© 2016 Raymarine UK Limited81367-1Document number:11-2016Date:

English (en-US)

INSTALLATION INSTRUCTIONS

RMK-10

Trademark and patents noticeRaymarine, Tacktick, Clear Pulse, Truzoom, HSB, SeaTalk, SeaTalkhs, SeaTalkng, Micronet, Raytech,Gear Up, Marine Shield, Seahawk, Autohelm, Automagic, and Visionality are registered or claimedtrademarks of Raymarine Belgium.FLIR, DownVision, SideVision, Dragonfly, Quantum, Instalert, Infrared Everywhere, and The World’sSixth Sense are registered or claimed trademarks of FLIR Systems, Inc.All other trademarks, trade names, or company names referenced herein are used for identification onlyand are the property of their respective owners.This product is protected by patents, design patents, patents pending, or design patents pending.

Fair Use StatementYou may print no more than three copies of this manual for your own use. You may not make any furthercopies or distribute or use the manual in any other way including without limitation exploiting the manualcommercially or giving or selling copies to third parties.

Software updates

Important: Check the Raymarine website for the latest software releases for your product.

www.raymarine.com/software

Product handbooksThe latest versions of all English and translated handbooks are available to download in PDF format from the websitewww.raymarine.com.Please check the website to ensure you have the latest handbooks.

Copyright ©2016 Raymarine UK Ltd. All rights reserved.

English (en-US)Document number: 81367-1Date: 11-2016

ContentsChapter 1 Important information............. 7

Water ingress ............................................ 7Disclaimer.................................................. 7EMC installation guidelines ....................... 7Declaration of conformity........................... 8Product disposal........................................ 8Warranty registration ................................. 8IMO and SOLAS........................................ 8Technical accuracy.................................... 8

Chapter 2 Document and productinformation................................................ 9

2.1 Document information ....................... 10Product documentation ........................... 10

2.2 Product overview............................... 10Compatibility............................................ 10

Chapter 3 Planning theinstallation................................................11

3.1 Installation checklist .......................... 12Schematic diagram ................................. 12

3.2 Parts supplied.................................... 123.3 Software updates .............................. 133.4 Tools required.................................... 133.5 General location requirements .......... 14

Product dimensions................................. 143.6 Warnings and cautions...................... 14

Chapter 4 Cables andconnections ............................................ 15

4.1 General cabling guidance.................. 16Cable types and length ........................... 16Routing cables ........................................ 16Strain relief .............................................. 16Cable shielding........................................ 16Suppression ferrites ................................ 16

4.2 Connections overview ....................... 174.3 Alternate power connection............... 17

Grounding — Dedicated drainwire.......................................................... 17

4.4 Keypad connections.......................... 18

Chapter 5 Mounting................................ 215.1 Removing the keypad mat................. 225.2 Flush mounting the keypad ............... 225.3 Surface mounting the keypad............ 23

5.4 Fitting the keypad mat ....................... 23

Chapter 6 Operation............................... 256.1 Keypad controls................................. 266.2 Pairing the keypad............................. 27

Switching the active pane or displayusing the keypad..................................... 27Unpairing the keypad .............................. 27Unpairing from all displays ...................... 27Determining the active display ................ 27

Chapter 7 System checks andtroubleshooting ...................................... 29

7.1 Keypad status.................................... 307.2 PoE troubleshooting.......................... 307.3 Power up troubleshooting.................. 31

Chapter 8 Maintenance .......................... 338.1 Service and maintenance.................. 348.2 Routine equipment checks................ 348.3 Product cleaning................................ 35

Chapter 9 Technical specification......... 379.1 Technical specification....................... 389.2 Compliance ....................................... 38

Chapter 10 Technical support ............... 3910.1 Raymarine product support andservicing .................................................. 40

Viewing product information.................... 4010.2 Learning resources.......................... 41

Chapter 11 Spares andaccessories............................................. 43

11.1 Keypad spares andaccessories ............................................. 44

RayNet to RayNet cables andconnectors............................................... 45RayNet to RJ45 adapter cables .............. 46

5

6

Chapter 1: Important informationWarning: Product installationand operation• This product must be installed andoperated in accordance with theinstructions provided. Failure to do socould result in personal injury, damageto your vessel and/or poor productperformance.

• Raymarine recommends certifiedinstallation by a Raymarine approvedinstaller. A certified installation qualifiesfor enhanced product warranty benefits.Contact your Raymarine dealer forfurther details, and refer to the separatewarranty document packed with yourproduct.

Warning: Potential ignitionsourceThis product is NOT approved for use inhazardous/flammable atmospheres. DoNOT install in a hazardous/flammableatmosphere (such as in an engine roomor near fuel tanks).

Warning: Product groundingBefore applying power to this product,ensure it has been correctly grounded, inaccordance with the instructions provided.

Warning: Positive groundsystemsDo not connect this unit to a system whichhas positive grounding.

Warning: Switch off powersupplyEnsure the vessel’s power supply isswitched OFF before starting to install thisproduct. Do NOT connect or disconnectequipment with the power switched on,unless instructed in this document.

Caution: Power supplyprotectionWhen installing this product ensure thepower source is adequately protectedby means of a suitably-rated fuse orautomatic circuit breaker.

