endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

http://www.etsi.org/ipr

ETSI


1 ScopeThe present document specifies the network Test Suite Structure and Test Purposes (TSS&TP) for the interworkingbetween ISDN [6] and non-ISDN access and the ISDN User Part functions and protocol of Signalling System No. 7[2]-[5]. The interworking between the above signalling protocols is described in EN 300 899-1 [1] and occurs in anexchange with ISDN local exchange functionality and is specified in the context of a typical call in a pure ISDN ormixed ISDN/non-ISDN environment. The non-ISDN access defined in the present document means the analogue lineaccess. The present document applies only to exchanges having implemented the ISUP V2 protocol specification.

A further part of the present document specifies the Abstract Test Suite (ATS) and partial Protocol ImplementationeXtra Information for Testing (PIXIT) proforma based on the present document.

2 ReferencesThe following documents contain provisions which, through reference in this text, constitute provisions of the presentdocument.

• References are either specific (identified by date of publication and/or edition number or version number) ornon-specific.

• For a specific reference, subsequent revisions do not apply.

• For a non-specific reference, the latest version applies.

[1] ETSI EN 300 899-1: "Integrated Services Digital Network (ISDN); Signalling System No.7;Interworking between ISDN User Part (ISUP) version 2 and Digital Subscriber Signalling SystemNo. one (DSS1); Part 1: Protocol specification [ITU-T Recommendation Q.699, modified]".

[2] ITU-T Recommendation Q.761 (1997): "Functional description of the ISDN User Part ofSignalling System No. 7".

[3] ITU-T Recommendation Q.762 (1997): "General function of messages and signals of the ISDNUser Part of Signalling System No.7".

[4] ITU-T Recommendation Q.763 (1997): "Formats and codes of the ISDN User Part of SignallingSystem No.7".

[5] ETSI ETS 300 356-1 (1995): "Integrated Services Digital Network (ISDN); Signalling SystemNo.7; ISDN User Part (ISUP) version 2 for the international interface; Part 1: Basic services[ITU-T Recommendations Q.761 to Q.764 (1993), modified]".

[6] ETSI EN 300 403-1: "Integrated Services Digital Network (ISDN); Digital Subscriber SignallingSystem No. one (DSS1) protocol; Signalling network layer for circuit-mode basic call control;Part 1: Protocol specification [ITU-T Recommendation Q.931 (1993), modified]".

[7] ETSI EN 300 485: "Integrated Services Digital Network (ISDN); Definition and usage of causeand location in Digital Subscriber Signalling System No. one (DSS1) and Signalling System No. 7(SS7) ISDN User Part (ISUP) [ITU-T Recommendation Q.850 (1998) with addendum modified]".

[8] ISO/IEC 9646-1 (1994): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 1: General concepts".

[9] ISO/IEC 9646-3 (1998): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 3: The Tree and Tabular Combined Notation (TTCN)".

[10] ISO/IEC 9646-7 (1995): "Information technology - Open Systems Interconnection - Conformancetesting methodology and framework - Part 7: Implementation Conformance Statements".

[11] ITU-T Recommendation E.164: "Numbering in the ISDN era".

ETSI


[12] ETSI ETS 300 356-9 (1995): "Integrated Services Digital Network (ISDN); Signalling SystemNo.7; ISDN User Part (ISUP) version 2 for the international interface; Part 9: Closed User Group(CUG) supplementary service [ITU-T Recommendation Q.735, clause 1 (1993), modified]".

[13] ETSI EN 300 092-1: "Integrated Services Digital Network (ISDN); Calling Line IdentificationPresentation (CLIP) supplementary service; Digital Subscriber Signalling System No. one (DSS1)protocol; Part 1: Protocol specification".

[14] ETSI EN 300 093-1: "Integrated Services Digital Network (ISDN); Calling Line IdentificationRestriction (CLIR) supplementary service; Digital Subscriber Signalling System No. one (DSS1)protocol; Part 1: Protocol specification".

[15] ETSI EN 300 097-1: "Integrated Services Digital Network (ISDN); Connected Line IdentificationPresentation (COLP) supplementary service; Digital Subscriber Signalling System No. one(DSS1) protocol; Part 1: Protocol specification".

[16] ETSI EN 300 098-1: "Integrated Services Digital Network (ISDN); Connected Line IdentificationRestriction (COLR) supplementary service; Digital Subscriber Signalling System No. one (DSS1)protocol; Part 1: Protocol specification".

[17] ETSI EN 300 207-1: "Integrated Services Digital Network (ISDN); Diversion supplementaryservices; Digital Subscriber Signalling System No. One (DSS1); Part 1: Protocol specification".

[18] ETSI EN 300 061-1: "Integrated Services Digital Network (ISDN); Subaddressing (SUB)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[19] ETSI EN 300 058-1: "Integrated Services Digital Network (ISDN); Call Waiting (CW)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[20] ETSI EN 300 141-1: "Integrated Services Digital Network (ISDN); Call Hold (HOLD)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[21] ETSI EN 300 055-1: "Integrated Services Digital Network (ISDN); Terminal Portability (TP)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[22] ETSI EN 300 185-1: "Integrated Services Digital Network (ISDN); Conference call, add-on(CONF) supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[23] ETSI EN 300 188-1: "Integrated Services Digital Network (ISDN); Three-Party (3PTY)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[24] ETSI EN 300 138-1: "Integrated Services Digital Network (ISDN); Closed User Group (CUG)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[25] ETSI EN 300 286-1: "Integrated Services Digital Network (ISDN); User-to-User Signalling(UUS) supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

[26] ETSI EN 300 359-1: "Integrated Services Digital Network (ISDN); Completion of Calls to BusySubscriber (CCBS) supplementary service; Digital Subscriber Signalling System No. one (DSS1)protocol; Part 1: Protocol specification".

[27] ETSI EN 300 369-1: "Integrated Services Digital Network (ISDN); Explicit Call Transfer (ECT)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 1: Protocol specification".

ETSI


[28] ETSI EN 301 065-1: "Integrated Services Digital Network (ISDN); Completion of Calls on NoReply (CCNR) supplementary service; Digital Subscriber Signalling System No. one (DSS1)protocol; Part 1: Protocol specification".

[29] ETSI EN 300 356-20: "Integrated Services Digital Network (ISDN); Signalling System No.7(SS7); ISDN User Part (ISUP) version 4 for the international interface; Part 20: Completion ofCalls on No Reply (CCNR) supplementary service [ITU-T Recommendation Q.733, clause 5(1999) modified]".

[30] ETSI EN 300 138-2: "Integrated Services Digital Network (ISDN); Closed User Group (CUG)supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;Part 2: Protocol Implementation Conformance Statement (PICS) proforma specification".

[31] ITU-T Recommendation F.60: "Operational provisions for the international telex service".

[32] ITU-T Recommendation F.182: "Operational provisions for the international public facsimileservice between subscribers with Group 3 facsimile terminals (Telefax 3)".

[33] ITU-T Recommendation F.184: "Operational provisions for the international public facsimileservice between subscriber stations with group 4 facsimile terminals (telefax 4)".

[34] ITU-T Recommendation F.300: "Videotex service".

[35] ITU-T Recommendation F.721: "Videotelephony teleservice for ISDN".

[36] ITU-T Recommendation T.101: "International interworking for videotex services".

[37] ITU-T Recommendation T.102: "Syntax-based videotex end-to-end protocols for the circuit modeISDN".

[38] ITU-T Recommendation X.200 series: "Information technology - Open Systems Interconnection -Basic Reference Model: The basic model".

[39] ITU-T Recommendation X.400 series: "Message handling system and service overview".

ETSI


3 Definitions and abbreviations

3.1 DefinitionsFor the purposes of the present document, the terms and definitions given in:

• terms defined in ISDN/ISUP interworking reference specification [1];

• terms defined in ISDN layer 3 reference specification [6];

• terms defined in ISDN User Part (ISUP) reference specification [2]-[5];

• terms defined in ISO/IEC 9646-1 [8], ISO/IEC 9646-3 [9] and in ISO/IEC 9646-7 [10];

and the following apply:

Abstract Test Case (ATC): complete and independent specification of the actions required to achieve a specific testpurpose, defined at the level of abstraction of a particular Abstract Test Method, starting in a stable testing state andending in a stable testing state (see [8], clause 3.3.3)

Abstract Test Method (ATM): description of how an IUT is to be tested, given at an appropriate level of abstraction tomake the description independent of any particular realization of a Means of Testing, but with enough detail to enableabstract test cases to be specified for this method (see [8], clause 3.3.5)

Abstract Test Suite (ATS): test suite composed of abstract test cases (see [8], clause 3.3.6)

Implementation Under Test (IUT): implementation of one or more OSI protocols in an adjacent user/providerrelationship, being part of a real open system which is to be studied by testing (see [8], clause 3.3.43)

ISDN number: number conforming to the numbering and structure specified in ITU-T Recommendation E.164 [11]

Means of Testing (MOT): combination of equipment and procedures that can perform the derivation, selection,parameterization and execution of test cases, in conformance with a reference standardized ATS, and can produce aconformance log (see [8], clause 3.3.54)

PICS proforma: document, in the form of a questionnaire, which when completed for an implementation or systembecomes the PICS

PIXIT proforma: document, in the form of a questionnaire, which when completed for the IUT becomes the PIXIT

Point of Control and Observation: point within a testing environment where the occurrence of test events is to becontrolled and observed, as defined in an Abstract Test Method (see [8], clause 3.3.64)

Pre-test condition: setting or state in the IUT which cannot be achieved by providing stimulus from the testenvironment

Protocol Implementation Conformance Statement (PICS): statement made by the supplier of a protocol claimed toconform to a given specification, stating which capabilities have been implemented (see [8], clauses 3.3.39 and 3.3.80)

Protocol Implementation eXtra Information for Testing (PIXIT): statement made by a supplier or implementor ofan IUT (protocol) which contains or references all of the information related to the IUT and its testing environment,which will enable the test laboratory to run an appropriate test suite against the IUT (see [8], clauses 3.3.41 and 3.3.81)

System Under Test (SUT): real open system in which the IUT resides (see [8], clause 3.3.103)

User: access protocol entity at the User side of the user-network interface where a T reference point or coincident S andT reference point applies

ETSI


3.2 AbbreviationsThe ISUP message acronyms can be found in table 2/Q.762 [3].

For the purposes of the present document, the following abbreviations apply:

ATC Abstract Test CaseATM Abstract Test MethodATP Access Transport ParameterATS Abstract Test SuiteBC Bearer CapabilityBCI Backward Call IndicatorsCPS Calling Party's CategoryDSS1 Digital Subscriber System No. 1FCI Forward Call IndicatorsHLC High Layer CompatibilityISDN Integrated Services Digital NetworkISUP ISDN User PartIUT Implementation Under TestLLC Low Layer CompatibilityLT Lower TesterMMI Man Machine InterfaceMOT Means Of TestingMTC Main Test ComponentNCI Nature of Connection IndicatorsNNI Network-network interfaceOBCI Optional Backward Call IndicatorsPCO Point of Control and ObservationPDU Protocol Data UnitPICS Protocol Implementation Conformance StatementPIXIT Protocol Implementation eXtra Information for TestingSUT System Under TestTMR Transmission Medium RequirementTMU Transmission Medium UsedTP Test PurposeTSS&TP Test Suite Structure and Test PurposesTSS Test Suite StructureTTCN Tree and Tabular Combined NotationUNI User-network interface

ETSI


4 Implementation under test and test methods

4.1 Identification of the system and implementation under testThe system under test (SUT) is a local exchange where calls originate and terminate.

ISUP V2

DSS1 or Non-ISDN

UNIccess

NNIISUP V2

SUT

Exchangecapabilities and

functions

MMI

ISUP - ISDN User PartIUT - Implementation Under TestMMI - Man Machine InterfaceSUT - System Under Test

IUT

Figure 1: Exchange as SUT

The implementation under test (IUT) is the interworking implementation between the ISDN access or non-ISDN accesssignalling system and the ISUP V2 in this exchange, as shown in figure 1.

Circuit supervision is done mainly through the MMI (man machine interface) of the exchange. The MMI interface isimplementation dependent and thus not standardized.

The effects of ISDN access signalling procedures can be observed on the D-channel on the UNI (user-networkinterface). The ISUP signalling protocol can be observed on the SS No. 7 link on the network-network interface (NNI).

4.2 ATM and testing configurationThe Abstract Test Method (ATM) chosen for this testing specification is the distributed multiparty test method. TheATM is defined at an appropriate level of abstraction so that the test cases may be specified appropriately, withoutadding restrictions to the implementation under test. The testing architectures are described in the following clauses.

The ATS is written in concurrent TTCN.

4.2.1 Test method

The requirement for testing the network SUT is to focus on both the behaviour of the network SUT at the user-networkinterface where a T reference point or coincident S and T reference point applies and on the behaviour of the ISUPcircuit at the network-network interface.

It is possible to specify an ATS based on a Single party (remote) test method for such a SUT. However, it is consideredthat an ATS based on such an approach is of limited use as the only way to specify SUT generated PDUs is to use the"implicit send" statement. Many users of such an ATS would replace the "implicit send" statements with descriptions ofthe behaviour at other interfaces.

An ATS based on a multi-party test method is considered to be more useful in that it is closer to how a real test suitewould be constructed. Such a test method specifies behaviour at multiple network interfaces. The test system is made upof one Main Test Component (MTC) and one or more Parallel Test Components (PTC), see figure 2.

ETSI


To observe the mapping between DSS 1 layer 3 parameters and information elements and ISUP parameters andindicators, as defined in EN 300 899-1 [1], for each side a Point of Control and Observation (PCO) is needed. The PCOused by the LT to control the ISDN signalling is abbreviated with 'L1'; the ISUP signalling link is abbreviated with 'L2'.The ISDN and the ISUP PDUs to be sent and observed on the L1 and the L2 PCO side allow for PDU constraints to bespecified and coded down to the bit level.

Master part Slave part

MTCA

MTCACP2

CPA2

PTC2

PTC2

CP1

CPA1

PTC1

PTC1

L1 PCO L2 PCO

SUT

NETWORK

Figure 2: Test method

As EN 300 899-1 [1] focuses on the mapping between DSS 1 layer 3 parameters and information elements and ISUPparameters and indicators, no PCO for traffic channel functionality such as connectivity, tones and announcements isused in the present document.

In a master/slave arrangement, the MTC is considered to be the master while the PICS are the slaves. The MTC MTCAhas only one function in this configuration. It has the pure MTC function of controlling the two or more PICS. Thus it isresponsible for starting the PICS and afterwards coordinates activities by exchanging Coordination Messages (CM)with the PICS.

The "slave" testers are an explicit description of how to deal with the user-network and the network-network interfacesduring the testing process, i.e. "how to make the SUT send the required message".

ETSI


4.3 Untreatable test purposesThe test purposes of the two test groups:

- Interworking from Non-ISDN access to ISUP (outgoing call), TP20xxxx;

- Interworking from ISUP to Non-ISDN access (incoming call), TP40xxxx;

have not been converted into TTCN code, as the behaviour of the non-ISDN part can not be coded properly in TTCN,when using a test method as described above.

The test purposes of the two test groups:

- DSS1 Data link reset and Data Link failure procedures (outgoing call), TP111xxx;

- DSS1 Data link reset and Data Link failure procedures (incoming call), TP311xxx;

have not been converted into TTCN code, as the behaviour of the data link can not be coded properly in TTCN, whenusing a test method as described above.

5 Test Suite Structure (TSS)The Test Suite Structure is in close alignment with EN 300 899-1 [1].

5.1 Interworking from DSS1 to ISUP (outgoing call)DSS1-ISUP Basic call

Sending of the Initial address message (IAM) 101xxxSending of the Subsequent address message (SAM) 102xxxReceipt of the Address complete message (ACM) 103xxxReceipt of the Call progress message (CPG) 104xxxReceipt of the answer message (ANM) 105xxxReceipt of the Connect message (CON) 106xxxReceipt of the Release message (REL) 107xxxSending of the Release Message (REL) 108xxxReceipt of Reset circuit message (RSC), Circuit group resetmessage (GRS) or Circuit group blocking message (CGB) withthe indication hardware failure oriented

109xxx

DSS1 Data link reset and Data link failure procedures 111xxxReceipt of the Suspend message (SUS) network initiated 112xxxReceipt of the Resume message (RES) network initiated 113xxxRelease by the Exchange 114xxxReceipt of the release complete (RLC) 115xxx

Figure 3: Test suite structure for interworking between DSS1 to ISUP (outgoing call)

5.2 Interworking from Non-ISDN access to ISUP (outgoing call)Non -ISDN – ISUPBasic call

Sending of the Initial address message (IAM) 201xxxReceipt of the Address complete message (ACM) 202xxxReceipt of the Call progress message (CPG) 203xxxSending of the Release Message (REL) 204xxxReceipt of the Suspend message (SUS) network initiated 205xxxReceipt of the Resume message (RES) network initiated 206xxxRelease by the Exchange 207xxx

Figure 4: Test suite structure for interworking between Non-ISDN to ISUP (outgoing call)

ETSI


5.3 Interworking from ISUP to DSS1 (incoming call)ISUP-DSS1 Basic call

Sending of the SETUP message 301xxxReceipt of the Subsequent address message (SAM) 302xxxSending of the Address complete message (ACM) 303xxxSending of the Call progress message (CPG) 304xxxSending of the answer message (ANM) 305xxxSending of the Connect message (CON) 306xxxReceipt of the Release message (REL) 307xxxSending of the Release Message (REL) 308xxxReceipt of Reset circuit message (RSC), Circuit group resetmessage (GRS) or Circuit group blocking message (CGB) withthe indication hardware failure oriented

309xxx

DSS1 Data link reset and Data link failure procedures 311xxxRelease by the Exchange 312xxxThe following three test groups test the procedures for point-to-multipointconfigurations with more than one terminal attached.Receipt of the release complete (RLC) 313xxxSending of the Call progress message (CPG) 314xxxSending of the answer message (ANM) 315xxxReceipt of call clearing messages during call establishment 316xxx

Figure 5: Test suite structure for interworking between ISUP to DSS1 (incoming call)

5.4 Interworking from ISUP to Non-ISDN access (incoming call)ISUP - Non – ISDNBasic call

Sending of Ringing 401xxxReceipt of the Subsequent address message (SAM) 402xxxSending of the Address complete message (ACM) 403xxxSending of the Call progress message (CPG) 404xxxSending of the answer message (ANM) 405xxxReceipt of the Release message (REL) 406xxxSending of the Suspend message (SUS) network initiated 407xxxSending of the Resume message (RES) network initiated 408xxx

Figure 6: Test suite structure for interworking between ISUP to Non-ISDN (incoming call)

ETSI


5.5 Supplementary Services - Interworking from DSS1 to ISUP(outgoing call)

DSS1-ISUP Supplementary ServicesCalling Line Identification Presentation (CLIP) 501xxxCalling Line Identification Restriction (CLIR) 502xxxConnected Line Identification Presentation (COLP) 503xxxSubaddressing (SUB) 504xxxCall Diversion (CDIV) 505xxxCall Waiting (CW) 506xxxCall Hold (HOLD) 507xxxTerminal Portability (TP) 508xxxConference Calling (CONF) 509xxxThree-Party (3PTY) 510xxxClosed User Group (CUG) 511xxxUser to User Signalling (UUS) 512xxxCompletion of Call to Busy Subscriber (CCBS) 513xxxExplicit Call transfer (ECT) 514xxxCompletion of Calls on No reply (CCNR) 515xxx

Figure 7: Test suite structure for interworking between DSS1 to ISUP (outgoing call)

5.6 Supplementary Services - Interworking from ISUP to DSS1(incoming call)

ISUP-DSS1 Supplementary ServicesCalling Line Identification Presentation (CLIP) 601xxxConnected Line Identification Presentation (COLP) 602xxxConnected Line Identification Restriction (COLR) 603xxxSubaddressing (SUB) 604xxxCall Diversion (CDIV) 605xxxCall Waiting (CW) 606xxxCall Hold (HOLD) 607xxxTerminal Portability (TP) 608xxxConference Calling (CONF) 609xxxThree-Party (3PTY) 610xxxClosed User Group (CUG) 611xxxUser to User Signalling (UUS) 612xxxCompletion of Call to Busy Subscriber (CCBS) 613xxxExplicit Call transfer (ECT) 614xxxCompletion of Calls on No reply (CCNR) 615xxxSending of the answer message (ANM) 615xxx

Figure 8

ETSI


6 Test purposes (TP)

6.1 IntroductionFor each test requirement a Test Purpose (TP) is defined.

6.1.1 Test purpose (TP) naming convention

For each test requirement a Test Purpose (TP) is defined.

All test purposes belong to the main group ISUP_ISDN_Interworking. Groups are organized according to the test suitestructure (TSS). Each test purpose is presented in a separate table. The first row of the table contains the followingitems:

TP identifier of the test purpose;

ISDN reference the reference to the requirement in the DSS1 layer 3 Recommendation, which led to the TP;

ISUP reference the reference to the requirement in the interworking specification and the requirement in theISDN-UP Recommendation, which led to the TP.

6.1.2 Source of test purpose definition

The test purposes have been developed based on Recommendation EN 300 899-1 [1].

6.1.3 Test purpose structure

The test purpose structure is according to the test suite structure (TSS).

6.2 Test purposes for the basic call

6.2.1 Interworking from DSS1 to ISUP (Outgoing Call)

6.2.1.1 Sending of the Initial Address Message (IAM)

TP101001 ISDN reference:EN 300 403-1 [6], clause 5.1.1

ISUP reference:EN 300 899-1 [1], clause 2.1.1.1;

ETS 300 356-1 [5], clause 2.1TSS reference: DSS1-ISUP/Basic call/Sending of the Initial Address message (IAM)/ISDN selection

criteria:ISUP selection

criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a Called

party number information element providing the complete called party information andthe sending complete indication,

sends an IAM message.ISDN Parameter

values:SETUP; complete called party information elementSending complete information

ISUP Parametervalues:

IAM;

Comments: ISDN SETUP -> SUT -> IAM ISUP

ETSI



ISUP reference:EN 300 899-1 [1], clause 2.1.1.1;ETS 300 356-1 [5], clause 2.1.1

TSS reference: DSS1-ISUP/Basic call/Sending of the Initial Address message (IAM)/ISDN selection


criteria:use the en-bloc operation in the forward address signalling [A.3/1]

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message withoutinformation in the Called party number information element, followed byINFORMATION messages providing the additional digits and the last INFORMATIONmessage providing the sending complete information element


values:SETUP; no called party numberINFORMATION; additional digitslast INFORMATION; sending complete


IAM;


TP101003 ISDN reference:EN 300 403-1 [6], clause 5.1




criteria:use the overlap operation in the forward address signalling [A.3/2]

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message withoutinformation in the Called party number information element, followed by anINFORMATION message providing the complete called party information and the sendingcomplete information element,


values:SETUP; no called party numberINFORMATION: complete called party information elementsending complete


IAM;


ETSI







party number information element,sends an IAM message, with the Forward Call Indicators (FCI) encoded as follows:

Interworking indicator: "no interworking encountered"ISDN user part indicator: "ISDN user part used all the way"ISDN access indicator: "originating access ISDN"ISDN user part preference indicator: "ISDN user part preferred all the way"National/international call indicator set to FCI_NI_CALL_INDEnd-to-end method available set to FCI_EE_METHODEnd-to-End information indicator set to FCI_EE_INFO_INDSCCP method indicator set to FCI_SCCP_IND

and including the Calling party's category set to CGPG and the Nature of ConnectionIndicators (NCI) encoded as followed:

Satellite indicator set to NCI_SATE_INDContinuity check indicator set to NCI_CONT_CHECKEcho control device indicator set to NCI_ECHO_CTRL_IND

ISDN Parametervalues:

SETUP;


IAM; FCI Interworking indicator: no interworking encounteredFCI ISDN user part indicator: ISDN user part used all the wayFCI ISDN access indicator: originating access ISDNFCI ISDN user part preference indicator: ISDN user part preferred all the wayFCI National/international call indicator: FCI_NI_CALL_IND (PIXIT)FCI End-to-end method available: FCI_EE_METHOD (PIXIT)FCI End-to-End information indicator: FCI_EE_INFO_IND (PIXIT)FCI SCCP method indicator: FCI_SCCP_IND (PIXIT)Calling party's category: CGPGNCI Satellite indicator: NCI_SATE_INDNCI Continuity check indicator: NCI_CONT_CHECKNCI Echo control device indicator: NCI_ECHO_CTRL_IND



ISUP reference:EN 300 899-1 [1], clause 2.1.1.1 table 1;

ETS 300 356-1 [5], clause 2.1TSS reference: DSS1-ISUP/Basic call/Sending of the Initial Address message (IAM)/Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message containing one

Bearer Capability (BC) information transfer capability set to ISDN_BC_ITC and theinformation transfer rate set to ISDN_BC_ITR

sends an IAM message, with the Transmission Medium Requirement (TMR) parameterset to ISUP_TMR.


SETUP; BC information transfer capability: ISDN_BC_ITCBC information transfer rate: ISDN_BC_ITR


IAM; TMR : ISUP_TMR


ETSI


Values and selection criteria for the test purpose TP101005VA_01 ISDN_BC_ITC = speech ISUP_TMR = speech

ISDN selectioncriteria:

speech ([A.111/ISn1.2.1)]

ISUP selectioncriteria:

speech ([A.2/1])

VA_02 ISDN_BC_ITC = 3,1 kHz audio ISUP_TMR = 3,1 kHz audioISDN selection

criteria:3,1 kHz audio ([A.111/ISn1.2.4])


3,1 kHz audio ([A.2/2])

VA_03 ISDN_BC_ITC = unrestricted digital informationISDN_BC_ITR = 64 kbits/s unrestricted

ISUP_TMR = 64 kbits/s unrestricted


unrestricted digital ([A.111/ISn1.2.2]) AND 64 kbits/s ([A.111/ISn1.4.1])


64 kbits/s unrestricted ([A.2/3])

VA_04 ISDN_BC_ITC = unrestricted digital informationISDN_BC_ITR = 2 x 64 kbits/s unrestricted

ISUP_TMR = 2 x 64 kbits/s


unrestricted digital ([A.111/ISn1.2.2]) AND 2 x 64 kbits/s ([A.111/ISn1.4.2])


2 x 64 kbits/s ([A.2/6])

VA_05 ISDN_BC_ITC = unrestricted digital informationISDN_BC_ITR = 384 kbits/s unrestricted

ISUP_TMR = 384 kbits/s


unrestricted digital ([A.111/ISn1.2.2]) AND 384 kbits/s ([A.111/ISn1.4.3])


384 kbits/s ([A.2/7])

VA_06 ISDN_BC_ITC = unrestricted digital informationISDN_BC_ITR = 1 536 kbits/s unrestricted

ISUP_TMR = 1 536 kbits/s


unrestricted digital ([A.111/ISn1.2.2]) AND 1 536 kbits/s ([A.111/ISn1.4.4])


1 536 kbits/s ([A.2/8])

VA_07 ISDN_BC_ITC = unrestricted digital informationISDN_BC_ITR = 1 920 kbits/s unrestricted



unrestricted digital ([A.111/ISn1.2.2]) AND 1 920 kbits/s ([A.111/ISn1.4.5])


1 920 kbits/s ([A.2/9])

VA_08 ISDN_BC_ITC = unrestricted digital informationISDN_BC_ITR = multirate: 6 x 64 kbits/s



unrestricted digital ([A.111/ISn1.2.2]) AND multirate ([A.111/ISn1.4.6]) AND ratemultiplier = 6 ([A.111/ISn1.9] = 6)


384 kbits/s ([A.2/7])






1 536 kbits/s ([A.2/8])






1 920 kbits/s ([A.2/9])

VA_11 ISDN_BC_ITC = unrestricted digital informationwith tones/announcementsISDN_BC_ITR = 64 kbits/s unrestricted

ISUP_TMR = 64 kbits/s unrestricted


unrestricted digital with tones/announcements ([A.111/ISn1.2.5]) AND 64 kbits/s([A.111/ISn1.4.1])


64 kbits/s unrestricted ([A.2/3])

ETSI


Values and selection criteria for the test purpose TP101005VA_12 ISDN_BC_ITC = unrestricted digital information

with tones/announcementsISDN_BC_ITR = 2 x 64 kbits/s unrestricted

ISUP_TMR = 2 x 64 kbits/s


unrestricted digital with tones/announcements ([A.111/ISn1.2.5]) AND 2 x 64 kbits/s([A.111/ISn1.4.2])


2 x 64 kbits/s ([A.2/6])

VA_13 ISDN_BC_ITC = unrestricted digital informationwith tones/announcementsISDN_BC_ITR = 384 kbits/s unrestricted



unrestricted digital with tones/announcements ([A.111/ISn1.2.5]) AND 384 kbits/s([A.111/ISn1.4.3])


384 kbits/s ([A.2/7])

VA_14 ISDN_BC_ITC = unrestricted digital informationwith tones/announcementsISDN_BC_ITR = 1 536 kbits/s unrestricted



unrestricted digital with tones/announcements ([A.111/ISn1.2.5]) AND 1 536 kbits/s([A.111/ISn1.4.4])


1 536 kbits/s ([A.2/8])

VA_15 ISDN_BC_ITC = unrestricted digital informationwith tones/announcementsISDN_BC_ITR = 1 920 kbits/s unrestricted



unrestricted digital with tones/announcements ([A.111/ISn1.2.5]) AND 1 920 kbits/s([A.111/ISn1.4.5])


1 920 kbits/s ([A.2/9])

VA_16 ISDN_BC_ITC = unrestricted digital informationwith tones/announcementsISDN_BC_ITR = multirate: 6 x 64 kbits/s



unrestricted digital with tones/announcements ([A.111/ISn1.2.5]) AND multirate([A.111/ISn1.4.6]) AND rate multiplier = 6 ([A.111/ISn1.9] = 6)


384 kbits/s ([A.2/7])






1 536 kbits/s ([A.2/8])






1 920 kbits/s ([A.2/9])

ETSI





criteria:speech ([A.111/ISn1.2.1]) AND unrestricted digital information with tones/announcements([A.111/ISn.1.2.5])


support 64 kbits/s unrestricted preferred ([A.2/4]) AND speech ([A.2/1]) AND supportsignalling procedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with the firstBearer Capability information transfer capability set to "speech" and the secondBearer Capability information transfer capability set to "unrestricted digital informationwith tones/announcements"

sends an IAM message, with the transmission medium requirement parameter setto "64 kbits/s unrestricted preferred".


SETUP; first BC: speechsecond BC: unrestricted digital information with tones/announcements


IAM; Transmission medium requirement : 64 kbits/s unrestricted preferred



ISUP reference:EN 300 899-1 [1], clause 2.1.1.1 table 2,


criteria:3,1 kHz audio ([A.111/ISn1.2.2]) AND unrestricted digital information withtones/announcements ([A.111/ISn.1.2.5])


support 64 kbits/s unrestricted preferred ([A.2/4]) AND 3,1 kHz audio ([A.2/2]) ANDsupport signalling procedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with the firstBearer Capability information transfer capability set to "3,1 kHz audio" and the secondBearer Capability information transfer capability set to "unrestricted digital informationwith tones/announcements"

sends an IAM message, with the transmission medium requirement parameter setto "64 kbits/s unrestricted preferred".


SETUP; first BC: 3,1 kHz audiosecond BC: unrestricted digital information with tones/announcements


IAM; Transmission medium requirement : 64 kbits/s unrestricted preferred







party number information element providing the complete called party information andthe sending complete indication, sends an IAM message, with the called party numberencoded as following:

Internal network numbering set to "routing to internal network number not allowed"numbering plan indicator set to "ISDN (Telephony) numbering plan"


SETUP; complete called party informationsending complete indication included


IAM; called party number Internal network numbering: routing to internal networknumber not allowedcalled party number numbering plan indicator : ISDN (Telephony) numbering plan


ETSI






criteria:use the en-bloc operation in the forward address signalling ([A.3/1]) OR use the overlapoperation in the forward address signalling ([A.3/2]) AND support signalling procedures forconnection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a Calledparty number information element providing the complete called party information andthe sending complete indication,

sends an IAM message, with the called party number with the address signalcontaining the called number information received in the SETUP


SETUP; complete called party information: ISDN_CDPNsending complete indication included


IAM; called party number address signal: the called number information received in theSETUP






criteria:use the en-bloc operation in the forward address signalling [A.3/1] AND NOT(use theoverlap operation in the forward address signalling [A.3/2])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message withoutinformation in the Called party number information element, followed by anINFORMATION message providing the complete called party information and the sendingcomplete information,

sends an IAM message, with the called party number encoded as following:Internal network numbering set to "routing to internal network number not

allowed"numbering plan indicator set to "ISDN (Telephony) numbering plan".


SETUP; no called party numberINFORMATION; complete called party informationsending complete indication


IAM; called party number Internal network numbering: routing to internal networknumber not allowedcalled party number numbering plan indicator: ISDN (Telephony) numbering plan


ETSI






criteria:use the en-bloc operation in the forward address signalling [A.3/1] AND NOT(use theoverlap operation in the forward address signalling [A.3/2])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message withoutinformation in the Called party number information element, followed by anINFORMATION message providing the complete called party information and the sendingcomplete information,

sends an IAM message, with the complete called party number address signalcontaining the called number information received in the SETUP and in theINFORMATION messages.


SETUP; no called party numberINFORMATION; called party information: ISDN_CDPNsending complete indication included


IAM; called party number address signal: ISUP_ADDRESS_SIGNAL






criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a valid

Progress indicatorsends an IAM message with the Access transport parameter containing the same

progress indicator information element as in the SETUP message.ISDN Parameter

values:SETUP; progress indicator: PI_VALUE


IAM; progress indicator PI_VALUE

Comments: ISDN SETUP -> SUT -> IAM ISUPThe PIXIT value could have a valid or invalid format

Values and selection criteria for the test purpose TP101012VA_01 PI_VALUE = Call is not end-to-end ISDN; further call progress information may be

available in-band (# 1)VA_02 PI_VALUE = Originating access is non ISDN (#3)

ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with BC_VALUE

and the High Layer Compatibility HLC_VALUEsends an IAM message with the Access transport parameter containing the same HLC

information element as in the SETUP message.ISDN Parameter

values:SETUP;BC: BC_VALUEHLC: HLC_VALUE


IAM; Access transport parameter HLC: HLC_VALUE


Values and selection criteria for the test purpose TP101014VA_01 HLC_VALUE = Telephony

BC_VALUE = speechVA_02 HLC_VALUE = Facsimile Group 2/3 (ITU-T Recommendation F.182 [32])

BC_VALUE = 3,1 kHz audioVA_03 HLC_VALUE == Facsimile Group 4 Class I (ITU-T Recommendation F.184 [33])

BC_VALUE = Unrestricted digital informationVA_04 HLC_VALUE == Teletex service, basic and mixed mode of operation

(ITU-T Recommendation F.230) and facsimile service Group 4, Classes II and III(ITU-T Recommendation F.184 [33])BC_VALUE = Unrestricted digital information

VA_05 HLC_VALUE == Teletex service, basic and processable mode of operation(ITU-T Recommendation F.220)BC_VALUE = Unrestricted digital information

VA_06 HLC_VALUE = Teletex service, basic mode of operation (ITU-T Recommendation F.200)BC_VALUE = Unrestricted digital information

VA_07 HLC_VALUE = Syntax based Videotex (ITU-T Recommendations F.300 [34] andT.102 [37])BC_VALUE = Unrestricted digital information

VA_08 HLC_VALUE = International Videotex interworking via gateways or interworking units(ITU-T Recommendations F.300 [34] and T.101 [36])BC_VALUE = Unrestricted digital information

VA_09 HLC_VALUE = Telex service (ITU-T Recommendation F.60 [31])BC_VALUE = Unrestricted digital information

VA_10 HLC_VALUE = Message Handling Systems (MHS)(X.400 - Series ITU-T Recommendations [39])BC_VALUE = Unrestricted digital information

VA_11 HLC_VALUE = OSI application (note 2) (X.200 - Series ITU-T Recommendations [38])BC_VALUE = Unrestricted digital information

VA_12 HLC_VALUE = Audio visual (ITU-T Recommendation F.721 [35])BC_VALUE = Unrestricted digital information

ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a Low Layer

Compatibility (LLC)sends an IAM message with the Access transport parameter containing the same LLC

information element as in the SETUP message.ISDN Parameter

values:SETUP; LLC: LLC_VALUE (PIXIT)


IAM; Access transport parameter LLC: LLC_VALUE (PIXIT)





criteria:speech ([A.111/ISn.1.2.1]) AND unrestricted digital information with tones/announcements([A.111/ISn.1.2.5])


speech ([A.2/1])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with the firstBearer Capability information transfer capability set to "speech" and the second BearerCapability information transfer capability set to "unrestricted digital information withtones/announcements"

sends an IAM message, with the user information parameter transfer capabilityinformation element set to "speech".


SETUP; first BC information transfer capability: speechsecond BC information transfer capability: unrestricted digital information withtones/announcements


IAM; User information parameter: speech



ISUP reference:EN 300 899-1 [1], clause 2.1.1.1 table 4;ETS 300 356-1 [5], clauses 2.1 and 2.5


criteria:3,1 kHz audio ([A.111/ISn.1.2.2]) AND unrestricted digital information withtones/announcements ([A.111/ISn.1.2.5])


3,1 kHz audio ([A.2/2])


sends an IAM message, with the user information parameter transfer capability set to"3,1 kHz audio".


SETUP; first BC information transfer capability: 3,1 kHz audiosecond BC information transfer capability: unrestricted digital information withtones/announcements


IAM; User information parameter: 3,1 kHz audio


ETSI



ISUP reference:EN 300 899-1 [1], clause 2.1.1.1 table 4;ETS 300 356-1 [5], clauses 2.1 and 2.5



criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with one Bearer

Capabilitysends an IAM message, with the user information parameter set to the value of the BC

information transfer capability and information transfer rate of the SETUP message.ISDN Parameter

values:SETUP;BC: : BC_VALUE (PIXIT)


IAM; User information parameter: BC_VALUE (PIXIT)







64 kbits/s unrestricted preferred ([A.2/4]) AND speech ([A.2/1]) AND support signallingprocedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with the firstBearer Capability set to "speech" and the second bearer capability set to "unrestricteddigital information with tones/announcements"

sends an IAM message, with the user information prime parameter set to the value ofthe second BC and information transfer rate of the SETUP message.


SETUP;BC1 : speechBC2: unrestricted digital information with tones/announcements


IAM; User information prime parameter: unrestricted digital information withtones/announcements







64 kbits/s unrestricted preferred ([A.2/4]) AND 3,1 kHz audio ([A.2/2]) AND supportsignalling procedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with the firstBearer Capability set to "3,1 kHz audio" and the second bearer capability set to"unrestricted digital information with tones/announcements"

sends an IAM message, with the user information prime parameter set to the valueof the second BC and information transfer rate of the SETUP message.


SETUP;BC1: 3,1 kHz audioBC2: "unrestricted digital information with tones/announcements"


IAM; User information prime parameter: unrestricted digital information withtones/announcements


ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a High Layer

Compatibility (HLC)sends an IAM message with the User teleservice information parameter containing the

same HLC information element as in the SETUP message.ISDN Parameter

values:SETUP; HLC: HLC_VALUE (PIXIT)


IAM; User teleservice information parameter HLC: HLC_VALUE (PIXIT)






criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with two High

Layer Compatibility (HLC)sends an IAM message with the User teleservice information parameter containing

the second HLC information element as in the SETUP message.ISDN Parameter

values:SETUP; first HLC: HLC_VALUE1 (PIXIT)second HLC2: HLC_VALUE2 (PIXIT)


IAM; User teleservice information parameter HLC: HLC_VALUE2 (PIXIT)







64 kbits/s unrestricted preferred ([A.2/4]) AND 3,1 kHz audio ([A.2/2]) AND supportsignalling procedures for connection type allowing fallback ([A.13/10])


sends an IAM message, with the transmission medium requirement primeparameter set to "3,1 kHz audio".


SETUP; first BC information transfer capability: 3,1 kHz audiosecond BC information transfer capability: unrestricted digital information withtones/announcements


IAM; transmission medium requirement prime parameter: 3,1 kHz audio


ETSI






criteria:NOT (support signalling procedures for connection type allowing fallback [A.13/10])

Test purpose: Ensure that the SUT in the Idle state, not supporting the fallback procedure, on receiptof a SETUP message including a two Bearer capability: BC1 and BC2

sends an IAM message with the Transmission medium requirement with theencoding corresponding to BC1, the User information parameter set to BC1 andincluding no Transmission medium requirement prime parameter and no Userinformation prime parameter.


SETUP;BC1: ISDN_BC1_VALUEBC2: ISDN_BC2_VALUE


IAM; Transmission medium requirement: ISUP_BC1_VALUEUser information parameter: ISDN_BC1_VALUETransmission medium requirement prime: not includedUser information prime parameter: not included







64 kbits/s unrestricted preferred ([A.2/4]) AND speech ([A.2/1]) AND support signallingprocedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message, with the firstBearer Capability information transfer capability set to "speech" and the secondBearer Capability information transfer capability set to "unrestricted digital informationwith tones/announcements"

sends an IAM message, with the transmission medium requirement primeparameter set to "speech".


SETUP; first BC information transfer capability: speechsecond BC information transfer capability: unrestricted digital information withtones/announcements


IAM; transmission medium requirement prime: speech






criteria:send the end-of pulsing signal (ST) ([A.4/1])

Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a Calledparty number information element providing the complete called party information, andwith a sending complete information element

sends an IAM message with the sending complete indication 'ST'.ISDN Parameter

values:SETUP; called party information: completesending complete information element


IAM; sending complete 'ST'


ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state on receipt of a SETUP message with a Calling

party number set to ISDN_CGPNsends an IAM message with the calling party set to ISUP_CGPN


SETUP; Calling party number NPI: ISDN_CGPN (PIXIT)


IAM; calling party: ISUP_CGPN


6.2.1.2 Sending of the Subsequent Address Message (SAM)

102001 ISDN reference:EN 300 403-1 [6], clause 5.1.3


TSS reference: DSS1-ISUP/Basic call/Sending of the Subsequent Address Message (SAM)/ISDN selection


criteria:use the overlap operation in the forward address signalling [A.3/2]

Test purpose: Ensure that the SUT in call state N2 having sent the IAM message, on receipt of anINFORMATION message providing additional digits without sending complete indication,

sends a SAM message, containing this additional digit.ISDN Parameter

values:INFORMATION messages; additional digits (PIXIT)


SAM; subsequent number (PIXIT)

Comments: ISDN INFORMATION -> SUT -> SAM ISUP

102002 ISDN reference:EN 300 403-1 [6], clause 5.1.3


TSS reference: DSS1-ISUP/Basic call/Sending of the Subsequent Address Message (SAM)/ISDN selection


criteria:use the overlap operation in the forward address signalling [A.3/2] AND send the end-ofpulsing signal (ST) ([A.4/1])

Test purpose: Ensure that the SUT in call state N2 having sent the IAM message, on receipt of anINFORMATION message providing additional digits and with a sending completeinformation element included,

sends a SAM message, containing this additional digit and the sending completeindication 'ST'.


INFORMATION; called party number: additional digits (PIXIT)sending complete information


SAM; sending complete: 'ST'

Comments: ISDN INFORMATION -> SUT -> SAM ISUP

ETSI


6.2.1.3 Receipt of the Address Complete Message (ACM)


ISUP reference:EN 300 899-1 [1], clause 2.1.1.3.2 table 9;

ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM)/ISDN selection


criteria:Test purpose: Ensure that the SUT in the state N2 on receipt of an ACM message where the CPS

indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no",

sends a CALL PROCEEDING,ISDN Parameter

values:CALL PROCEEDING;


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: no

Comments: ISUP ACM -> SUT -> CALL PROCEEDING ISDN






indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way", theISDN access indicator is set to "ISDN" and the OBCI with the in-band information is set to"Yes"

sends a CALL PROCEEDING message with a progress indicator "in-band informationor appropriate pattern now available (#8)".


CALL PROCEEDING; progress indicator "in-band information or appropriate pattern nowavailable (#8)" location "public network serving local user"


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: Yes


ETSI





criteria:speech ([A.111/ISn.1.2.1]) OR 3,1 kHz audio ([A.111/ISn.1.2.2])


Test purpose: Ensure that the SUT in the state N2 on receipt of an ACM message where the CPSindicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way", theISDN access indicator is set to "non-ISDN" and the OBCI with the in-band information isset to "Yes"

sends a CALL PROCEEDING message with two progress indicators "destinationaddress is non-ISDN (#2)" location "public network serving local user" and "in-bandinformation or appropriate pattern now available (#8)".


CALL PROCEEDING; progress indicator:in-band information or appropriate pattern now available (#8) location "public networkserving local user destination address is non-ISDN (#2)" location "public network servinglocal user"


ACM; CPS indicator: no indication,ISUP indicator: "ISUP is used all the way"ISDN access indicator: non-ISDNOBCI with the in-band information: Yes







Test purpose: Ensure that the SUT in the state N2, on receipt of an ACM message where the CPSindicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way", theISDN access indicator is set to "non-ISDN" and the OBCI with the in-band information isset to "No"

sends a CALL PROCEEDING message with a progress indicator with the progressdescriptions "destination address is non-ISDN (#2)".


CALL PROCEEDING; progress indicator: destination address is non-ISDN (#2) location"public network" serving local user


ACM: CPS indicator : no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNOBCI with the in-band information: No







indicator is set to "no indication", the ISUP indicator is set to "ISUP not used all the way",sends a CALL PROCEEDING message with a progress indicator "call is not end-to-end

ISDN, further call progress information may be available in-band (#1)".ISDN Parameter

values:CALL PROCEEDING; progress indicator call is not end-to-end ISDN, further call progressinformation may be available in-band (#1)" location "network beyond an interworking point"


ACM; CPS indicator: no indication,ISUP indicator: ISUP not used all the way


ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP used all the way", theISDN access indicator set to "ISDN", the Access Transport Parameter (ATP) containingthe progress indicator set to PI_VALUE

sends a CALL PROCEEDING message with a progress indicator set to PI_VALUE,"ISDN Parameter

values:CALL PROCEEDING; progress indicator: PI_VALUE


ACM, CPS indicator: no indication (00)Called party's category indicator: no indication(00) or ordinary subscriber (01) orpayphone (10)interworking indicator: no interworking encountered (0)ISUP indicator: ISUP used all the wayISDN access indicator: ISDNATP progress indicator: PI_VALUEaccess delivery information: Set-up message generated (IF PRESENT)







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN"

sends an ALERTING.ISDN Parameter

values:ALERTING;


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDN

Comments: ISUP ACM -> SUT -> ALERTING ISDN



ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Call progress message (ACM).ISDN selection


criteria:Test purpose: Ensure that the SUT in the state N2, having received the ACM message, where the CPS

indicator is set to "subscriber free" where the ISUP indicator parameter set to ISUP_ID,the ISDN access indicator set to ISDN_ACCES_ID and the OBCI in-band information setto OBCI_INBAND

sends an ALERTING message with the progress indicator information element set toPI_ID.


ALERTING; progress indicator: PI_ID


CPG; event information parameter event indicator: AlertingISUP indicator: ISUP_IDISDN access indicator: ISDN_ACCES_ID

Comments: ISUP CPG -> SUT -> ALERTING ISDN

ETSI


Values for test purposes TP103008test purposes ISUP Parameter values: ISDN Parameter values:

VA_01 ACMISUP_ID: ISUP not used all the wayOBCI_INBAND: no

PI_ID: Call is not end-to-end ISDN (#1)

VA_02 ACMISUP_ID: ISUP not used all the wayOBCI_INBAND: yes

PI_ID: Call is not end-to-end ISDN(#1)and In-band information orappropriate pattern now available (#8)

VA_03 ACMISUP_ID: ISUP used all the wayISDN_ACCES_ID: non ISDNOBCI_INBAND: no

PI_ID: Destination address is non-ISDN(#2)

VA_04 ACMISUP_ID: ISUP used all the wayISDN_ACCES_ID: non ISDNOBCI_INBAND: yes

PI_ID: Destination address is non-ISDN(#2) and In-band information orappropriate pattern now available (#8)

VA_05 ACMISUP_ID: ISUP used all the wayISDN access indicator: ISDNOBCI_INBAND: yes

PI_ID: In-band information orappropriate pattern now available (#8)






indicator is set to "subscriber free", the ISUP indicator is set to "ISUP used all the way", theISDN access indicator is set to "ISDN" and the ATP containing the progress indicatorPI_VALUE.

sends a ALERTING message containing a progress indicator set to PI_VALUEISDN Parameter

values:ALERTING; progress indicator: call is not end-to-end ISDN, further call progressinformation may be available in-band (#1) location network beyond an interworking point


ACM; CPS indicator: "subscriber free"ISUP indicator: ISUP used all the wayISDN access indicator: ISDNATP progress indicator: PI_VALUE








sends no messageISDN Parameter

values:ISUP Parameter

values:ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: no

Comments: ISUP ACM -> SUT -> no action

ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the Access Transport Parameter (ATP)containing the progress indicator set to PI_VALUE

sends a PROGRESS message containing a progress indicator PI_VALUEISDN Parameter

values:PROGRESS; progress indicator: PI_VALUE (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNATP progress indicator: PI_VALUE

Comments: ISUP ACM -> SUT -> PROGRESS ISDN





criteria:Test purpose: Ensure that the SUT in the state N3, on receipt of an ACM message where the CPS

indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "yes",

sends a PROGRESS message including a progress indicator "in-band information orappropriate pattern now available (#8)".


PROGRESS; progress indicator "in-band information or appropriate pattern now available(#8)" location "public network serving local user"


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: yes

Comments: ISUP ACM -> SUT -> PROGRESS

ETSI







Test purpose: Ensure that the SUT in the state N3 on receipt of an ACM message where the CPSindicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "non-ISDN" and the OBCI with the in-band informationis set to "Yes"

sends a PROGRESS message including a progress indicator I.E. with two descriptions"destination address is non-ISDN (#2)" location "public network serving local user" and "in-band information or appropriate pattern now available (#8)".


PROGRESS; progress indicator: in-band information or appropriate pattern now available(#8)"location "public network serving local user destination address is non-ISDN (#2)"location "public network serving local user"


ACM; CPS indicator: no indication,ISUP indicator: "ISUP is used all the way"ISDN access indicator: non-ISDNOBCI with the in-band information: Yes







Test purpose: Ensure that the SUT in the state N3 on receipt of an ACM message where the CPSindicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "non-ISDN" and the OBCI with the in-band informationis set to "No"

sends a PROGRESS message with a progress indicator with the progressdescriptions "destination address is non-ISDN (#2)".


PROGRESS; progress indicator: destination address is non-ISDN (#2) location "publicnetwork serving local user


ACM: CPS indicator : no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNOBCI with the in-band information: No







indicator is set to "no indication", the ISUP indicator is set to "ISUP not used all the way",sends a PROGRESS message with a progress indicator with the progress

descriptions "call is not end-to-end ISDN, further call progress information may be availablein-band (#1).


