Installation Instructions 30 Electric, 30 Induction Range ... · Installation Instructions 30"...
Transcript of Installation Instructions 30 Electric, 30 Induction Range ... · Installation Instructions 30"...
Installation Instructions
30" Electric, 30" Induction Range
30", 36" All Gas Range
30", 36", 48" Dual Fuel Range
To prevent accidents and damage to the range, you must read all
instructions supplied before installing or using the appliance.
en - US, CA M.-Nr. 09 898 161
IMPORTANT SAFETY INSTRUCTIONS
2
WARNING
Children and adults can tip over the range if has not beensecured. This may lead to fatal injuries.
This range must be secured and connected using the anti-tipdevice according to the installation instructions.
If you have moved the range, slide the locking latch onto the anti-tip device until you feel it lock into place.
Do not use the range if the anti-tip device has not been properlyinstalled and engaged.
Failure to observe the information contained in the installationinstructions can lead to serious or fatal injuries for children andadults.
All ranges can tip
Injury to persons
could result
Install anti-tip devices
packed with range
See installation
instructions
WARNING
IMPORTANT SAFETY INSTRUCTIONS
3
WARNING: If the information in this manual is not followed exactly, a fire orexplosion may result causing property damage, personal injury, or death.
– Do not use or store gasoline or other combustible liquids or vapors in thevicinity of this or any other appliance.
– WHAT TO DO IF YOU SMELL GAS
– Do not try to light any appliance.
– Do not touch any electric switches.
– Do not use any phones inside your building.
– Immediately call your gas supplier from a neighbor's phone. Follow the gassupplier's instructions.
– If you are unable to reach your gas provider, call the fire department.
– Installation and service must be performed by a qualified installer, qualifiedservice agency or your gas provider.(In Massachusetts, installation must be performed by a licensed installer / gasfitter.)
– Note to the installer:Please give these installation instructions to the consumer for the localelectrical/gas inspector.
® ®
Contents
4
IMPORTANT SAFETY INSTRUCTIONS ................................................................. 2
IMPORTANT SAFETY INSTRUCTIONS ................................................................. 6
Notes on installation ............................................................................................ 14Model numbers ..................................................................................................... 14Data plate .............................................................................................................. 14Distance to the range hood.................................................................................... 14Items included with this range ............................................................................... 14
Toe-kick and drip tray ....................................................................................... 14Installation of the toe-kick................................................................................. 14Installation of the drip tray ................................................................................ 15Assembling the grill........................................................................................... 16
Optional accessories ............................................................................................. 17RBGAG All Gas Backguard/RBGDF Dual Fuel Backguard............................... 17RBS Backsplash ............................................................................................... 19XKM 3000 W Remote Vision............................................................................. 19
Required connections ............................................................................................ 21
Electric Range dimensions ................................................................................. 22HR 1421; HR 1622 ................................................................................................. 22Detailed views of HR 1421..................................................................................... 24Detailed views of HR 1622..................................................................................... 28
All Gas Range dimensions .................................................................................. 32All Gas Range HR 11xx with Standard Burner Configuration................................ 32Detailed views of HR 1124..................................................................................... 40Detailed views of HR 1134..................................................................................... 44Detailed views of HR 1135..................................................................................... 48Detailed views of HR 1136..................................................................................... 52
Dual Fuel Range dimensions .............................................................................. 56Dual Fuel Range HR 19xx with Standard Burner Configuration ............................ 56Detailed views of HR 1924..................................................................................... 66Detailed views of HR 1934..................................................................................... 70Detailed views of HR 1935..................................................................................... 74Detailed views of HR 1936..................................................................................... 78Detailed views of HR 1954..................................................................................... 82Detailed views of HR 1955..................................................................................... 86Detailed views of HR 1956..................................................................................... 90
Contents
5
Anti-tip device ...................................................................................................... 94Before installation .................................................................................................. 94Checking the installation space ............................................................................. 95Included accessories ............................................................................................. 95Installation dimensions of locking bolt................................................................... 96Installing the range with the anti-tip device ........................................................... 96Disconnecting the range from the anti-tip device.................................................. 99
Electrical connection ......................................................................................... 100Data plate........................................................................................................ 101
Plumbing ............................................................................................................. 103Notes on connecting to the water supply ............................................................ 103Attach the stainless steel hose to the range. ....................................................... 104Connecting to the water supply........................................................................... 104
Gas connection .................................................................................................. 105
Burner ratings of Standard Burner Configuration .......................................... 107Burner ratings for HR 1124 .................................................................................. 107Burner ratings for HR 1134 .................................................................................. 108Burner ratings for HR 1135 .................................................................................. 109Burner ratings for HR 1136 .................................................................................. 110Burner ratings for HR 1924 .................................................................................. 110Burner ratings for HR 1934 .................................................................................. 111Burner ratings for HR 1935 .................................................................................. 111Burner ratings for HR 1936 .................................................................................. 112Burner ratings for HR 1954 .................................................................................. 112Burner ratings for HR 1955 .................................................................................. 113Burner ratings for HR 1956 .................................................................................. 113
Caring for the environment ............................................................................... 115
IMPORTANT SAFETY INSTRUCTIONS
6
When using the appliance, follow basic safety precautions, including the
following:
Read all instructions before installation and use of the range to prevent
accidents and machine damage.
This range complies with current safety requirements. However,improper use of the appliance can result in personal injury ordamage to property.
Please read the installation instructions carefully before installingand connecting the appliance. Read the operating instructions before using the range for the firsttime. To prevent accidents and damage to the appliance, alwaysobserve both the installation instructions and operatinginstructions. Both documents contain important information aboutinstallation, safety, use and maintenance.Miele cannot be held liable for damage occurring as a result ofnon-compliance with the instructions.
Keep these installation instructions and operating instructions in asafe place and pass them on to any future owner.
IMPORTANT SAFETY INSTRUCTIONS
7
Use
This range is intended for domestic use and use in other similarenvironments.
This appliance is not intended for outdoor use.
Use the range exclusively under normal domestic conditions:
– Use the oven for baking, roasting, broiling, defrosting, canningand drying food.
– Use the stovetop to prepare food and keep it warm.
Any other use is not permitted.
Risk of Fire! Do not use this oven to store or dry combustiblematerials.
Persons who lack physical, sensory or mental abilities, orexperience with the appliance should not use it without supervisionor instruction by a responsible person.
IMPORTANT SAFETY INSTRUCTIONS
8
Children
Children must be kept away from the range unless constantlysupervised.
Please supervise any children in the vicinity of the range and donot let them play with the appliance.
Burn hazard from improper use! Do not allow children to operatethe oven.
Danger of suffocation! Ensure that any plastic wrappings, bags,etc. are disposed of safely and kept out of the reach of children.
Burn hazard! Keep the spaces above and behind the range clear of any items thatcould draw the attention of children. Otherwise, they can be temptedinto climbing onto the appliance.
