Certified to comply with ANSI A112.18.1M

ROUGHING-INDIMENSIONS

Required Tools

Wrench(Supplied)

Turn off hot and cold watersupplies before beginning.CAUTION1 2

Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.Make sure that the RUBBER RING (2) is properly seated in RECESSat base of SPOUT (3).Assemble RUBBER WASHER (4) and BRASS WASHER (5) ontoSHANK (1). From underside of ledge secure SPOUT (3) into positionwith LOCKNUT (6).

SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY

Prepare TUBE and TEE ASSEMBLY (1) to fit center to centerVALVE (2) location (between 6-1/2" and12"). If necessary,cut and/or bend TUBING carefully. Make sure tube bend isclose to the TEE (1) so that it will not effect the compressionjoint at the VALVE CONNECTION.

Remove COUPLING NUT (3) and FERRULE (4) from eachVALVE (2) and slide onto TUBING (5).

Adjustable Wrench

Channel Locks

7184.9007184.901

Flat Blade Screwdriver

VALVE inlet is 3/4-inchNPT male connector.

NOTE

2

ADJ. 6-1/2 TO 12

43

1

34

5

RECESS

3

1

2

4

6

5

MOUNTINGSURFACE.

MOUNTINGSURFACE

10-1/4"(262mm)

6-3/4"(172mm)

3-3/4"(97mm)

4"(102mm)

11-1/4"(287mm)

Phillips Screwdriver

DECK-MOUNT BATH FILLER

InstallationInstructions

Thank you for selecting American-Standard...the benchmarkof fine quality for over 100 years.

To ensure that your installation proceeds smoothly--pleaseread these instructions carefully before you begin.

6-1/2" to 12"(165mm to 305mm)

14-3/4" (377mm)

1-1/2 MAX.(38mm) MAX.1-3/16" MAX.

(30mm) MAX.

1-3/16 D.(30mm) D.

3'(76mm)

(H) (C)

1-1/8 D.

12 MAX.(305mm)

1-1/16 D.(27mm) D.

3/4-14 MALEN.P.T. INLETS

M965466 Rev. 1.2

TIME SQUARE™

10

3

55/16'' MIN. MOUNTING SURFACE

11

11

10

11

1

3Push TUBING (4) ends into VALVE (5) side outlets. Insert VALVES (5)into mounting holes from underside of ledge.

Install LOCKNUTS (1) and RUBBER WASHERS (3) onto valve shanks.

Place RUBBER RING (11) into DECK ADAPTERS (10) and thread ontovalves until snug against internal stop.

Tighten LOCKNUT (1) to secure VALVE (5) position.

Slide FERRULE (13) and COUPLING NUT (14) to outlet of VALVE (5) and tightenCOUPLING NUT (14) firmly.

Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet ofright VALVE using appropriate connector.

VALVE ASSEMBLY

HOT

COLD

13

5

14

8

7

99a

6

14

134 5

10

MOUNTINGLEDGE

DECKADAPTER

4 INSTALL HANDLES

Turn VALVE to OFF position.

Push ADAPTER (1) on VALVE STEM (2), so that the hole of theADAPTER (1) without a spline is facing up. Fig. A. TightenSTEM SCREW (3) to secure ADAPTER (1).

Align male teeth on DECK ADAPTER (5) to female teeth in LEVER HANDLEASSEMBLY (4). Push LEVER HANDLE ASSEMBLY (4) onto DECKADAPTER (5) flush against mounting surface.

Tighten SET SCREW (6) with HEX WRENCH supplied to secureLEVER HANDLE ASSEMBLY (4). View A.

FOR FITTINGLESS SPRAY

Press TEE (6) onto SPOUT SHANK (7) making certain that the O-RING (8) isproperly seated on SHANK (7). Push COUPLING (9 or 9a) into TEE (6) andattach to SPOUT SHANK (7) and tighten. Note: For product with HandShower, COUPLING (9) is tightened using a 10mm (3/8”)Hex Wrench.

1

23

5

6

4

TOP

MALE TEETHSPLINE END DOWN

Fig. A.

View. A.

FEMALE TEETH

View. A.

HEX WENCHSUPPLIED

M965466 Rev. 1.2

8To change direction of handle rotation, proceed as follows:

Turn valve to OFF position.Loosen SET SCREW (1) and pull ofHANDLE ASSEMBLY (2). Loosen HANDLE SCREW (3) and pull offHANDLE ADAPTER (4).Remove SPRING CLIP (5).Lift STOP WASHER (6), turn 90° and replace.Replace SPRING CLIP (5).Refer to step four for HANDLE ASSEMBLY (2)instructions.