Water ingressWater ingress disclaimerAlthough the waterproof rating capacity of thisproduct meets the IPX6 standard, water intrusionand subsequent equipment failure may occur if theproduct is subjected to commercial high-pressurewashing. Raymarine will not warrant productssubjected to high-pressure washing.

DisclaimerRaymarine does not warrant that this product iserror-free or that it is compatible with productsmanufactured by any person or entity other thanRaymarine.Raymarine is not responsible for damages or injuriescaused by your use or inability to use the product,by the interaction of the product with productsmanufactured by others, or by errors in informationutilized by the product supplied by third parties.

EMC installation guidelinesRaymarine equipment and accessories conform tothe appropriate Electromagnetic Compatibility (EMC)regulations, to minimize electromagnetic interferencebetween equipment and minimize the effect suchinterference could have on the performance of yoursystemCorrect installation is required to ensure that EMCperformance is not compromised.

Note: In areas of extreme EMC interference,some slight interference may be noticed on theproduct. Where this occurs the product and thesource of the interference should be separated bya greater distance.

For optimum EMC performance we recommendthat wherever possible:• Raymarine equipment and cables connected toit are:– At least 1 m (3 ft) from any equipmenttransmitting or cables carrying radio signals e.g.VHF radios, cables and antennas. In the caseof SSB radios, the distance should be increasedto 7 ft (2 m).

– More than 2 m (7 ft) from the path of a radarbeam. A radar beam can normally be assumedto spread 20 degrees above and below theradiating element.

• The product is supplied from a separate batteryfrom that used for engine start. This is important toprevent erratic behavior and data loss which canoccur if the engine start does not have a separatebattery.

• Raymarine specified cables are used.• Cables are not cut or extended, unless doing so isdetailed in the installation manual.

Important information 7

Note: Where constraints on the installationprevent any of the above recommendations,always ensure the maximum possible separationbetween different items of electrical equipment, toprovide the best conditions for EMC performancethroughout the installation

Declaration of conformityRaymarine UK Ltd. declares that this product iscompliant with the essential requirements of EMCdirective 2004/108/EC.The original Declaration of Conformity certificatemay be viewed on the relevant product page atwww.raymarine.com.

Product disposalDispose of this product in accordance with theWEEE Directive.

The Waste Electrical and Electronic Equipment(WEEE) Directive requires the recycling of wasteelectrical and electronic equipment.

Warranty registrationTo register your Raymarine product ownership,please visit www.raymarine.com and register online.It is important that you register your product toreceive full warranty benefits. Your unit packageincludes a bar code label indicating the serial numberof the unit. You will need this serial number whenregistering your product online. You should retainthe label for future reference.

IMO and SOLASThe equipment described within this documentis intended for use on leisure marine boats andworkboats NOT covered by International MaritimeOrganization (IMO) and Safety of Life at Sea(SOLAS) Carriage Regulations.

Technical accuracyTo the best of our knowledge, the information in thisdocument was correct at the time it was produced.However, Raymarine cannot accept liability for anyinaccuracies or omissions it may contain. In addition,our policy of continuous product improvement maychange specifications without notice. As a result,Raymarine cannot accept liability for any differencesbetween the product and this document. Pleasecheck the Raymarine website (www.raymarine.com)to ensure you have the most up-to-date version(s) ofthe documentation for your product.8

Chapter 2: Document and product information

Chapter contents• 2.1 Document information on page 10• 2.2 Product overview on page 10

Document and product information 9

2.1 Document informationThis document contains important informationrelated to the installation of your Raymarine product.The document includes information to help you:• plan your installation and ensure you have all thenecessary equipment;

• install and connect your product as part of a widersystem of connected marine electronics;

• troubleshoot problems and obtain technicalsupport if required.

This and other Raymarine product documentsare available to download in PDF format fromwww.raymarine.com.

Product documentationThe following documentation is applicable to yourproduct:Description Part numberInstallation and operationinstructions

81367

RMK-10 Mounting template 87283

2.2 Product overviewThe RMK-10 is a Remote Keypad for Raymarinemultifunction displays (MFD). The keypad is a class1 PoE (Power Over Ethernet) device and can bepowered either using a suitable network connection,that is providing PoE, or directly using the dedicatedAlternate power connector. The keypad includesan internal buzzer that is used to repeat key pressbeeps and MFD alarms.The keypad can be mounted in landscape or portraitorientation.

Part number DescriptionA80438 RMK-10 — Portrait orientation

When ordering A80438 only the portraitkeypad mat is supplied.

T70293 RMK-10 — Landscape orientationWhen ordering T70293 both orientationkeypad mats are supplied.

CompatibilityThe RMK-10 is compatible with the followingLightHouse™ powered MFDs.• a Series• c Series• e Series• gS Series• eS SeriesMFDs require LightHouse™ software release 7 orlater.

10

Chapter 3: Planning the installation

Chapter contents• 3.1 Installation checklist on page 12• 3.2 Parts supplied on page 12• 3.3 Software updates on page 13• 3.4 Tools required on page 13• 3.5 General location requirements on page 14• 3.6 Warnings and cautions on page 14

Planning the installation 11

3.1 Installation checklistInstallation includes the following activities:

Installation Task1 Plan your system.2 Obtain all required equipment and tools.3 Site all equipment.4 Route all cables.5 Drill cable and mounting holes.6 Make all connections into equipment.7 Secure all equipment in place.8 Power on and test the system.