Danger of injury. Never allow children to hang or lean on any partof the appliance.
IMPORTANT SAFETY INSTRUCTIONS
9
Technical safety
Installation, repair and maintenance work should be performed bya Miele authorized service technician in accordance with nationaland local safety regulations and the provided installationinstructions. Contact Miele’s Technical Service Department forexamination, repair or adjustment. Repairs and other work byunauthorized persons could be dangerous and may void thewarranty.
Do not carry or lift the range by the oven door handle or thecontrol panel!
Check whether the anti-tip device is properly installed and lockedinto place (see "Anti-tip device"):
– The anti-tip device must be fastened to the floor or wall withsuitable screws.
– You must be able to feel that the locking latch is engaged in thebolt of the anti-tip device.
Slide the range's locking latch into place on the anti-tip device.The locking latch must be noticeably engaged with the bolt of theanti-tip bracket.
A damaged range can be dangerous. Always check for visiblesigns of damage. Never use a damaged appliance.
Reliable and safe operation of the range can only be guaranteed ifit is connected to the public power supply.
The electrical safety of the range can only be guaranteed when itis properly grounded. Compliance with this essential safetyrequirement is absolutely mandatory. If in any doubt, please havethe building's wiring system inspected by a qualified electrician.
To avoid damaging the range, make sure that the connection data(voltage and frequency) on the data plate correspond to thebuilding's power supply before connecting the appliance.When in doubt, consult a qualified electrician.
IMPORTANT SAFETY INSTRUCTIONS
10
During installation, maintenance and repair work, e.g. if the ovenlighting is broken (see "Frequently asked questions"), the range mustbe completely disconnected from the household electricity supply.The gas supply must be shut off. Ensure that this is the case by:
– removing the fuse,
– "tripping" the circuit breaker, or
– unplugging the unit. Pull the plug not the cord.
– Shut off the gas supply and, if necessary, disconnect the rangefrom the gas line. Installation and maintenance of the gasconnection must be performed by qualified installers, serviceagencies or gas providers.
Do not use a power strip or extension cord to connect the rangeto electricity. These are a fire hazard and do not guarantee therequired level of appliance safety.
Any contact with live connections or tampering with the electricalor mechanical components of the range will endanger your safetyand may lead to appliance malfunctions.Do not open the appliance housing under any circumstances.
This appliance must not be installed and operated in mobileinstallations (e.g. on a ship).
Any repairs not performed by a Miele authorized servicetechnician will void the warranty.
Defective components should be replaced by Miele original partsonly. Only with these parts can the manufacturer guarantee thesafety of the appliance.
Risk of electric shock! If the ceramic surface of the stovetop isdefective or chipped, cracked or broken in any way, immediatelyswitch the stovetop off and do not continue to use it. Disconnect therange from the power supply and contact Miele Technical Service.
IMPORTANT SAFETY INSTRUCTIONS
11
In order for the range to function properly, it requires an adequatesupply of cool air. Ensure that the air flow is not impaired. Also besure that the cool air supply is not excessively heated by other heatsources (e.g. solid fuel stoves).
If the range is installed behind a cabinet door, do not close thedoor while the appliance is in operation. Heat and moisture can buildup behind the closed door and cause damage to the range and tothe surrounding cabinets and flooring. Do not close the door untilthe appliance has completely cooled down.
Do not install kitchen cabinets above the range, since reachingover a hot stovetop to access the cabinets can result in burns. If it isnecessary to install cabinets, you can reduce the risk of burns byinstalling a range hood that extends at least 4 3/4" (12 cm) past thebottom of the cabinets.
The water shutoff valve must be accessible after the range hasbeen installed.
The integrated Waterproof System offers protection against waterdamage if the following conditions are met:
– The range is properly installed (connected to electric and watersupply).
– The range is repaired immediately whenever damage is detected.
– The water supply is shut off during extended periods of non-use(e.g. vacation).
Hard water, water containing minerals and water from reverseosmosis filtering systems can damage the range. Only use filtered,softened and demineralized water from the building's plumbing tosupply the range.
IMPORTANT SAFETY INSTRUCTIONS
12
Preparing your appliance for an extended vacation
If you elect to turn off the water to your home for an extendedperiod of time, please note that this may not be enough to reducethe risk of a leak. To be completely safe, you must turn off the watersupply to each individual appliance.
IMPORTANT SAFETY INSTRUCTIONS
13
Cleaning and care
Do not use a steam cleaner to clean the range.The steam may reach electrical components and cause a shortcircuit.
Only clean parts listed in these Operating and InstallationInstructions.
Scratches on the door glass can cause the glass to break.Do not use abrasive cleaners, hard sponges, brushes or sharp metaltools to clean the door glass.
The shelf runners can be removed for cleaning purposes (see"Cleaning and care"). Ensure they are correctly fitted after cleaningand never operate the oven without the shelf runners inserted.
There is a seal around the oven interior which seals the inside ofthe door. Take care not to rub, damage or move the gasket.
Do not use oven cleaners. Commercial oven cleaners or ovenliners of any kind should not be used in or around any part of theoven.
Debris should be removed before running the Self Clean program.If not removed this debris can smoke causing the self-cleaningprogram to turn itself off.
SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY
Notes on installation
14
Model numbers
A list of the ovens described in theseoperating instructions can be found onthe back page.
Data plate
The data plate is behind the toe-kick.The toe-kick cover is attached to thebase of the range by magnets so it canbe removed and put back again easily.
There you can find the model number,the serial number and the connectiondata (voltage/frequency/maximum ratedload) for your range.
Have this information available whencontacting Miele Technical Service.
Distance to the range hood
The minimum clearance between theappliance and a range hood above willbe listed by the hood manufacturer.
If there is more than one applianceinstalled below the range hood, eachwith a different safety clearance, thelargest clearance must be used.
Items included with this range
The range is supplied with:
– Installation Instructions,
– Multiple operating instructions(depending on model) for:
– Electric Range
– Induction Range
– Convection Oven
– Gas Cooktop
– Gas Convection Oven
– Speed Oven
– Warming Drawer
– an anti-tip device including screwsfor fastening the range,
– various accessories.
Toe-kick and drip tray
30" and 36" range
The components are located in thepackaging of the range.
48" range
The components are already installed.
Installation of the toe-kick
The toe-kick has sheet metal lugs andmagnets by means of which it can bepositioned and attached to the baseof the range.
Position the toe-kick in such a waythat the sheet metal lugs are facingthe provided holes in the base.
Push the toe-kick onto the base ofthe range until it audibly locks intoplace.
Notes on installation
15
Installation of the drip tray
The drip tray covers the gap betweenthe oven cavity and the door.
Open the oven door.
Lay the drip tray over the gapbetween the oven cavity and thedoor.
Close the oven door.
Notes on installation
16
Assembling the grill
Burn hazard!The burners must be turned off andallowed to cool completely.
