Installation Procedure · Model(s) "WSW 200-600" Horizontal & Vertical Expansion Control Systems...
33
Issued: 01/03/2019 P/N: 20102 Wabo® WeatherSeam Model(s) "WSW 200-600" Horizontal & Vertical Expansion Control Systems The following installation procedure is very important and must be fully understood prior to beginning any work. To ensure proper installation and performance of expansion joint system the following actions must be completed by the installing contractor. Failure to do so will affect product warranty. Carefully read and understand installation procedure. Contact WBA's Technical Service Department at (800) 677-4922 for product assistance. Inspect all shipments and materials for missing or damaged components and hardware. Contact Customer Service at (800) 677-4922 with WBA's order number and invoice for prompt assistance. Inspect substrate or adjacent construction for acceptance before beginning work. Report unacceptable construction to the project manager for scheduled repair work. Review WBA shop drawings for project specific detailed information if Engineering services were purchased at time of order. 1) 2) 3) 4) Installation Procedure Information provided herein, including but not limited to, any drawing, design, photograph, graphic, or statement(s) ("Materials") are proprietary and the property of Watson Bowman Acme Corporation ("Company"). Reproduction, translation, or reduction to any electronic medium or machine readable form, in whole or part, is strictly prohibited, except for the express purpose for which it has been furnished, without prior written consent of Company. All Materials contained herein are provided by Company for information purposes only. Company reserves the right to amend or withdraw any information contained in the Materials without notice. All technical or other advice by Company, whether verbal or written, concerning products, or the use of products in specific situations ("Advice") is given by Company and is used at the Users own risk. Watson Bowman Acme Corp. 95 Pineview Drive Amherst, NY 14228 phone: (716) 691-7566 fax: (716) 691-9239 website: www.wbacorp.com
Transcript of Installation Procedure · Model(s) "WSW 200-600" Horizontal & Vertical Expansion Control Systems...
Issued: 01/03/2019 P/N: 20102
Wabo® WeatherSeam
Model(s) "WSW 200-600"
Horizontal & Vertical Expansion Control Systems
The following installation procedure is very important and must be fully understood
prior to beginning any work. To ensure proper installation and performance of
expansion joint system the following actions must be completed by the installing
contractor. Failure to do so will affect product warranty.
Carefully read and understand installation procedure. Contact WBA's
Technical Service Department at (800) 677-4922 for product assistance.
Inspect all shipments and materials for missing or damaged components
and hardware. Contact Customer Service at (800) 677-4922 with WBA's
order number and invoice for prompt assistance.
Inspect substrate or adjacent construction for acceptance before
beginning work. Report unacceptable construction to the project manager
for scheduled repair work.
Review WBA shop drawings for project specific detailed information if
Engineering services were purchased at time of order.
1)
2)
3)
4)
Installation Procedure
Information provided herein, including but not limited to, any drawing, design, photograph, graphic, or statement(s) ("Materials") are proprietary and the property of Watson Bowman Acme Corporation ("Company"). Reproduction, translation, or
reduction to any electronic medium or machine readable form, in whole or part, is strictly prohibited, except for the express purpose for which it has been furnished, without prior written consent of Company. All Materials contained herein are
provided by Company for information purposes only. Company reserves the right to amend or withdraw any information contained in the Materials without notice. All technical or other advice by Company, whether verbal or written, concerning
products, or the use of products in specific situations ("Advice") is given by Company and is used at the Users own risk.
Watson Bowman Acme Corp. 95 Pineview Drive Amherst, NY 14228
phone: (716) 691-7566 fax: (716) 691-9239
website: www.wbacorp.com
Components shown below vary in size and profile
depending on model of system
Standard Components
"A"Model
Dimension Chart & Part Number
Part Number
Prima-Lub
(P/N - 2720)
"A"
Elastomeric Visual Seal
(For Part Number Refer to Chart, Black seal)
*
Optional Components for Splice Procedures. Place order for required Quantities
PP Primer
(P/N - 2717)
241F Adhesive
(P/N - 2716)
Moisture Barrier
(For Part Number Refer to Chart)
* *
Model Part Number"B"
Dimension Chart & Part Number
Butt Splice Clip
(P/N - 1192)
Splice Clip: Same Plane
(P/N - 1194)
Splice Clip: Vert to Horiz
(P/N - 1193)
Sheet
1
of 4
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
Installation procedure: "W
SC
" W
eatherS
eam
system
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Wall Mount
Aluminum Extrusion
(P/N - 1292)
Plastic Insert
(P/N - 5786)
1
4
" x 2
1
2
" Screw Anchor
(P/N - 5782)
**
*
NP-1 Sealant
(P/N - 2826)
2"WSW-200
3"WSW-300
1201
1204
WSW-400
WSW-500
WSW-600
4"
5"
1342
1262
6" 1362
WSW-200
WSW-300
1181
1181
WSW-400
WSW-500
WSW-600
1175
1175
1175
1 3/8"
1 3/8"
4 1/8"
4 1/8"
4 1/8"
Flush Condition
- Field measure all lengths and directional changes for aluminum extrusions to ensure their proper
layout where required. Mount extrusions to wall surface and install temporary wood blocking to
secure extrusions for field drilling operations. Wood blocking should be non-continuous to permit
field drilling anchor holes at required spacing.