PROGRESS; progress indicator call is not end-to-end ISDN, further call progressinformation may be available in-band (#1)" location "network beyond an interworking point"


ACM; CPS indicator: no indication,ISUP indicator: ISUP not used all the way


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN"

sends an ALERTING.ISDN Parameter

values:ALERTING;


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDN




ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Call progress message (ACM).ISDN selection


criteria:Test purpose: Ensure that the SUT in the state N3, having received the ACM message, where the CPS

indicator is set to "subscriber free" where the ISUP indicator parameter set to ISUP_ID,the ISDN access indicator set to ISDN_ACCES_ID and the OBCI in-band information setto OBCI_INBAND








VA_01 ACMISUP_ID: ISUP not used all the way


VA_02 ACMISUP_ID: ISUP not used all the wayOBCI_INBAND: yes

PI_ID: Call is not end-to-end ISDN(#1)and In-band information orappropriate pattern now available (#8)

VA_03 ACMISUP_ID: ISUP used all the wayISDN_ACCES_ID: non ISDNOBCI_INBAND: no


VA_04 ACMISUP_ID: ISUP used all the wayISDN_ACCES_ID: non ISDNOBCI_INBAND: yes


VA_05 ACMISUP_ID: ISUP used all the wayISDN access indicator: ISDNOBCI_INBAND: yes


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP used all the way", theISDN access indicator is set to "ISDN" and the ATP containing the progress indicatorPI_VALUE.

sends a ALERTING message containing a progress indicator set to PI_VALUEISDN Parameter

values:ALERTING; progress indicator: PI_VALUE


ACM; CPS indicator: "subscriber free"ISUP indicator: ISUP used all the wayISDN access indicator: ISDNATP progress indicator: PI_VALUE




ETS 300 356-1 [5], clauses 2.1.4, 2.2TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM)/ISDN selection



indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the Transmission Medium Used (TMU) isincluded with the value ISDN_BC_VALUE and the Access Transport Parameter (ATP) setto ATP_VALUE.

sends an ALERTING message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5);and with the BC encoded ISDN_BC_VALUE


SETUP; first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2ALERTING; progress indicator : interworking has occurred and has resulted in atelecommunication service change (#5)BC : ISDN_BC_VALUE


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNTMU : TMU_VALUEATP: BC ATP_VALUE


ETSI


Values and selection criteria for test purpose TP103019Test purposes ACM Parameter values ALERTING Parameter

values:SETUP parameter value

VA_01 TMU_VALUE : speechATP_VALUE : no BC

ISDN_BC_VALUE :speech

SETUP_BC1: speechSETUP_BC2: unrestricted digitalinformation with tones andannouncements


speech ([A.111/ISn.1.2.1]) AND unrestricted digital information with tones andannouncements ([A.111/ISn.1.2.5])


support signalling procedures for connection type allowing fallback ([A.13/10]) AND

64 kbits/s unrestricted preferred ([A.2/4]) AND speech ([A.2/1])

VA_02 TMU_VALUE : 3,1 kHzATP_VALUE: no BC

ISDN_BC_VALUE :3,1 kHz audio

SETUP_BC1: 3,1 kHz audioSETUP_BC2: unrestricted digitalinformation with tones andannouncements


3,1 kHz audio ([A.111/Isn.1.2.4]) AND unrestricted digital information with tones andannouncements ([A.111/ISn.1.2.5])



64 kbits/s unrestricted preferred ([A.2/4]) AND 3,1 kHz audio ([A.2/2])

VA_03 TMU_VALUE : speechATP_VALUE:BC = 3,1 kHz








VA_04 TMU_VALUE : speechATP_VALUE:BC = speech








VA_05 TMU_VALUE : 3,1 kHzATP_VALUE:BC = speech








VA_06 TMU_VALUE :3,1 kHz audioATP_VALUE:BC = 3,1 kHz audio








ETSI




ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM)/Test purpose: Ensure that the SUT in the state N2 on receipt of an ACM message where the CPS

indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way", theISDN access indicator is set to "ISDN" and the Transmission Medium Used (TMU) isincluded with the value TMU_VALUE and the Access Transport Parameter (ATP) set toATP_VALUE.

sends a CALL PROCEEDING message with a progress indicator with the progressindication "interworking has occurred and has resulted in a telecommunication servicechange" (#5); and with the BC encoded ISDN_BC_VALUE




ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNTMU : TMU_VALUEATP: BC ATP_VALUE


ETSI


Values and selection criteria for test purpose TP103020Test purposes ACM Parameter values CALL PROCEEDING

Parameter values:SETUP parameter value

















































ETSI




ETS 300 356-1 [5], clauses 2.1.4, 2.2TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM)/Test purpose: Ensure that the SUT in the state N3 on receipt of an ACM message where the CPS

indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the Transmission Medium Used (TMU) isincluded with the value ISDN_BC_VALUE and the Access Transport Parameter (ATP) setto ATP_VALUE.

sends an ALERTING message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5);and with the BC encoded ISDN_BC_VALUE




ACM; CPS indicator: subscriber free,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNTMU : TMU_VALUEATP: BC ATP_VALUE


ETSI


Values and selection criteria for test purpose TP103021Test purposes ACM Parameter values ALERTING Parameter


















































ETSI




ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM)/Test purpose: Ensure that the SUT in the state N3 on receipt of an ACM message where the CPS

indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way", theISDN access indicator is set to "ISDN" and the Transmission Medium Used (TMU) isincluded with the value TMU_VALUE and the Access Transport Parameter (ATP) is set toATP_VALUE.

sends a PROGRESS message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5);and with the BC encoded ISDN_BC_VALUE


SETUP; first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2PROGRESS; progress indicator : interworking has occurred and has resulted in atelecommunication service change (#5)BC : ISDN_BC_VALUE


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNTMU : TMU_VALUEATP: BC ATP_VALUE


ETSI


Values and selection criteria for test purpose TP103022Test purposes ACM Parameter values PROGRESS Parameter


















































ETSI




ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM).ISDN selection


criteria:support signalling procedures for connection type allowing fallback [A.13/10]

Test purpose: Ensure that the SUT in the state N2 on receipt of an ACM message where the CPSindicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and containing an Access Transport Parameter(ATP) including a High Layer Compatibility (HLC) and containing the progress indicator#5: "interworking has occurred and has resulted in a telecommunication service change"

sends a CALL PROCEEDING message with a progress indicator with the progressindication "interworking has occurred and has resulted in a telecommunication servicechange" (#5) and with the HLC.


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CALL PROCEEDING; progress indicator : interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)







Test purpose: Ensure that the SUT in the state N2 on receipt of an ACM message where the CPSindicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and containing an Access Transport Parameter(ATP) including a High Layer Compatibility (HLC) and containing the progress indicator#5: "interworking has occurred and has resulted in a telecommunication service change"

sends an ALERTING message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5)and with the HLC.


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)ALERTING; progress indicator : interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)


ETSI







Test purpose: Ensure that the SUT in the state N3 on receipt of an ACM message where the CPSindicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and containing an Access Transport Parameter(ATP) including a High Layer Compatibility (HLC) and containing the progress indicator#5: "interworking has occurred and has resulted in a telecommunication service change"

sends a PROGRESS message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5)and with the HLC.


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)PROGRESS; progress indicator : interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)







Test purpose: Ensure that the SUT in the state N3 on receipt of an ACM message where the CPSindicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and containing an Access Transport Parameter(ATP) including a High Layer Compatibility (HLC) and containing the progress indicator#5: "interworking has occurred and has resulted in a telecommunication service change"





ACM; CPS indicator: subscriber free,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)


ETSI




ETS 300 356-1 [5], clause 2.2TSS reference: DSS1-ISUP/Basic call/Receipt of the Address complete message (ACM)/ISDN selection



indicator is set to "no indication", with a cause parameter set to CV_ISUP and the OBCIwith the in-band information is set to "yes",

sends a DISCONNECT message with the progress indicator set to "in-bandinformation or appropriate pattern now available (#8)" and the cause information elementset to CV_ISDN


DISCONNECT; Cause information element: CV_ISDN (PIXIT)


ACM; CPS indicator: no indication,Cause parameter: CV_ISUP (PIXIT)OBCI in-band information: yes

Comments: ISUP ACM -> SUT -> DISCONNECT ISDN






indicator is set to "no indication", with a cause parameter set to CV_ISUP and the OBCIwith the in-band information is set to "yes",





ACM; CPS indicator: no indication,Cause parameter: CV_ISUP (PIXIT)OBCI in-band information: yes







indicator is set to "subscriber free", with a cause parameter set to CV_ISUP and theOBCI with the in-band information is set to "yes",





ACM; CPS indicator: subscriber free,Cause parameter: CV_ISUP (PIXIT)OBCI in-band information: yes


ETSI







indicator is set to "subscriber free", with a cause parameter set to CV_ISUP and theOBCI with the in-band information is set to "yes",





ACM; CPS indicator: subscriber free,Cause parameter: CV_ISUP (PIXIT)OBCI in-band information: yes


6.2.1.4 Receipt of the Call progress message (CPG)



ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Call progress message (CPG).ISDN selection


criteria:Test purpose: Ensure that the SUT in the state N3, having received the ACM message, on receipt of a

CPG message where the event information parameter event indicator is set to "Alerting"without BCI included,

sends an ALERTING message.ISDN Parameter

values:ALERTING;


CPG; event information parameter event indicator: Alerting







CPG message where the event information parameter event indicator is set to "Alerting"and the ATP containing the progress indicator PI_VALUE

sends an ALERTING message containing a progress indicator set to PI_VALUE.ISDN Parameter

values:ALERTING; progress indicator: PI_VALUE


CPG; event information parameter event indicator: Alerting


ETSI







CPG message where the event information parameter event indicator is set to"Progress" and no parameter is included,

sends no message.ISDN Parameter


values:CPG; event information parameter event indicator: Progress

Comments: ISUP CPG -> SUT ->






CPG message where the event information parameter event indicator is set to"Progress" and no parameter is included,



values:CPG; event information parameter event indicator: Progress






criteria:Test purpose: Ensure that the SUT in the state N4 on receipt of a CPG message where the event

information parameter event indicator is set to "Progress" and the ISUP indicator is setto ISUP_ID, the ISDN access indicator is set to ISDN_ACCES_ID and the OBCI with thein-band information set to OBCI_INBAND and having received the ACM message with thesame parameters,



values:ACM; ISUP indicator: ISUP_IDISDN access indicator: ISDN_ACCES_IDOBCI in-band information: OBCI_INBANDCPG; event information parameter event indicator: ProgressISUP indicator: ISUP_IDISDN access indicator: ISDN_ACCES_IDOBCI in-band information: OBCI_INBAND


ETSI


Values for test purpose TP104007Test purposes Parameter values

ISUP_ID ISDN_ACCESS_ID OBCI_INBANDVA_01 ISUP used all the way ISDN noVA_02 ISUP used all the way ISDN yesVA_03 ISUP used all the way non-ISDN noVA_04 ISUP used all the way non-ISDN yesVA_05 ISUP not used all the way - noVA_06 ISUP not used all the way - yes






CPG message where the event information parameter event indicator is set to "Alerting"the ISUP indicator parameter set to ISUP_ID, the ISDN access indicator set toISDN_ACCES_ID and the OBCI in-band information set to OBCI_INBAND (parametersdifferent from the previous ACM received)







ETSI



VA_01 CPGISUP_ID: ISUP not used all the wayACMISUP_ID: ISUP used all the way


VA_02 CPGISUP_ID: ISUP used all the wayISDN_ACCES_ID: non ISDNOBCI_INBAND: noACMISUP_ID: ISUP used all the wayISDN_ACCES_ID: ISDNOBCI_INBAND: no


VA_03 CPGISUP_ID: ISUP used all the wayISDN_ACCES_ID: non ISDNOBCI_INBAND: yesACMISUP_ID: ISUP used all the wayISDN_ACCES_ID: ISDNOBCI_INBAND: no


VA_04 CPG;ISUP_ID: ISUP used all the wayISDN access indicator: ISDNACM;ISUP_ID: ISUP used all the wayISDN access indicator: non-ISDN

PI_ID: Call has returned to the ISDN(#4)

VA_05 CPGISUP_ID: ISUP used all the wayISDN access indicator: ISDNOBCI_INBAND: yesACM;ISUP indicator: ISUP used all the wayISDN access indicator: ISDNOBCI_INBAND: no







CPG message where the event information parameter event indicator is set to"Progress" and the ISUP indicator parameter set to ISUP_ID, the ISDN access indicatorset to ISDN_ACCESS_ID and the OBCI in-band information set to OBCI_INBAND(parameters different from the previous ACM received)

sends a PROGRESS message with the progress indicator information element set toPI_ID.


PROGRESS; progress indicator: PI_ID


ACM; ISUP indicator: ACM_ISUP_IDISDN access indicator: ACM_ISDN_ACCESS_IDCPG; event information parameter event indicator: ProgressISUP indicator: CPG_ISUP_IDISDN access indicator: CPG_ISDN_ACCESS_ID

Comments: ISUP CPG -> SUT -> PROGRESS ISDN

ETSI







CPG message where the event information parameter event indicator is set to"Progress" and the ISUP indicator parameter set to ISUP_ID, the ISDN access indicatorset to ISDN_ACCESS_ID and the OBCI in-band information set to OBCI_INBAND(parameters different from the previous ACM received)





ACM; ISUP indicator: ACM_ISUP_IDISDN access indicator: ACM_ISDN_ACCESS_IDCPG; event information parameter event indicator: ProgressISUP indicator: CPG_ISUP_IDISDN access indicator: CPG_ISDN_ACCESS_ID


Values for test purposes TP104009, TP104010Test purposes ISUP Parameter values: ISDN Parameter values:

VA_01 CPGCPG_ISUP_ID: ISUP not used all the wayACMACM_ISUP_ID: ISUP used all the way


VA_02 CPGCPG_ISUP_ID: ISUP used all the wayCPG_ISDN_ACCES_ID: non ISDNACMACM_ISUP_ID: ISUP used all the wayACM_ISDN_ACCES_ID: ISDN

PI_ID: Destination address is non-ISDN (#2)

VA_03 CPG;CPG_ISUP_ID: ISUP used all the wayCPG_ISDN access indicator: ISDNACM;ACM_ISUP_ID: ISUP used all the wayACM_ISDN access indicator: non-ISDN

PI_ID: Call has returned to the ISDN (#4)

ETSI







CPG message where the event information parameter event indicator is set to "In-bandinformation or an appropriate pattern is now available", the ISUP indicator set toCPG_ISUP_ID and the ISDN access indicator set to CPG_ISDN_ACCESS_ID

sends a PROGRESS message with the progress indicator information element set toPI_VALUE.


PROGRESS; progress indicator: PI_VALUE


ACM;ISUP indicator: ACM_ISUP_IDISDN access indicator: ACM_ISDN_ACCES_IDCPG; event information parameter event indicator: In-band information or an appropriatepattern is now availableISUP indicator: CPG_ISUP_IDISDN access indicator: CPG_ISDN_ACCES_ID







CPG message where the event information parameter event indicator is set to "In-bandinformation or an appropriate pattern is now available", the ISUP indicator set toCPG_ISUP_ID and the ISDN access indicator set to CPG_ISDN_ACCESS_ID

sends a PROGRESS message with the progress indicator information element setPI_VALUE.


PROGRESS; progress indicator:PI_VALUE


ACM;ISUP indicator: ACM_ISUP_IDISDN access indicator: ACM_ISDN_ACCES_IDCPG; event information parameter event indicator: In-band information or an appropriatepattern is now availableISUP indicator: CPG_ISUP_IDISDN access indicator: CPG_ISDN_ACCESS_ID


ETSI


Values for test purposes TP104011, TP104012test purposes ISUP Parameter values: ISDN Parameter values:

VA_01 CPGCPG_ISUP_ID: ISUP used all the wayCPG_ISDN_ACCES_ID: ISDNACMACM_ISUP_ID: ISUP used all the wayACM_ISDN_ACCES_ID: ISDN


VA_02 CPGCPG_ISUP_ID: ISUP used all the wayCPG_ISDN_ACCES_ID: non-ISDNACMACM_ISUP_ID: ISUP used all the wayACM_ISDN_ACCES_ID: ISDN

PI_ID: In-band information orappropriate pattern now available (#8)and Destination address is non-ISDN(#2)

VA_03 CPGCPG_ISUP_ID: ISUP used all the wayCPG_ISDN_ACCES_ID: ISDNACMACM_ISUP_ID: ISUP used all the wayACM_ISDN_ACCES_ID: non-ISDN

PI_ID: In-band information orappropriate pattern now available (#8)and Call has returned to the ISDN (#4)

VA_04 CPGCPG_ISUP_ID: ISUP not used all the wayACMACM_ISUP_ID: ISUP used all the way

PI_ID: In-band information orappropriate pattern now available (#8)and Call is not end-to-end ISDN (#1)


ISUP reference:EN 300 899-1 [1], clauses 2.1.1.4.2, 2.1.1.3.2 table 11;

ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Call progress message (CPG).Test purpose: Ensure that the SUT in the state N3, having received the ACM message, on receipt of a

CPG message where the event information parameter event indicator is set to "Alerting" andthe Transmission medium requirement is included with the value "ISDN_BC_VALUE and theAccess Transport Parameter is set to ATP_VALUE.

sends an ALERTING message with the progress indicator information element set to"interworking has occurred and has resulted in a telecommunication service change" (#5) andthe BC encoded ISDN_BC_VALUE.


SETUP; first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2ALERTING; progress indicator: interworking has occurred and has resulted in atelecommunication service change (#5)BC: ISDN_BC_VALUE


CPG; event information parameter event indicator: AlertingTMU : TMU_VALUEATP: BC ATP_VALUE


ETSI





CPG message where the event information parameter event indicator is set to "Progress"and the Transmission medium requirement is included with the value "ISDN_BC_VALUEand the Access Transport Parameter is set to ATP_VALUE.

sends a PROGRESS message with the progress indicator information element set to"interworking has occurred and has resulted in a telecommunication service change" (#5) andthe BC encoded ISDN_BC_VALUE.


SETUP; first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2PROGRESS; progress indicator: interworking has occurred and has resulted in atelecommunication service change (#5)BC: ISDN_BC_VALUE


CPG; event information parameter event indicator: ProgressTMU : TMU_VALUEATP: BC: ATP_VALUE





CPG message where the event information parameter event indicator is set to "Progress"and the Transmission medium requirement is included with the value "ISDN_BC_VALUEand the Access Transport Parameter is set to ATP_VALUE.

sends a PROGRESS message with the progress indicator information element set to"interworking has occurred and has resulted in a telecommunication service change" (#5) andthe BC encoded ISDN_BC_VALUE.


SETUP; first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2PROGRESS; progress indicator: interworking has occurred and has resulted in atelecommunication service change (#5)BC: ISDN_BC_VALUE


CPG; event information parameter event indicator: ProgressTMU : TMU_VALUEATP: BC: ATP_VALUE


ETSI


Values and selection criteria for test purposes TP104013, TP104014, TP104015Test purposes ACM Parameter values ALERTING Parameter














3,1 kHz audio ([A.111/ISn.1.2.4]) AND unrestricted digital information with tones andannouncements ([A.111/ISn.1.2.5])




































ETSI



ISUP reference:EN 300 899-1 [1], clauses 2.1.1.4.2, 2.1.1.3.2 table 12 ;




CPG message where the event information parameter event indicator is set to "Alerting"and containing an Access Transport Parameter including a High Layer Compatibility (HLC)and containing the progress indicator #5: "interworking has occurred and has resulted in atelecommunication service change"





CPG; event information parameter event indicator: Alertingprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)







CPG message where the event information parameter event indicator is set to "Progress"and containing an Access Transport Parameter (ATP) including a High Layer Compatibility(HLC) and containing the progress indicator #5: "interworking has occurred and hasresulted in a telecommunication service change"

sends an PROGRESS message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5)and with the HLC.




CPG; event information parameter event indicator: Progressprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)


ETSI







CPG message where the event information parameter event indicator is set to "Progress"and containing an Access Transport Parameter (ATP) including a High Layer Compatibility(HLC) and containing the progress indicator #5: "interworking has occurred and hasresulted in a telecommunication service change"

sends an PROGRESS message with a progress indicator with the progress indication"interworking has occurred and has resulted in a telecommunication service change" (#5)and with the HLC.




CPG; event information parameter event indicator: Progressprogress indicator : interworking has occurred and has resulted in a telecommunicationservice change (#5)HLC: HLC_VALUE2 (PIXIT)







CPG message where the event information parameter event indicator is set to "in-bandinformation or an appropriate pattern is now available" with a cause parameter set toCV_ISUP,

sends a DISCONNECT message with the cause value set to CV_ISDN and theprogress indicator set to "In-band information or appropriate pattern now available (#8)".


DISCONNECT; Cause information element: CV_ISDN (PIXIT)Progress indicator: In-band information or appropriate pattern now available (#8)


CPG; event information parameter event indicator: in-band information or an appropriatepattern is now availableCause parameter: CV_ISUP (PIXIT)

Comments: ISUP CPG -> SUT -> DISCONNECT ISDN

ETSI







CPG message where the event information parameter event indicator is set to "in-bandinformation or an appropriate pattern is now available" with a cause parameter set toCV_ISUP,





CPG; event information parameter event indicator: in-band information or an appropriatepattern is now availableCause parameter: CV_ISUP (PIXIT)







CPG message where the event information parameter event indicator is set to"Progress" with a cause parameter set to CV_ISUP and the OBCI in-band information setto "Yes",





CPG; event information parameter event indicator: ProgressCause parameter: CV_ISUP (PIXIT)OBCI in-band information: Yes,







CPG message where the event information parameter event indicator is set to"Progress" with a cause parameter set to CV_ISUP and the OBCI in-band information setto "Yes",





CPG; event information parameter event indicator: ProgressCause parameter: CV_ISUP (PIXIT)OBCI in-band information: Yes


ETSI







CPG message where the event information parameter event indicator is set to"Progress", the ATP contains the progress indicator set to PI-VALUE, the ISUP indicatorparameter set to ISUP used all the way and the ISDN access indicator set to ISDN,





ACM; ISUP indicator: ISUP used all the wayISDN access indicator: ISDNCPG; event information parameter event indicator: ProgressISUP indicator: ISUP used all the wayISDN access indicator: ISDN


Values and additional selection criteria for test purpose TP104027VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)

6.2.1.5 Receipt of the Answer message (ANM)


ISUP reference:EN 300 899-1 [1], clause 2.1.1.5.;ETS 300 356-1 [5], clause 2.1.7

TSS reference: DSS1-ISUP/Basic call/Receipt of the Answer message (ANM).ISDN selection


criteria:Test purpose: Ensure that the SUT in the state N3, having received the ACM message, on receipt of an

ANM message sends a CONNECTISDN Parameter

values:CONNECT;


ANM;

Comments: ISUP ANM -> SUT -> CONNECT ISDN






ANM messagesends a CONNECT.


CONNECT;


ANM;


ETSI







ANM message containing a progress indicator set to PI_VALUE in the ATPsends a CONNECT included the progress indicator set to PI_VALUE.


CONNECT; progress indicator: PI_VALUE (PIXIT)


ANM; ATP progress indicator: PI_VALUE (PIXIT)







ANM message containing a progress indicator set to PI_VALUE in the ATPsends a CONNECT included the progress indicator set to PI_VALUE.







ISUP reference:EN 300 899-1 [1], clause 2.1.1.5 table 16.;

ETS 300 356-1 [5], clause 2.1.7TSS reference: DSS1-ISUP/Basic call/Receipt of the Answer message (ANM).ISDN selection



ANM message containing a Backward call indicator with the ISUP indicator set toISUP_IND and the ISDN access indicator set to ISDN_ACCESS_IND

sends a CONNECT included the progress indicator set to PI_VALUE.ISDN Parameter

values:CONNECT; progress indicator: PI_VALUE


ANM; ISUP indicator: ISUP_INDISDN access indicator: ISDN_ACCESS_IND


ETSI







ANM message containing a Backward call indicator with the ISUP indicator set toISUP_IND and the ISDN access indicator set to ISDN_ACCESS_IND

sends a CONNECT included the progress indicator set to PI_VALUE.ISDN Parameter

values:CONNECT; progress indicator: PI_VALUE


ANM; ISUP indicator: ISUP_INDISDN access indicator: ISDN_ACCESS_IND


Values for test purposes TP105005, TP105006Test purposes ISUP parameter values ISDN parameter values

VA_01 ANM;ISUP_IND: ISUP not used all theway

CONNECT;PI_VALUE: Call is not end-to-end: further progressinformation may be available in-band (#1)

VA_02 ANM;ISUP_IND: ISUP used all the wayISDN_ACCESS_IND: terminatingaccess non-ISDN

CONNECT;PI_VALUE: Destination address is non-ISDN (#2)






ANM message containing a Backward call indicator with the ISUP indicator set to "ISUPused all the way" and the ISDN access indicator set to "terminating access ISDN", havingpreviously received an ACM with the ISUP indicator set to "ISUP used all the way" and theISDN access indicator set to "terminating access non-ISDN"

sends a CONNECT included the progress indicator set to "Call has returned to theISDN (#4)".


CONNECT; progress indicator: Call has returned to the ISDN (#4)


ACM; ISUP indicator: ISUP used all the wayISDN access indicator: terminating access non-ISDNANM; ISUP indicator: ISUP used all the wayISDN access indicator: terminating access ISDN


ETSI







ANM message containing a Backward call indicator with the ISUP indicator set to "ISUPused all the way" and the ISDN access indicator set to "terminating access ISDN", havingpreviously received an ACM with the ISUP indicator set to "ISUP used all the way" and theISDN access indicator set to "terminating access non-ISDN"

sends a CONNECT included the progress indicator set to "Call has returned to theISDN (#4)".


CONNECT; progress indicator: Call has returned to the ISDN (#4)


ACM; ISUP indicator: ISUP used all the wayISDN access indicator: terminating access non-ISDNANM; ISUP indicator: ISUP used all the wayISDN access indicator: terminating access ISDN




ETS 300 356-1 [5], clause 2.1.7TSS reference: DSS1-ISUP/Basic call/Receipt of the Answer message (ANM).Test purpose: Ensure that the SUT in the state N3, having received the ACM message, on receipt of an

ANM message containing the Transmission Medium Used set to TMU_VALUE and the ATPwithout Bearer Capability (BC)

sends a CONNECT message with a progress indicator set to "interworking has occurredand has resulted in a telecommunication service change" (#5) and with the BC encodedISDN_BC_VALUE


SETUP: first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2CONNECT; progress indicator: interworking has occurred and has resulted in atelecommunication service change (#5)Bearer capability: ISDN_BC_VALUE


ANM; TMU: TMU_VALUEATP: no BC





ANM message containing the Transmission Medium Used set to TMU_VALUE and theATP without Bearer Capability (BC)

sends a CONNECT message with a progress indicator set to "interworking hasoccurred and has resulted in a telecommunication service change" (#5) and with the BCencoded ISDN_BC_VALUE




ANM; TMU: TMU_VALUEATP: no BC


ETSI


Values for test purposes TP105009, TP105010Test purposes ACM parameter

valuesCONNECT parameter

valuesSETUP parameter values

VA_01 TMU_VALUE:speech






support signalling procedures for connection type allowing fallback ([A.13/10]) AND 64 kbits/s

unrestricted preferred ([A.2/4]) AND speech ([A.2/1])

VA_02 TMU_VALUE:3,1 kHz audio







unrestricted preferred ([A.2/4]) AND 3,1 kHz audio ([A.2/2])




ANM message containing the Transmission Medium Used set to TMU_VALUE and theATP set to ATP_VALUE and containing the progress indicator set to "interworking hasoccurred and has resulted in a telecommunication service change" (#5)

sends a CONNECT message with the Bearer capability encoded ISDN_BC_VALUEand the progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)


SETUP: first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2CONNECT; Bearer capability: ISDN_BC_VALUEProgress indication: interworking has occurred and has resulted in a telecommunicationservice change(#5)


ANM; TMU: TMU_VALUEATP: ATP_VALUEProgress indication: interworking has occurred and has resulted in a telecommunicationservice change(#5)


ETSI





ANM message containing the Transmission Medium Used set to TMU_VALUE and theATP set to ATP_VALUE and containing the progress indicator set to "interworking hasoccurred and has resulted in a telecommunication service change" (#5)

sends a CONNECT message with the Bearer capability encoded ISDN_BC_VALUEand the progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)




ANM; TMU: TMU_VALUEATP: ATP_VALUEProgress indication: interworking has occurred and has resulted in a telecommunicationservice change(#5)





VA_01 TMU_VALUE:speechATP_VALUE:speech








VA_02 TMU_VALUE:speechATP_VALUE:3,1 kHz audio








VA_03 TMU_VALUE:3,1 kHz audioATP_VALUE:speech








VA_04 TMU_VALUE:3,1 kHz audioATP_VALUE:3,1 kHz audio








ETSI





criteria:unrestricted digital information with tones and announcements ([A.111/ISn.1.2.5])


support signalling procedures for connection type allowing fallback ([A.13/10]) AND64 kbits/s unrestricted preferred ([A.2/4])

Test purpose: Ensure that the SUT in the state N3, having received the ACM message, on receipt of anANM message containing the ATP including the Bearer Capability set to "unrestricted digitalinformation with tones/announcement" and without TMU parameter

sends a CONNECT message with the Bearer Capability set to "unrestricted digitalinformation with tones/announcement"


CONNECT; BC: unrestricted digital information with tones/announcement


ANM; ATP BC: unrestricted digital information with tones/announcementno TMU





criteria:unrestricted digital information with tones and announcements ([A.111/ISn.1.2.5])


support signalling procedures for connection type allowing fallback ([A.13/10]) AND64 kbits/s unrestricted preferred ([A.2/4])

Test purpose: Ensure that the SUT in the state N4, having received the ACM message, on receipt of anANM message containing the ATP including the Bearer Capability set to "unrestricteddigital information with tones/announcement" and without TMU parameter

sends a CONNECT message with the Bearer Capability set to "unrestricted digitalinformation with tones/announcement"




ANM; ATP BC: unrestricted digital information with tones/announcementno TMU







ANM message containing the HLC parameter in the ATP set to HLC_VALUEsends a CONNECT message HLC information element set to HLC_VALUE


CONNECT; HLC: HLC_VALUE (PIXIT)


ANM; ATP HLC: HLC_VALUE


ETSI







ANM message containing the HLC parameter in the ATP set to HLC_VALUEsends a CONNECT message HLC information element set to HLC_VALUE


CONNECT; HLC: HLC_VALUE (PIXIT)


ANM; ATP HLC: HLC_VALUE


P105017 ISDN reference:EN 300 403-1 [6], clause 5.1





Test purpose: Ensure that the SUT in the state N3, having received the ACM message, on receipt of anANM message containing the HLC parameter in the ATP with an HLC set to HLC_VALUEand the progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)

sends a CONNECT message with the HLC information element set to HLC_VALUE andthe progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CONNECT; HLC: HLC_VALUE2 (PIXIT)progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)


ANM; ATP HLC: HLC_VALUE2progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)







Test purpose: Ensure that the SUT in the state N4, having received the ACM message, on receipt of anANM message containing the HLC parameter in the ATP with an HLC set to HLC_VALUEand the progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)

sends a CONNECT message with the HLC information element set to HLC_VALUE andthe progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CONNECT; HLC: HLC_VALUE2 (PIXIT)progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)


ANM; ATP HLC: HLC_VALUE2progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)


ETSI







ANM message that does not contain any HLC parameter in the Access transport parametersends a CONNECT message without any the HLC information element


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CONNECT; no HLC


ANM; ATP: no HLC







ANM message that does not contain any HLC parameter in the Access transport parametersends a CONNECT message without any the HLC information element




ANM; ATP: no HLC







ANM message containing the LLC parameter in the ATP set to LLC_VALUEsends a CONNECT message LLC information element set to LLC_VALUE


CONNECT; LLC: LLC_VALUE (PIXIT)


ANM; ATP LLC: LLC_VALUE


ETSI







ANM message containing the LLC parameter in the ATP set to LLC_VALUEsends a CONNECT message LLC information element set to LLC_VALUE




ANM; ATP LLC: LLC_VALUE





ANM message containing the Transmission Medium Used set to TMU_VALUE and the ATPset to ATP_VALUE

sends a CONNECT message with the Bearer capability encoded ISDN_BC_VALUEISDN Parameter

values:SETUP: first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2CONNECT; Bearer capability: ISDN_BC_VALUE


ANM; TMU: TMU_VALUEATP: ATP_VALUE





ANM message containing the Transmission Medium Used set to TMU_VALUE and the ATPset to ATP_VALUE




ANM; TMU: TMU_VALUEATP: ATP_VALUE


ETSI





































6.2.1.6 Receipt of the Connect message (CON)



TSS reference: DSS1-ISUP/Basic call/Receipt of the Connect message (CON).ISDN selection


criteria:Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message with the Called Line

Status parameter set to "subscriber free" and the ISDN access indicator set to "ISDN"sends a CONNECT message.


CONNECT;


CON; Called Line Status: subscriber freeISDN access indicator: ISDN

Comments: ISUP CON -> SUT -> CONNECT ISDN

ETSI




TSS reference: DSS1-ISUP/Basic call/Receipt of the Connect message (CON)ISDN selection


criteria:use the overlap operation in the forward address signalling (sending) [A.3/2]

Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message with the Called LineStatus parameter set to "subscriber free" and the ISDN access indicator set to "ISDN"

sends a CONNECT message.ISDN Parameter

values:CONNECT;


CON; Called Line Status: subscriber freeISDN access indicator: ISDN






criteria:Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message with the ATP

containing a progress indicator set to ATC_PI_VALUEsends a CONNECT message with the progress indicator set to ATP_PI_VALUE.


CONNECT; progress indicator : ATP_PI_VALUE


CON; ATP progress indicator: ATP_PI_VALUE







Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message with the ATPcontaining a progress indicator set to ATC_PI_VALUE

sends a CONNECT message with the progress indicator set to ATP_PI_VALUE.ISDN Parameter

values:CONNECT; progress indicator : ATP_PI_VALUE


CON; ATP progress indicator: ATP_PI_VALUE


ETSI





criteria:unrestricted digital information with tones and announcements [A.111/ISn.1.2.5]


support signalling procedures for connection type allowing fallback [A.13/10]

Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message containing the ATPwith a Bearer Capability (BC) set to "unrestricted digital information withTones/Announcements"

sends a CONNECT message with the BC set to "unrestricted digital information withTones/Announcements".




CON; ATP: BC: unrestricted digital information with tones/announcementno TMU





criteria:unrestricted digital information with tones and announcements [A.111/ISn.1.2.5]


use the overlap operation in the forward address signalling (sending) [A.3/2] AND supportsignalling procedures for connection type allowing fallback [A.13/10]

Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing the ATPwith a Bearer Capability (BC) set to "unrestricted digital information withTones/Announcements"

sends a CONNECT message with the BC set to "unrestricted digital information withTones/Announcements".




CON; ATP BC: unrestricted digital information with tones/announcementno TMU




TSS reference: DSS1-ISUP/Basic call/Receipt of the Connect message (CON)ISUP selection


Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing theTransmission Medium Used set to TMU_VALUE and the ATP without Bearer Capability (BC)

sends a CONNECT message with a progress indicator set to "interworking has occurredand has resulted in a telecommunication service change" (#5) and with the BC encodedISDN_BC_VALUE




CON; TMU: TMU_VALUEATP: no BC


ETSI




TSS reference: DSS1-ISUP/Basic call/Receipt of the Connect message (CON)Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message containing the

Transmission Medium Used set to TMU_VALUE and the ATP without Bearer Capability(BC)

sends a CONNECT message with a progress indicator set to "interworking hasoccurred and has resulted in a telecommunication service change" (#5) and with the BCencoded ISDN_BC_VALUE




CON; TMU: TMU_VALUEATP: no BC





VA_01 TMU_VALUE:speech





Additional ISUPselectioncriteria:



VA_02 TMU_VALUE:3,1 kHz audio












Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing theTransmission Medium Used set to TMU_VALUE and the ATP set to ATP_VALUE




CON; TMU: TMU_VALUEATP: ATP_VALUE


ETSI





Transmission Medium Used set to TMU_VALUE and the ATP set to ATP_VALUEsends a CONNECT message with the Bearer capability encoded ISDN_BC_VALUE


SETUP: first Bearer Capability: SETUP_BC1second Bearer Capability: SETUP_BC2CONNECT; Bearer capability: ISDN_BC_VALUE


CON; TMU: TMU_VALUEATP: ATP_VALUE




























unrestricted preferred ([A.2/4]) AND speech ([A.2/1]) AND use the overlap operation in the

forward address signalling (sending) [A.3/2]








unrestricted preferred ([A.2/4]) AND 3,1 kHz audio ([A.2/2]) AND use the overlap operation in

the forward address signalling (sending) [A.3/2]

ETSI






Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing theTransmission Medium Used set to TMU_VALUE and the ATP set to ATP_VALUE andcontaining the progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)

sends a CONNECT message with the Bearer capability encoded ISDN_BC_VALUE andthe progress indication set to "interworking has occurred and has resulted in atelecommunication service change" (#5)




CON; TMU: TMU_VALUEATP: ATP_VALUEProgress indication: interworking has occurred and has resulted in a telecommunicationservice change(#5)





Transmission Medium Used set to TMU_VALUE and the ATP set to ATP_VALUE andcontaining the progress indicator set to "interworking has occurred and has resulted in atelecommunication service change" (#5)

sends a CONNECT message with the Bearer capability encoded ISDN_BC_VALUEand the progress indication set to "interworking has occurred and has resulted in atelecommunication service change" (#5)




CON; TMU: TMU_VALUEATP: ATP_VALUEProgress indication: interworking has occurred and has resulted in a telecommunicationservice change(#5)


ETSI






































ISUP reference:EN 300 899-1 [1], clauses 2.1.1.6, 2.1.1.5 table 18;

ETS 300 356-1 [5], clause 2.1.4TSS reference: DSS1-ISUP/Basic call/Receipt of the Connect message (CON)ISDN selection


criteria:Use the overlap operation in the forward address signalling (sending) [A.3/2]

Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing the ATPcontaining an HLC set to HLC_VALUE

sends a CONNECT message with the HLC set to HLC_VALUEISDN Parameter

values:CONNECT; HLC: HLC_VALUE


CON; ATP HLC: HLC_VALUE


ETSI






criteria:Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message containing the ATP

containing an HLC set to HLC_VALUEsends a CONNECT message with the HLC set to HLC_VALUE


CONNECT; HLC: HLC_VALUE


CON; ATP HLC: HLC_VALUE






criteria:use the overlap operation in the forward address signalling (sending) [A.3/2] AND supportsignalling procedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing the ATPcontaining an HLC set to HLC_VALUE and the progress indicator set to "interworking hasoccurred and has resulted in a telecommunication service change" (#5)

sends a CONNECT message with the HLC set to HLC_VALUE and the progressindicator set to "interworking has occurred and has resulted in a telecommunication servicechange" (#5)


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CONNECT; HLC: HLC_VALUE2progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)


CON; ATP HLC: HLC_VALUE2ATP progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)






criteria:support signalling procedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message containing the ATPcontaining an HLC set to HLC_VALUE and the progress indicator set to "interworking hasoccurred and has resulted in a telecommunication service change" (#5)

sends a CONNECT message with the HLC set to HLC_VALUE and the progressindicator set to "interworking has occurred and has resulted in a telecommunication servicechange" (#5)


SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CONNECT; HLC: HLC_VALUE2progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)


CON; ATP HLC: HLC_VALUE2ATP progress indicator: interworking has occurred and has resulted in a telecommunicationservice change (#5)


ETSI







Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message without ATP containing anHLC

sends a CONNECT message without the HLC information elementISDN Parameter

values:SETUP: HLC: HLC_VALUE1 (PIXIT), HLC_VALUE2 (PIXIT)CONNECT; no HLC


CON; ATP: no HLC



ISUP reference:EN 300 899-1 [1] clauses 2.1.1.6, 2.1.1.5 table 18;



criteria:Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message without ATP containing an

HLCsends a CONNECT message without the HLC information element




CON; ATP: no HLC







Test purpose: Ensure that the SUT in the state N2 on receipt of a CON message containing the ATPcontaining an LLC set to LLC_VALUE

sends a CONNECT message with the LLC set to LLC_VALUEISDN Parameter

values:CONNECT; LLC: LLC_VALUE


CON; ATP LLC: LLC_VALUE


ETSI






criteria:Test purpose: Ensure that the SUT in the state N3 on receipt of a CON message containing the ATP

containing an LLC set to LLC_VALUEsends a CONNECT message with the LLC set to LLC_VALUE


CONNECT; LLC: LLC_VALUE


CON; ATP LLC: LLC_VALUE


6.2.1.7 Receipt of the Release message (REL)

In some test purposes, PIXIT values are used for the ISUP indicator, the ISDN access indicator, the OBCI in-bandinformation and the ISDN progress indicator. The following table shows the possible values and the relations betweenthose PIXIT.

ISUP PIXIT values ISDN PIXIT valuesISUP_IND ISDN_ACCESS_IND OBCI In-band PI_VAL

ISUP is used all the way ISDN yes in-band information or appropriatepattern now available (#8)

ISUP is used all the way non-ISDN no destination address is non ISDN (#2)ISUP not used all the way - no Call is not end-to-end ISDN: further

progress information may be availablein-band (#1)

ISUP is used all the way non-ISDN yes destination address is non ISDN (#2)AND in-band information orappropriate pattern now available (#8)

ISUP not used all the way - yes Call is not end-to-end ISDN: furtherprogress information may be availablein-band (#1) AND in-band informationor appropriate pattern now available(#8)

If tones/announcement are applied, a DISCONNECT message shall contain a progress indicator #8. As an alternative, aPROGRESS message may be sent containing progress indicator #8.



ETS 300 356-1 [5], clause 2.2TSS reference: DSS1-ISUP/Basic call/Receipt of the Release message (REL)/ISDN selection


criteria:use the overlap operation in the forward address signalling ([A.3/2])

Test purpose: Ensure that the SUT in state N2, before having received an ACM message, on receipt ofa REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDNISDN Parameter

values:DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)

Comments: ISUP REL -> SUT -> DISCONNECT ISDN

ETSI






criteria:Test purpose: Ensure that the SUT in state N3, before having received an ACM message, on receipt of

a REL message with Cause value CV_ISUP, location LOC_ISUP,sends a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)








criteria:Test purpose: Ensure that the SUT in the state N2 after receiving the ACM message where the CPS

indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information is setto "no", and the REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a CALL PROCEEDING message followed by a DISCONNECT message withCause value CV_ISDN, location LOC_ISDN


CALL PROCEEDING;DISCONNECT; Cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noREL: Cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI_VAL and the REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a CALL PROCEEDING message with a progress indicator PI_VAL followed by aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN.


CALL PROCEEDING; progress indicator PI_VAL (PIXIT)DISCONNECT; Cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)REL: Cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the REL message with Cause valueCV_ISUP, location LOC_ISUP

sends an ALERTING message followed by a DISCONNECT message with Cause valueCV_ISDN, location LOC_ISDN.


ALERTING;DISCONNECT: Cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNREL: Cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND a and the OBCI in-band information set toOBCI and the REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a ALERTING message with a progress indicator set to PI_VAL followed by aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


ALERTING; progress indicator: PI_VAL (PIXIT)DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Alerting and aREL message with the Cause value CV_ISUP, location LOC_ISUP

sends a CALL PROCEEDING message followed by an ALERTING and aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


CALL PROCEEDING;ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: AlertingREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI






criteria:Test purpose: Ensure that the SUT in the state N2 after receiving the ACM message where the

CPS indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND and the OBCI with the in-bandinformation is set to OBCI followed by CPG message where the Event indicator is setto Alerting and a REL message with the Cause value CV_ISUP, location LOC_ISUP

sends a CALL PROCEEDING message with a progress indicator PI_VAL followedby an ALERTING and a DISCONNECT message with Cause value CV_ISDN, locationLOC_ISDN .


CALL PROCEEDING; progress indicator PI_VAL (PIXIT)ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: AlertingREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Progress and aREL message with the Cause value CV_ISUP, location LOC_ISUP

sends a CALL PROCEEDING message followed by a PROGRESS message and aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


CALL PROCEEDING;PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: ProgressISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI followed by CPG message where the Event indicator is set to Progress and a RELmessage with the Cause value CV_ISUP, location LOC_ISUP

sends a CALL PROCEEDING message with a progress indicator PI_VAL followed by aPROGRESS message and a DISCONNECT message with Cause value CV_ISDN,location LOC_ISDN .


CALL PROCEEDING; progress indicator PI_VAL (PIXIT)PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: ProgressISUP indicator: CPG_ISUP_IND (PIXIT)ISDN access indicator: CPG_ISDN_ACCESS_IND (PIXIT)OBCI in-band information: CPG_OBCI (PIXIT)REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to in-bandinformation or an appropriate pattern is now available and a REL message with the Causevalue CV_ISUP, location LOC_ISUP

sends a CALL PROCEEDING message followed by a PROGRESS message and aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


CALL PROCEEDING;PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: in-band information or an appropriate pattern is now availableISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI followed by CPG message where the Event indicator is set to in-band information oran appropriate pattern is now available and a REL message with the Cause valueCV_ISUP, location LOC_ISUP

sends a CALL PROCEEDING message with a progress indicator PI_VAL followed by aPROGRESS message and a DISCONNECT message with Cause value CV_ISDN,location LOC_ISDN .


CALL PROCEEDING; progress indicator PI_VAL (PIXIT)PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: in-band information or an appropriate pattern is now availableISUP indicator: CPG_ISUP_IND (PIXIT)ISDN access indicator: CPG_ISDN_ACCESS_IND (PIXIT)OBCI in-band information: CPG_OBCI (PIXIT)REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", and the REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDNISDN Parameter



ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI and the REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a PROGRESS message with a progress indicator set to PI_VALUE followed bya DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN.


PROGRESS; progress indicator: PI_VALUE (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)REL: cause value: CV_ISUP (PIXIT)Location: LOC_ISUP (PIXIT)







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the REL message with Cause valueCV_ISUP, location LOC_ISUP

sends an ALERTING message followed by a DISCONNECT message with Cause valueCV_ISDN, location LOC_ISDN.


ALERTING;DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information set to OBCIand the REL message with Cause value CV_ISUP, location LOC_ISUP,

sends a ALERTING message with a progress indicator set to PI_VAL followed by aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


ALERTING; progress indicator: PI_VAL (PIXIT)DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band: OBCI (PIXIT)REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)






criteria:Test purpose: Ensure that the SUT in the state N2 receiving the ACM message where the CPS

indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message and RELmessage with Cause value CV_ISUP, location LOC_ISUP

sends an ALERTING message followed by CONNECT and DISCONNECT message withCause value CV_ISDN, location LOC_ISDN


ALERTING;CONNECT;DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNANM;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information set to OBCIfollowed by an ANM message and REL message with Cause value CV_ISUP, locationLOC_ISUP,

sends a ALERTING message with a progress indicator set to PI_VAL followed by aCONNECT and DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


ALERTING; progress indicator: PI_VAL (PIXIT)CONNECT;DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCIANM;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)






criteria:Test purpose: Ensure that the SUT in state N2 after receiving the CON message and the REL

message with Cause value CV_ISUP, location LOC_ISUP,sends a CONNECT message followed by a DISCONNECT message with Cause value

CV_ISDN, location LOC_ISDN.ISDN Parameter

values:CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message and RELmessage with Cause value CV_ISUP, location LOC_ISUP

sends an ALERTING message followed by CONNECT and DISCONNECT message withCause value CV_ISDN, location LOC_ISDN


ALERTING;CONNECT;DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNANM;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information set to OBCIfollowed by an ANM message and REL message with Cause value CV_ISUP, locationLOC_ISUP,

sends a ALERTING message with a progress indicator s "destination address is non-ISDN (#2)" location "public network serving local user" followed by a CONNECT andDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


ALERTING; progress indicator: PI_VAL (PIXIT)CONNECT;DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCIANM;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI






criteria:Test purpose: Ensure that the SUT in state N10 after receiving the REL message with Cause value

CV_ISUP, location LOC_ISUP,sends a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN.


CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)



Comments:

6.2.1.8 Sending of the REL message

In some test purposes, PIXIT values are used for the ISUP indicator, the ISDN access indicator, the OBCI in-bandinformation and the ISDN progress indicator. The following table shows the possible values and the relations betweenthose PIXIT.

