Installation Manual COLOR LCD SOUNDER FCV-295 · Observe the following compass safe distances to...

www.furuno.co.jp

All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

Installation ManualCOLOR LCD SOUNDER FCV-295

SAFETY INSTRUCTIONS ............................................................................ i

SYSTEM CONFIGURATION ...................................................................... iii

EQUIPMENT LISTS.................................................................................... iv

1. MOUNTING............................................................................................ 11.1 Display Unit ..................................................................................................................11.2 Transducer ...................................................................................................................21.3 Water Temperature/Speed Sensor ..............................................................................2

2. WIRING .................................................................................................. 52.1 Interconnection .............................................................................................................52.2 Cable Fabrication .........................................................................................................62.3 Input/Output Sentences................................................................................................8

3. INITIAL SETTING .................................................................................. 93.1 Language Setting .........................................................................................................93.2 Transducer Data.........................................................................................................103.3 Speed/Water Temperature Sensor Calibration ..........................................................133.4 NMEA Port Setting .....................................................................................................15

APPENDIX TRANSDUCER 82B-35R .................................................AP-1

PACKING LIST........................................................................................ A-1

OUTLINE DRAWINGS............................................................................. D-1

INTERCONNECTION DIAGRAM ............................................................ S-1

WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.

Warning, Caution Mandatory Action Prohibitive Action

SAFETY INSTRUCTIONSThe installer must read the applicable safety instructions before attempting to install the equipment.

WARNING WARNINGBe sure that the power supply iscompatible with the voltage rating of the equipment.

Connection of an incorrect power supply can cause fire or damage the equipment. The voltage rating of the equipment appears on the label above the power connector.

Install the transducer according to the installation instructions.

Failure to install the transducer correctly may result in water leakage and damage to the ship's hull.

For wooden or FRP vessel using a steel tank, attach a zinc plate to the hull to prevent electrolytic corrosion.

Electrolytic corrosion can, in the worst case, result in loss of the transducer.

Do not disassemble or modify theequipment.

Fire, electrical shock or serious injurycan result.

Turn off the power at the switchboardbefore beginning the installation. Connect to a dedicated breaker in the power distributor.

Fire or electrical shock can result if the power is left on.

Do not install the equipment where it may get wet from rain or water splash.

Water in the equipment can result in fire, electrical shock or damage the equipment.

Be sure no water leaks in at the trans-ducer mounting location.

Water leakage can sink the vessel. Also, confirm that the transducer will not loosen by ship's vibration. The installer of the equipment is solely responsible for the proper installation of the equipment.FURUNO will assume no responsibility for any damage associated with improperinstallation.

Use the proper cable and fuse.

Use of an incorrect cable and fuse can damage the equipment and can cause fire.

i

CAUTION

Observe the following compass safedistances to prevent interference to amagnetic compass:

Ground the equipment toprevent mutual interference.

Do not allow warm water or any otherliquid other than seawater or freshwater to contact the transducer.

The transducer may become damaged.

Do not turn on the power when the transducer is in air.

The transducer may become damaged.

Do not install the transducer wherenoise or air bubbles is present.

Performance will be affected.

CAUTIONThe transducer cable must be handled carefully, following the guidelines below.

• Keep fuels and oils away from thecable.

• Locate the cable where it will not be damaged.• The cable sheath is made of chloro- phrene or polychloride vinyl, which

are easily by damaged plastic solvents such as toulene. Locate the cable well away from plastic solvents.

Standardcompass

Steeringcompass

CV-295 0.80 m 0.50 m

ii

iii

SYSTEM CONFIGURATION

Basic configuration is shown with solid line.

High Freq. Low Freq.

TransducerTransducer

Navigator

Display unit

CV-295

12-24 VDC

Rectifier

PR-62

100/110/115/

220/230 VAC

1 , 50/60 Hz

Water temperature sensor

T-02MSB, etc.

Speed/temp sensor

ST-02MSB, etc.

iv

EQUIPMENT LISTS

Standard supply

Option

Name Type Code No. Qty Remarks

Display Unit CV-295 - 1

Spare Parts SP02-05501 001-032-740 1 setSee packing list at back of this manual.Accessories FP02-05700 000-011-976 1 set

Installation Materials CP02-08401 001-032-750 1 set

Name Type Code No. Remarks

Transducer See next several pages.