* Note: Always review architectural plans for specific project requirements
- Apply continuous bead of NP-1 Sealant along back of the aluminum extrusions prior to
installation. (exterior only)
NP-1Sealant
*1
/4
"
Joint Opening
Wall Mount
Aluminum Extrusion
1
2
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
2
of 6
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
- Secure Aluminum Extrusions using appropriate Anchors supplied by manufacturer.
Note: Utilize Plastic Inserts for securing Aluminum Extrusions to wall, if wall construction is
either CMU or a Masonry wall.
- Field drill anchor holes at 18" O.C. (Max) along aluminum gauge line.
Drill through aluminum into adjacent construction.
Note: All mortar joints in exterior walls must be flush with face of masonry to ensure tight weather seal.
1
4
'
4
5
°
Gauge Line
1
4
" Dia. Screw
Anchor
3
4
Plastic Insert
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
3
of 6
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
- Before installing Moisture Barrier spread Prima-Lub adhesive into cavities of Aluminum
Extrusions. Ensure full engagement of locking lug.
Locking Lug
Moisture
Barrier
Prima-Lub
Locking Lug
- Before installing Visual Seal spread Prima-Lub adhesive into cavities of Aluminum extrusions.
Ensure full engagement of locking lug.
Visual Seal
5
6
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
4
of 6
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
Visual Seal
Prima Lub
Locking Lug
1. Cut ends of the WSW visual seal, with a sharp knife, to the desired angle using a formed jig with miter box
(supplied by contractor). Insure cuts are clean, straight and square.
2. Cleans ends of seal with a solvent to remove any foreign material.
3. Brush apply PP Primer to both seal ends to be joined together at splice.
4. Reassemble mitered ends of adjacent seals utilizing the reinforcing corner clips (for 90° transitions only).
5. Apply Aron Alpha 241F adhesive as specified by the manufacturer to one of the two seal surfaces to be
bonded.
6. Apply pressure bringing the two surfaces in tight contact immediately upon completing application of the
adhesive. Hold in place for approximately one to two minutes to allow adhesion.
7. Re-check quality of all miters or splices and apply additional adhesive if required to ensure proper miter or
splice.
8. Contact manufacturer for clarification of above procedure (if required) prior to proceeding with splicing visual
seal profile. It is usually recommended to allow 15 minutes time before installing spliced seal. Care shall be
excercised as a result that it takes 24 hours for adhesive to fully cure.
"WSW" Visual Seal Field Splice Procedures
Used for direction changes, Going around corners, Parapets, Etc
(Santoprene Only)
Horizontal Transition
Vertical Transition
ThermoPlastic
Visual Seal
Aluminum
Extrusion
Aluminum
Extrusion
Vinyl Functional
Seal
Vinyl Functional
Seal
Suggested Reinforcing
Corner Clips
Note: Clips only available
for 90° transititons
Bordens 241F Adhesive
(Prepare cut ends of seal with
Bordens PP Primer)
Part Number's 241F
Adhesive - 2716
PP Primer - 2717
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
4
of 4
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
In
sta
lla
tio
n p
ro
ce
du
re
: W
SW
W
ea
th
erS
ea
m syste
m
Sheet
6
of 6
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Wa
tso
n B
ow
ma
n A
cm
e C
orp
.
95
P
in
evie
w D
rive
A
mh
erst, N
Y 1
42
28
ph
on
e: (7
16
) 6
91
-7
56
6 fa
x: (7
16
) 6
91
-9
23
9
we
bsite
: w
ww
.w
ba
co
rp
.co
m
"WSW" Termination Detail
Can be used at the base of the WSW Seal Installation
Finished Wall
(By Others)
(Field Fabricated By Others)
Termination Boot (Neoprene) Base of exterior wall
Drip edge
Wabo®WeatherSeam
Expansion Joint System
1'-4
" (M
in
)
8" (M
in
)
1'-0
" (M
in
)
Varies
Varies (Note 1)
4" Min.4
"
M
i
n
.
V
a
r
i
e
s
(
N
o
t
e
1
)
8" (M
in
)
4
"
= Fold Lines
= Cut Lines
Represents Contact points when
assembling drainage boot. The
Dots must be touching and
bonded for a proper assembly.
Material: 1/32" Thick Neoprene
Sheetgood. (WBA P/n: 6300)
Use Jeene Profile Glue to fold
and bond side flaps together.
Notes:
1. Overall width of Boot Transition will be determined on the amount of movement the
WSW system can accommodate during normal movement ranges. WBA suggests
that the dimension will be at least Maximum Opening plus 1". This is to ensure that
there will not be any damage to the boot while the system is at maximum opening.
Issued: 8/31/15 p/n: 20198
Wabo® WeatherSeam
Model(s) "WSW 800, 1000 & 1200"
Horizontal & Vertical Expansion Control Systems
The following installation procedure is very important and must be fully understood
prior to beginning any work. To ensure proper installation and performance of
expansion joint system the following actions must be completed by the installing
contractor. Failure to do so will affect product warranty.
Carefully read and understand installation procedure. Contact WBA's
Technical Service Department at (800) 677-4922 for product assistance.
Inspect all shipments and materials for missing or damaged components
and hardware. Contact Customer Service at (800) 677-4922 with WBA's
order number and invoice for prompt assistance.
Inspect substrate or adjacent construction for acceptance before
beginning work. Report unacceptable construction to the project manager
for scheduled repair work.
