INSTALLATION INSTRUCTIONS FOR PART 95-8202 · PDF fileScion XB 2008 ... SCION XA 2004-2006 12...
Transcript of INSTALLATION INSTRUCTIONS FOR PART 95-8202 · PDF fileScion XB 2008 ... SCION XA 2004-2006 12...
INSTALLATION INSTRUCTIONS FOR PART 95-8202
Cutting Tool • Phillips Screwdriver • Socket Set • Grinder
1-800-221-0932 www.metraonline.com
KIT FEATURES
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
• DDIN Head Unit Provision• Stacked ISO DIN Head Unit Provision
A) DDIN Trim plates
KIT COMPONENTS
TOOLS REQUIRED:A
APPLICATIONSToyota
Rav 4 2001-05 MR2 Spider 2000-05
Celica 2000-05 Echo 2000-05
Highlander 2001-07 Matrix 2005-07
4 Runner (Excluding Limited) 2003-07 Tundra 2003-06Sequoia 2003-07
FJ Cruiser 07Yaris 2007
Scion TC 2005-07 / XA 2004-06 / XB 2004-08
95-8202
TABLE OF CONTENTS
95-8202
Dash DisassemblyToyota Rav 4 2001-2005............................................................... 1Toyota MR2 Spyder 2000-2005 .................................................... 2Toyota Celica 2000-2005 ............................................................. 3Toyota Echo 2000-2005 ............................................................... 4Toyota Highlander 2001-2006 ..................................................... 5Toyota Matrix 2005-2007 ............................................................. 6Toyota 4 Runner (Excluding Limited) 2003-2006 ......................... 7Toyota Tundra 2003-2006 ............................................................. 8Toyota Sequoia 2003-2006........................................................... 9Toyota FJ Cruiser 2007............................................................... 10Yaris 2007....................................................................................11Scion XA 2004-2006 ....................................................................12Scion XB 2004-2007 ....................................................................13Scion XB 2008 .............................................................................14Scion TC 2005-2007 ..................................................................15
Kit AssemblyDouble DIN Head Unit Provision.................................................. 16Stacked ISO DIN Head Unit Provision ......................................... 16
Final Assembly ............................................................................17
95-8202
1
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip and remove side panel fromboth sides of radio and climatecontrols. Figure A)
2
TOYOTA RAV 4 2001-2005
Remove (4) Phillips screws securingthe radio/climate control trim panel.(Figure B)
3
Remove (4) 10 MM bolts securing theradio. (Figure C)
4
DASH DISASSEMBLY
A
B
C
Continue to kit assembly.
Unplug and remove radio.5
Remove factory brackets from radio.Retain brackets for use during kitassembly.
6
7
95-8202 DASH DISASSEMBLY
TOYOTA MR2 SPIDER 2000-2005
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
Unsnap the lower trim piece fromeach side of the dash console andremove (2) Phillips screws exposed ineach cavity. Remove the upper trimpiece from each side of the console.(Figure A)
2
Remove the climate control knobsand (2) Phillips screws exposed.Remove the climate control trimbezel. (Figure A)
3
Remove the ashtray and (1) 10mmbolt exposed. Unclip the ashtray trimbezel and remove. (Figure A)
Unclip the radio trim bezel, remove(4) Phillips screws securing the unitand disconnect the wiring.
4
1
5
2
A
Continue to kit assembly.7
6 Remove factory brackets from radio.Retain brackets for use during kitassembly.
3
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip and remove the gear shiftertrim bezel and remove (2) Phillipsscrews exposed below the climatecontrols. (Figure A)
2
Unclip the climate control/factoryradio trim bezel and remove.(Figure A)
4
Remove (4) 10mm screws securingthe factory head unit and disconnectthe wiring.
5
Pull off climate control knobs andremove (2) Phillips screws exposed.(Figure A)
3
TOYOTA CELICA 2000-2005
A
95-8202 DASH DISASSEMBLY
Continue to kit assembly.7
6 Remove factory brackets from radio.Retain brackets for use during kitassembly.
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1A
4
95-8202 DASH DISASSEMBLY
TOYOTA ECHO 2000-2005
Remove the climate control knobsand (2) Phillips screws exposed.Unclip and remove the climate con-trol trim bezel. Depress the sideclips securing the climate controlpanel and move the panel to access(2) Phillips screws from the top ofthe factory radio brackets. (Figure A)
2
Remove the ashtray. Unclip andremove the radio trim bezel. Remove(2) Phillips screws from the bottomof the radio brackets and disconnectthe wiring.