-

Thru-hull pipe -

Tank -

Cable MJ-A6SPF0003-050C 000-154-054-10 one end 6 pin, 5 m, for navigator

CO-SPEVV-SBC 2Px0.2SQ LF

000-111-680-10 5 m

000-120-792-10 10 m

000-120-793-10 15 m

Water temperature sensor

T-02MSB 000-040-040 Thru-hull type

T-02MTB 000-040-026 Transom type

T-03MSB 000-040-027 Thru-hull type

Speed/Tempera-ture sensor

ST-02MSB 000-137-986-01 Thru-hull type

ST-02PSB 000-137-987-01 Thru-hull type

Rectifier PR-62 000-013-484 100 V AC

000-013-485 110 V AC

000-013-486 220 V AC

000-013-487 230 V AC

v

Combination of transducer, thru-hull pipe and tankOutput

(W)Frequency

(kHz) Ship type Transducer Thru-hull pipe Tank

1k/1k 28/50 Steel 28F-850B-9B

TWB-6000(2) T-656FRP - -

28/88 Steel 28F-888B-8

TWB-6000(2) T-657FRP - -

50/88 Steel 50B-9B88B-8

TWB-6000(2) T-658FRP - -

50/200 Steel 50/200-1T50/200-1ST

TFB-5000(1) T-603FRP - T-603FSteel 50/200-12M - -FRP - -

1k/2k 28/200 Steel 28F-8200B-8/8B

TWB-6000(2) T-657FRP - -

50/200 Steel 50B-9B200B-8/8B

TWB-6000(2) T-658FRP - -

88/200 Steel 88B-8200B-8/8B

TWB-6000(2) T-659FRP - -

2k/2k 28/50 Steel 28F-1850B-12

TFB-7000(2) T-634FRP TRB-1100(2) T-634-F

28/82 Steel 28F-1882B-35R

TFB-7000(2) T-636FRP TRB-1100(2) T-636-F

28/88 Steel 28F-1888B-10

TFB-7000(2) T-636FRP TRB-1100(2) T-636-F

28/200 Steel 28F-18200B-8/8B

TFB-7000(2) T-638FRP TRB-1100(2) T-638-FSteel 28BL-6HR

200B-8/8BTFB-7000(2) T-693

FRP TRB-1100(2) T-693-F38/200 Steel 38BL-9HR

200B-8/8BTFB-7000(2) T-693

FRP TRB-1100(2) T-693-F50/82 Steel 50B-12

82B-35RTFB-7000(2) T-643

FRP TRB-1100(2) T-643-F50/88 Steel 50B-12

88B-10TFB-7000(2) T-643

FRP TRB-1100(2) T-643-F50/200 Steel 50B-12

200B-8/8BTFB-7000(2) T-645

FRP TRB-1100(2) T-645-FSteel 50BL-12HR

200B-8/8BTFB-7000(2) T-693

FRP TRB-1100(2) T-693-F50/200 Steel 50BL-12

200B-8/8BTFB-7000(2) T-693

FRP TRB-1100(2) T-693-F82/200 Steel 82B-35R

200B-8/8BTFB-7000(2) T-649

FRP TRB-1100(2) T-649-F88/200 Steel 88B-10

200B-8/8BTFB-7000(2) T-649

FRP TRB-1100(2) T-649-F

vi

2k/2k 28/107 Steel 28F-18100B-10R

TFB-7000(2) T-636FRP TRB-1100(2) T-636-F

2k/3k 28/150 Steel 28F-18150B-12H

TFB-7000(2) T-637FRP TRB-1100(2) T-637-F

50/107 Steel 50B-12100B-10R

TFB-7000(2) T-643FRP TRB-1100(2) T-643-F

50/150 Steel 50B-12150B-12H

TFB-7000(2) T-644FRP TRB-1100(2) T-644-F

3k/2k 68/200 Steel 68F-30H200B-8/8B

TFB-7000(2) T-647FRP TRB-1100(2) T-647-F

107/200 Steel 100B-10R200B-8/8B

TFB-7000(2) T-649FRP TRB-1100(2) T-649-F

3k/3k 28/38 Steel 28BL-12HR38BL-15HR

TFB-7000(2) T-681FRP TRB-1100(2) T-681-FSteel 28F-24H

38BL-15HRTFB-7000(2) T-681


50BL-24HRTFB-7000(2) T-681


50F-24HTFB-7000(2) T-681

FRP TRB-1100(2) T-681-FSteel 28F-24H

50BL-24HTFB-7000(2) T-696


50BL-24HRTFB-7000(2) T-681


50F-24HTFB-7000(2) T-681


88F-126HTFB-7000(2) T-682


88F-126HTFB-7000(2) T-682


150B-12HTFB-7000(2) T-683


150B-12HTFB-7000(2) T-683


200B-12HTFB-7000(2) T-683


200B-12HTFB-7000(2) T-683


50BL-24HRTFB-7000(2) T-681


50F-24HTFB-7000(2) T-681


88F-126HTFB-7000(2) T-682

FRP TRB-1100(2) T-682-F

Output(W)

