Thank you for selecting the Crane Plumbing Fountain. To insure this product is installed properly, please read these instructionscarefully before you begin. This high quality, vitreous china fixture is meant to provide many years of service, but can bedamaged by improper handling and/or installation. Be sure your installation conforms to local codes.

INSTALLATION INSTRUCTIONSWATER FOUNTAINS AND CUSPIDOR

Unpack the fountain.Take a moment to check the fixtureto make sure there is no damage. Verify that you haveall the necessary tools, fittings, and connection hardwareto complete the installation.

1

PRE INSTALLATION

6523 NEU-WATERFALL INSTALLATION

FinishedWall

13”

2 x 6 Reinforcement

10”5” Typical Reinforcment

C-L Hanger

35”8

5”65”8

[168][93] [127]

[254]

[330]

[150]7”85

3”8 [10] I.P.S

Supply

23”4

[70]

Wall Screw

11”4

[32] I.P.S.WASTE

10 3”[264]8

33”[86]8

30 [762](For Grade Schools)

36 [914] - 44 [1118](To Suit Other Buildings)

FinishedFloor

Note on the diagram the location of water supply and waste pipe. These must be installed before the fountainis placed on the hanger.

The fountain bubbler fitting should be installed on thefountain before it is fastened to the wall. Waste assemblywith “P” trap is installed on unit. Make water supply andwaste connections after fountain has been installed.

The fountain is heavy. Provide suitable structural supportbehind the finished wall for the hanger lag screws.

The wall, or whatever material the screws areattached to, must be of sufficient strength to fullysupport the lavatory.

It may be necessary to install a 2 x 6 board behind thefinished wall. Position the board between two studs sothe front surface of the board is flush with the front ofthe studs. The finished wall is then applied over theboard.

Study the product diagram of the fountain(Figure 1). The metal hanger (included) is fastened tothe reinforcement with a lag screw. The fountain issupported by this hanger as primary support. A wallscrew must be installed through the hole in the lowersection of the fountain to secure it to the wall.

2

BUBBLER / PUSH BUTTON INSTALLATION

Note on the diagram the location of water supply and waste pipe. These must be installed before the fountainis placed on the hanger.

The fountain bubbler fitting should be installed on thefountain before it is fastened to the wall. Waste assemblywith “P” trap is installed on unit. Make water supply andwaste connections after fountain has been installed.

Bullet Head Bubblerwith 1/4” NPT-F Inlet

1/4” NPT Nipple 4” Long

PlatedWasherBrass

Nut

FemaleConnector

1/4” CopperTubing 10” Long

PushButtonAssembly

PushButtonBody

BrassNut Cartridge

1/4” CopperTubing 10” Long

“Y” Strainer

The Bubbler / Push Button assembly installs as shown in Figure 2. Caution: Do Not overtighten the brassnuts to avoid cracking the china.

Trim copper tubing as required. Water supply connectsto the “Y” strainer. This part acts as a pressure regulatorfor the bubbler assembly.

1

2 The waste “P” Trap assembly is factory installed. Make drain connection to the I.P.S waste.

Turn on water and check for leaks. Install stainless steelcover plate to cover the access opening.

Caulk along gap between fountain and finished wall tocomplete the installation.

Figure 2

Figure 1

Install screw into wall tosecure fountain to wall. Donot over-tighten screw toavoid cracking china.

1

Hanger

1

2

4

3

5

6

7

8

9

10

11

12

13

1

6615 COMBINATION INSTALLATION

Study the product diagram in Figure 3. Note the location of the reinforcing at the top and bottom ofthe opening. It may be necessary to install woodreinforcement in these areas to provide a solid attachment surface for the mounting screws.

These fixtures are heavy. Provide suitable structural support behind the finished wall for the mountingscrews provided.

The wall, or whatever structure the assembly isinstalled into must be of sufficent strength to fullysupport the fountain and cuspidor.

2

21”2 [64]

41”2 [114]

FinishedWall

13”8

[35]

7”8

[505]19

1”4

[57]2

1”4 [83]3

[139]21”5

4 Tailpiece[32]1”

FinishedFloor

5”83 [92]

3”8 [10] Dia. Hole

For Mounting

3”87 [188]

1”21 [38]

21 ”2

[64]

41”4 [108]

83 ”[10] Dia. Hole for Mounting

121”2 [311]

33”8 [86]

[381]15”

7”81 [48]

Finished Wall

5”811 [295]

10”[254]

[311]41”12

265 ”8 [676]

1 ”8

[130]5

1”41 [32] Tailpiece

Wall Opening

1”[25]

3 ”8 [10] Mounting Hole

Reinforcement

23”[584]

Reinforcing1”132 [343]

167”4 [113]

3”87 [187]

Note: Provide utility space or corridor access to fountain.

