Installation Accessories and Applications - Pella...
Transcript of Installation Accessories and Applications - Pella...
W-IA-1Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Installation Accessories and ApplicationsIntroduction ..................................................................................................................................................W-IA-2
Window Attachment Options............................................................................................................W-IA-4
Subsill ...................................................................................................................................................W-IA-6
Exterior Mullions .................................................................................................................................W-IA-8
Mullion Cover Application ...............................................................................................................W-IA-10
Mullion Reinforcements ...................................................................................................................W-IA-12
Reinforcing Mullion Application .....................................................................................................W-IA-13
Expansion Mullion Cover Application ............................................................................................W-IA-14
Mullion Considerations ....................................................................................................................W-IA-16
Commercial Structural Receptor Mullions .....................................................................................W-IA-17
Exterior Trim Applications ................................................................................................................W-IA-22
Frame Expansion Application .........................................................................................................W-IA-25
EnduraClad® Exterior Trim ..............................................................................................................W-IA-29
EnduraClad® Exterior Trim Applications .......................................................................................W-IA-31
Commercial Replacement Accessories..........................................................................................W-IA-35
Break Metal ........................................................................................................................................W-IA-37
Wood Exterior Mullion Covers ........................................................................................................W-IA-40
Window and Door Subsills and Exterior Trim ...............................................................................W-IA-41
Interior Casings .................................................................................................................................W-IA-42
Interior Stools and Trim ....................................................................................................................W-IA-43
ReadyTrim ..........................................................................................................................................W-IA-44
Interior Jamb Extensions .................................................................................................................W-IA-45
Interior Mullion Covers ....................................................................................................................W-IA-45
AZEK Trim Details
Custom Window Shapes..................................................................................................................W-IA-46
Exterior Surround Trim .....................................................................................................................W-IA-47
Custom Door Shapes .......................................................................................................................W-IA-48
2" Brickmould with Sill .....................................................................................................................W-IA-49
Exterior Surround Trim .....................................................................................................................W-IA-50
Flat Casing with Sill Nose and Crown ............................................................................................W-IA-51
Pocket Replacment
Exterior Pocket Installation ..............................................................................................................W-IA-54
Interior Pocket Installation ...............................................................................................................W-IA-55
SECTION DIRECTORY
W-IA-2Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
This section presents available installation accessories which, when used in conjunction with proper Pella installation procedures, will provide
for a robust installation for single or combination units. Window and door attachment accessories used for both clad and primed wood
exterior units are illustrated in this section.
Aside from attachment accessories, this section reviews accessories to meet the following requirements:
• Combination applications, such as mullion covers, expansion mullion covers, reinforcement mullions and bay and bow accessories.
• Interior casings and stools
• Subsills
• Traditional and flat trim
INTRODUCTION
W-IA-3Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION ACCESSORIES
Accessory Indiv. Part No.
Box No.
Installation Fin 42G7 0BLA
Head Drip Cap 72GW 0BLB
Curved Head Drip Fin 72Y5 —
Elliptical Head Drip Fin 72Y7 —
Quarter Circle Head Drip Fin 72Y6 —
Head Drip Flashing 72WA 0BMS
Head Flashing 72W8 —
Receptor 72AK 06Y1
Receptor Gasket — 0DA9
6" Installation Clip 5071 0635
8" Installation Clip 5071 0B51
T-Subframe Clip 5027 0DB03"-wide Smart Flash® Installation Tape (150' rolls)
850H0000 0CFV
6"-wide Smart Flash® Installation Tape (50' rolls)
850H0004 01FM
SUBSILLS
Accessory Indiv. Part No.
BoxNo.
Clad / Wood Subsill 4049 0B13
Subsill Clip 7366 0B14
Replacement Sill Adaptor 70DK —
WOOD SILL PLATES FOR CLAD WINDOWS
Accessory Indiv. Part No.
BoxNo.