Risk of injury!The cast-iron grill is heavy.Carry the grill carefully and place itsecurely on a soft base so that it liesflat.
3
1
2
Grill Radiant plate Frame
Using a soft sponge, clean radiantplate with a solution of warm waterand a small amount of liquid dishsoap. Dry the parts thoroughly aftercleaning.
Remove the grill from the gascooktop.
Place the radiant plate on top ofthe frame .
Place the grill into position.
Cleaning and care
Tip: All parts can be disassembled inthe reverse order. You can also removethe frame for cleaning.
Notes on installation
17
Optional accessories
All accessories and cleaning productslisted in these instructions are designedto be used with the Miele range.
These can be ordered from the Mielewebsite (see end of this booklet forcontact details).
When ordering, please have your modelnumber available.
RBGAG All Gas Backguard/RBGDF
Dual Fuel Backguard
Depending on the model, you canexchange the existing island trim ofyour appliance for a larger rangebackguard. The backguard is availablein the following heights: 12" (305 mm)and 20" (508 mm).
Installing the RBGDF Dual Fuel
Backguard
The rear of the range must beaccessible.
Install the backguard before installingthe anti-tip device and connecting ofthe range.
Loosen the screws of the island trim.
Pull back the island trim slightly untilit can be removed.
The backguard can be installed inreverse order.
Installing the RBGAG All Gas
Backguard
The rear of the range must beaccessible.
Install the backguard before installingthe anti-tip device and connecting therange.
Loosen the screws of the island trim.
Pull back the island trim slightly untilit can be removed.
Extender Air ducts
Insert one extender onto each ofthe left and right air ducts .
Screw the extenders into placewith 2 screws each.
Notes on installation
18
1 2 3
Backguard Rear panel backguard Inside panel
Place the backguard face down ona soft surface to avoid scratching.The lower edge should line up withthe edge of the table, so that thebackguard lies flat.
Loosen the screws on the back ofbackguard.
Remove the rear panel and theinner panel .
1
2
Backguard Range
Slide the backguard from aboveon the air duct extenders.
Notes on installation
19
Once the backguard is placed on therange push the backguardbackwards.
Install the inner panel and the rearpanel on the backguard using thescrews provided.
Install the backguard on the rangeusing the screws provided.
12" Backguard
20" Backguard
RBS Backsplash
The backsplash is intended forinstallation to a Miele Range Hood(DAR model). Observe the installationinstructions of the Miele Range Hood.
XKM 3000 W Remote Vision
Depending on the model, the rangemaybe compatible withRemoteVisionTM.
In order to use the RemoteVisionTM
monitoring service, you will require aXKM 3000 W Communication Module.Refer to the Operating and InstallationInstructions of the Miele XKM 3000 WCommunication Module.
Notes on installation
20
Do not carry or lift the range by the oven door handle or the control panel!
The range is heavy.Due to the size and weight of the appliance, installation should be performedby two people.
The net weight of the range with accessories is as follows:
Model Width Net weight incl.
accessories:
HR 1421
HR 1622
HR 112x
HR 192x
29 15/16"
(760 mm)
approx. 307 lbs (140 kg)
HR 113x
HR 193x
35 15/16"
(913 mm)
approx. 405 lbs (180 kg)
HR 195x 47 15/16"
(1218 mm)
approx. 573 lbs (260 kg)
Notes on installation
21
Installation location
This appliance is not intended for outdoor use.Ranges with a connection to the water supply should not be installed in roomswhere there is a risk of freezing temperatures.
The floor of the space where the appliance is to be installed must be flat, level andmade of a strong, rigid material.
Because the range is heavy and requires attachment of the anti-tip devicesupplied, the surface must be able to fully bear the load of the appliance. Ifnecessary, seek the advice of an architect or construction expert.
Ventilation
The air intake and outlet openings must not be covered or blocked in any way.They should be dusted on a regular basis.
Required connections
Model Electrical
connection
Gas connection Plumbing
HR 1421 X – –
HR 1622 X – X
HR 112x
HR 113x
X X –
HR 192x
HR 193x
HR 195x
X X X
X Connection required– Connection not provided
Electric Range dimensions
22
HR 1421; HR 1622
2
, , The shaded area represents the installation area for the connections: E = Electrical connection, W = Water connection (only HR 1622)
Electric Range dimensions
23
HR 1421; HR 1622
Position Dimensions Description
13" (330 mm) Maximum depth of top cabinet
18" (547 mm) Minimum distance to bottom edge of top cabinet
35 1/2"–37"(901–940 mm)
Distance from the floor to cooktop surface
Min. 30"(762 mm)
Width of cabinet opening
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
or 24" (609 mm) Minimum distance to a protected combustiblesurface or when a Miele Ventilation Hood isinstalled.
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx.10 13/16"(274 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
From the back side of the cooktop, a 12" (305 mm) minimum distance to the combustiblerear wall above the countertop is required.
Electric Range dimensions
24
Detailed views of HR 1421
Side view of HR 1421
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
Electric Range dimensions
25
Detailed front side view of HR 1421
Electric Range dimensions
26
Front side view of HR 1421(x
)
28 1/8"(7
mm
)
(34m
m)
(43m
m)
(712mm)
20 5/16" (566.65mm)
27 1/4" (692mm)
(-1/16" / -2mm)
13/16"
(20.85mm)
2 9/16"
(65.2mm)
17 1
3/16
"(4
52.2
mm
)22 5/8" (574.6mm)
35 1
/2" -
37"
(901
.7m
m -
939.
8mm
)
1 9/
16"
(40m
m)
8 1/
8"(2
07m
m)
1 5/
16"
1/4"
1 11
/16"
29 15/16" (760mm)
1/8" (3mm)
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
Electric Range dimensions
27
Rear view of HR 1421
E = Electrical connection
Electric Range dimensions
28
Detailed views of HR 1622
Side view of HR 1622
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
Electric Range dimensions
29
Detailed front side view of HR 1622
Electric Range dimensions
30
Front side view of HR 1622(x
)
28 1/8"(7
mm
)
(34m
m)
(43m
m)
(712mm)
20 5/16" (566.65mm)
27 1/4" (692mm)
(-1/16" / -2mm)
13/16"
(20.85mm)
2 9/16"
(65.2mm)
17 1
3/16
"(4
52.2
mm
)22 5/8" (574.6mm)
35 1
/2" -
37"
(901
.7m
m -
939.
8mm
)
1 9/
16"
(40m
m)
8 1/
8"(2
07m
m)
1 5/
16"
1/4"
1 11
/16"
29 15/16" (760mm)
1/8" (3mm)
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
Electric Range dimensions
31
Rear view of HR 1622
E = Electrical connection
W = Water connection
All Gas Range dimensions
32
All Gas Range HR 11xx with Standard Burner Configuration
HR 1124, HR 1134, HR 1135, HR 1136
2
In case of combustible materials, a minimum distance of 6" must be observed on eachside in addition to dimension .