Schematic diagramA schematic diagram is an essential part of planningany installation. It is also useful for any futureadditions or maintenance of the system. Thediagram should include:• Location of all components.• Connectors, cable types, routes and lengths.

3.2 Parts suppliedThe parts supplied with the keypad are shown below.

1. RMK-10 keypad2. Landscape keypad mat

Note: The Landscape keypad mat is onlysupplied with T70293

3. Portrait keypad mat (supplied fitted to the unit)4. Mounting gasket5. 4 x mounting fixings6. Documentation pack7. Right angled power cable 2 m (6.6 ft.)8. RayNet network cable 2 m (6.6 ft.)

12

3.3 Software updatesThe software running on the product can be updated.• Raymarine periodically releases software updatesto improve product performance and add newfeatures.

• The software on many products can be updatedusing a connected and compatible multifunctiondisplay (MFD).

• Refer to www.raymarine.com/software/ for thelatest software updates and the software updateprocedure for your specific product.

Important:• To prevent potential software-related issues withyour product, always follow the relevant updateinstructions carefully and in the sequenceprovided.

• If in doubt as to the correct procedure forupdating your product software, refer to yourdealer or Raymarine technical support.

Caution: Installing softwareupdatesThe software update process is carriedout at your own risk. Before initiating theupdate process ensure you have backedup any important files.Ensure that the unit has a reliable powersupply and that the update process is notinterrupted.Damage caused by incomplete updatesare not covered by Raymarine warranty.By downloading the software updatepackage, you agree to these terms.

3.4 Tools requiredProduct installation requires the following tools:Item Description Quantity

Power drill 1

Pozidrive screwdriver 1

Drill bit of appropriate size* 1

Adhesive tape 1

Note: * The appropriate drill bit size is dependenton the thickness and material of the mountingsurface.

Planning the installation 13

3.5 General location requirementsImportant considerations when choosing a suitablelocation for your product.This product is suitable for mounting above or belowdecks.The product should be mounted where it will be:• protected from physical damage and excessivevibration.

• well ventilated and away from heat sources.• away from any potential ignition source such as anengine room, near fuel tanks or a gas locker.

When choosing a location for the product,consider the following points to ensure reliable andtrouble-free operation:• Access — there must be sufficient space toenable cable connections to the product, avoidingtight bends in the cable.

• Diagnostics — the product must be mounted ina location where the diagnostics LED is easilyvisible.

Note: Not all products include a diagnosticsLED. Refer to the Chapter 7 System checksand troubleshooting for more information.

• Electrical interference — the product should bemounted far enough away from any equipmentthat may cause interference such as motors,generators and radio transmitters / receivers.

• Magnetic compass — refer to the Compasssafe distance section in this document for adviceon maintaining a suitable distance between thisproduct and any compasses on your vessel.

• Power — to keep cable runs to a minimum, theproduct must be located as close as possible tothe vessel’s dc power supply.

• Mounting surface — ensure the product isadequately supported on a secure surface. Referto the weight information provided in the Technicalspecification for this product and ensure that theintended mounting surface is suitable for bearingthe product weight. Do NOT mount units or cutholes in places which may damage the structureof the vessel.

Product dimensions

3.6 Warnings and cautionsImportant: Before proceeding, ensure that youhave read and understood the warnings andcautions provided in the Chapter 1 Importantinformation section of this document.

14

Chapter 4: Cables and connections

Chapter contents• 4.1 General cabling guidance on page 16• 4.2 Connections overview on page 17• 4.3 Alternate power connection on page 17• 4.4 Keypad connections on page 18

Cables and connections 15

4.1 General cabling guidance

Cable types and lengthIt is important to use cables of the appropriate typeand length• Unless otherwise stated use only standard cablesof the correct type, supplied by Raymarine.

• Ensure that any non-Raymarine cables are of thecorrect quality and gauge. For example, longerpower cable runs may require larger wire gaugesto minimize voltage drop along the run.

Routing cablesCables must be routed correctly, to maximizeperformance and prolong cable life.• Do NOT bend cables excessively. Whereverpossible, ensure a minimum bend diameter of 200mm (8 in) / minimum bend radius of 100 mm (4 in).

• Protect all cables from physical damage andexposure to heat. Use trunking or conduit wherepossible. Do NOT run cables through bilges ordoorways, or close to moving or hot objects.

• Secure cables in place using tie-wraps or lacingtwine. Coil any extra cable and tie it out of the way.

• Where a cable passes through an exposedbulkhead or deckhead, use a suitable watertightfeed-through.

• Do NOT run cables near to engines or fluorescentlights.

Always route data cables as far away as possiblefrom:• other equipment and cables,• high current carrying AC and DC power lines,• antennae.

Strain reliefEnsure adequate strain relief is provided. Protectconnectors from strain and ensure they will not pullout under extreme sea conditions.

Cable shieldingEnsure that all data cables are properly shieldedthat the cable shielding is intact (e.g. hasn’t beenscraped off by being squeezed through a tight area).

Suppression ferrites• Raymarine cables may be pre-fitted or suppliedwith suppression ferrites. These are important forcorrect EMC performance. If ferrites are supplied

separately to the cables (i.e. not pre-fitted), youmust fit the supplied ferrites, using the suppliedinstructions.