CM / AW Sill Plate 2722 0C79
ProLine® Sill Plate 2772 —
ATTACHMENT OPTIONS
72GW 72WA 72W8 72Y5
W-IA-4Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 6" = 1' 0" Scale 3" = 1' 0"
ATTACHMENT OPTIONS
Installation Fin
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
H
J
S
To determine window openings for typical installations, add 3/4" to frame width and 3/4" to frame height.
• For large size units, out of plumb opening, and/or in masonry construction, the need for additional jamb clearances should be reviewed.
• Typical installation details and accessories are shown in the Installation Details and Installation Accessories sections.
• Determine if unit performance meets design requirements. Unit performance class and grade are in each product section.
Not to scale.
W-IA-5Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
[64]
2 1/
2"
RO
UG
H O
PE
NIN
G
FRA
ME
[10]
3/8"
[10]3/8"
ROUGH OPENING
FRAME
FRA
ME
RO
UG
H O
PE
NIN
G
[10]
3/8"
HEAD
JAMB
SILL
To determine window openings for typical installations, add 3/4" to frame width and 3/4" to frame height.
• For large size units, out of plumb opening, and/or in masonry construction, the need for additional jamb clearances should be reviewed.
• Typical installation details and accessories are shown in the Installation Details and Installation Accessories sections.
• Determine if unit performance meets design requirements. Unit performance class and grade are in each product section.
H
J
S
INSTALLATION SYSTEMSNew Construction — Punched OpeningClip Installation
W-IA-6Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 3" = 1' 0"
Detail at right: Custom 0.05" (1.27) aluminum sill flashing used with clad wood subsill.
Subsills are recommended for installations where recaulking would be difficult or high weather exposure exists due to the height or location of the building. The need for the subsill weep system is increased where there are multiple units in a given opening.
Used with Pella clad windows.
• A continuous perimeter line of sealant is required on the interior with clad / wood subsill #4049. • Where the aluminum comes into contact with the cement materials, apply protective coating to separate galvanically incompatible materials.• The clad / wood subsill is a primed, preservative treated wood for use with Pella aluminum clad / wood windows. • The aluminum frame expander covers the front edge of the subsill.
Note: The clad wood subsill is an open weep system. An interior air seal is critical to the performance of this system. Also, DO NOT SEAL the exterior frame expander to the opening.
ATTACHMENT OPTION APPLICATIONS
Clad Wood Subsill
W-IA-7Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 6" = 1' 0" Scale 3" = 1' 0"
ATTACHMENT OPTION APPLICATIONS
L Receptor Application
W-IA-8Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Mullion Covers Indiv. Part No.
Box No.
12° 45' 72A3 0B43
30° 72A4 0B37
45° 72A5 0C72
Jamb Covers Indiv. Part No.
12° 45'/30º 47L2
45° 47K4
BAY AND BOW MULLION ACCESSORIES
Bay Wedges Indiv. Part No.
BoxNo.
12° 45' 33CX 0B19
30° 33CW 0B20
45° 34A3 0B21
See the Architectural Design Manual Bay/Bow section for cross sections of application.
EXTERIOR MULLIONS
Bay/Bow Mullion Accessories
W-IA-9Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
EXTERIOR MULLIONS
Mullion Covers
MULLION COVERS
Mullion Cover A (Frame to Frame)
B (Overall Part Dimension)
Part Number Thickness (In.)
