Installing v-Ribbed Belt
-
Upload
buerebista -
Category
Documents
-
view
226 -
download
0
Transcript of Installing v-Ribbed Belt
7/28/2019 Installing v-Ribbed Belt
http://slidepdf.com/reader/full/installing-v-ribbed-belt 1/3
FABIA 2000➤ 1.2/40; 1.2/47 Engine, Mechanical Components
Removing and installing V-ribbed beltEdition 08.02
S00.5322.00.2013-1 page 1
13
13-1 Removing and installing V-ribbed belt
Summary of components
♦ Mark the rotation direction before removing the V-ribbed belt. Reversing the rotation direction of an already used belt may destroy it.
♦ Pay attention to the correct position of the V-ribbed belt in the belt pulley when installing it.
♦ Vehicles without an air-conditioning system do not have an air-conditioning compressor or guide pulley.
1 - 22 Nm
2 - Belt pulley
❑ on the coolant pump
3 - Trim4 - Tensioner with tensioning
pulley
❑ do not remove the tensioningpulley.
5 - 40 Nm
6 - Generator
❑ to facilitate positioning of thegenerator on the cylinderblock, drive the threadedbushings of the screwsslightly backwards
7 - Guide pulley8 - Washer
❑ Camber towards the outside
9 - Belt pulley
❑ for crankshaft
10 - 90 Nm + torque a further 90 (1 / 4 turn)
❑ replace
❑ interlock the crankshaft witha drift -T10121- for looseningand tightening it up
⇒ Chapter 13-311 - Distance sleeve
❑ for generator
12 - 23 Nm
13 - Distance sleeve
❑ for the AC compressor
14 - Dowel sleeves for AC compressor
❑ must be inserted in the cylinder block
15 - V-ribbed belt
❑ Routing of the V-ribbed belt
vehicles without air conditioning⇒ Fig. 1 in 13-1 page 2
Vehicles with air conditioning⇒ Fig. 2 in 13-1 page 3❑ removing and installing⇒ 13-1 page 2
13 – Crankgear
Note
7/28/2019 Installing v-Ribbed Belt
http://slidepdf.com/reader/full/installing-v-ribbed-belt 2/3
FABIA 2000➤ 1.2/40; 1.2/47 Engine, Mechanical Components
Removing and installing V-ribbed belt Edition 08.02
S00.5322.00.2013-1 page 2
13
Removing
– Mark the rotation direction of the V-ribbed belt.
– Lever off the cover for the tensioning roller -A-.
– Swing out the tensioning roller -A- with Torx key 50 -B-
in the direction of travel up to the stop and remove theV-ribbed belt.
The tensioning roller can be interlocked by inserting a rig pin.
Installing
♦ Inspect V-ribbed belt ⇒ Inspection and Maintenance.
♦ Before fitting the V-ribbed belt make sure that all as- semblies (generator, coolant pump and AC compres- sor) are securely mounted.
♦ Check smooth operation of belt pulley, tensioning and guide pulley.
♦ Pay attention to the rotation direction of already used V-ribbed belts.
– Position the V-ribbed belt on the belt pulleys and
guide pulley.
– Swing out the tensioning roller -A- with Torx key 50 -B-
in the direction of travel up to the stop and lay the V-ribbed belt in place.
– Press on the cover of the tensioning roller -A-.
– Start engine and check belt run.
Fig. 1: V-ribbed belt run - without an air condition-ing system
1 - Belt pulley - crankshaft
2 - Belt pulley - coolant pump
3 - Tensioning pulley
4 - Belt pulley - generator
Note
Note
7/28/2019 Installing v-Ribbed Belt
http://slidepdf.com/reader/full/installing-v-ribbed-belt 3/3
FABIA 2000➤ 1.2/40; 1.2/47 Engine, Mechanical Components
Removing and installing V-ribbed beltEdition 08.02
S00.5322.00.2013-1 page 3
13
Fig. 2: V-ribbed belt run - with an air conditioningsystem
1 - Belt pulley - crankshaft
2 - Belt pulley - coolant pump
3 - Tensioning pulley
4 - Belt pulley - generator
5 - Belt pulley - AC compressor
6 - Guide pulley