• If a ferrite has to be removed for any purpose (e.g.installation or maintenance), it must be replaced inthe original position before the product is used.

• Use only ferrites of the correct type, supplied byRaymarine or its authorized dealers.

• Where an installation requires multiple ferrites tobe added to a cable, additional cable clips shouldbe used to prevent stress on the connectors dueto the extra weight of the cable.

16

4.2 Connections overview

1. Alternate power connector2. Network / PoE connectorThe alternate power connector is required whenconnecting to a network which does not supportPower over Ethernet PoE. The alternate powerconnector must be connected directly to a powersupply.

Note: Do not connect the alternate powerconnector to a SeaTalkng network.

Note: Only use one power source. There is noneed to connect the alternate power connectorwhen the keypad is being supplied PoE.

4.3 Alternate power connectionWhen the keypad is not supplied Power overEthernet (PoE) then the alternate power connectionshould be connected directly to a 12 V dc or 24 V dcpower supply.

1. Keypad2. Right angled power cable3. Black negative wire4. Ground / shield wire5. Red positive wire

Warning: Product groundingBefore applying power to this product,ensure it has been correctly grounded, inaccordance with the instructions provided.

Grounding — Dedicated drain wireThe power cable supplied with this product includesa dedicated shield (drain) wire for connection to avessel's RF ground point.It is important that an effective RF ground isconnected to the system. A single ground pointshould be used for all equipment. The unit can begrounded by connecting the shield (drain) wire ofthe power cable to the vessel's RF ground point.On vessels without an RF ground system the shield(drain) wire should be connected directly to thenegative battery terminal.The dc power system should be either:• Negative grounded, with the negative batteryterminal connected to the vessel's ground.

• Floating, with neither battery terminal connectedto the vessel's ground

Warning: Positive groundsystemsDo not connect this unit to a system whichhas positive grounding.

Cables and connections 17

4.4 Keypad connectionsThe keypad can be connected directly to amultifunction display’s (MFDs) network connectoror via a network switch. Multiple keypads can beconnected to a system. Each keypad can be used tocontrol multiple MFDs. If the network is not providingPower over Ethernet (PoE) then the keypad must bepowered using the Alternate power connector.

Note: When connecting the keypad to a gS SeriesMFD, ensure that the supplied RayNet cable isconnected with the suppression ferrite fitted on theend of the cable closest to the MFD.

Direct MFD connection with PoE

1. gS Series (MFD providing PoE)2. RMK keypad3. RayNet network cable (with suppression ferrite

fitted)

Direct MFD connection without PoE

1. MFD2. RayNet network cable3. RMK keypad4. Right angled power cable (Connected to the

alternate power connector.)

Direct MFD connection with PoE injector

1. MFD2. RMK keypad

3. RayNet to RJ45 network cable (A62360, A80151or A80159)

4. PoE injector power supply (12 / 24 V dc)5. PoE injector (R32141)

Network connection via MFD with PoE

1. gS Series (MFD providing PoE)2. RMK keypad3. RayNet network cable (with suppression ferrite

fitted)4. Networked MFDs

Note: The keypad can be used to controlnetworked MFDs even when the MFD it isconnected to is switched off, as long as the MFDstill has power supplied to it.

Network connection via network switch

In the illustration above a PoE injector could be usedinstead of the Alternate power connection.1. Network switch2. RMK keypad

18

3. Right angled power cable (Connected to thealternate power connector.)

4. Networked MFDs

Note: Once connected the keypad must be pairedwith each MFD you want to control with the keypad.

Cables and connections 19

20

Chapter 5: Mounting

Chapter contents• 5.1 Removing the keypad mat on page 22• 5.2 Flush mounting the keypad on page 22• 5.3 Surface mounting the keypad on page 23• 5.4 Fitting the keypad mat on page 23

Mounting 21

5.1 Removing the keypad matTo gain access to the mounting hole locations, thekeypad mat must be removed.

Tip To help prevent scratching the product, cover thetip of your screwdriver blade with a small piece ofinsulation tape.1. Using a thin, flat bladed screwdriver insert the tip

of the screwdriver into the gap between the edgeof the keypad mat and the keypad housing, at alocation between locking tabs.

2. Gently lever the keypad mat away from thekeypad to release the keypad mat.

Take care not to bend the keypad mat duringremoval.

5.2 Flush mounting the keypadFlush mounting provides a sleek installation wherethe product and dash are flush, with only the buttonsand Rotary controller protruding from the dash.Flush mounting requires the mounting surface to berebated.

1. Check the selected location for the unit. A clear,flat area with suitable clearance behind the panelis required.

2. Before modifying the mounting surface, referto the dimensions supplied in this document toensure there is enough space for the unit and allcables.

3. Fix the supplied mounting template to theselected location, using masking or self adhesivetape.

4. Drill 4 holes as indicated on the mountingtemplate to accept the fixings.

5. Using a suitable hole saw (the size and positionis indicated on the template), make a hole in eachcorner of the cut-out area.

6. Using a suitable saw, cut along the inside edgeof the cut-out line.

7. Using a Router, follow the Flush mount rebateline, to cut out a rebate to the specified rebatedepth, as indicated on the template.