30 [762](For Grade Schools)

36 [914] - 44 [1118]

23”[584]

1”[25]

73”8

[187]Rim ofWare

131”2 [343]

Wall Openingfor Fountain

and Cuspidor

Mounting Hole

Study the product diagram in Figure 3. Note the location of the reinforcing at the top and bottom ofthe opening. It may be necessary to install woodreinforcement in these areas to provide a solid attachment surface for the mounting screws.

Note the location of the water supply and waste lines. These connectoins must be installed before the fixturesare placed in the openings. The units are shipped withthe bubbler and drain fittings but these fittings must beinstalled. Much of the bubbler and push button assemblycan be installed before the unit(s) are in place. Finalhook up is typicaly done through access openings in thebottom of the fixtures.

4

Figure 3

6570 COOLBROOK INSTALLATION

PRE INSTALLATIONThe Coolbrook fountain may be installed alone, or withthe matching cuspidor. Both units must be recessedinto the wall. See Figure 3 for size of the openings,and required reinforcement.

Be sure your installation conforms to local codes.

Install the opening in the wall for the fountain. Opening must be 23” tall and 13-1/2” wide. Seerecommended “Rim Height” above the floor. Install atheight to suit the application. If installing the matchingcuspidor, make an identical opening. Cuspidor locationshould be the same height above the floor.

3

2

If installing both fountain and cuspitor, a water line to connect the two must be placed beforethe fixtures are installed. If the back of the wall isopen so there is access to the back of the fixtures,the water connection can be made after fixtures areinstalled.

5

The fixture is shipped with the bubbler assembly packed in a cardboard box. Instructions on installingthe bubbler / cuspidor assembly are included in thebox. Read and follow those instuctions. The diagrambelow should help guide the instal lat ion.

7

Waste fitting with 1-1/4” O.D. tailpiece should be installed on fixture before it is installed. Assembleas shown in Figure 4. Tailpiece connects to previouslyinstalled waste line. If using “P” Trap only, connect todrain area. Assemble as shown in Figure 4.

6Plated Bolt

Washer

RubberGasket

Brass“P”

Trap

Chrome Bolt

Chrome Washer(Countersunk)

Brass Drain

Coupler Nut

Brass Washer

Rubber Grommet

Figure 4

Drain Assemblywith “P” Trap

1/2” Quick ConnectGalzanizedCoupling

Chrome Elbowwith Tubing

Valve Body

Rubber Gasket

StainlessWasher

Push ButtonAssembly

ChromeLock Nut

BrassLock NutBrass

ElbowConnect to

Water Supply

PlasticTee

In LineFlow Control

Polybraid withBrass Swivel

FemaleConnector

GalvanizedBracket

S.S. Cover Plate

S.S.Screws

Polybraid

1/4” 90d.Fitting

Brass Nut

Plated Washer

1/4” NPT Nipple4” long

Bullet Head Bubblerwith 1/4” NPT-F Inlet

Bubbler / CuspidorAssembly

3

Cuspidor

Plated MetalWasher

FiberWasher Brass

Elbowwith Nut

BrassNut

RubberWasher

Fit fixtures ito wall openings. Install mounting lag screws. Make water supply connections andconnect waste line. Turn on water and check for leaks.Install stainless steel cover plate.

Caulk any gap along edge of fixture and finished wallto complete the installation.

