INSTRUCTIONS KIT BEAR CHAIR BC201

1.

2.

3.

4. 5.5.

6.

8.

8.

4.

3.

4.

9.

11.

12.

13.

7.

14.

10.

1.

Parts list:

NR. parts Quanty 1. Legs 2 2. Seat slats 6 3. Arm support 2 4. Triangles 2 5. Arms 2 6. Additional Arm Support 2 7. Struts 2 8. Sides , left (L) en right (R) 2 9. Bottom Back Support 110. Back Slats 711. Top Back Support 112. Frontm Slat 113. Comfort Slat 1 14. Plated Screws 6814. Brass Plaque 1

Note: Put any loose parts ordered on the ground and check the numbers! Shed there, where necessary, rough parts are smooth. Check before you glued, or glueing the right parts. Read the installation requirements before you begin. Good luck with the installation!

Bear chair NederlandPostbus 500

3700 AM Zeist

Original Bear Chair BC201

Set the bottom back support (9) and top back support (11) on a flat surface with the curved sides and countersunk holes facing up. Arrange the seven back slats (10) with the longest in the centre, on the supports.

9.

11.10.

step 1.

Push al the slats together so that there is even spacing on each side. Screw only the centre slat down using screws in the pre-drilled holes**Before tightening has screwed this slats, first apply a very thin layer of glue (Tec7) in the middle of the bar screwing.

step 2.

Space the slats out evenly, from the centre attached slat, so that the shortest outside slats are even with end of the curve on the back supports, and then attach. Use a thin slat as a template. When the top is nice and round, you can the slats glued (Tec7) and screw.

step 3.

Attach the legs (1) to the sides (8) using four screws in the pre-drilled holes as shown. Line up the screws with the pilot holes on the leg. Each leg and side are marked either “L” for left and “R” for right, and should be matched together.

step 4.8.

1.

8.1.

Place the two sides (8) marked “L” and “R” facing each other with the legs on the outside. The “R” should be on the right side of the chair (as sitting) Attach the front slat (12) to the front of the sides as shown. Using four screws and use Tec7.

step 5.

8.

8.

12.

Place back assembly into the cut out area on the sides as shown, attach with two screws through the pre-drilled holes.Don’t forget Tec7!

step 6.

Look carefully before you fix anything!

Place the comfort slat (13) and six seat slats(2) on the sides as shown in the picture, and space out evenly, leaving a small gap between the comfort slat and the back assembly.

step 7.2.

13.

2.

Attach each arm support(3) to the tops of the legs with two screws. Push a triangle (4) into the right angled corner (lining up the two pre-drilled holes in the leg and the centre pre-drilled hole on the arm support) and attach with three screws. Repeat on the other side. Use Tec7.

step 8.3.

4.

Attach the top of the struts (7) to the underside of the top back support (11) with two screws in the pre-drilled holes. If the back assembly is noticeably leaning off centre, grasp it firmly and move it left or right until the bottom of the struts can be attached without twisting or bending them. Attach the bottom of the struts to the sides with one screw each for now. Do not apply glue here yet.

step 9.

7.7.

Attach the back of the arm (5) to the strut with one screw through the pre-drilled hole on the strut. Attach the front of the arm to the arm support (3) with two screws from the under side.

step 10.

First drill a hole with 3 mm wood drill bit Use glue Tec7!

Place the chair on a flat surface and make sure it is sitting solid on both legs and both sides. If it is not sitting flat, remove the single screw holding the bottom of the strut down and move the strut up or down to compensate. When the adjustments are done, attach the struts with two screws each (and glue Tec7).

step 11.

Attach the additional arm support (#6) to the inside of the struts, underneath the back of the arms through the pre-dril-led holes with four screws. Pre-drill with a wood drill bit (3 mm) is recommended.

step 12.

6.

Knock the caps under the legs and fit the brass plate on the front of the chair.

step 13.

Remove any adhesive from the chair and sanding rough parts smooth. Your seat is ready for use.

step 14.

Zet op vlakke ondergrond

Enjoy your Bear chair

ALWAYS CHECK THE LOOSE PARTS :You have purchased a kit of the BC201 . This kit box packed with care . If, after thechecking nevertheless appear that parts are missing or damaged , please within 7 days, preferably by email to contact us . If necessary, take photos and send it along .We will contact you as soon as possible .

You have chosen a kit box . The supplier is responsible for the supplied looseparts. You are responsible for assembling !

Use only the screws ! These are made of stainless steel and do not rust .

Use only a Canadian Bitje , guaranteed to turn the screws otherwise broken.

Use for bonding only Tec7 . This adhesive is suitable for indoor and outdoor use . In all weathers . Always bonding portion light rub , not both parts !

Cedar wood is light and delicate. So beware of dents . Tighten the screws . But beware : fixed is fixed !

If you follow the above steps carefully , you can mount the seat in a good way . We wish you much fun with the bear chair , and refer to service to our website .

team of Bear chair Europe

Conditions of self-assembly.

Bear chair NederlandPostbus 500

3700 AM Zeist

info@the-bearchair.nlwww.the-bearchair.nl

0343-513741

11.

6.

7.

3 mm drill Canadian bitjeµ