8. Ensure that the unit fits into the removed areaand then remove rough edges.

9. Place the supplied gasket onto the rear of thekeypad, ensuring the mounting holes are aligned.

10.Connect the relevant cables to the unit.11. Place the keypad into the rebate and secure

using the fixings provided.

Note: The appropriate tightening torque and drillbit size to use depends on the thickness of themounting surface and the type of material it ismade from.

Note: The supplied gasket provides a sealbetween the unit and a suitably flat and stiffmounting surface or binnacle. The gasket shouldbe used in all installations. It may also benecessary to use a marine-grade sealant if themounting surface or binnacle is not entirely flat andstiff or has a rough surface finish.

22

5.3 Surface mounting the keypadSurface mounting provides a uniform installationwhere the products protrude, usually by the thicknessof the bezel, from the mounting surface.

1. Check the selected location for the unit. A clear,flat area with suitable clearance behind the panelis required.

2. Before modifying the mounting surface, referto the dimensions supplied in this document toensure there is enough space for the unit and allcables.

3. Fix the supplied mounting template to theselected location, using masking or self adhesivetape.

4. Drill 4 holes as indicated on the mountingtemplate to accept the fixings.

5. Using a suitable hole saw, make a hole in eachcorner of the cut-out area.

6. Using a suitable saw, cut along the inside edgeof the cut-out line.

7. Ensure that the unit fits into the removed areaand then remove rough edges.

8. Place the supplied gasket onto the rear of thekeypad, ensuring the mounting holes are aligned.

9. Connect the relevant cables to the unit.10.Secure using the fixings provided.

Note: The appropriate tightening torque and drillbit size to use depends on the thickness of themounting surface and the type of material it ismade from.

Note: The supplied gasket provides a sealbetween the unit and a suitably flat and stiffmounting surface or binnacle. The gasket shouldbe used in all installations. It may also benecessary to use a marine-grade sealant if themounting surface or binnacle is not entirely flat andstiff or has a rough surface finish.

5.4 Fitting the keypad matYour keypad can be installed in portrait or landscapeorientation. keypad mats are available for eachorientation.• You should fit the keypad mat that matches yourchosen mounting orientation.

• You should only fit the keypad mat after the unithas been secured to the mounting surface.

1. Ensure the keypad mat is orientated correctly.2. Slide the keypad mat’s shorter edge, with the 2

locking tabs, into the end of the keypad that has2 notches to accept the tabs.

3. Close the opposite end of the keypad mat intothe keypad, ensuring that the tab slides into thenotch provided, push all of the tabs on the longersides into their notches (you should hear a clickas each tab engages).

Mounting 23

24

Chapter 6: Operation

Chapter contents• 6.1 Keypad controls on page 26• 6.2 Pairing the keypad on page 27

Operation 25

6.1 Keypad controlsConnecting the keypad allows you to control yourmultifunction display remotely.

1. Home— press to return to the Homescreen.2. Menu— accesses menus. Press again to close

menus.3. UniController — provides a rotary control and

a joystick that includes an OK push button forusing menus and applications.

4. Back — press to return to a previous menu ordialog level.

5. - (Minus/Negative symbol) — press to range out.6. + (Plus/Positive symbol) — press to range in.7. Active — press to switch the active pane, or

to switch the active multifunction display (inmultiple display systems).

8. Waypoint / MOB — press and release toaccess the waypoint options. Press again toplace a waypoint. Press and hold to place aMan Overboard (MOB) marker at your currentposition.

9. Standby (Auto) — press to disengageintegrated autopilot, press and hold to activateAuto mode on integrated autopilot.

10. Power — see table below:Configura-tion

DisplayState

Momentarypress

Press andhold

Off / Standby * Power on —1Multifunctiondisplay On Open

Shortcutspage

Power off/ put intoStandby

All displaysOff or inStandby

* Power onall displays

—

All displaysOn

OpenShortcutspage onactive display

Power downall displays

Multiplemultifunctiondisplays

1 DisplayOn and 1display Offor in Standby

OpenShortcutspage onactive display

Power downactive display

Note: * Only applicable to eS and gS Seriesdisplays. a Series, c Series and e Seriesdisplays cannot be powered on using thekeypad.

Note: In a multiple display configuration,where displays are in different states, displaysthat are turned off can only be turned on usingthe Power button on the display.

11. Direction of Joystick Up.

26

6.2 Pairing the keypadEach keypad can be paired with multiple MFDs andmultiple keypads can be connected to the samesystem.With the keypad connected to the MFD:1. Select External Keypad from the External

Devices menu: homescreen > Set-up > SystemSettings > External Devices > ExternalKeypad.

2. Select Pair Keypad.3. Press any button on the external keypad.4. From the pop-up message select the orientation

of the keypad.

Either landscape or portrait orientations areavailable.

The keypad is now paired.

Switching the active pane or displayusing the keypadThe Active button is used to switch the active paneon a multi application page and / or to switch theactive display.With multiple displays connected and / or a multipleapplication page displayed:

Cycle sequence

1. Press the Active button to enter switch mode.2. Use the Rotary control to cycle through the

available panes and / or displays.

The keypad will cycle through displays in theorder in which they were paired. On multiapplication pages the + and - buttons can beused to switch the active application between fulland splitscreen.