Review WBA shop drawings for project specific detailed information if
Engineering services were purchased at time of order.
1)
2)
3)
4)
Installation Procedure
Information provided herein, including but not limited to, any drawing, design, photograph, graphic, or statement(s) ("Materials") are proprietary and the property of Watson Bowman Acme Corporation ("Company"). Reproduction, translation, or
reduction to any electronic medium or machine readable form, in whole or part, is strictly prohibited, except for the express purpose for which it has been furnished, without prior written consent of Company. All Materials contained herein are
provided by Company for information purposes only. Company reserves the right to amend or withdraw any information contained in the Materials without notice. All technical or other advice by Company, whether verbal or written, concerning
products, or the use of products in specific situations ("Advice") is given by Company and is used at the Users own risk.
Watson Bowman Acme Corp. 95 Pineview Drive Amherst, NY 14228
phone: (716) 691-7566 fax: (716) 691-9239
website: www.wbacorp.com
Components shown below vary in size depending
on model of system
Standard Components
4"WSW-800
"A"Model
Dimension Chart & Part Number
5"WSW-1000
1342
Part Number
1262
Wall Mount Aluminum
Extrusion (Exterior)
(P/N - 1296)
Plastic Insert
(P/N - 5786)
1
4
" x 2
1
2
" Screw Anchor
(P/N - 5782)
*
*
"A"
WSW-1200 6" 1362
Elastomeric Visual Seal
NP-1 Sealant (P/N - 2826)
*
Optional Components for Splice Procedures. Place order for required Quantities
241F Adhesive
(P/N - 2716)
Moisture Barrier
(P/N - 1175)
*
Butt Rail Splice Plate
Aluminum (P/N - 8366)
*
90° Rail Splice Plate
Aluminum (P/N - 8365)
*
Self-Centering Bar
1'-6 3/8"WSW-800
"B"Model
Dimension Chart & Part Number
1'-10 3/8"WSW-1000
15630
Part Number
15631
WSW-1200 2'-2 3/8" 15603
1
4
" Dia x 2" Bolt
(P/N - 4837)
Aluminum Center Profile
(Interior)
(P/N - 1294)
Aluminum Center Profile
(Exterior)
(P/N - 1293)
Wall Mount Aluminum
Extrusion (Interior)
(P/N - 1295)
#10-24 x
1
2
" Lg Csk. Screw
(P/N - 5573)
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
1
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
90° Horiz. Rail Splice Plate
Aluminum (P/N - 8364)
*
PP Primer
(P/N - 2717)
Horiz. to Vert. Splice Clip
Seal only (P/N: 1194)
*
*
Butt Splice Clip
Seal only (P/N: 1192)
*
Horiz. to Horiz. Splice Clip
Seal only (P/N: 1193)
*
Prima-Lub (P/N - 2720)
Flush Condition
- Apply continuous bead of NP-1 Sealant along back of the aluminum extrusions prior to installation.
(exterior only)
NP-1 Sealant
1
4
"
*
Joint Opening
Wall Mount
Aluminum Extrusion
- Field measure all lengths and directional changes for aluminum extrusions to ensure their proper
layout where required. Temporarily fix extrusions to wall surface in position as shown for field
drilling operations.
* Note: Always review architectural plans for specific project requirements
Note: Review entire procedure before beginning. If step 7 is not possible due to limited space
follow steps 5-7 first outside of joint opening, then do steps 1-4 and then install seals.
1
2
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
2
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
- Field drill anchor holes at 18" O.C. (Max) along aluminum gauge line. Drill through aluminum into
adjacent construction on a 45° angle.
Note: All mortar joints in exterior walls must be flush with face of masonry to ensure tight weather
seal.
1/4" Dia.
Screw Anchor
1/4
"
*
Joint Opening
3
4
5
°
Gauge Line
- Secure aluminum extrusions using appropriate anchors supplied by manufacturer.
Note: Utilize plastic inserts for securing Aluminum Extrusions to wall, if wall construction is either CMU
or a Masonary wall.
4
1/4
"
*
Joint Opening
Plastic Insert
3 1
/4
" @
E
xte
rio
r
2 3
/8
" @
In
te
rio
r
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
3
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
- Set center extrusion with self-centering bars into joint opening sliding the spheroid ends of the
bars into the circular cavity of the edge extrusions. Adjust bars to correct spacing (18" O.C.) one at
a time and drill in the #10 - 24 x 1/2" csk flat head self tapping screw into the center extrusion bolt
cavity below the bolt head at proper spacing to hold self-centering bars in place.
Note: If area to perform step 7 is limited refer to the general note on page 2 on optional method of
assembly.
- Thread 1/4" dia. Bolt thru self-centering bar to achieve dimension shown.
- Slide bolt into the center extrusion spaced at 18" O.C. Adjust self-centering bar to achieve
dimensions indicated.
1-7
/1
6"
3-1
/4
" @
E
XT
ER
IO
R
2-3
/8
@
IN
TE
RIO
R
5
1/4" Dia. x 2" Lg Bolt
Self-Centering
bar
6
7
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
4
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
- Brush apply prima-lub adhesive into extrusion cavity and install visual seals. Ensure full
engagement of the lug.