8

Waste Fitting

Cover Plate Assembly

Figure 6

Figure 6

MountingLag Screws

RubberGasket

1

2

3

4

5

6

7

1

2

3

4

1

2

3

4

5

67

8

2

9

10

11

12

13

1415

16

17

1

3

14

18

19

21

20

22

2324

24

Packing List 6523 Neu-Waterfall

No: Qty. Description

1 1

2 1 N.P.T. Nipple

3 1 Plated Metal Washer

4 1 Brass Nut

5 1 Female Connector

6 1 Copper Tubing “U”

7 1 Copper Tubing “L”

8 1 Plastic Strainer

9 1 Push Button Body

10 1 Cartridge

11 1 Brass Nut

12 1 Push Button Assembly

Metal Hanger1

Mounting Screws

13

No: Qty. Description1 1

2 1Chrome Bolt

3 1

Chrome Washer

4 1

Rubber Gasket

Brass “P” Trap

Packing List “P” Trap Assembly

No: Qty. Description1 1

2 1Chrome Bolt

3 1

Chrome Washer

4 1

Rubber Gasket

Waste Fitting

Packing List Waste Assembly

5 1 Coupler Nut

6 1 Brass Flat Washer

7 1 Rubber Grommet

No: Qty. Description1 1

2 1S.S. Cover Plate

3 2

Galvanized Bracket

S.S. Screws

Packing List Cover Plate Assembly

Packing List 6615 Fountain-Cuspidor

14 2

Purflo BubblerNo: Qty. Description

1 1

2 1 N.P.T. Nipple

3 1 Plated Metal Washer

4 1 Brass Nut

5 1 Female Connector

6 1 90 Degree Fitting

7 1 Polybraid /w Swivel

8 1 Flow Control

9 1 Plastic Tee

10 1 Chrome Elbow

11 1 Valve Body

12 1 Rubber Gasket

S.S. Washer1

Mounting Screws

13

14 1

Purflo Bubbler

Push Button Assembly15 1 Chrome Lock Nut16 1 Brass Lock Nut17 1 Brass Elbow18 1 Polybraid Tubing19 1 Quick Connect Coupling20 1 Brass Elbow /w Nut21 1 Fibre Washer22 1 Brass Nut23 2 Rubber Washer24 1 Plated Metal Washer25 1 Cuspidor

Subject to the “Exclusions” set forth below, CR/PLpromises to the consumer to repair, or at the optionof CR/PL, to replace any part of this plumbing productwhich proves to be defective in workmanship ormaterials under normal use for five years from thedate of purchase. All costs of removal, transportationand reinstallation to obtain warranty service shall bepaid by the consumer. During this five year period,CR/PL will provide, subject to the “Exclusions” sectionset forth below, all parts free of charge, necessaryto correct such defects if this plumbing product hasbeen installed and maintained in accordance withwritten instructions furnished by CR/PL with thisplumbing product.

Exclusions: CR/PL PRODUCTS SHALL NOT BELIABLE FOR INCIDENTAL OR CONSEQUENTIALDAMAGES, INCLUDING COSTS OF INSTALLATION

OR WATER DAMAGE, OR FOR DAMAGESRESULTING FROM ABUSE OR MISUSE OR FROMFAILURE TO INSTALL OR MAINTAIN THISPLUMBING PRODUCT IN ACCORDANCE WITHTHE WRITTEN INSTRUCTIONS FURNISHED BYCR/PL PRODUCTS. USE OF CLEANINGP R O D U C T S C O N TA I N I N G C A L C I U MHYPOCHLORITE (CHLORINE) SHALL CONSTITUTEIMPROPER MAINTENANCE. SOME STATES DONOT ALLOW THE EXCLUSION OR LIMITATION OFINCIDENTAL OR CONSEQUENTIAL DAMAGES, SOTHE ABOVE LIMITATION MAY NOT APPLY TO THECONSUMER. THE ONLY WARRANTY MADE BYCR/PL PRODUCTS IS SET FORTH ABOVE ANDALL IMPLIED WARRANTIES WHICH MIGHT ARISE,INCLUDING THE IMPLIED WARRANTIES OFMERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE ARE HEREBYEXCLUDED.Warranty Service: In order to obtain warrantyservice or adjustments, contact the builder, dealeror plumber from whom the product waspurchased, or the Customer Service Department,CR/PL Products, 201 East Fifth Street, Mansfield,OH 44901 (419/522-4211). In obtaining warrantyservice, all transportation, shipping and freightcharges connected with transporting any part ofthis plumbing product must be prepaid by theconsumer. It is the responsibility of the consumerto establish the warranty period by verifying theoriginal purchase date. A bill of sale, cancelledcheck or some other appropriate payment recordmay be kept for this purpose. This warranty givesyou specific legal rights. You may also have otherrights which vary from state to state.

Limited Five Year Warranty

CR/PL 1235 Hartrey Avenue Evanston, IL. 60202

FORM NO: 2071 5/23/02. PRINTED IN U.S.A.