3
Continue to kit assembly.5
4 Remove factory brackets from radio.Retain brackets for use during kitassembly.
5
Pull and remove dash panel fromradio and climate controls. Tip: Thereare 8 clips. (Figure A)
2
Remove (6) 10mm bolts from radioand climate controls assembly.(Figure B)
3
Remove assembly and disconnectthe wiring.
4
Remove (8) Phillips bolts and (4) Phillipsscrews to separate brackets from assem-bly. Retain brackets for use duringkit assembly. (Figure C)
5
A
B
C
95-8202 DASH DISASSEMBLY
TOYOTA HIGHLANDER 2001-2006
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Continue to kit assembly.6
6
95-8202 DASH DISASSEMBLY
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip the bottom edge of the radiotrim panel then lift up and out toremove. (Figure A)
2
Remove (4) 10 MM bolts securingthe factory radio. (Figure B)
3
A
SCAN
SEEKTRACK
TUNE
AM FM1 FM2 DISK
B
TOYOTA MATRIX 2005-2007
7
95-8202
TOYOTA 4 RUNNER 2003-2006(EXCLUDING LIMITED)
DASH DISASSEMBLY
Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.Unsnap and remove trim from aroundshifter.
Unsnap and remove trim covers fromaround center console pocket edgeat front and rear of console.
1
2
Unsnap and remove entire centerpanel around radio. (Figure D)
10
Remove (2) 10 mm bolts securingradio.
11
3
Unsnap and remove center consolecover. (Figure A)
4
Unsnap trim ring from around ignitionkey cylinder. Remove (1) 10 mm bolt from bottomright of panel below steering column.Unsnap panel and pull away to gainaccess behind panel. (Figure B)
5
6
Remove (1) 10 mm bolt on bottomleft of center panel behind panelbelow steering column. (Figure B)
7
Remove (1) 10 mm bolt beneath cli-mate control behind pocket door.Unsnap and remove climate control.(Figure C)
8
Remove (2) 10 mm bolts beneathradio behind climate controls.
9
A
B
C
D
12 Unplug and remove radio.
Continue to kit assembly.14
13 Remove factory brackets from radio.Retain brackets for use during kitassembly.
95-8202
8
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Remove the (3) climate control knobs bypulling straight outward. (Figure A)
2
TOYOTA TUNDRA 2003-2006
Remove (3) Phillips screws frombehind knobs. (Figure A)
3
Unclip and remove entire trim panel. (Figure C)
5
6
4
DASH DISASSEMBLY
A
B
D C
7
Position vents facing upward andremove (1) Phillips screw from eachA/C vent. (Figure B)
Remove (4)10 mm bolts to removeradio. (Figure D)
Unplug and remove radio.
Continue to kit assembly.9
8 Remove factory brackets from radio.Retain brackets for use during kitassembly.
95-8202
9
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
2
TOYOTA SEQUOIA 2003-2006
Unclip and remove entire radio trimpanel including climate controls.(Figure B)
3
Remove (4) 10 mm bolts to removeradio. (Figure C)
4
DASH DISASSEMBLY
A
B
C
Continue to kit assembly.
5
Position vents facing upward andremove (1) Phillips screw from eachA/C vent. (Figure A)
Unplug and remove radio.
7
6 Remove factory brackets from radio.Retain brackets for use during kitassembly.
95-8202
10
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Remove two Phillips screws frombottom part of side trim panels.Figure A)
2
TOYOTA FJ CRUISER 2007
Using a panel removal tool, carefullyremove the side trim panels.(Figure B)
3
Remove (2) Phillips screws from radiotrim panel. (Figure C)
4
Using panel removal tool, carefullyremove radio trim panel. (Figure D)
5
Remove (4) 10mm bolts securing theradio.
6
7
DASH DISASSEMBLY
A
B
CD
Unplug and remove radio.
Continue to kit assembly.9
8 Remove factory brackets from radio.Retain brackets for use during kitassembly.
95-8202
11
Disconnect the negative battery terminal to prevent an accidentalshort circuit.