3. Press the Back button or the Active button toexit switch mode.

Unpairing the keypadThe keypad can be unpaired from an individualdisplay.1. Select External Keypad from the External

Devices menu: homescreen > Set-up > SystemSettings > External Devices > ExternalKeypad.

2. Select Clear Pairings.3. Select Yes to unpair the keypad with the display.

Unpairing from all displaysThe keypad can be unpaired from all displaysfollowing the steps below.1. Press and hold the Range In and Range Out

buttons simultaneously for approximately 6seconds.

The keypad will sound a triple beep to signify it isnow unpaired.

Determining the active displayYou can determine which display is currently active.1. Press the Active button.

The Active pop-up is displayed on the screen orpane that is active.

2. Press the Active button again to close the Activepop-up.The active display remains the same.

Operation 27

28

Chapter 7: System checks and troubleshooting

Chapter contents• 7.1 Keypad status on page 30• 7.2 PoE troubleshooting on page 30• 7.3 Power up troubleshooting on page 31

System checks and troubleshooting 29

7.1 Keypad statusThe keypad is backlit with LEDs. The LEDs are usedto identify the status of the keypad.

StatusUniControllerLED ring Keypad backlight

Keypad poweredoff or not paired

Off Off

Keypad is poweredon and paired

On On

MFD is inPowerSave mode

Flashing Off

The LED and keypad backlight brightness willchange to match the paired MFD brightness.

7.2 PoE troubleshootingIf you are experiencing connection issues withthe remote keypad when powering the device viaPoE, consider using the keypad’s dedicated powerconnector to supply the power to the device.Possible causes for connection issues are:• Low or inconsistent voltage at the power supplyto the MFD.

• Inadequate power or data cabling.• If multiple devices are powered via PoE from theMFD, the power allocation for the PoE devicesmay be too high, either because there are toomany device connected, or the total powerconsumption exceeds the supported allocation.Refer to the Power over Ethernet (PoE) topic inthe MFD’s Installation instructions document formore information on the PoE power allocation.

30

7.3 Power up troubleshootingProblems at power up and their possible causes and solutions are described here.

Product does not turn on or keeps turning offPossible causes Possible solutionsBlown fuse / tripped breaker 1. Check condition of relevant fuses and breakers and connections, replace

if necessary (Refer to the Technical Specification section of your product’sinstallation instructions for fuse ratings.)

2. If fuse keeps blowing check for cable damage, broken connector pins orincorrect wiring.

Poor / damaged / insecure power supplycable / connections

1. Check that the power cable connector is fully inserted into the unit and locked inposition.

2. Check the power supply cable and connectors for signs of damage or corrosion,replace if necessary.

3. With the unit turned on, try flexing the power cable near to the display connectorto see if this causes the unit to re-boot/loose power, replace if necessary.

4. Check the vessel’s battery voltage, the condition of the battery terminals andpower supply cables, ensuring connections are secure, clean and free fromcorrosion, replace if necessary.

5. With the product under load, using a multi-meter, check for high voltage dropacross all connectors/fuses etc, replace if necessary.

Incorrect power connection The power supply may be wired incorrectly, ensure the installation instructions havebeen followed.

Power source insufficient With the product under load, using a multi-meter, check the power supply voltage asclose to the unit as possible to establish actual voltage when the current is flowing.(Refer to the Technical Specification section of your product’s installation instructionsfor power supply requirements.)

Product will not boot up (re-boot loop)Possible causes Possible solutionsPower supply and connection See possible solutions from ‘Products does not turn on or keeps turning off’ above.

Software corruption 1. In the unlikely event that the products software has become corrupted please tryre-flashing the latest software from the Raymarine website.

2. On display products, as a last resort, you can try to perform a ‘Power on Reset’,however this will delete all settings/presets and user data (such as waypointsand tracks) and revert the unit back to factory defaults.

System checks and troubleshooting 31

32

Chapter 8: Maintenance

Chapter contents• 8.1 Service and maintenance on page 34• 8.2 Routine equipment checks on page 34• 8.3 Product cleaning on page 35

Maintenance 33

8.1 Service and maintenanceThis product contains no user serviceablecomponents. Please refer all maintenanceand repair to authorized Raymarine dealers.Unauthorized repair may affect your warranty.

8.2 Routine equipment checksRaymarine strongly recommends that you completea number of routine checks to ensure the correct andreliable operation of your equipment.Complete the following checks on a regular basis:• Examine all cables for signs of damage or wearand tear.

• Check that all cables are securely connected.

34

8.3 Product cleaningBest cleaning practices.

When cleaning products:• Lightly rinse or flush with clean, cool fresh water.• If your product has a display screen, do NOT wipethe screen with a dry cloth, as this could scratchthe screen coating.

• Do NOT use: abrasive, acidic, ammonia, solventof chemical based cleaning products.

• Do NOT use a jet wash.