Frequency(kHz) Ship type Transducer Thru-hull pipe Tank

vii

3k/3k 38/150 Steel 38BL-15HR150B-12H

TFB-7000(2) T-683FRP TRB-1100(2) T-683-F

38/200 Steel 38BL-15HR200B-12H

TFB-7000(2) T-683FRP TRB-1100(2) T-683-F

50/88 Steel 50BL-24H88F-126H

TFB-7000(2) T-697FRP TRB-1100(2) T-697-FSteel 50BL-24HR

88F-126HTFB-7000(2) T-682


88F-126HTFB-7000(2) T-682


150B-12HTFB-7000(2) T-683


150B-12HTFB-7000(2) T-683

FRP TRB-1100(2) T-683-F50/200 Steel 50BL-24H

200B-12HTFB-7000(2) T-695


200B-12HTFB-7000(2) T-683


200B-12HTFB-7000(2) T-683

FRP TRB-1100(2) T-683-F68/150 Steel 68F-30H

150B-12HTFB-7000(2) T-646


200B-12HTFB-7000(2) T-646


150B-12HTFB-7000(2) T-685


200B-12HTFB-7000(2) T-685

FRP TRB-1100(2) T-685-F1k 28 Steel 28F-8 TFB-5000(1) T-604

FRP TRB-1000(1) T-604-F50 Steel 50B-6/6B TFB-5000(1) T-605

FRP TRB-1000(1) T-605-FSteel 50B-9B TFB-5000(1) T-603FRP TRB-1000(1) T-603-F

68 Steel 68F-8H TFB-5000(1) T-621FRP TRB-1000(1) T-621-F

88 Steel 88B-8 TFB-5000(1) T-606FRP TRB-1000(1) T-606-F

200 Steel 200B-5S TFB-5000(1) T-605FRP TRB-1000(1) T-605-F

2k 28 Steel 28F-18 TFB-5000(1) T-612FRP TRB-1000(1) T-612-FSteel 28BL-6HR TFB-5000(1) T-702FRP TRB-1000(1) T-702-F

Output(W)


viii

2k 38 Steel 38BL-9HR TFB-5000(1) T-702FRP TRB-1000(1) T-702-F

50 Steel 50B-12 TFB-5000(1) T-611FRP TRB-1000(1) T-611-FSteel 50BL-12 TFB-5000(1) T-702FRP TRB-1000(1) T-702-FSteel 50BL-12HR TFB-5000(1) T-702FRP TRB-1000(1) T-702-F

82 Steel 82B-35R TFB-5000(1) T-609FRP TRB-1000(1) T-609-F

88 Steel 88B-10 TFB-5000(1) T-609FRP TRB-1000(1) T-609-F

200 Steel 200B-8/8B TFB-5000(1) T-608FRP TRB-1000(1) T-608-F

3k 28 Steel 28F-24H TFB-4000(1) T-616FRP TRB-1000(1) T-616-FSteel 28BL-12HR TFB-4000(1) T-616FRP TRB-1000(1) T-616-F

38 Steel 38BL-15HR TFB-4000(1) T-616FRP TRB-1000(1) T-616-F

50 Steel 50F-24H TFB-4000(1) T-616FRP TRB-1000(1) T-616-FSteel 50BL-24HR TFB-4000(1) T-616FRP TRB-1000(1) T-616-FSteel 50BL-24H TFB-4000(1) T-694FRP TRB-1000(1) T-694-F



107 Steel 100B-10R TFB-5000(1) T-609FRP TRB-1000(1) T-609-F

150 Steel 150B-12H TFB-5000(1) T-615FRP TRB-1000(1) T-615-F

200 Steel 200B-12H TFB-5000(1) T-615FRP TRB-1000(1) T-615-F

Output(W)


1

1. MOUNTING

1.1 Display Unit

Mounting considerations• Locate the unit out of direct sunlight.• Select a location where the display screen can be easily observed while operating the control

panel.• Leave sufficient space around the unit for maintenance and servicing. Recommended mainte-

nance space appears in the outline drawings at the back of this manual.• Observe the compass safe distances on page ii to prevent deviation of a magnetic compass.The display unit can be mounted on the tabletop or on the panel (flush mounting). Mount the unit, referring to the outline drawings at the back of this manual.

The power cable is connected to the terminal board in the display unit. Therefore the power cable can not be disconnected easily like a connector. So connect the cable to a dedicated breaker in the power distributor in the ship.

NOTICEDo not apply paint, anti-corrosive sealantor contact spray to coating or plastic parts of the equipment.

Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors.

WARNINGTurn off the power at the switchboardbefore beginning the installation. Connect to a dedicated breaker in the power distributor.

Fire or electrical shock can result if the power is left on.

2

1.2 TransducerThe performance of the echo sounder depends upon the transducer position. A place least affect-ed by air bubbles should be selected since turbulence blocks the sounding path. Further, select a place least influenced by engine noise. It is known that air bubbles are fewest at the place where the bow first falls and the next wave rises, at usual cruising speed.

Note: The face of the transducer must be facing the sea bottom in normal cruising trim of the boat.

1.3 Water Temperature/Speed Sensor

Transom mount water temperature sensor T-02MTB• Fix the cable at a convenient location on the transom with the cable clamp.• When the cable is led through the transom board, make a hole of approx. 17 mm in diameter to

pass the connector. After passing the cable, seal the hole with a sealing compound.