, , The shaded area represents the installation area for the connections: E = Electrical connection, G = Gas connection
Position Dimensions Description
13" (330 mm) Maximum depth of top cabinet
18" (457 mm) Minimum distance to bottom edge of top cabinet
35 1/2"–37"(901–940 mm)
Distance from the floor to cooktop surface
10" (254 mm) Minimum distance to combustible surfaces.
All Gas Range dimensions
33
HR 1124
Position Dimensions Description
Min. 30"(762 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx.10 13/16"(274 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
All Gas Range dimensions
34
HR 1134
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
36" (914 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
All Gas Range dimensions
35
HR 1135, HR 1136
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL or DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
From the back side of the cooktop, a 12" (305 mm) minimum distance to the combustiblerear wall above the countertop is required.
All Gas Range dimensions
37
HR 1124
Position Dimensions Description
Min. 30"(762 mm)
Width of cabinet opening
Please contact Miele Service for more information.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx.10 13/16"(274 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
All Gas Range dimensions
38
HR 1134
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
Please contact Miele Service for more information.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
36" (914 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
All Gas Range dimensions
39
HR 1135, HR 1136
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
Please contact Miele Service for more information.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL or DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
From the back side of the cooktop, a 12" (305 mm) minimum distance to the combustiblerear wall above the countertop is required.
All Gas Range dimensions
40
Detailed views of HR 1124
Side view of HR 1124
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
All Gas Range dimensions
41
Detailed front side view of HR 1124
All Gas Range dimensions
42
Front side view of HR 1124
13/16"
1 5/
16"
1 11
/16"
2 9/16"
1/4"
1 9/
16"
8 1/
8"(x
)35
1/2
" - 3
7"
17 1
3/16
"22 5/8"
27 1/4"
(-1/16" / -2mm)(692mm)
(20.85mm)
(65.2mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
(574.6mm)
(452
.2m
m)
(760mm)
29 15/16"
1/8" (3mm)
(708mm)
27 7/8"
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
All Gas Range dimensions
43
Rear view of HR 1124
E = Electrical connection
G = Gas connection
All Gas Range dimensions
44
Detailed views of HR 1134
Side view of HR 1134
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
All Gas Range dimensions
45
Detailed front side view of HR 1134
All Gas Range dimensions
46
Front side view of HR 1134
1 5/
16"
1 11
/16"
1/4"
1 9/
16"
8 1/
8"
(x)
35 1
/2" -
37"
(65.2mm)
17 1
3/16
"28 5/8"
(864.4mm)
13/16"
35 15/16"1
9/16
"
1 3/4"
27 1/4"
(-1/16" / -2mm)
(452
.2m
m)
2 9/16"
(20.85mm) (40m
m)
(692mm)
(45mm)
(913mm)
(727mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
34"
1/8"
(3mm)
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
All Gas Range dimensions
47
Rear view of HR 1134
E = Electrical connection
G = Gas connection
All Gas Range dimensions
48
Detailed views of HR 1135
Side view of HR 1135
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
All Gas Range dimensions
49
Detailed front side view of HR 1135
All Gas Range dimensions
50
Front side view of HR 1135
1 5/
16"
1 11
/16"
1/4"
1 9/
16"
8 1/
8"
(x)
35 1
/2" -
37"
(65.2mm)
17 1
3/16
"
28 5/8"
(864.4mm)
13/16"
35 15/16"
1 9/
16"
1 3/4"
27 1/4"
(-1/16" / -2mm)
(452
.2m
m)
2 9/16"
(20.85mm) (40m
m)
(692mm)
(45mm)
(913mm)
(727mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
34"
1/8"
(3mm)
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
All Gas Range dimensions
51
Rear view of HR 1135
E = Electrical connection
G = Gas connection
All Gas Range dimensions
52
Detailed views of HR 1136
Side view of HR 1136
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
All Gas Range dimensions
53
Detailed front side view of HR 1136
All Gas Range dimensions
54
Front side view of HR 1136
1 5/
16"
1 11
/16"
1/4"
1 9/
16"
8 1/
8"
(x)
35 1
/2" -
37"
(65.2mm)
17 1
3/16
"
28 5/8"
(864.4mm)
13/16"
35 15/16"
1 9/
16"
1 3/4"
27 1/4"
(-1/16" / -2mm)
(452
.2m
m)
2 9/16"
(20.85mm) (40m
m)
(692mm)
(45mm)
(913mm)
(727mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
34"
1/8"
(3mm)
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
All Gas Range dimensions
55
Rear view of HR 1136
E = Electrical connection
G = Gas connection
Dual Fuel Range dimensions
56
Dual Fuel Range HR 19xx with Standard Burner Configuration
HR 1924, HR 1934, HR 1935, HR 1936, HR 1954, HR 1955, HR 1956
1
In case of combustible materials, a minimum distance of 6" must be observed on eachside in addition to dimension .
, , The shaded area represents the installation area for the connections: E = Electrical connection, W = Water connection, G = Gas connection
Position Dimensions Description
13" (330 mm) Maximum depth of top cabinet
18" (457 mm) Minimum distance to bottom edge of top cabinet
35 1/2"–37"(901–940 mm)
Distance from the floor to cooktop surface
10" (254 mm) Minimum distance to combustible surfaces.
Dual Fuel Range dimensions
57
HR 1924
Position Dimensions Description
Min. 30"(762 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx.10 13/16"(274 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
Dual Fuel Range dimensions
58
HR 1934
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
36" (914 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
Dual Fuel Range dimensions
59
HR 1935, HR 1936
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL or DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
Dual Fuel Range dimensions
60
HR 1954, HR 1955, HR 1956
Position Dimensions Description
Min. 48"(1219 mm)
Width of cabinet opening
6" + + 6"
(150 mm + +150 mm)
If combustible materials are present, an additionalminimum distance of 6" (150 mm) (each side) isrequired. Ensure that the local regulations areobserved.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
36" (914 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 20 1/2"(518 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 3 1/2"(90 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
From the back side of the cooktop, a 12" (305 mm) minimum distance to the combustiblerear wall above the countertop is required.
Dual Fuel Range dimensions
62
HR 1924
Position Dimensions Description
Min. 30"(762 mm)
Width of cabinet opening
Please contact Miele Service for more information.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx.10 13/16"(274 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
Dual Fuel Range dimensions
63
HR 1934
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
Please contact Miele Service for more information.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
36" (914 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL blower).
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
Dual Fuel Range dimensions
64
HR 1935, HR 1936
Position Dimensions Description
Min. 36"(914 mm)
Width of cabinet opening
Please contact Miele Service for more information.
37" (940 mm) Minimum distance between the top of the cookingarea and the bottom of an unprotectedcombustible surface.