ISUP PIXIT values ISDN PIXIT valuesISUP_IND ISDN_ACCESS_IND OBCI In-band PI_VAL

ISUP is used all the way ISDN yes in-band information or appropriatepattern now available (#8)

ISUP is used all the way non-ISDN no destination address is non ISDN (#2)ISUP not used all the way - no Call is not end-to-end ISDN: further

progress information may be availablein-band (#1)

ISUP is used all the way non-ISDN yes destination address is non ISDN (#2)AND in-band information orappropriate pattern now available (#8)

ISUP not used all the way - yes Call is not end-to-end ISDN: furtherprogress information may be availablein-band (#1) AND in-band informationor appropriate pattern now available(#8)

TP108011 ISDN reference:EN 300 403-1 [6], clauses 5.3 and 5.8.3


ETS 300 356-1 [5], clause 2.2TSS reference: DSS1-ISUP/Basic call/Sending of the Release message (REL)/ISDN selection


criteria:use the overlap operation in the forward address signalling ([A.3/2]

Test purpose: Ensure that the SUT in state N2 before having received an ACM message, on receiptof a message RELEASE COMPLETE with Cause value CV_ISDN, location LOC_ISDN,

sends a REL message with Cause value CV_ISUP, location LOC_ISUPISDN Parameter

values:RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)

Comments: ISDN RELEASE COMPLETE -> SUT -> REL ISUP

ETSI







Test purpose: Ensure that the SUT in state N2 before having received an ACM message, on receiptof a message RELEASE with Cause value CV_ISDN, location LOC_ISDN,


values:RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)



Comments: ISDN RELEASE -> SUT -> REL ISUP






Test purpose: Ensure that the SUT in state N2 before having received an ACM message, on receiptof a message DISCONNECT with Cause value CV_ISDN, location LOC_ISDN,





Comments: ISDN DISCONNECT -> SUT -> REL ISUP





criteria:Test purpose: Ensure that the SUT in state N3 before having received an ACM message, on receipt

of a message RELEASE COMPLETE with Cause value CV_ISDN, location LOC_ISDN,sends a REL message with Cause value CV_ISUP, location LOC_ISUP


RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







of a message RELEASE with Cause value CV_ISDN, location LOC_ISDN,sends a REL message with Cause value CV_ISUP, location LOC_ISUP


RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









of a message DISCONNECT with Cause value CV_ISDN, location LOC_ISDN,sends a REL message with Cause value CV_ISUP, location LOC_ISUP











indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", sends out a CALL PROCEEDING message and on receipt of a RELEASECOMPLETE message with Cause value CV_ISDN, location LOC_ISDN,


values:CALL PROCEEDING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI








sends out a CALL PROCEEDING message and on receipt of a RELEASE messagewith Cause value CV_ISDN, location LOC_ISDN,


values:CALL PROCEEDING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)










sends out a CALL PROCEEDING message and on receipt of a DISCONNECTmessage with Cause value CV_ISDN, location LOC_ISDN,


values:CALL PROCEEDING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI sends out a CALL PROCEEDING message with a progress indicator PI_VAL andon receipt of the RELEASE COMPLETE message with Cause value CV_ISDN, locationLOC_ISDN,


values:CALL PROCEEDING; progress indicator PI_VAL (PIXIT)RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI sends out a CALL PROCEEDING message with a progress indicator PI_VAL andon receipt of the RELEASE message with Cause value CV_ISDN, location LOC_ISDN,


values:CALL PROCEEDING; progress indicator PI_VAL (PIXIT)RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI sends out a CALL PROCEEDING message with a progress indicator PI_VAL andon receipt of the DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN,


values:CALL PROCEEDING; progress indicator PI_VAL (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)






ETS 300 356-1 [5],clause 2.2TSS reference: DSS1-ISUP/Basic call/Sending of the Release message (REL)/ISDN selection



indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" sends out an ALERTING message and onreceipt of a RELEASE COMPLETE message with Cause value CV_ISDN, locationLOC_ISDN

sends a REL message with Cause value CV_ISUP, location LOC_ISUP.ISDN Parameter

values:ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" sends out an ALERTING message and onreceipt of a RELEASE message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" sends out an ALERTING message and onreceipt of a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND sends out a ALERTING message with aprogress indicator set to PI_VAL and on receipt of a RELEASE COMPLETE messagewith Cause value CV_ISDN, location LOC_ISDN,


values:ALERTING; progress indicator: PI_VAL (PIXIT)RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND sends out a ALERTING message with aprogress indicator set to PI_VAL and on receipt of a RELEASE message with Causevalue CV_ISDN, location LOC_ISDN,


values:ALERTING; progress indicator: PI_VAL (PIXIT)RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND sends out a ALERTING message with aprogress indicator set to PI_VAL and on receipt of a DISCONNECT message with Causevalue CV_ISDN, location LOC_ISDN,


values:ALERTING; progress indicator: PI_VAL (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Alerting sendsout a CALL PROCEEDING message followed by an ALERTING and on receipt of aRELEASE COMPLETE message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: AlertingREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Alerting sendsout a CALL PROCEEDING message followed by an ALERTING and on receipt of aRELEASE message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Alerting sendsout a CALL PROCEEDING message followed by an ALERTING and on receipt of aDISCONNECT message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "Yes" followed by CPG message where the Event indicator is set to ALeRTIngsends out a CALL PROCEEDING message with a progress indicator "in-bandinformation or appropriate pattern now available (#8)" location "public network serving localuser" followed by an ALERTING and on receipt of a RELEASE COMPLETE message withthe Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator "in-band information or appropriate pattern nowavailable (#8)" location "public network serving local user"ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: YesCPG; Event indicator: ALeRTIngREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "Yes" followed by CPG message where the Event indicator is set to ALeRTIngsends out a CALL PROCEEDING message with a progress indicator "in-bandinformation or appropriate pattern now available (#8)" location "public network serving localuser" followed by an ALERTING and on receipt of a RELEASE message with the Causevalue CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator "in-band information or appropriate pattern nowavailable (#8)" location "public network serving local user"ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "Yes" followed by CPG message where the Event indicator is set to ALeRTIngsends out a CALL PROCEEDING message with a progress indicator "in-band informationor appropriate pattern now available (#8)" location "public network serving local user"followed by an ALERTING and on receipt of a DISCONNECT message with the Causevalue CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator "in-band information or appropriate pattern nowavailable (#8)" location "public network serving local user"ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Progress sendsout a CALL PROCEEDING message followed by a PROGRESS message and on receiptof a RELEASE COMPLETE message with the Cause value CV_ISDN, locationLOC_ISDN


values:CALL PROCEEDING;PROGRESS;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: ProgressISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Progress sendsout a CALL PROCEEDING message followed by a PROGRESS message and on receiptof a RELEASE message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;PROGRESS;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Progress sendsout a CALL PROCEEDING message followed by a PROGRESS message and on receiptof a DISCONNECT message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND and the OBCI with the in-bandinformation is set to OBCI followed by CPG message where the Event indicator is set toPRoGREss sends out a CALL PROCEEDING message with a progress indicatorPI_VAL followed by a PROGRESS message and on receipt of a RELEASE COMPLETEmessage with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator PI_VAL (PIXIT)PROGRESS;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: PRoGREssISUP indicator: CPG_ISUP_IND (PIXIT)ISDN access indicator: CPG_ISDN_ACCESS_IND (PIXIT)OBCI in-band information: CPG_OBCI (PIXIT)REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI followed by CPG message where the Event indicator is set to Progress sends out aCALL PROCEEDING message with a progress indicator PI_VAL followed by aPROGRESS message and on receipt of a RELEASE message with the Cause valueCV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator PI_VAL (PIXIT)PROGRESS;RELEASE ; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: ProgressISUP indicator: CPG_ISUP_IND (PIXIT)ISDN access indicator: CPG_ISDN_ACCESS_IND (PIXIT)OBCI in-band information: CPG_OBCI (PIXIT)REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND and the OBCI with the in-bandinformation is set to OBCI followed by CPG message where the Event indicator is set toPRoGREss sends out a CALL PROCEEDING message with a progress indicatorPI_VAL followed by a PROGRESS message and on receipt of a DISCONNECT messagewith the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator PI_VAL (PIXIT)PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: PRoGREssISUP indicator: CPG_ISUP_IND (PIXIT)ISDN access indicator: CPG_ISDN_ACCESS_IND (PIXIT)OBCI in-band information: CPG_OBCI (PIXIT)REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


TP108061 ISDN reference:EN 300 403-1 [6], clause 5


ETS 300 356-1 [5], clause 2TSS reference: DSS1-ISUP/Basic call/Sending of the Release message (REL)/ISDN selection



indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to "in-bandinformation or an appropriate pattern is now available" sends out a CALL PROCEEDINGmessage followed by a PROGRESS message and a RELEASE COMPLETE messagewith the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;PROGRESS ;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: in-band information or an appropriate pattern is now availableREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to "in-bandinformation or an appropriate pattern is now available" sends out a CALL PROCEEDINGmessage followed by a PROGRESS message and a RELEASE message with the Causevalue CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;PROGRESS ;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to "in-bandinformation or an appropriate pattern is now available" sends out a CALL PROCEEDINGmessage followed by a PROGRESS message and a DISCONNECT message with theCause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING;PROGRESS ;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI followed by CPG message where the Event indicator is set to "in-band informationor an appropriate pattern is now available" sends out a CALL PROCEEDING message witha progress indicator set to PI_VAL followed by a PROGRESS message and on receipt ofa RELEASE COMPLETE message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator: PI_VAL (PIXIT)PROGRESS;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)CPG; Event indicator: in-band information or an appropriate pattern is now availableREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI followed by CPG message where the Event indicator is set to "in-band informationor an appropriate pattern is now available" sends out a CALL PROCEEDING message witha progress indicator set to PI_VAL followed by a PROGRESS message and on receipt ofa RELEASE message with the Cause value CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator: PI_VAL (PIXIT)PROGRESS;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CPS indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND and the OBCI with the in-bandinformation is set to OBCI followed by CPG message where the Event indicator is setto "in-band information or an appropriate pattern is now available" sends out a CALLPROCEEDING message with a progress indicator set to PI_VAL followed by aPROGRESS message and on receipt of a DISCONNECT message with the Causevalue CV_ISDN, location LOC_ISDN


values:CALL PROCEEDING; progress indicator: PI_VAL (PIXIT)PROGRESS;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", and on receipt of a RELEASE COMPLETE message with Cause valueCV_ISDN, location LOC_ISDN






ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", and on receipt of a RELEASE message with Cause value CV_ISDN, locationLOC_ISDN











indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", and on receipt of a DISCONNECT message with Cause value CV_ISDN,location LOC_ISDN






ETSI







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI

sends out a PROGRESS message with a progress indicator PI_VALUE and onreceipt of a RELEASE COMPLETE message with Cause value CV_ISDN, locationLOC_ISDN


values:PROGRESS; progress indicator PI_VALUE (PIXIT)RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_INDOBCI in-band information: OBCI (PIXIT)REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)








sends out a PROGRESS message with a progress indicator PI_VALUE and onreceipt of a RELEASE message with Cause value CV_ISDN, location LOC_ISDN


values:PROGRESS; progress indicator PI_VALUE (PIXIT)RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI








sends out a PROGRESS message with a progress indicator PI_VALUE and onreceipt of a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


values:PROGRESS; progress indicator PI_VALUE (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" sends out an ALERTING message and onreceipt of a RELEASE COMPLETE message with Cause value CV_ISDN, locationLOC_ISDN


values:ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" sends out an ALERTING message and onreceipt of a RELEASE message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" sends out an ALERTING message and onreceipt of a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information is set toOBCI, sends out an ALERTING message with a progress indicator set to PI_VAL and onreceipt of a RELEASE COMPLETE message with Cause value CV_ISDN, locationLOC_ISDN


values:ALERTING; progress Indicator: PI_VAL (PIXIT)RELEASE COMPLETE: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCIREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information is set toOBCI, sends out an ALERTING message with a progress indicator set to PI_VAL and onreceipt of a RELEASE message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING; progress Indicator: PI_VAL (PIXIT)RELEASE: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information is set toOBCI, sends out an ALERTING message with a progress indicator set to PI_VAL and onreceipt of a DISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING; progress Indicator: PI_VAL (PIXIT)DISCONNECT: cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message, locationLOC_ISDN sends out an ALERTING message followed by CONNECT and on receipt of aRELEASE COMPLETE message with Cause value CV_ISDN


values:ALERTING;CONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNANM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message, locationLOC_ISDN sends out an ALERTING message followed by CONNECT and on receipt of aRELEASE message with Cause value CV_ISDN


values:ALERTING;CONNECT;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message, locationLOC_ISDN sends out an ALERTING message followed by CONNECT and on receipt of aDISCONNECT message with Cause value CV_ISDN


values:ALERTING;CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND followed by an ANM message sends out aALERTING message with a progress indicator set to PI_VAL followed by a CONNECTand on receipt of a RELEASE COMPLETE message with Cause value CV_ISDN, locationLOC_ISDN


values:ALERTING; progress Indicator: PI_VAL (PIXIT)CONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)ANM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND followed by an ANM message sends out aALERTING message with a progress indicator set to PI_VAL followed by a CONNECTand on receipt of a RELEASE message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING; progress Indicator: PI_VAL (PIXIT)CONNECT;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND followed by an ANM message sends out aALERTING message with a progress indicator set to PI_VAL followed by a CONNECTand on receipt of a DISCONNECT message with Cause value CV_ISDN, locationLOC_ISDN


values:ALERTING; progress Indicator: PI_VAL (PIXIT)CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)








criteria:Test purpose: Ensure that the SUT in state N2 after receiving the CON message sends out a

CONNECT message and on receipt of a RELEASE COMPLETE message with Causevalue CV_ISDN, location LOC_ISDN


values:CONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)



Comments:






CONNECT message and on receipt of a RELEASE message with Cause value CV_ISDN,location LOC_ISDN


values:CONNECT;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CONNECT message and on receipt of a DISCONNECT message with Cause valueCV_ISDN, location LOC_ISDN


values:CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message sends out anALERTING message followed by CONNECT message and on receipt of a RELEASECOMPLETE message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;CONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)



Comments:

ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message sends out anALERTING message followed by CONNECT message and on receipt of a RELEASEmessage with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;CONNECT;RELEASE ; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message sends out anALERTING message followed by CONNECT message and on receipt of a DISCONNECTmessage with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING;CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information set toOBCI followed by an ANM message sends out an ALERTING message with a progressindicator set to PI_VAL followed by a CONNECT message and on receipt of a RELEASECOMPLETE message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING; progress indicator: destination address is non-ISDN (#2) location publicnetwork serving local userCONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: subscriber free,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)ANM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)

Comments:






indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information set toOBCI followed by an ANM message sends out an ALERTING message with a progressindicator set to PI_VAL followed by a CONNECT message and on receipt of a RELEASEmessage with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING; progress indicator: destination address is non-ISDN (#2) location publicnetwork serving local userCONNECT;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







indicator is set to "subscriber free", the ISUP indicator is set to ISUP_IND, the ISDNaccess indicator is set to ISDN_ACCESS_IND, the OBCI in-band information set toOBCI followed by an ANM message sends out an ALERTING message with a progressindicator set to PI_VAL followed by a CONNECT message and on receipt of aDISCONNECT message with Cause value CV_ISDN, location LOC_ISDN


values:ALERTING; progress indicator: destination address is non-ISDN (#2) location publicnetwork serving local userCONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)








criteria:Test purpose: Ensure that the SUT in state N3 on receipt of a CON message followed by a RELEASE

COMPLETE message with Cause value CV_ISDN, location LOC_ISDNsends a REL message with Cause value CV_ISUP, location LOC_ISUP.


RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


CON;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)

Comments:





criteria:Test purpose: Ensure that the SUT in state N3 on receipt of a CON message followed by a RELEASE

message with Cause value CV_ISDN, location LOC_ISDNsends a REL message with Cause value CV_ISUP, location LOC_ISUP.


RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI






criteria:Test purpose: Ensure that the SUT in state N3 on receipt of a CON message followed by a

DISCONNECT message with Cause value CV_ISDN, location LOC_ISDNsends a REL message with Cause value CV_ISUP, location LOC_ISUP.






6.2.1.9 Receipt of Reset circuit message (RSC), Circuit group reset message (GRS)or Circuit group blocking message (CGB) with the indication hardware failureoriented

6.2.1.9.1 Receipt of Reset Circuit message (RSC)



TSS reference: DSS1-ISUP/Basic call/Receipt of Reset circuit message (RSC), Circuit group reset message(GRS) or Circuit group blocking message (CGB) with the indication hardware failure oriented



Test purpose: Ensure that the SUT in state N3, having received the ACM message, on receipt of a RSCmessage,

sends the DISCONNECT message with the cause value set to "normal, unspecified (31)"ISDN Parameter

values:DISCONNECT; cause value: normal unspecified (31)


RSC

Comments: ISUP RSC -> SUT -> DISCONNECT ISDN






Test purpose: Ensure that the SUT in state N4 having received the ACM message, on receipt of a RSCmessage,


values:DISCONNECT; cause value: normal, unspecified (31)


RSC


ETSI







Test purpose: Ensure that the SUT in state N10, on receipt of a RSC message,sends the DISCONNECT message with the cause value set to "normal, unspecified (31)"


DISCONNECT; cause value: normal, unspecified (31)


RSC







Test purpose: Ensure that the SUT in state N2, on receipt of a RSC message,does not send the DISCONNECT message


no DISCONNECT


RSC







Test purpose: Ensure that the SUT in Idle state, on receipt of a RSC message,does not send the DISCONNECT message


no DISCONNECT


RSC


ETSI


6.2.1.9.2 Receipt of Circuit Group Reset message (GRS)






Test purpose: Ensure that the SUT in state N3, having received the ACM message, on receipt of a GRSmessage ,




GRS;

Comments: ISUP GRS -> SUT -> DISCONNECT ISDN






Test purpose: Ensure that the SUT in state N4, having received the ACM message, on receipt of a GRSmessage,




GRS;







Test purpose: Ensure that the SUT in state N10, on receipt of a GRS message,sends the DISCONNECT message with the cause value set to "normal, unspecified (31)"




GRS;


ETSI







Test purpose: Ensure that the SUT in state N2, on receipt of a GRS message,does not send the DISCONNECT message


no DISCONNECT


GRS;







Test purpose: Ensure that the SUT in Idle state, on receipt of a GRS message,does not send the DISCONNECT message


no DISCONNECT


GRS;


6.2.1.9.3 Receipt of Circuit Group blocking message (CGB) with the indication "hardwarefailure oriented"


ISUP reference:EN 300 899-1 [1], clause 2.1.1.9;ETS 300 356-1 [5], clause 2.8.2.2




Test purpose: Ensure that the SUT in state N3, having received the ACM message, on receipt of a CGBmessage with the Circuit group supervision message type set to "hardware failureoriented",




CGB; Circuit group supervision message type: hardware failure oriented

Comments: ISUP CGB -> SUT -> DISCONNECT ISDN

ETSI







Test purpose: Ensure that the SUT in state N4, having received the ACM message, on receipt of a CGBmessage with the Circuit group supervision message type set to "hardware failureoriented",











Test purpose: Ensure that the SUT in state N10, on receipt of a CGB message with the Circuit groupsupervision message type set to "hardware failure oriented",












does not send the DISCONNECT messageISDN Parameter

values:no DISCONNECT



Comments: ISUP CGB -> SUT ->

ETSI







Test purpose: Ensure that the SUT in Idle state, on receipt of a CGB message with the Circuit groupsupervision message type set to "hardware failure oriented",






6.2.1.10 DSS1 Data link reset and Data Link failure procedures



ETS 300 356-1 [5], clause 2.2TSS reference: DSS1-ISUP/Basic call/DSS1 Data link reset and Data Link failure proceduresISDN selection


criteria:Test purpose: Ensure that the SUT in state N2, on receipt of a data link reset primitive (DL-ESTABLISH-

INDICATION)sends a DISCONNECT message with the cause value set to "temporary failure (41)" and

sends a REL message with the cause value set to "temporary failure (41)";ISDN Parameter

values:DISCONNECT; cause value: temporary failure (41)


REL; cause value: temporary failure (41)

Comments: ISDN DL-ESTABLISH IND -> SUT -> REL ISUP -> DISCONNECT ISDN






INDICATION)does not send a DISCONNECT message and REL message



Comments: ISDN DL-ESTABLISH IND -> SUT ->

ETSI
























criteria:Test purpose: Ensure that the SUT in state N2, on receipt of a data link failure primitive (DL-RELEASE)

sends a REL message with the cause value set to "destination out of order (27)" and doesnot send any DISCONNECT message but release the call internally.


DL-RELEASE


REL; cause value: destination out of order (27)

Comments: ISDN DL-RELEASE -> SUT -> REL ISUP

ETSI



















DL-RELEASE








criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a data link failure primitive (DL-RELEASE),

sends DL-ESTABLISH INDICATION primitive, after expire of timer T309 without data link re-establishment



DL-RELEASEDL-ESTABLISH IND;




ETSI


6.2.1.11 Receipt of the Suspend message (SUS) network initiated



ETS 300 356-1 [5], clause 2.4.1TSS reference: DSS1-ISUP/Basic call/DSS1 Data link reset and Data Link failure proceduresISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a SUSPEND message with the suspend

indicator set to "network initiated"does not send any message.



SUS; Suspend indicator: network initiated

Comments: ISUP SUS -> SUT ->

6.2.1.12 Receipt of the Resume message (RES) network initiated



ETS 300 356-1 [5], clause 2.4.1TSS reference: DSS1-ISUP/Basic call/DSS1 Data link reset and Data Link failure proceduresISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a SUSPEND message followed by the

RES message both containing the suspend/resume indicator set to "network initiated"does not send any message.



SUS; Suspend indicator: network initiatedRES; Resume indicator: network initiated

Comments: ISUP RES -> SUT ->

6.2.1.13 Release by the exchange



ETS 300 356-1 [5], clause 2.4.3TSS reference: DSS1-ISUP/Basic call/Release by the exchange/ISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, having received a SUSPEND message containing the

suspend/resume indicator set to "network initiated", at expire of timer T6,sends a REL message with the cause parameter set to "recovery on timer expire (102)"

and a DISCONNECT message with the cause information element set to "normal callclearing (16)".


DISCONNECT; Cause information element: normal call clearing (16)


SUS; Suspend indicator: network initiatedREL; Cause parameter: recovery on timer expire (102)

Comments: SUT -> REL ISUP + RELEASE ISDN

ETSI


6.2.1.14 Receipt of the release complete (RLC)


ISUP reference:ETS 300 356-1 [5], clause 2.9.5.1

TSS reference: DSS1-ISUP/Basic call/Receipt of the release complete (RLC)/ISDN selection


criteria:use the overlap operation in the forward address signalling ([A.3/2])

Test purpose: Ensure that the SUT in state N2, before having received an ACM message, on receiptof a RLC message,

sends a DISCONNECT message and a REL messageISDN Parameter

values:DISCONNECT;


RLC;REL;

Comments: ISUP RLC -> SUT -> DISCONNECT ISDN + REL ISUP





criteria:Test purpose: Ensure that the SUT in state N3, before having received an ACM message, on receipt

of a RLC message,sends a DISCONNECT and a REL message


DISCONNECT;


RLC;REL;







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", and the RLC message,

sends a CALL PROCEEDING message followed by a DISCONNECT and a RELmessage


CALL PROCEEDING;DISCONNECT;


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noRLC;REL;


ETSI







CPS indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used allthe way", the ISDN access indicator is set to "ISDN" and the RLC message,

sends an ALERTING message followed by a DISCONNECT and a REL message.ISDN Parameter

values:ALERTING;DISCONNECT;


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNRLCREL;







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Alerting and aRLC message

sends a CALL PROCEEDING message followed by an ALERTING and aDISCONNECT and a REL message


CALL PROCEEDING;ALERTING;DISCONNECT;


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: AlertingRLC;REL;


ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to Progress and aRLC message

sends a CALL PROCEEDING message followed by a PROGRESS message and aDISCONNECT and a REL message.


CALL PROCEEDING;PROGRESS;DISCONNECT;


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: ProgressISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNRLC;REL;







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", followed by CPG message where the Event indicator is set to in-bandinformation or an appropriate pattern is now available and a RLC message

sends a CALL PROCEEDING message followed by a PROGRESS message and aDISCONNECT and REL message.


CALL PROCEEDING;PROGRESS;DISCONNECT;


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noCPG; Event indicator: in-band information or an appropriate pattern is now availableISUP indicator: ISUP is used all the wayISDN access indicator: non-ISDNRLC;REL;


ETSI







indicator is set to "no indication", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the OBCI with the in-band information isset to "no", and the RLC message,

sends a DISCONNECT and a REL.ISDN Parameter

values:DISCONNECT;


ACM; CPS indicator: no indication,ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNOBCI in-band information: noRLC;REL;







indicator is set to "no indication", the ISUP indicator is set to ISUP_IND, the ISDN accessindicator is set to ISDN_ACCESS_IND and the OBCI with the in-band information is set toOBCI and the RLC message,

sends a PROGRESS message with a progress indicator set to PI_VALUE followed by aDISCONNECT and a REL message.


PROGRESS; progress indicator: PI_VALUE (PIXIT)DISCONNECT;


ACM; CPS indicator: no indication,ISUP indicator: ISUP_IND (PIXIT)ISDN access indicator: ISDN_ACCESS_IND (PIXIT)OBCI in-band information: OBCI (PIXIT)RLC;REL;







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" and the RLC message

sends an ALERTING message followed by a DISCONNECT and a REL message.ISDN Parameter

values:ALERTING;DISCONNECT


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNRLC;REL;


ETSI







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message and RLC message

sends an ALERTING message followed by CONNECT and DISCONNECT and a RELmessage


ALERTING;CONNECT;DISCONNECT


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNANM;RLC;REL;






criteria:Test purpose: Ensure that the SUT in state N2 after receiving the CON message and the RLC

message,sends a CONNECT message followed by a DISCONNECT and a REL message.


CONNECT;DISCONNECT;


RLC;REL;







indicator is set to "subscriber free", the ISUP indicator is set to "ISUP is used all the way",the ISDN access indicator is set to "ISDN" followed by an ANM message and RLC message

sends an ALERTING message followed by CONNECT and DISCONNECT and a RELmessage


ALERTING;CONNECT;DISCONNECT


ACM; CPS indicator: subscriber freeISUP indicator: ISUP is used all the way,ISDN access indicator: ISDNANM;RLC;REL;


ETSI


6.2.2 Interworking from Non-ISDN to ISUP (Outgoing Call)

6.2.2.1 Sending of the Initial address message (IAM)

TP201001 ISUP reference:EN 300 899-1 [1], clause 2.2.1.1

TSS reference: NON ISDN-ISUP/Basic call/Sending of the Initial address message (IAM)/ISUP selection

criteria:Test purpose: Ensure that the SUT on receipt of the Address signals

sends an IAM message, with the TMR set to "3,1 kHz audio" and the FCI encoded asfollowed:National/international call indicator: "call to be treated as a national call"Interworking indicator: "no interworking encountered (No7 signalling all the way)"ISUP indicator: "ISUP used all the way"ISDN access indicator: "originating access non-ISDN"


IAM; TMR: 3,1 kHz audioFCI National/international call indicator: call to be treated as a national callFCI Interworking indicator: no interworking encountered (No7 signalling all the way)FCI ISUP indicator: ISUP used all the wayFCI ISDN access indicator: originating access non-ISDN

Comments:

6.2.2.2 Receipt of the Address complete message (ACM)


TSS reference: NON ISDN-ISUP/Basic call/Receipt of the Address complete message (ACM)/ISUP selection

criteria:Test purpose: Ensure that the SUT on receipt of the ACM message

does not send any message on the non-ISDN side.ISUP Parameter

values:IAM;ACM;

Comments:

6.2.2.3 Receipt of the Call progress message (CPG)


TSS reference: NON ISDN-ISUP/Basic call/Receipt of the Call progress message (CPG)/ISUP selection

criteria:Test purpose: Ensure that the SUT on receipt of the CPG message


values:IAM;ACM;CPG;

Comments:

ETSI


6.2.2.4 Sending of the Release Message (REL)


TSS reference: NON ISDN-ISUP/Basic call/Sending of the Release Message (REL)/ISUP selection

criteria:Test purpose: Ensure that the SUT, having sent the IAM message, on receipt of the message

indicating the release proceduresends the REL message with the cause indicator coded to No 16.


IAM;REL; cause indicator: No. 16

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the SAM message, on receipt of the message



SAM;REL; cause indicator: No. 16

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the ACM message, on receipt of the message



ACM;REL; cause indicator: No. 16

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the CPG message, on receipt of the message



CPG;REL; cause indicator: No. 16

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the ANM message, on receipt of the message



ANM;REL; cause indicator: No. 16

Comments:

ETSI




criteria:Test purpose: Ensure that the SUT, having sent the CON message, on receipt of the message



CON;REL; cause indicator: No. 16

Comments:

6.2.2.5 Receipt of the Suspend message (SUS) network initiated



criteria:Test purpose: Ensure that the SUT on receipt of the SUS message


values:SUS;

Comments:

6.2.2.6 Receipt of the Resume message (RES) network initiated



criteria:Test purpose: Ensure that the SUT on receipt of the RES message


values:SUS;RES;

Comments:

6.2.2.7 Release by the Exchange



criteria:Test purpose: Ensure that the SUT, having received a SUSPEND message containing the

suspend/resume indicator set to "network initiated", at expire of timer T6,sends a REL message with the cause parameter set to "recovery on timer expire

(102)"ISUP Parameter

values:SUS;RES;REL; cause parameter: recovery on timer expire (102)

Comments:

ETSI


6.2.3 Interworking from ISUP to DSS1

6.2.3.1 Sending of the SETUP message



TSS reference: ISUP-DSS1/Basic call/Sending of the SETUP messageISDN selection


criteria:Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing the complete

called party number and the sending complete indication,sends the SETUP message.


SETUP;


IAM; Called party number: complete numbersending complete

Comments: ISUP IAM -> SUT -> SETUP ISDN




criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]


Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing in the calledparty number with some digits, followed by SAM messages including the rest of the digitsand the last SAM providing in addition the sending complete indication,

sends the SETUP message after having received the last SAM message.ISDN Parameter

values:SETUP;


IAM; Called party number : digitsSAM1; subsequent number: additional digitsSAM2; subsequent number digits: last digits and sending complete address signal





criteria:called party addressing information split across, and sent in, SETUP and INFORMATIONmessages [A.62/MCn2.2]


Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing in the calledparty number with some digits, followed by SAM messages including the rest of the digitsand the last SAM providing in addition the sending complete indication,

sends the SETUP message.ISDN Parameter

values:SETUP;


IAM; Called party number : digitsSAM1; subsequent number: additional digitsSAM2; subsequent number digits: last digits and sending complete address signal


ETSI




ETS 300 356-1 [5], clauses 2.1.1, 2.1.8TSS reference: ISUP-DSS1/Basic call/Sending of the SETUP messageISDN selection


criteria:Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message with the nature of

connection indicator set to "continuity check required on this circuit (01)",does not send the SETUP message before it has received the COT message with the

continuity indicator set to "continuity check successful (1)".ISDN Parameter

values:SETUP;


IAM; nature of connection indicator: continuity check required on this circuit (01)COT; continuity indicator set to "continuity check successful (1)




ETS 300 356-1 [5], clauses 2.1.1, 2.1.8TSS reference: ISUP-DSS1/Basic call/Sending of the SETUP messageISDN selection


criteria:Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message with the nature of

connection indicator set to "continuity check required on a previous circuit (10)",does not send the SETUP message before it has received the COT message with the

continuity indicator set to "continuity check successful (1)".ISDN Parameter

values:SETUP;


IAM; nature of connection indicator: continuity check required on a previous circuit (01)COT; continuity indicator set to "continuity check successful (1)




ETS 300 356-1 [5], clause 2.1.1TSS reference: ISUP-DSS1/Basic call/Sending of the SETUP messageISDN selection

criteria:3,1 kHz audio [A.111/ISn1.2.4]


3,1 kHz audio [a.2/2]

Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing aTransmission Medium Requirement (TMR) set to "3,1 kHz audio" and without User ServiceInformation (USI),

sends the SETUP message with the Bearer Capability (BC) encoded as followed: theCoding standard set to " ITU-T standardized coding", the Information transfer capabilityset to "3,1 kHz audio" , the transfer mode set to "circuit mode" and the information transferrate set to "64 kbits/s".


SETUP; BC Coding standard: ITU-T standardized codingInformation transfer capability: 3,1 kHz audiotransfer mode: circuit modeinformation transfer rate: 64 kbits/s


IAM; TMR: 3,1 kHz audiono USI


ETSI





criteria:unrestricted digital information [A.111/ISn1.2.2] AND 64 kbits/s [A.111/ISn1.4.1]


64 kbit/s unrestricted [A.2/3]

Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing a TMR set to"64 kbit/s unrestricted" and without User Service Information (USI),

sends the SETUP message with the Bearer Capability (BC) encoded as followed: theCoding standard set to "ITU-T standardized coding", the Information transfer capability setto "unrestricted digital information" , the transfer mode set to "circuit mode" and theinformation transfer rate set to "64 kbits/s".


SETUP; BC Coding standard: ITU-T standardized codingInformation transfer capability: unrestricted digital informationtransfer mode: circuit modeinformation transfer rate: 64 kbits/s


IAM; TMR: 64 kbit/s unrestrictedno USI






criteria:Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message User Service

Information (USI) set to USI_VALUE,sends the SETUP message with the Bearer Capability (BC) set to USI_VALUE.


SETUP; BC: USI_VALUE (PIXIT)


IAM; USI: USI_VALUE (PIXIT)





criteria:speech [A.111/ISn1.2.1] AND unrestricted digital information with tones and announcements[A.111/ISn1.2.5]


speech [A.2/1] AND support signalling procedures for connection type allowing fallback([A.13/10])

Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message USI set to "speech" andthe USI Prime set to "unrestricted digital information with tones and announcements",

sends the SETUP message with the first Bearer Capability set to "speech" (the USIvalue) and the second BC set to "unrestricted digital information with tones andannouncements" (the USI prime value).


SETUP; first BC: speechsecond BC: unrestricted digital information with tones and announcements


IAM; USI: speechUSI Prime: unrestricted digital information with tones and announcement


ETSI






criteria:Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing the ISUP

indicator set to "ISUP not used all the way",sends the SETUP message with the progress indicator set to "call is not end-to-end

ISDN: further call progress information may be available in-band (#1)".ISDN Parameter

values:SETUP; progress indicator: call is not end-to-end ISDN: further call progress information maybe available in-band (#1)


IAM; ISUP indicator: ISUP not used all the way







indicator set to "ISUP used all the way" and the ISDN access indicator set to "originatingaccess non-ISDN",

sends the SETUP message with the progress indicator se tot "Originating access id nonISDN (#3)".


SETUP; progress indicator: Originating access id non ISDN (#3)


IAM; ISUP indicator: ISUP used all the wayISDN access indicator: originating access non-ISDN







indicator set to "ISUP used all the way" and the ISDN access indicator set to "originatingaccess ISDN" and an Access Transport Parameter (ATP) containing a progress indicator setto PI_VALUE,

sends the SETUP message with the progress indicator set to PI_VALUE.ISDN Parameter

values:SETUP; progress indicator: PI_VALUE (PIXIT)


IAM; ISUP indicator: ISUP used all the wayISDN access indicator: originating access ISDNATP progress indicator: PI_VALUE (PIXIT)


ETSI






criteria:Test purpose: Ensure that the SUT in Idle state, on receipt of an IAM message containing the Access

Transport Parameter (ATP) containing the Low Layer Compatibility (LLC) set to LLC_VALUE,sends the SETUP message with the LLC set to LLC_VALUE.


SETUP; LLC: LLC_VALUE (PIXIT)


IAM; ATP LLC: LLC_VALUE (PIXIT)







Transport Parameter (ATP) containing the High Layer Compatibility (HLC) set toHLC_VALUE,

sends the SETUP message with the HLC set to HLC_VALUE.ISDN Parameter

values:SETUP; HLC: HLC_VALUE (PIXIT)


IAM; ATP HLC: HLC_VALUE (PIXIT)







Transport Parameter (ATP) containing two High Layer Compatibility (HLC) set to respectivelyHLC_VALUE1 and HLC_VALUE2,

sends the SETUP message with two HLC in the same order HLC_VALUE1 andHLC_VALUE2.


SETUP; first HLC: HLC_VALUE1 (PIXIT)second HLC: HLC_VALUE2 (PIXIT)


IAM; ATP first HLC: HLC_VALUE1 (PIXIT)ATP second HLC: HLC_VALUE2 (PIXIT)


ETSI


6.2.3.2 Receipt of the SAM message



TSS reference: ISUP-DSS1/Basic call/receipt of the Subsequent Address Message (SAM)/ISDN selection

criteria:called party addressing information split across, and sent in, SETUP and INFORMATIONmessages [A.62/MCn2.2]


use the overlap operation in the forward address signalling (receiving) [A3/8]

Test purpose: Ensure that the SUT in call state N25 on receipt of a SAM message, containingadditional digits without sending complete indication,

sends the INFORMATION message providing additional digits.ISDN Parameter

values:INFORMATION messages; additional digits (PIXIT)


SAM; subsequent number (PIXIT)

Comments: ISUP SAM -> SUT -> INFORMATION ISDN

6.2.3.3 Sending of the ACM message

If tones/announcement are applied, the awaiting answer indication (e.g. ring tone) is sent to the calling party uponreceipt of the first ALERTING message. In this case the ACM message shall contain the OBCI with "in -bandinformation" set to: yes.



TSS reference: ISUP-DSS1/Basic call/Sending of the Address Complete Message (ACM)/ISDN selection

criteria:called party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]


Test purpose: Ensure that the SUT in call state N25, on receipt the ALERTING messagesends the ACM message with the Called Party's Status (CPS) indicator set to "

subscriber free (01)", the Called party's category indicator set to "no indication(00)" or"ordinary subscriber (01)" or "payphone (10)", the interworking indicator set to "nointerworking encountered (0)", the ISUP indicator set to "ISUP used all the way" and theISDN access indicator set to "ISDN" and if included the access delivery information isset to "Set-up message generated".


ALERTING;


ACM, CPS indicator: subscriber free (01)Called party's category indicator: no indication(00) or ordinary subscriber (01) orpayphone (10)interworking indicator: no interworking encountered (0)ISUP indicator: ISUP used all the wayISDN access indicator: ISDNaccess delivery information: Set-up message generated (IF PRESENT)

Comments: ISDN ALERTING -> SUT -> ACM ISUP

ETSI






criteria:Test purpose: Ensure that the SUT in call state N6, on receipt the ALERTING message

sends the ACM message with the CPS indicator set to " subscriber free (01)", theCalled party's category indicator set to "no indication(00)" or "ordinary subscriber (01)" or"payphone (10)", the interworking indicator set to "no interworking encountered (0)", theISUP indicator set to "ISUP used all the way" and the ISDN access indicator set to "ISDN"and if included the access delivery information is set to "Set-up message generated".


ALERTING;









Test purpose: Ensure that the SUT in call state N9, on receipt the ALERTING messagesends the ACM message with the CPS indicator set to " subscriber free (01)", the

Called party's category indicator set to "no indication(00)" or "ordinary subscriber (01)" or"payphone (10)", the interworking indicator set to "no interworking encountered (0)", theISUP indicator set to "ISUP used all the way" and the ISDN access indicator set to "ISDN"and if included the access delivery information is set to "Set-up message generated".


ALERTING;




ETSI







Test purpose: Ensure that the SUT in call state N25, on receipt of the CALL PROCEEDING messagesends the ACM message with the CPS indicator set to " no indication (00)", the Called

party's category indicator set to "no indication(00)" or "ordinary subscriber (01)" or"payphone (10)", the interworking indicator set to "no interworking encountered (0)", theISUP indicator set to "ISUP used all the way" and the ISDN access indicator set to "ISDN"and if included the access delivery information is set to "Set-up message generated".


CALL PROCEEDING;


ACM, CPS indicator: no indication (00)Called party's category indicator: no indication(00) or ordinary subscriber (01) orpayphone (10)interworking indicator: no interworking encountered (0)ISUP indicator: ISUP used all the wayISDN access indicator: ISDNaccess delivery information: Set-up message generated (IF PRESENT)

Comments: ISDN CALL PROCEEDING -> SUT -> ACM ISUP






Test purpose: Ensure that the SUT in call state N6, on receipt of the CALL PROCEEDING messagecontaining a progress indicator set to PI_VALUE,

sends the ACM message with the CPS indicator set to " no indication (00)", the Calledparty's category indicator set to "no indication(00)" or "ordinary subscriber (01)" or"payphone (10)", the interworking indicator set to "no interworking encountered (0)", theISUP indicator set to "ISUP used all the way", the ISDN access indicator set to "ISDN",the Access Transport Parameter (ATP) containing the progress indicator set toPI_VALUE and if included the access delivery information is set to "Set-up messagegenerated".


CALL PROCEEDING; progress indicator: PI_VALUE




ETSI







Test purpose: Ensure that the SUT in call state N9, on receipt of a PROGRESS message containingthe progress indicator set to PI_VALUE,

sends the ACM message with the CPS indicator set to " no indication (00)", the Calledparty's category indicator set to "no indication(00)" or "ordinary subscriber (01)" or"payphone (10)", the interworking indicator set to "no interworking encountered (0)", theISUP indicator set to "ISUP used all the way", the ISDN access indicator set to "ISDN",the Access Transport Parameter (ATP) containing the progress indicator set toPI_VALUE and if included the access delivery information is set to "Set-up messagegenerated".


PROGRESS; progress indicator: PI_VALUE



Comments: ISDN PROGRESS -> SUT -> ACM ISUP

Values for test purposes TP303005 and TP303006VA_01 PI_VALUE: Call is not end-to-end ISDN: further call progress information may be available

in-band (#1)VA_02 PI_VALUE: Destination address is non-ISDN (#2)






Test purpose: Ensure that the SUT in call state N6, on receipt of the CALL PROCEEDING messagecontaining a progress indicator set to PI_VALUE,

does not send the ACM message.ISDN Parameter

values:CALL PROCEEDING; progress indicator: PI_VALUE


Comments: ISDN CALL PROCEEDING -> SUT ->

ETSI







Test purpose: Ensure that the SUT in call state N9, on receipt of a PROGRESS message containingthe progress indicator set to PI_VALUE,


values:PROGRESS; progress indicator: PI_VALUE


Comments: ISDN PROGRESS -> SUT ->

Values for test purposes TP303007 and TP303008VA_01 PI_VALUE: originating address is non-ISDN (#3)VA_02 PI_VALUE: Call has returned to ISDN (#4)






Test purpose: Ensure that the SUT in call state N25, on receipt the ALERTING message containing aprogress indicator set to PI_VALUE

sends the ACM message with the CPS indicator set to " subscriber free (01)" and theAccess Transport Parameter (ATP) containing the progress indicator PI_VALUE.


ALERTING; progress indicator: PI_VALUE (PIXIT)


ACM, CPS indicator: subscriber free (01)ATP progress indicator: PI_VALUE (PIXIT)






criteria:Test purpose: Ensure that the SUT in call state N6, on receipt the ALERTING message containing a

progress indicator set to PI_VALUEsends the ACM message with the CPS indicator set to " subscriber free (01)" and the

ATP containing the progress indicator PI_VALUE.ISDN Parameter

values:ALERTING; progress indicator: PI_VALUE (PIXIT)




ETSI







Test purpose: Ensure that the SUT in call state N9, on receipt the ALERTING message containing aprogress indicator set to PI_VALUE

sends the ACM message with the CPS indicator set to " subscriber free (01)" and theATP containing the progress indicator PI_VALUE.


ALERTING; progress indicator: PI_VALUE (PIXIT)









Test purpose: Ensure that the SUT in call state N25, on receipt of the CALL PROCEEDING messagecontaining a progress indicator set to PI_VALUE

sends the ACM message with the CPS indicator set to " no indication (00)" and theATP containing the progress indicator PI_VALUE.


CALL PROCEEDING; progress indicator: PI_VALUE (PIXIT)


ACM, CPS indicator: no indication (00)ATP progress indicator: PI_VALUE (PIXIT)


ETSI




ETS 300 356-1 [5], clause 2.1.4TSS reference: ISUP-DSS1/Basic call/Sending of the Address Complete Message (ACM)/ISDN selection

criteria:AND called party addressing information split across, and send in, SETUP andINFORMATION messages [A.62/MCn2.2]AND T reference point [A1/R.3.2]AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback ([A.13/10]) AND speech[a.2/1] AND 3,1 kHz audio

Test purpose: Ensure that the SUT in call state N25, on receipt the ALERTING message containing theBearer Capability (BC) set to BC_VALUE and the progress indicator set to "Interworkinghas occurred and has resulted in a telecommunication service change (#5)"

sends the ACM message with the CPS indicator set to " subscriber free (01)", the ATPcontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"" and theTransmission Medium Used (TMU) set to USI_VALUE.


ALERTING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)BC: BC_VALUE


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUEACM, CPS indicator: subscriber free (01)ATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE





criteria:T reference point [A1/R.3.2] AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio[A.111/ISn1.2.4]



Test purpose: Ensure that the SUT in call state N6, on receipt the ALERTING message containing theBC set to BC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)"

sends the ACM message with the CPS indicator set to " subscriber free (01)", the ATPcontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"" and the TMU set toUSI_VALUE.






ETSI





criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND T reference point [A1/R.3.2] AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio[A.111/ISn1.2.4]



Test purpose: Ensure that the SUT in call state N9, on receipt the ALERTING message containing theBC set to BC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)"

sends the ACM message with the CPS indicator set to " subscriber free (01)", the ATPcontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"" and the TMU set toUSI_VALUE.









criteria:called party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]AND T reference point [A1/R.3.2]AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]



Test purpose: Ensure that the SUT in call state N25, on receipt of the CALL PROCEEDING messagecontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"

sends the ACM message with the CPS indicator set to " no indication (00)", the ATPcontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"" and the TMU set toUSI_VALUE.


CALL PROCEEDING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)BC: BC_VALUE


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUEACM, CPS indicator: no indication (00)ATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE


ETSI





criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND T reference point [A1/R.3.2]AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]



Test purpose: Ensure that the SUT in call state N6, on receipt of the CALL PROCEEDING messagecontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"

sends the ACM message with the CPS indicator set to " no indication (00)", the ATPcontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"" and the TMU set toUSI_VALUE.


CALL PROCEEDING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)BC: BC_VALUE







criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND T reference point [A1/R.3.2] AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio[A.111/ISn1.2.4]



Test purpose: Ensure that the SUT in call state N9, on receipt of a PROGRESS message containingthe BC set to BC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)"

sends the ACM message with the CPS indicator set to " no indication (00)" )", the ATPcontaining the BC set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)" and the TMU set toUSI_VALUE.


PROGRESS; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)BC: BC_VALUE




ETSI


Values and additional selection criteria for test purposes TP303013 to TP303018VA_01 USI_VALUE: speech

ISUP_VALUE: UDI/TABC_VALUE: speech

VA_02 USI_VALUE: 3.1ISUP_VALUE: UDI/TA

BC_VALUE: 3.1




criteria:called party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]AND T reference point [A.1/R3.2.]


Support signalling procedures for connection type allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in call state N25, on receipt the ALERTING message with aprogress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)" and with a HLC set to HLC_VALUE

sends the ACM message with the CPS indicator set to "subscriber free (01)", the ATPincluding the HLC set to HLC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)".


ALERTING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)


IAM; ATP first HLC: HLC_VALUE1 (PIXIT)ATP second HLC: HLC_VALUE2 (PIXIT)ACM, CPS indicator: subscriber free (01)ATP HLC: HLC_VALUE2 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)





criteria:T reference point [A.1/R3.2.]


support signalling procedures for connection type allowing fallback [A.13/10]








ETSI





criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND T reference point [A.1/R3.2.]


support signalling procedures for connection type allowing fallback ([A.13/10])












AND T reference point [A.1/R3.2.]ISUP selection


Test purpose: Ensure that the SUT in call state N25, on receipt of the CALL PROCEEDING messagewith a progress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)" and with a HLC set to HLC_VALUE

sends the ACM message with the CPS indicator set to " no indication (00)", the ATPincluding the HLC set to HLC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)".


CALL PROCEEDING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)


IAM; ATP first HLC: HLC_VALUE1 (PIXIT)ATP second HLC: HLC_VALUE2 (PIXIT)ACM, CPS indicator: no indication (00)ATP HLC: HLC_VALUE2 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)


ETSI





criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1AND T reference point [A.1/R3.2.]



Test purpose: Ensure that the SUT in call state N6, on receipt of the CALL PROCEEDING messagewith a progress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)" and with a HLC set to HLC_VALUE



CALL PROCEEDING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)







criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND T reference point [A.1/R3.2.]



Test purpose: Ensure that the SUT in call state N9, on receipt of a PROGRESS message with aprogress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)" and with a HLC set to HLC_VALUE



PROGRESS; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE2 (PIXIT)




ETSI







Test purpose: Ensure that the SUT in call state N6, on receipt of the CALL PROCEEDING messagecontaining no progress indicator,


values:CALL PROCEEDING; no progress indicator:








Test purpose: Ensure that the SUT in call state N9, on receipt of a PROGRESS message containingno progress indicator


values:PROGRESS; no progress indicator








Test purpose: Ensure that the SUT in call state N25, on receipt of the PROGRESS messagecontaining a progress indicator set to PI_VALUE,


values:PROGRESS; progress indicator: PI_VALUE (PIXIT VALUE different from: In-band toneinformation or an appropriate pattern now available (#8))



ETSI



ISUP ref. to:EN 300 899-1 [1], clause 3.1.1.3;ETS 300 356-1 [5], clause 2.1.4



criteria:PIXIT Automatic ACM

Test purpose: Ensure that the SUT, having received enough information in the IAM message,sends the ACM message with the CPS indicator set to "no indication", the ISUP

indicator set to "ISUP used all the way" and the ISDN access indicator set to "ISDN" andsends a SETUP message.



ACM; CPS indicator : no indicationISUP indicator: ISUP used all the wayISDN access indicator: ISDN

Comments: ISDN -> SUT -> ISUP ACM






Test purpose: Ensure that the SUT in call state N6, having received enough information in the IAM andhaving send automatically the ACM, on receipt of the CALL PROCEEDING message

does not send any message.ISDN Parameter

values:CALL PROCEEDING



6.2.3.4 Sending of the CPG message

If tones/announcement are applied, the awaiting answer indication (e.g. ring tone) is sent to the calling party uponreceipt of the first ALERTING message. In this case the CPG message shall contain the OBCI with "in -bandinformation" set to: yes.



TSS reference: ISUP-DSS1/Basic call/Sending of the Call Progress Message (CPG)/ISDN selection


criteria:Test purpose: Ensure that the SUT in call state N7, having sent the ACM message, on receipt of a

PROGRESS message,sends the CPG message with the event indicator set to "progress".


PROGRESS;


CPG; event indicator: progress

Comments: ISDN PROGRESS -> SUT -> CPG ISUP

ETSI







PROGRESS message,sends the CPG message with the event indicator set to "progress".


PROGRESS;


CPG; event indicator: progress






criteria:Test purpose: Ensure that the SUT in call state N9, having sent the ACM message, on receipt of an

ALERTING message,sends the CPG message with the event indicator set to "Alerting".


ALERTING;


CPG; event indicator: Alerting

Comments: ISDN ALERTING -> SUT -> CPG ISUP






PROGRESS message followed by an ALERTING message,sends two CPG messages respectively with the event indicator set to "Progress" and

"Alerting".ISDN Parameter

values:PROGRESS;ALERTING;


CPG 1; event indicator: ProgressCPG 2; event indicator: Alerting


ETSI







PROGRESS message containing the progress indicator set to PI_VALUE,sends the CPG message with the event indicator set to "Progress" and the ATP

containing the progress indicator set to PI_VALUE.ISDN Parameter



CPG; event indicator: ProgressATP progress indicator: PI_VALUE







PROGRESS message containing the progress indicator set to PI_VALUE,sends the CPG message with the event indicator set to "Progress" and the ATP

containing the progress indicator set to PI_VALUE.ISDN Parameter





Values and additional selection criteria for test purposes TP304005 and TP304006VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)





criteria:Test purpose: Ensure that the SUT in call state N9, having sent the ACM message with the ATP

containing the progress indicator set to "Destination address is non-ISDN (#2)", on receiptof a PROGRESS message containing the progress indicator set to " Call has returned tothe ISDN(#4)",

sends the CPG message with the event indicator set to "Progress" and the ATPcontaining the progress indicator set to " Call has returned to the ISDN(#4)".


CALL PROCEEDING; progress indicator: Destination address is non-ISDN (#2)PROGRESS; progress indicator: Call has returned to the ISDN(#4)


ACM; progress indicator: Destination address is non-ISDN (#2)CPG; event indicator: ProgressATP progress indicator: Call has returned to the ISDN(#4)


ETSI






criteria:Test purpose: Ensure that the SUT in call state N7, having sent the ACM message with the ATP

containing the progress indicator set to "Destination address is non-ISDN (#2)", on receiptof a PROGRESS message containing the progress indicator set to " Call has returned tothe ISDN(#4)",

sends the CPG message with the event indicator set to "Progress" and the ATPcontaining the progress indicator set to " Call has returned to the ISDN(#4)".


ALERTING; progress indicator: Destination address is non-ISDN (#2)PROGRESS; progress indicator: Call has returned to the ISDN(#4)


ACM; progress indicator: Destination address is non-ISDN (#2)CPG; event indicator: ProgressATP progress indicator: Call has returned to the ISDN(#4)



ISUP reference:EN 300 899-1 [1], clause 3.1.1.4.a;

ETS 300 356-1 [5], clause 2.1.5TSS reference: ISUP-DSS1/Basic call/Sending of the Call Progress Message (CPG)/ISDN selection



ALERTING message containing the progress indicator set to "Call is not end-to-end ISDN(#1)",

sends a CPG message with the event indicator set to "Alerting" and the ATP includingthe progress indicator set to "Call is not end-to-end ISDN (#1)".


ALERTING; progress indicator: Call is not end-to-end ISDN (#1)


CPG; Event indicator: AlertingATP progress indicator: Call is not end-to-end ISDN (#1)







ALERTING message containing the progress indicator set to "Destination address is non-ISDN (#2)",

sends a CPG message with the event indicator set to "Alerting" and the ATP includingthe progress indicator set to "Destination address is non ISDN (#2)".


ALERTING; progress indicator: Destination address is non-ISDN (#2)


CPG; Event indicator: AlertingATP progress indicator: Destination address is non-ISDN (#2)


ETSI







PROGRESS message containing the progress indicator set to "Call is not end-to-endISDN (#1)" followed by an ALERTING message,

sends a first CPG message with the Event indicator set to "Progress", the ATPincluding a progress indicator set to "Call is not end-to-end ISDN (#1)" and a second CPGmessage with the Event indicator set to " Alerting".


PROGRESS; progress indicator: Call is not end-to-end ISDN (#1)ALERTING


CPG1 ; Event indicator: ProgressATP progress indicator: Call is not end-to-end ISDN (#1)CPG2; Event indicator: Alerting







PROGRESS message containing the progress indicator set to "Destination address isnon-ISDN (#2)" followed by an ALERTING message,

sends a first CPG message with the Event indicator set to "Progress", the ATPprogress indicator set to "to "Destination address is non-ISDN (#2)" and a second CPGmessage with the Event indicator set to " Alerting".


PROGRESS; progress indicator: Destination address is non-ISDN (#2)ALERTING


CPG1 ; Event indicator: ProgressATP progress indicator: Destination address is non-ISDN (#2)CPG2; Event indicator: Alerting


ETSI





criteria:T reference point [A.1/R.3.2]AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISN1.2.4]


speech [A.2/1] AND 3,1 kHz audio [A.2/2] AND support signalling procedures for connectiontype allowing fallback ([A.13/10])

Test purpose: Ensure that the SUT in call state N9 having sent the ACM message, on receipt of aPROGRESS message containing the BC SET to BC_VALUE and the progress indicatorset to "Interworking has occurred and has resulted in a telecommunication service change(#5)"

sends the CPG message with the event indicator set to "Progress", the ATP containingthe BC set to BC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)" and the TMU set to USI_VALUE.




IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECPG, event indicator: ProgressATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE








Test purpose: Ensure that the SUT in call state N7 having sent the ACM message, on receipt of aPROGRESS message containing the BC set to BC_VALUE and the progress indicator setto "Interworking has occurred and has resulted in a telecommunication service change (#5)"





IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECPG; event indicator: ProgressATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE


ETSI








Test purpose: Ensure that the SUT in call state N9 having sent the ACM message, on receipt of anALERTING message containing the BC SET to BC_VALUE and the progress indicator setto "Interworking has occurred and has resulted in a telecommunication service change (#5)"

sends the CPG message with the event indicator set to "Alerting", the ATP containingthe BC set to BC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)" and the TMU set to USI_VALUE.




IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECPG; event indicator: AlertingATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE








Test purpose: Ensure that the SUT in call state N7 having sent the ACM message, on receipt of aPROGRESS message containing the BC SET to BC_VALUE and the progress indicatorset to "Interworking has occurred and has resulted in a telecommunication service change(#5)" and "In-band information or appropriate pattern is now available (#8)",

sends the CPG message with the event indicator set to "In-band information orappropriate pattern is now available", the ATP containing the BC set to BC_VALUE and theprogress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)" and the TMU set to USI_VALUE.


PROGRESS; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)progress indicator: In-band information or appropriate pattern is now available (#8)BC: BC_VALUE


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECPG; event indicator: In-band information or appropriate pattern is now availableATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE





BC_VALUE: 3.1

ETSI





criteria:T reference point [A.1/R.3.2]



Test purpose: Ensure that the SUT in call state N9, having sent the ACM message, on receipt of aPROGRESS message with a progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)" and with a HLC set to HLC_VALUE

sends the CPG message with event indicator set to "Progress", the ATP including theHLC set to HLC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)".




CPG, Event indicator: ProgressATP HLC: HLC_VALUE2 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)








Test purpose: Ensure that the SUT in call state N7, having sent the ACM message, on receipt of aPROGRESS message with a progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)" and with a HLC set to HLC_VALUE





CPG, Event indicator: ProgressATP HLC: HLC_VALUE2 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)


ETSI








Test purpose: Ensure that the SUT in call state N9, having sent the ACM message, on receipt of anALERTING message with a progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)" and with a HLC set to HLC_VALUE

sends the CPG message with event indicator set to "Alert", the ATP including the HLCset to HLC_VALUE and the progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)".




CPG, Event indicator: AlertingATP HLC: HLC_VALUE2 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)







Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of an ALERTING message,

sends the CPG message with the event indicator set to "Alerting".ISDN Parameter

values:ALERTING;


CPG; event indicator: Alerting







Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of an ALERTING message followed by a PROGRESS message,

sends two CPG message respectively with the event indicator set to "Alerting" and"Progress".


ALERTING;PROGRESS;


CPG 1; event indicator: AlertingCPG 2; event indicator: Progress


ETSI



ISUP ref. to:EN 300 899-1 [1], clause 3.1.1.4.a;




Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of an ALERTING message containing the progress indicator set to PI_VALUE,

sends two CPG message with the event indicator set to "Alerting" and the ATPincluding the progress indicator set to PI_VALUE.


ALERTING; progress indicator: PI_VALUE


CPG; Event indicator: AlertingATP progress indicator: PI_VALUE


Values and additional selection criteria for test purposes TP304023 and TP304024VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)






Test purpose: Ensure that the SUT in call state N6, having received an IAM with the USI fieldindicating USI_VALUE and having sent automatically the ACM message, on receipt of anALERTING message,

sends a CPG message with the event indicator set to "Alerting" and OBCI in-bandinformation set to "yes".


ALERTING;


IAM: USI: USI_VALUE;CPG; Event indicator: AlertingOBCI in-band: yes


Values and additional selection criteria for test purposes TP304024VA_01 USI_VALUE = speechVA_02 USI_VALUE = 3,1 kHz

ETSI







Test purpose: Ensure that the SUT in call state N9, having sent automatically the ACM message, onreceipt of a PROGRESS message containing the progress indicator set PI_VALUEfollowed by an ALERTING message,

sends a first CPG message with the Event indicator set PI_VALUE and a second CPGmessage with the Event indicator set to " Alerting".