How to mount transom mount water temperature sensor T-02MTB

D>500 D

5x20

Flush with hull bottom

[Units: mm]

70

35

3

Thru-hull mount water temperature sensor T-02MSB, T-03MSBSelect a suitable mounting location considering the following points:

• Select a mid boat flat position. The sensor does not have to be installed perfectly perpendicu-lar; however, the location should not be such that the transducer may be damaged when the boat is dry-docked.

• Locate away from equipment which gives off heat.• Locate away from drain pipes.• Select a location where vibration is minimal.

Assembling thru-hull water temperature sensor T-02MSB, T-03MSB

Cable8 m

Locknut

Coat withsealant.

Plate thick-ness within25 mm

Coat withsealant.

φ21 mm

φ25 mm

Washer

GasketLocknut

Locknut

Washer

Gasket

Holder Guide

Sensor Holder

T-02MSB T-03MSB

Mounting procedure1. Drill a hole of 21 mm in diameter in the mounting location.2. Pass the sensor cable through the hole.3. Pass gasket, washer and locknut onto cable in that order.4. Coat the sensor flange with high quality sealant and then fasten the sensor with the locknut. (Torque: max. 59N·m)5. Launch the boat to check for water leakage around the sensor.

Mounting procedure1. Drill a hole of 25 mm in diameter in the mounting location.2. Coat holder guide with high quality sealant, and pass gasket, washer and locknut onto holder guide in that order and then tighten the locknut.3. Set the sensor holder to the holder guide from inside the boat and then tighten the locknut. 4. Launch the boat to check for water leakage around the sensor.

φ42

70

M20

Cable8 m

4

Through-hull mount water temperature/speed sensor ST-02MSB, ST02-PSBSelect a suitable mounting location considering the following:

• Select a mid-boat flat position. The sensor does not have to be installed perfectly perpendicu-lar. The sensor must not be located where it might get damaged in dry-docking operation.

• Select a place apart from equipment generating heat.• Select a place in the forward direction viewing from the drain hole, to allow for circulation of

cooling water.• Select a place free from vibration.

1. Dry-dock the boat.2. Make a hole of approx. 51 mm diameter.3. Unfasten locknut and remove the flange of the sensor.4. Apply high-grade sealant to the flange of the sensor.5. Pass the sensor casing through the hole.6. Face the notch on the sensor toward boat's bow and tighten the flange.7. Set the sensor section to the sensor casing and tighten the locknut.8. Launch the boat and check for water leakage around the sensor.

Water temperature/speed sensor ST-02MSB, ST-02PSB

Locknut

123

Face "notch"toward bow.

Flange nut

Coat withsilicone sealant.

51

Brimφ77

2. WIRING

2.1 InterconnectionRefer to the interconnection diagram at the back of this manual for detailed information.

Wiring diagram for FCV-295

Low

TransducerSpeed/Water temperaturesensor

Navigator

12-24 VDC

DP

YC

Y-1

.5

DP

YC

Y-1

.5

Rectifier

PR-62

100/110/115/

220/230 VAC

1φ, 50/60 Hz

*Transducer *

*: This unit cannot accept transducers of

53 to 65 kHz, 111 to 139 kHz and 171

to 183 kHz.

IV-2.0sq

Display unit rear panel

(connector cover removed)

High

MJ-A

6S

PF

00

03

-05

0C

(Connect to a dedicated breaker in the power distributor.)

Grounding wire:

As short as possible

5

2.2 Cable Fabrication

Power cableThis echo sounder is designed to be powered with 12-24 VDC. Use the cable DPYCY-1.5 (Japan Industry Standard) or equivalent.

Transducer cableSeparate the transducer cable well away from power cables to prevent interference. Connect the cable to the transducer port (for high frequency and/or low frequency) at the rear of the display unit. Fabricate the cable as below.

Approx. 70 3

ArmorSheath

Vinyl tape

6

Clamp armor with cable clamp.

Crimp-on lug

FV2-M4

30

Sheath

ConductorS = 1.5 mm

= 1.56 mm(AWG16)

2

DPYCY-1.5

Armor

Sheath

= 13.7 mm

Shield

Vinyl tape

Sheath

Wrap shield around sheath 30 mm and cut

excess shield. Clamp here with cable clamp.

Extract cores from here and cut inner materials.

Approx. 100

Attach WAGO

connector.

(See next page.)

[Composite transducer]

BLK, RED: L side

BLU, GRN: H side

Note: Never connect the shield to #2 of

the WAGO connector.

Shield

306Vinyl tape

6

7

WAGO connector (for transducer and NMEA ports)

NMEA portConnect a GPS navigator, etc. to NMEA port J2 #1 to #4. You can connect two sensors (for ex-ample, GPS receiver GP-310B and smart sensor). One connects to NMEA port J2 #1 to #2 and the other connects to the NMEA port J2 #3 to #4.