Maintenance 35

36

Chapter 9: Technical specification

Chapter contents• 9.1 Technical specification on page 38• 9.2 Compliance on page 38

Technical specification 37

9.1 Technical specificationPower specificationPoE class Class 1Nominal supplyvoltage

• PoE: 48 V dc• Alternate power: 12 V / 24 V dc

Operatingvoltage range

• PoE: 44 V to 57 V dc• Alternate power: 9 V to 32 V dc

Powerconsumption

4 W Max with full keypad illumination

Environmental specificationOperatingtemperature

-25 ºC to +55 ºC (-13 ºF to 131 ºF)

Storagetemperature

-30 ºC to +70 ºC (-22 ºF to 158 ºF)

Relative humidity Maximum 93%Waterproof rating IPx6 & IPx7

Wired connectionsNetwork / PoE 1 x RayNet 10/100 Mb/s connectorAlternate power 1 x Power connector (SeaTalkng® style

connector)

9.2 ComplianceThe product has been tested to the relevant sectionsof the standards listed below.Ethernet/PoE • IEEE 802.3

• IEEE 802.3af (PoE)EMC • EN60945

38

Chapter 10: Technical support

Chapter contents• 10.1 Raymarine product support and servicing on page 40• 10.2 Learning resources on page 41

Technical support 39

10.1 Raymarine product supportand servicingRaymarine provides a comprehensive productsupport service, as well as warranty, service, andrepairs. You can access these services through theRaymarine website, telephone, and e-mail.

Product informationIf you need to request service or support, pleasehave the following information to hand:• Product name.• Product identity.• Serial number.• Software application version.• System diagrams.You can obtain this product information using themenus within your product.

Servicing and warrantyRaymarine offers dedicated service departments forwarranty, service, and repairs.Don’t forget to visit the Raymarine website toregister your product for extended warranty benefits:http://www.raymarine.co.uk/display/?id=788.Region Tele-

phoneE-mail

UnitedKingdom (UK),EMEA, andAsia Pacific

+44(0)1329246 932

emea.service@raymarine.com

United States(US)

+1 (603)324 7900

rm-usrepair@flir.com

Web supportPlease visit the “Support” area of the Raymarinewebsite for:• Manuals and Documents — http://www.rayma-rine.com/manuals

• FAQ / Knowledgebase — http://www.rayma-rine.com/knowledgebase

• Technical support forum — http://forum.rayma-rine.com

• Software updates — http://www.rayma-rine.com/software

Telephone and e-mail supportRegion Tele-

phoneE-mail

United Kingdom(UK), EMEA,and Asia Pacific

+44(0)1329246 777

support.uk@raymarine.com

United States(US)

+1 (603)324 7900(Toll-free:+800 5395539)

support@raymarine.com

Region Tele-phone

E-mail

Australia andNew Zealand

+61 289770300

aus.support@raymarine.com(Raymarine subsidiary)

France +33 (0)146 49 7230

support.fr@raymarine.com(Raymarine subsidiary)

Germany +49(0)40 237808 0

support.de@raymarine.com(Raymarine subsidiary)

Italy +39 0299451001

support.it@raymarine.com(Raymarine subsidiary)

Spain +34 962965 102

sat@azimut.es(Authorized Raymarinedistributor)

Netherlands +31(0)263614 905

support.nl@raymarine.com(Raymarine subsidiary)

Sweden +46(0)317633 670

support.se@raymarine.com(Raymarine subsidiary)

Finland +358(0)207619 937

support.fi@raymarine.com(Raymarine subsidiary)

Norway +47 69264 600

support.no@raymarine.com(Raymarine subsidiary)

Denmark +45 437164 64

support.dk@raymarine.com(Raymarine subsidiary)

Russia +7 495788 0508

info@mikstmarine.ru(Authorized Raymarinedistributor)

Viewing product informationWith your MFD Homescreen displayed:1. Select Set-up.2. Select Maintenance.3. Select Diagnostics.4. Select Select Device.5. Select the relevant product from the list.The Diagnostics page is displayed.

40

10.2 Learning resourcesRaymarine has produced a range of learningresources to help you get the most out of yourproducts.

Video tutorialsRaymarine official channel onYouTube:

• http://www.youtube.com/u-ser/RaymarineInc

Video Gallery:

• http://www.rayma-rine.co.uk/view/?id=2679

Product Support videos:

• http://www.rayma-rine.co.uk/view/?id=4952

Note:• Viewing the videos requires a device with anInternet connection.

• Some videos are only available in English.

Training coursesRaymarine regularly runs a range of in-depth trainingcourses to help you make the most of your products.Visit the Training section of the Raymarine websitefor more information:• http://www.raymarine.co.uk/view/?id=2372

FAQs and Knowledge BaseRaymarine has produced an extensive set of FAQsand a Knowledge Base to help you find moreinformation and troubleshoot any issues.• http://www.raymarine.co.uk/knowledgebase/

Technical support forumYou can use the Technical support forum to aska technical question about a Raymarine productor to find out how other customers are usingtheir Raymarine equipment. The resource isregularly updated with contributions from Raymarinecustomers and staff:• http://forum.raymarine.com

Technical support 41

42

Chapter 11: Spares and accessories

Chapter contents• 11.1 Keypad spares and accessories on page 44

Spares and accessories 43

11.1 Keypad spares and accessoriesSparesItem Part numberPortrait keypad mat spare R70509Landscape keypad mat spare R70508

AccessoriesItem Part numberRight angled 2 m (6.6 ft)power cable

A06070

Straight 2 m (6.6 ft) powercable

A06049

44

RayNet to RayNet cables and connectors

Description Typical use Quantity1 Standard RayNet connection cable

with a RayNet (female) socket on bothends.