- Brush apply prima-lub adhesive into extrusion cavity and install functional seals/moisture
barriers. Ensure full engagement of the lug.8
Locking Lug
Prima-Lub
Moisture
Barrier
9
Locking Lug
Prima-Lub
Visual Seal
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
5
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
2 1/2"
2 1/2"
2 1/2" 2 1/2"
Interior Extrusion Splice Details
Exterior Extrusion Splice Details
Splice Location
Splice Plate
SW Centering
Extrusion
90° Splice Plate
SW Centering
Extrusion
Horizontal to
Vertical Splice
Side Elevation
Horizontal to Horizontal Butt Splice
or
Vertical to Vertical But Splice
2"
2 1
/2
"
2 1/2"
Splice Plate
Horizontal to Horizontal 90° Splice
SW Centering
Extrusion
#10-24 x
3
8
" Round
Head Self-Tapping
Screw
1/2
"
1/4"
Horizontal to
Horizontal 90° Splice
Splice Plate
SW Centering
Extrusion
#10-24 x
3
8
" Round
Head Self-Tapping
Screw
1/2
"
Horizontal to Horizontal Butt Splice
or
Vertical to Vertical But Splice
Horizontal to
Vertical Splice
2
1
2
"
2
1
2
"
90° Splice Plate
SW Centering
Extrusion
Side Elevation
Splice Location
SW Centering
Extrusion
Splice Plate
2"
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
6
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
1. Cut ends of the WSW visual seal, with a sharp knife, to the desired angle using a formed jig with miter box
(supplied by contractor). Insure cuts are clean, straight and square.
2. Cleans ends of seal with a solvent to remove any foreign material.
3. Brush apply PP Primer to both seal ends to be joined together at splice.
4. Reassemble mitered ends of adjacent seals utilizing the reinforcing corner clips (for 90° transitions only).
5. Apply 241F adhesive as specified by the manufacturer to one of the two seal surfaces to be bonded.
6. Apply pressure bringing the two surfaces in tight contact immediately upon completing application of the
adhesive. Hold in place for approximately one to two minutes to allow adhesion.
7. Re-check quality of all miters or splices and apply additional adhesive if required to ensure proper miter or
splice.
8. Contact manufacturer for clarification of above procedure (if required) prior to proceeding with splicing visual
seal profile. It is usually recommended to allow 15 minutes time before installing spliced seal. Care shall be
excercised as a result that it takes 24 hours for adhesive to fully cure.
"WSW" Visual Seal Field Splice Procedures
Used for direction changes, Going around corners, Parapets, Etc
(Santoprene Only)
Horizontal Transition
Vertical Transition
ThermoPlastic
Visual Seal
Aluminum
Extrusion
Aluminum
Extrusion
Moisture Barrier
Seal
Moisture Barrier
Seal
Suggested Reinforcing
Corner Clips
NOTE: Clips available for
90° transititons only
Aron Alpha 241F Adhesive
(Prepare cut ends of seal with
PP Primer)
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
7
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
8
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
"WSW" Termination Detail
Can be used at the base of the WSW Seal Installation
Expansion Joint System
Wabo Weatherseam
Finished Wall
(By Others)
(Field Fabricated By Others)
Termination Boot (Neoprene) Base of exterior wall
Drip edge
1'-4" (M
in)
8" (M
in)
1'-0" (M
in)
Varies
Varies (Note 1)
4" Min.4
"
M
i
n
.
V
a
r
i
e
s
(
N
o
t
e
1
)
8" (M
in)
4
"
= Fold Lines
= Cut Lines
Represents Contact points when
assembling drainage boot. The
Dots must be touching and
bonded for a proper assembly.
Material: 1/32" Thick Neoprene
Sheetgood. (WBA P/n: 6300)
Use Jeene Profile Glue to fold
and bond side flaps together.
Notes:
1. Overall width of Boot Transition will be determined on the amount of movement the
WSW system can accommodate during normal movement ranges. WBA suggests
that the dimension will be at least Maximum Opening plus 1". This is to ensure that
there will not be any damage to the boot while the system is at maximum opening.
Issued: 01/04/2019 P/N: 20199
Wabo® WeatherSeam
Professional & Traffic Series
Model(s) "WSW 900, 1500 & 1800"
Horizontal & Vertical Expansion Control Systems
The following installation procedure is very important and must be fully understood
prior to beginning any work. To ensure proper installation and performance of
expansion joint system the following actions must be completed by the installing
contractor. Failure to do so will affect product warranty.
Carefully read and understand installation procedure. Contact WBA's
Technical Service Department at (800) 677-4922 for product assistance.
Inspect all shipments and materials for missing or damaged components
and hardware. Contact Customer Service at (800) 677-4922 with WBA's
order number and invoice for prompt assistance.
Inspect substrate or adjacent construction for acceptance before
beginning work. Report unacceptable construction to the project manager
for scheduled repair work.
Review WBA shop drawings for project specific detailed information if
Engineering services were purchased at time of order.
1)
2)
3)
4)
Installation Procedure
Information provided herein, including but not limited to, any drawing, design, photograph, graphic, or statement(s) ("Materials") are proprietary and the property of Watson Bowman Acme Corporation ("Company"). Reproduction, translation, or
reduction to any electronic medium or machine readable form, in whole or part, is strictly prohibited, except for the express purpose for which it has been furnished, without prior written consent of Company. All Materials contained herein are
provided by Company for information purposes only. Company reserves the right to amend or withdraw any information contained in the Materials without notice. All technical or other advice by Company, whether verbal or written, concerning
products, or the use of products in specific situations ("Advice") is given by Company and is used at the Users own risk.