Standard (Direct) 0" 3/8 7217 0.047
1/2" 1/2" 7/8 736M 0.047
1" 1" 1-3/8 736N 0.047
1-1/2" 1-1/2" 1-7/8 736P 0.047
2" 2" 2-3/8 72A9 0.047
2-1/2" 2-1/2" 2-7/8 736T 0.047
3" 3" 3-3/8 736U 0.060
3-1/2" 3-1/2" 3-7/8 736V 0.060
4" 4" 4-3/8 736W 0.060
Custom (Break Metal)
Min 5/8" Max 12"
B = A + 3/8" 100 Mullion Cover 0.050
[16 - 305]SPCL. 5/8" - 12"
[8]
5/16
"
100 Mullion CoverBreak Metal
736W4" Mullion Cover
736V3-1/2" Mullion Cover
736U3" Mullion Cover
736T2-1/2" Mullion Cover
72A92" Mullion Cover
736P1-1/2" Mullion Cover
736N1" Mullion Cover
736M1/2" Mullion Cover
7217STANDARD
B
Mullion CoversStandard EnduraClad
[16 - 305]A = SPCL. 5/8" - 12"
100 Mullion CoverBreak Metal
B
A
B
3" Structure3 1/2" Mullion Cover
ARO
FRAME FRAMERO
Structure
[111]4 3/8"
[102]4"
[98]3 7/8"
[89]3 1/2"
[85]3 3/8"
[76]3"
[73]2 7/8"
[64]2 1/2"
[60]2 3/8"
[51]2"
[47]1 7/8"
[38]1 1/2"
[35]1 3/8"
[25]1"
[22]7/8"
[13]1/2"
[9]3/8"
For all but direct mullion, dimension A is to inside of bends. Frame to Frame plus 1/4" equals dimension to inside of bends.A = B - 3/8"
Standard mull covers are extruded aluminum.
W-IA-10Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
CUSTOM BREAK METAL MULLION COVER
90° MULLION COVER #4994
Mullion covers are not intended to create a completely waterproof seal.
See typical sealant details.
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
INSTALLATION CLIPS #5071 @ 18" (457) O. C. (REFER TO PAGE (17) FOR ADDITIONAL SPACING INFORMATION
CONTINUOUS INSTALLATION FINS #42G7
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
NOTE: APPLY CONTINUOUS BEAD OF SEALANT TO INSIDE CORNERS OF MULLION COVER BEFORE INSTALLING UNITS.
100 Mullion cover is fabricated from 0.050" Aluminum for widths of 5/8" to 12" (16 - 305).
(Dimension A is to inside of bends. Frame to Frame plus 1/4" equals dimension to inside of bends.)
Use of installation fins #42G7 recommended with 90° mullion.
Scale 6" = 1' 0" Scale 3" = 1' 0"
MULLION APPLICATIONS
W-IA-11Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Mullion covers are not intended to create a completely waterproof seal.
See typical sealant details.
Scale 6" = 1' 0" Scale 3" = 1' 0"
NOTE: Apply continuous bead of sealant to inside corners of mullion cover before installing to units.
CONTINUOUS SEALANT BY OTHERS
MULLION REINFORCEMENT #2941
1" x 1/2" CROWN STAPLE B.O.
CORRUGATED FASTENERS
@ 12" (305) O. C. BY OTHERS
INTERIOR WOOD MULLION COVER #2941
TYPICALLY USED WITH 1/2" (10) MULLION REINFORCEMENT #0A6G
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
INSTALLATION CLIPS #5071 @ 18" (457) O.C. (REFER TO PAGE 17 FOR ADDITIONAL SPACING INFORMATION)
2" (51) MULLION COVER #72A9
STANDARD SIZE MULLION COVERS AVAILABLE IN 1/2" INCREMENTS FROM 1" to 4" AS NEEDED.
USED TO JOIN TWO CLAD UNITS WHERE NO MULLION REINFORCEMENT IS REQUIRED
NOTE: Apply continuous bead of sealant to inside corners of mullion cover before installing to units.
MULLION APPLICATIONS
W-IA-12Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
MULLION REINFORCEMENTS
MULLION REINFORCEMENTS
Accessory Indiv. Part No.
BoxNo.