1. Twist conductors.2. Insert opener and press it down.3. Insert core to hole.4. Release opener.5. Pull the core to confirm that it is tightly fastened.

Opener (big one: for transducer port small one: for NMEA port)

CoreTwist.

Press

Wind vinyl tape on sheath.306

Wrap shield about three turns

and cut excess shield.

Wind vinyl tape

on edge of shield.Solder vinyl wire

to shield.

Extract cores from here and

cut inner materials.

Clamp this parts.Attach WAGO connector.

Approx. 90Sheath

Shield

Vinyl tape

2.3 Input/Output Sentences

Input sentences

Output sentences

Sentence Data RemarksBWC Range/bearing to waypointGGA Time, position GPS positionGLC GRI, Time difference Loran CGLL Latitude and longitude GPS positionGNS GNSS position fixingGTD Time difference Loran CHDG Ship's heading, deviation, variationHDT True headingMDA Weather informationMTW Water temperatureMWV Wind direction, wind speed (true or apparent)RMA Latitude and longitude, TD, ground speed and course Loran CRMB Recommended minimum navigation informationRMC Latitude and longitude, speed over ground and course over ground GPSVHW True/magnetic bearing, speed through waterVTG Speed over ground and course over groundXTE Cross track error

Sentence Data Remarks

DBT Depth below transducer Ver. 1.5

DPT Depth below transducer and offset Ver. 2.0

MTW Water temperature With connection of water temperature sensor

TLL Marker line position Ver. 2.0

SDmrk Mark position (L&L) and its additional data

VHW Speed thru water

RMB Navigation information Ver. 1.5

DBS Depth below sea surface

8

3. INITIAL SETTING

This chapter provides the information necessary for initial setup of the equipment. First turn on the power and set display language. Then, set transducer used, by model number (FURUNO trans-ducer only) or by specifications.

3.1 Language Setting1. Press [ /BRILL] key to turn on the power. The following display appears.

Language setting screen

2. Press or to select a desired language, and then press the ENTER key to set. The units setting screen appears.

Unit setting screen

3. Set the units of measurement if necessary. For example, to set the distance unit, press to select "Distance Unit" and press the ENTER key. The list of selectable distance units is dis-played.

9

4. Press or to select necessary unit and then press the ENTER key to set.• Depth: m, ft, fa, pb, HR (Japanese unit)• Temp: °C, °F• Speed: kt, km/h, mph• Wind: kt, km/h, mph, m/h• Distance: nm, km, sm

5. Press the MENU key. The following message appears.

6. Press any key. The transducer setting screen appears. Proceed to next section.

3.2 Transducer Data

Entering transducer data by transducer modelThe following table shows the transducers programmed in the FCV-295.

Type Output (kW) Tap Type Output (kW) Tap28F-8 1 B 50BL-24HR 3 D

28BL-6HR 2 A 50F-24H 3 B

28F-18 2 B 68F-8H 1 A

28BL-12HR 3 A 68F-30H 3 B

28F-24H 3 D 82B-35R 2 E

38BL-9HR 2 B 88B-8 1 D

38BL-15HR 3 D 88B-10 2 C

50B-6B 1 A 88F-126H 3 E

50/200-IT (50 kHz) 1 B 100B-10R 3 E

50/200-1ST (50 kHz) 1 B 150B-12H 3 C

50B-9B 1 A 200B-5S 1 D

50B-12 2 A 50/200-1T (200 kHz) 1 C

50BL-12 2 A 50/200-1ST (200 kHz) 1 A

50BL-12HR 2 B 200B-8B 2 C

50BL-24H 3 D 200B-12H 3 C

CAUTIONSet the transducer model numberproperly.

Wrong transducer setting can damage the transducer and void the warranty.

10

1. At the transducer setting screen, confirm that "XDCR Select" is set to "XDCR Type" (default setting).

Transducer setting screen

2. If a high frequency transducer is fitted, press to select "HF Connection" and then press the ENTER key.

3. Press to select "Connected" and then press the ENTER key.4. Press to select "Freq" and then press the ENTER key.

5. Press or to select the transducer frequency and then press the ENTER key.

ConnectedNot connected

11

6. Press to select "Transducer" and then press the ENTER key. The list of programmed trans-ducers appears.

7. Press to select transducer connected and then press the ENTER key.8. Jot down the alphabet which appears on the "Tap" line. You may need to change the tap set-

ting at the rear of the display unit depending on the transducer type which is connected. For details, see below.

9. If a low frequency transducer is fitted, repeat steps 2 to 8.Note: Leave the "Tx Power" setting at "Auto".

10.Press and hold down the [ /BRILL] key to turn off the power.

Note: To confirm the transducer selection after completion of the setting, turn on the power while pressing any key. Release the key after the “XDCR Setting” dialog box appears.

Tap settingSet the tap according to the alphabet shown when you selected transducer type.