Watson Bowman Acme Corp. 95 Pineview Drive Amherst, NY 14228
phone: (716) 691-7566 fax: (716) 691-9239
website: www.wbacorp.com
J:\MARKETING\Media\Logos Signatures & Symbols\Logos\Approved_WBA_Logos\Jpegs\WBA Blue.jpg
Components shown below vary in size depending
on model of system
Standard Components
3"WSW-900
"A"Model
Dimension Chart & Part Number
5"
1204
Part Number
1262
Wall Mount
Aluminum Extrusion
(Exterior)
(P/N - 1296)
Plastic Insert
(P/N - 5786)
1
4
" x 2
1
2
" Screw Anchor
(P/N - 5782)
*
*
"A"
6" 1362
Elastomeric Visual Seal (For Part Number Refer to Chart)
*
Optional Components for Splice Procedures. Place order for required Quantities
Moisture Barrier (For Part Number Refer to Chart)
Aluminum Center
Profile
(Interior)
(P/N - 1294)
Aluminum Center Profile
(Exterior)
(P/N - 1293)
Wall Mount
Aluminum Extrusion
(Interior)
(P/N - 1295)
#10-24 x
1
2
" Lg Csk. Screw
(P/N - 5573)
WSW-1500
WSW-1800
1 3/8"WSW-900
"B"Model
Dimension Chart & Part Number
1181
Part Number
1175
1175
WSW-1500
WSW-1800
"B"
4 1/8"
4 1/8"
Pantagraph
(P/N - 15500)
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
1
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
NP-1 Sealant
(P/N - 2826)
Prima-Lub
(P/N - 2720)
J:\MARKETING\Website-Product Info\Accessories\WaboPrimaLub Adhesive - Bridge-Park\Images\PrimaLube_ productDetail_mainImage.jpg
Flush Condition
- Apply continuous bead of NP-1 Sealant along back of the Aluminum Extrusions prior to
installation. (Exterior Only)
NP-1Sealant
1
4
"
*
Joint Opening
Wall Mount
Aluminum Extrusion
- Field measure all lengths and directional changes for Aluminum Extrusions to ensure their proper
layout where required. Temporarily fix Extrusions to wall surface in position as shown for field
drilling operations.
* Note: Always review architectural plans for specific project requirements
NOTE: Review entire procedure before beginning. If step 7 is not possible due to limited
space follow steps 5-7 first outside of joint opening, then do steps 1-4 and then install seals.
1
2
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
2
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
- Field drill anchor holes at 18" O.C. (Max) along aluminum gauge line. Drill through
aluminum into adjacent construction on a 45° angle.
Note: All mortar joints in exterior walls must be flush with face of masonry to ensure tight
weather seal.
1
4
" Dia. Screw
Anchor
1
4
"
*
Joint Opening
3
4
5
°
Gauge Line
- Secure Aluminum Extrusions using appropriate anchors supplied by manufacturer.
Note: Utilize plastic inserts for securing Aluminum Extrusions to wall, if wall construction is
either CMU or a Masonary wall.
4
1
4
"
*
Joint Opening
Plastic Insert
3
1
4
" @
E
xte
rio
r
2
3
8
" @
In
te
rio
r
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
3
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
3 1
/4
" @
E
xte
rio
r
2-3
/8
@
In
te
rio
r
5
1
4
" Dia. x 2" Lg
Bolt Pantagraph
6
7
Set Center Extrusions with Pantographs into joint opening sliding the spherical ends of the Pantograph
into the circular cavity of the edge Extrusions. Adjust Pantographs to correct spacing (30" O.C.) one at
a time and drill in the # 10 -24 x 1/2" csk Flathead Self Tapping Screw into the Center Extrusion Bolt
cavity below the bolt head at proper spacing to hold the Pantograph in place.
NOTE: If area to perform step 7 is limited, refer to the general Note on page 2 for optional method of
assembly.
Adjust 1/4" Ø. Bolts on the Pantographs to achieve dimension shown.
Adjust bolts in Pantographs to achieve dimension show and slide bolt head into center extrusion cavity.
1
7
16
"
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
4
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
Brush apply Prima-Lub adhesive into extrusion cavity and install functional seals/Moisture Barriers.
Ensure full engagement of the lug.8
9
Brush apply Prima-lub adhesive into the extrusion cavity and install visual seals. Ensure full
engagement of the lug.
Prima-Lub
Locking Lug
Moisture Barrier
Locking Lug Visual Seal
Prima-Lub
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
5
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
1 1/2"
1 1/2"
1 1/2" 1 1/2"
Interior Extrusion Splice Details
Exterior Extrusion Splice Details
Splice Location
Splice Plate
SW Centering
Extrusion
90° Splice Plate
SW Centering
Extrusion
Horizontal to
Vertical Splice
Side Elevation
Horizontal to Horizontal Butt Splice
or
Vertical to Vertical But Splice
2"
2
1
2
"
2
1
2
"
Splice Plate
Horizontal to
Horizontal 90° Splice
SW Centering
Extrusion
#10-24 x
3
8
" Round
Head Self-Tapping
Screw
1
2
"
1
4
"
Horizontal to
Horizontal 90° Splice
Splice Plate
SW Centering
Extrusion
#10-24 x
3
8
" Round
Head Self-Tapping
Screw
1
2
"
Horizontal to
Horizontal Butt Splice
or
Vertical to Vertical But
Splice
Horizontal to
Vertical Splice
2
1
2
"
2
1
2
"
90° Splice Plate
SW Centering
Extrusion
Side Elevation
Splice Location
SW Centering
Extrusion
Splice Plate
2"
Installation procedure: W
SW
W
eatherS
eam
system
Sheet
6
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
1. Cut ends of the WSW visual seal, with a sharp knife, to the desired angle using a formed jig with miter box
(supplied by contractor). Insure cuts are clean, straight and square.