1
Unclip the bottom trim panel locatedunderneath the A/C Controls.Figure A)
2
YARIS 2007
Unclip the two side trim panels thatsurround the A/C Controls and Radio.(Figure A)
3
Unclip the Instrument trim Panelsurrounding the Speedometer andgauges. (Figure B)
4
Unclip the Radio/AC Vents trimPanel.(Figure B)
5
Remove (4) Phillips screws securingradio. (Figure C)
6
Continue to kit assembly.
7
DASH DISASSEMBLY
A
B
C
Unplug and remove radio.
8 Remove (4) Phillips screws securingfactory brackets on each side of theradio and remove brackets. Retainbrackets for use during kit assembly.(Figure D)
D
9
95-8202 DASH DISASSEMBLY
SCION XA 2004-2006
12
Disconnect the negative battery terminalto prevent an accidental short circuit.
Pull outward on the (3) climate controlknobs and remove. (Figure A)
1
2
Remove (2) Phillips screws from behindthe outer two climate knobs. (Figure B)
3
A
B
Unsnap and remove the trim pieces oneach side of the climate control/ash-tray/pocket assembly. (Figure C)
4
Remove (2) phillips screws from thebottom of the climate control/radio trimpanel and unsnap and remove the entirepanel. (Figure D)
5
Remove (4) Phillips screws to removethe factory radio.
6
C
DContinue to kit assembly.8
7 Remove factory brackets from radio.Retain brackets for use during kitassembly.
95-8202 DASH DISASSEMBLY
SCION XB 2004-2007
13
Disconnect the negative battery terminalto prevent an accidental short circuit.
Pull outward on the (3) climate controlknobs and remove. (Figure A)
1
2
Remove (2) Phillips screws from behindthe outer (2) knobs. (Figure B)
3
A
BUnsnap and remove the entire panelsurrounding the climate controls andthe radio. (Figure C)
4
Remove (4) Phillips screws to removethe factory radio.
5
Continue to kit assembly.7
6 Remove factory brackets from radio.Retain brackets for use during kitassembly.
95-8202 DASH DISASSEMBLY
SCION XB 2008
14
Unclip and remove the trim panelaround the radio including the a/c vents.(Figure A)
Unclip and remove the trim panel at thebottom edge of the dash cavity. (Figure B)
1
2
Remove (4) 10 MM bolts securing theradio. (Figure C)
3
A
B
C
Continue to kit assembly.
95-8202 DASH DISASSEMBLY
SCION TC 2005-2007
15
Disconnect the negative battery termi-nal to prevent an accidental short cir-cuit.
Unsnap trim from around shifter (notnecessary to be removed). (Figure A)
1
2
Unclip and remove panel from aroundradio. (Including climate controls andradio door). (Figure B)
3
A
B
Remove (2) 10mm nuts from the topmounting locations and (2) 10mm boltsfrom the bottom mounting locations toremove the radio. (Figure C)
4
C5 Remove factory brackets from radio.
Retain brackets for use during kitassembly.
Continue to kit assembly.6
16
Attach the factory mounting bracketsand the 95-8202 DDIN trim plates tothe DDIN head unit with the screwssupplied with the unit. (Figure B)NOTE: Remove locating pins from fac-tory brackets with grinder.
1
Attach the factory mounting bracketsand the 95-8202 DDIN trim plates tothe stacked ISO DIN head units withthe screws supplied with the units.(Figure C) NOTE: Remove locating pinsfrom factory brackets with grinder.
Continue to final assembly.
1
A
A
A
B
B
C
DOUBLE DIN HEAD UNIT PROVISION
STACKED ISO HEAD UNIT PROVISION
B
95-8202 KIT ASSEMBLY
NOTE: For all Scion TC and XA you willneed to cut off the front upper section ofthe DDIN trim plates, as shown by dottedlines labeled “A” in (Figure A).For the 2001-2006 Toyota Rav 4, the2001-2006 Toyota Highlander, and the2003-2006 Toyota Sequoia/Tundra youwill need to cut off the rear section ofthe DDIN trim plates, as shown by dottedlines labeled “B” in (Figure A).For all other vehicles skip to Step 1.
17
FINAL ASSEMBLY1 Locate the factory wiring harness in the dash and make the connection as shown.
Metra recommends using the proper mating adapter and making the connectionsas shown. (Isolate and individually tape off the ends of any unused wires to pre-vent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.3 Reassemble radio and dash assemblies in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-) . . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
95-8202 FINAL ASSEMBLY