200B-5S50/200-1T50/200-1ST200B-8B200B-12H (Example: 200 kHz)

Display unit rear panel(connector cover removed)

Tap setting plug(for high frequency)

E D C B A

Common point

Tap setting plug(for low frequency)

Set this end in applicable slot according toalphabet indication.

jumper connection

12

Entering transducer data by transducer specificationsTo connect the transducers which are not programmed, do as follows:

Note: The transducers of 53 - 65 kHz, 111 to 139 kHz and 171 - 183 kHz cannot be connected to the FCV-295 because of noise.

1. At the XDCR Setting dialog box, select "XDCR Select" and press the ENTER key.The following screen appears.

2. Press to select "Manual", and then press the ENTER key.3. If a high frequency transducer is fitted, press to select "HF Connection" and then press the

ENTER key.

4. Press to select "Connected" and then press the ENTER key.5. Press to select "Freq" and then press the ENTER key.

6. Press or to set the frequency of the transducer which is connected and then press the ENTER key.

7. Press to select "Band width" and then press the ENTER key.8. Press or to set the value for the bandwidth and then press the ENTER key. If the band-

width is not entered manually, it is automatically set to 1/10 of the transducer frequency.9. If a low frequency transducer is fitted, repeat steps 3 to 8.

Note: Leave the "Tx Power" at "Auto".

10.Press and hold down the [ /BRILL] key to turn off the power.

3.3 Speed/Water Temperature Sensor CalibrationIf the optional speed and/or water temperature sensor is connected, set it up as follows:

1. Turn on the power and press the MENU key.The main menu and sub-menu appear.

2. Press to select "System" and "Calib" and then press the ENTER key.

XDCR Type

Manual

ConnectedNot connected

--- kHz

13

3. Press to select "Temp" and then press the ENTER key.

Temperature calibration screen

4. Press or to set the value for the temperature calibration and then press the ENTER key. For example, if the temperature indication is 2.5°C higher than the actual value,

set “-2.5°C”.5. To calibrate the speed value, press to select "Speed(STW)" and then press the ENTER key.

6. Press or to set the value for the speed calibration and then press the ENTER key.For example, if the speed indication is 5% lower than the actual value, set +5%.

7. To close the menu, press the MENU/ESC key twice.

14

3.4 NMEA Port SettingIf a GPS navigator and/or other sensor are connected, set up as follows.

1. Press the MENU key.2. Press to select "System" and "NMEA" and then press the ENTER key.

NMEA setting menu

3.Press to select the item to set and then press the ENTER key.

4.Press or to select an appropriate one and then press the ENTER key.

Description for each item of the NMEA menu

NMEA0183: Choose NMEA0183 version of navigation equipment connected to the NMEA port, among Ver. 1.5, Ver. 2.0 or Ver. 3.0. "SPECIAL" is for use with a navigator whose baud rate is 600 bps.

NMEA Port: The NMEA terminals in the NMEA port can function as input ports or input/output port. Change the setting to "In/In" when connecting GP-310B/320B/330B and a wind sensor. When connecting the GP-320B/330B and a wind sensor, first turn on "WAAS Setup" and then se-lect "In/In" as the NMEA Port setting.

• In/Out: NMEA port J2 #1 & #2 is output port and J2 #3 & #4 is input port.• In/In: NMEA port J2 #1 & #2 changes to input port. (Available with connection of the GP-310B/

320B/330B and a wind sensor.)NMEA Output: Set the output data sentences.

• Off: Outputs the "output data sentences" created in the FCV-295 (see page 8).• On: Outputs the "output data sentences" of FCV-295 and sentences which are input from other

equipment.

15

WAAS Setup: Choose how to use the WAAS signal when connecting with a WAAS capable GPS receiver, for example GP-320B/330B. The message types (WAAS-00 to WAAS-27) are used as WAAS correction. Choose WAAS-00 to enable WAAS.

TLL Output: Output the position selected by the MARK key to the plotter connected.

• Off: Does not output latitude/longitude.• TLL: Outputs latitude/longitude.• FURUNO-TLL: Outputs latitude/longitude, depth and water temperature. This requires

FURUNO-TLL enabled device.Port Monitor: Port Monitor provides information for the data sentences input from the NMEA port. Press the ENTER key to display the latest data sentence information. To display this information on the Port 2 screen when two sensors are connected, set NMEA Port on the NMEA menu to In/In. To terminate the port monitor, select "Exit" and press the ENTER key. And then, select Yes and press the ENTER key.

16

APPENDIX TRANSDUCER 82B-35R

The 82B-35R is a transducer with wide bandwidth of 65 kHz-110 kHz. It is constructed to provide protection against slamming.

Transducer, thru-hull pipe and tank list

Connection

Connect the 82B-35R transducer to either the "HF" or "LF" connector, referring to page S-1.

Tap Setting

Referring to page 12, set the tap to E.

Frquency (kHz)

Transducer Hull Material

Tank(Code No.)

Fasten inside hull (Code No.)