PROGRESS; progress indicator : PI_VALUE (PIXIT)ALERTING;


CPG1 ; Event indicator: PI_VALUE (PIXIT)CPG2; Event indicator: Alerting


Values and additional selection criteria for test purposes TP304025VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)


ISUP ref. to:EN 300 899-1 [1], clause 3.1.1.4 table 75;


criteria:S/T reference point [A.1/R.3.1]AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISN1.2.4]


speech [A.2/1] AND 3,1 kHz audio [A.2/2] AND support signalling procedures for connectiontype allowing fallback ([A.13/10]) AND PIXIT Automatic ACM

Test purpose: Ensure that the SUT in call state N9 having sent automatically the ACM message, onreceipt of a PROGRESS message containing the BC set to BC_VALUE and the progressindicator set to "Interworking has occurred and has resulted in a telecommunication servicechange (#5)"





IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECPG; event indicator: ProgressATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE


ETSI





criteria:S/T reference point [A.1/R.3.1]AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISN1.2.4]


speech [A.2/1] AND 3,1 kHz audio [A.2/2] AND support signalling procedures for connectiontype allowing fallback ([A.13/10]) AND PIXIT Automatic ACM

Test purpose: Ensure that the SUT in call state N6 having sent automatically the ACM message, onreceipt of an ALERTING message containing the BC SET to BC_VALUE and the progressindicator set to "Interworking has occurred and has resulted in a telecommunication servicechange (#5)"

sends the CPG message with the event indicator set to "Alerting", the ATP containingthe BC set to BC_VALUE and the progress indicator set to "Interworking has occurred andhas resulted in a telecommunication service change (#5)" and the TMU set to USI_VALUE.




IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECPG; event indicator: AlertingATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE





BC_VALUE: 3.1




criteria:S/T reference point [A.1/R.3.1] AND


support signalling procedures for connection type allowing fallback ([A.13/10]) AND PIXITAutomatic ACM

Test purpose: Ensure that the SUT in call state N9, having sent automatically the ACM message, onreceipt of a PROGRESS message with a progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)" and with a HLC setto HLC_VALUE



PROGRESS; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE (PIXIT)


CPG, Event indicator: ProgressATP HLC: HLC_VALUE (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)


ETSI





criteria:S/T reference point [A.1/R.3.1] AND



Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of an ALERTING message with a progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)" and with a HLC setto HLC_VALUE

sends the CPG message with event indicator set to "Alert", the ATP including the HLCset to HLC_VALUE and the progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)".


ALERTING; progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)HLC: HLC_VALUE (PIXIT)


CPG, Event indicator: AlertingATP HLC: HLC_VALUE (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)


6.2.3.5 Sending of the ANM message



TSS reference: ISUP-DSS1/Basic call/Sending of the Answer Message (ANM)/ISDN selection



CONNECT messagesends the ANM message.


CONNECT;


ANM;

Comments: ISDN CONNECT -> SUT -> ANM ISUP






CONNECT messagesends the ANM message.


CONNECT;


ANM;


ETSI




ETS 300 356-1 [5], clause 2.1.7TSS reference: ISUP-DSS1/Basic call/Sending of the Answer Message (ANM)/ISDN selection



CONNECT message containing the progress indicator set to PI_VALUEsends the ANM message with the ATP including the progress indicator set to

PI_VALUE.ISDN Parameter

values:CONNECT; progress indicator: PI_VALUE (PIXIT)









CONNECT message containing the progress indicator set to PI_VALUEsends the ANM message with the ATP including the progress indicator set to











CONNECT message containing the LLC set to LLC_VALUEsends the ANM message with the ATP including the LLC set to LLC_VALUE.




ANM; ATP LLC: PI_VALUE (PIXIT)


ETSI







CONNECT message containing the LLC set to LLC_VALUEsends the ANM message with the ATP including the LLC set to LLC_VALUE.







ISUP reference:EN 300 899-1 [1], clause 3.1.1.5 tables 79 & 81;




Test purpose: Ensure that the SUT in call state N7, having sent the ACM message, on receipt of aCONNECT message containing the HLC set to HLC_VALUE1

sends the ANM message with the ATP including the HLC set to HLC_VALUE1.ISDN Parameter

values:CONNECT; HLC: LLC_VALUE2 (PIXIT)


IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)ANM; ATP HLC: HLC_VALUE2 (PIXIT)







Test purpose: Ensure that the SUT in call state N9, having sent the ACM message, on receipt of aCONNECT message containing the HLC set to HLC_VALUE1






ETSI





criteria:coincidence S and T reference [A.1/R.3.1]



Test purpose: Ensure that the SUT in call state N9, having received the IAM message with 2 HLCinformation elements set to HLC_VALUE1 and HLC_VALUE2 and having sent the ACMmessage, on receipt of a CONNECT message without HLC information element,


values:CONNECT; no HLC



















criteria:speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback [A.13/10] AND speech[A.2/1] AND 3,1 kHz audio [A.2/2]

Test purpose: Ensure that the SUT in call state N7, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message with BCinformation element set to BC_VALUE,

sends the ANM message with the ATP including the BC set to BC_VALUE and the TMUset to USI_VALUE.


CONNECT; BC: BC_VALUE


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUEANM; ATP BC: BC_VALUETMU: USI_VALUE


ETSI





criteria:AND speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback [A.13/10] AND speech[A.2/1] AND 3,1 kHz audio [A.2/2]

Test purpose: Ensure that the SUT in call state N9, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message with BCinformation element set to BC_VALUE,







Values and additional selection criteria for test purposes TP305011 and TP305012VA_01 USI_VALUE: speech



BC_VALUE: 3.1






Test purpose: Ensure that the SUT in call state N9, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message with BCinformation element set to "unrestricted digital information with tones and announcements",

sends the ANM message with the ATP including the BC set to "unrestricted digitalinformation with tones and announcements", and without TMU.


CONNECT; BC: unrestricted digital information with tones and announcements


IAM; USI: USI_VALUE (PIXIT)USI prime: unrestricted digital information with tones and announcementsTMR: 64 kbit/s preferredTMR prime: USI_VALUE (PIXIT)ANM; ATP BC: unrestricted digital information with tones and announcements"


ETSI







Test purpose: Ensure that the SUT in call state N7, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message with BCinformation element set to "unrestricted digital information with tones and announcements",










criteria:Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback ([A.13/10]) AND speech[A.2/1] AND 3,1 kHz audio [A.2/2]

Test purpose: Ensure that the SUT in call state N9, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message withoutBC information element,

sends the ANM message with the ATP including the BC set to USI_VALUE and theTMU set to USI_VALUE.


CONNECT; no BC


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUEANM; ATP BC: USI_VALUETMU: USI_VALUE


ETSI







support signalling procedures for connection type allowing fallback ([A.13/10]) AND speech[A.2/1] AND 3,1 kHz audio [A.2/2]

Test purpose: Ensure that the SUT in call state N7, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message withoutBC information element,



CONNECT; no BC





ISUP_VALUE: UDI/TAVA_02 USI_VALUE: 3,1 kHz audio

ISUP_VALUE: UDI/TA







Test purpose: Ensure that the SUT in call state N7, having sent the ACM message, on receipt of aCONNECT message containing the HLC set to HLC_VALUE1 and the progress indicatorset to "Interworking has occurred and has resulted in a telecommunication service change(#5)"

sends the ANM message with the ATP including the HLC set to HLC_VALUE1 and theprogress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)".


CONNECT; HLC: HLC_VALUE1 (PIXIT)progress indicator: Interworking has occurred and has resulted in a telecommunicationservice change (#5)


IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)ANM; ATP HLC: HLC_VALUE1 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)


ETSI








Test purpose: Ensure that the SUT in call state N9, having sent the ACM message, on receipt of aCONNECT message containing the HLC set to HLC_VALUE1 and the progress indicatorset to "Interworking has occurred and has resulted in a telecommunication service change(#5)"














sends the ANM message without the ATP including the HLC.ISDN Parameter



IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)ANM; ATP no HLC












IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)ANM; no HLC


ETSI





criteria:T reference point [A.1/R.3.2] AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio[A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback ([A.13/10]) AND Speech[A.2/1] AND 3,1 kHz audio [A.2/2]

Test purpose: Ensure that the SUT in call state N9, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message with BCinformation element set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"

sends the ANM message with the ATP including the BC set to BC_VALUE and the TMUset to USI_VALUE and the progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)".


CONNECT; BC: BC_VALUEprogress indicator: Interworking has occurred and has resulted in a telecommunicationservice change (#5)


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUEANM; ATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE





criteria:T reference point [A.1/R.3.2] AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio[A.111/ISn1.2.4]



Test purpose: Ensure that the SUT in call state N7, having received the IAM message indicating BCfallback and having sent the ACM message, on receipt of a CONNECT message with BCinformation element set to BC_VALUE and the progress indicator set to "Interworking hasoccurred and has resulted in a telecommunication service change (#5)"










BC_VALUE: 3.1

ETSI







Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of a CONNECT message

sends the ANM message.ISDN Parameter

values:CONNECT;


ANM;







Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of a CONNECT message containing the progress indicator set to PI_VALUE

sends the ANM message with the ATP including the progress indicator set toPI_VALUE.











Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of a CONNECT message containing the LLC set to LLC_VALUE

sends the ANM message with the ATP including the LLC set to LLC_VALUE.ISDN Parameter

values:CONNECT; LLC: LLC_VALUE (PIXIT)




ETSI



ISUP ref. to:EN 300 899-1 [1], clause 3.1.1.5 tables 79 & 81;



criteria:support signalling procedures for connection type allowing fallback ([A.13/10]) AND PIXITAutomatic ACM

Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of a CONNECT message containing the HLC set to HLC_VALUE1












Test purpose: Ensure that the SUT in call state N6, having received the IAM message with 2 HLCinformation elements set to HLC_VALUE1 and HLC_VALUE2 and having sent automaticallythe ACM message, on receipt of a CONNECT message without HLC information element,









criteria:speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback [A.13/10] AND speech[A.2/1] AND 3,1 kHz audio [A.2/2] AND PIXIT Automatic ACM

Test purpose: Ensure that the SUT in call state N6, having received the IAM message indicating BCfallback allowed and having sent automatically the ACM message, on receipt of aCONNECT message with BC information element set to BC_VALUE,







ETSI


Values and additional selection criteria for test purposes TP305028VA_01 USI_VALUE: speech



BC_VALUE: 3.1





criteria:support signalling procedures for connection type allowing fallback ([A.13/10]) AND PIXITAutomatic ACM

Test purpose: Ensure that the SUT in call state N6, having received the IAM message indicating BCfallback allowed and having sent automatically the ACM message, on receipt of aCONNECT message with BC information element set to "unrestricted digital informationwith tones and announcements",












support signalling procedures for connection type allowing fallback ([A.13/10]) AND speech[A.2/1] AND 3,1 kHz audio [A.2/2] AND PIXIT Automatic ACM

Test purpose: Ensure that the SUT in call state N6, having received the IAM message indicating BCfallback allowed and having sent automatically the ACM message, on receipt of aCONNECT message without BC information element,



CONNECT; no BC






ISUP_VALUE: UDI/TA

ETSI





criteria:S/T reference point [A.1/R.3.1]



Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of a CONNECT message containing the HLC set to HLC_VALUE1 and theprogress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)"













Test purpose: Ensure that the SUT in call state N6, having received the IAM message with 2 HLCinformation elements set to HLC_VALUE1 and HLC_VALUE2 and having sent automaticallythe ACM message, on receipt of a CONNECT message without HLC information element,




IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)ANM; no HLC


ETSI





criteria:S/T reference point [A.1/R.3.1] AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio[A.111/ISn1.2.4]


support signalling procedures for connection type allowing fallback ([A.13/10]) AND Speech[A.2/1] AND 3,1 kHz audio [A.2/2] AND PIXIT Automatic ACM

Test purpose: Ensure that the SUT in call state N6, having received the IAM message indicating BCfallback allowed and having sent automatically the ACM message, on receipt of aCONNECT message with BC information element set to BC_VALUE and the progressindicator set to "Interworking has occurred and has resulted in a telecommunication servicechange (#5)"










BC_VALUE: 3.1

6.2.3.6 Sending of the CON message



TSS reference: ISUP-DSS1/Basic call/Sending of the Connect Message (CON)/ISDN selection



Test purpose: Ensure that the SUT in call state N25, having not sent the ACM message, on receipt of aCONNECT message

sends the CON message with the BCI encoded as followed:Interworking indicator: no interworking encounteredISUP indicator: ISUP used all the wayISDN access indicator: ISDNCPS indicator: subscriber free


CONNECT;


CON; BCI interworking indicator: no interworking encounteredISUP indicator: ISUP used all the wayISDN access indicator: ISDNCPS indicator: subscriber free

Comments: ISDN CONNECT -> SUT -> CON ISUP

ETSI










CONNECT;






TSS reference: ISUP-DSS1/Basic call/Sending of the Connect Message (CON)/En-bloc





CONNECT;









Test purpose: Ensure that the SUT in call state N25, having not sent the ACM message, on receipt of aCONNECT message including the progress indicator set to PI_VALUE.

sends the CON message with the ATP including the progress indicator set toPI_VALUE.




CON; ATP progress indicator: PI_VALUE (PIXIT)


ETSI







Test purpose: Ensure that the SUT in call state N9, having not sent the ACM message, on receipt of aCONNECT message including the progress indicator set to PI_VALUE.

sends the CON message with the ATP including the progress indicator set toPI_VALUE.










criteria:Test purpose: Ensure that the SUT in call state N6, having not sent the ACM message, on receipt of a

CONNECT message including the progress indicator set to PI_VALUE.sends the CON message with the ATP including the progress indicator set to











Test purpose: Ensure that the SUT in call state N25, having not sent the ACM message, on receipt of aCONNECT message including the LLC set to LLC_VALUE.

sends the CON message with the ATP including the LLC set to LLC_VALUE.ISDN Parameter



CON; ATP LLC: LLC_VALUE (PIXIT)


ETSI







Test purpose: Ensure that the SUT in call state N9, having not sent the ACM message, on receipt of aCONNECT message including the LLC set to LLC_VALUE.

sends the CON message with the ATP including the LLC set to LLC_VALUE.ISDN Parameter









criteria:Test purpose: Ensure that the SUT in call state N6, having not sent the ACM message, on receipt of a

CONNECT message including the LLC set to LLC_VALUE.sends the CON message with the ATP including the LLC set to LLC_VALUE.











Test purpose: Ensure that the SUT in call state N25, having not sent the ACM message, on receipt of aCONNECT message containing the HLC set to HLC_VALUE1

sends the CON message with the ATP including the HLC set to HLC_VALUE1.ISDN Parameter



IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)CON; ATP HLC: HLC_VALUE1 (PIXIT)


ETSI




























ETS 300 356-1 [5], clause 2.1.4TSS reference: ISUP-DSS1/Basic call/Sending of the Connect Message (CON)/ISDN selection

criteria:coincidence S T reference [A.1/R.3.1]AND called party addressing information split across, and send in, SETUP andINFORMATION messages [A.62/MCn2.2]



Test purpose: Ensure that the SUT in call state N25, having received the IAM message with 2 HLCinformation elements set to HLC_VALUE1 and HLC_VALUE2 and having not sent the ACMmessage, on receipt of a CONNECT message without HLC information element,






ETSI





criteria:coincidence S T reference [A.1/R.3.1] ANDCalled party addressing information send only in the SETUP message [A.62/MCn.2.1]












criteria:coincidence S T reference [A.1/R.3.1]












criteria:called party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]


support signalling procedures for connection type allowing fallback ([A.13/10]) AND Speech [A.2/1]AND 3,1 kHz audio [A.2/2]

Test purpose: Ensure that the SUT in call state N25, having received the IAM message indicating BC fallbackand having not sent the ACM message, on receipt of a CONNECT message with BC informationelement set to BC_VALUE,

sends the CON message with the ATP including the BC set to BC_VALUE and the TMU set toUSI_VALUE .




IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECON; ATP BC: BC_VALUETMU: USI_VALUE


ETSI





criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]




sends the CON message with the ATP including the BC set to BC_VALUE and the TMU set toUSI_VALUE.









criteria:Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]




sends the CON message with the ATP including the BC set to BC_VALUE and the TMU set toUSI_VALUE.









BC_VALUE: 3.1

ETSI








Test purpose: Ensure that the SUT in call state N25, having received the IAM message indicating BC fallbackand having not sent the ACM message, on receipt of a CONNECT message with BC informationelement set to "unrestricted digital information with tones and announcements",

sends the CON message with the ATP including the BC set to "unrestricted digital informationwith tones and announcements", and without TMU.




IAM; USI: USI_VALUE (PIXIT)USI prime: unrestricted digital information with tones and announcementsTMR: 64 kbit/s preferredTMR prime: USI_VALUE (PIXIT)CON; ATP BC: unrestricted digital information with tones and announcements"







Test purpose: Ensure that the SUT in call state N6, having received the IAM message indicating BCfallback and having not sent the ACM message, on receipt of a CONNECT message withBC information element set to "unrestricted digital information with tones andannouncements",

sends the CON message with the ATP including the BC set to "unrestricted digitalinformation with tones and announcements", and without TMU.






ETSI








Test purpose: Ensure that the SUT in call state N9, having received the IAM message indicating BC fallbackand having not sent the ACM message, on receipt of a CONNECT message with BC informationelement set to "unrestricted digital information with tones and announcements",

sends the CON message with the ATP including the BC set to "unrestricted digital informationwith tones and announcements", and without TMU.









criteria:called party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]



Test purpose: Ensure that the SUT in call state N25, having received the IAM message indicating BC fallbackand having not sent the ACM message, on receipt of a CONNECT message without BC informationelement,

sends the CON message with the ATP including the BC set to USI_VALUE and the TMU set toUSI_VALUE.


CONNECT; no BC


IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECON; ATP BC: USI_VALUETMU: USI_VALUE


ETSI





criteria:Called party addressing information send only in the SETUP message [A.62/MCn.2.1]AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]






CONNECT; no BC







criteria:Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]






CONNECT; no BC






ISUP_VALUE: UDI/TA

ETSI





criteria:T reference point [A.1/R.3.2] ANDcalled party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]



Test purpose: Ensure that the SUT in call state N25, having not sent the ACM message, on receipt of aCONNECT message containing the HLC set to HLC_VALUE1 and the progress indicatorset to "Interworking has occurred and has resulted in a telecommunication service change(#5)"

sends the CON message with the ATP including the HLC set to HLC_VALUE1 and theprogress indicator set to "Interworking has occurred and has resulted in atelecommunication service change (#5)".


CONNECT; HLC: LLC_VALUE1 (PIXIT)progress indicator: Interworking has occurred and has resulted in a telecommunicationservice change (#5)


IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)CON; ATP HLC: HLC_VALUE1 (PIXIT)ATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)





criteria:T reference point [A.1/R.3.2] ANDCalled party addressing information send only in the SETUP message [A.62/MCn.2.1]










ETSI


















criteria:T reference point [A.1/R.3.2] ANDcalled party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]



Test purpose: Ensure that the SUT in call state N25, having received the IAM message with 2 HLCinformation elements set to HLC_VALUE1 and HLC_VALUE2 and not having sent the ACMmessage, on receipt of a CONNECT message without HLC information element,

sends the CON message without the ATP including the HLC.ISDN Parameter



IAM; ATP HLC1: HLC_VALUE1 (PIXIT)ATP HLC2: HLC_VALUE2 (PIXIT)CON; ATP no HLC





criteria:T reference point [A.1/R.3.2] ANDCalled party addressing information send only in the SETUP message [A.62/MCn.2.1]









ETSI

















criteria:T reference [A.1/R.3.2] ANDcalled party addressing information split across, and send in, SETUP and INFORMATIONmessages [A.62/MCn2.2]AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]



Test purpose: Ensure that the SUT in call state N25, having received the IAM message indicating BCfallback and having not sent the ACM message, on receipt of a CONNECT message withBC information element set to BC_VALUE and the progress indicator set to "Interworkinghas occurred and has resulted in a telecommunication service change (#5)"

sends the CON message with the ATP including the BC set to BC_VALUE and the TMUset to USI_VALUE and the progress indicator set to "Interworking has occurred and hasresulted in a telecommunication service change (#5)".




IAM; USI: USI_VALUEUSI prime: ISUP_VALUETMR: 64 kbit/s preferredTMR prime: USI_VALUECON; ATP BC: BC_VALUEATP progress indicator: Interworking has occurred and has resulted in atelecommunication service change (#5)TMU: USI_VALUE


ETSI





criteria:T reference [A.1/R.3.2] ANDCalled party addressing information send only in the SETUP message [A.62/MCn.2.1] ANDSpeech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]













criteria:T reference [A.1/R.3.2] AND Speech [A.111/ISn1.2.1] AND 3,1 kHz audio [A.111/R.3.2]













BC_VALUE: 3.1

ETSI



If tones/announcement are applied, a DISCONNECT message which is sent in state 10 shall contain a progressindicator #8. As an alternative, a PROGRESS message may be sent containing progress indicator #8.

TP307101 ISDN reference:EN 300 403-1 [6], clause 5.2.5.3


ETS 300 356-1 [5], clause 2.2TSS reference: ISUP-DSS1/Basic call/Receipt of the Release message (REL)/ISDN selection



Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message and onreceipt REL message with the Cause value CV_ISUP, location LOC_ISUP

sends a DISCONNECT message with the Cause value CV_ISDN, location LOC_ISDN.ISDN Parameter

values:SETUPDISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)





criteria:T reference point [A.1/R.3.2]AND called party addressing information split across, and send in, SETUP andINFORMATION messages [A.62/MCn2.2]


Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message , and on receipt of a REL message with the Causevalue CV_ISUP, location LOC_ISUP


values:SETUPSETUP ACKNOWLEDGEDISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message, and on receipt of a SAM message followed by a RELmessage with the Cause value CV_ISUP, location LOC_ISUP

sends a INFORMATION message followed by a DISCONNECT message with theCause value CV_ISDN, location LOC_ISDN.


SETUP;SETUP ACKNOWLEDGE;INFORMATIONDISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a REL message with the Cause value CV_ISUP,location LOC_ISUP


values:SETUP;CALL PROCEEDING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message followed by a PROGRESS message with a progressindicator where the progress description value is set to PI_VALUE, sends out an ACMMessage where the CPS indicator is set to "no indication" followed by a CPG messagewhere the Event indicator is set to Progress and on receipt of a REL message with theCause value CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;PROGRESS; progress description: PI_VALUE (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: "no indication"CPG; Event indicator: ProgressREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING message, sends out an ACMMessage where the CPS indicator is set to "subscriber free" and on receipt of a RELmessage with the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;SETUP ACKNOWLEDGE;ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: subscriber freeREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting and on receipt of a REL message with the Causevalue CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indicationCPG; Event indicator: AlertingREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a ALERTING Message goes to state N7,sends out a CPG message where the Event indicator is set to Alerting and on receipt of aREL message with the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationCPG; Event indicator: ProgressCPG; Event indicator: AlertingREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a REL message with the Cause valueCV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS; progress indicator: PI_VALUE (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationCPG; Event indicator: AlertingCPG; Event indicator: ProgressREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)





criteria:T reference point [A.1/R.3.2] OR Coincident S and T reference point [A.1/R.3.1]


Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator isset to "no indication" receives a CONNECT message, sends out an ANM message and onreceipt of a REL message with the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationANM;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI





criteria:T reference point [A.1/R.3.2] OR Coincident S and T reference point [A.1/R.3.1]


Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCONNECT message, sends out an CON message and on receipt of a REL message withthe Cause value CV_ISUP, location LOC_ISUP

sends a DISCONNECT message with the Cause value CV_ISDN, location LOC_ISDNISDN Parameter

values:SETUP;CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;CONNECT;REL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)





criteria:Coincident S and T reference point [A.1/R.3.1]AND called party addressing information split across, and send in, SETUP andINFORMATION messages [A.62/MCn2.2]


Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message, and on receipt of a REL message with the Causevalue CV_ISUP, location LOC_ISUP

sends a RELEASE message with the Cause value CV_ISDN, location LOC_ISDN.ISDN Parameter

values:SETUPSETUP ACKNOWLEDGERELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)



Comments: ISUP REL -> SUT -> RELEASE ISDN

ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message and on receipt of a SAM message followed by a RELmessage with the Cause value CV_ISUP, location LOC_ISUP

sends a INFORMATION message followed by a RELEASE message with the Causevalue CV_ISDN, location LOC_ISDN.


SETUP;SETUP ACKNOWLEDGE;INFORMATIONRELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)







criteria:Coincident S and T reference point [A.1/R.3.1]


Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a REL message with the Cause value CV_ISUP,location LOC_ISUP


values:SETUP;CALL PROCEEDING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message followed by a PROGRESS message with a progressindicator where the progress description value is set to PI_VALUE, sends out an ACMMessage where the CPS indicator is set to "no indication" followed by a CPG messagewhere the Event indicator is set to Progress and on receipt of a REL message with theCause value CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: "no indication"CPG; Event indicator: ProgressREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING message, sends out an ACMMessage where the CPS indicator is set to "subscriber free" and on receipt of a RELmessage with the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;SETUP ACKNOWLEDGE;ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: subscriber freeREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting and on receipt of a REL message with the Causevalue CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: no indicationCPG; Event indicator: AlertingREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a ALERTING Message, sends out a CPGmessage where the Event indicator is set to Alerting and on receipt of a REL messagewith the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationCPG; Event indicator: ProgressCPG; Event indicator: AlertingREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a REL message with the Cause valueCV_ISUP, location LOC_ISUP


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS; progress indicator : PI_VALUE (PIXIT)RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationCPG; Event indicator: AlertingCPG; Event indicator: ProgressREL: cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


TP307301 ISDN ref. to:EN 300 403-1 [6], clause 5.2.5.3

ISUP ref. to:EN 300 899-1 [1], clause 3.1.1.7;




PIXIT Automatic ACM

Test purpose: Ensure that the SUT in state N9, having sent automatically the ACM message, onreceipt of a REL message with the Cause value CV_ISUP, location LOC_ISUP






ETSI


6.2.3.8 Sending of a REL message (REL)



ETS 300 356-1 [5], clause 2.2TSS reference: ISUP-DSS1/Basic call/Sending of the Release message (REL)/ISDN selection


criteria:Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message and on

receipt RELEASE COMPLETE message with the Cause value CV_ISDN, locationLOC_ISDN

sends a REL message with the Cause value CV_ISUP, location LOC_ISUP.ISDN Parameter

values:SETUPRELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







receipt RELEASE message with the Cause value CV_ISDN, location LOC_ISDNsends a REL message with the Cause value CV_ISUP, location LOC_ISUP.


SETUPRELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









receipt DISCONNECT message with the Cause value CV_ISDN, location LOC_ISDNsends a REL message with the Cause value CV_ISUP, location LOC_ISUP.


SETUPDISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message , and on receipt of a RELEASE COMPLETE messagewith the Cause value CV_ISDN, location LOC_ISDN


values:SETUPSETUP ACKNOWLEDGERELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message and on receipt of a RELEASE message with the Causevalue CV_ISDN, location LOC_ISDN


values:SETUPSETUP ACKNOWLEDGERELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message and on receipt of a DISCONNECT message with theCause value CV_ISDN, location LOC_ISDN


values:SETUPSETUP ACKNOWLEDGEDISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message, on receipt of a SAM message sends a INFORMATIONmessage and on receipt of a REL EASE COMPLETE message with the Cause valueCV_ISDN, location LOC_ISDN


values:SETUPSETUP ACKNOWLEDGEINFORMATIONREL EASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;SAM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message, on receipt of a SAM message sends a INFORMATIONmessage and on receipt of a REL EASE message with the Cause value CV_ISDN,location LOC_ISDN


values:SETUPSETUP ACKNOWLEDGEINFORMATIONREL EASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message, on receipt of a SAM message sends a INFORMATIONmessage and on receipt of a DISCONNECT message with the Cause value CV_ISDN,location LOC_ISDN


values:SETUP;SETUP ACKNOWLEDGE;INFORMATION;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)








criteria:Test purpose: Ensure that the SUT after receiving the IAM sends a SETUP message, and receives a

CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a RELEASE COMPLETE message with the Causevalue CV_ISDN, location LOC_ISDN


values:SETUP; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDN,CALL PROCEEDING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI






criteria:Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives a

CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a RELEASE message with the Cause value CV_ISDN,location LOC_ISDN


values:SETUP;CALL PROCEEDING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)








criteria:Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives a

CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a DISCONNECT message with the Cause valueCV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI






criteria:Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives a

CALL PROCEEDING message followed by a PROGRESS message with a progressindicator PI_VALUE, sends out an ACM Message where the CPS indicator is set to "noindication" followed by a CPG message where the Event indicator is set to Progress andon receipt of a RELEASE COMPLETE message with the Cause value CV_ISDN, locationLOC_ISDN


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: "no indication"CPG; Event indicator: Progress, progress indicator No.1REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







CALL PROCEEDING message followed by a PROGRESS message with a progressindicator PI_VALUE, sends out an ACM Message where the CPS indicator is set to "noindication" followed by a CPG message where the Event indicator is set to Progress andon receipt of a RELEASE message with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: "no indication"CPG; Event indicator: Progress; progress indicator No.1REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







CALL PROCEEDING message followed by a PROGRESS message with a progressindicator PI_VALUE, sends out an ACM Message where the CPS indicator is set to "noindication" followed by a CPG message where the Event indicator is set to Progress andon receipt of a DISCONNECT message with the Cause value CV_ISDN, locationLOC_ISDN


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


ACM; CPS indicator: "no indication"CPG; Event indicator: Progress; progress indicator No.1REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING message, sends out an ACMMessage where the CPS indicator is set to "subscriber free" and on receipt of a RELEASECOMPLETE message with the Cause value CV_ISDN, location LOC_ISDN

sends a REL message with the Cause value CV_ISUP, location LOC_ISUPISDN Parameter

values:SETUP;SETUP ACKNOWLEDGE;ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM;CPS indicator: subscriber freeREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING message, sends out an ACMMessage where the CPS indicator is set to "subscriber free" and on receipt of a RELEASEmessage with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;SETUP ACKNOWLEDGE;ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAMACM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING, sends out an ACM Messagewhere the CPS indicator is set to "subscriber free" and on receipt of a DISCONNECTmessage with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;SETUP ACKNOWLEDGE;ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAMACM;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI






criteria:Test purpose: Ensure that the SUT after receiving the IAM, sends out a SETUP message, receives a

CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting and on receipt of a RELEASE COMPLETE messagewith the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM;CPG;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting and on receipt of a RELEASE message with theCause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting and on receipt of a DISCONNECT message with theCause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a ALERTING Message, sends out a CPGmessage where the Event indicator is set to Alerting and on receipt of a RELEASECOMPLETE message with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;CPG;CPG;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a ALERTING Message, sends out a CPGmessage where the Event indicator is set to Alerting and on receipt of a RELEASEmessage with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a ALERTING Message, sends out a CPGmessage where the Event indicator is set to Alerting and on receipt of a DISCONNECTmessage with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a RELEASE COMPLETE message with theCause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS; progress indicator: PI_VALUE (PIXIT)RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM;CPG;CPG;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a RELEASE message with the Cause valueCV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to Alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to Progress, and on receipt of a DISCONNECT message with the Causevalue CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS; progress indicator: PI_VALUE (PIXIT)DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









CALL PROCEEDING message, sends out an ACM message where the CPS indicator isset to "no indication" receives a CONNECT message, sends out an ANM message and onreceipt of a RELEASE COMPLETE message with the Cause value CV_ISDN, locationLOC_ISDN


values:SETUP;CALL PROCEEDING;CONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;ACM; CPS indicator: no indicationREL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)


ETSI







CALL PROCEEDING message, sends out an ACM message where the CPS indicator isset to "no indication" receives a CONNECT message, sends out an ANM message and onreceipt of a RELEASE message with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;CONNECT;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









CALL PROCEEDING message, sends out an ACM message where the CPS indicator isset to "no indication" receives a CONNECT message, sends out an ANM message and onreceipt of a DISCONNECT message with the Cause value CV_ISDN, location LOC_ISDN


values:SETUP;CALL PROCEEDING;CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CONNECT message, sends out a CON message and on receipt of a RELEASECOMPLETE message with the Cause value CV_ISUP, location LOC_ISUP

sends a REL message with the Cause value CV_ISDN, location LOC_ISDNISDN Parameter

values:SETUP;CONNECT;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)


IAM;CONNECT;REL; cause value: CV_ISUP (PIXIT)location: LOC_ISUP (PIXIT)







CONNECT message sends out a CON message and on receipt of a RELEASE messagewith the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;CONNECT;RELEASE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)




ETSI







CONNECT message, sends out a CON message and on receipt of a DISCONNECTmessage with the Cause value CV_ISUP, location LOC_ISUP


values:SETUP;CONNECT;DISCONNECT; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)





ISUP reference:EN 300 899-1 [1], clause A.2.2.3;


criteria:multipoint configuration[A.1/R7.2]


Test purpose: Ensure that the SUT after receiving the IAM, sends out a SETUP message via abroadcast data link, receives a RELEASE COMPLETE message with the Cause valueCV_ISUP, location LOC_ISUP

sends a REL message after time-out of T303 with the Cause value CV_ISDN, locationLOC_ISDN


SETUP;RELEASE COMPLETE; cause value: CV_ISDN (PIXIT)location: LOC_ISDN (PIXIT)









Test purpose: Ensure that the SUT in state N6, having sent automatically the ACM message, onreceipt RELEASE COMPLETE message with the Cause value CV_ISDN, locationLOC_ISDN






ETSI







Test purpose: Ensure that the SUT in state N6, having sent automatically the ACM message, onreceipt RELEASE message with the Cause value CV_ISDN, location LOC_ISDN











Test purpose: Ensure that the SUT in state N6, having sent automatically the ACM message, onreceipt DISCONNECT message with the Cause value CV_ISDN, location LOC_ISDN






6.2.3.9 Receipt of Reset circuit message (RSC), Circuit group reset message (GRS)or Circuit group blocking message (CGB) with the indication hardware failureoriented

6.2.3.9.1 Receipt of Reset Circuit message (RSC)



TSS reference: ISUP-DSS1/Basic call/Receipt of Reset circuit message (RSC), Circuit group reset message(GRS) or Circuit group blocking message (CGB) with the indication hardware failure oriented



Test purpose: Ensure that the SUT in state N9, having sent the ACM message, on receipt of a RSCmessage,




RSC


ETSI







Test purpose: Ensure that the SUT in state N7, having sent the ACM message, on receipt of a RSCmessage,




RSC







Test purpose: Ensure that the SUT in state N10, on receipt of a RSC message,sends the DISCONNECT message with the cause value set to "normal, unspecified (31)"




RSC







Test purpose: Ensure that the SUT in state N25, on receipt of a RSC message,sends the DISCONNECT message


no DISCONNECT


RSC


ETSI







Test purpose: Ensure that the SUT in Idle state, on receipt of a RSC message,does not send the DISCONNECT message


no DISCONNECT


RSC


6.2.3.9.2 Receipt of Circuit Group Reset message (GRS)






Test purpose: Ensure that the SUT in state N9, having sent the ACM message, on receipt of a GRSmessage ,




GRS;







Test purpose: Ensure that the SUT in state N7, having sent the ACM message, on receipt of a GRSmessage,




GRS;


ETSI







Test purpose: Ensure that the SUT in state N10, on receipt of a GRS message,sends the DISCONNECT message with the cause value set to "normal, unspecified (31)"




GRS;







Test purpose: Ensure that the SUT in state N25, on receipt of a GRS message,sends the DISCONNECT message


no DISCONNECT


GRS;







Test purpose: Ensure that the SUT in Idle state, on receipt of a GRS message,does not send the DISCONNECT message


no DISCONNECT


GRS;


ETSI


6.2.3.9.3 Receipt of Circuit Group blocking message (CGB) with the indication "hardwarefailure oriented"






Test purpose: Ensure that the SUT in state N9, having sent the ACM message, on receipt of a CGBmessage with the Circuit group supervision message type set to "hardware failure oriented",











Test purpose: Ensure that the SUT in state N7, having sent the ACM message, on receipt of a CGBmessage with the Circuit group supervision message type set to "hardware failure oriented",

















ETSI


















Test purpose: Ensure that the SUT in Idle state, on receipt of a CGB message with the Circuit groupsupervision message type set to "hardware failure oriented",






6.2.3.10 DSS1 Data link reset and Data Link failure procedures



ETS 300 356-1 [5], clause 2.2TSS reference: ISUP-DSS1/Basic call/DSS1 Data link reset and Data Link failure proceduresISDN selection


criteria:Test purpose: Ensure that the SUT in state N25, on receipt of a data link reset primitive

(DL-ESTABLISH-INDICATION)sends a DISCONNECT message with the cause value set to "temporary failure (41)" and

sends a REL message with the cause value set to "temporary failure (41)";ISDN Parameter

values:DISCONNECT; cause value: temporary failure (41)


REL; cause value: temporary failure (41)

Comments: ISDN DL-ESTABLISH IND -> SUT -> REL ISUP -> DISCONNECT ISDN

ETSI







(DL-ESTABLISH-INDICATION)does not send a DISCONNECT message and REL message






















ETSI









DL-RELEASE





















DL-RELEASE




ETSI






criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a data link failure primitive (DL-RELEASE),

sends DL-ESTABLISH INDICATION primitive, after expire of timer T309 without data linkre-establishment



DL-RELEASEDL-ESTABLISH IND;




6.2.3.11 Release by the exchange



ETS 300 356-1 [5], clause 2.4.3TSS reference: ISUP-DSS1/Basic call/Release by the exchange/ISDN selection

criteria:point-to-point configuration [A.1/R.7.1]


Test purpose: Ensure that the SUT in state N6, having sent the SETUP message, at expire of timer T303without response to the SETUP message

sends a REL message with the cause parameter set to "no user responding (18)" and aDISCONNECT message with the cause information element set to "recovery on timer expiry(102)".


SETUP;DISCONNECT; Cause information element: recovery on timer expiry (102)


IAM;REL; Cause parameter: no user responding (18)

Comments: SUT -> REL ISUP + DISCONNECT ISDN




criteria:multipoint configuration [A.1/R.7.2]


Test purpose: Ensure that the SUT in state N6, having sent the SETUP message via the broadcast datalink, at expire of timer T303 without response to the SETUP message

sends a REL message with the cause parameter set to "no user responding (18)" anddoes not send any message on the ISDN side.


SETUP;


IAM;REL; Cause parameter: no user responding (18)


ETSI







Test purpose: Ensure that the SUT in state N9, having received the CALL PROCEEDING message, atexpire of timer T310 without response to the CALL PROCEEDING message (no ALERTING,CONNECT, or DISCONNECT message)

sends a REL message with the cause parameter set to "no user responding (18)" and aDISCONNECT message with the cause information element set to "recovery on timer expiry(102)".


SETUP;CALL PROCEEDING;DISCONNECT; Cause information element: recovery on timer expiry (102)


IAM;(ACM; message present in case of ISDN overlap sending)REL; Cause parameter: no user responding (18)







Test purpose: Ensure that the SUT in state N9 in broadcast data link, having received the CALLPROCEEDING message, at expire of timer T310 without response to the CALL PROCEEDINGmessage (no ALERTING, CONNECT, or DISCONNECT message)

sends a REL message with the cause parameter set to "no user responding (18)" and aRELEASE message with the cause information element set to "recovery on timer expiry(102)".


SETUP;CALL PROCEEDING;RELEASE; Cause information element: recovery on timer expiry (102)


IAM;(ACM; message present in case of ISDN overlap sending)REL; Cause parameter: no user responding (18)


ETSI







Test purpose: Ensure that the SUT in state N7, having received the ALERTING message, at expire oftimer T301 without response to the ALERTING message (CONNECT, or DISCONNECTmessage)

sends a REL message with the cause parameter set to "user alerting, no answer (19)" anda DISCONNECT message with the cause information element set to "recovery on timerexpiry (102)".


SETUP;ALERTING;DISCONNECT; Cause information element: recovery on timer expiry (102)


IAM;ACM;REL; Cause parameter: user alerting, no answer (19)







Test purpose: Ensure that the SUT in state N7 on broadcast data link, having received the ALERTINGmessage, at expire of timer T301 without response to the ALERTING message (CONNECT, orDISCONNECT message)

sends a REL message with the cause parameter set to "user alerting, no answer (19)" anda RELEASE message with the cause information element set to "recovery on timer expiry(102)".


SETUP;ALERTING;RELEASE; Cause information element: recovery on timer expiry (102)


IAM;ACM;REL; Cause parameter: user alerting, no answer (19)


6.2.3.12 Receipt of the Release Complete message (RLC)



TSS reference: ISUP-DSS1/Basic call/Receipt of the Release Complete message (RLC)ISDN selection



Test purpose: Ensure that the SUT after receiving the IAM where the ISUP indicator is set to "ISUP isused all the way", the ISDN access indicator is set to "ISDN", sends out a SETUPmessage and on receipt of the RLC message

sends a DISCONNECT at the DSS1 side and a REL message at the ISUP sideISDN Parameter

values:SETUPDISCONNECT;


IAM; ISUP indicator: ISUP used all the wayRLC;REL;

Comments: ISUP RLC -> SUT -> DISCONNECT ISDN

ETSI







Test purpose: Ensure that the SUT after receiving the IAM where the ISUP indicator is set to "ISUP isused all the way", the ISDN access indicator is set to "ISDN", sends out a SETUPmessage, receives a SETUP ACKNOWLEDGE message and on receipt of a REL message

sends a DISCONNECT at the DSS1 side and a REL message at the ISUP side.ISDN Parameter

values:SETUP;SETUP ACKNOWLEDGE;DISCONNECT;


IAM; IAM; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNRLC;REL;







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message, and on receipt of a SAM message followed by a RLCmessage

sends a INFORMATION message followed by a DISCONNECT at the DSS1 side and aREL message at the ISUP side.


SETUP;SETUP ACKNOWLEDGE;INFORMATIONDISCONNECT;


IAM;SAM;RLC;RE;







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a RLC message


values:SETUP;CALL PROCEEDING;DISCONNECT;


IAM;ACM;RLC;REL;


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message followed by a PROGRESS message with a progressindicator where the progress description value is set to PI_VALUE, remains in state N9,sends out an ACM Message where the CPS indicator is set to "no indication" followed by aCPG and on receipt of a RLC message


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)DISCONNECT


IAM;ACM;CPG; Event indicator: progressRLC;REL;







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING message, sends out an ACMMessage where the CPS indicator is set to "subscriber free" and on receipt of a RLC


values:SETUP;SETUP ACKNOWLEDGE;ALERTING;DISCONNECT;


IAM;ACM;RLC;REL;


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to alerting and on receipt of a RLC message,


values:SETUP;CALL PROCEEDING;ALERTING;DISCONNECT;


ACM; CPS indicator: no indicationCPG; Event indicator: alertingRLC;REL;







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to progress, and on receipt of a ALERTING Message goes to state N7,sends out a CPG message where the Event indicator is set to alerting and on receipt of aRLC message


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;DISCONNECT;


IAM;ACM;CPG; Event indicator: progressCPG; Event indicator: alertingRLC;REL;


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to progress, and on receipt of a RLC message


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS; progress indicator PI_VALUE (PIXIT)DISCONNECT;


IAM; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNACM; CPS indicator: no indicationCPG; Event indicator: alertingCPG; Event indicator: progressRLC;REL;







CALL PROCEEDING message, sends out an ACM Message where the CPS indicator isset to "no indication" receives a CONNECT message, sends out an ANM message and onreceipt of a RLC message


values:SETUP;CALL PROCEEDING;CONNECT;DISCONNECT;


IAM; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNACM; CPS indicator: no indicationANM;RLC;REL;


ETSI







CONNECT message, sends out an CON message and on receipt of a RLC messagesends a DISCONNECT at the DSS1 side and a REL message at the ISUP side.


SETUP;CONNECT;DISCONNECT;


IAM; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNCONNECT;RLC;REL;



ISUP ref. to:ETS 300 356-1 [5], clause 2.9.5.1




PIXIT Automatic ACM

Test purpose: Ensure that the SUT in state N6, having sent automatically the ACM message, onreceipt of the RLC message


values:DISCONNECT;


RLC;REL;





criteria:Coincidence S T reference points [A.1/R.3.2]AND called party addressing information split across, and send in, SETUP andINFORMATION messages [A.62/MCn2.2]


Test purpose: Ensure that the SUT after receiving the IAM where the ISUP indicator is set to "ISUP isused all the way", the ISDN access indicator is set to "ISDN", sends out a SETUPmessage, receives a SETUP ACKNOWLEDGE message and on receipt of a REL message

sends a RELEASE at the DSS1 side and a REL message at the ISUP side.ISDN Parameter

values:SETUP;SETUP ACKNOWLEDGE;RELEASE;


IAM; IAM; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNRLC;REL;

Comments: ISUP RLC -> SUT -> RELEASE ISDN

ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message receives aSETUP ACKNOWLEDGE message, and on receipt of a SAM message followed by a RLCmessage

sends a INFORMATION message followed by a RELEASE at the DSS1 side and a RELmessage at the ISUP side.


SETUP;SETUP ACKNOWLEDGE;INFORMATIONRELEASE;


IAM;SAM;RLC;RE;





criteria:Coincidence S T reference points [A.1/R.3.2]


Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication" and on receipt of a RLC message


values:SETUP;CALL PROCEEDING;RELEASE;


IAM;ACM;RLC;REL;


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message followed by a PROGRESS message with a progressindicator where the progress description value is set to PI_VALUE, remains in state N9,sends out an ACM Message where the CPS indicator is set to "no indication" followed by aCPG and on receipt of a RLC message


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)RELEASE


IAM;ACM;CPG; Event indicator: progressRLC;REL;







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aSETUP ACKNOWLEDGE message followed by a ALERTING message, sends out an ACMMessage where the CPS indicator is set to "subscriber free" and on receipt of a RLC


values:SETUP;SETUP ACKNOWLEDGE;ALERTING;RELEASE;


IAM;ACM;RLC;REL;


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to alerting and on receipt of a RLC message,


values:SETUP;CALL PROCEEDING;ALERTING;RELEASE;


ACM; CPS indicator: no indicationCPG; Event indicator: alertingRLC;REL;







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", receives a PROGRESS message with a progress indicator where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to progress, and on receipt of a ALERTING Message goes to state N7,sends out a CPG message where the Event indicator is set to alerting and on receipt of aRLC message


values:SETUP;CALL PROCEEDING;PROGRESS; progress indicator: PI_VALUE (PIXIT)ALERTING;RELEASE;


IAM;ACM;CPG; Event indicator: progressCPG; Event indicator: alertingRLC;REL;


ETSI







Test purpose: Ensure that the SUT after receiving the IAM sends out a SETUP message, receives aCALL PROCEEDING message, sends out an ACM Message where the CPS indicator is setto "no indication", on receipt of a ALERTING Message, sends out a CPG message wherethe Event indicator is set to alerting, on receipt of a PROGRESS message where theprogress description value is set to PI_VALUE, sends out a CPG message where the Eventindicator is set to progress, and on receipt of a RLC message


values:SETUP;CALL PROCEEDING;ALERTING;PROGRESS; progress indicator PI_VALUE (PIXIT)RELEASE;


IAM; ISUP indicator: ISUP is used all the wayISDN access indicator: ISDNACM; CPS indicator: no indicationCPG; Event indicator: alertingCPG; Event indicator: progressRLC;REL;


6.2.4 Procedures for point-to-multipoint configurations with more than oneterminal attached

For this group, an additional PTC3 is connected to the same basic access as the PTC1. Thus messages that are sent tothe PTC1 via the broadcast data link will be received at PTC3 via PCO L3 as well. Both the PTC1 and PTC3 will sendmessages on the same access using the same call reference value. A distinction between the two message flows relatedto the PCOs L1 and L3 can still be made, as they use different data link entities. This distinction between the twoparallel test components is expressed by mentioning the Connection Endpoint Suffix (CES) on which the singlemessages are sent. CES1 is related to the PTC1, CES2 is related to PTC3.

6.2.4.1 Sending of the Call progress message (CPG)

From Call state N09.



TSS reference: ISUP-DSS1/Basic call/Point-to-multipoint configuration/Sending of the CPGISDN selection


criteria:Test purpose: Ensure that the SUT in call state N9, having sent the ACM message and having

received a CALL PROCEEDING message for CES1 without any Progress indicatorelement,

on receipt of a CALL PROCEEDING message for CES2 without Progress indicatorelement, sends no message.

ISDN1 Parametervalues:

CALL PROCEEDING: no progress indicator;





ETSI







received of a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of a CALL PROCEEDING message for CES2 with the progress indicator set

to PI_VALUE, sends the CPG message with the event indicator set to "Progress" and theATP containing the progress indicator set to PI_VALUE.




CALL PROCEEDING; progress indicator: PI_VALUE;










received a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of a CALL PROCEEDING message for CES2 with the progress indicator set

to PI_VALUE, sends no message.ISDN1 Parameter

values:CALL PROCEEDING: no progress indicator;





Values and additional selection criteria for test purposes TP314003VA_01 PI_VALUE = Originating address is non-ISDN (#3)VA_02 PI_VALUE = Call has returned to the ISDN (#4)VA_03 PI_VALUE = In-band information or appropriate pattern now available (#8)

ETSI







received a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of a CALL PROCEEDING message without progress indicator element

followed by a PROGRESS message for CES2 with the progress indicator set toPI_VALUE, sends the CPG message with the event indicator set to "Progress" and ATPcontaining the progress indicator set to PI_VALUE.




CALL PROCEEDING: no progress indicator;PROGRESS; progress indicator: PI_VALUE


CPG; event indicator: "Progress"ATP progress indicator: PI_VALUE


Values and additional selection criteria for test purposes TP314004VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)VA_03 PI_VALUE = Call has returned to the ISDN (#4)






received a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of a CALL PROCEEDING message without progress indicator element

followed by a PROGRESS message for CES2 with the progress indicator set toPI_VALUE, sends no message.




CALL PROCEEDING: no progress indicator;PROGRESS; progress indicator: PI_VALUE;



Values and additional selection criteria for test purposes TP314005VA_01 PI_VALUE = Originating address is non-ISDN (#3)VA_02 PI_VALUE = In-band information or appropriate pattern now available (#8)

ETSI







received a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of an ALERTING message for CES2 without progress indicator element,

sends the CPG message with the event indicator set to "alerting".ISDN1 Parameter



ALERTING: no progress indicator;


CPG; event indicator: "alerting"







received a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of an ALERTING message for CES2 with the progress indicator set to "in-

band information or appropriate pattern now available (#8)", sends the CPG message withthe event indicator set to "alerting".




ALERTING; progress indicator: "in-band information or appropriate pattern now available(#8)";


CPG; event indicator: "alerting"







received a CALL PROCEEDING message for CES1 without progress indicator element,on receipt of an ALERTING message for CES2 with the progress indicator set to

PI_VALUE , sends the CPG message with the event indicator set to "alerting" and the ATPcontaining the progress indicator set to PI_VALUE.




ALERTING: PI_VALUE


CPG; event indicator: "alerting"ATP progress indicator: PI_VALUE


ETSI


Values and additional selection criteria for test purposes TP314008VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)VA_03 PI_VALUE = Call has returned to the ISDN (#4)





criteria:PIXIT automatic ACM

Test purpose: Ensure that the SUT in call state N6, having automatically sent the ACM message, onreceipt of a CALL PROCEEDING message for CES1 with the progress indicator set to"Call is not end-to-end ISDN (#1)" and of a CALL PROCEEDING message for CES2 withthe progress indicator set to "Destination address is non-ISDN (#2)",

sends a CPG message with the event indicator set to "Progress" and the ATPcontaining the progress indicator set to "Call is not end-to-end ISDN (#1)" and sends aCPG message with the event indicator set to "Progress" and the ATP containing theprogress indicator set to "Destination address is non-ISDN (#2)".


CALL PROCEEDING; progress indicator: Call is not end-to-end ISDN (#1)


CALL PROCEEDING; progress indicator: Destination address is non-ISDN (#2)


CPG; event indicator: "progress"ATP progress indicator: Destination address is non-ISDN (#2)






criteria:Test purpose: Ensure that the SUT in call state N9, having sent the ACM message on receipt of a

CALL PROCEEDING message for CES1 with the progress indicator set to "Call is notend-to-end ISDN (#1)",

on receipt of a CALL PROCEEDING message for CES2 with the progress indicator setto "Destination address is non-ISDN (#2)", sends the CPG message with the eventindicator set to "Progress" and the ATP containing the progress indicator set to"Destination address is non-ISDN (#2)".


CALL PROCEEDING; progress indicator: Call is not end-to-end ISDN (#1)






ETSI





criteria:PIXIT automatic ACM


Test purpose: Ensure that the SUT in call state N6, having sent automatically the ACM message, onreceipt of a CALL PROCEEDING message for CES1 with the progress indicator set to"Destination address is non-ISDN (#2)" and a CALL PROCEEDING message withoutprogress indicator element followed by a PROGRESS message for CES2 with theprogress indicator set to PI_VALUE,

sends a CPG message with the event indicator set to "Progress" and the ATPcontaining the progress indicator set to "Destination address is non-ISDN (#2)" and sendsthe CPG message with the event indicator set to "Progress" and the ATP containing theprogress indicator set to PI_VALUE.