30" (762 mm) Minimum distance between the top of the cookingarea and the bottom of the Miele Range Hood(DAR model with DRxB XL or DRxB XXL blower).
For all other Hoods please consult the manufacturer's specificationsfor required distances.
Approx. 13 3/4"(350 mm)
Maximum connection width rightand left
Position ofthe wallsocket
Approx. 4 1/2"(115 mm)
Maximum connection height
Approx. 2 13/16"(72 mm)
Maximum connection depth
Dual Fuel Range dimensions
66
Detailed views of HR 1924
Side view of HR 1924
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
Dual Fuel Range dimensions
67
Detailed front side view of HR 1924
Dual Fuel Range dimensions
68
Front side view of HR 1924
13/16"
1 5/
16"
1 11
/16"
2 9/16"
1/4"
1 9/
16"
8 1/
8"(x
)35
1/2
" - 3
7"
17 1
3/16
"22 5/8"
27 1/4"
(-1/16" / -2mm)(692mm)
(20.85mm)
(65.2mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
(574.6mm)
(452
.2m
m)
(760mm)
29 15/16"
1/8" (3mm)
(708mm)
27 7/8"
(x) = Depending on the appliance height adjustment 5" - 6 1/2"(127 mm - 165.1 mm)
Dual Fuel Range dimensions
69
Rear view of HR 1924
E = Electrical connection
W = Water connection
G = Gas connection
Dual Fuel Range dimensions
70
Detailed views of HR 1934
Side view of HR 1934
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
Dual Fuel Range dimensions
71
Detailed front side view of HR 1934
Dual Fuel Range dimensions
72
Front side view of HR 1934
1 5/
16"
1 11
/16"
1/4"
1 9/
16"
8 1/
8"
(x)
35 1
/2" -
37"
(65.2mm)
17 1
3/16
"
28 5/8"
(864,4mm)
13/16"
35 15/16"
1 9/
16"
1 3/4"
27 1/4"
(-1/16" / -2mm)
(452
.2m
m)
2 9/16"
(20.85mm) (40m
m)
(692mm)
(45mm)
(913mm)
(727mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
34"
1/8"
(3mm)
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
Dual Fuel Range dimensions
73
Rear view of HR 1934
E = Electrical connection
W = Water connection
G = Gas connection
Dual Fuel Range dimensions
74
Detailed views of HR 1935
Side view of HR 1935
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
Dual Fuel Range dimensions
75
Detailed front side view of HR 1935
Dual Fuel Range dimensions
76
Front side view of HR 1935
1 5/
16"
1 11
/16"
1/4"
1 9/
16"
8 1/
8"
(x)
35 1
/2" -
37"
(65.2mm)
17 1
3/16
"
28 5/8"
(864.4mm)
13/16"
35 15/16"
1 9/
16"
1 3/4"
27 1/4"
(-1/16" / -2mm)
(452
.2m
m)
2 9/16"
(20.85mm) (40m
m)
(692mm)
(45mm)
(913mm)
(727mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
34"
1/8"
(3mm)
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
Dual Fuel Range dimensions
77
Rear view of HR 1935
E = Electrical connection
W = Water connection
G = Gas connection
Dual Fuel Range dimensions
78
Detailed views of HR 1936
Side view of HR 1936
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
Dual Fuel Range dimensions
79
Detailed front side view of HR 1936
Dual Fuel Range dimensions
80
Front side view of HR 1936
1 5/
16"
1 11
/16"
1/4"
1 9/
16"
8 1/
8"(x
)
35 1
/2" -
37"
(65.2mm)
17 1
3/16
"
28 5/8"
(864.4mm)
13/16"
35 15/16"
1 9/
16"
1 3/4"
27 1/4"
(-1/16" / -2mm)
(452
.2m
m)
2 9/16"
(20.85mm) (40m
m)
(692mm)
(45mm)
(913mm)
(727mm)
(7m
m)
(34m
m)
(40m
m)
(207
mm
)
(43m
m)
(901
.7m
m -
939.
8mm
)
34"
1/8"
(3mm)
(x) = Depending on the appliance height adjustment: 5" - 6 1/2 "(127 mm - 165.1 mm)
Dual Fuel Range dimensions
81
Rear view of HR 1936
E = Electrical connection
W = Water connection
G = Gas connection
Dual Fuel Range dimensions
82
Detailed views of HR 1954
Side view of HR 1954
(x)
8 1/
8"
35 1
/2 -
37"
(901
.7 -
939.
8mm
)
37 1
/16"
- 38
9/1
6"
(941
.7 -
979.
8mm
)
24 15/16" (633mm)
27 1/4" (692mm)
28 15/16" (734.4mm)
(207
mm
)
15/16" (24.3mm)
44" (1114mm)
(x) = Depending on the appliance height adjustment: 4" - 5 1/2 "(101.6 mm - 139.7 mm)
Dual Fuel Range dimensions
83
Detailed front side view of HR 1954
Dual Fuel Range dimensions
84
Front side view of HR 1954
2 9/16"
(65.2mm)
3/4"(19mm)
1 5/
16"
1/4"
(x)
(7m
m)
(34m
m)
13 3
/8"
8 1/
8"(2
07m
m)
1 9/
16"
(40m
m)
22 1/4" (564.5mm)
3 5/8"
3 5/8"(92.7mm)
47 15/16" (1218mm)
(1158.4mm)
45 5/8"
1 9/
16"
(40m
m)
27 1/4"
(-1/16" / -2mm)(692mm)
1 3/4"
(45mm)
18 1
1/16
"(4
73.9
mm
)
(92.7mm)
(43m
m)
1 11
/16"
27 1
/2"
(340
.5m
m)
(698
.9m
m)
35 1
/2 -
37"
(901
.7 -
939.
8mm
)
(3mm)
1/8"
(x) = Depending on the appliance height adjustment: 4" - 5 1/2 "(101.6 mm - 139.7 mm)
Dual Fuel Range dimensions
85
Rear view of HR 1954
E = Electrical connection
W = Water connection
G = Gas connection
Dual Fuel Range dimensions
86
Detailed views of HR 1955
Side view of HR 1955
(x)
8 1/
8"
35 1
/2 -
37"
(901
.7 -
939.
8mm
)
37 1
/16"
- 38
9/1
6"
(941
.7 -
979.