Fasten outside hull (Code No.)

15/88 15F-4S/82B-35R Steel T-628(000-015-921)

TWB-6000 (2)(000-015-207)

-

FRP T-628-F(000-015-922)

TRB-1100 (2)(000-015-218)

-

15F-10/82B-35R Steel T-629(000-015-804)

TWB-6000 (2)(000-015-207)

TFB-7000 (2)(000-015-209)

FRP T-629-F(270-601-660)

TRB-1100 (2)(000-015-218)

-

28/88 28F-18/82B-35R Steel T-636(000-015-813)

TWB-6000 (2)(000-015-207)

TFB-7000 (2)(000-015-209)

FRP T-636F(000-015-814)

TRB-1100 (2)(000-015-218)

-

50/88 50F-8G/82B-35R Steel T-636(000-015-813)

TWB-6000 (2)(000-015-207)

TFB-7000 (2)(000-015-209)

FRP T-636F(000-015-814)

TRB-1100 (2)(000-015-218)

-

50B-12/82B-35R Steel T-643(000-015-821)

TWB-6000 (2)(000-015-207)

TFB-7000 (2)(000-015-209)

FRP T-643F(000-015-822)

TRB-1100 (2)(000-015-218)

-

88/200 82B-35R/200B-8/200B-8B/200B-8N

Steel T-649(000-015-833)

TWB-6000 (2)(000-015-207)

TFB-7000 (2)(000-015-209)

FRP T-649F(000-015-834)

TRB-1100 (2)(000-015-218)

-

AP-1

Setting for dual frequency transmitting

1. Set the XDCR SELECT menu as follows (see page 11 and 12).

2. Press the [PWR] key to turn the power off, and turn it on again.3. Press the MENU key to show the menu.4. Select the [Sounder] and press the ENTER key.5. See the section "1.19.1 Sounder menu" in the Operator's Manual for how to set "Freq Choice"

and "Freq Control" for high and low frequencies.

Setting for “HF” connection Setting for “LH” connection

AP-2

NAME

OUTLINE

Q'TY

DESCRIPTION/CODE №

ＰＡ

ＣＫ

ＩＮＧ

　Ｌ

ＩＳＴ

02GE-X-9851-1

FCV-295-J/E

1/1

NAME

OUTLINE

Q'TY

DESCRIPTION/CODE №

ユニ

ット

UNIT

指示器

DISPLAY UNIT

1

**

CV-295

000-011-835-00

予備

品SPARE PARTS

SP02

-0550

1

ﾋｭｰｽﾞ

FUSE GLASS TUBE TYPE

4FGMB 125V 6A PBF

000-157-492-10

付属

品ACCESSORIES

FP02

-0570

0

ﾌｨﾙﾀｰｸﾘｰﾅｰ

LCD CLEANING CLOTH

102-155-1082-1

100-332-651-10

工事

材料

INSTALLATION MATERIALS

CP02

-0840

1

Fﾏｳﾝﾄﾖｳｽﾎﾟﾝｼﾞ

FLUSH MOUNTING SPONGE

102-160-1201-0

100-344-030-10

+ﾄﾗｽﾀｯﾋﾟ

ﾝﾈｼﾞ　1ｼ

ｭ

SELF-TAPPING SCREW

45X20 SUS304

000-162-608-10

操作ﾚﾊﾞｰ

TERMINAL OPENER

1231-131

000-165-800-10

圧着端

子

CRIMP-ON LUG

2FV2-M4

000-157-229-10

操作ﾚﾊﾞｰ

TERMINAL OPENER

1734-230

000-147-417-10

図書

DOCUMENT

操作要

領書（ﾀｹﾞﾝ）

OPERATOR'S MANUAL (MLG)

1MLG-23760-*

000-168-515-1*

装備要

領書

INSTALLATION MANUAL

1

**

IM*-23760-*

000-168-513-1*

取扱説

明書

OPERATOR'S MANUAL

1

**

OM*-23760-*

000-167-100-1*

ﾌﾗｯｼｭﾏｳﾝﾄ型

紙

FLUSH MOUNTING TEMPLATE

1C22-00703-* ﾜ/ｴｲ

000-168-518-1*

ｺ-ﾄﾞ

番号

末尾

の[*

*]は

、選

択品

の代

表ｺｰ

ﾄﾞを

表し

ます

。

CO

DE N

UM

BER

EN

DIN

G W

ITH

"**" IN

DIC

ATES T

HE C

OD

E N

UM

BER

OF R

EP

RESEN

TA

TIV

E M

ATER

IAL.