CPG; event indicator: "progress"ATP progress indicator: PI_VALUE






criteria:Test purpose: Ensure that the SUT in call state N9, having sent the ACM message on receipt of a

CALL PROCEEDING message for CES1 with the progress indicator set to "Destinationaddress is non-ISDN (#2)",

on receipt of a CALL PROCEEDING message without progress indicator elementfollowed by a PROGRESS message for CES2 with the progress indicator set toPI_VALUE, sends the CPG message with the event indicator set to "Progress" and theATP containing the progress indicator set to PI_VALUE.








Values and additional selection criteria for test purposes TP314011 and TP314012VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Call has returned to the ISDN (#4)

ETSI







criteria:Test purpose: Ensure that the SUT in call state N7, having sent the ACM message, and having sent

the CPG message on receipt of an ALERTING message for CES1 without progressindicator element,

on receipt of a CALL PROCEEDING message for CES2 without progress indicator,sends no message.


ALERTING; no progress indicator;











on receipt of an ALERTING message for CES2 without progress indicator, sends nomessage.













on receipt of an ALERTING message for CES2 with the progress indicator set toPI_VALUE, sends no message.




ALERTING; progress indicator: PI_VALUE;



ETSI


Values and additional selection criteria for test purposes TP314015VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Destination address is non-ISDN (#2)VA_03 PI_VALUE = Call has returned to the ISDN (#4)VA_04 PI_VALUE = In-band information or appropriate pattern now available (#8)







on receipt of a CALL PROCEEDING message for CES2 with the progress indicator setto PI_VALUE, sends the CPG message with the event indicator set to "Progress" and theATP containing the progress indicator set to PI_VALUE.















on receipt of a CALL PROCEEDING message for CES2 with the progress indicator setto PI_VALUE, sends no message.








ETSI








on receipt of a CALL PROCEEDING message followed by a PROGRESS message forCES2 with the progress indicator set to PI_VALUE, sends the CPG message with theevent indicator set to "Progress" and the ATP containing the progress indicator set toPI_VALUE.















on receipt of a CALL PROCEEDING message without progress indicator elementfollowed by a PROGRESS message for CES2 with the progress indicator set toPI_VALUE, sends no message.








ETSI








on receipt of a ALERTING message without progress indicator element followed by aPROGRESS message for CES2 with the progress indicator set to PI_VALUE, sends theCPG message with the event indicator set to "Progress" and the ATP containing theprogress indicator set to PI_VALUE.


ALERTING: without any progress indicator;


ALERTING: no progress indicator;PROGRESS; progress indicator: PI_VALUE;











on receipt of a ALERTING message without progress indicator element followed by aPROGRESS message for CES2 with the progress indicator set to PI_VALUE, sends nomessage.




ALERTING: no progress indicator;PROGRESS; progress indicator: PI_VALUE;




ETSI







the CPG message on receipt of an ALERTING message for CES1 with the progressindicator set to "Call is not end-to-end ISDN (#1)",

on receipt of a CALL PROCEEDING message for CES2 with the progress indicator setto "Destination address is non-ISDN (#2)", sends the CPG message with the eventindicator set to "Progress" and the ATP containing the progress indicator set to"Destination address is non-ISDN (#2)".













the CPG message on receipt of an ALERTING message for CES1 with the progressindicator set to "Destination address is non-ISDN (#2)",



ALERTING; progress indicator: Destination address is non-ISDN (#2)






Values and additional selection criteria for test purposes TP314023VA_01 PI_VALUE = Call is not end-to-end ISDN (#1)VA_02 PI_VALUE = Call has returned to the ISDN (#4)

ETSI







the CPG message on receipt of an ALERTING message for CES1 with the progressindicator set to "Call is not end-to-end ISDN (#1)",









Values and additional selection criteria for test purposes TP314024VA_01 PI_VALUE = Destination address is non-ISDN (#2)VA_02 PI_VALUE = Call has returned to the ISDN (#4)

6.2.4.2 Sending of the Answer message (ANM)




TSS reference: ISUP-DSS1/Basic call/Point-to-multipoint configuration/Sending of the ANMISDN selection




on receipt of a CONNECT message for CES2, sends an ANM message.ISDN1 Parameter



CONNECT;


ANM;


ETSI




ETS 300 356-1 [5], clause 2.1.7TSS reference: ISUP-DSS1/Basic call/Point-to-multipoint configuration/Sending of the ANMISDN selection




on receipt of a CONNECT message with the progress indicator set to PI_VALUE forCES2, sends an ANM message with ATP containing the progress indicator set toPI_VALUE.













received a CALL PROCEEDING message for CES1,on receipt of a CONNECT message with the low layer capability set to LLC_VALUE for

CES2, sends an ANM message with ATP containing the low layer capability set toLLC_VALUE.


CALL PROCEEDING;




ANM; ATP LLC: LLC_VALUE (PIXIT)





TSS reference: ISUP-DSS1/Basic call/Point-to-multipoint configuration/Sending of the ANMISDN selection



the CPG message on receipt of an ALERTING message for CES1 without any Progressindicator element,

on receipt of a CONNECT message for CES2, sends an ANM message.ISDN1 Parameter

values:ALERTING: no progress indicator;


CONNECT;


ANM;


ETSI







the CPG message on receipt of an ALERTING message for CES1 without any Progressindicator element,

on receipt of a CONNECT message with the progress indicator set to PI_VALUE forCES2, sends an ANM message with ATP containing the progress indicator set toPI_VALUE.













the CPG message on receipt of an ALERTING message for CES1,on receipt of a CONNECT message with the low layer capability set to LLC_VALUE for

CES2, sends an ANM message with ATP containing the low layer capability set toLLC_VALUE.


ALERTING;




ANM; ATP LLC: LLC_VALUE (PIXIT)


ETSI


6.2.4.3 Receipt of call clearing messages during call establishment

Call state N06.


ISUP ref. to:EN 300 899-1 [1], clause 3.1.1.8

TSS reference: ISUP-DSS1/Basic call/Point-to-multipoint configuration/Call clearingISDN selection


criteria:Test purpose: Ensure that the SUT in call state N6, on receipt of a RELEASE COMPLETE message for

CES1 with cause value "user busy #17",on receipt of a RELEASE COMPLETE message for CES2 with cause value "call

rejected #21", sends a REL message with cause value "user busy #17".ISDN1 Parameter

values:RELEASE COMPLETE: cause value: user busy #17;


RELEASE COMPLETE: cause value: call rejected #21;


REL: cause value: user busy #17;


Call state N09.






received a CALL PROCEEDING message for CES1,on receipt of a RELEASE COMPLETE message for CES2, sends no message.


CALL PROCEEDING;


RELEASE COMPLETE;








received CALL PROCEEDING messages for CES1 and CES2,on receipt of a DISCONNECT message with cause value "user busy #17" for CES2

followed by a DISCONNECT message with cause value "call rejected #21" for CES1,sends a REL message with cause value "user busy #17".


CALL PROCEEDING;DISCONNECT: cause value: call rejected #21;


CALL PROCEEDING;DISCONNECT: cause value: user busy #17;


REL: cause value: user busy #17;


ETSI


Call state N07.






the CPG message on receipt of an ALERTING message for CES1,on receipt of a RELEASE COMPLETE message for CES2, sends no message.


CALL PROCEEDING;


RELEASE COMPLETE;








the CPG message on receipt of an ALERTING message for CES1,on receipt of a CALL PROCEEDING message followed by a DISCONNECT message

with cause value "user busy #17" for CES2, and on receipt of a DISCONNECT messagewith cause value "call rejected #21" for CES1, sends a REL message with cause value"call rejected #21".






REL: cause value: call rejected #21;







the CPG message on receipt of an ALERTING message for CES1,on receipt of an ALERTING message followed by a DISCONNECT message with cause

value "user busy #17" for CES2, and on receipt of a DISCONNECT message with causevalue "call rejected #21" for CES1, sends a REL message with cause value "call rejected#21".






REL: cause value: call rejected #21;


ETSI


6.2.5 Interworking from ISUP to Non-ISDN (Incoming Call)

6.2.5.1 Sending of the Ringing


TSS reference: ISUP-DSS1/Basic call/Sending of the RingingISUP selection

criteria:Test purpose: Ensure that the SUT on receipt of the IAM message containing all the information

required to go on with the callsends a call set-up indication


IAM;

Comments:




required to go on with the call and the connection indicator set to "continuity checkrequired on this circuit"

does not send the call set-up indication until is has received the COT message withthe continuity indicator set to "continuity check successful".


IAM; connection indicator: continuity check required on this circuitCOT; continuity indicator: continuity check successful

Comments:




required to go on with the call and the connection indicator set to "continuity checkrequired on a previous circuit"

does not send the call set-up indication until is has received the COT message withthe continuity indicator set to "continuity check successful".


IAM; connection indicator: continuity check required on a previous circuitCOT; continuity indicator: continuity check successful

Comments:

6.2.5.2 Receipt of the Subsequent address message (SAM)



criteria:Test purpose: Ensure that the SUT on receipt of the IAM message followed by SAM messages

containing all the information required to go on with the callsends a call set-up indication


IAM;SAM

Comments:

ETSI


6.2.5.3 Sending of the Address complete message (ACM)



criteria:Test purpose: Ensure that the SUT on detection that the complete called party number has been

receivedsends an ACM message with the CPS indicator set to "no indication", the

Interworking indicator set to "no interworking encountered", the ISUP indicator set to"ISUP used all the way", the ISDN access indicator set to "non-ISDN"


ACM; CPS indicator: no indicationInterworking indicator: no interworking encounteredISUP indicator: ISUP used all the wayISDN access indicator: non-ISDN

Comments:



criteria:Test purpose: Ensure that the SUT on detection that the subscribed is free

sends an ACM message with the CPS indicator set to "subscriber free", theInterworking indicator set to "no interworking encountered", the ISUP indicator set to"ISUP used all the way", the ISDN access indicator set to "non-ISDN"


ACM; CPS indicator: subscriber freeInterworking indicator: no interworking encounteredISUP indicator: ISUP used all the wayISDN access indicator: non-ISDN

Comments:



criteria:Test purpose: Ensure that the SUT on detection in case of call failure that a special in-band tone or

announcement has to be returned to the calling partysends an ACM message with the CPS indicator set to "no indication", the

Interworking indicator set to "no interworking encountered", the ISUP indicator set to"ISUP used all the way", the ISDN access indicator set to "non-ISDN" and the OBCI in-band set to "in-band information or an appropriate pattern is now available"


ACM; CPS indicator: no indicationInterworking indicator: no interworking encounteredISUP indicator: ISUP used all the wayISDN access indicator: non-ISDNOBCI in-band: in-band information or an appropriate pattern is now available

Comments:

ETSI


6.2.5.4 Sending of the Call progress message (CPG)


TSS reference: ISUP-DSS1/Basic call/Sending of the Call progress message (CPG)ISUP selection

criteria:Test purpose: Ensure that the SUT, having sent the ACM message, on detection that the subscriber

is freesends a CPG message with event information set to "Alerting"


CPG; event information: Alerting

Comments:


TSS reference: ISUP-DSS1/Basic call/Sending of the Call progress message (CPG)ISUP selection

criteria:Test purpose: Ensure that the SUT, having sent the ACM message, on detection that an in-band

tone or announcement has to be returned to the calling partysends a CPG message with event information set to "in-band information or an

appropriate pattern is now available"ISUP Parameter

values:CPG; event information: in-band information or an appropriate pattern is now available

Comments:

6.2.5.5 Sending of the answer message (ANM)


TSS reference: ISUP-DSS1/Basic call/Sending of the answer message (ANM)ISUP selection

criteria:Test purpose: Ensure that the SUT, having sent the ACM message, on detection of the Off-hook

condition on the non-ISDN sidesends a ANM message


ANM;

Comments:



TSS reference: ISUP-NON ISDN/Basic call/Receipt of the Release message (RELISUP selection

criteria:Test purpose: Ensure that the SUT, having sent the IAM message, on receipt of the REL message

sends a the message indicating the release procedureISUP Parameter

values:IAM;REL;

Comments:

ETSI




criteria:Test purpose: Ensure that the SUT, having sent the SAM message, on receipt of the REL message


values:SAM;REL;

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the ACM message, on receipt of the REL message


values:IAM;ACM;REL;

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the CPG message, on receipt of the REL message


values:IAM;CPG;REL;

Comments:



criteria:Test purpose: Ensure that the SUT, having sent the ANM message, on receipt of the REL message


values:IAM;ANM;REL;

Comments:

6.2.5.7 Sending of the Suspend message (SUS) network initiated


TSS reference: ISUP-NON ISDN/Basic call/Sending of the Suspend message (SUS) network initiatedISUP selection

criteria:Test purpose: Ensure that the SUT, during the conversation/data phase, on receipt of the on-hook

conditionsends the SUS message


SUS;

Comments:

ETSI


6.2.5.8 Sending of the Resume message (RES) network initiated


TSS reference: ISUP-NON ISDN/Basic call/Sending of the Resume message (RES) network initiatedISUP selection

criteria:Test purpose: Ensure that the SUT, during the conversation/data phase having sent the SUS

message, on receipt of the off-hook conditionsends the RES message


SUS;RES;

Comments:

6.3 Test purposes for the Supplementary Services

6.3.1 Interworking from DSS1 to ISUP (Outgoing Call)

6.3.1.1 Calling Line Identification Presentation (CLIP)

ISDN selection criteria: CLIR not subscribed.

6.3.1.1.1 Special arrangement applies

ISDN selection criteria: Special arrangement applies.

TP501101 ISDN reference:EN 300 092-1 [13]

ISUP reference:EN 300 899-1 [1], clause 2.1.2.3.1

TSS reference: DSS1-ISUP/SS/CLIP/Special ArrangementISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with an invalid

Calling party number information element,sends an IAM message with the Calling party number parameter coded

Address signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided

and without the Generic number parameter.ISDN Parameter

values:SETUP;invalid Calling party number information element


IAM;Calling party number parameterAddress signals = PIXITNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameter not present


ETSI







Calling party number information element but with a valid Calling party subaddressinformation element,

sends an IAM message with the Calling party number parameter codedAddress signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided,

without the Generic number parameterand including the subaddress information in the Access transport parameter.


SETUP;invalid Calling party number information elementCalling party subaddress information element


IAM;Calling party number parameterAddress signals = PIXITNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameter not presentAccess transport parameter including the subaddress information






criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message without a Calling

party number information element,sends an IAM message with the Calling party number parameter coded



values:SETUP;Calling party number information element not present




ETSI







party number information element, but with a valid Calling party subaddressinformation element,

sends an IAM message with the Calling party number parameter codedAddress signals = Default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided,



SETUP;Calling party number information element not presentCalling party subaddress information element




ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Calling party

number information element codedType of number = national number,Numbering plan identification = ISDN_NPI,

sends an IAM message with the Calling party number parameter codedAddress signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided

and with the Generic number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, not screened.


SETUP;Calling party number information elementType of number = '010'BNumbering plan identification = ISDN_NPINumber digits = PIXIT2


IAM;Calling party number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '00'B


ETSI







number information element codedType of number = national numberNumbering plan identification = ISDN_NPIand with a Calling party subaddress information element,


with the Generic number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, not screened

and including the subaddress information in the Access transport parameter.ISDN Parameter

values:SETUP;Calling party number information elementType of number = '010'BNumbering plan identification = ISDN_NPINumber digits = PIXIT2Calling party subaddress information element


IAM;Calling party number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '00'BAccess transport parameter including the subaddress information


ETSI







number information element codedType of number = international numberNumbering plan identification = ISDN_NPI,


and with the Generic number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, not screened.


SETUP;Calling party number information elementType of number = '001'BNumbering plan identification = ISDN_NPINumber digits = PIXIT2


IAM;Calling party number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '00'B


ETSI







number information element codedType of number = international numberNumbering plan identification = ISDN_NPIand with a Calling party subaddress information element,


with the Generic number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, not screened


values:SETUP;Calling party number information elementType of number = '001'BNumbering plan identification = ISDN_NPINumber digits = PIXIT2Calling party subaddress information element


IAM;Calling party number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '00'BAccess transport parameter including the subaddress information


Values for the test purposes TP501105 - TP501108VA_01 ISDN_NPI = ISDN/telephony numbering plan,

'0001'B-

VA_02 ISDN_NPI = unknown, '0000'B -

ETSI


6.3.1.1.2 Special arrangement does not apply

ISDN selection criteria: Special arrangement does apply.



TSS reference: DSS1-ISUP/SS/CLIP/No Special ArrangementISDN selection



Calling party number information element,sends an IAM message with the Calling party number parameter coded



values:SETUP;invalid Calling party number information element





ISUP reference:EN 300 899-1 [1], clause 2.1.2.3.2;

ETS 300 356-1 [5], clause 2.1TSS reference: DSS1-ISUP/SS/CLIP/No Special ArrangementISDN selection



Calling party number information element but with a valid Calling party subaddressinformation element,




SETUP;invalid Calling party number information elementCalling party subaddress information element




ETSI







party number information element,sends an IAM message with the Calling party number parameter coded



values:SETUP;Calling party number information element not present









party number information element, but with a valid Calling party subaddressinformation element,




SETUP;Calling party number information element not presentCalling party subaddress information element




ETSI





criteria:Failure of the screening function can be provoked


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Calling partynumber information element, when a failure of the screening function occurs,



values:SETUP;Calling party number information element









Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Calling partynumber information element and with a valid Calling party subaddress informationelement, when a failure of the screening function occurs,




SETUP;Calling party number information elementCalling party subaddress information element




ETSI







number information element codedType of number = subscriber numberNumbering plan identification = ISDN_NPINumber digits = correct complete subscriber number,

sends an IAM message with the Calling party number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed


values:SETUP;Calling party number information elementType of number = '100'BNumbering plan identification = ISDN_NPINumber digits = PIXIT









number information element codedType of number = subscriber numberNumbering plan identification = ISDN_NPINumber digits = correct complete subscriber numberand with a Calling party subaddress information element,

sends an IAM message with the Calling party number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,

without the Generic number parameter,and including the subaddress information in the Access transport parameter.


SETUP;Calling party number information elementType of number = '100'BNumbering plan identification = ISDN_NPINumber digits = PIXITCalling party subaddress information element




ETSI







number information element codedType of number = national numberNumbering plan identification = ISDN_NPINumber digits = correct complete national number,

sends an IAM message with the Calling party number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed






ETSI







number information element codedType of number = national numberNumbering plan identification = ISDN_NPINumber digits = correct complete national numberand with a Calling party subaddress information element,

sends an IAM message with the Calling party number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,












number information element codedType of number = international numberNumbering plan identification = ISDN_NPINumber digits = correct complete international number,

sends an IAM message with the Calling party number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, verified and passed






ETSI







number information element codedType of number = international number,Numbering plan identification = ISDN_NPI,Number digits = correct complete international numberand with a Calling party subaddress information element,

sends an IAM message with the Calling party number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, verified and passed,







ETSI







number information element codedType of number = unknownNumbering plan identification = ISDN_NPINumber digits = incomplete number,

sends an IAM message with the Calling party number parameter codedAddress signals = completion of the number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed




IAM;Calling party number parameterAddress signals = PIXIT completedNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '01'BGeneric number parameter not present







number information element codedType of number = unknownNumbering plan identification = ISDN_NPINumber digits = incomplete numberand with a Calling party subaddress information element,

sends an IAM message with the Calling party number parameter codedAddress signals = completion of the number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,





IAM;Calling party number parameterAddress signals = PIXIT completedNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '01'BGeneric number parameter not presentAccess transport parameter including the subaddress information


ETSI



'0001'B-


6.3.1.2 Calling Line Identification Restriction (CLIR)

ISDN selection criteria: CLIR subscribed.




ISUP reference:EN 300 899-1 [1], clause 2.1.2.4

TSS reference: DSS1-ISUP/SS/CLIR/Special ArrangementISDN selection

criteria:CLIR permanent mode


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a valid Callingparty number information element,

sends an IAM message with the Calling party number parameter and the Genericnumber parameter coded

Address presentation restricted indicator = presentation restricted.ISDN Parameter



IAM;Calling party number parameter and Generic number parameterAddress presentation restricted indicator = '01'B





criteria:CLIR temporary mode, default setting = restricted


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a valid Callingparty number information element codedPresentation indicator = ISDN_PRI,


Address presentation restricted indicator = ISUP_PRI.ISDN Parameter

values:SETUP;Calling party number information elementPresentation indicator = ISDN_PRI


IAM;Calling party number parameter and Generic number parameterAddress presentation restricted indicator = ISUP_PRI


Values for the test purpose TP502102VA_01 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'BVA_02 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'B

ETSI







Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a valid Callingparty number information element not including the optional octet 3a (screening andpresentation indicator),


Address presentation restricted indicator = presentation restricted.ISDN Parameter

values:SETUP;Calling party number information elementPresentation indicator not present







criteria:CLIR temporary mode, default setting = allowed




Address presentation restricted indicator = ISUP_PRI.ISDN Parameter



IAM;Calling party number parameter and Generic number parameterAddress presentation restricted indicator = ISUP_PRI


Values for the test purpose TP502104VA_01 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'BVA_02 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'B

ETSI









Address presentation restricted indicator = presentation allowed.ISDN Parameter






ISDN selection criteria: Special arrangement does not apply.



TSS reference: DSS1-ISUP/SS/CLIR/No Special ArrangementISDN selection

criteria:CLIR permanent mode


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a valid Callingparty number information element,

sends an IAM message with the Calling party number parameter codedAddress presentation restricted indicator = presentation restricted




IAM;Calling party number parameterAddress presentation restricted indicator = '01'BGeneric number parameter not present


ETSI








sends an IAM message with the Calling party number parameter codedAddress presentation restricted indicator = ISUP_PRI




IAM;Calling party number parameterAddress presentation restricted indicator = ISUP_PRIGeneric number parameter not present


Values for the test purpose TP502202VA_01 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'BVA_02 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'B







sends an IAM message with the Calling party number parameter codedAddress presentation restricted indicator = presentation restricted






ETSI








sends an IAM message with the Calling party number parameter codedAddress presentation restricted indicator = ISUP_PRI




IAM;Calling party number parameterAddress presentation restricted indicator = ISUP_PRIGeneric number parameter not present


Values for the test purpose TP502204VA_01 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'BVA_02 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'B







sends an IAM message with the Calling party number parameter codedAddress presentation restricted indicator = presentation allowed






ETSI


6.3.1.3 Connected Line Identification Presentation (COLP)

6.3.1.3.1 COLP subscribed

ISDN selection criteria: COLP subscribed.

NOTE: The connected line identity request indicator in the Optional forward call indicators parameter in the IAMmessage is coded to "requested".

TP503101 ISDN reference:EN 300 097-1 [15], EN 300 098-1 [16]

ISUP reference:EN 300 899-1 [1], clauses 2.1.2.5, 2.1.2.6

TSS reference: DSS1-ISUP/SS/COLP/SubscribedISDN selection


criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a CON message with a Connected number

parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = ISUP_SIAddress signals includedand without the Generic number parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = ISDN_SINumber digits included.


CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = ISDN_SINumber digits = PIXIT


CON;Connected number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = ISUP_SIAddress signals = PIXITGeneric number parameter not present


ETSI







parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = ISUP_SIAddress signals included,without the Generic number parameter and with the connected subaddress in the Accesstransport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = ISDN_SINumber digits included

and with the Connected subaddress information element.ISDN Parameter

values:CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = ISDN_SINumber digits = PIXITConnected subaddress information element


CON;Connected number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = ISUP_SIAddress signals = PIXITGeneric number parameter not presentAccess transport parameter including the subaddress information


ETSI




TSS reference: DSS1-ISUP/SS/COLP/No SubscribedISDN selection


criteria:Test purpose: Ensure that the SUT in state N4, on receipt of an ANM message with a Connected

number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = ISUP_SIAddress signals includedand without the Generic number parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = ISDN_SINumber digits included.


CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = ISDN_SINumber digits = PIXIT


ANM;Connected number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = ISUP_SIAddress signals = PIXITGeneric number parameter not present


ETSI







number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = ISUP_SIAddress signals included,without the Generic number parameter and with the connected subaddress in the Accesstransport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = ISDN_SINumber digits included


values:CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = ISDN_SINumber digits = PIXITConnected subaddress information element


ANM;Connected number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = ISUP_SIAddress signals = PIXITGeneric number parameter not presentAccess transport parameter including the subaddress information


Values for the test purposes TP503101 - TP503104VA_01 ISDN_TON = national number, '010'B

ISDN_SI = user provided verified and passed,'01'B

ISUP_NAI = national number, '0000011'BISUP_SI = user provided verified and passed,'01'B

VA_02 ISDN_TON = national number, '010'BISDN_SI = network provided, '11'B

ISUP_NAI = national number, '0000011'BISUP_SI = network provided, '11'B

VA_03 ISDN_TON = international number, '001'BISDN_SI = user provided verified and passed,'01'B

ISUP_NAI = international number, '0000100'BISUP_SI = user provided verified and passed,'01'B

VA_04 ISDN_TON = international number, '001'BISDN_SI = network provided, '11'B

ISUP_NAI = international number, '0000100'BISUP_SI = network provided, '11'B

ETSI







parameter codedAddress presentation restricted parameter = presentation allowedand with the Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not verifiedAddress signals included,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included.


CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXIT


CON;Connected number parameterAddress presentation restricted parameter = '00'BGeneric number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXIT


ETSI







parameter codedAddress presentation restricted parameter = presentation allowedand with the Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not verifiedAddress signals includedand with the connected subaddress in the Access transport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included


values:CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXITConnected subaddress information element


CON;Connected number parameterAddress presentation restricted parameter = '00'BGeneric number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXITAccess transport parameter including the subaddress information


ETSI







number parameter codedAddress presentation restricted parameter = presentation allowedand with the Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not verifiedAddress signals included,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included.


CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXIT


ANM;Connected number parameterAddress presentation restricted parameter = '00'BGeneric number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXIT


ETSI







number parameter codedAddress presentation restricted parameter = presentation allowedand with the Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not verifiedAddress signals includedand with the connected subaddress in the Access transport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included


values:CONNECT;Connected number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXITConnected subaddress information element


ANM;Connected number parameterAddress presentation restricted parameter = '00'BGeneric number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXITAccess transport parameter including the subaddress information


Values for the test purposes TP503105 - TP503108VA_01 ISDN_TON = national number, '010'B ISUP_NAI = national number, '0000011'BVA_02 ISDN_TON = international number, '001'B ISUP_NAI = international number, '0000100'B

ETSI





criteria:COLR subscribed


Test purpose: Ensure that the SUT in state N3, on receipt of a CON message with a Connected numberparameter codedAddress presentation restricted parameter = presentation restricted,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.


CONNECT;Connected number information elementPresentation indicator = '01'BType of number = '000'BNumbering plan identification = '0000'BScreening indicator = '11'BNumber digits not included


CON;Connected number parameterAddress presentation restricted parameter = '01'B







Test purpose: Ensure that the SUT in state N3, on receipt of a CON message with a Connected numberparameter codedAddress presentation restricted parameter = presentation restrictedand with the connected subaddress in the Access transport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included

and without the Connected subaddress information element.ISDN Parameter

values:CONNECT;Connected number information elementPresentation indicator = '01'BType of number = '000'BNumbering plan identification = '0000'BScreening indicator = '11'BNumber digits not includedConnected subaddress information element not present


CON;Connected number parameterAddress presentation restricted parameter = '01'BAccess transport parameter including the subaddress information


ETSI







Test purpose: Ensure that the SUT in state N4, on receipt of an ANM message with a Connectednumber parameter codedAddress presentation restricted parameter = presentation restricted,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.




ANM;Connected number parameterAddress presentation restricted parameter = '01'B







Test purpose: Ensure that the SUT in state N4, on receipt of an ANM message with a Connectednumber parameter codedAddress presentation restricted parameter = presentation restrictedand with the connected subaddress in the Access transport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included




ANM;Connected number parameterAddress presentation restricted parameter = '01'BAccess transport parameter including the subaddress information


ETSI







parameter codedAddress presentation restricted parameter = address not available,

sends a CONNECT message with the Connected number information element codedPresentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.




CON;Connected number parameterAddress presentation restricted parameter = '10'B







parameter codedAddress presentation restricted parameter = address not availableand with the connected subaddress in the Access transport parameter,

sends a CONNECT message with the Connected number information element codedPresentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included




CON;Connected number parameterAddress presentation restricted parameter = '10'BAccess transport parameter including the subaddress information


ETSI







number parameter codedAddress presentation restricted parameter = address not available,

sends a CONNECT message with the Connected number information element codedPresentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.




ANM;Connected number parameterAddress presentation restricted parameter = '10'B







number parameter codedAddress presentation restricted parameter = address not availableand with the connected subaddress in the Access transport parameter,





ANM;Connected number parameterAddress presentation restricted parameter = '10'BAccess transport parameter including the subaddress information


ETSI






criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a CON message without a Connected

number parameter,sends a CONNECT message with the Connected number information element coded

Presentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.




CON;Connected number parameter not present






criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a CON message without a Connected

number parameter, but with the connected subaddress in the Access transportparameter,





CON;Connected number parameter not presentAccess transport parameter including the subaddress information


ETSI






criteria:Test purpose: Ensure that the SUT in state N4, on receipt of an ANM message without a Connected

number parameter,sends a CONNECT message with the Connected number information element coded





ANM;Connected number parameter not present






criteria:Test purpose: Ensure that the SUT in state N4, on receipt of an ANM message without a Connected

number parameter, but with the connected subaddress in the Access transportparameter,





ANM;Connected number parameter not presentAccess transport parameter including the subaddress information


ETSI


6.3.1.3.2 COLP not subscribed

ISDN selection criteria: COLP not subscribed.



TSS reference: DSS1-ISUP/SS/COLP/Subscribed/Not subscribedISDN selection



parameter and without the Generic number parameter,sends a CONNECT message without the Connected number information element.


CONNECT;Connected number information element not present


CON;Connected number parameter presentGeneric number parameter not present







parameter and with a Generic number parameter,sends a CONNECT message without the Connected number information element.




CON;Connected number parameter presentGeneric number parameter present







number parameter and without the Generic number parameter,sends a CONNECT message without the Connected number information element.




ANM;Connected number parameter presentGeneric number parameter not present


ETSI







number parameter and with a Generic number parameter,sends a CONNECT message without the Connected number information element.




ANM;Connected number parameter presentGeneric number parameter present


6.3.1.4 Subaddressing (SUB)



TSS reference: DSS1-ISUP/SS/SUBISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Called party

subaddress information element,sends an IAM message with the subaddress information in the Access transport

parameter.ISDN Parameter

values:SETUP;Called party subaddress information element


IAM;Access transport parameter including the subaddress information


ETSI


6.3.1.5 Call diversion (CDIV)

6.3.1.5.1 Reception of a "call is diverting" notification


ISUP reference:EN 300 899-1 [1], clause 2.1.2.8.1.2

TSS reference: DSS1-ISUP/SS/CDIV/NotificationISDN selection


criteria:Test purpose: Ensure that the SUT in state N2, on receipt of an ACM message indicating a first diversion

with the Backward call indicators parameter codedCalled party's status indicator = no indicationISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,

sends a CALL PROCEEDING message with the Notification indicator informationelement coded

Notification description = call is diverting.ISDN Parameter

values:CALL PROCEEDING;Notification indicator information elementNotification description = '1111011'B


ACM;Backward call indicators parameterCalled party's status indicator = '00'BISUP indicator = '1'BISDN indicator = '1'B,Call diversion information parameterNotification subscription option = ISUP_NSOGeneric notification indicator parameterNotification indicator = '1111011'B


ETSI







with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,

sends an ALERTING message with the Notification indicator information elementcoded


values:ALERTING;Notification indicator information elementNotification description = '1111011'B









with the Backward call indicators parameter codedCalled party's status indicator = no indicationISUP indicator = ISUP not used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,

sends a PROGRESS message with the Notification indicator information elementcoded


values:PROGRESS;Notification indicator information elementNotification description = '1111011'B




ETSI








sends a NOTIFY message with the Notification indicator information element codedNotification description = call is diverting.


NOTIFY;Notification indicator information elementNotification description = '1111011'B



Comments: ISUP ACM -> SUT -> NOTIFY ISDN





criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a CPG message indicating a first diversion

with the Event information parameter codedEvent indicator = ALERTING,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,





CPG;Event information parameterEvent indicator = '0000001'B,Call diversion information parameterNotification subscription option = ISUP_NSOGeneric notification indicator parameterNotification indicator = '1111011'B


ETSI







with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSO,the Generic notification indicator parameter codedNotification indicator = call is divertingand with a Progress indicator information element in the Access transport parameter,





CPG;Event information parameterEvent indicator = '0000010'B,Call diversion information parameterNotification subscription option = ISUP_NSOGeneric notification indicator parameterNotification indicator = '1111011'BAccess transport parameterProgress indicator information element included














ETSI







with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,






Comments: ISUP CPG -> SUT -> NOTIFY ISDN













Values for the test purposes TP505101 - TP505109VA_01 - ISUP_NSO = presentation allowed with

redirection number, '010'BVA_02 - ISUP_NSO = presentation allowed without

redirection number, '011'B

ETSI








sends a CALL PROCEEDING message without the Notification indicator informationelement.


CALL PROCEEDING;Notification indicator information element not present









with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,

sends an ALERTING message without the Notification indicator informationelement.


ALERTING;Notification indicator information element not present




ETSI







with the Backward call indicators parameter codedCalled party's status indicator = no indicationISUP indicator = ISUP not used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,

sends a PROGRESS message without the Notification indicator informationelement.


PROGRESS;Notification indicator information element not present












values:ACM;Backward call indicators parameterCalled party's status indicator = '00'BISUP indicator = '1'BISDN indicator = '1'B,Call diversion information parameterNotification subscription option = ISUP_NSOGeneric notification indicator parameterNotification indicator = '1111011'B

Comments: ISUP ACM -> SUT -> NOTIFY ISDN

ETSI







with the Event information parameter codedEvent indicator = ALERTING,the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,

sends an ALERTING message without the Notification indicator informationelement.


ALERTING;Notification indicator information element not present
















ETSI






















values:CPG;Event information parameterEvent indicator = '0000010'B,Call diversion information parameterNotification subscription option = ISUP_NSOGeneric notification indicator parameterNotification indicator = '1111011'B


ETSI












Values for the test purposes TP505110 - TP505118VA_01 - ISUP_NSO = Unknown, '000'BVA_02 - ISUP_NSO = presentation not allowed, '001'B





criteria:Test purpose: Ensure that the SUT in state N4, on receipt of a CPG message indicating a subsequent

diversion with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSO,the Generic notification indicator parameter codedNotification indicator = call is divertingand with a Progress indicator information element in the Access transport parameter,







ETSI







diversion with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is diverting,





Values for the test purposes TP505119 - TP505120VA_01 - ISUP_NSO = Unknown, '000'BVA_02 - ISUP_NSO = presentation not allowed, '001'B






diversion with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSORedirection reason = ISUP_RR,the Generic notification indicator parameter codedNotification indicator = call is divertingand with a Progress indicator information element in the Access transport parameter,





CPG;Event information parameterEvent indicator = '0000010'B,Call diversion information parameterNotification subscription option = ISUP_NSORedirection reason = ISUP_RRGeneric notification indicator parameterNotification indicator = '1111011'BAccess transport parameterProgress indicator information element included


ETSI







diversion with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSOand the Generic notification indicator parameter codedNotification indicator = call is divertingRedirection reason = ISUP_RR,





CPG;Event information parameterEvent indicator = '0000010'B,Call diversion information parameterNotification subscription option = ISUP_NSORedirection reason = ISUP_RRGeneric notification indicator parameterNotification indicator = '1111011'B



redirection number, '010'BISUP_RR = deflection during alerting, '0100'B

VA_02 - ISUP_NSO = presentation allowed withredirection number, '010'BISUP_RR = no reply, '0010'B

VA_03 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = deflection during alerting, '0100'B

VA_04 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = no reply, '0010'B

ETSI







diversion with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSORedirection reason = ISUP_RR,the Generic notification indicator parameter codedNotification indicator = call is divertingand with a Progress indicator information element in the Access transport parameter,





CPG;Event information parameterEvent indicator = '0000010'B,Call diversion information parameterNotification subscription option = ISUP_NSORedirection reason = ISUP_RRGeneric notification indicator parameterNotification indicator = '1111011'BAccess transport parameterProgress indicator information element included







diversion with the Event information parameter codedEvent indicator = PROGRESS,with the Call diversion information parameter codedNotification subscription option = ISUP_NSORedirection reason = ISUP_RRand the Generic notification indicator parameter codedNotification indicator = call is diverting,



values:CPG;Event information parameterEvent indicator = '0000010'B,Call diversion information parameterNotification subscription option = ISUP_NSORedirection reason = ISUP_RRGeneric notification indicator parameterNotification indicator = '1111011'B


ETSI



redirection number, '010'BISUP_RR = Unknown, '0000'B

VA_02 - ISUP_NSO = presentation allowed withredirection number, '010'BISUP_RR = User busy, '0001'B

VA_03 - ISUP_NSO = presentation allowed withredirection number, '010'BISUP_RR = unconditional, '0011'B

VA_04 - ISUP_NSO = presentation allowed withredirection number, '010'BISUP_RR = deflection immediate response,'0101'B

VA_05 - ISUP_NSO = presentation allowed withredirection number, '010'BISUP_RR = mobile subscriber not reachable,'0110'B

VA_06 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = Unknown, '0000'B

VA_07 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = User busy, '0001'B

VA_08 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = unconditional, '0011'B

VA_09 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = deflection immediate response,'0101'B

VA_10 - ISUP_NSO = presentation allowed withoutredirection number, '011'BISUP_RR = mobile subscriber not reachable,'0110'B

ETSI


6.3.1.5.2 Reception of the Redirection number restriction parameter



TSS reference: DSS1-ISUP/SS/CDIV/Redirection numberISDN selection


criteria:Test purpose: Ensure that the SUT in state N3, on receipt of an ACM message with the Backward call

indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,the Redirection number restriction parameter codedPresentation restricted indicator = Presentation allowedand the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,

sends an ALERTING message with the Redirection number information elementcoded

Type of number = ISDN_TON or unknownNumbering plan identification = ISDN/telephony numbering planPresentation indicator = presentation allowedNumber digits included.


ALERTING;Redirection number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BPresentation indicator = '00'BNumber digits = PIXIT


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'B,Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number restriction parameterPresentation restricted indicator = '00'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits = PIXIT


ETSI






criteria:Test purpose: Ensure that the SUT in state N3, having already received an ACM message with the Call

diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = ALERTING,and the Redirection number restriction parameter codedPresentation restricted indicator = Presentation allowed,




ALERTING;Redirection number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BPresentation indicator = '00'BNumber digits = PIXIT


ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits = PIXITCPG;Event information parameterEvent indicator = '0000001'B,Redirection number restriction parameterPresentation restricted indicator = '00'B


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = PROGRESS,the Redirection number restriction parameter codedPresentation restricted indicator = Presentation allowed,and with a Progress indicator information element in the Access transport parameter,

sends a PROGRESS message with the Redirection number information elementcoded



PROGRESS;Redirection number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BPresentation indicator = '00'BNumber digits = PIXIT


ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits = PIXITCPG;Event information parameterEvent indicator = '0000010'B,Redirection number restriction parameterPresentation restricted indicator = '00'BAccess transport parameter containing a Progress indicator information element


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = PROGRESSand Redirection number restriction parameter codedPresentation restricted indicator = Presentation allowed,

sends a NOTIFY message with the Redirection number information element codedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/telephony numbering planPresentation indicator = presentation allowedNumber digits included.


NOTIFY;Redirection number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BPresentation indicator = '00'BNumber digits = PIXIT




ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = ALERTINGand Redirection number restriction parameter codedPresentation restricted indicator = Presentation allowed,

sends a NOTIFY message with the Redirection number information element codedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/telephony numbering planPresentation indicator = presentation allowedNumber digits included.


NOTIFY;Redirection number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BPresentation indicator = '00'BNumber digits = PIXIT




ETSI






criteria:Test purpose: Ensure that the SUT in state N4, having already received a CPG message with the Call

diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a ANM message with the Redirection number restriction parameter codedPresentation restricted indicator = Presentation allowed,

sends a CONNECT message with the Redirection number information elementcoded



CONNECT;Redirection number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BPresentation indicator = '00'BNumber digits = PIXIT


CPG;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits = PIXITANM;Redirection number restriction parameterPresentation restricted indicator = '00'B


Values for the test purposes TP505201 - TP505206VA_01 ISUP_TON = national number, '010'B ISUP_NAI = national number, '0000011'BVA_02 ISUP_TON = international number, '001'B ISUP_NAI = international number, '0000100'B

ETSI







indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,the Redirection number restriction parameter codedPresentation restricted indicator = Presentation restrictedand the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,


Type of number = unknownNumbering plan identification = unknownPresentation indicator = presentation restrictedNumber digits not present.


ALERTING;Redirection number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BNumber digits not present


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'B,Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number restriction parameterPresentation restricted indicator = '01'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits present


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = ALERTINGand the Redirection number restriction parameter codedPresentation restricted indicator = Presentation restricted,






ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits presentCPG;Event information parameterEvent indicator = '0000001'B,Redirection number restriction parameterPresentation restricted indicator = '01'B


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = PROGRESS,the Redirection number restriction parameter codedPresentation restricted indicator = Presentation restricted,and with a Progress indicator information element in the Access transport parameter,




PROGRESS;Redirection number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BNumber digits not present


ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits presentCPG;Event information parameterEvent indicator = '0000010'B,Redirection number restriction parameterPresentation restricted indicator = '01'BAccess transport parameter containing a Progress indicator information element


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = PROGRESS,and the Redirection number restriction parameter codedPresentation restricted indicator = Presentation restricted,

sends a NOTIFY message with the Redirection number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = presentation restrictedNumber digits not present.


NOTIFY;Redirection number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BNumber digits not present




ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a CPG message with the Event information parameter codedEvent indicator = ALERTING,and the Redirection number restriction parameter codedPresentation restricted indicator = Presentation restricted,

sends a NOTIFY message with the Redirection number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = presentation restrictedNumber digits not present.






ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,and the Redirection number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN numbering planAddress digits present,on receipt of a ANM message with the Redirection number restriction parameter codedPresentation restricted indicator = Presentation restricted,




CONNECT;Redirection number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BNumber digits not present


ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress digits presentANM;Redirection number restriction parameterPresentation restricted indicator = '01'B


Values for the test purposes TP505207 - TP505212VA_01 - ISUP_NAI = national number, '0000011'BVA_02 - ISUP_NAI = international number, '0000100'B

ETSI







indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the Call diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is diverting,the Redirection number restriction parameterand without the Redirection number parameter,


Type of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingNumber digits not present.




ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'B,Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number restriction parameterRedirection number parameter not present


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is divertingand without the Redirection number parameter,on receipt of a CPG message with the Event information parameter codedEvent indicator = ALERTINGand the Redirection number restriction parameter,






ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameter not presentCPG;Event information parameterEvent indicator = '0000001'B,Redirection number restriction parameter


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is divertingand without the Redirection number parameter,on receipt of a CPG message with the Event information parameter codedEvent indicator = PROGRESS,the Redirection number restriction parameter,and with a Progress indicator information element in the Access transport parameter,




PROGRESS;Redirection number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '10'BNumber digits not present


ACM;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameter not presentCPG;Event information parameterEvent indicator = '0000010'B,Redirection number restriction parameterAccess transport parameter containing a Progress indicator information element


ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is divertingand without the Redirection number parameter,on receipt of a CPG message with the Event information parameter codedEvent indicator = PROGRESSand the Redirection number restriction parameter,

sends a NOTIFY message with the Redirection number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingNumber digits not present.






ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is divertingand without the Redirection number parameter,on receipt of a CPG message with the Event information parameter codedEvent indicator = ALERTINGand the Redirection number restriction parameter,

sends a NOTIFY message with the Redirection number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingNumber digits not present.






ETSI







diversion information parameter codedNotification subscription option = Presentation allowed with redirection number,the Generic notification indicator parameter codedNotification indicator = call is divertingand without the Redirection number parameter,on receipt of a ANM message with the Redirection number restriction parameter,




CONNECT;Redirection number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '10'BNumber digits not present


CPG;Call diversion information parameterNotification subscription option = '010'BGeneric notification indicator parameterNotification indicator = '1111011'BRedirection number parameter not presentANM;Redirection number restriction parameter


ETSI


6.3.1.6 Call Waiting (CW)



TSS reference: DSS1-ISUP/SS/CWISDN selection



indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand the Generic notification indicator parameter codedNotification indicator = call is a waiting call,


Notification description = call is a waiting call.ISDN Parameter



ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'B,Generic notification indicator parameterNotification indicator = '1100000'B






criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a CPG message with the Event information

parameter codedEvent indicator = ALERTINGand the Generic notification indicator parameter codedNotification indicator = call is a waiting call,





CPG;Event information parameterEvent indicator = '0000001'B,Generic notification indicator parameterNotification indicator = '1100000'B


ETSI







parameter codedEvent indicator = PROGRESS,the Generic notification indicator parameter codedNotification indicator = call is a waiting calland with a Progress indicator information element in the Access transport parameter,





CPG;Event information parameterEvent indicator = '0000010'B,Generic notification indicator parameterNotification indicator = '1100000'BAccess transport parameterProgress indicator information element included







parameter codedEvent indicator = PROGRESSand the Generic notification indicator parameter codedNotification indicator = call is a waiting call,

sends a NOTIFY message with the Notification indicator information element codedNotification description = call is a waiting call.




CPG;Event information parameterEvent indicator = '0000010'B,Generic notification indicator parameterNotification indicator = '1100000'B


ETSI


6.3.1.7 Call Hold (HOLD)

6.3.1.7.1 Notification received from the network



TSS reference: DSS1-ISUP/SS/HOLD/From networkISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a CPG message with the Generic

notification indicator parameter codedNotification indicator = Remote hold,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Remote hold.




CPG;Generic notification indicator parameterNotification indicator = '1111001'B




TSS reference: DSS1-ISUP/SS/HOLD/From networkISDN selection



notification indicator parameter codedNotification indicator = Remote retrieval,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Remote retrieval.






ETSI


6.3.1.7.2 Invocation at coincident S and T reference point

ISDN selection criteria: Call Hold subscribed, S/T reference point.



TSS reference: DSS1-ISUP/SS/HOLD/Invocation S TISDN selection

criteria:Call hold in N4 supported


Test purpose: Ensure that the SUT in state N4, on receipt of a HOLD message,sends a CPG message with the Generic notification indicator parameter coded

Notification indicator = Remote holdand the Event information parameter coded

Event indicator = Progress.ISDN Parameter

values:HOLD;


CPG;Generic notification indicator parameterNotification indicator = '1111001'BEvent information parameterEvent indicator = '0000010'B

Comments: ISDN HOLD -> SUT -> CPG ISUP





criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a HOLD message,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Remote hold

and the Event information parameter codedEvent indicator = Progress.


HOLD;




ETSI





criteria:Call hold in N4 supported


Test purpose: Ensure that the SUT in state N4, on receipt of a RETRIEVE message,sends a CPG message with the Generic notification indicator parameter coded

Notification indicator = Remote retrievaland the Event information parameter coded

Event indicator = Progress.ISDN Parameter

values:RETRIEVE;



Comments: ISDN RETRIEVE -> SUT -> CPG ISUP





criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a RETRIEVE message,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Remote retrieval



RETRIEVE;




ETSI


6.3.1.7.3 Notification received at T reference point

ISDN selection criteria: T reference point.



TSS reference: DSS1-ISUP/SS/HOLD/Notification TISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a NOTIFY message with the Notification

indicator information element codedNotification description = Remote hold,







Comments: ISDN NOTIFY -> SUT -> CPG ISUP



TSS reference: DSS1-ISUP/SS/HOLD/Notification TISDN selection



indicator information element codedNotification description = Remote retrieval,








ETSI


6.3.1.8 Terminal Portability (TP)




TSS reference: DSS1-ISUP/SS/TP/From networkISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a SUS message with the Suspend/resume

indicators parameter codedSuspend resume indicator = ISDN subscriber initiated,

sends a NOTIFY message with the Notification indicator information element codedNotification description = user suspended.




SUS;Suspend/resume indicators parameterSuspend resume indicator = '0'B

Comments: ISUP SUS -> SUT -> NOTIFY ISDN





criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a RES message with the Suspend/resume


sends a NOTIFY message with the Notification indicator information element codedNotification description = user resumed.




RES;Suspend/resume indicators parameterSuspend resume indicator = '0'B

Comments: ISUP RES -> SUT -> NOTIFY ISDN






notification indicator parameter codedNotification indicator = user suspended,







ETSI







notification indicator parameter codedNotification indicator = user resumed,








ISDN selection criteria: Terminal Portability subscribed, S/T reference point.



TSS reference: DSS1-ISUP/SS/TP/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a SUSPEND message,

sends a SUS message with the Suspend/resume indicators parameter codedSuspend resume indicator = ISDN subscriber initiated,.


SUSPEND;



Comments: ISDN SUSPEND -> SUT -> SUS ISUP



TSS reference: DSS1-ISUP/SS/TP/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N0, on receipt of a RESUME message,

sends a RES message with the Suspend/resume indicators parameter codedSuspend resume indicator = ISDN subscriber initiated,.


RESUME;



Comments: ISDN RESUME -> SUT -> RES ISUP

ETSI






TSS reference: DSS1-ISUP/SS/TP/Notification TISDN selection



indicator information element codedNotification description = user suspended,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = user suspended









TSS reference: DSS1-ISUP/SS/TP/Notification TISDN selection



indicator information element codedNotification description = user resumed,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = user resumed







ETSI


6.3.1.9 Conference Calling (CONF)




TSS reference: DSS1-ISUP/SS/CONF/From networkISDN selection



notification indicator parameter codedNotification indicator = Conference established,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Conference established.











notification indicator parameter codedNotification indicator = Conference disconnected,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Conference disconnected.











notification indicator parameter codedNotification indicator = Other party added,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party added.






ETSI







notification indicator parameter codedNotification indicator = Isolated,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Isolated.











notification indicator parameter codedNotification indicator = Reattached,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Reattached.











notification indicator parameter codedNotification indicator = Other party isolated,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party isolated.






ETSI







notification indicator parameter codedNotification indicator = Other party reattached,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party reattached.











notification indicator parameter codedNotification indicator = Other party split,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party split.











notification indicator parameter codedNotification indicator = Other party disconnected,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party disconnected.






ETSI







notification indicator parameter codedNotification indicator = Conference floating,



values:CPG;Generic notification indicator parameterNotification indicator = '1001011'B



ISDN selection criteria: Conference Calling subscribed, S/T reference point.

NOTE: User A; user B: remote users of the conference call.



TSS reference: DSS1-ISUP/SS/CONF/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a FACILITY message with the Facility

information element containing a BeginCONF invoke component,sends a CPG message with the Generic notification indicator parameter coded

Notification indicator = Conference established.ISDN Parameter

values:FACILITY;Facility information elementComponent = BeginCONF invoke component



Comments: ISDN FACILITY -> SUT -> CPG ISUP

ETSI






criteria:Test purpose: Ensure that the SUT with two calls in state N10 (towards remote users A and user B;

conference has been established with the call towards user A), on receipt of a FACILITYmessage for remote user B with the Facility information element containing a AddCONFinvoke component,

sends towards user B a CPG message with the Generic notification indicatorparameter coded

Notification indicator = Conference establishedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party added.


FACILITY;Facility information elementComponent = AddCONF invoke component


User B: CPG;Generic notification indicator parameterNotification indicator = '1000010'BUser A: CPG;Generic notification indicator parameterNotification indicator = '1000100'B

Comments: ISDN FACILITY -> SUT -> 2 CPG ISUP





criteria:Test purpose: Ensure that the SUT in state N10 (conference established, remote users A and user B), on

receipt of a FACILITY message with the Facility information element containing aAddCONF invoke componentPartyId = user B,


Notification indicator = Isolatedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party isolated.


FACILITY;Facility information elementComponent = IsolateCONF invoke componentPartyId = user B




ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (conference established, remote users A and user B, user

B isolated), on receipt of a FACILITY message with the Facility information elementcontaining a ReattachCONF invoke componentPartyId = user B,


Notification indicator = Reattachedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party reattached.











receipt of a FACILITY message with the Facility information element containing aSplitCONF invoke componentPartyId = user B,


Notification indicator = Conference disconnectedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party split.






ETSI







receipt of a FACILITY message with the Facility information element containing aDropCONF invoke componentPartyId = user B,

sends towards user B a REL messageand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party disconnected.




User B: REL;User A: CPG;Generic notification indicator parameterNotification indicator = '1001010'B

Comments: ISDN FACILITY -> SUT -> REL ISUP (B), CPG ISUP (A)






receipt of a DISCONNECT message,sends towards user B a REL messageand sends towards user A a REL message.


DISCONNECT;


User B: REL;User A: REL;

Comments: ISDN DISCONNECT -> SUT -> 2 REL ISUP






receipt of a REL message from user B,sends a FACILITY message with the Facility information element containing a

PartyDISC invoke componentPartyId = user B.