8mm
)
24 15/16" (633mm)
27 1/4" (692mm)
28 15/16" (734.4mm)
(207
mm
)
15/16" (24.3mm)
44" (1114mm)
(x) = Depending on the appliance height adjustment: 4" - 5 1/2 "(101.6 mm - 139.7 mm)
Dual Fuel Range dimensions
87
Detailed front side view of HR 1955
Dual Fuel Range dimensions
88
Front side view of HR 1955
2 9/16"
(65.2mm)
3/4"(19mm)
1 5/
16"
1/4"
(x)
(7m
m)
(34m
m)
13 3
/8"
8 1/
8"(2
07m
m)
1 9/
16"
(40m
m)
22 1/4" (564.5mm)
3 5/8"
3 5/8"(92.7mm)
47 15/16" (1218mm)
(1158.4mm)
45 5/8"
1 9/
16"
(40m
m)
27 1/4"
(-1/16" / -2mm)(692mm)
1 3/4"
(45mm)
18 1
1/16
"(4
73.9
mm
)
(92.7mm)
(43m
m)
1 11
/16"
27 1
/2"
(340
.5m
m)
(698
.9m
m)
35 1
/2 -
37"
(901
.7 -
939.
8mm
)
(3mm)
1/8"
(x) = Depending on the appliance height adjustment: 4" - 5 1/2 "(101.6 mm - 139.7 mm)
Dual Fuel Range dimensions
89
Rear view of HR 1955
E = Electrical connection
W = Water connection
G = Gas connection
Dual Fuel Range dimensions
90
Detailed views of HR 1956
Side view of HR 1956
(x)
8 1/
8"
35 1
/2 -
37"
(901
.7 -
939.
8mm
)
37 1
/16"
- 38
9/1
6"
(941
.7 -
979.
8mm
)
24 15/16" (633mm)
27 1/4" (692mm)
28 15/16" (734.4mm)
(207
mm
)
15/16" (24.3mm)
44" (1114mm)
(x) = Depending on the appliance height adjustment: 4" - 5 1/2 "(101.6 mm - 139.7 mm)
Dual Fuel Range dimensions
91
Detailed front side view of HR 1956
Dual Fuel Range dimensions
92
Front side view of HR 1956
2 9/16"
(65.2mm)
3/4"(19mm)
1 5/
16"
1/4"
(x)
(7m
m)
(34m
m)
13 3
/8"
8 1/
8"(2
07m
m)
1 9/
16"
(40m
m)
22 1/4" (564.5mm)
3 5/8"
3 5/8"(92.7mm)
47 15/16" (1218mm)
(1158.4mm)
45 5/8"
1 9/
16"
(40m
m)
27 1/4"
(-1/16" / -2mm)(692mm)
1 3/4"
(45mm)
18 1
1/16
"(4
73.9
mm
)
(92.7mm)
(43m
m)
1 11
/16"
27 1
/2"
(340
.5m
m)
(698
.9m
m)
35 1
/2 -
37"
(901
.7 -
939.
8mm
)
(3mm)
1/8"
(x) = Depending on the appliance height adjustment: 4" - 5 1/2 "(101.6 mm - 139.7 mm)
Dual Fuel Range dimensions
93
Rear view of HR 1956
E = Electrical connection
W = Water connection
G = Gas connection
Anti-tip device
94
Before installation
WARNINGChildren and adults can tip over therange if has not been secured. Thismay lead to fatal injuries.Make sure that the anti-tip device isproperly installed and locked intoplace. It should be screwed to thefloor or wall and engage with thecenter of the bottom of the range.You must take care to protect theinstalled flooring when moving therange.After moving the range, make surethat the anti-tip device locks backinto place. It should be screwed tothe floor or wall and engage with thecenter of the bottom of the range.Do not use the range if the anti-tipdevice has not been properlyinstalled and engaged.Due to the size and weight of theappliance, installation should becarried out by two people.
Any opening in the wall behind theappliance and in the floor under theappliance shall be sealed.
We recommend removing the ovendoor before installing the range (see"Removing the door" in the OperatingInstructions) and all accessories fromthe oven interior. This will make iteasier to install the appliance in itsdesignated space.
Once the range has been installed andsecured against tipping, you canreattach the oven door (see"Reinstalling the door" in theOperating Instructions).
Do not carry or lift the range by theoven door handle or the controlpanel!
Anti-tip device
95
Checking the installation
space
Install the anti-tip device on the floor,concrete wall or timber framing. Thesurface must be flat and level.
Check the base surface.
Check the installation dimensions.
Check the diagrams for the building'ssupply lines. Make sure that you donot damage any lines when drillingthe holes to attach the anti-tipdevice.
Check the position of the electric,gas and water connections (see"Electrical connection", "Gasconnection" and "Plumbing"). Anoverview on the electricalconnections for your range can befound in "Notes on installation".
Included accessories
– 1 anti-tip device
– 4 screws
– 4 plugs
Anti-tip device
96
Installation dimensions of
locking bolt
Anti-tip device, front view
Model Width X
HR 1421
HR 1622
HR 112x
HR 192x
29 15/16"
(760 mm)
3 13/16"
(97 mm)
HR 113x
HR 193x
35 15/16"
(913 mm)
3 13/16"
(97 mm)
HR 195x 47 15/16"
(1218 mm)
3 1/4"
(82 mm)
Installing the range with the
anti-tip device
Wear safety shoes and gloves.
The anti-tip device should be installedat the bottom rear of the range at themidpoint of the width.
Measure the installation space for therange close to floor level.
Mark the wall at the middle of thespace width.
Position the notch of the anti-tipbracket on the wall marking.
The anti-tip device must fit tightly onthe floor or the wall.
Anti-tip device
97
Attaching to the floor
Attaching to the wall
Anti-tip device Screws Locking nut
Secure the anti-tip device to thefloor surface with suitable bearingcapacity, either to the floor or wall.using four screws .
Screw the locking nut to the bolt,see the "Installation dimensions oflocking bolt" table.
Do not push the range into
position before all supply
connections have been
established.
The toe kick cover is attached to thebase of the range by magnets.
Toe kick cover Locking clamp
Remove the toe kick cover fromthe appliance.
Pull out the locking clamp .
The locking clamp extends throughthe toe kick cover of the rangehousing. Its length is approximatelyequal to the depth of the range.
A slot is located in the non-visible rearsection of the locking latch. This slotengages with the bolt of the anti-tipdevice when you slide the lockinglatch into the range.
Anti-tip device
98
Complete all necessary connectionsfor the range. Read the information inthe "Electrical connection", "Gasconnection" and "Plumbing" sections.
The range can be damaged if it islifted using the cover, the trim or thedoor handle.Open the oven door and hold theappliance by the front of the oveninterior.Lift the range and move it with thehelp of the rear wheels.
Slide the range into position, guidingthe middle of the appliance onto theanti-tip device. Slide the appliance allthe way back to the wall.
Use a level to align the range.
– Rear adjustment right and left: You will need an open-end wrench(3/8" (10 mm)).
– Front adjustment right and left: You will need an open-end wrench(5/8" (16 mm)) for the locknut andan open-end wrench (1/2" (13mm)) for the adjustable nut.
Locking clamp Rear adjustment Front adjustment
Align the range.
Slide the locking clamp firmly backinto the range.
Anti-tip device
99
In the range housing, there is anopening for the bolt of the anti-tipdevice. The opening allows the range tobe slid onto the anti-tip device andback to the wall.