（略

図の

寸法

は、

参考

値で

す。

DIM

EN

SIO

NS IN

DR

AW

ING

FO

R R

EFER

EN

CE O

NLY.）

02GE-X-9851

型式

/ｺｰ

ﾄﾞ番

号が

２段

の場

合、

下段

より

上段

に代

わる

過渡

期品

であ

り、

どち

らか

が入

って

いま

す。

　な

お、

品質

は変

わり

ませ

ん。

TW

O T

YP

ES

AN

D C

OD

ES

MA

Y B

E L

ISTED

FO

R A

N ITEM

. T

HE L

OW

ER

PR

OD

UC

T M

AY B

E S

HIP

PED

IN

PLA

CE O

F

TH

E U

PP

ER

PR

OD

UC

T. Q

UA

LIT

Y IS

TH

E S

AM

E.

emiyoshi

テキストボックス

A-1

Nov.12'07 R.Esumi

emiyoshi


D-1

Nov.12'07 R.Esumi

emiyoshi


D-2

24

3

A

1

B CDRAWN

CHECKED

APPROVED

DWG.No.

TITLE

NAME

名称

INT

ERCO

NNEC

TION

DIA

GRAM

相互

結線

図

カラ

ー魚

群探

知機

COL

ORLCD

SOU

NDER

FCV

-295

T.YAMASAKI

T.TAKENO

REF.No.

SCALE

MASS

NOTE

*1:

SHIPYARD

SUPPLY.

*2:

OPTION.

*3:

CONNECTOR

PLUGFITTEDATFACTORY.

注記

＊１）造船所

手配。

＊２）オプシ

ョン。

＊３）コネク

タは工

場にて

取付

済み

。

*4:

CONNECT

THE82B-35RTRANSDUCERTOEITHERHFOR

LF.

C2376-C01-D

BLUGRNBLKRED

アオ

クロアカ

10m(1ST:15m) 50/200-1T

50/200-1ST

ﾐﾄﾞﾘ

TRANSDUCER

送受

波器

1

3

J4

2

1

32

J5

*2

NC

NC

TD_HF-H

TD_HF-L

TD_LF-H

TD_LF-L

NMEA

NMEA1_TD-A

NMEA1_TD-B

NMEA1_RD-A

NMEA1_RD-B

12V_P

12V_0V

7 8 9 105 64321J2 SHIELD

SHIELD

MJ-A6SPF

*3

MJ-A6SPF0003,5m,φ6*2

P P

5 64321

ETC.

NAVEQUIPMENT

航法装

置など

HIGH

LOW

TRANSDUCER

送受波器

NC

NC

シロ

クロ

WHT

BLK

キﾐﾄﾞﾘYEL

GRN

1B2

02P6350

1 2

TB1

(-)12-24VDC

(+)

5 6 3

IV-2sq.*1

21DPYC-1.5*1

DPYC-1.5

*1

12-24

VDC

100/110/115/

220/230VAC,

1φ

,50/60Hz

(-)

(+)

*2

RECTIFIER

整流

器

PR-62

水温

セン

サー

TEMP.SENSOR

8m

1 2 3 4 5 6

MJ-A6SPF P P

*3

J3

TEMP/SPEED

SENSOR

水温・速度

セン

サー

10m

TEMP

02P6349

1B1

SHIELD

TEMP

SPEED

+12V NC

TEMP_SPEED_0V

*2

*2

T-02MSB

T-03MSB

T-02MTB

ST-02MSB

ST-02PSB

パソ

コン

（保守

用）

PC

FORMAINTENANCE

1 2 3 4

J5

USB

USB

CABLE

VBUS

D-

D+

GND

USB

CV-295

DISPLAY

UNIT

指示器

*4

02-160-1001-1

1

3NC 2

J5

1

3

J4

NC 2

HF

LF

*1

IV-2sq.

アカRED

BLK クロ

アカRED

BLK クロ

TD_HF-L

TD_HF-H

TD_LF-L

TD_LF-H

16/Apr/09

16/Apr/09

TD-A

TD-B

NAV1

21J2 TD-A(RD-A)

TD-B(RD-B)

P

TWO

SETSCONNECTION(CHANGESETTINGFROM

MENU)

２台

接続

の場

合（

メニ

ュー

にて

設定

変更

）

TD-A

TD-B

NAV2

43RD-A

RD-B

P

7SHIELD

＊４）送受波

器82B-35RはHF/LFのい

ずれ

かに

接続。

9/Jun/09 R.Esumi

emiyoshi


S-1

The paper used in this manualis elemental chlorine free.

・FURUNO Authorized Distributor/Dealer

9-52 Ashihara-cho,Nishinomiya, 662-8580, JAPAN

Telephone : +81-(0)798-65-2111

Fax : +81-(0)798-65-4200

A : APR 2008.Printed in JapanAll rights reserved.

B : OCT . 05, 2009Pub. No. IME-23760-B

*00016851411**00016851411*(TATA ) FCV-295*00016851411**00016851411** 0 0 0 1 6 8 5 1 4 1 1 *

Installation Manual COLOR LCD SOUNDER FCV-295 · Observe the following compass safe distances to...

Documents

Transcript of Installation Manual COLOR LCD SOUNDER FCV-295 · Observe the following compass safe distances to...