FACILITY;Facility information elementComponent = PartyDISC invoke componentPartyId = user B


User B: REL;

Comments: ISUP REL -> SUT -> FACILITY ISDN

ETSI


6.3.1.9.3 Notification at T reference point




TSS reference: DSS1-ISUP/SS/CONF/Notification TISDN selection



indicator information element codedNotification description = Conference established,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Conference established






Comments: ISDN NOTIFY -> SUT -> ISUP CPG






indicator information element codedNotification description = Conference disconnected,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Conference disconnected







ETSI







indicator information element codedNotification description = Other party added,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party added












indicator information element codedNotification description = Isolated,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Isolated







ETSI







indicator information element codedNotification description = Reattached,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Reattached












indicator information element codedNotification description = Other party isolated,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party isolated







ETSI







indicator information element codedNotification description = Other party reattached,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party reattached












indicator information element codedNotification description = Other party split,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party split







ETSI







indicator information element codedNotification description = Other party disconnected,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party disconnected







6.3.1.10 Three-party (3PTY)




TSS reference: DSS1-ISUP/SS/3PTY/From networkISDN selection










ETSI



















notification indicator parameter codedNotification indicator = remote hold,

sends a NOTIFY message with the Notification indicator information element codedNotification description = remote hold.






ETSI






criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a CPG message with one Generic

notification indicator parameter codedNotification indicator = Conference disconnectedand another Generic notification indicator parameter codedNotification indicator = remote hold,,

sends two Notification indicator information elements in either one or two NOTIFYmessages, one coded

Notification description = Conference disconnectedand the other coded

Notification description = remote hold.ISDN Parameter

values:One or two NOTIFYsNotification indicator information elementNotification description = '1000011'BNotification indicator information elementNotification description = '1111001'B


CPG;Generic notification indicator parameterNotification indicator = '1000011'BGeneric notification indicator parameterNotification indicator = '1111001'B

Comments: ISUP CPG -> SUT -> 1 or 2 NOTIFY ISDN


ISDN selection criteria: Three-party subscribed, S/T reference point.

NOTE 1: User A: served user; users B and C: remote users.

NOTE 2: Call A-B: Active-held connection; Call A-C: Active-idle connection.



TSS reference: DSS1-ISUP/SS/3PTY/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT with two calls in state N10 (towards remote users B and user C), on

receipt of a FACILITY message for call A-B with the Facility information elementcontaining a Begin3PTY invoke component,


Notification indicator = Conference establishedand sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = Conference established.


FACILITY;Facility information elementComponent = Begin3PTY invoke component


User B: CPG;Generic notification indicator parameterNotification indicator = '1000010'BUser C: CPG;Generic notification indicator parameterNotification indicator = '1000010'B


ETSI






criteria:Test purpose: Ensure that the SUT with two calls in state N10 (towards remote users B and user C; 3PTY

conference has been established), on receipt of a FACILITY message for call A-B with theFacility information element containing an End3PTY invoke component,


Notification indicator = remote holdand sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = Conference disconnected.


FACILITY;Facility information elementComponent = End3PTY invoke component









conference has been disconnected), on receipt of a HOLD message for call A-C,sends no message towards user Band sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = remote hold.


HOLD;


User B: -;User C: CPG;Generic notification indicator parameterNotification indicator = '1111001'B


ETSI







conference has been disconnected, call A-C has been put on hold), on receipt of aRETRIEVE message for call A-B,


Notification indicator = Conference disconnectedand sends no message towards user C.


RETRIEVE;


User B: CPG;Generic notification indicator parameterNotification indicator = '1000011'BUser C: -;







conference has been established), on receipt of a FACILITY message for call A-C with theFacility information element containing an End3PTY invoke component,

sends towards user B a CPG message with one Generic notification indicatorparameter coded

Notification indicator = Conference disconnected,the other Generic notification indicator parameter coded






User B: CPG;Generic notification indicator parameterNotification indicator = '1000011'BGeneric notification indicator parameterNotification indicator = '1111001'BUser C: CPG;Generic notification indicator parameterNotification indicator = '1000011'B


ETSI







conference has been established), on receipt of a DISCONNECT message for call A-B,sends towards user B a REL message and sends towards user C a CPG message with

the Generic notification indicator parameter codedNotification indicator = Conference disconnected.


DISCONNECT;


User B: REL;User C: CPG;Generic notification indicator parameterNotification indicator = '1000011'B

Comments: ISDN FACILITY -> SUT -> REL ISUP (B), CPG ISUP (C)






conference has been established), on receipt of a DISCONNECT message for call A-C,sends towards user B a CPG message with the Generic notification indicator

parameter codedNotification indicator = remote hold

and sends towards user C a REL message.ISDN Parameter

values:DISCONNECT;


User B: CPG;Generic notification indicator parameterNotification indicator = '1111001'BUser C: REL;

Comments: ISDN FACILITY -> SUT -> CPG ISUP (B), REL ISUP (C)





criteria:Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B, call towards user C

has been disconnected; 3PTY conference had been established), on receipt of aRETRIEVE message for call A-B,


Notification indicator = Conference disconnected.ISDN Parameter

values:RETRIEVE;




ETSI







conference has been established), on receipt of a REL message from user B,sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = Conference disconnected

and sends a DISCONNECT message for call A-B.ISDN Parameter

values:DISCONNECT;



Comments: ISUP REL (B) -> SUT -> DISCONNECT ISDN (A-B), CPG ISUP (C)






conference has been established), on receipt of a REL message from user C,sends towards user B a CPG message with the Generic notification indicator


and sends a DISCONNECT message for call A-C.ISDN Parameter

values:DISCONNECT;



Comments: ISUP REL (C) -> SUT -> DISCONNECT ISDN (A-C), CPG ISUP (B)





criteria:Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B, user C has

disconnected; 3PTY conference had been established), on receipt of a RETRIEVEmessage for call A-B,



values:RETRIEVE;


User B: REL;Generic notification indicator parameterNotification indicator = '1000011'BUser C: -;


ETSI






























ETSI







indicator information element codedNotification description = remote hold,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = remote hold







6.3.1.11 Closed User Group (CUG)

6.3.1.11.1 CUG subscribed

ISDN selection criteria: CUG subscribed.



TSS reference: DSS1-ISUP/SS/CUG/SubscribedISDN selection


criteria:Test purpose: Ensure that the SUT in state N3 (implicit CUG request), on receipt of a REL message with

the Cause indicators parameter codedCause value = 55, Incoming calls barred within CUG,

sends a DISCONNECT message with the Cause information element codedCause value = 29, Facility rejected.


DISCONNECT;Cause information elementCause value = '0011101'B


REL;Cause indicators parameterCause value = '0110111'B

Comments: ISUP REL -> SUT -> ISDN DISCONNECT

ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (explicit CUG request), on receipt of a REL message with

the Cause indicators parameter codedCause value = 55, Incoming calls barred within CUG,

sends a DISCONNECT message with the Cause information element codedCause value = 29, Facility rejected

and with the Facility information element containing a CUGCall return errorcomponent coded

Error value = incomingCallBarredWithinCUG.ISDN Parameter

values:DISCONNECT;Cause information elementCause value = '0011101'BFacility information elementComponent = CUGCall return errorError value = 19









the Cause indicators parameter codedCause value = 87, User not member of CUG,

sends a DISCONNECT message with the Cause information element codedCause value = 87, User not member of CUG.






ETSI







the Cause indicators parameter codedCause value = 87, User not member of CUG,



Error value = userNotMemberOfCUG.ISDN Parameter










the Cause indicators parameter codedCause value = 29, Facility rejectedDiagnostics = Closed user group interlock code parameter name,





REL;Cause indicators parameterCause value = '0011101'BDiagnostics = '00011010'B


ETSI







the Cause indicators parameter codedCause value = 29, Facility rejectedDiagnostics = Closed user group interlock code parameter name,



Error value = userNotMemberOfCUG.ISDN Parameter



REL;Cause indicators parameterCause value = '0011101'BDiagnostics = 00011010'B







the Cause indicators parameter codedCause value = other than 29, 55 or 87,

sends a DISCONNECT message.ISDN Parameter

values:DISCONNECT;


REL;Cause indicators parameterCause value = PIXIT


ETSI







the Cause indicators parameter codedCause value = other than 29, 55 or 87,

sends a DISCONNECT message with the Facility information element containing aCUGCall return error component coded

Error value = basicServiceNotProvided.ISDN Parameter

values:DISCONNECT;Facility information elementComponent = CUGCall return errorError value = 8


REL;Cause indicators parameterCause value = PIXIT


TP511109 ISDN reference:EN 300 138-1 [24], table 4

ISUP reference:ETS 300 356-9 [12], clause 1.5


criteria:CUG subscription option: Barring within the CUG <> outgoing call


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Facilityinformation element containing a CUGCall invoke component coded,OARequested = ISDN_OARCUGIndex present,

sends an IAM message with the Optional forward call indicators parameter codedClosed user group call indicator = closed user group call, outgoing access allowed

or closed user group call, outgoing access not allowedand with the Closed user group interlock code parameter giving the interlock code of

the CUG identified by the CUGIndex.ISDN Parameter

values:SETUP;Facility information elementComponent = CUGCall invoke componentOARequested = ISDN_OARCUGIndex = PIXIT


IAM;Optional forward call indicators parameterClosed user group call indicator = '10'B or '11'BClosed user group interlock code parameter = PIXIT


Values for the test purposes TP511109VA_01 ISDN_OAR = TRUE -VA_02 ISDN_OAR = FALSE -

Comments: The above test case has to be tested for the following combinations of subscription optionsavailable per ISDN number (see EN 300 138-2 [30]; table 1):1. Preferential CUG = Non designated Outgoing access = Not allowed.2. Preferential CUG = Non designated Outgoing access = Allowed.3. Preferential CUG = Nominated CUGIndex Outgoing access = Not allowed.4. Preferential CUG = Nominated CUGIndex Outgoing access = Allowed.

ETSI





criteria:CUG subscription option: Barring within the CUG <> outgoing call ANDISDN number subscription option: Preferential CUG = nominated CUGIndex


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Facilityinformation element containing a CUGCall invoke component coded,OARequested = FALSECUGIndex not present,



the nominated CUGIndex.ISDN Parameter

values:SETUP;Facility information elementComponent = CUGCall invoke componentOARequested = FALSECUGIndex not present







criteria:CUG subscription option: Barring within the CUG <> outgoing call ANDISDN number subscription option: Preferential CUG = nominated CUGIndex


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message without a Facilityinformation element,



the nominated CUGIndex.ISDN Parameter

values:SETUP;Facility information element not present




Values for the test purposes TP511110 and TP511111Comments: The above test cases have to be tested for the following subscription options available per ISDN

number (see EN 300 138-2 [30]; table 1):1. Outgoing access = Not allowed2. Outgoing access = Allowed

ETSI





criteria:ISDN number subscription option: Outgoing access = allowed


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Facilityinformation element containing a CUGCall invoke component coded,OARequested = TRUECUGIndex not present,

sends an IAM message optionally with the Optional forward call indicatorsparameter coded

Closed user group call indicator = non-CUG calland without the Closed user group interlock code parameter.


SETUP;Facility information elementComponent = CUGCall invoke componentOARequested = TRUECUGIndex not present


IAM;Optional forward call indicators parameter (presence optional)Closed user group call indicator = '00'BClosed user group interlock code parameter not present


Values for the test purposes TP511112Comments: The above test case has to be tested for the following combinations of subscription options

available per CUG and per ISDN number (see EN 300 138-2 [30]; tables 1 and 2):1. Barring within the CUG <> outgoing call Preferential CUG = Non designated2. Barring within the CUG = outgoing call Preferential CUG = Non designated3. Barring within the CUG <> outgoing call Preferential CUG = Nominated CUGIndex4. Barring within the CUG = outgoing call Preferential CUG = Nominated CUGIndex




criteria:ISDN number subscription option: Outgoing access = allowed ANDISDN number subscription option: Preferential CUG = non designated


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Facilityinformation element containing a CUGCall invoke component coded,OARequested = FALSECUGIndex not present,




SETUP;Facility information elementComponent = CUGCall invoke componentOARequested = FALSECUGIndex not present




ETSI





criteria:ISDN number subscription option: Outgoing access = allowed ANDISDN number subscription option: Preferential CUG = non designated


Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message without a Facilityinformation element,




SETUP;Facility information element not present




Values for the test purposes TP511113 and TP511114Comments: The above test cases have to be tested for the following subscription options available per CUG

(see EN 300 138-2 [30], table 2):1. Barring within the CUG <> outgoing call2. Barring within the CUG = outgoing call

6.3.1.11.2 CUG not subscribed



TSS reference: DSS1-ISUP/SS/CUG/Not subscribedISDN selection

criteria:CUG not subscribed


Test purpose: Ensure that the SUT in state N3, on receipt of a REL message with the Cause indicatorsparameter codedCause value = 87, User not member of CUG,







ETSI


6.3.1.12 User to User Signalling (UUS)

6.3.1.12.1 Service 1 (UUS1) implicit

ISDN selection criteria: UUS1 implicit subscribed.



TSS reference: DSS1-ISUP/SS/UUS/UUS1 implicitISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a User-user

information element without user information,sends an IAM message with the User-to-user parameter without user information.


SETUP;User-user information elementUser information not present


IAM;User-to-user parameterUser information not present






criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a User-user

information element with user information,sends an IAM message with the User-to-user parameter with user information.


SETUP;User-user information elementUser information present


IAM;User-to-user parameterUser information present


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been activated), on receipt of an ACM

message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand with a User-to-user parameter,

sends an ALERTING message with a User-user information element.ISDN Parameter

values:ALERTING;User-user information element


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been activated), on receipt of a CPG message

with the Event information parameter codedEvent indicator = ALERTINGand with a User-to-user parameter,

sends an ALERTING message with a User-user information element.ISDN Parameter

values:ALERTING;User-user information element


CPG;Event information parameterEvent indicator = '0000001'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been activated), on receipt of a CON message

with a User-to-user parameter,sends a CONNECT message with a User-user information element.


CONNECT;User-user information element


CON;User-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N4 (UUS1 has been activated), on receipt of an ANM

message with a User-to-user parameter,sends a CONNECT message with a User-user information element.




ANM;User-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N4 (UUS1 has been activated), on receipt of a REL message

with a User-to-user parameter,sends a DISCONNECT message with a User-user information element.


DISCONNECT;User-user information element


REL;User-to-user parameter

















criteria:Test purpose: Ensure that the SUT in state N4 (UUS1 has been activated), on receipt of a DISCONNECT

message with a User-user information element,sends a REL message with a User-to-user parameter.






ETSI






criteria:Test purpose: Ensure that the SUT in state N4 (UUS1 has been activated), on receipt of a RELEASE



RELEASE;User-user information element



Comments: ISDN RELEASE-> SUT -> REL ISUP






COMPLETE message with a User-user information element,sends a REL message with a User-to-user parameter.


RELEASE COMPLETE;User-user information element








criteria:Test purpose: Ensure that the SUT in state N10 (UUS1 has been activated), on receipt of a

DISCONNECT message with a User-user information element,sends a REL message with a User-to-user parameter.

















ETSI













6.3.1.12.2 Service 1 (UUS1) explicit

ISDN selection criteria: UUS1 explicit subscribed.



TSS reference: DSS1-ISUP/SS/UUS/UUS1 explicitISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a SETUP message with a Facility

information element containing a UserUserService invoke component codedService = Service1Preferred = preferred requestand without the User-user information element,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = request, not essentialService 2 = no informationService 3 = no information,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part preferred all the way

and without the User-to-user parameter.ISDN Parameter

values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = TrueUser-user information element not present


IAM;User-to-user indicators parameterType = '0'BService 1 = '10'BService 2 = '00'BService 3 = '00'BForward call indicators parameterISDN user part preference parameter = '00'BUser-to-user parameter not present


ETSI







information element containing a UserUserService invoke component codedService = Service1Preferred = preferred request,and with the User-user information element,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = request, not essentialService 2 = no informationService 3 = no information,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part preferred all the way

and with the User-to-user parameter.ISDN Parameter

values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = TrueUser-user information element


IAM;User-to-user indicators parameterType = '0'BService 1 = '10'BService 2 = '00'BService 3 = '00'BForward call indicators parameterISDN user part preference parameter = '00'BUser-to-user parameter


ETSI







information element containing a UserUserService invoke component codedService = Service1Preferred = required requestand without the User-user information element,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = request, essentialService 2 = no informationService 3 = no information,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part required all the way


values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = FalseUser-user information element not present


IAM;User-to-user indicators parameterType = '0'BService 1 = '11'BService 2 = '00'BService 3 = '00'BForward call indicators parameterISDN user part preference parameter = '10'BUser-to-user parameter not present


ETSI







information element containing a UserUserService invoke component codedService = Service1Preferred = required requestand with the User-user information element,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = request, essentialService 2 = no informationService 3 = no information,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part required all the way


values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = FalseUser-user information element


IAM;User-to-user indicators parameterType = '0'BService 1 = '11'BService 2 = '00'BService 3 = '00'BForward call indicators parameterISDN user part preference parameter = '10'BUser-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested), on receipt of an ACM

message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the User-to-user indicators parameter codedType = responseService 1 = providedand without a User-to-user parameter,

sends an ALERTING message with a Facility information element containing aUserUserService return result component and without the User-user informationelement.


ALERTING;Facility information elementUserUserService return result componentUser-user information element not present


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'BUser-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter not present







message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDN,the User-to-user indicators parameter codedType = responseService 1 = providedand with a User-to-user parameter,

sends an ALERTING message with a Facility information element containing aUserUserService return result component and with the User-user information element.


ALERTING;Facility information elementUserUserService return result componentUser-user information element


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'BUser-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested), on receipt of a CPG message

with the Event information parameter codedEvent indicator = ALERTINGthe User-to-user indicators parameter codedType = responseService 1 = providedand without a User-to-user parameter,

sends an ALERTING message with a Facility information element containing aUserUserService return result component and without the User-user informationelement.


ALERTING;Facility information elementUserUserService return result componentUser-user information element not present


CPG;Event information parameterEvent indicator = '0000001'BUser-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter not present







with the Event information parameter codedEvent indicator = ALERTINGthe User-to-user indicators parameter codedType = responseService 1 = providedand with a User-to-user parameter,

sends an ALERTING message with a Facility information element containing aUserUserService return result component and with the User-user information element.


ALERTING;Facility information elementUserUserService return result componentUser-user information element


CPG;Event information parameterEvent indicator = '0000001'BUser-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested), on receipt of an ANM

message with the User-to-user indicators parameter codedType = responseService 1 = providedand without a User-to-user parameter,

sends a CONNECT message with a Facility information element containing aUserUserService return result component and without the User-user informationelement.


CONNECT;Facility information elementUserUserService return result componentUser-user information element not present


ANM;User-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter not present







message with the User-to-user indicators parameter codedType = responseService 1 = providedand with a User-to-user parameter,

sends a CONNECT message with a Facility information element containing aUserUserService return result component and with the User-user information element.


CONNECT;Facility information elementUserUserService return result componentUser-user information element


ANM;User-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested), on receipt of a CON message

with the User-to-user indicators parameter codedType = responseService 1 = providedand without a User-to-user parameter,

sends a CONNECT message with a Facility information element containing aUserUserService return result component and without the User-user informationelement.


CONNECT;Facility information elementUserUserService return result componentUser-user information element not present


CON;User-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter not present







with the User-to-user indicators parameter codedType = responseService 1 = providedand with a User-to-user parameter,

sends a CONNECT message with a Facility information element containing aUserUserService return result component and with the User-user information element.


CONNECT;Facility information elementUserUserService return result componentUser-user information element


CON;User-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested), on receipt of a REL message

with the User-to-user indicators parameter codedType = responseService 1 = providedand without a User-to-user parameter,

sends a DISCONNECT message with a Facility information element containing aUserUserService return result component and without the User-user informationelement.


DISCONNECT;Facility information elementUserUserService return result componentUser-user information element not present


REL;User-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter not present






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested), on receipt of a REL message

with the User-to-user indicators parameter codedType = responseService 1 = providedand with a User-to-user parameter,

sends a DISCONNECT message with a Facility information element containing aUserUserService return result component and with the User-user information element.


DISCONNECT;Facility information elementUserUserService return result componentUser-user information element


REL;User-to-user indicators parameterType = '1'BService 1 = '10'BUser-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N4 (UUS1 has been activated), on receipt of an ANM

message with the User-to-user parameter,sends a CONNECT message with the User-user information element.











with the User-to-user parameter,sends a DISCONNECT message with the User-user information element.











with the User-to-user parameter,sends a DISCONNECT message with the User-user information element.

















ETSI














































ETSI

















criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested as “required"), on receipt of a

REL message with the Cause parameter codedCause value = ISUP_CVDiagnostics = User-user indicators parameter name,

sends a DISCONNECT message with the Cause information element codedCause value = ISDN_CV,

and with a Facility information element containing a UserUserService return errorcomponent coded

Error value = rejectedByUser.ISDN Parameter

values:DISCONNECT;Cause information elementCause value = ISDN_CVFacility information elementUserUserService return error componentError value = 2


REL;Cause parameterCause value = ISUP_CVDiagnostics = '00101010'B


Values for the test purposes TP512224VA_01 ISDN_CV = 29, Facility rejected, 0011101'B ISUP_CV = 29, Facility rejected, 0011101'BVA_02 ISDN_CV = 69, Requested facility not

implemented, 1000101'BISUP_CV = 69, Requested facility notimplemented, 1000101'B

ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested as “required"), on receipt of an

ANM message without the User-to-user indicators parameter,sends a DISCONNECT message with the Cause information element coded

Cause value = 69, Requested facility not implemented,and with a Facility information element containing a UserUserService return error

component codedError value = rejectedByUser.


DISCONNECT;Cause information elementCause value = 1000101'BFacility information elementUserUserService return error componentError value = 2


ANM;User-to-user indicators parameter not present

Comments: ISUP ANM -> SUT -> DISCONNECT ISDN






CON message without the User-to-user indicators parameter,sends a DISCONNECT message with the Cause information element coded






CON;User-to-user indicators parameter not present

Comments: ISUP CON -> SUT -> DISCONNECT ISDN

ETSI







REL message without the User-to-user indicators parameter,sends a DISCONNECT message with the Cause information element coded






REL;User-to-user indicators parameter not present






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested as “preferred"), on receipt of

an ACM message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand the User-to-user indicators parameter codedType = responseService 1 = not provided,

sends an ALERTING message with a Facility information element containing aUserUserService return error component coded


values:ALERTING;Facility information elementUserUserService return error componentError value = 2


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'BUser-to-user indicators parameterType = '1'BService 1 = '01'B


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (UUS1 has been requested as “preferred"), on receipt of a

CPG message with the Event information parameter codedEvent indicator = ALERTINGand the User-to-user indicators parameter codedType = responseService 1 = not provided,





CPG;Event information parameterEvent indicator = '0000001'BUser-to-user indicators parameterType = '1'BService 1 = '01'B







an ANM message with the User-to-user indicators parameter codedType = responseService 1 = not provided,

sends a CONNECT message with a Facility information element containing aUserUserService return error component coded


values:CONNECT;Facility information elementUserUserService return error componentError value = 2


ANM;User-to-user indicators parameterType = '1'BService 1 = '01'B


ETSI







CON message with the User-to-user indicators parameter codedType = responseService 1 = not provided,





CON;User-to-user indicators parameterType = '1'BService 1 = '01'B







REL message with the User-to-user indicators parameter codedType = responseService 1 = not provided,

sends a DISCONNECT message with a Facility information element containing aUserUserService return error component coded


values:DISCONNECT;Facility information elementUserUserService return error componentError value = 2


REL;User-to-user indicators parameterType = '1'BService 1 = '01'B


ETSI







an ANM message without the User-to-user indicators parameter,sends a CONNECT message with a Facility information element containing a

UserUserService return error component codedError value = rejectedByUser.


CONNECT;Facility information elementUserUserService return error componentError value = 2









CON message without the User-to-user indicators parameter,sends a CONNECT message with a Facility information element containing a












REL message without the User-to-user indicators parameter,sends a DISCONNECT message with a Facility information element containing a



DISCONNECT;Facility information elementUserUserService return error componentError value = 2




ETSI


6.3.1.12.3 Service 2 (UUS2)

ISDN selection criteria: UUS2 subscribed.



TSS reference: DSS1-ISUP/SS/UUS/UUS2ISDN selection



information element containing a UserUserService invoke component codedService = Service 2Preferred = preferred request,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = no informationService 2 = request, not essentialService 3 = no information,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part preferred all the way.


SETUP;Facility information elementUserUserService invoke componentService = 2Preferred = True


IAM;User-to-user indicators parameterType = '0'BService 1 = '00'BService 2 = '10'BService 3 = '00'BForward call indicators parameterISDN user part preference parameter = '00'B


ETSI







information element containing a UserUserService invoke component codedService = Service 2Preferred = required request,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = no informationService 2 = request, essentialService 3 = no information,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part required all the way.


SETUP;Facility information elementUserUserService invoke componentService = 2Preferred = False









message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand the User-to-user indicators parameter codedType = responseService 2 = provided,

sends an ALERTING message with a Facility information element containing aUserUserService return result component.


ALERTING;Facility information elementUserUserService return result component




ETSI







with the Event information parameter codedEvent indicator = ALERTINGand the User-to-user indicators parameter codedType = responseService 2 = provided,

sends an ALERTING message with a Facility information element containing aUserUserService return result component.










criteria:Test purpose: Ensure that the SUT in state N4 (UUS2 has been activated), on receipt of a USER

INFORMATION message with the User-user information element,sends a USR message with a User-to-user information parameter.


USER INFORMATION;User-user information elementMore data information element


USR;User-to-user information parameterMore data parameter

Comments: ISDN USER INFORMATION-> SUT -> USR ISUP






INFORMATION message with the User-user information element and the More datainformation element,

sends a USR message with a User-to-user information parameter and a More dataparameter.






ETSI






criteria:Test purpose: Ensure that the SUT in state N4 (UUS2 has been activated), on receipt of a USR message

with the User-to-user information parameter,sends a USER INFORMATION message with a User-user information element.


USER INFORMATION;User-user information element


USR;User-to-user information parameter

Comments: ISUP USR -> SUT -> USER INFORMATION ISDN






with the User-to-user information parameter and the More data parameter,sends a USER INFORMATION message with a User-user information element and a

More data information element.ISDN Parameter

values:USER INFORMATION;User-user information elementMore data information element

















ETSI




VA_03 ISDN_CV = 69, Requested facility notimplemented, 1000101'B

ISUP_CV = 88, Incompatible destination,1011000'B






message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand without the User-to-user indicators parameter,

sends a DISCONNECT message with the Cause information element codedCause value = 69, Requested facility not implemented,



values:DISCONNECT;Cause information elementCause value = 1000101'BFacility information elementUserUserService return error componentError value = 2


ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'BUser-to-user indicators parameter not present


ETSI







with the Event information parameter codedEvent indicator = ALERTINGand without the User-to-user indicators parameter,

sends a DISCONNECT message with the Cause information element codedCause value = 69, Requested facility not implemented,



values:DISCONNECT;Cause information elementCause value = 1000101'BFacility information elementUserUserService return error componentError value = 2


CPG;Event information parameterEvent indicator = '0000001'BUser-to-user indicators parameter not present







REL message without the User-to-user indicators parameter,sends a DISCONNECT message with the Cause information element coded








ETSI







an ACM message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand the User-to-user indicators parameter codedType = responseService 2 = not provided,












CPG message with the Event information parameter codedEvent indicator = ALERTINGand the User-to-user indicators parameter codedType = responseService 2 = not provided,







ETSI










values:DISCONNECT;Facility information elementUserUserService return error componentError value = 2









an ACM message with the Backward call indicators parameter codedCalled party's status indicator = subscriber freeISUP indicator = ISUP used all the wayISDN indicator = terminating access is ISDNand without the User-to-user indicators parameter,





ACM;Backward call indicators parameterCalled party's status indicator = '01'BISUP indicator = '1'BISDN indicator = '1'BUser-to-user indicators parameter not present


ETSI







CPG message with the Event information parameter codedEvent indicator = ALERTINGand without the User-to-user indicators parameter,





CPG;Event information parameterEvent indicator = '0000001'BUser-to-user indicators parameter not present







REL message without the User-to-user indicators parameter,sends a DISCONNECT message with a Facility information element containing a



DISCONNECT;Facility information elementUserUserService return error componentError value = 2




ETSI


6.3.1.12.4 Service 3 (UUS3)








sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = no informationService 2 = no informationService 3 = request, not essential,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part preferred all the way.






ETSI







information element containing a UserUserService invoke component codedService = Service 3Preferred = required request,

sends an IAM message with the User-to-user indicators parameter codedType = requestService 1 = no informationService 2 = no informationService 3 = request, essential,

the Forward call indicators parameter codedISDN user part preference parameter = ISDN user part required all the way.


SETUP;Facility information elementUserUserService invoke componentService = 3Preferred = False









with the User-to-user indicators parameter codedType = responseService 3 = provided,

sends a CONNECT message with a Facility information element containing aUserUserService return result component.


CONNECT;Facility information elementUserUserService return result component


CON;Type = '1'BService 3 = '10'B


ETSI







message with the User-to-user indicators parameter codedType = responseService 3 = provided,

sends a CONNECT message with a Facility information element containing aUserUserService return result component.




ANM;Type = '1'BService 3 = '10'B






criteria:Test purpose: Ensure that the SUT in the state N10, on receipt of a FACILITY message with a Facility


sends a FAR message with the User-to-user indicators parameter codedType = requestService 3 = request, not essential.


FACILITY;Facility information elementUserUserService invoke componentService = 3Preferred = True


FAR;User-to-user indicators parameterType = '0'BService 3 = '10'B

Comments: ISDN FACILITY -> SUT -> ISUP FAR

ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FAA

message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = provided,

sends a FACILITY message with a Facility information element containing aUserUserService return result component.


FACILITY;Facility information elementUserUserService return result component


FAA;User-to-user indicators parameterType = '1'BService 1 = '00'BService 2 = '00'BService 3 = '10'B

Comments: ISUP FAA -> SUT -> FACILITY ISDN





criteria:Test purpose: Ensure that the SUT in the state N10, on receipt of a FAR message with the User-to-user

indicators parameter codedType = requestService 3 = request, not essential,

sends a FACILITY message with a Facility information element containing aUserUserService invoke component coded

Service 1 = no informationService 2 = no informationService = Service 3Preferred = preferred request.




FAR;User-to-user indicators parameterType = '0'BService 1 = '00'BService 2 = '00'BService 3 = '10'B

Comments: ISUP FAR -> SUT -> ISDN FACILITY

ETSI






criteria:Test purpose: Ensure that the SUT in the state N10 (UUS3 has been requested), on receipt of a

FACILITY message with a Facility information element containing a UserUserServicereturn result component,

sends a FAA message with the User-to-user indicators parameter codedType = responseService 3 = provided.




FAA;User-to-user indicators parameterType = '1'BService 3 = '10'B

Comments: ISDN FACILITY -> SUT -> IAM FAA
























ETSI





































ETSI









ANM message without the User-to-user indicators parameter,sends a DISCONNECT message with the Cause information element coded


component codedError value = rejectedByNetwork.





Comments: ISUP ANM -> SUT -> DISCONNECT ISDN






CON message without the User-to-user indicators parameter,sends a DISCONNECT message with the Cause information element coded


component codedError value = rejectedByNetwork.





Comments: ISUP CON -> SUT -> DISCONNECT ISDN

ETSI







REL message without the User-to-user indicators parameter,sends a DISCONNECT message.


DISCONNECT;









an ANM message with the User-to-user indicators parameter codedType = responseService 3 = not provided,





ANM;User-to-user indicators parameterType = '1'BService 3 = '01'B







CON message with the User-to-user indicators parameter codedType = responseService 3 = not provided,





CON;User-to-user indicators parameterType = '1'BService 2 = '01'B


ETSI



















an ANM message without the User-to-user indicators parameter,sends a CONNECT message with a Facility information element containing a

UserUserService return error component codedError value = rejectedByNetwork.


ALERTING;Facility information elementUserUserService return error componentError value = 1


ACM;User-to-user indicators parameter not present







CON message without the User-to-user indicators parameter,sends a CONNECT message with a Facility information element containing a

UserUserService return error component codedError value = rejectedByNetwork.






ETSI







REL message without the User-to-user indicators parameter,sends a DISCONNECT message.


DISCONNECT;








criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FRJ

message with the User-to-user indicators parameter codedType = responseService 3 = not provided,

sends a FACILITY message with a Facility information element containing aUserUserService return error component coded


values:FACILITY;Facility information elementUserUserService return error componentError value = 2


FRJ;User-to-user indicators parameterType = '1'BService 3 = '01'B

Comments: ISUP FRJ -> SUT -> FACILITY ISDN

ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FACILITY

message with a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByUser,

sends a FRJ message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = not provided

and with a Cause parameter codedCause value = 29, Facility rejected.


FACILITY;Facility information elementUserUserService return error componentError value = 2


FRJ;User-to-user indicators parameterType = '1'BService 1 = '00'BService 2 = '00'BService 3 = '01'BCause parameterCause value = '0011101'B

Comments: ISDN FACILITY -> SUT -> ISUP FRJ




criteria:T reference point


Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FACILITYmessage with a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,








ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on the expiry of timer T1,


and with a Cause parameter codedCause value = 69, Requested facility not implemented.






6.3.1.13 Completion of Call to Busy Subscriber (CCBS)

ISDN selection criteria: CCBS subscribed.

6.3.1.13.1 S/T reference point

ISDN selection criteria: S/T reference point.



TSS reference: DSS1-ISUP/SS/CCBS/S T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a REL message with the Cause parameter

codedCause value = ISUP_CVDiagnostics = CCBS possible,

sends a DISCONNECT message with the Cause information element codedCause value = ISDN_CV

and with a Facility information element containing a CallInfoRetain invokecomponent.


DISCONNECT;Cause information elementCause value = ISDN_CVFacility information elementCallInfoRetain invoke component




ETSI


Values for the test purpose TP513101VA_01 ISDN_CV = 17, user busy, '0010001'B ISUP_CV = 17, user busy, '0010001'BVA_02 ISDN_CV = 34, no circuit/channel available,

'0100010'BISUP_CV = 34, no circuit/channel available,'0100010'B





criteria:Test purpose: Ensure that the SUT in the Idle state (CCBS has been activated, remote user free indication

has been delivered), on receipt of a SETUP message with a Facility information elementcontaining a CCBSCall invoke component,

sends an IAM message with the Forward call indicators parameter codedISDN user part preference indicator = ISDN user part required all the way

and the CCBS parameter codedCCBS call indicator = CCBS call.


SETUP;FACILITY information elementCCBSCall invoke component


IAM;Forward call indicators parameterISDN user part preference indicator = '10'BCCBS parameterCCBS call indicator = '1'B





criteria:CCBS request retention option supported


Test purpose: Ensure that the SUT in state N3 (CCBS call has been initiated), on receipt of a RELmessage with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCBS possible,


and without a Facility information element containing a CallInfoRetain invokecomponent.


DISCONNECT;Cause information elementCause value = ISDN_CVFacility information element not present




ETSI





criteria:CCBS request retention option not supported


Test purpose: Ensure that the SUT in state N3 (CCBS call has been initiated), on receipt of a RELmessage with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCBS possible,












criteria:Test purpose: Ensure that the SUT in state N3 (CCBS call has been initiated), on receipt of a REL

message with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCBS not possible,








Values for the test purpose TP513103 - TP513105VA_01 ISDN_CV = 17, user busy, '0010001'B ISUP_CV = 17, user busy, '0010001'BVA_02 ISDN_CV = 34, no circuit/channel available,


ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (CCBS call has been initiated), on receipt of a REL

message with the Cause parameter codedCause value = other than 17 or 34,

sends a DISCONNECT message and sends a FACILITY message with the dummy callreference and with a Facility information element containing a CCBSErase invokecomponent coded

eraseReason = basic-call-failed.ISDN Parameter

values:DISCONNECT;FACILITY;Dummy call referenceFacility information elementCCBSErase invoke componenteraseReason = 3


REL;Cause parameterCause value = other than 17 or 34

Comments: ISUP REL -> SUT -> ISDN DISCONNECT, FACILITY

6.3.1.13.2 T reference point




TSS reference: DSS1-ISUP/SS/CCBS/T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N3, on receipt of a REL message with the Cause parameter

codedCause value = ISUP_CVDiagnostics = CCBS possible,


and with a Facility information element containing a CCBS-T-Available invokecomponent.


DISCONNECT;Cause information elementCause value = ISDN_CVFacility information elementCCBS-T-Available invoke component




Values for the test purpose TP513201VA_01 ISDN_CV = 17, user busy, '0010001'B ISUP_CV = 17, user busy, '0010001'BVA_02 ISDN_CV = 34, no circuit/channel available,


ETSI




TSS reference: DSS1-ISUP/SS/CCBS/T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state (CCBS has been activated, remote user free indication

has been delivered), on receipt of a SETUP message with a Facility information elementcontaining a CCBS-T-Call invoke component,


and the CCBS parameter codedCCBS call indicator = CCBS call.


SETUP;FACILITY information elementCCBS-T-Call invoke component




6.3.1.14 Explicit Call Transfer (ECT)

ISDN selection criteria: ECT subscribed.



NOTE: User A: served user; users B and C: remote users.

ETSI


6.3.1.14.1.1 Loop prevention procedure

ISDN selection criteria: Loop prevention procedure supported.



TSS reference: DSS1-ISUP/SS/ECT/S T reference point/Loop preventionISDN selection


criteria:Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliary

state and towards user C in the Call Held auxiliary state), having received an implicitrequest for ECT for call A-C and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = no loop existsand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = no loop exists,

sends a FACILITY message for call A-C with the Facility information elementcontaining an EctExecute return result component.


FACILITY;Facility information elementComponent = EctExecute return result component


User B: LOP;Loop prevention indicators parameterType = '1'BResponse indicator = '01'BUser C: LOP;Loop prevention indicators parameterType = '1'BResponse indicator = '01'B

Comments: ISUP 2 LOP -> SUT -> FACILITY ISDN

ETSI







state and towards user C in the Call Held auxiliary state), having received an implicitrequest for ECT for call A-C and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = no loop existsand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = ISUP_RI,





User B: LOP;Loop prevention indicators parameterType = '1'BResponse indicator = '01'BUser C: LOP;Loop prevention indicators parameterType = '1'BResponse indicator = ISUP_RI







state and towards user C in the Call Held auxiliary state), having received an implicitrequest for ECT for call A-C and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = ISUP_RIand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = no loop exists,





User B: LOP;Loop prevention indicators parameterType = '1'BResponse indicator = ISUP_RIUser C: LOP;Loop prevention indicators parameterType = '1'BResponse indicator = '01'B


ETSI


Values for the test purpose TP514102 - TP514103VA_01 - ISUP_RI = insufficient information, '00'BVA_02 - ISUP_RI = simultaneous transfer, '10'B




criteria:Explicit linkage procedure supported


Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), having received an explicitrequest for ECT for call A-B and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = no loop existsand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = no loop exists,

sends a FACILITY message for call A-B with the Facility information elementcontaining an ExplicitEctExecute return result component.


FACILITY;Facility information elementComponent = ExplicitEctExecute return result component




ETSI







Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), having received an explicitrequest for ECT for call A-B and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = no loop existsand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = ISUP_RI,












Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Idle auxiliary state), having received an explicit request forECT for call A-B and having requested the procedure to avoid looping of uncontrolledcircuits, on receipt of a LOP message from user B with the Loop prevention indicatorsparameter codedType = responseResponse indicator = no loop existsand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = no loop exists,







ETSI







Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Idle auxiliary state), having received an explicit request forECT for call A-B and having requested the procedure to avoid looping of uncontrolledcircuits, on receipt of a LOP message from user B with the Loop prevention indicatorsparameter codedType = responseResponse indicator = no loop existsand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = ISUP_RI,







Values for the test purpose TP514104 - TP514107VA_01 - ISUP_RI = insufficient information, '00'BVA_02 - ISUP_RI = simultaneous transfer, '10'B

ETSI







Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), having received an explicitrequest for ECT for call A-B and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = ISUP_RIand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = no loop exists,












Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Idle auxiliary state), having received an explicit request forECT for call A-B and having requested the procedure to avoid looping of uncontrolledcircuits, on receipt of a LOP message from user B with the Loop prevention indicatorsparameter codedType = responseResponse indicator = ISUP_RIand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = no loop exists,







ETSI







state and towards user C in the Call Held auxiliary state), having received an implicitrequest for ECT for call A-C and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = simultaneous transferand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = simultaneous transfer,

sends a FACILITY message for call A-C with the Facility information elementcontaining an EctExecute return error component coded

Error value = notAvailable.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctExecute return error componentError value = 3








criteria:Call transfer rejection on “insufficient information" supported

Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), having received an implicitrequest for ECT for call A-C and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = insufficient informationand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = insufficient information,

sends a FACILITY message for call A-C with the Facility information elementcontaining an EctExecute return error component coded


values:FACILITY;Facility information elementComponent = EctExecute return error componentError value = 3




ETSI







Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), having received an explicitrequest for ECT for call A-B and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = simultaneous transferand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = simultaneous transfer,

sends a FACILITY message for call A-B with the Facility information elementcontaining an ExplicitEctExecute return error component coded


values:FACILITY;Facility information elementComponent = ExplicitEctExecute return error componentError value = 3




ETSI







Call transfer rejection on “insufficient information" supported

Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), having received an explicitrequest for ECT for call A-B and having requested the procedure to avoid looping ofuncontrolled circuits, on receipt of a LOP message from user B with the Loop preventionindicators parameter codedType = responseResponse indicator = insufficient informationand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = insufficient information,












Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Idle auxiliary state), having received an explicit request forECT for call A-B and having requested the procedure to avoid looping of uncontrolledcircuits, on receipt of a LOP message from user B with the Loop prevention indicatorsparameter codedType = responseResponse indicator = simultaneous transferand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = simultaneous transfer,







ETSI







Call transfer rejection on “insufficient information" supported

Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Idle auxiliary state), having received an explicit request forECT for call A-B and having requested the procedure to avoid looping of uncontrolledcircuits, on receipt of a LOP message from user B with the Loop prevention indicatorsparameter codedType = responseResponse indicator = insufficient informationand a LOP message from user C with the Loop prevention indicators parameter codedType = responseResponse indicator = insufficient information,







ETSI


6.3.1.14.1.2 Service invocation



TSS reference: DSS1-ISUP/SS/ECT/S T reference point/Service invocationISDN selection



state and towards user C in the Call Held auxiliary state), on receipt of a FACILITYmessage for call A-C with the Facility information element containing an EctExecuteinvoke component,

sends a FAC message towards user B with the Service activation parameter codedFeature code = call transfer

and the Generic notification parameter codedNotification indicator = Call transfer, active

and sends a FAC message towards user C with the Service activation parametercoded

Feature code = call transferand the Generic notification parameter coded

Notification indicator = Call transfer, active.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctExecute invoke component


User B: FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BUser C: FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'B

Comments: ISDN FACILITY -> SUT -> 2 FAC ISUP

ETSI







Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Call Held auxiliary state), on receipt of a FACILITYmessage for call A-B with the Facility information element containing anExplicitEctExecute invoke component,






values:FACILITY;Facility information elementComponent = ExplicitEctExecute invoke component




ETSI







Test purpose: Ensure that the SUT with two calls in state N10 (towards remote user B in the Idle auxiliarystate and towards user C in the Idle auxiliary state), on receipt of a FACILITY message forcall A-B with the Facility information element containing an ExplicitEctExecute invokecomponent,













criteria:ECT invocation in N4 supported


Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B in the Idle auxiliarystate) and one call in state N4 (towards user C in the Call Held auxiliary state), on receipt ofa FACILITY message for call A-C with the Facility information element containing anEctExecute invoke component,



and sends a CPG message towards user C with the Generic notification parametercoded

Notification indicator = Call transfer, alerting.ISDN Parameter



User B: FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101001'BUser C: CPG;Generic notification parameterNotification indicator = '1101010'B

Comments: ISDN FACILITY -> SUT -> FAC ISUP (B), CPG ISUP (C)

ETSI





criteria:ECT invocation in N4 supported


Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B in the Call Heldauxiliary state) and one call in state N4 (towards user C in the Idle auxiliary state), onreceipt of a FACILITY message for call A-B with the Facility information elementcontaining an EctExecute invoke component,


and the Generic notification parameter codedNotification indicator = Call transfer, alerting










criteria:ECT invocation in N4 supported AND Explicit linkage procedure supported


Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B in the Idle auxiliarystate) and one call in state N4 (towards user C in the Idle auxiliary state), on receipt of aFACILITY message for call A-C with the Facility information element containing anExplicitEctExecute invoke component,









ETSI







Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B in the Idle auxiliarystate) and one call in state N4 (towards user C in the Idle auxiliary state), on receipt of aFACILITY message for call A-B with the Facility information element containing anExplicitEctExecute invoke component,














Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B in the Call Heldauxiliary state) and one call in state N4 (towards user C in the Idle auxiliary state), onreceipt of a FACILITY message for call A-C with the Facility information elementcontaining an ExplicitEctExecute invoke component,









ETSI







Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B in the Idle auxiliarystate) and one call in state N4 (towards user C in the Call Held auxiliary state), on receipt ofa FACILITY message for call A-B with the Facility information element containing anExplicitEctExecute invoke component,















TSS reference: DSS1-ISUP/SS/ECT/T reference point/Loop preventionISDN selection



information element containing an EctLoopTest invoke component,sends a LOP message with the Loop prevention indicators parameter coded

Type = requestand with the Call transfer reference parameter.


FACILITY;Facility information elementComponent = EctLoopTest invoke component


LOP;Loop prevention indicators parameterType = '0'BCall transfer reference parameter

Comments: ISDN FACILITY -> SUT -> LOP ISUP

ETSI




TSS reference: DSS1-ISUP/SS/ECT/T reference point/Loop preventionISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, the procedure to avoid looping of uncontrolled circuits

has been requested, on receipt of a LOP message with the Loop prevention indicatorsparameter codedType = responseResponse indicator = ISUP_RIand with the Call transfer reference parameter,

sends a FACILITY message with the Facility information element containing anEctLoopTest return result component coded

LoopResult = ISDN_LR.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctLoopTest return result componentLoopResult = ISDN_LR


LOP;Loop prevention indicators parameterType = '1'BResponse indicator = ISUP_RICall transfer reference parameter

Comments: ISUP LOP -> SUT -> FACILITY ISDN

Values for the test purpose TP514302VA_01 ISUP_LR = insufficient information, 0 ISUP_RI = insufficient information, '00'BVA_02 ISUP_LR = no loop exists, 1 ISUP_RI = no loop exists, '01'BVA_03 ISUP_LR = simultaneous transfer, 2 ISUP_RI = simultaneous transfer, '10'B




TSS reference: DSS1-ISUP/SS/ECT/T reference point/Service invocationISDN selection



information element containing an EctInform invoke component codedArgument value = alerting,

sends a CPG message with the Event information parameter codedEvent type = Progress

and with the Generic notification parameter codedNotification indicator = Call transfer, alerting.


FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 0


CGP;Event information parameterType = '0000010'BGeneric notification parameterNotification indicator = '1101001'B

Comments: ISDN FACILITY -> SUT -> CGP ISUP

ETSI







information element containing an EctInform invoke component codedArgument value = alerting,

sends a FAC message with the Service activation parameter codedFeature code = Call transfer

and with the Generic notification parameter codedNotification indicator = Call transfer, alerting.


FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 0


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101001'B

Comments: ISDN FACILITY -> SUT -> FAC ISUP






information element containing an EctInform invoke component coded,Argument value = activeRedirection number presentand with a Facility information element containing a SubaddressTransfer invokecomponent,

sends a CPG message with the Event information parameter codedEvent type = Progress,

with the Generic notification parameter codedNotification indicator = Call transfer, active,

with the Call transfer number parameter and including the Facility information elementwith the SubaddressTransfer invoke component in the Access transport parameter.


FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 1Redirection number presentFacility information elementSubaddressTransfer invoke component


CGP;Event information parameterType = '0000010'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAccess transport parameter including the Facility information element with theSubaddressTransfer invoke component

Comments: ISDN FACILITY -> SUT -> CGP ISUP

ETSI







information element containing an EctInform invoke component codedArgument value = activeRedirection number presentand with a Facility information element containing a SubaddressTransfer invokecomponent,

sends a FAC message with the Service activation parameter codedFeature code = Call transfer,

with the Generic notification parameter codedNotification indicator = Call transfer, active,

with the Call transfer number parameter and including the Facility information elementwith the SubaddressTransfer invoke component in the Access transport parameter.


FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 1Redirection number presentFacility information elementSubaddressTransfer invoke component


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAccess transport parameter including the Facility information element with theSubaddressTransfer invoke component






criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a FAC message with the Service

activation parameter codedFeature code = Call transferand including a Facility information element with a SubaddressTransfer invoke componentin the Access transport parameter,

sends a FACILITY message with the Facility information element containing aSubaddressTransfer invoke component.


FACILITY;Facility information elementSubaddressTransfer invoke component


FAC;Service activation parameterFeature code = '00000001'BAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component

Comments: ISUP FAC -> SUT -> FACILITY ISDN

ETSI







information element containing a SubaddressTransfer invoke component,sends a FAC message with the Service activation parameter coded

Feature code = Call transferand including the Facility information element with the SubaddressTransfer invokecomponent in the Access transport parameter.


FACILITY;Facility information elementSubaddressTransfer invoke component


FAC;Service activation parameterFeature code = '00000001'BAccess transport parameter including the Facility information element with theSubaddressTransfer invoke component


6.3.1.15 Completion of Calls on No Reply (CCNR)

ISDN selection criteria: CCNR subscribed.




ISUP reference:EN 300 356-20 [29]

TSS reference: DSS1-ISUP/SS/CCNR/S T reference pointISDN selection



indicators parameter codedCalled party's status indicator = subscriber freeand with the CCNR possible indicator parameter codedCCNR possible indicator = CCNR possible,

sends an ALERTING message with the Facility information element containing aCallInfoRetain invoke component.


ALERTING;Facility information elementCallInfoRetain invoke component


ACM;Backward call indicators parameterCalled party's status indicator = '01'BCCNR possible indicator parameterCCNR possible indicator = '1'B

Comments: ISUP ACM -> SUT -> ISDN ALERTING

ETSI







parameter codedEvent indicator = ALERTINGand with the CCNR possible indicator parameter codedCCNR possible indicator = CCNR possible,

sends an ALERTING message with the Facility information element containing aCallInfoRetain invoke component.


ALERTING;Facility information elementCallInfoRetain invoke component


CPG;Event information parameterEvent indicator = '0000001'B,CCNR possible indicator parameterCCNR possible indicator = '1'B

Comments: ISUP CPG -> SUT -> ISDN ALERTING





criteria:Test purpose: Ensure that the SUT in the Idle state (CCNR has been activated, remote user free

indication has been delivered), on receipt of a SETUP message with a Facility informationelement containing a CCBSCall invoke component,


and the CCSS parameter codedCCSS call indicator = CCSS call.


SETUP;FACILITY information elementCCBSCall invoke component


IAM;Forward call indicators parameterISDN user part preference indicator = '10'BCCSS parameterCCSS call indicator = '1'B


ETSI





criteria:CCBS request retention option supported


Test purpose: Ensure that the SUT in state N3 (CCNR call has been initiated), on receipt of a RELmessage with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCNR possible,











criteria:CCBS request retention option not supported


Test purpose: Ensure that the SUT in state N3 (CCNR call has been initiated), on receipt of a RELmessage with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCNR possible,








ETSI






criteria:Test purpose: Ensure that the SUT in state N3 (CCNR call has been initiated), on receipt of a REL

message with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCBS not possible,














criteria:Test purpose: Ensure that the SUT in state N3 (CCNR call has been initiated), on receipt of a REL

message with the Cause parameter codedCause value = other than 17 or 34,

sends a DISCONNECT message and sends a FACILITY message with the dummy callreference and with a Facility information element containing a CCBSErase invokecomponent coded

eraseReason = basic-call-failed.ISDN Parameter

values:DISCONNECT;FACILITY;Dummy call referenceFacility information elementCCBSErase invoke componenteraseReason = 3


REL;Cause parameterCause value = other than 17 or 34

Comments: ISUP REL -> SUT -> ISDN DISCONNECT, FACILITY

ETSI






TSS reference: DSS1-ISUP/SS/CCNR/T reference pointISDN selection



indicators parameter codedCalled party's status indicator = subscriber freeand with the CCNR possible indicator parameter codedCCNR possible indicator = CCNR possible,

sends an ALERTING message with the Facility information element containing aCCBS-T-Available invoke component.


ALERTING;Facility information elementCCBS-T-Available invoke component



Comments: ISUP ACM -> SUT -> ISDN ALERTING






parameter codedEvent indicator = ALERTINGand with the CCNR possible indicator parameter codedCCNR possible indicator = CCNR possible,

sends an ALERTING message with the Facility information element containing aCCBS-T-Available invoke component.





Comments: ISUP CPG -> SUT -> ISDN ALERTING

ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state (CCNR has been activated, remote user free

indication has been delivered), on receipt of a SETUP message with a Facility informationelement containing a CCBS-T-Call invoke component,


and the CCSS parameter codedCCSS call indicator = CCSS call.






ETSI


6.3.2 Interworking from ISUP to DSS1 (Incoming Call)

6.3.2.1 Calling Line Identification Presentation (CLIP)

6.3.2.1.1 CLIP subscribed

ISDN selection criteria: CLIP subscribed.