Suitable for connecting all RayNet equipment directly toLightHouse multifunction displays featuring a RayNetconnector. Can also be used to connect RayNet equipmentvia a RayNet network switch (e.g. HS5).

1

2 RayNet cable puller (5 pack). These “handles” securely attach to the twist-lock on RayNetcables, enabling you to pull the cables through conduits andother obstacles.

5

3 RayNet to RayNet right-angle coupler/ adapter.

Suitable for connecting RayNet cables at 90° (right angle) todevices, for installations where space is limited. For example,use this adapter to connect a RayNet cable to a multifunctiondisplay when there is not enough space behind the display forthe usual cable bend radius required by a standard RayNetcable. This adapter features a RayNet (female) socket at oneend, and a RayNet (male) plug at the other end.

1

4 Adapter cable with a RayNet (male)plug on both ends.

Suitable for joining (female) RayNet cables together forlonger cable runs.

1

Spares and accessories 45

RayNet to RJ45 adapter cables

Description Typical use Quantity1 Adapter cable with a RayNet (female)

socket on one end, and a waterproof(female) socket on the other endaccepting the following cables with anRJ45 SeaTalkhs waterproof locking(male) plug:

• A62245 (1.5 m).• A62246 (15 m).

A typical use for this adapter cable is to connect a DSM300sonar module to a LightHouse MFD, using all-waterproofcable connections. This adapter cable will also accept thefollowing RJ45 SeaTalkhs cables, although the RJ45 plugthat connects at the equipment end (e.g. DSM300) will NOTbe waterproof:

• E55049 (1.5 m).• E55050 (5 m).• E55051 (10 m).• A62135 (15 m).• E55052 (20 m).

1

2 Adapter cable with a RayNet (female)socket on one end, and a waterproof(female) RJ45 socket on the otherend, along with a locking gland for awatertight fit.

Directly connect a Raymarine radar scanner with an RJ45SeaTalkhs (male) cable to a RayNet network switch (e.g.HS5) or LightHouse MFD.

1

3 Adapter cable with a RayNet (male)plug on one end, and an RJ45SeaTalkhs waterproof (male) plug onthe other end.

Connect a legacy G-Series GPM-400, C-SeriesWidescreenor E-Series Widescreen MFD to a Raymarine radar scannersupplied with a RayNet power / data cable.

1

4 Adapter cable with a RayNet (female)socket on one end, and an RJ45SeaTalkhs waterproof (male) plug onthe other end.

Connect a legacy G-Series GPM-400, C-SeriesWidescreenor E-Series Widescreen MFD to a RayNet network switch(e.g. the HS5).

1

5 Adapter cable with a RayNet (female)socket on one end, and an RJ45SeaTalkhs (female) socket on theother end.

Connect a LightHouse MFD to a legacy SR6 switch /weather receiver or a legacy 8–port SeaTalkhs networkswitch. Another common use for the cable is in conjunctionwith a crossover coupler (E55060 or R32142) to connectRaymarine products with an RJ45 connection (e.g. radarscanner, thermal camera or DSM300) to a LightHouse MFDor RayNet network switch (e.g. the HS5).

1

46

Index

AAccessories ........................................................... 44Active display......................................................... 27

BBacklight ................................................................ 30Box contents, See Parts suppliedButtons, See Controls

CCable bend radius ................................................. 16Cable protection .................................................... 16Cable routing ......................................................... 16Cleaning ................................................................ 35Compatible MFDs.................................................. 10Connections........................................................... 17Connectors, See ConnectionsContact details....................................................... 40Controls ................................................................. 26

DDiagnostics ............................................................ 30

EElectromagnetic Compatibility ................................. 7EMC, See Electromagnetic CompatibilityEnvironmental specification................................... 38

FFlush mounting...................................................... 22

KKeypad mat fitting.................................................. 23keypad mat removal .............................................. 22

LLED diagnostics..................................................... 30

MMaintenance.......................................................... 34

NNetwork connections ............................................. 18Network examples ................................................. 18

PPairing ................................................................... 27Parts supplied........................................................ 12PoE connection ..................................................... 17PoE specification................................................... 38Power connection.................................................. 17

Power consumption............................................... 38Power specification................................................ 38Product dimensions............................................... 14Product documentation.......................................... 10Product information ............................................... 10Product support ..................................................... 40

RRoutine checks...................................................... 34

SSecuring cables..................................................... 16Service Center....................................................... 40Servicing................................................................ 34Software updates................................................... 13Spares ................................................................... 44Status .................................................................... 30Strain relief, See Cable protectionSurface mounting .................................................. 23System examples .................................................. 18

TTechnical support................................................... 40Temperature range ................................................ 38Tools ...................................................................... 13Troubleshooting..................................................... 30Typical systems ..................................................... 18

UUniController LED.................................................. 30Unpairing ............................................................... 27Upgrading, See Software updatesUser interface ........................................................ 26

WWarranty ................................................................ 40Water ingress ........................................................ 38

Spares and accessories 49

Raymarine UK Limited, Marine House, Cartwright Drive, Fareham, PO15 5RJ. United Kingdom.Tel: +44 (0)1329 246 700

www.raymarine.com