If spout drips, operate handles several timesfrom OFF to ON position. Do not force - handlesturn only 90°.

SERVICE 9

HANDSHOWER INSTALLATION (Model 7184.901 series only)

TEST INSTALLED FAUCET6Turn VALVES "off" and attach handles.

Lift HANDSHOWER from HOLDER, direct spray into tub, liftTRANSFER KNOB to check HANDSHOWER and HOSES for leaks.Turn handles "off."

Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max fromSPOUT center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) BRASS WASHER (4) and LOCKNUT from underside of ledge.

Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT.

Add SEAL WASHER (5) and connect HOSE (10) to outlet nippleat the bottom of COUPLING (7). Tighten firmly.

Slip SHOWER HOSE (8) with COUPLING NUT through SPRAYESCUTCHEON (1). Install SEAL (9) and connect both HOSES (8)and (10), Connect HAND SHOWER (11) to SPRAY HOSE (8).

When not in use, HANDSHOWER should be seated in the HOLDER.

NOTE

5

With handles in "off" position, turn on water supplies and checkall connections for leaks.Operate both handles and flush water lines thoroughly.Check SPOUT mounting for leaks.

The flow rate of this Tub Filler exceeds 20 gallons/minuteat higher water pressure. Do not fill bathtub unattended.

CAUTION

12

34

57

810

9

911

6

LOCKNUT

DO: SIMPLY RINSE THE PRODUCTCLEAN WITH CLEAR WATER.DRYWITH A SOFT COTTON FLANNELCLOTH.

DO NOT: DO NOT CLEAN THEPRODUCT WITH SOAPS, ACID,POLISH, ABRASIVES, HARSHCLEANERS, OR A CLOTH WITHA COARSE SURFACE.

CARE INSTRUCTIONS:

1

2

3

4

5

6

HEX WENCHSUPPLIED

Hex wench(supplied)

Before the bathroom is completely finished, you may want to remove spout, handshower, and handles to avoid damage during construction.

To remove handles, reverse steps in section 4.

To remove SPOUT (1), proceed as follows:

Unthread LIFT ROD KNOB (2) and remove.

Remove PLUG BUTTON (3) and remove SET SCREW (4) using

Lift SPOUT (1) off SHANK (5) carefully and remove RUBBERRING (6).Unthread SHANK SLEEVE (7) and remove from SHANK (5).

Reverse sequence to re-install SPOUT (1). Be sure RUBBERRING (6) is properly seated in its recess at the base of theSPOUT (1). Make certain SET SCREW (4) is properly alignedand tight so that SPOUT (1) is locked in place.

1

8

2

34

6

5

7

VIEW "A"

VIEW "A"

7

90°

M965466 Rev. 1.2

918049-0070AHANDLE ADAPTER

M962849-0070ASTREAM STRAIGHTENER

028679-0070ATUBE & TEEASSEMBLY

012668-0070ASHANK KIT

030274-0070ASHANK

MOUNTING KIT

A912629-0070ARUBBER RING

M917161-0070ASET SCREW

012078-0070AVALVE COUPLING KIT

M964421-YYY0AHAND SHOWER

HOLDER

028699-0070ACOUPLING (FOR TRANSFER)

030275-0070ASHANK SLEEVE KIT

030278-0070ATRANSFERSEAL KIT

M964423-YYY0ASPOUT KIT (7184.900)

M964437-YYY0ASPOUT KIT (7184.901)

MODEL NUMBER

7184.900 / 7184.901

028698-0070ACOUPLING(LESS SPRAY)

M952454-0070ATRANSFER

ROD ASSEMBLY

DECK-MOUNT BATH FILLER

CHROMESATIN NICKEL

002295

Replace the "YYY" withappropriate finish code

M950332-YYY0AHAND SHOWER

M961634-0070AVALVE MTG. KIT

994053-0070ACARTRIDGE

M964417-0070ADECK ADAPTER KIT

M964416-YYY0ALEVER HANDLEASSEMBLY

918555-0070AHANDLE SCREW

M962575-YYY0ATRANSFER LIFT KNOB

For toll-free information and answers to your questions, call:1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. ESTIN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. ESTIN MEXICO 01-800-839-1200

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .© A S A m e r i c a , I n c . 2 0 1 3

HOT LINE FOR HELP

M918075-0070ASET SCREW

028667-0020AHAND SHOWER HOSE

A952849-0070ACHECK VALVE

051343-0070AHOSE KIT

TIME SQUARE™

M965466 Rev. 1.2