TSS reference: ISUP-DSS1/SS/CLIP/SubscribedISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message with a Calling party

number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = ISUP_SIAddress signals includedand without the Generic number parameter,

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = ISDN_SINumber digits included.


SETUP;Calling party number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = ISDN_SINumber digits = PIXIT


IAM;Calling party number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = ISUP_SIAddress signals = PIXITGeneric number parameter not present

Comments: IAM ISUP -> SUT -> ISDN SETUP

ETSI







number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = ISUP_SIAddress signals included,without the Generic number parameter and with the calling party subaddress in theAccess transport parameter,

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = ISDN_SINumber digits included

and with the Calling party subaddress information element.ISDN Parameter

values:SETUP;Calling party number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = ISDN_SINumber digits = PIXITCalling party subaddress information element


IAM;Calling party number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = ISUP_SIAddress signals = PIXITGeneric number parameter not presentAccess transport parameter including subaddress information


Values for the test purposes TP601001 - TP601002VA_01 ISDN_TON = national number, '010'B

ISDN_SI = user provided verified and passed, '01'BISUP_NAI = national number, '0000011'BISUP_SI = user provided verified and passed, '01'B

VA_02 ISDN_TON = national number, '010'BISDN_SI = network provided, '11'B

ISUP_NAI = national number, '0000011'BISUP_SI = network provided, '11'B

VA_03 ISDN_TON = international number, '001'BISDN_SI = user provided verified and passed, '01'B

ISUP_NAI = international number, '0000100'BISUP_SI = user provided verified and passed, '01'B

VA_04 ISDN_TON = international number, '001'BISDN_SI = network provided, '11'B

ISUP_NAI = international number, '0000100'BISUP_SI = network provided, '11'B

ETSI





criteria:Two calling party delivery option does not apply


Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message with a Calling partynumber parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planScreening indicator = network providedAddress signals includedand with a Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not screenedAddress signals included,

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included.


SETUP;Calling party number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXIT2


IAM;Calling party number parameterAddress presentation restricted parameter = '00'BNature of address indicator = '0000011'BNumbering plan indicator = '001'BScreening indicator = '11'BAddress signals = PIXIT1Generic number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXIT2


ETSI





criteria:Two calling party delivery option does not apply


Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message with a Calling partynumber parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planScreening indicator = network providedAddress signals includedand with a Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not screenedAddress signals includedand with the calling party subaddress in the Access transport parameter,

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included


values:SETUP;Calling party number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXIT2Calling party subaddress information element


IAM;Calling party number parameterAddress presentation restricted parameter = '00'BNature of address indicator = '0000011'BNumbering plan indicator = '001'BScreening indicator = '11'BAddress signals = PIXIT1Generic number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXIT2Access transport parameter including subaddress information


ETSI





criteria:Two calling party delivery option applies


Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message with a Calling partynumber parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planScreening indicator = network providedAddress signals includedand with a Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not screenedAddress signals included,

sends a SETUP message with the first Calling party number information elementcoded

Presentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included

and the second Calling party number information element codedPresentation indicator = presentation allowedType of number = national number or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = network providedNumber digits included.


SETUP;First Calling party number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXIT1Second Calling party number information elementPresentation indicator = '00'BType of number = '010'B or '000'BNumbering plan identification = '0001'BScreening indicator = '11'BNumber digits = PIXIT2


IAM;Calling party number parameterAddress presentation restricted parameter = '00'BNature of address indicator = '0000011'BNumbering plan indicator = '001'BScreening indicator = '11'BAddress signals = PIXIT2Generic number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXIT1


ETSI





criteria:Two calling party delivery option applies


Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message with a Calling partynumber parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planScreening indicator = network providedAddress signals includedand with a Generic number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planScreening indicator = user provided, not screenedAddress signals includedand with the calling party subaddress in the Access transport parameter,

sends a SETUP message with the first Calling party number information elementcoded

Presentation indicator = presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = user provided, not screenedNumber digits included,

the second Calling party number information element codedPresentation indicator = presentation allowedType of number = national number or unknownNumbering plan identification = ISDN/Telephony numbering planScreening indicator = network providedNumber digits included


values:SETUP;First Calling party number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BScreening indicator = '00'BNumber digits = PIXIT1Second Calling party number information elementPresentation indicator = '00'BType of number = '010'B or '000'BNumbering plan identification = '0001'BScreening indicator = '11'BNumber digits = PIXIT2Calling party subaddress information element


IAM;Calling party number parameterAddress presentation restricted parameter = '00'BNature of address indicator = '0000011'BNumbering plan indicator = '001'BScreening indicator = '11'BAddress signals = PIXIT2Generic number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BScreening indicator = '00'BAddress signals = PIXIT1Access transport parameter including subaddress information


ETSI


Values for the test purposes TP601003 - TP601006VA_01 ISDN_TON = national number, '010'B ISUP_NAI = national number, '0000011'BVA_02 ISDN_TON = international number ISUP_NAI = international number, '0000100'B






number parameter codedAddress presentation restricted parameter = presentation restrictedand without a Generic number parameter,

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.


SETUP;Calling party number information elementPresentation indicator = '01'BType of number = '000'BNumbering plan identification = '0000'BScreening indicator = '11'BNumber digits not included


IAM;Calling party number parameterAddress presentation restricted parameter = '01'BGeneric number parameter not present


ETSI







number parameter codedAddress presentation restricted parameter = presentation restricted,without a Generic number parameter and with the calling party subaddress in the Accesstransport parameter

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included

and without the Calling party subaddress information element.ISDN Parameter

values:SETUP;Calling party number information elementPresentation indicator = '01'BType of number = '000'BNumbering plan identification = '0000'BScreening indicator = '11'BNumber digits not includedCalling party subaddress information element not present


IAM;Calling party number parameterAddress presentation restricted parameter = '01'BGeneric number parameter not presentAccess transport parameter including subaddress information







number parameter codedAddress presentation restricted parameter = presentation restrictedand with a Generic number parameter,

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.




IAM;Calling party number parameterAddress presentation restricted parameter = '01'BGeneric number parameter


ETSI







number parameter codedAddress presentation restricted parameter = presentation restricted,with a Generic number parameter and with the calling party subaddress in the Accesstransport parameter

sends a SETUP message with the Calling party number information element codedPresentation indicator = presentation restrictedType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included




IAM;Calling party number parameterAddress presentation restricted parameter = '01'BGeneric number parameterAccess transport parameter including subaddress information







number parameter codedAddress presentation restricted parameter = address not available,

sends a SETUP message with the Calling party number information element codedPresentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included.




IAM;Calling party number parameterAddress presentation restricted parameter = '10'B


ETSI







number parameter codedAddress presentation restricted parameter = address not availableand with the calling party subaddress in the Access transport parameter

sends a SETUP message with the Calling party number information element codedPresentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included




IAM;Calling party number parameterAddress presentation restricted parameter = '10'BAccess transport parameter including subaddress information






criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message without the Calling

party number parameter,sends a SETUP message with the Calling party number information element coded



SETUP;Calling party number information elementPresentation indicator = '10'B


IAM;Calling party number parameter not present


ETSI






criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message without the Calling

party number parameter but with the calling party subaddress in the Access transportparameter

sends a SETUP message with the Calling party number information element codedPresentation indicator = number not available due to interworkingType of number = unknownNumbering plan identification = unknownScreening indicator = network providedNumber digits not included




IAM;Calling party number parameter not presentAccess transport parameter including subaddress information


6.3.2.1.2 CLIP not subscribed

ISDN selection criteria: CLIP not subscribed.



TSS reference: ISUP-DSS1/SS/CLIP/Not subscribedISDN selection



number parameter and without the Generic number parameter,sends a SETUP message without the Calling party number information element.


SETUP;Calling party number information element not present


IAM;Calling party number parameterGeneric number parameter not present


ETSI




TSS reference: ISUP-DSS1/SS/CLIP/Not subscribedISDN selection



number parameter and with a Generic number parameter,sends a SETUP message without the Calling party number information element.


SETUP;Calling party number information element not present


IAM;Calling party number parameterGeneric number parameter


6.3.2.2 Connected Line Identification Presentation (COLP)

NOTE: The connected line identity request indicator of the Optional forward call indicators parameter in theIAM message has to be coded to "requested".

ISDN selection criteria: COLR not subscribed.





TSS reference: DSS1-ISUP/SS/COLP/Special ArrangementISDN selection


criteria:Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of a

CONNECT message with an invalid Connected number information element,sends a CON message with the Connected number parameter coded



values:CONNECT;invalid Connected number information element


CON;Connected number parameterAddress signals = PIXITNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameter not present

Comments: ISDN CONNECT -> SUT -> IAM CON

ETSI







CONNECT message with an invalid Connected number information element but with avalid Connected subaddress information element,

sends a CON message with the Connected number parameter codedAddress signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided,



CONNECT;invalid Connected number information elementConnected subaddress information element


CON;Connected number parameterAddress signals = PIXITNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameter not presentAccess transport parameter including the subaddress information






criteria:Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with an invalid

Connected number information element,sends an ANM message with the Connected number parameter coded





ANM;Connected number parameterAddress signals = PIXITNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameter not present

Comments: ISDN CONNECT -> SUT -> IAM ANM

ETSI







Connected number information element but with a valid Connected subaddressinformation element,

sends an ANM message with the Connected number parameter codedAddress signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided,





ANM;Connected number parameterAddress signals = PIXITNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameter not presentAccess transport parameter including the subaddress information







CONNECT message without the Connected number information element,sends a CON message with the Connected number parameter coded



values:CONNECT;Connected number information element not present




ETSI







CONNECT message without the Connected number information element but with a validConnected subaddress information element,




CONNECT;Connected number information element not presentConnected subaddress information element








criteria:Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message without the








ETSI















ETSI







CONNECT message with the Connected number information element codedType of number = national numberNumbering plan identification = ISDN_NPI,

sends a CON message with the Connected number parameter codedAddress signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided



CONNECT;Connected number information elementType of number = '010'BNumbering plan identification = ISDN_NPINumber digits = PIXIT2


CON;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '00'B


ETSI







CONNECT message with the Connected number information element codedType of number = national numberNumbering plan identification = ISDN_NPIand with a valid Connected subaddress information element,




values:CONNECT;Connected number information elementType of number = '010'BNumbering plan identification = ISDN_NPINumber digits = PIXIT2Connected subaddress information element


CON;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '00'BAccess transport parameter including the subaddress information


ETSI






criteria:Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with the Connected

number information element codedType of number = national numberNumbering plan identification = ISDN_NPI,

sends an ANM message with the Connected number parameter codedAddress signals = default numberNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = network provided





ANM;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '00'B


ETSI







number information element codedType of number = national numberNumbering plan identification = ISDN_NPIand with a valid Connected subaddress information element,






ANM;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '00'BAccess transport parameter including the subaddress information


ETSI







CONNECT message with the Connected number information element codedType of number = international numberNumbering plan identification = ISDN_NPI,






CON;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '00'B


ETSI







CONNECT message with the Connected number information element codedType of number = international numberNumbering plan identification = ISDN_NPIand with a valid Connected subaddress information element,






CON;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '00'BAccess transport parameter including the subaddress information


ETSI







number information element codedType of number = international numberNumbering plan identification = ISDN_NPI,






ANM;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '00'B


ETSI







number information element codedType of number = international numberNumbering plan identification = ISDN_NPIand with a valid Connected subaddress information element,






ANM;Connected number parameterAddress signals = PIXIT1Numbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '11'BGeneric number parameterAddress signals = PIXIT2Numbering plan indicator = '001'BNature of address indicator = '0000100'BScreening indicator = '00'BAccess transport parameter including the subaddress information



'0001'B-


ETSI



ISDN selection criteria: Special arrangement does apply.



TSS reference: DSS1-ISUP/SS/COLP/No Special ArrangementISDN selection



CONNECT message with an invalid Connected number information element,sends a CON message with the Connected number parameter coded












CONNECT message with an invalid Connected number information element but with avalid Connected subaddress information element,








ETSI



























ETSI







CONNECT message without the Connected number information element,sends a CON message with the Connected number parameter coded












CONNECT message without the Connected number information element but with a validConnected subaddress information element,








ETSI



























ETSI







Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of aCONNECT message with the Connected number information element, when a failure ofthe screening function occurs,



values:CONNECT;Connected number information element









Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of aCONNECT message with the Connected number information element, when a failure ofthe screening function occurs and with a valid Connected subaddress informationelement,




CONNECT;Connected number information elementConnected subaddress information element




ETSI







Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with a Connectednumber information element, when a failure of the screening function occurs,












Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with a Connectednumber information element, when a failure of the screening function occurs and with avalid Connected subaddress information element,




CONNECT;Connected number information elementConnected subaddress information element




ETSI







CONNECT message with the Connected number information element codedType of number = subscriber numberNumbering plan identification = ISDN_NPINumber digits = correct complete subscriber number,

sends a CON message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed


values:CONNECT;Connected number information elementType of number = '100'BNumbering plan identification = ISDN_NPINumber digits = PIXIT









CONNECT message with the Connected number information element codedType of number = subscriber numberNumbering plan identification = ISDN_NPINumber digits = correct complete subscriber numberand with a valid Connected subaddress information element,

sends a CON message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,



CONNECT;Connected number information elementType of number = '100'BNumbering plan identification = ISDN_NPINumber digits = PIXITConnected subaddress information element




ETSI







number information element codedType of number = subscriber numberNumbering plan identification = ISDN_NPINumber digits = correct complete subscriber number,

sends an ANM message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed






ETSI







number information element codedType of number = subscriber numberNumbering plan identification = ISDN_NPINumber digits = correct complete subscriber numberand with a valid Connected subaddress information element,

sends an ANM message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,












CONNECT message with the Connected number information element codedType of number = national numberNumbering plan identification = ISDN_NPINumber digits = correct complete national number,

sends a CON message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed






ETSI







CONNECT message with the Connected number information element codedType of number = national numberNumbering plan identification = ISDN_NPINumber digits = correct complete national numberand with a valid Connected subaddress information element,

sends a CON message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,







ETSI







number information element codedType of number = national numberNumbering plan identification = ISDN_NPINumber digits = correct complete national number,

sends an ANM message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed











number information element codedType of number = national numberNumbering plan identification = ISDN_NPINumber digits = correct complete national numberand with a valid Connected subaddress information element,

sends an ANM message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,







ETSI







CONNECT message with the Connected number information element codedType of number = international numberNumbering plan identification = ISDN_NPINumber digits = correct complete international number,

sends a CON message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, verified and passed






ETSI







CONNECT message with the Connected number information element codedType of number = international numberNumbering plan identification = ISDN_NPINumber digits = correct complete international numberand with a valid Connected subaddress information element,

sends a CON message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, verified and passed,












number information element codedType of number = international numberNumbering plan identification = ISDN_NPINumber digits = correct complete international number,

sends an ANM message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, verified and passed






ETSI







number information element codedType of number = international numberNumbering plan identification = ISDN_NPINumber digits = correct complete international numberand with a valid Connected subaddress information element,

sends an ANM message with the Connected number parameter codedAddress signals = number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = international numberScreening indicator = user provided, verified and passed,







ETSI







CONNECT message with the Connected number information element codedType of number = unknownNumbering plan identification = ISDN_NPINumber digits = incomplete number,

sends a CON message with the Connected number parameter codedAddress signals = completion of the number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed




CON;Connected number parameterAddress signals = PIXIT completedNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '01'BGeneric number parameter not present







CONNECT message with the Connected number information element codedType of number = unknownNumbering plan identification = ISDN_NPINumber digits = incomplete numberand with a valid Connected subaddress information element,

sends a CON message with the Connected number parameter codedAddress signals = completion of the number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,





CON;Connected number parameterAddress signals = PIXIT completedNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '01'BGeneric number parameter not presentAccess transport parameter including the subaddress information


ETSI







number information element codedType of number = unknownNumbering plan identification = ISDN_NPINumber digits = incomplete number,

sends an ANM message with the Connected number parameter codedAddress signals = completion of the number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed




ANM;Connected number parameterAddress signals = PIXIT completedNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '01'BGeneric number parameter not present


ETSI







number information element codedType of number = unknownNumbering plan identification = ISDN_NPINumber digits = incomplete numberand with a valid Connected subaddress information element,

sends an ANM message with the Connected number parameter codedAddress signals = completion of the number provided by the userNumbering plan indicator = ISDN numbering planNature of address indicator = national numberScreening indicator = user provided, verified and passed,





ANM;Connected number parameterAddress signals = PIXIT completedNumbering plan indicator = '001'BNature of address indicator = '0000011'BScreening indicator = '01'BGeneric number parameter not presentAccess transport parameter including the subaddress information



'0001'B-


6.3.2.3 Connected Line Identification Restriction (COLR)

ISDN selection criteria: COLR subscribed.

ETSI







criteria:COLR permanent mode


Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of aCONNECT message with a valid Connected number information element,

sends a CON message with the Connected number parameter and the Genericnumber parameter coded

Address presentation restriction indicator = presentation restricted.ISDN Parameter



CON;Connected number parameter and Generic number parameterAddress presentation restriction indicator = '01'B







Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with a validConnected number information element,

sends an ANM message with the Connected number parameter and the Genericnumber parameter coded




ANM;Connected number parameter and Generic number parameterAddress presentation restriction indicator = '01'B





criteria:COLR temporary mode, default setting = restricted


Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of aCONNECT message with a valid Connected number information element codedPresentation indicator = ISDN_PRI,


Address presentation restriction indicator = ISUP_PRI.ISDN Parameter

values:CONNECT;Connected number information elementPresentation indicator = ISDN_PRI


CON;Connected number parameter and Generic number parameterAddress presentation restriction indicator = ISUP_PRI


ETSI







Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with a validConnected number information element codedPresentation indicator = ISDN_PRI,





ANM;Connected number parameter and Generic number parameterAddress presentation restriction indicator = ISUP_PRI


Values for the test purpose TP603103 - TP603104VA_01 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'BVA_02 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'B






Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of aCONNECT message with a valid Connected number information element not includingthe optional octet 3a (screening and presentation indicator),



values:CONNECT;Connected number information elementPresentation indicator not present




ETSI







Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with a validConnected number information element not including the optional octet 3a (screeningand presentation indicator),










criteria:COLR temporary mode, default setting = allowed







CON;Connected number parameter and Generic number parameterAddress presentation restriction indicator = ISUP_PRI












ANM;Connected number parameter and Generic number parameterAddress presentation restriction indicator = ISUP_PRI


ETSI


Values for the test purpose TP603107 - TP603108VA_01 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'BVA_02 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'B








Address presentation restriction indicator = presentation allowed.ISDN Parameter












Address presentation restriction indicator = presentation allowed.ISDN Parameter





ETSI



ISDN selection criteria: Special arrangement does not apply.






Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of aCONNECT message with a valid Connected number information element,

sends a CON message with the Connected number parameter codedAddress presentation restriction indicator = presentation restricted




CON;Connected number parameterAddress presentation restriction indicator = '01'BGeneric number parameter not present







Test purpose: Ensure that the SUT in state N7, on receipt of a CONNECT message with a validConnected number information element,

sends an ANM message with the Connected number parameter codedAddress presentation restriction indicator = presentation restricted




ANM;Connected number parameterAddress presentation restriction indicator = '01'BGeneric number parameter not present


ETSI








sends a CON message with the Connected number parameter codedAddress presentation restriction indicator = ISUP_PRI




CON;Connected number parameterAddress presentation restriction indicator = ISUP_PRIGeneric number parameter not present








sends an ANM message with the Connected number parameter codedAddress presentation restriction indicator = ISUP_PRI




ANM;Connected number parameterAddress presentation restriction indicator = ISUP_PRIGeneric number parameter not present


Values for the test purpose TP603203 - TP603204VA_01 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'BVA_02 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'B

ETSI








sends a CON message with the Connected number parameter codedAddress presentation restriction indicator = presentation restricted












sends an ANM message with the Connected number parameter codedAddress presentation restriction indicator = presentation restricted






ETSI








sends a CON message with the Connected number parameter codedAddress presentation restriction indicator = ISUP_PRI




CON;Connected number parameterAddress presentation restriction indicator = ISUP_PRIGeneric number parameter not present








sends an ANM message with the Connected number parameter codedAddress presentation restriction indicator = ISUP_PRI




ANM;Connected number parameterAddress presentation restriction indicator = ISUP_PRIGeneric number parameter not present


Values for the test purpose TP603207 - TP603208VA_01 ISDN_PRI =presentation allowed, '00'B ISUP_PRI =presentation allowed, '00'BVA_02 ISDN_PRI =presentation restricted, '01'B ISUP_PRI =presentation restricted, '01'B

ETSI








sends a CON message with the Connected number parameter codedAddress presentation restriction indicator = presentation allowed












sends an ANM message with the Connected number parameter codedAddress presentation restriction indicator = presentation allowed






6.3.2.4 Subaddressing (SUB)



TSS reference: DSS1-ISUP/SS/SUBISDN selection

criteria:Subaddressing subscribed


Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the subaddressinformation in the Access transport parameter,

sends a SETUP message with a Called party subaddress information element.ISDN Parameter

values:SETUP;Called party subaddress information element


IAM;Access transport parameter including the subaddress information


ETSI


6.3.2.5 Call Diversion (CDIV)



TSS reference: ISUP-DSS1/SS/CDIVISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of a IAM message with the Redirection

information parameter codedRedirection counter = 1Redirecting reason = ISUP_RRand the Original called number parameter codedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,

sends a SETUP message with the Redirecting number information element codedType of number = national number or unknownNumbering plan identification = ISDN/Telephony numbering plan or unknownPresentation indicator = presentation allowedReason for diversion = ISDN_RFDNumber digits included.


SETUP;Redirecting number information elementType of number = '010'B or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = ISDN_RFDNumber digits = PIXIT


IAM;Redirection information parameterRedirection counter = '001'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = '0000011'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter = 1Redirecting reason = ISUP_RRand the Original called number parameter codedNature of address indicator = international numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,

sends a SETUP message with the Redirecting number information element codedType of number = international number or unknownNumbering plan identification = ISDN/Telephony numbering plan or unknownPresentation indicator = presentation allowedReason for diversion = ISDN_RFDNumber digits included.


SETUP;Redirecting number information elementType of number = '001'B or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = ISDN_RFDNumber digits = PIXIT


IAM;Redirection information parameterRedirection counter = '001'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = '0000100'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter = 1Redirecting reason = ISUP_RRand the Original called number parameter codedAddress presentation restricted parameter = presentation restricted,

sends a SETUP message with the Redirecting number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = presentation restrictedReason for diversion = ISDN_RFDNumber digits not included.


SETUP;Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BReason for diversion = ISDN_RFDNumber digits not included


IAM;Redirection information parameterRedirection counter = '001'BRedirecting reason = ISUP_RROriginal called number parameterAddress presentation restricted parameter = '01'B







information parameter codedRedirection counter = 1Redirecting reason = ISUP_RRand the Original called number parameter codedAddress presentation restricted parameter = address not available,

sends a SETUP message with the Redirecting number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingReason for diversion = ISDN_RFDNumber digits not included.




IAM;Redirection information parameterRedirection counter = '001'BRedirecting reason = ISUP_RROriginal called number parameterAddress presentation restricted parameter = '10'B


ETSI







information parameter codedRedirection counter = 1Redirecting reason = ISUP_RRand without the Original called number parameter,

sends a SETUP message with the Redirecting number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingReason for diversion = ISDN_RFDNumber digits not included.




IAM;Redirection information parameterRedirection counter = '001'BRedirecting reason = ISUP_RROriginal called number parameter not present


Values for the test purpose TP605001 - TP605005VA_01 ISDN_RFD = Unknown, '0000'B ISUP_RR = unknown, '0000'BVA_02 ISDN_RFD = Call forwarding busy, '0001'B ISUP_RR = user busy, '0001'BVA_03 ISDN_RFD = Call forwarding no reply, '0010'B ISUP_RR = no reply, '0010'BVA_04 ISDN_RFD = Call forwarding unconditional,

'1111'BISUP_RR = unconditional, '0011'B

VA_05 ISDN_RFD = Call deflection, '1010'B ISUP_RR = deflection during alerting, '0100'BVA_06 ISDN_RFD = Call deflection, '1010'B ISUP_RR = deflection immediate response,

'0101'B

ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals includedand the Redirecting number parameter codedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,

sends a SETUP message with the first Redirecting number information elementcoded

Type of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering plan or unknownPresentation indicator = presentation allowedReason for diversion = unknownNumber digits included

and the second Redirecting number information element codedType of number = national number or unknownNumbering plan identification = ISDN/Telephony numbering plan or unknownPresentation indicator = presentation allowedReason for diversion = ISDN_RFDNumber digits included.


SETUP;First Redirecting number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = '0000'BNumber digits = PIXITSecond Redirecting number information elementType of number = '010'B or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = ISDN_RFDNumber digits = PIXIT


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXITRedirecting number parameterNature of address indicator = '0000011'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals includedand the Redirecting number parameter codedNature of address indicator = international numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,



and the second Redirecting number information element codedType of number = international number or unknownNumbering plan identification = ISDN/Telephony numbering plan or unknownPresentation indicator = presentation allowedReason for diversion = ISDN_RFDNumber digits included.


SETUP;First Redirecting number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = '0000'BNumber digits = PIXITSecond Redirecting number information elementType of number = '001'B or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = ISDN_RFDNumber digits = PIXIT


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXITRedirecting number parameterNature of address indicator = '0000100'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals includedand the Redirecting number parameter codedAddress presentation restricted parameter = presentation restricted,



and the second Redirecting number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = presentation restrictedReason for diversion = ISDN_RFDNumber digits not included.


SETUP;First Redirecting number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = '0000'BNumber digits = PIXITSecond Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BReason for diversion = ISDN_RFDNumber digits not present


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXITRedirecting number parameterAddress presentation restricted parameter = '01'B


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals includedand the Redirecting number parameter codedAddress presentation restricted parameter = address not available,



and the second Redirecting number information element codedType of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingReason for diversion = ISDN_RFDNumber digits not included.


SETUP;First Redirecting number information elementType of number = ISDN_TON or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = '0000'BNumber digits = PIXITSecond Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '10'BReason for diversion = ISDN_RFDNumber digits not present


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXITRedirecting number parameterAddress presentation restricted parameter = '10'B


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals includedand without the Redirecting number parameter,





SETUP;First Redirecting number information elementType of number = ISDN_TON or '000'BNumbering plan identification ='0001'B or '0000'BPresentation indicator = '00'BReason for diversion = '0000'BNumber digits = PIXITSecond Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '10'BReason for diversion = ISDN_RFDNumber digits not present


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXITRedirecting number parameter not present


ETSI


Values for the test purpose TP605006 - TP605010VA_01 ISDN_TON = national number, '010'B

ISDN_RFD = Unknown, '0000'BISUP_NAI = national number, '0000011'BISUP_RR = unknown, '0000'B

VA_02 ISDN_TON = national number, '010'BISDN_RFD = Call forwarding busy, '0001'B

ISUP_NAI = national number, '0000011'BISUP_RR = user busy, '0001'B

VA_03 ISDN_TON = national number, '010'BISDN_RFD = Call forwarding no reply, '0010'B

ISUP_NAI = national number, '0000011'BISUP_RR = no reply, '0010'B

VA_04 ISDN_TON = national number, '010'BISDN_RFD = Call forwarding unconditional,'1111'B

ISUP_NAI = national number, '0000011'BISUP_RR = unconditional, '0011'B

VA_05 ISDN_TON = national number, '010'BISDN_RFD = Call deflection, '1010'B

ISUP_NAI = national number, '0000011'BISUP_RR = deflection during alerting, '0100'B

VA_06 ISDN_TON = national number, '010'BISDN_RFD = Call deflection, '1010'B

ISUP_NAI = national number, '0000011'BISUP_RR = deflection immediate response,'0101'B

VA_07 ISDN_TON = international number, '001'BISDN_RFD = Unknown, '0000'B

ISUP_NAI = international number, '0000100'BISUP_RR = unknown, '0000'B

VA_08 ISDN_TON = international number, '001'BISDN_RFD = Call forwarding busy, '0001'B

ISUP_NAI = international number, '0000100'BISUP_RR = user busy, '0001'B

VA_09 ISDN_TON = international number, '001'BISDN_RFD = Call forwarding no reply, '0010'B

ISUP_NAI = international number, '0000100'BISUP_RR = no reply, '0010'B

VA_10 ISDN_TON = international number, '001'BISDN_RFD = Call forwarding unconditional,'1111'B

ISUP_NAI = international number, '0000100'BISUP_RR = unconditional, '0011'B

VA_11 ISDN_TON = international number, '001'BISDN_RFD = Call deflection, '1010'B

ISUP_NAI = international number, '0000100'BISUP_RR = deflection during alerting, '0100'B

VA_12 ISDN_TON = international number, '001'BISDN_RFD = Call deflection, '1010'B

ISUP_NAI = international number, '0000100'BISUP_RR = deflection immediate response,'0101'B

ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = presentation restrictedand the Redirecting number parameter codedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,


Type of number = unknownNumbering plan identification = unknownPresentation indicator = presentation restrictedReason for diversion = unknownNumber digits not included



SETUP;First Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BReason for diversion = '0000'BNumber digits not presentSecond Redirecting number information elementType of number = '010'B or '000'BNumbering plan identification = '0001'B or '0000'BPresentation indicator = '00'BReason for diversion = ISDN_RFDNumber digits = PIXIT


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterAddress presentation restricted parameter = '01'BRedirecting number parameterNature of address indicator = '0000011'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = presentation restrictedand the Redirecting number parameter codedNature of address indicator = international numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,









ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = presentation restrictedand the Redirecting number parameter codedAddress presentation restricted parameter = presentation restricted,





SETUP;First Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BReason for diversion = '0000'BNumber digits not presentSecond Redirecting number information elementType of number = '000'BNumbering plan identification = '0000'BPresentation indicator = '01'BReason for diversion = ISDN_RFDNumber digits not present


IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterAddress presentation restricted parameter = '01'BRedirecting number parameterAddress presentation restricted parameter = '01'B


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = presentation restrictedand the Redirecting number parameter codedAddress presentation restricted parameter = address not available,









ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = presentation restrictedand without the Redirecting number parameter,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterAddress presentation restricted parameter = '01'BRedirecting number parameter not present


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = address not availableand the Redirecting number parameter codedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,


Type of number = unknownNumbering plan identification = unknownPresentation indicator = number not available due to interworkingReason for diversion = unknownNumber digits not included







ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = address not availableand the Redirecting number parameter codedNature of address indicator = international numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,









ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = address not availableand the Redirecting number parameter codedAddress presentation restricted parameter = presentation restricted,









ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = address not availableand the Redirecting number parameter codedAddress presentation restricted parameter = address not available,









ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,the Original called number parameter codedAddress presentation restricted parameter = address not availableand without the Redirecting number parameter,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameterAddress presentation restricted parameter = '10'BRedirecting number parameter not present


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,without the Original called number parameterand the Redirecting number parameter codedNature of address indicator = national numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameter not presentRedirecting number parameterNature of address indicator = '0000011'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,without the Original called number parameterand the Redirecting number parameter codedNature of address indicator = international numberNumbering plan indicator = ISDN/Telephony numbering planAddress presentation restricted parameter = presentation allowedAddress signals included,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameter not presentRedirecting number parameterNature of address indicator = '0000100'BNumbering plan indicator = '001'BAddress presentation restricted parameter = '00'BAddress signals = PIXIT


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,without the Original called number parameterand the Redirecting number parameter codedAddress presentation restricted parameter = presentation restricted,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameter not presentRedirecting number parameterAddress presentation restricted parameter = '01'B


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,without the Original called number parameterand the Redirecting number parameter codedAddress presentation restricted parameter = address not available,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameter not presentRedirecting number parameterAddress presentation restricted parameter = '10'B


ETSI







information parameter codedRedirection counter > 1Redirecting reason = ISUP_RR,without the Original called number parameterand without the Redirecting number parameter,







IAM;Redirection information parameterRedirection counter = '010'BRedirecting reason = ISUP_RROriginal called number parameter not presentRedirecting number parameter not present


Values for the test purpose TP605011 - TP605025VA_01 ISDN_RFD = Unknown, '0000'B ISUP_RR = unknown, '0000'BVA_02 ISDN_RFD = Call forwarding busy, '0001'B ISUP_RR = user busy, '0001'BVA_03 ISDN_RFD = Call forwarding no reply, '0010'B ISUP_RR = no reply, '0010'BVA_04 ISDN_RFD = Call forwarding unconditional,

'1111'BISUP_RR = unconditional, '0011'B

VA_05 ISDN_RFD = Call deflection, '1010'B ISUP_RR = deflection during alerting, '0100'BVA_06 ISDN_RFD = Call deflection, '1010'B ISUP_RR = deflection immediate response,

'0101'B

ETSI


6.3.2.6 Call Waiting (CW)

ISDN selection criteria: CW subscribed.


ISDN selection criteria: Notification is delivered, S/T reference point.



TSS reference: ISUP-DSS1/SS/CW/S T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N6, having sent a SETUP message with the

Channel identification information element codedInformation channel selection = no channel,on receipt of an ALERTING message,

sends an ACM message with the Generic notification indicator parameter codedNotification indicator = call is a waiting call.


SETUP;Channel identification information elementInformation channel selection = '00'BALERTING;


ACM;Generic notification indicator parameterNotification indicator = '1100000'B

Comments: ALERTING ISDN -> SUT -> ISUP ACM













ETSI








sends a CPG message with the Generic notification indicator parameter codedNotification indicator = call is a waiting call.





Comments: ALERTING ISDN -> SUT -> ISUP CPG





TSS reference: ISUP-DSS1/SS/CW/T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N6, on receipt of an ALERTING message with the

Notification indicator information element codedNotification description = call is a waiting call,



ALERTING;Notification indicator information elementNotification description = '1100000'B




ETSI

























Comments: ALERTING ISDN -> SUT -> ISUP CPG





criteria:Test purpose: Ensure that the SUT in state N7 on receipt of a PROGRESS message with the Notification

indicator information element codedNotification description = call is a waiting call,



PROGRESS;Notification indicator information elementNotification description = '1100000'B



Comments: PROGRESS ISDN -> SUT -> ISUP CPG

ETSI







indicator information element codedNotification description = call is a waiting call,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = call is a waiting call

and the Event information parameter codedEvent indicator = PROGRESS





Comments: NOTIFY ISDN -> SUT -> ISUP CPG

6.3.2.7 Call Hold (HOLD)




TSS reference: ISUP-DSS1/SS/HOLD/From networkISDN selection










ETSI






































ETSI



ISDN selection criteria: Call Hold subscribed, S/T reference point.



TSS reference: ISUP-DSS1/SS/HOLD/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a HOLD message,




HOLD;






TSS reference: ISUP-DSS1/SS/HOLD/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a RETRIEVE message,




HOLD;




ETSI






TSS reference: ISUP-DSS1/SS/HOLD/Notification TISDN selection



indicator information element codedNotification description = Remote hold,










TSS reference: ISUP-DSS1/SS/HOLD/Notification TISDN selection



indicator information element codedNotification description = Remote retrieval,








ETSI


6.3.2.8 Terminal Portability (TP)




TSS reference: ISUP-DSS1/SS/TP/From networkISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a SUS message with the Suspend/resume







Comments: ISUP SUS -> SUT -> NOTIFY ISDN





criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a RES message with the Suspend/resume







Comments: ISUP RES -> SUT -> NOTIFY ISDN






notification indicator parameter codedNotification indicator = user suspended,







ETSI







notification indicator parameter codedNotification indicator = user resumed,








ISDN selection criteria: Terminal Portability subscribed, S/T reference point.



TSS reference: ISUP-DSS1/SS/TP/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a SUSPEND message,

sends a SUS message with the Suspend/resume indicators parameter codedSuspend resume indicator = ISDN subscriber initiated,.


SUSPEND;



Comments: ISDN SUSPEND -> SUT -> SUS ISUP



TSS reference: ISUP-DSS1/SS/TP/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT in state N0, on receipt of a RESUME message,

sends a RES message with the Suspend/resume indicators parameter codedSuspend resume indicator = ISDN subscriber initiated,.


RESUME;



Comments: ISDN RESUME -> SUT -> RES ISUP

ETSI






TSS reference: ISUP-DSS1/SS/TP/Notification TISDN selection



indicator information element codedNotification description = user suspended,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = user suspended









TSS reference: ISUP-DSS1/SS/TP/Notification TISDN selection



indicator information element codedNotification description = user resumed,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = user resumed







ETSI


6.3.2.9 Conference Calling (CONF)




TSS reference: ISUP-DSS1/SS/CONF/From networkISDN selection



























notification indicator parameter codedNotification indicator = Other party added,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party added.






ETSI







notification indicator parameter codedNotification indicator = Isolated,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Isolated.











notification indicator parameter codedNotification indicator = Reattached,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Reattached.











notification indicator parameter codedNotification indicator = Other party isolated,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party isolated.






ETSI







notification indicator parameter codedNotification indicator = Other party reattached,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party reattached.











notification indicator parameter codedNotification indicator = Other party split,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party split.











notification indicator parameter codedNotification indicator = Other party disconnected,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Other party disconnected.






ETSI







notification indicator parameter codedNotification indicator = Conference floating,



values:CPG;Generic notification indicator parameterNotification indicator = '1001011'B



ISDN selection criteria: Conference Calling subscribed, S/T reference point.



TSS reference: ISUP-DSS1/SS/CONF/Invocation S TISDN selection



information element containing a BeginCONF invoke component,sends a CPG message with the Generic notification indicator parameter coded

Notification indicator = Conference established.ISDN Parameter

values:FACILITY;Facility information elementComponent = BeginCONF invoke component




ETSI






criteria:Test purpose: Ensure that the SUT with two calls in state N10 (towards remote users A and user B;

conference has been established with the call towards user A), on receipt of a FACILITYmessage for remote user B with the Facility information element containing a AddCONFinvoke component,


Notification indicator = Conference establishedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party added.


FACILITY;Facility information elementComponent = AddCONF invoke component









receipt of a FACILITY message with the Facility information element containing aAddCONF invoke componentPartyId = user B,


Notification indicator = Isolatedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party isolated.






ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (conference established, remote users A and user B, user

B isolated), on receipt of a FACILITY message with the Facility information elementcontaining a ReattachCONF invoke componentPartyId = user B,


Notification indicator = Reattachedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party reattached.











receipt of a FACILITY message with the Facility information element containing aSplitCONF invoke componentPartyId = user B,


Notification indicator = Conference disconnectedand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party split.






ETSI







receipt of a FACILITY message with the Facility information element containing aDropCONF invoke componentPartyId = user B,

sends towards user B a REL messageand sends towards user A a CPG message with the Generic notification indicator

parameter codedNotification indicator = Other party disconnected.




User B: REL;User A: CPG;Generic notification indicator parameterNotification indicator = '1001010'B

Comments: ISDN FACILITY -> SUT -> REL ISUP (B), CPG ISUP (A)






receipt of a DISCONNECT message,sends towards user B a REL messageand sends towards user A a REL message.


DISCONNECT;


User B: REL;User A: REL;

Comments: ISDN DISCONNECT -> SUT -> 2 REL ISUP

ETSI






TSS reference: ISUP-DSS1/SS/CONF/Notification TISDN selection
























ETSI







indicator information element codedNotification description = Other party added,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party added












indicator information element codedNotification description = Isolated,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Isolated







ETSI







indicator information element codedNotification description = Reattached,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Reattached












indicator information element codedNotification description = Other party isolated,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party isolated







ETSI







indicator information element codedNotification description = Other party reattached,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party reattached












indicator information element codedNotification description = Other party split,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party split







ETSI







indicator information element codedNotification description = Other party disconnected,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = Other party disconnected







6.3.2.10 Three-party (3PTY)




TSS reference: ISUP-DSS1/SS/3PTY/From networkISDN selection










ETSI



















notification indicator parameter codedNotification indicator = remote hold,

sends a NOTIFY message with the Notification indicator information element codedNotification description = remote hold.






ETSI






criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a CPG message with one Generic

notification indicator parameter codedNotification indicator = Conference disconnectedand another Generic notification indicator parameter codedNotification indicator = remote hold,,

sends two Notification indicator information elements in either one or two NOTIFYmessages, one coded

Notification description = Conference disconnectedand the other coded

Notification description = remote hold.ISDN Parameter

values:One or two NOTIFYsNotification indicator information elementNotification description = '1000011'BNotification indicator information elementNotification description = '1111001'B


CPG;Generic notification indicator parameterNotification indicator = '1000011'BGeneric notification indicator parameterNotification indicator = '1111001'B

Comments: ISUP CPG -> SUT -> 1 or 2 NOTIFY ISDN


ISDN selection criteria: Three-party subscribed, S/T reference point.

NOTE 1: User A: served user; users B and C: remote users.

NOTE 2: Call A-B: Active-held connection; Call A-C: Active-idle connection.



TSS reference: ISUP-DSS1/SS/3PTY/Invocation S TISDN selection


criteria:Test purpose: Ensure that the SUT with two calls in state N10 (towards remote users B and user C), on

receipt of a FACILITY message for call A-B with the Facility information elementcontaining a Begin3PTY invoke component,


Notification indicator = Conference establishedand sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = Conference established.


FACILITY;Facility information elementComponent = Begin3PTY invoke component




ETSI







conference has been established), on receipt of a FACILITY message for call A-B with theFacility information element containing an End3PTY invoke component,














conference has been disconnected), on receipt of a HOLD message for call A-C,sends no message towards user Band sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = remote hold.


HOLD;


User B: -;User C: CPG;Generic notification indicator parameterNotification indicator = '1111001'B


ETSI







conference has been disconnected, call A-C has been put on hold), on receipt of aRETRIEVE message for call A-B,


Notification indicator = Conference disconnectedand sends no message towards user C.


RETRIEVE;


User B: CPG;Generic notification indicator parameterNotification indicator = '1000011'BUser C: -;







conference has been established), on receipt of a FACILITY message for call A-C with theFacility information element containing an End3PTY invoke component,

sends towards user B a CPG message with one Generic notification indicatorparameter coded

Notification indicator = Conference disconnected,the other Generic notification indicator parameter coded






User B: CPG;Generic notification indicator parameterNotification indicator = '1000011'BGeneric notification indicator parameterNotification indicator = '1111001'BUser C: CPG;Generic notification indicator parameterNotification indicator = '1000011'B


ETSI







conference has been established), on receipt of a DISCONNECT message for call A-B,sends towards user B a REL message and sends towards user C a CPG message with

the Generic notification indicator parameter codedNotification indicator = Conference disconnected.


DISCONNECT;



Comments: ISDN FACILITY -> SUT -> REL ISUP (B), CPG ISUP (C)






conference has been established), on receipt of a DISCONNECT message for call A-C,sends towards user B a CPG message with the Generic notification indicator


and sends towards user C a REL message.ISDN Parameter

values:DISCONNECT;



Comments: ISDN FACILITY -> SUT -> CPG ISUP (B), REL ISUP (C)





criteria:Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B, call towards user C

has been disconnected; 3PTY conference had been established), on receipt of aRETRIEVE message for call A-B,



values:RETRIEVE;




ETSI







conference has been established), on receipt of a REL message from user B,sends towards user C a CPG message with the Generic notification indicator

parameter codedNotification indicator = Conference disconnected

and sends a DISCONNECT message for call A-B.ISDN Parameter

values:DISCONNECT;



Comments: ISUP REL (B) -> SUT -> DISCONNECT ISDN (A-B), CPG ISUP (C)






conference has been established), on receipt of a REL message from user C,sends towards user B a CPG message with the Generic notification indicator


and sends a DISCONNECT message for call A-C.ISDN Parameter

values:DISCONNECT;



Comments: ISUP REL (C) -> SUT -> DISCONNECT ISDN (A-C), CPG ISUP (B)





criteria:Test purpose: Ensure that the SUT with one call in state N10 (towards remote user B, user C has

disconnected; 3PTY conference had been established), on receipt of a RETRIEVEmessage for call A-B,



values:RETRIEVE;


User B: REL;Generic notification indicator parameterNotification indicator = '1000011'BUser C: -;


ETSI






TSS reference: ISUP-DSS1/SS/3PTY/Notification TISDN selection
























ETSI







indicator information element codedNotification description = remote hold,

sends a CPG message with the Generic notification indicator parameter codedNotification indicator = remote hold







6.3.2.11 Closed User Group (CUG)

6.3.2.11.1 CUG subscribed

ISDN selection criteria: CUG subscribed.



TSS reference: ISUP-DSS1/SS/CUGISDN selection


criteria:Test purpose: Ensure that the SUT in state N9 (CUG call), on receipt of a DISCONNECT message with

the Facility information element containing a CUGCall return error component codedError value = ISDN_EV,

sends a REL message with the Cause indicators parameter codedCause value = ISUP_CV.


DISCONNECT;Facility information elementComponent = CUGCall return errorError value = ISDN_EV


REL;Cause indicators parameterCause value = ISUP_CV

Comments: ISDN DISCONNECT -> SUT -> ISUP REL

ETSI






criteria:Test purpose: Ensure that the SUT in state N9 (CUG call), on receipt of a RELEASE message with the

Facility information element containing a CUGCall return error component codedError value = ISDN_EV,



RELEASE;Facility information elementComponent = CUGCall return errorError value = ISDN_EV



Comments: ISDN RELEASE -> SUT -> ISUP REL





criteria:Test purpose: Ensure that the SUT in state N6 (CUG call), on receipt of a RELEASE COMPLETE

message with the Facility information element containing a CUGCall return errorcomponent codedError value = ISDN_EV,



RELEASE COMPLETE;Facility information elementComponent = CUGCall return errorError value = ISDN_EV



Comments: ISDN RELEASE COMPLETE -> SUT -> ISUP REL

Values for the test purpose TP611101 - TP611103VA_01 ISDN_EV= userNotMemberOfCUG, 20 ISUP_CV = 87, User not member of CUG,

'1010111'BVA_02 ISDN_EV= invalidOrUnregisteredCUGIndex, 16 ISUP_CV = 87, User not member of CUG,

'1010111'BVA_03 ISDN_EV=

requestedBasicServiceViolatesCUGConstraints,17

ISUP_CV = 87, User not member of CUG,'1010111'B

VA_04 ISDN_EV= incomingCallsBarredWithinCUG, 19 ISUP_CV = 55, Incoming calls barred withinCUG, '0110111'B

ETSI






criteria:Test purpose: Ensure that the SUT in state N9 (CUG call), on receipt of a DISCONNECT message with

the Facility information element containing a CUGCall return error component codedError value = ISDN_EV,

sends a REL message.ISDN Parameter

values:DISCONNECT;Facility information elementComponent = CUGCall return errorError value = ISDN_EV


REL;






criteria:Test purpose: Ensure that the SUT in state N9 (CUG call), on receipt of a RELEASE message with the

Facility information element containing a CUGCall return error component codedError value = ISDN_EV,


values:RELEASE;Facility information elementComponent = CUGCall return errorError value = ISDN_EV


REL;







message with the Facility information element containing a CUGCall return errorcomponent codedError value = ISDN_EV,


values:RELEASE COMPLETE;Facility information elementComponent = CUGCall return errorError value = ISDN_EV


REL;


Values for the test purpose TP611104 - TP611106VA_01 ISDN_EV=

inconsistencyInDesignatedFacilityAndSubscriberClass, 21

-

VA_02 ISDN_EV= basicServiceNotProvided, 8 -

ETSI






criteria:Test purpose: Ensure that the SUT in state N9 (CUG call), on receipt of a DISCONNECT message without

a Facility information element containing a CUGCall return error component,sends a REL message.


DISCONNECT;Facility information element with CUGCall return error not present


REL;






criteria:Test purpose: Ensure that the SUT in state N9 (CUG call), on receipt of a RELEASE message without a

Facility information element containing a CUGCall return error component,sends a REL message.


RELEASE;Facility information element with CUGCall return error not present


REL;







message without a Facility information element containing a CUGCall return errorcomponent,


values:RELEASE COMPLETE;Facility information element with CUGCall return error not present


REL;


ETSI



ISUP reference:ETS 300 356-9 [12], table 1-4


criteria:CUG subscription option: Barring within the CUG <> incoming call


Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the Optionalforward call indicators parameter codedClosed user group call indicator = ISUP_CUGCIand with the Closed user group interlock code parameter giving an interlock code of aCUG the ISDN access belongs to,

sends a SETUP message with a Facility information element containing a CUGCallinvoke component.


SETUP;Facility information elementComponent = CUGCall invoke component


IAM;Optional forward call indicators parameterClosed user group call indicator = ISUP_CUGCIClosed user group interlock code parameter = PIXIT

Comments: ISUP IAM -> SUT -> ISDN SETUP

Values for the test purposes TP611110VA_01 - ISUP_CUGCI = closed user group call, outgoing

access not allowed, '11'BVA_02 - ISUP_CUGCI = closed user group call, outgoing

access allowed, '10'BComments: The above test case has to be tested for the following subscription options available per ISDN

number (see EN 300 138-2 [30]; table 1):1. Incoming access = Not allowed2. Incoming access = Allowed




criteria:ISDN number subscription option: Incoming access = allowed ANDCUG subscription option: Barring within the CUG = incoming call


Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the Optionalforward call indicators parameter codedClosed user group call indicator = closed user group call, outgoing access allowedand with the Closed user group interlock code parameter giving an interlock code of aCUG the ISDN access belongs to,

sends a SETUP message without a Facility information element containing aCUGCall invoke component.


SETUP;Facility information element with CUGCall invoke component not present


IAM;Optional forward call indicators parameterClosed user group call indicator = '10'BClosed user group interlock code parameter = PIXIT


ETSI





criteria:ISDN number subscription option: Incoming access = allowed


Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the Optionalforward call indicators parameter codedClosed user group call indicator = closed user group call, outgoing access allowedand with the Closed user group interlock code parameter giving an interlock code of aCUG the ISDN access does not belong to,





IAM;Optional forward call indicators parameterClosed user group call indicator = '10'BClosed user group interlock code parameter = PIXIT





criteria:ISDN number subscription option: Incoming access = allowed


Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the Optionalforward call indicators parameter codedClosed user group call indicator = non-CUG calland without the Closed user group interlock code parameter,





IAM;Optional forward call indicators parameterClosed user group call indicator = '00'BClosed user group interlock code parameter not present


Values for the test purposes TP611012 and TP611013Comments: The above test cases have to be tested for the following subscription options available per CUG

(see EN 300 138-2 [30]; table 2):1. Barring within the CUG <> Incoming call2. Barring within the CUG = Incoming call

ETSI


6.3.2.11.2 CUG not subscribed

ISDN selection criteria: CUG not subscribed.





criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the Optional

forward call indicators parameter codedClosed user group call indicator = closed user group call, outgoing access allowedand with the Closed user group interlock code parameter,





IAM;Optional forward call indicators parameterClosed user group call indicator = '10'BClosed user group interlock code parameter


6.3.2.12 User User Signalling (UUS)

6.3.2.12.1 Service 1 (UUS1) implicit

ISDN selection criteria: UUS1 implicit subscribed.



TSS reference: ISUP-DSS1/SS/UUS/UUS1 implicitISDN selection


criteria:Test purpose: Ensure that the SUT in the Idle state, on receipt of an IAM message with the User-to-user

parameter without user information,sends a SETUP message with a User-user information element without user

information.ISDN Parameter

values:SETUP;User-user information elementUser information not present


IAM;User-to-user parameterUser information not present


ETSI







parameter with user information,sends a SETUP message with a User-user information element with user information.


SETUP;User-user information elementUser information present


IAM;User-to-user parameterUser information present






criteria:Test purpose: Ensure that the SUT in state N6 (UUS1 has been activated), not having sent the ACM

message, on receipt of an ALERTING message with a User-user information element,sends an ACM message with the User-to-user parameter.


ALERTING;User-user information element


ACM;User-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N9 (UUS1 has been activated), on receipt of an ALERTING

message with a User-user information element,sends a CPG message with the User-to-user parameter.


ALERTING;User-user information element


CPG;User-to-user parameter


ETSI






criteria:Test purpose: Ensure that the SUT in state N6 (UUS1 has been activated), not having sent the ACM

message, on receipt of a CONNECT message with a User-user information element,sends a CON message with the User-to-user parameter.




CON;User-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N7 (UUS1 has been activated), on receipt of a CONNECT

message with a User-user information element,sends an ANM message with the User-to-user parameter.




























ETSI














































ETSI





criteria:S/T reference point


Test purpose: Ensure that the SUT in state N7 (UUS1 has been activated), on receipt of a REL messagewith a User-to-user parameter,

sends a RELEASE message with a User-user information element.ISDN Parameter

values:RELEASE;User-user information element










sends a DISCONNECT message with a User-user information element.ISDN Parameter

values:DISCONNECT;User-user information element















ETSI


6.3.2.12.2 Service 1 (UUS1) explicit

ISDN selection criteria: UUS1 explicit subscribed.