The locking clamp must noticeablyengage with the bolt so that anti-tipprotection is ensured for the range.
Opening in the range housing Bolt of the anti-tip device Locking clamp with slot
The toe kick cover can only beattached if the locking clamp hasbeen slid all the way into theappliance.
Install the toe kick cover on therange.
Disconnecting the range from
the anti-tip device
WARNINGChildren and adults can tip over therange if has not been secured. Thismay lead to fatal injuries.
If you need to remove the range fromits installation space, e.g. for service,you first need to disconnect theappliance from the anti-tip device.
Follow the instructions for installationin reverse order.
Electrical connection
100
ATTENTION:During installation, maintenance andrepair work, the range must bedisconnected from the electricalsupply. It is only completely isolatedfrom the electrical supply if the plugfuses have been fully unscrewed(where applicable), the circuitbreaker has been tripped or thepower cord has been unpluggedfrom the wall outlet.
Installation work and repairs shouldonly be performed by a qualifiedtechnician in accordance with allapplicable codes and standards.Repairs and service by unqualifiedpersons could be dangerous and themanufacturer will not be heldresponsible.Installation, repair, andmaintenance work should only beperformed by a Miele-authorizedservice technician. Work byunqualified persons can causeconsiderable danger to users. Mielecannot be held liable for any damagearising as a result of such work.
To avoid damaging the range, makesure that the connection data(voltage and frequency) on the dataplate correspond to the building'spower supply before connecting theappliance.When in doubt, consult a qualifiedelectrician.
The internal electrical wiring of theappliance has been performed andtested according to the validregulations. To guaranteemalfunction-free operation, ensurethe proper phase assignment of thesocket. In case of doubt, ask anelectrician.
The plug must be inserted into asuitable outlet that has beeninstalled and grounded incompliance with all applicable localregulations.
WARNING: THIS APPLIANCE MUST
BE GROUNDED
Installer: Please pass these
instructions on to the customer.
Electrical connection
101
Electrical connection
Type Connecting line NEMA Electrical supply
HR 1421 Approx. 5' 11"(1.80 m)
120/208 V 60 Hz
HR 1421 Approx. 5' 11"(1.80 m)
120/240 V 60 Hz
HR 1622HR 195x
Approx. 5' 11"(1.80 m)
120/208 Vor
120/240 V
60 Hz
HR 192xHR 193x
Approx. 5' 11"(1.80 m)
14-30 Pplug
120/208 Vor
120/240 V
30 A 60 Hz
HR 112xHR 113x
Approx. 5' 11"(1.80 m)
5-15 Pplug
120 V 15 A 60 Hz
Data plate
The data plate with the connection information for the range is located in themiddle of the base front behind the removable toe kick cover (see "Guide to therange").
SAVE THESE INSTRUCTIONS FOR THE ELECTRICAL INSPECTOR'S USE.
40
Electrical connection
102
This appliance must be grounded incompliance with all applicable localand national regulations.Installation, repair and maintenancework should only be performed by aMiele authorized service technicianin compliance with local regulationsand the ANSI National ElectricalCode / NFPA 70 in the United Statesor the Canadian Electrical Code, PartI in Canada (CSA standard C22.1).
Plumbing
103
Notes on connecting to the
water supply
The appliance must be connected tothe water supply by a qualifiedprofessional.Disconnect the appliance from thepower supply before connecting it tothe water line.Turn off the water supply beforeconnecting the water lines for therange.
– All devices used for connecting theappliance to the water supply mustcomply with the current national andlocal safety regulations in the countryin which the range is being installed.
– We do not recommend the use ofwater produced by Reverse Osmosisfiltration systems. Along with thepossibility of detrimental healtheffects, highly purified water cancause the premature corrosion andfailure of components in yourappliance. Furthermore, many ROsystems, especially under countersystems, do not deliver sufficientwater pressure to allow the applianceto operate properly. Connection tosuch a water supply could causepoor performance, prematureappliance failure, leaks and/orflooding. Miele will not beresponsible for any damages causedby appliances connected to thesesystems. Only use filtered, softenedand demineralized water from thebuilding's plumbing to supply theoven.
– Connect the range to a cold water
supply only.
– The range may be connected to awater supply without a non-returnvalve.
– A water shut-off valve must beprovided between the stainless steelhose and the household water supplyto ensure that the water supply canbe cut off if necessary.
– The water shut-off valve must beaccessible after installation.
– The water pressure must be between1 and 10 bar (105 and 106 Pa or 14.5and 145 psi). If the pressure is higherthan this, install a pressure reducer.
– 30" and 36" range: The providedstainless steel hose has a length of 4'11" (1.5 m).48" Range: The provided stainlesssteel hose has a length of 9' 10"(3 m). Longer intake hoses are available ifnecessary. Do not shorten the hoses.
– The total hose length must notexceed 24.5 ft. (7.5 m).
Ensure that the shut-off valve isaccessible after installation.
Replace the stainless steel hose if itis damaged, using only an originalMiele hose to do so (available fromMiele). The hose must be suitable forsupplying drinking water.
Plumbing
104
Attach the stainless steel hose
to the range.
Make sure that the stainless steelhose is not kinked or damaged. Thestainless steel hose must not beshortened.
Remove the cover from the watersupply connection at the back of therange.
Take the angled side of the stainlesssteel hose and check whether agasket is present. If not, insert one.
Screw the stainless steel hosecoupling nut onto the threaded union.
Ensure that the hose is correctlyseated.
Connecting to the water
supply
Danger of electric shock!Disconnect the range from theelectrical supply before connecting itto the water supply.
Check that the gasket is present.Replace, if not, insert beforeconnecting to the water supply.
3/8"
Connect the stainless steel hose tothe water supply.
Old or previously used tubing shouldnever be connected to the range.Only use the stainless steel hosesupplied.
Ensure that the hose is correctlyseated.
Slowly open the shut-off valve to thewater supply and check for leaks.
Gas connection
105
Connection to the gas supplymay only be performed by a dulyauthorized technician. Thistechnician is responsible for properfunction at the installation site.In Massachusetts, the gasconnection may be performed onlyby a certified gas installer.
The range must be connected withits own shut-off valve.The shut-off valve must beaccessible and visible, after theopening of a cabinet door, ifnecessary.
The connection of the range can befor natural gas or liquid gas(propane) according to the model.Ask your gas company what kind ofgas is used and compare it with thespecifications on the data plate.
The range is not connected to anexhaust vent.During the setup and connection ofthe range, observe the applicableinstallation conditions, especiallysuitable ventilation measures.
The gas connections must bearranged in such a way that they arenot heated and damaged by theoperation of the range.In particular, make sure that the gashose lines and connection fittings onthe range do not come into contactwith hot exhaust gases.
Flexible connection lines can bedamaged by incorrect routing.Attach flexible connecting lines insuch a way so that they do not comeinto contact with any moving kitchenparts (e.g., a drawer) and are notexposed to mechanical stress.