2. Cleans ends of seal with a solvent to remove any foreign material.
3. Brush apply PP Primer to both seal ends to be joined together at splice.
4. Reassemble mitered ends of adjacent seals utilizing the reinforcing corner clips (for 90° transitions only).
5. Apply 241F adhesive as specified by the manufacturer to one of the two seal surfaces to be bonded.
6. Apply pressure bringing the two surfaces in tight contact immediately upon completing application of the
adhesive. Hold in place for approximately one to two minutes to allow adhesion.
7. Re-check quality of all miters or splices and apply additional adhesive if required to ensure proper miter or
splice.
8. Contact manufacturer for clarification of above procedure (if required) prior to proceeding with splicing visual
seal profile. It is usually recommended to allow 15 minutes time before installing spliced seal. Care shall be
excercised as a result that it takes 24 hours for adhesive to fully cure.
"WSW" Visual Seal Field Splice Procedures
Used for direction changes, Going around corners, Parapets, Etc
(Santoprene Only)
Horizontal Transition
Vertical Transition
ThermoPlastic
Visual Seal
Aluminum
Extrusion
Aluminum
Extrusion
Moisture Barrier
Seal
Moisture Barrier
Seal
Suggested Reinforcing
Corner Clips
NOTE: Clips available for
90° transititons only
Aron Alpha 241F Adhesive
(Prepare cut ends of seal with
PP Primer)
Installation procedure: W
SW
W
eatherS
eam
2 S
eal system
Sheet
7
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
Installation procedure: W
SW
W
eatherS
eam
3 S
eal system
Sheet
8
of 8
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
J:\M
AR
KE
TIN
G\M
ed
ia
\L
og
os S
ig
na
tu
re
s &
S
ym
bo
ls\L
og
os\A
pp
ro
ve
d_
WB
A_
Lo
go
s\Jp
eg
s\W
BA
B
lu
e.jp
g
"WSW" Termination Detail
Can be used at the base of the WSW Seal Installation
Expansion Joint System
Finished Wall
(By Others)
Wabo Weatherseam
(Field Fabricated By Others)
Termination Boot (Neoprene) Base of exterior wall
Drip edge
1'-4" (M
in)
8" (M
in)
1'-0" (M
in)
Varies
Varies (Note 1)
4" Min.4
"
M
i
n
.
V
a
r
i
e
s
(
N
o
t
e
1
)
8" (M
in)
4
"
= Fold Lines
= Cut Lines
Represents Contact points when
assembling drainage boot. The
Dots must be touching and
bonded for a proper assembly.
Material: 1/32" Thick Neoprene
Sheetgood. (WBA P/n: 6300)
Use Jeene Profile Glue to fold
and bond side flaps together.
Notes:
1. Overall width of Boot Transition will be determined on the amount of movement the
WSW system can accommodate during normal movement ranges. WBA suggests
that the dimension will be at least Maximum Opening plus 1". This is to ensure that
there will not be any damage to the boot while the system is at maximum opening.
Issued: 01/07/2019 p/n: 20207
Wabo® WeatherSeam
Model(s) "WSW 1600, 2000 & 2400"
Horizontal & Vertical Expansion Control Systems
The following installation procedure is very important and must be fully understood
prior to beginning any work. To ensure proper installation and performance of
expansion joint system the following actions must be completed by the installing
contractor. Failure to do so will affect product warranty.
Carefully read and understand installation procedure. Contact WBA's
Technical Service Department at (800) 677-4922 for product assistance.
Inspect all shipments and materials for missing or damaged components
and hardware. Contact Customer Service at (800) 677-4922 with WBA's
order number and invoice for prompt assistance.
Inspect substrate or adjacent construction for acceptance before
beginning work. Report unacceptable construction to the project manager
for scheduled repair work.
Review WBA shop drawings for project specific detailed information if
Engineering services were purchased at time of order.
1)
2)
3)
4)
Installation Procedure
Information provided herein, including but not limited to, any drawing, design, photograph, graphic, or statement(s) ("Materials") are proprietary and the property of Watson Bowman Acme Corporation ("Company"). Reproduction, translation, or
reduction to any electronic medium or machine readable form, in whole or part, is strictly prohibited, except for the express purpose for which it has been furnished, without prior written consent of Company. All Materials contained herein are
provided by Company for information purposes only. Company reserves the right to amend or withdraw any information contained in the Materials without notice. All technical or other advice by Company, whether verbal or written, concerning
products, or the use of products in specific situations ("Advice") is given by Company and is used at the Users own risk.