TSS reference: ISUP-DSS1/SS/UUS/UUS1 explicitISDN selection



indicators parameter codedType = requestService 1 = request, not essentialService 2 = no informationService 3 = no informationand without the User-to-user parameter,

sends a SETUP message with a Facility information element containing aUserUserService invoke component coded

Service = Service1Preferred = preferred request

and without the User-user information element.ISDN Parameter

values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = TrueUser-user information element not present


IAM;User-to-user indicators parameterType = '0'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter not present


ETSI







indicators parameter codedType = requestService 1 = request, not essentialService 2 = no informationService 3 = no informationand with the User-to-user parameter,


Service = Service1Preferred = preferred request

and with the User-user information element.ISDN Parameter

values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = TrueUser-user information element


IAM;User-to-user indicators parameterType = '0'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter







indicators parameter codedType = requestService 1 = request, essentialService 2 = no informationService 3 = no informationand without the User-to-user parameter,


Service = Service1Preferred = required request

and without the User-user information element.ISDN Parameter

values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = FalseUser-user information element not present




ETSI







indicators parameter codedType = requestService 1 = request, essentialService 2 = no informationService 3 = no informationand with the User-to-user parameter,


Service = Service1Preferred = required request

and with the User-user information element.ISDN Parameter

values:SETUP;Facility information elementUserUserService invoke componentService = 1Preferred = FalseUser-user information element


IAM;User-to-user indicators parameterType = '0'BService 1 = '11'BService 2 = '00'BService 3 = '00'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested), not having sent the ACM

message, on receipt of an ALERTING message with a Facility information elementcontaining a UserUserService return result component and without a User-userinformation element,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:ALERTING;Facility information elementUserUserService return result componentUser-user information element not present


ACM;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter not present


ETSI







message, on receipt of an ALERTING message with a Facility information elementcontaining a UserUserService return result component and with a User-userinformation element,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:ALERTING;Facility information elementUserUserService return result componentUser-user information element


ACM;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested), on receipt of an ALERTING

message with a Facility information element containing a UserUserService return resultcomponent and without a User-user information element,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:ALERTING;Facility information elementUserUserService return result componentUser-user information element not present


CPG;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter not present


ETSI







message with a Facility information element containing a UserUserService return resultcomponent and with a User-user information element,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:ALERTING;Facility information elementUserUserService return result componentUser-user information element


CPG;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter







message, on receipt of a CONNECT message with a Facility information elementcontaining a UserUserService return result component and without a User-userinformation element,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:CONNECT;Facility information elementUserUserService return result componentUser-user information element not present


CON;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter not present


ETSI







message, on receipt of a CONNECT message with a Facility information elementcontaining a UserUserService return result component and with a User-userinformation element,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:CONNECT;Facility information elementUserUserService return result componentUser-user information element


CON;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested), on receipt of a CONNECT


sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:CONNECT;Facility information elementUserUserService return result componentUser-user information element not present


ANM;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter not present


ETSI








sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:CONNECT;Facility information elementUserUserService return result componentUser-user information element


ANM;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested), on receipt of a DISCONNECT


sends a REL message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:DISCONNECT;Facility information elementUserUserService return result componentUser-user information element not present


REL;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter not present


ETSI








sends a REL message with the User-to-user indicators parameter codedType = responseService 1 = providedService 2 = no informationService 3 = no information


values:DISCONNECT;Facility information elementUserUserService return result componentUser-user information element


REL;User-to-user indicators parameterType = '1'BService 1 = '10'BService 2 = '00'BService 3 = '00'BUser-to-user parameter






criteria:Test purpose: Ensure that the SUT in state N7 (UUS1 has been activated), on receipt of a CONNECT

message with a User-user information element,sends an ANM message with the User-to-user parameter.











message with a User-user information element,sends a REL message with the User-to-user parameter.






ETSI


















COMPLETE message with a User-user information element,sends a REL message with the User-to-user parameter.











DISCONNECT message with a User-user information element,sends a REL message with the User-to-user parameter.

















ETSI







COMPLETE message with a User-user information element,sends a REL message with the User-to-user parameter.












sends a DISCONNECT message with a User-user information element.ISDN Parameter

values:DISCONNECT;User-user information element










sends a RELEASE message with a User-user information element.ISDN Parameter

values:RELEASE;User-user information element















ETSI







message with a Cause information element codedCause value = 29, Facility rejectedand a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByUser,

sends a REL message with the Cause parameter codedCause value = 29, Facility rejectedDiagnostics = User-to-user indicators parameter name.


DISCONNECT;Cause information elementCause value = '0011101'BFacility information elementUserUserService return error componentError value = 2


REL;Cause parameterCause value = '0011101'BDiagnostics = '00101010'B







Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested), on receipt of a DISCONNECTmessage with a Cause information element codedCause value = 29, Facility rejectedand a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,







ETSI






criteria:Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested), on receipt of a RELEASE

COMPLETE message with a Cause information element codedCause value = 29, Facility rejectedand a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByUser,



RELEASE COMPLETE;Cause information elementCause value = '0011101'BFacility information elementUserUserService return error componentError value = 2









Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested), on receipt of a RELEASECOMPLETE message with a Cause information element codedCause value = 29, Facility rejectedand a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,







ETSI







message with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByUser,

sends a REL message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.


DISCONNECT;Cause information elementCause value = PIXITFacility information elementUserUserService return error componentError value = 2


REL;User-to-user indicators parameterType = '1'BService 1 = '01'BService 2 = '00'BService 3 = '00'B







Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested), on receipt of a DISCONNECTmessage with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,







ETSI










RELEASE;Cause information elementCause value = PIXITFacility information elementUserUserService return error componentError value = 2









Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested), on receipt of a RELEASEmessage with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,







ETSI







COMPLETE message with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByUser,



RELEASE COMPLETE;Cause information elementCause value = PIXITFacility information elementUserUserService return error componentError value = 2









Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested), on receipt of a RELEASECOMPLETE message with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,







ETSI






criteria:Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested as “preferred"), not having sent

the ACM message, on receipt of an ALERTING message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByUser,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.


ALERTING;Facility information elementUserUserService return result componentError value = 2


ACM;User-to-user indicators parameterType = '1'BService 1 = '01'BService 2 = '00'BService 3 = '00'B







Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested as “preferred"), not having sentthe ACM message, on receipt of an ALERTING message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByNetwork,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.






ETSI







an ALERTING message with a Facility information element containing aUserUserService return error component codedError value = rejectedByUser,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.




CPG;User-to-user indicators parameterType = '1'BService 1 = '01'BService 2 = '00'BService 3 = '00'B







Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested as “preferred"), on receipt ofan ALERTING message with a Facility information element containing aUserUserService return error component codedError value = rejectedByNetwork,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.






ETSI







the ACM message, on receipt of a CONNECT message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByUser,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.


CONNECT;Facility information elementUserUserService return result componentError value = 2


CON;User-to-user indicators parameterType = '1'BService 1 = '01'BService 2 = '00'BService 3 = '00'B







Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested as “preferred"), not having sentthe ACM message, on receipt of a CONNECT message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByNetwork,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.






ETSI







CONNECT message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByUser,

sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.




ANM;User-to-user indicators parameterType = '1'BService 1 = '01'BService 2 = '00'BService 3 = '00'B







Test purpose: Ensure that the SUT in state N9 (UUS1 has been requested as “preferred"), on receipt of aCONNECT message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByNetwork,

sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = not providedService 2 = no informationService 3 = no information.






ETSI







ALERTING message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByUser,

sends a REL message with the Cause parameter codedCause value = 69, Requested facility not implementedDiagnostics = User-to-user indicators parameter name.





Comments: ISDN ALERTING -> SUT -> REL ISUP






Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested as “required"), on receipt of anALERTING message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByNetwork,







ETSI







ALERTING message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByUser,



















ETSI













Comments: ISDN CONNECT -> SUT -> REL ISUP






Test purpose: Ensure that the SUT in state N6 (UUS1 has been requested as “required"), on receipt of aCONNECT message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByNetwork,







ETSI


























ETSI


6.3.2.12.3 Service 2 (UUS2)




TSS reference: ISUP-DSS1/SS/UUS/UUS2ISDN selection



indicators parameter codedType = requestService 1 = no informationService 2 = request, not essentialService 3 = no information,


Service = Service2Preferred = preferred request.




IAM;User-to-user indicators parameterType = '0'BService 1 = '00'BService 2 = '10'BService 3 = '00'B







indicators parameter codedType = requestService 1 = no informationService 2 = request, essentialService 3 = no information,


Service = Service2Preferred = required request.


SETUP;Facility information elementUserUserService invoke componentService = 2Preferred = FalseUser-user information element not present




ETSI







message, on receipt of an ALERTING message with a Facility information elementcontaining a UserUserService return result component,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = providedService 3 = no information.











message with a Facility information element containing a UserUserService return resultcomponent,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = providedService 3 = no information.






ETSI



































ETSI




















sends a REL message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = not providedService 3 = no information.






ETSI


























ETSI







COMPLETE message with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,












the ACM message, on receipt of an ALERTING message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByUser,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = not providedService 3 = no information.






ETSI







Test purpose: Ensure that the SUT in state N6 (UUS2 has been requested as “preferred"), not having sentthe ACM message, on receipt of an ALERTING message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByNetwork,

sends an ACM message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = not providedService 3 = no information.











an ALERTING message with a Facility information element containing aUserUserService return error component codedError value = rejectedByUser,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = not providedService 3 = no information.






ETSI







Test purpose: Ensure that the SUT in state N9 (UUS2 has been requested as “preferred"), on receipt ofan ALERTING message with a Facility information element containing aUserUserService return error component codedError value = rejectedByNetwork,

sends a CPG message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = not providedService 3 = no information.











Test purpose: Ensure that the SUT in state N6 (UUS2 has been requested as “required"), on receipt of anALERTING message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByUser,







ETSI




















sends a REL message with the Cause parameter codedCause value = 88, Destination incompatibleDiagnostics = User-to-user indicators parameter name.






ETSI


























ETSI








sends a REL message with the Cause parameter codedCause value = 88, Destination incompatibleDiagnostics = User-to-user indicators parameter name.






6.3.2.12.4 Service 3 (UUS3)







indicators parameter codedType = requestService 1 = no informationService 2 = no informationService 3 = request, not essential,


Service = Service3Preferred = preferred request.




IAM;User-to-user indicators parameterType = '0'BService 1 = '00'BService 2 = '00'BService 3 = '10'B


ETSI







indicators parameter codedType = requestService 1 = no informationService 2 = no informationService 3 = request, essential,


Service = Service3Preferred = required request.


SETUP;Facility information elementUserUserService invoke componentService = 3Preferred = FalseUser-user information element not present









message, on receipt of a CONNECT message with a Facility information elementcontaining a UserUserService return result component,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = provided.





Comments: ISDN CONNECT-> SUT -> ACM ISUP

ETSI







message with a Facility information element containing a UserUserService return resultcomponent,

sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = provided.





Comments: ISDN CONNECT-> SUT -> ANM ISUP





criteria:Test purpose: Ensure that the SUT in the state N10, on receipt of a FAR message with the User-to-user

indicators parameter codedType = requestService 3 = request, not essential,

sends a FACILITY message with a Facility information element containing aUserUserService invoke component coded

Service 1 = no informationService 2 = no informationService = Service 3Preferred = preferred request.




FAR;User-to-user indicators parameterType = '0'BService 1 = '00'BService 2 = '00'BService 3 = '10'B

Comments: ISUP FAR -> SUT -> ISDN FACILITY

ETSI






criteria:Test purpose: Ensure that the SUT in the state N10 (UUS3 has been requested), on receipt of a

FACILITY message with a Facility information element containing a UserUserServicereturn result component,

sends a FAA message with the User-to-user indicators parameter codedType = responseService 3 = provided.




FAA;User-to-user indicators parameterType = '1'BService 3 = '10'B

Comments: ISDN FACILITY -> SUT -> IAM FAA





criteria:Test purpose: Ensure that the SUT in the state N10, on receipt of a FACILITY message with a Facility


sends a FAR message with the User-to-user indicators parameter codedType = requestService 3 = request, not essential.




FAR;User-to-user indicators parameterType = '0'BService 3 = '10'B

Comments: ISDN FACILITY -> SUT -> ISUP FAR

ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FAA

message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = provided,

sends a FACILITY message with a Facility information element containing aUserUserService return result component.




FAA;User-to-user indicators parameterType = '1'BService 1 = '00'BService 2 = '00'BService 3 = '10'B

Comments: ISUP FAA -> SUT -> FACILITY ISDN























ETSI

























ETSI








sends a REL message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = not provided.


















ETSI


























ETSI



















COMPLETE message with a Cause information element codedCause value = other than 29and a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,







ETSI







the ACM message, on receipt of a CONNECT message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByUser,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = not provided.











Test purpose: Ensure that the SUT in state N6 (UUS3 has been requested as “preferred"), not having sentthe ACM message, on receipt of a CONNECT message with a Facility informationelement containing a UserUserService return error component codedError value = rejectedByNetwork,

sends a CON message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = not provided.






ETSI








sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = not provided.











Test purpose: Ensure that the SUT in state N7 (UUS3 has been requested as “preferred"), on receipt of aCONNECT message with a Facility information element containing a UserUserServicereturn error component codedError value = rejectedByNetwork,

sends an ANM message with the User-to-user indicators parameter codedType = responseService 1 = no informationService 2 = no informationService 3 = not provided.






ETSI


























ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FACILITY

message with a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByUser,













Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FACILITYmessage with a Facility information element containing a UserUserService return errorcomponent codedError value = rejectedByNetwork,








ETSI






criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on the expiry of timer T1,


and with a Cause parameter codedCause value = 69, Requested facility not implemented.










criteria:Test purpose: Ensure that the SUT in state N10 (UUS3 has been requested), on receipt of a FRJ

message with the User-to-user indicators parameter codedType = responseService 3 = not provided,

sends a FACILITY message with a Facility information element containing aUserUserService return error component coded


values:FACILITY;Facility information elementUserUserService return error componentError value = 2


FRJ;User-to-user indicators parameterType = '1'BService 3 = '01'B

Comments: ISUP FRJ -> SUT -> FACILITY ISDN

ETSI


6.3.2.13 Completion of Call to Busy Subscriber (CCBS)

ISDN selection criteria: CCBS available.





TSS reference: ISUP-DSS1/SS/CCBS/S T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N9, on receipt of a DISCONNECT message with the Cause

information element codedCause value = ISDN_CV,

sends a REL message with the Cause parameter codedCause value = ISUP_CVDiagnostics = CCBS possible.


DISCONNECT;Cause information elementCause value = ISDN_CV



Comments: ISDN DISCONNECT-> SUT -> ISUP REL





criteria:Test purpose: Ensure that the SUT in state N9, on receipt of a RELEASE message with the Cause

information element codedCause value = ISDN_CV,



RELEASE;Cause information elementCause value = ISDN_CV



Comments: ISDN RELEASE-> SUT -> ISUP REL

ETSI






criteria:Test purpose: Ensure that the SUT in state N6, on receipt of a RELEASE COMPLETE message with the

Cause information element codedCause value = ISDN_CV,



RELEASE COMPLETE;Cause information elementCause value = ISDN_CV



Comments: ISDN RELEASE COMPLETE-> SUT -> ISUP REL







criteria:Test purpose: Ensure that the SUT in the Idle state (Remote user free indication has been delivered), on

receipt of an IAM message with the CCBS parameter codedCCBS call indicator = CCBS call,

sends a SETUP message.ISDN Parameter

values:SETUP;




ETSI






TSS reference: ISUP-DSS1/SS/CCBS/T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N9, on receipt of a DISCONNECT message with the Cause

information element codedCause value = ISDN_CVand with a Facility information element containing a CCBS-T-Available invokecomponent,



DISCONNECT;Cause information elementCause value = ISDN_CVFacility information elementCCBS-T-Available invoke component



Comments: ISDN DISCONNECT-> SUT -> ISUP REL





criteria:Test purpose: Ensure that the SUT in state N9, on receipt of a RELEASE message with the Cause

information element codedCause value = ISDN_CVand with a Facility information element containing a CCBS-T-Available invokecomponent,



RELEASE;Cause information elementCause value = ISDN_CVFacility information elementCCBS-T-Available invoke component



Comments: ISDN RELEASE-> SUT -> ISUP REL

ETSI






criteria:Test purpose: Ensure that the SUT in state N6, on receipt of a RELEASE COMPLETE message with the

Cause information element codedCause value = ISDN_CVand with a Facility information element containing a CCBS-T-Available invokecomponent,



RELEASE COMPLETE;Cause information elementCause value = ISDN_CVFacility information elementCCBS-T-Available invoke component



Comments: ISDN RELEASE COMPLETE-> SUT -> ISUP REL








receipt of an IAM message with the CCBS parameter codedCCBS call indicator = CCBS call,

sends a SETUP message with a Facility information element containing a CCBS-T-Callinvoke component.






ETSI


6.3.2.14 Explicit Call Transfer (ECT)




ISUP reference:EN 300 899-1 [1], clause 3.1.2.18.1.1.1

TSS reference: ISUP-DSS1/SS/ECT/S T reference pointISDN selection



activation parameter codedFeature code = call transferand the Generic notification parameter codedNotification indicator = Call transfer, alerting,

sends a FACILITY message with the Notification indicator information elementcoded

Notification description = Call transfer, alertingand with the Facility information element containing a RequestSubaddress invoke

component.ISDN Parameter

values:FACILITY;Notification indicator information elementNotification description = '1101001'BFacility information elementComponent = RequestSubaddress invoke component







criteria:Interaction ECT-ECT supported


Test purpose: Ensure that the SUT in state N7, on receipt of a FAC message with the Service activationparameter codedFeature code = call transferand the Generic notification parameter codedNotification indicator = Call transfer, alerting,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Call transfer, alerting.


NOTIFYY;Notification indicator information elementNotification description = '1101001'B



Comments: ISUP FAC -> SUT -> NOTIFY ISDN

ETSI






criteria:Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,

on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Connected subaddress informationelement,


Notification description = Call transfer, active,the Redirection number information element coded

Presentation indicator = Presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planNumber digits included

and with the Facility information element containing a SubaddressTransfer invokecomponent.


FACILITY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BNumber digits = PIXITFacility information elementComponent = SubaddressTransfer invoke component


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Connected subaddress information element


ETSI







on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,








FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component


ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has been sent,on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Connected subaddress informationelement,








FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Connected subaddress information element


ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has been sent,on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,








FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component


Values for the test purposes TP614003 - TP614006VA_01 ISDN_TON = national number, '010'B ISUP_NAI = national number, '0000011'BVA_02 ISDN_TON = international number, '001'B ISUP_NAI = international number, '0000100'BVA_03 ISDN_TON = subscriber number, '100'B ISUP_NAI = subscriber number, '0000001'BVA_04 ISDN_TON = unknown, '000'B ISUP_NAI = unknown, '0000010'B

ETSI







on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter and without any subaddress information included,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Call transfer, active

and the Redirection number information element codedPresentation indicator = Number not available due to interworkingType of number = unknownNumbering plan identification = unknownNumber digits not included.


NOTIFY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '10'BType of number = '000'BNumbering plan identification = '0000'BNumber digits not included


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterSubaddress information not included


ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has been sent,on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter and without any subaddress information included,








ETSI







on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,






FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameter not present


ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has been sent,on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,








ETSI







on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand with the Call transfer number parameter codedAddress presentation restricted indicator = presentation restricted,


and the Redirection number information element codedPresentation indicator = Presentation restrictedType of number = unknownNumbering plan identification = unknownNumber digits not included.




FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted indicator = '01'B


ETSI







Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand with the Call transfer number parameter codedAddress presentation restricted indicator = presentation restricted,








ETSI






criteria:Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has not been

sent, on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals included,




and with the Facility information element containing a RequestSubaddress invokecomponent.


FACILITY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BNumber digits = PIXITFacility information elementComponent = RequestSubaddress invoke component


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXIT


ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has not beensent, on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals included,


and the Redirection number information element codedPresentation indicator = Presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planNumber digits included.


NOTIFY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BNumber digits = PIXIT


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXIT



ETSI







sent, on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,



Presentation indicator = Number not available due to interworkingType of number = unknownNumbering plan identification = unknownNumber digits not included



FACILITY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '10'BType of number = '000'BNumbering plan identification = '0000'BNumber digits not includedFacility information elementComponent = RequestSubaddress invoke component




ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has not beensent, on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,








ETSI







sent, on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand the Call transfer number parameter codedAddress presentation restricted parameter = presentation restricted,



Presentation indicator = Presentation restrictedType of number = unknownNumbering plan identification = unknownNumber digits not included



FACILITY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '01'BType of number = '000'BNumbering plan identification = '0000'BNumber digits not includedFacility information elementComponent = RequestSubaddress invoke component


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '01'B


ETSI







Test purpose: Ensure that the SUT in state N7, when a “call transfer, alerting" notification has not beensent, on receipt of a FAC message with the Service activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand the Call transfer number parameter codedAddress presentation restricted parameter = presentation restricted,






FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '01'B







activation parameter codedFeature code = call transfer,without the Generic notification parameterand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,



FACILITY;Facility information elementComponent = SubaddressTransfer invoke component


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameter not presentAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component


ETSI






criteria:Test purpose: Ensure that the SUT in state N7, on receipt of a FAC message with the Service activation

parameter codedFeature code = call transfer,without the Generic notification parameterand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,





FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameter not presentAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component


ETSI







Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Connected subaddress informationelement,








CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Connected subaddress information element

Comments: ISUP CPG -> SUT -> FACILITY ISDN

ETSI







Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,








CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component


ETSI







on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Connected subaddress informationelement,








CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Connected subaddress information element


ETSI







on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals includedand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,








CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXITAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component



ETSI







Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter and without any subaddress information included,






CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterSubaddress information not included







on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter and without any subaddress information included,








ETSI







Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,






CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameter not present







on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,








ETSI







Test purpose: Ensure that the SUT in state N10, when a “call transfer, alerting" notification has been sent,on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand with the Call transfer number parameter codedAddress presentation restricted indicator = presentation restricted,






CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted indicator = '01'B







on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand with the Call transfer number parameter codedAddress presentation restricted indicator = presentation restricted,








ETSI







sent, on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedNature of address indicator = ISUP_NAINumbering plan indicator = ISDN (Telephony) numbering planAddress signals included,


and the Redirection number information element codedPresentation indicator = Presentation allowedType of number = ISDN_TON or unknownNumbering plan identification = ISDN/Telephony numbering planNumber digits included.


NOTIFY;Notification indicator information elementNotification description = '1101010'BRedirection number information elementPresentation indicator = '00'BType of number = ISDN_TON or '000'BNumbering plan identification = '0001'BNumber digits = PIXIT


CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BNature of address indicator = ISUP_NAINumbering plan indicator = '001'BAddress signals = PIXIT


Values for the test purposes TP614031VA_01 ISDN_TON = national number, '010'B ISUP_NAI = national number, '0000011'BVA_02 ISDN_TON = international number, '001'B ISUP_NAI = international number, '0000100'BVA_03 ISDN_TON = subscriber number, '100'B ISUP_NAI = subscriber number, '0000001'BVA_04 ISDN_TON = unknown, '000'B ISUP_NAI = unknown, '0000010'B

ETSI







sent, on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,













sent, on receipt of a CPG message with the Generic notification parameter codedNotification indicator = Call transfer, activeand the Call transfer number parameter codedAddress presentation restricted parameter = presentation restricted,






CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '01'B


ETSI







notification parameter codedNotification indicator = Call transfer, alerting,

sends a NOTIFY message with the Notification indicator information element codedNotification description = Call transfer, alerting.




CPG;Generic notification parameterNotification indicator = '1101001'B






criteria:Test purpose: Ensure that the SUT in state N10, having sent a RequestSubaddress invoke component, on

receipt of a FACILITY message with the Facility information element containing aSubaddressTransfer invoke component,

sends a FAC message with the Service activation parameter codedFeature code = call transfer

and with the Access transport parameter including a Facility information element witha SubaddressTransfer invoke component.






ETSI








TSS reference: ISUP-DSS1/SS/ECT/T reference point/Loop preventionISDN selection


criteria:Test purpose: Ensure that the SUT in state N10, on receipt of a LOP message with the Loop prevention

indicators parameter codedType = requestand with the Call transfer reference parameter,

sends a FACILITY message with the Facility information element containing anEctLoopTest invoke component.


FACILITY;Facility information elementComponent = EctLoopTest invoke component


LOP;Loop prevention indicators parameterType = '0'BCall transfer reference parameter

Comments: ISUP LOP -> SUT -> FACILITY ISDN





criteria:Test purpose: Ensure that the SUT in state N10, having requested the procedure to avoid looping of

uncontrolled circuits, on receipt of a FACILITY message with the Facility informationelement containing an EctLoopTest return result component codedLoopResult = ISDN_LR,

sends a LOP message with the Loop prevention indicators parameter codedType = responseResponse indicator = ISUP_RI

and with the Call transfer reference parameter.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctLoopTest return result componentLoopResult = ISDN_LR


LOP;Loop prevention indicators parameterType = '1'BResponse indicator = ISUP_RICall transfer reference parameter


Values for the test purpose TP614202VA_01 ISUP_LR = insufficient information, 0 ISUP_RI = insufficient information, '00'BVA_02 ISUP_LR = no loop exists, 1 ISUP_RI = no loop exists, '01'BVA_03 ISUP_LR = simultaneous transfer, 2 ISUP_RI = simultaneous transfer, '10'B

ETSI







uncontrolled circuits, on receipt of a FACILITY message with the Facility informationelement containing an EctLoopTest return error component codedError value = notAvailable,

sends a LOP message with the Loop prevention indicators parameter codedType = responseResponse indicator = insufficient information

and with the Call transfer reference parameter.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctLoopTest return error componentError value = 3


LOP;Loop prevention indicators parameterType = '1'BResponse indicator = '00'BCall transfer reference parameter







uncontrolled circuits, on receipt of a FACILITY message with the Facility informationelement containing an EctLoopTest reject component,


values:FACILITY;Facility information elementComponent = EctLoopTest reject component


-

Comments: ISDN FACILITY -> SUT -> -

ETSI





TSS reference: ISUP-DSS1/SS/ECT/S T reference point/Service invocationISDN selection



activation parameter codedFeature code = call transferand the Generic notification parameter codedNotification indicator = Call transfer, alerting,

sends a FACILITY message with the Facility information element containing anEctInform invoke component coded

Argument value = alerting.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 0









activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedand with the Access transport parameter including a Connected subaddress informationelement,

sends a FACILITY message with a Facility information element containing anEctInform invoke component coded

Argument value = activeRedirection number included

and with a Facility information element containing a SubaddressTransfer invokecomponent.


FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 1Redirection number includedFacility information elementComponent = SubaddressTransfer invoke component


FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BAccess transport parameter including a Connected subaddress information element


ETSI







activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,







FAC;Service activation parameterFeature code = '00000001'BGeneric notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component


ETSI







activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter and without any subaddress information included,


Argument value = activeRedirection number included.


FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 1Redirection number included









activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,








ETSI







activation parameter codedFeature code = call transfer,the Generic notification parameter codedNotification indicator = Call transfer, activeand with the Call transfer number parameter codedAddress presentation restricted indicator = presentation restricted,













activation parameter codedFeature code = call transferand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,







ETSI







notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedand with the Access transport parameter including a Connected subaddress informationelement,







CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BAccess transport parameter including a Connected subaddress information element


ETSI







notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter codedAddress presentation restricted parameter = presentation allowedand with the Access transport parameter including a Facility information element with aSubaddressTransfer invoke component,







CPG;Generic notification parameterNotification indicator = '1101010'BCall transfer number parameterAddress presentation restricted parameter = '00'BAccess transport parameter including a Facility information element with aSubaddressTransfer invoke component







notification parameter codedNotification indicator = Call transfer, active,the Call transfer number parameter and without any subaddress information included,








ETSI







notification parameter codedNotification indicator = Call transfer, activeand without the Call transfer number parameter,













notification parameter codedNotification indicator = Call transfer, activeand with the Call transfer number parameter codedAddress presentation restricted indicator = presentation restricted,








ETSI







notification parameter codedNotification indicator = Call transfer, alerting,


Argument value = alerting.ISDN Parameter

values:FACILITY;Facility information elementComponent = EctInform invoke componentArgument value = 0


CPG;Generic notification parameterNotification indicator = '1101001'B







information element containing a SubaddressTransfer invoke component,sends a FAC message with the Service activation parameter coded

Feature code = call transferand with the Access transport parameter including a Facility information element with

a SubaddressTransfer invoke component.ISDN Parameter

values:FACILITY;Facility information elementComponent = SubaddressTransfer invoke component




ETSI


6.3.2.15 Completion of Calls on No reply (CCNR)

ISDN selection criteria: CCNR available.





TSS reference: ISUP-DSS1/SS/CCNR/S T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of an

ALERTING message,sends an ACM message with the Backward call indicators parameter coded

Called party's status indicator = subscriber freeand with the CCNR possible indicator parameter coded

CCNR possible indicator = CCNR possible.ISDN Parameter

values:ALERTING;



Comments: ISDN ALERTING -> SUT -> ISUP ACM





criteria:Test purpose: Ensure that the SUT in state N9, on receipt of an ALERTING message,

sends a CPG message with the Event information parameter codedEvent indicator = ALERTING

and with the CCNR possible indicator parameter codedCCNR possible indicator = CCNR possible.


ALERTING;



Comments: ISDN ALERTING -> SUT -> ISUP CPG

ETSI







receipt of an IAM message with the CCSS parameter codedCCSS call indicator = CCSS call,

sends a SETUP message.ISDN Parameter

values:SETUP;








TSS reference: ISUP-DSS1/SS/CCNR/T reference pointISDN selection


criteria:Test purpose: Ensure that the SUT in state N6, not having sent the ACM message, on receipt of an

ALERTING message with a Facility information element containing a CCBS-T-Availableinvoke component,

sends an ACM message with the Backward call indicators parameter codedCalled party's status indicator = subscriber free

and with the CCNR possible indicator parameter codedCCNR possible indicator = CCNR possible.





Comments: ISDN ALERTING -> SUT -> ISUP ACM

ETSI






criteria:Test purpose: Ensure that the SUT in state N9, on receipt of an ALERTING message with a Facility

information element containing a CCBS-T-Available invoke component,sends a CPG message with the Event information parameter coded

Event indicator = ALERTINGand with the CCNR possible indicator parameter coded

CCNR possible indicator = CCNR possible.ISDN Parameter

values:ALERTING;Facility information elementCCBS-T-Available invoke component



Comments: ISDN ALERTING -> SUT -> ISUP CPG






receipt of an IAM message with the CCSS parameter codedCCSS call indicator = CCSS call,

sends a SETUP message with a Facility information element containing a CCBS-T-Callinvoke component.






ETSI


7 Test coverage

7.1 General remarksThe test purposes defined in the present document cover most main capabilities of the ISUP '97 reference specification.A list of areas/capabilities currently not covered is provided in table 1. The test purposes defined are not exhaustive, anddo not cover all aspects of the reference specification. As can be seen from table 2, the majority of test purposes (60 %)concentrate on valid behaviour.

The number of invalid behaviour test purposes is limited. An expansion of the invalid behaviour test purposes is left forfurther study.

Table 1: Issues not tested

Table 2: Test coverage

Number of Test Purposes Interworking DSS1/ISUP '92 Basic Call

Number of test cases for interworking from DSS1 to ISUP(outgoing call) test purposes

Number of test cases for interworking from Non-ISDN access to ISUP(outgoing call)Number of test cases for interworking from ISUP to DSS1 (incoming call)Number of test cases for interworking from ISUP to Non-ISDN access(incoming call)Total

ETSI


Annex A (informative):Definition of causes valuesThe following tables indicate the usage of cause values and location codes within the present document. For moreprecise usage of the location codes in the cause information element, see EN 300 485 [7].

Table A.1: DSS1/ISUP Receipt of the Release message (State 2 and State 3)

Cause Definition LocationDSS1 ISUP DSS1 ISUP

1 1 Unallocated (unassigned) number U, RPN,RLN, TN,

INTL

U, RPN,RLN, TN,

INTL2 2 No route to specified transit network LN, TN LN, TN3 3 No route to destination U, RPN, LN U, RPN, LN17 17 User busy U, RPN, RLN U, RPN, RLN18 18 No user responding RPN, RLN RPN, RLN21 21 Call rejected U, RPN, RLN U, RPN, RLN22 22 Number changed U, RPN, RLN U, RPN, RLN27 27 Destination out of order RLN RLN28 28 Invalid number format (address incomplete) U, RPN,

RLN, LN,INTL

U, RPN,RLN, LN;

INTL29 29 Facility rejected U, RPN,

RLN, LN,TN, INTL

U, RPN,RLN, LN,TN, INTL

31 31 Normal, unspecified RLN, TN,INTL

RLN, TN,INTL

34 34 No circuit/channel available U, RPN,RLN, LN,TN, INTL

U, RPN,RLN, LN,TN, INTL

38 38 Network out of order U, RPN U, RPN41 41 Temporary failure U, RPN,

RLN, LNU, RPN,RLN, LN

42 42 Switching equipment congestion TN, RLN,INTL

TN, RLN,INTL

43 43 Access information discarded U, RPN, LN U, RPN, LN44 44 Requested circuit/channel not available U, RPN, LN U, RPN, LN47 47 Resource unavailable, unspecified U, RPN U, RPN

ETSI



55 55 Incoming calls barred within CUG RLN RLN, LN57 57 Bearer capability not authorized RPN, RLN RPN, RLN,

LN58 58 Bearer capability not presently available RPN, RLN RPN, RLN,

LN63 63 Service or option not available, unspecified RPN, RLN,

LNRPN, RLN,

LN65 65 Bearer capability not implemented RPN, RLN,

LN, TN, INTLRPN, RLN,

LN, TN, INTL69 69 Requested facility not implemented U, RPN,

RLN, LNU, RPN,RLN; LN

70 70 Only restricted digital information bearercapability is available

U, RPN, RLN U, RPN, RLN

87 87 User not member of CUG RLN RLN88 88 Incompatible destination U, RPN, LN U, RPN, LN90 90 Non-existent CUG U, RPN,


91 91 Invalid transit network selection TN TN95 95 Invalid message, unspecified U, RPN, LN U, RPN, LN97 97 Message type non-existent or not implemented U, RPN, LN U, RPN, LN99 99 Information element/parameter non-existent or

not implementedU, RPN, LN U, RPN, LN

111 110 Message with unrecognized parameter,discarded

RLN, TN,INTL

RLN, TN,INTL

111 111 Protocol error, unspecified RLN RLN

Table A.2: DSS1/ISUP Receipt of the Release message (State 4)


19 19 No answer from user (user alerted) RLN, LN,TN, INTL

RLN, TN,TN, INTL

27 27 Destination out of order RLN RLN31 31 Normal, unspecified RLN, TN,

INTLRLN, TN,

INTL38 38 Network out of order RPN RPN41 41 Temporary failure U, RPN,


42 42 Switching congestion TN, RLN TN, RLN47 47 Resource unavailable, unspecified U, RPN U, RPN

102 102 Recovery on timer expiry RLN RLN,111 111 Protocol error, unspecified RLN, TN,

INTLRLN, TN,

INTL

Table A.3: DSS1/ISUP Receipt of the Release message (State 10)


16 16 Normal call clearing U, RPN U, RPN27 27 Destination out of order RLN RLN31 31 Normal, unspecified RLN, TN,

INTLRLN, TN,

INTL38 38 Network out of order U, RPN U, RPN41 41 Temporary failure U, RPN,


42 42 Switching equipment congestion RPN, RLN,LN, TN, INTL

RPN, RLN,LN, TN, INTL

47 47 Resource unavailable, unspecified U, RPN U, RPN111 111 Protocol error, unspecified RLN, TN,

INTLRLN, TN,

INTL

ETSI


Table A.4: DSS1/ISUP - Sending of the Release message (State 2)


no 31 or 111 --- RLN, LN1 31 Unallocated (unassigned) number any RLN, LN,2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an

established channelany RLN, LN

8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 16 Normal call clearing U, RPN U, RPN17 31 User busy any RLN, LN18 31 No user responding any RLN, LN19 31 No answer from user (user alerted) any RLN, LN20 31 Subscriber absent any RLN, LN21 31 Call rejected any RLN, LN22 31 Number changed any RLN, LN26 31 Non-selected user clearing any RLN, LN27 31 Destination out of order any RLN, LN28 31 Invalid number format (address incomplete) any RLN, LN29 29 Facility rejected any RLN, LN30 31 Response to STATUS ENQUIRY any RLN, LN31 31 Normal, unspecified U, RPN U, RPN34 31 No circuit/channel available any RLN, LN38 38 Network out of order RPN RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure RPN RPN42 31 Switching equipment congestion any RLN, LN43 31 Access information discarded any RLN, LN44 31 Requested circuit/channel not available any RLN, LN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified any RLN, LN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN62 31 Inconsistency in designated outgoing access

information and subscriber classany RLN, LN

ETSI



63 31 Service or option not available, unspecified any RLN, LN65 31 Bearer capability not implemented any RLN, LN66 31 Channel type not implemented any RLN, LN69 31 Requested facility not implemented any RLN, LN70 31 Only restricted digital information bearer

capability is availableany RLN, LN

79 31 Service or option not implemented, unspecified any RLN, LN81 95 Invalid call reference value any RLN, LN82 31 Identified channel does not exist any RLN, LN83 31 A suspended call exists, but this call identity

does notany RLN, LN

84 31 Call identity in use any RLN, LN85 31 No call suspended any RLN, LN86 31 Call having the requested call identity has been

clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 31 Incompatible destination any RLN, LN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified any RLN, LN96 31 Mandatory information element is missing any RLN, LN97 31 Message type non-existent or not implemented any RLN, LN98 31 Message not compatible with call state or

message type non-existent or not implementedany RLN, LN

99 31 Information element/parameter non-existent ornot implemented

any RLN, LN

100 111 Invalid information element contents any RLN, LN101 111 Message not compatible with call state any RLN, LN102 102 Recovery on timer expiry U, RPN U; RPN103 31 Parameter non-existent or not implemented,

passed onany RLN, LN


any RLN, LN

111 111 Protocol error, unspecified U, RPN U; RPN127 31 Interworking, unspecified any RLN, LN

ETSI




no 31 or 111 RLN, LN1 31 Unallocated (unassigned) number any RLN, LN2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 16 Normal call clearing U, RPN U, RPN, RLN17 31 User busy any RLN, LN18 31 No user responding any RLN, LN19 31 No answer from user (user alerted) any RLN, LN20 31 Subscriber absent any RLN, LN21 31 Call rejected any RLN, LN22 31 Number changed any RLN, LN26 31 Non-selected user clearing any RLN, LN27 31 Destination out of order any RLN, LN28 31 Invalid number format (address incomplete) any RLN, LN29 31 Facility rejected any RLN, LN30 31 Response to STATUS ENQUIRY any RLN, LN31 31 Normal, unspecified U, RPN U, RPN34 31 No circuit/channel available any RLN, LN38 38 Network out of order U, RPN U, RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure U, RPN U, RPN42 42 Switching equipment congestion U, RPN U, RPN43 31 Access information discarded any RLN, LN44 31 Requested circuit/channel not available any RLN, LN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified any RLN, LN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN

ETSI



62 31 Inconsistency in designated outgoing accessinformation and subscriber class

any RLN




does notany RLN, LN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 31 Incompatible destination any RLN, LN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified U, RPN U, RPN96 111 Mandatory information element is missing U, RPN RLN, LN97 97 Message type non-existent or not implemented U, RPN U, RPN98 111 Message not compatible with call state or



any RLN, LN

100 111 Invalid information element contents any RLN, LN101 111 Message not compatible with call state any RLN, LN102 102 Recovery on timer expiry U, RPN U, RPN103 31 Parameter non-existent or not implemented,



any RLN, LN

111 31 Protocol error, unspecified U, RPN U; RPN127 31 Interworking, unspecified any RLN, LN

ETSI




no 31 or 111 --- RLN, LN1 31 Unallocated (unassigned) number any RLN, LN2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 16 Normal call clearing U, RPN U, RPN17 31 User busy any RLN, LN18 31 No user responding any RLN, LN19 31 No answer from user (user alerted) any RLN, LN20 31 Subscriber absent any RLN, LN21 31 Call rejected any RLN, LN22 31 Number changed any RLN, LN26 31 Non-selected user clearing any RLN, LN27 31 Destination out of order any RLN, LN28 31 Invalid number format (address incomplete) any RLN, LN29 31 Facility rejected any RLN, LN30 31 Response to STATUS ENQUIRY any RLN, LN31 31 Normal, unspecified U, RPN U, LPN, RPN34 31 No circuit/channel available any RLN38 38 Network out of order U, RPN U, RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure U, RPN, U, RPN42 42 Switching equipment congestion RPN RLN, LN43 31 Access information discarded any RLN, LN44 31 Requested circuit/channel not available any RLN, LN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified any RLN, LN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN

ETSI



62 31 Inconsistency in designated outgoing accessinformation and subscriber class

any RLN, LN



79 31 Service or option not implemented, unspecified any RLN, LN81 95 Invalid call reference value U, RPN RLN, LN82 31 Identified channel does not exist any RLN, LN83 31 A suspended call exists, but this call identity

does notany RLN, LN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 31 Incompatible destination any RLN, LN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified U, RPN U; RPN96 111 Mandatory information element is missing any RLN, LN97 31 Message type non-existent or not implemented any RLN, LN98 111 Message not compatible with call state or

message type non-existent or not implementedany RLN


U, RPN U; RPN

100 111 Invalid information element contents U, RPN RLN, LN101 111 Message not compatible with call state U, RPN RLN, LN102 102 Recovery on timer expiry U, RPN U, RPN103 31 Parameter non-existent or not implemented,



any RLN, LN

111 111 Protocol error, unspecified U, RPN U, RPN127 31 Interworking, unspecified any RLN, LN

Table A.7: ISUP/DSS1 - Receipt of the Release message (States 6, 25, 7, 9, 10)


16 16 Normal call clearing U, RPN U, RPN,30 31 Response to STATUS ENQUIRY RLN, LN31 31 Normal, unspecified U, RPN U,RPN38 38 Network out of order U, LPN, RPN U, LPN, RPN41 41 Temporary failure U, LPN, RPN U, LPN, RPN95 95 Invalid message, unspecified RLN, LN RLN, LN

102 102 Recovery on timer expiry U, RPN U, RPN111 111 Protocol error, unspecified RLN, LN RLN, LN

ETSI


Table A.8: ISUP/DSS1 - Sending of the Release message (State 6)


no 31 or 111 --- RLN, LN1 1 Unallocated (unassigned) number RPN RPN2 31 No route to specified transit network any RLN, LN3 3 No route to destination RPN RPN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 ??? Channel unacceptable U, RPN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 31 Normal call clearing any RLN, LN17 17 User busy U, RPN U, RPN18 18 No user responding RPN RPN, LN19 31 No answer from user (user alerted) any RLN, LN20 31 Subscriber absent any RPN21 21 Call rejected U, RPN LPN, RPN22 22 Number changed RPN RPN, LN26 31 Non-selected user clearing any RLN, LN27 27 Destination out of order RPN RPN28 28 Invalid number format (address incomplete) U, RPN U, RPN29 29 Facility rejected U, LPN, RPN U, LPN, RPN30 31 Response to STATUS ENQUIRY U, RPN RLN, LN31 31 Normal, unspecified U, RPN U, RPN34 34 No circuit/channel available U, LPN, RPN U, LPN, RPN38 38 Network out of order RPN RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure RPN RPN42 42 Switching equipment congestion RPN RPN43 43 Access information discarded U, RPN U, RPN

ETSI



44 44 Requested circuit/channel not available U, RPN U, RPN46 31 Precedence call blocked any RLN47 47 Resource unavailable, unspecified U, RPN U, RPN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 57 Bearer capability not authorized RPN RPN, LN58 58 Bearer capability not presently available RPN RPN, LN62 31 Inconsistency in designated outgoing access

information and subscriber classany RLN

63 63 Service or option not available, unspecified RPN RPN65 65 Bearer capability not implemented RPN RPN66 31 Channel type not implemented any RLN, LN69 31 Requested facility not implemented U, RPN U, RPN70 70 Only restricted digital information bearer

capability is availableU, RPN U, RPN

79 79 Service or option not implemented, unspecified U, RPN U, RPN81 95 Invalid call reference value U, RPN RLN, LN82 95 Identified channel does not exist U, RPN RLN, LN83 31 A suspended call exists, but this call identity

does notany RLN, LN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 88 Incompatible destination U, RPN U, RPN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified U, RPN U, RPN96 111 Mandatory information element is missing U, RPN RLN, LN97 31 Message type non-existent or not implemented U, RPN U, RPN98 111 Message not compatible with call state or

message type non-existent or not implementedU, RPN RLN, LN


U, RPN U, RPN

100 111 Invalid information element contents U, RPN RLN, LN101 111 Message not compatible with call state U, RPN RLN, LN102 31 Recovery on timer expiry U, LPN, RPN U, LPN, RPN103 31 Parameter non-existent or not implemented,



any RLN, LN


ETSI




no 31 or 111 ---1 1 Unallocated (unassigned) number RPN RPN2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 31 Normal call clearing any RLN, LN17 17 User busy RPN RLN, LN18 18 No user responding RPN RPN, LN19 31 No answer from user (user alerted) any RLN, LN20 31 Subscriber absent any RLN, LN21 21 Call rejected U, RPN U, RPN22 31 Number changed RLN, LN26 31 Non-selected user clearing RLN, LN27 27 Destination out of order RPN RPN, LN28 28 Invalid number format (address incomplete) any RLN, LN29 29 Facility rejected U, RPN U, RPN30 111 Response to STATUS ENQUIRY U, RPN RLN, LN31 31 Normal, unspecified U, RPN U, RPN34 31 No circuit/channel available U RLN, LN38 38 Network out of order RPN RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure RPN RPN42 42 Switching equipment congestion RPN RPN43 31 Access information discarded any RLN, LN

ETSI



44 31 Requested circuit/channel not available U, RPN U, RPN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified any RLN, LN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN62 31 Inconsistency in designated outgoing access


63 31 Service or option not available, unspecified any RLN, LN65 65 Bearer capability not implemented U, RPN U, RPN66 31 Channel type not implemented any RLN, LN69 31 Requested facility not implemented U, RPN U, RPN70 31 Only restricted digital information bearer


79 31 Service or option not implemented, unspecified any RLN, LN81 31 Invalid call reference value any RLN, LN82 95 Identified channel does not exist U, RPN RLN, LN83 31 A suspended call exists, but this call identity

does notany RLN, LN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 31 Incompatible destination any RLN, LN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified U, RPN U, RPN96 31 Mandatory information element is missing any RLN, LN97 31 Message type non-existent or not implemented any RLN, LN98 111 Message not compatible with call state or

message type non-existent or not implementedU, RPN RLN, LN


U, RPN U, RPN

100 111 Invalid information element contents U, RPN RLN, LN101 111 Message not compatible with call state U, RPN RLN, LN102 102 Recovery on timer expiry U, RPN U, RPN103 31 Parameter non-existent or not implemented,



any RLN, LN


ETSI




no 31 or 111 ---1 31 Unallocated (unassigned) number any RLN, LN2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 31 Normal call clearing any RLN, LN17 31 User busy any RLN, LN18 31 No user responding any RLN, LN19 31 No answer from user (user alerted) any RLN, LN20 20 Subscriber absent RPN RPN21 21 Call rejected U, RPN U, RPN22 31 Number changed any RLN, LN26 31 Non-selected user clearing any RLN, LN27 27 Destination out of order RPN RPN28 31 Invalid number format (address incomplete) any RLN, LN29 31 Facility rejected any RLN, LN30 31 Response to STATUS ENQUIRY any RLN, LN, LN31 31 Normal, unspecified U, LPN, RPN U, LPN, RPN34 31 No circuit/channel available any RLN, LN38 38 Network out of order RPN RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure RPN RPN42 42 Switching equipment congestion RPN RPN43 31 Access information discarded any RLN, LN

ETSI



44 31 Requested circuit/channel not available U, RPN U, RPN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified U, RPN U, RPN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN62 31 Inconsistency in designated outgoing access





does notany RLN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 31 Incompatible destination any RLN, LN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 31 Invalid message, unspecified any RLN, LN96 111 Mandatory information element is missing U, RPN RPN97 31 Message type non-existent or not implemented any RLN, LN98 31 Message not compatible with call state or



any RLN, LN

100 111 Invalid information element contents U, RPN RLN, LN101 31 Message not compatible with call state any RLN, LN102 102 Recovery on timer expiry U, RPN U, RPN103 31 Parameter non-existent or not implemented,



any RLN, LN


ETSI




no 31 or 1111 31 Unallocated (unassigned) number any RLN, LN2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 31 Normal call clearing any17 17 User busy U, RPN U, RPN18 18 No user responding any RLN, LN19 31 No answer from user (user alerted) any RLN, LN20 31 Subscriber absent any RLN, LN21 21 Call rejected U, RPN U, RPN22 22 Number changed any RLN, LN26 31 Non-selected user clearing any RLN, LN27 27 Destination out of order RPN RPN28 28 Invalid number format (address incomplete) any RLN, LN29 29 Facility rejected U, RPN U, RPN30 31 Response to STATUS ENQUIRY U, RPN RLN, LN31 31 Normal, unspecified U, RPN U,RPN34 31 No circuit/channel available any RLN, LN38 38 Network out of order RPN RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN41 41 Temporary failure RPN RPN42 31 Switching equipment congestion any RLN, LN43 31 Access information discarded any RLN, LN

ETSI



44 31 Requested circuit/channel not available any U, LPN, RPN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified U, RPN U, RPN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN62 31 Inconsistency in designated outgoing access





does notany RLN, LN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 88 Incompatible destination U U90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified any RLN, LN96 111 Mandatory information element is missing U, RPN U, RPN97 31 Message type non-existent or not implemented any RLN, LN98 111 Message not compatible with call state or



any RLN, LN

100 111 Invalid information element contents any RLN, LN101 111 Message not compatible with call state U, RPN RLN, LN102 31 Recovery on timer expiry any RLN, LN103 31 Parameter non-existent or not implemented,



any RLN, LN


ETSI




no 31 or 111 --- RLN, LN1 31 Unallocated (unassigned) number any RLN, LN2 31 No route to specified transit network any RLN, LN3 31 No route to destination any RLN, LN4 31 Send special information tone any RLN, LN5 31 Misdialled trunk prefix any RLN, LN6 31 Channel unacceptable any RLN, LN7 31 Call awarded and being delivered in an


8 31 Preemption any RLN, LN9 31 Preemption – circuit reserved for reuse any RLN, LN16 16 Normal call clearing U, RPN U, RPN17 31 User busy any RLN, LN18 31 No user responding any RLN, LN19 31 No answer from user (user alerted) U, RPN U, RPN20 31 Subscriber absent any LPN, RPN21 31 Call rejected any RLN, LN22 31 Number changed any RLN, LN26 31 Non-selected user clearing any RLN, LN27 27 Destination out of order RPN RPN28 31 Invalid number format (address incomplete) any RLN, LN29 31 Facility rejected any RLN, LN30 31 Response to STATUS ENQUIRY U, RPN RLN, LN, LN31 31 Normal, unspecified U, RPN U, RPN34 31 No circuit/channel available any RLN, LN38 38 Network out of order RPN RPN39 31 Permanent frame mode connection out of

serviceany RLN, LN

40 31 Permanent frame mode connection operational any RLN, LN

ETSI



41 41 Temporary failure RPN RPN42 42 Switching equipment congestion RPN RPN43 31 Access information discarded any RLN, LN44 31 Requested circuit/channel not available any RLN, LN46 31 Precedence call blocked any RLN, LN47 31 Resource unavailable, unspecified any RLN, LN49 31 Quality of service unavailable any RLN, LN50 31 Requested facility not subscribed any RLN, LN53 31 Outgoing calls barred within CUG any RLN, LN55 31 Incoming calls barred within CUG any RLN, LN57 31 Bearer capability not authorized any RLN, LN58 31 Bearer capability not presently available any RLN, LN62 31 Inconsistency in designated outgoing access





does notany RLN, LN


clearedany RLN, LN

87 31 User not member of CUG any RLN, LN88 31 Incompatible destination any RLN, LN90 31 Non-existent CUG any RLN, LN91 31 Invalid transit network selection any RLN, LN95 95 Invalid message, unspecified any RLN, LN96 111 Mandatory information element is missing any RLN, LN97 31 Message type non-existent or not implemented any RLN, LN98 111 Message not compatible with call state or



any RLN, LN

100 111 Invalid information element contents any RLN, LN101 111 Message not compatible with call state any RLN, LN102 31 Recovery on timer expiry any RLN, LN103 31 Parameter non-existent or not implemented,



any RLN, LN


ETSI


Annex B (informative):BibliographyISO/IEC 9646-2 (1994): "Information technology - Open Systems Interconnection - Conformance testing methodologyand framework - Part 2: Abstract Test Suite specification".

ISO/IEC 9646-5 (1994): "Information technology - Open Systems Interconnection - Conformance testing methodologyand framework - Part 5: Requirements on test laboratories and clients for the conformance assessment process".

ITU-T Recommendation F.200: "Teletex service".

ITU-T Recommendation F.220: "Service requirements unique to the processable mode number eleven (PM11) usedwithin the teletex service".

ITU-T Recommendation F.230: "Service requirements unique to the mixed mode (MM) used within the teletexservice".

ETSI


History

Document history

V1.1.1 February 2001 Public Enquiry PE 20010608: 2001-02-07 to 2001-06-08

V1.1.1 July 2001 Vote V 20010921: 2001-07-23 to 2001-09-21

Integrated Services Digital Network (ISDN); Signalling System … · Final draft ETSI EN 300...

Documents

Transcript of Integrated Services Digital Network (ISDN); Signalling System … · Final draft ETSI EN 300...