The range and the shut-off valvemust be disconnected from the gassupply during gas pressure tests.Disconnect the range and the shut-off valve from the gas supply beforeperforming a gas pressure test at apressure of more than 1/2 psi(3.5 kPA). Close the shut-off valve ofthe gas supply before performing agas pressure test at a pressure ofless than or equal to 1/2 psi(3.5 kPA).
Incorrectly sealed gas lines can leadto a gas leak and thus to anexplosion.Seal all gas lines with a suitablethread sealant.
Seal tightness tests on the rangemust be performed according tomanufacturer specifications.
The gas connection must beestablished only Miele-authorizedspecialists according to the local andfollowing regulations:National Fuel Gas CodeANSI Z 21.1 / NFPA No. 54 for theUnited States or the current Can /CGA B 149.1 and 2 InstallationCodes of Gas Appliances forCanada.
Gas connection
106
The installation must conform withlocal codes or, in the absence oflocal codes, with the National FuelGas Code, ANSI Z223.1/NFPA 54.
The gas pressure may notundershoot or exceed certain values.Make sure that the maximum gaspressure upstream of the gaspressure controller does not amountto more than 1/2 psi (3.5 kPA) fornatural and liquid gas.Make sure that the minimum gaspressure amounts to a 6" (150 mm)water head in the case of natural gasand a 11" (279,4 mm) water head inthe case of liquid gas.
G NPT1/2"
Burner ratings of Standard Burner Configuration
107
Burner ratings for HR 1124
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Oven top burner Natural gas 22.000 6.45
Propane gas 20.150 5.90
Oven bottomburner
Natural gas 23.200 6.79
Propane gas 23.200 6.79
Total output ofCooktop
Natural gas 71.000 20.80
Propane gas 71.000 20.80
Maximum totaloutput of Range
Natural gas 94.200 27.59
Propane gas 94.200 27.59
Burner ratings of Standard Burner Configuration
108
Burner ratings for HR 1134
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Oven top burner Natural gas 22.000 6.45
Propane gas 20.150 5.90
Oven bottomburner
Natural gas 25.500 7.47
Propane gas 27.000 7.90
Total output ofCooktop
Natural gas 110.000 32.20
Propane gas 110.000 32.20
Maximum totaloutput of Range
Natural gas 135.500 39.67
Propane gas 137.000 40.10
Burner ratings of Standard Burner Configuration
109
Burner ratings for HR 1135
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Grill Natural gas 19.000 5.50
Propane gas 15.500 4.50
Oven top burner Natural gas 22.000 6.45
Propane gas 20.150 5.90
Oven bottomburner
Natural gas 25.500 7.47
Propane gas 27.000 7.90
Total output ofCooktop
Natural gas 90.000 26.30
Propane gas 86.500 25.30
Maximum totaloutput of Range
Natural gas 115.500 33.77
Propane gas 113.500 33.20
Burner ratings of Standard Burner Configuration
110
Burner ratings for HR 1136
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Griddle Natural gas 13.000 3.80
Propane gas 14.300 4.20
Oven top burner Natural gas 22.000 6.45
Propane gas 20.150 5.90
Oven bottomburner
Natural gas 25.500 7.47
Propane gas 27.000 7.90
Total output ofCooktop
Natural gas 84.000 24.60
Propane gas 85.300 25.00
Maximum totaloutput of Range
Natural gas 109.500 32.07
Propane gas 112.300 32.90
Burner ratings for HR 1924
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Total output ofCooktop
Natural gas 71.000 20.80
Propane gas 71.000 20.80
Burner ratings of Standard Burner Configuration
111
Burner ratings for HR 1934
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Total output ofCooktop
Natural gas 110.000 32.20
Propane gas 110.000 32.20
Burner ratings for HR 1935
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Grill Natural gas 19.000 5.50
Propane gas 15.500 4.50
Total output ofCooktop
Natural gas 90.000 26.30
Propane gas 86.500 25.30
Burner ratings of Standard Burner Configuration
112
Burner ratings for HR 1936
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Griddle Natural gas 13.000 3.80
Propane gas 14.300 4.20
Total output ofCooktop
Natural gas 84.000 24.60
Propane gas 85.300 25.00
Burner ratings for HR 1954
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Total output ofCooktop
Natural gas 142.000 41.60
Propane gas 142.000 41.60
Burner ratings of Standard Burner Configuration
113
Burner ratings for HR 1955
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Grill Natural gas 19.000 5.50
Propane gas 15.500 4.50
Total output ofCooktop
Natural gas 122.000 35.70
Propane gas 118.500 34.70
Burner ratings for HR 1956
Gas type BTU/hr kW
max max
Simmer burner Natural gas 12.500 3.70
Propane gas 12.500 3.70
Power burner Natural gas 19.500 5.70
Propane gas 19.500 5.70
Griddle Natural gas 13.000 3.80
Propane gas 14.300 4.20
Total output ofCooktop
Natural gas 116.000 34.00
Propane gas 117.300 34.40
Caring for the environment
115
Disposal of the packing
material
The cardboard box and packingmaterials protect the appliance duringshipping. They have been designed tobe biodegradable and recyclable.
Ensure that any plastic wrappings,bags, etc. are disposed of safely andkept out of the reach of children.Danger of suffocation!
Disposal of your old appliance
Old electrical and electronic appliancesoften still contain valuable materials.However, they also contain harmfulsubstances that were essential for theproper functioning and safe use of theequipment. Handling these materialsimproperly or disposing of them in yourhousehold waste can be harmful toyour health and the environment.Therefore, please do not dispose ofyour old appliance with regularhousehold waste.
Old appliances may contain materialsthat can be recycled. Please contactyour local recycling authority about thepossibility of recycling these materials.
Please be sure that your old appliancedoes not pose a danger to childrenwhile being stored for disposal.
9 Independence Way
Princeton, NJ 08540
Phone:
Fax:
www.mieleusa.com
U.S.A.
Miele, Inc.
National Headquarters
Please have the model and serial number
of your appliance available before
contacting Technical Service.
Canada
Importer
Miele Limited
Headquarters and Miele Centre
800-843-7231
609-419-4298
Technical Service & Support
Nationwide
Phone:
Fax:
161 Four Valley Drive
Vaughan, ON L4K 4V8
www.miele.ca
800-999-1360
888-586-8056
Customer Care Centre
Phone:
800-565-6435
905-532-2272
Germany
Manufacturer
Miele & Cie. KG
Carl-Miele-Straße 29
33332 Gütersloh
116
M.-Nr. 09 898 161 / 03en - US, CA
All Electric: HR1421; HR1622; All Gas: HR1124; HR1134; HR1135;HR1136; Dual Fuel: HR1924; HR1934; HR1935; HR1936; HR1954;HR1955; HR1956