Watson Bowman Acme Corp. 95 Pineview Drive Amherst, NY 14228
phone: (716) 691-7566 fax: (716) 691-9239
website: www.wbacorp.com
Components shown below vary in size depending
on model of system
Standard Components
4"WSW-1600
"A"Model
Dimension Chart & Part Number
5"
1342
Part Number
1262
Wall Mount Aluminum Extrusion
(Exterior) (P/N - 1296)
Plastic Insert
(P/N - 5786)
1
4
" x 2
1
2
" Screw Anchor
(P/N - 5782)
*
"A"
6" 1362Elastomeric Visual Seal
(For Part Number Refer to Chart)
*
Optional Components for Splice Procedures. Place order for required Quantities
Moisture Barrier
(P/N - 1175)
1
4
" Dia x 2" Bolt
(P/N - 4837)
Aluminum Center Profile
(Interior) (P/N - 1294)
Aluminum Center Profile
(Exterior) (P/N - 1293)
Wall Mount Aluminum Extrusion
(Interior) (P/N - 1295)
#10-24 x
1
2
" Lg Csk. Screw
(P/N - 5573)
WSW-2000
WSW-2400
Pantagraph
(P/N - 15501)
Self-Centering Bar
(For Part Number Refer to Chart)
"B"
2'-8 3/8"WSW-1600
"B"Model
Dimension Chart & Part Number
3'-6 3/8"
15644
Part Number
15605
4'-2 3/8" 15641
WSW-2000
WSW-2400
Installation procedure: W
SW
W
eatherS
eam
4 S
eal system
Sheet
1
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
NP-1 Sealant
(P/N - 2826)
241F Adhesive
(P/N - 2716)
*
Butt Splice Plate
Aluminum (P/N - 8366)
*
90° Splice Plate
Aluminum (P/N - 8365)
*
90° Horiz. Splice Plate
Aluminum (P/N - 8364)
*
PP Primer
(P/N - 2717)
Horiz. to Vert. Splice Clip
Seal only (P/N: 1194)
*
*
Butt Splice Clip
Seal only (P/N: 1192)
*
Horiz. to Horiz.
Splice Clip
Seal only (P/N: 1193)
*
Prima-Lub
(P/N - 2720)
Flush Condition
- Apply continuous bead of NP-1 Sealant along back of the aluminum extrusions prior to installation.
(exterior only)
NP-1 Sealant
1/4
"
*
Joint Opening
Wall Mount
Aluminum Extrusion
- Field measure all lengths and directional changes for aluminum extrusions to ensure their proper
layout where required. Temporarily fix extrusions to wall surface in position as shown for field drilling
operations.
* Note: Always review architectural plans for specific project requirements
Note: Review entire procedure before beginning. If step 7 is not possible due to limited space
follow steps 5-7 first outside of joint opening, then do steps 1-4 and then install seals.
1
2
Installation procedure: W
SW
W
eatherS
eam
4 S
eal system
Sheet
2
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
- Field drill anchor holes at 18" O.C. (Max) along aluminum gauge line. Drill through aluminum into
adjacent construction on a 45° angle.
Note: All mortar joints in exterior walls must be flush with face of masonry to ensure tight weather seal.
1/4" Dia.
Screw Anchor
1/4
"
Joint Opening
3
4
5
°
Gauge Line
- Secure aluminum extrusions using appropriate anchors supplied by manufacturer.
Note: Utilize plastic inserts for securing Aluminum Extrusions to wall, if wall construction is either CMU
or a Masonary wall.
4
1/4
"
*
Joint Opening
Plastic Insert
3 1
/4
" @
E
xte
rio
r
2 3
/8
" @
In
te
rio
r
Installation procedure: W
SW
W
eatherS
eam
4 S
eal system
Sheet
3
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
3-1
/4
" @
E
xte
rio
r
2-3
/8
@
In
te
rio
r
5
1/4" Dia. x 2" Lg
Bolt
Pantagraph
6
- Adjust bolts in Pantographs to achieve dimension show and slide bolt head into Center Extrusion
cavity.
1 7
/1
6"
- Adjust 1/4" dia. Bolts on the Pantographs to achieve dimension show and thread the same size bolt
thru the Self-Centering Bar to achieve dimension shown.
1
7
16
"
3-1
/4
" @
E
xte
rio
r
2-3
/8
@
In
te
rio
r
Self-Centering Bar
1/4" Dia. x 2" Lg
Bolt
Center Extrusion
Installation procedure: W
SW
W
eatherS
eam
4 S
eal system
Sheet
4
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
7
- Set Center Extrusion with Pantographs and Self-Centering Bars into joint opening sliding the spheres
ends of the bars into the circular cavity of the edge Extrusions. Adjust bars to correct spacing (use
diagram top of page.) one at a time and drill in the #10 - 24 x 1/2" csk flat head self tapping screw into
the Center Extrusion bolt cavity below the bolt head at proper spacing to hold Pantographs and
Self-Centering Bars in place.
Note: If area to perform step 7 is limited refer to the general note on page 2 on optional method of
assembly.
- Adjust bolts in Pantographs and Self-Centering Bars to achieve dimension show and slide bolt head
into Center Extrusion cavity.
Note: See step 7 to view appropriate arrangement of Pantographs and Self-Centering Bars.
- Brush apply Prima-lub adhesive into extrusion cavity and install visual seals. Ensure full engagement
of the lug.
PantoGraph
Location Diagram Plan View
10' Standard Length
2'2'
3'-6"3'-6" 1'-6"1'-6"
8
Self-Centering Bar
PantoGraph
Prima-LubPrima-Lub
Locking LugLocking Lug
9
Locking Lug
Locking Lug
Prima-LubPrima-Lub
Moisture Barrier
Visual Seal
Installation procedure: W
SW
W
eatherS
eam
4 S
eal system
Sheet
5
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
Aluminum Wall Extrusion
1 1/2"
1 1/2"
1 1/2" 1 1/2"
Interior Extrusion Splice Details
Exterior Extrusion Splice Details
Splice Location
Splice Plate
SW Centering
Extrusion
90° Splice Plate
SW Centering
Extrusion
Horizontal to
Vertical Splice
Side Elevation
Horizontal to Horizontal Butt Splice
or
Vertical to Vertical But Splice
2"
2 1
/2
"
2 1/2"
Splice Plate
Horizontal to Horizontal 90° Splice
SW Centering
Extrusion
#10-24 x
3
8
" Round
Head Self-Tapping
Screw
1/2
"
1/4"
Horizontal to
Horizontal 90° Splice
Splice Plate
SW Centering
Extrusion
#10-24 x
3
8
" Round
Head Self-Tapping
Screw
1
2
"
Horizontal to Horizontal Butt Splice
or
Vertical to Vertical But Splice
Horizontal to
Vertical Splice
2 1
/2
"
2 1/2"
90° Splice Plate
SW Centering
Extrusion
Side Elevation
Splice Location
SW Centering
Extrusion
Splice Plate
2"
Installation procedure: W
SW
W
eatherS
eam
4 S
eal system
Sheet
6
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
1. Cut ends of the WSW visual seal, with a sharp knife, to the desired angle using a formed jig with miter box
(supplied by contractor). Insure cuts are clean, straight and square.
2. Cleans ends of seal with a solvent to remove any foreign material.
3. Brush apply PP Primer to both seal ends to be joined together at splice.
4. Reassemble mitered ends of adjacent seals utilizing the reinforcing corner clips (for 90° transitions only).
5. Apply 241F adhesive as specified by the manufacturer to one of the two seal surfaces to be bonded.
6. Apply pressure bringing the two surfaces in tight contact immediately upon completing application of the
adhesive. Hold in place for approximately one to two minutes to allow adhesion.
7. Re-check quality of all miters or splices and apply additional adhesive if required to ensure proper miter or
splice.
8. Contact manufacturer for clarification of above procedure (if required) prior to proceeding with splicing visual
seal profile. It is usually recommended to allow 15 minutes time before installing spliced seal. Care shall be
excercised as a result that it takes 24 hours for adhesive to fully cure.
"WSW" Visual Seal Field Splice Procedures
Used for direction changes, Going around corners, Parapets, Etc
(Santoprene Only)
Horizontal Transition
Vertical Transition
ThermoPlastic
Visual Seal
Aluminum
Extrusion
Aluminum
Extrusion
Vinyl Functional
Seal
Vinyl Functional
Seal
Suggested Reinforcing
Corner Clips
Note: Clips only available
for 90° transititons
Aron Alpha 241F Adhesive
(Prepare cut ends of seal with
PP Primer)
Installation procedure: W
SW
W
eatherS
eam
3 S
eal system
Sheet
7
of 7
In
fo
rm
atio
n p
ro
vid
ed
h
ere
in
, in
clu
din
g b
ut n
ot lim
ite
d to
, a
ny d
ra
win
g, d
esig
n, p
ho
to
gra
ph
, g
ra
ph
ic, o
r sta
te
me
nt(s) ("M
ate
ria
ls") a
re
p
ro
prie
ta
ry a
nd
th
e p
ro
pe
rty o
f W
atso
n B
ow
ma
n A
cm
e
Co
rp
ora
tio
n ("C
om
pa
ny"). R
ep
ro
du
ctio
n, tra
nsla
tio
n, o
r re
du
ctio
n to
a
ny e
le
ctro
nic m
ed
iu
m o
r m
ach
in
e re
ad
ab
le
fo
rm
, in
w
ho
le
o
r p
art, is strictly p
ro
hib
ite
d, e
xce
pt fo
r th
e e
xp
re
ss p
urp
ose
fo
r
wh
ich
it h
as b
ee
n fu
rn
ish
ed
, w
ith
ou
t p
rio
r w
ritte
n co
nse
nt o
f C
om
pa
ny. A
ll M
ate
ria
ls co
nta
in
ed
h
ere
in
a
re
p
ro
vid
ed
b
y C
om
pa
ny fo
r in
fo
rm
atio
n p
urp
ose
s o
nly. C
om
pa
ny re
se
rve
s th
e rig
ht to
am
en
d o
r w
ith
dra
w a
ny in
fo
rm
atio
n co
nta
in
ed
in
th
e M
ate
ria
ls w
ith
ou
t n
otice
. A
ll te
ch
nica
l o
r o
th
er a
dvice
b
y C
om
pa
ny, w
he
th
er ve
rb
al o
r w
ritte
n, co
nce
rn
in
g p
ro
du
cts, o
r th
e u
se
o
f p
ro
du
cts in
sp
ecific situ
atio
ns ("A
dvice
") is g
ive
n b
y C
om
pa
ny a
nd
is u
se
d a
t th
e U
se
rs o
wn
risk.
Watson B
ow
man A
cm
e C
orp.
95 P
ineview
D
rive A
mherst, N
Y 14228
phone: (716) 691-7566 fax: (716) 691-9239
we
bsite
: w
ww
.w
ba
co
rp
.co
m