Mullion Reinforcement 1/2" x 3-9/16" 0A6G 0EUAMullion Reinforcement 1/2" x 4-9/16" 0A6K 0EULClip Mullion Anchor 512C 00NN0003High Performance Mullion Anchor 000F 0CSL0025Wood Mullion Anchor 512A 00NN0001Mullion End Splice - 96" 72WQ 0CUHSubsill Mullion Anchor 512B 00NN0002Fin Mullion Anchor 512D 00NN000420" Plate 500P 0DKM0000
Scale 3" = 1' 0"
W-IA-13Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
1. Attach 1/2" mullion reinforcements with clips #512C, 000F, 512B or 512D.
2. Can be used either horizontally or vertically for wind load mullion reinforcement. Note: Recommended use is vertically with subsill for large combination assemblies.
3. Do not use as part of building structure.4. Refer to Combinations Section for wind load information,
(max. Length 144").
WOOD TRIM BY OTHERS
1" x 1/2" Crown Staple B.O.
1" x 1/2" CROWN STAPLE B.O.
WOOD TRIM BY OTHER
NOTE: Apply continuous bead of sealant to inside corners of mullion cover before installing to units.
NOTE: Apply continuous bead of sealant to inside corners of mullion cover before installing to units.
CONTINUOUS SEALANT BY OTHER
CONTINUOUS SEALANT BY OTHER
Scale 6" = 1' 0" Scale 3" = 1' 0"
REINFORCING MULLION APPLICATIONS
FACTORY ASSEMBLED WOOD MULLION END ANCHORS
Wood Mullion Anchor
Refer to the Combination Recomendations section and Combination size tables to determine required reinforcement method.
Wood Reinforcing mullion 1" to 4" on 1/2" increments.
End Anchors Attachment:• For Wood Framing: Use 5 -
#10 x 3" Wood Screws.• For Concrete/CMU: Use
5-3/16" Masonry Screw.
1/2" FIN MULLION END ANCHORS
Rough Framing: Wood, Concrete, CMU, etc.
Fin Anchor #512D
1/2" x 3-9/16" Reinforcing mullion #0A6G
Fin Anchor #512D
End Anchors Attachment:
• For Wood: Use 5 - #10 x 3" Wood Screws.
• For Concrete/CMU: Use 3/16" Masonry Screw.
Rough Framing: Wood, Concrete, CMU, etc.
The 1/2" mullion assembly with end anchors 512D (fin mullion anchor), 000F (high performance fin mullion anchor) or 512A (wood fin mullion anchor) allow for installation of combinations that are assembled prior to being placed in the opening. Combinations assembled with this method should not exceed 144 square feet in total size. Always handle combinations in vertical orientation.
Example Assembly
Screws have a 1" embedment into wood buck or concrete below subsill.
W-IA-14Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 6" = 1' 0" Scale 3" = 1' 0"
EXPANSION MULLION COVER APPLICATIONS
T-Expansion Mullion Application
Expansion Mullion Cover
W-IA-15Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
[10]3/8"
[10]3/8"
[10]3/8"
[10]3/8"
[10]3/8"
[13]1/2"
VARIES FRAME
Clip InstallationFin Installation
Clip InstallationFin Installation
FRAME
VARIES FRAMEFRAME
[10]3/8"
[42]1 5/8"
Varies
[13]1/2"
FRAMEFRAME
[51]2"
[25]1"
[9]
3/8"
VARIES FRAMEFRAME
72HFEXPANSION MULLION COVER
1AAFVINYL BULB GASKET
EXPANSION MULLION COVER WITH
[32]1 1/4"
Scale 3" = 1' 0"
INSTALLATION CLIPS #5071 @ 18" (457) O. C.
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
INSTALLATION CLIPS #5071 @ 18" (457) O. C.
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
NOTE: APPLY CONTINUOUS BEAD OF SEALANT TO INSIDE CORNERS OF MULLION COVER BEFORE INSTALLING UNITS.
EXPANSION MULLION COVER APPLICATIONS
Rev. 02/24/2016
W-IA-16Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSNew Construction — Punched OpeningMulling Considerations
Refer to single-unit opening recommendations in addition to the following:
1 1/2" clearance is recommended at each jamb in masonry construction and/or when window opening height or width is 10' or greater.
2 All four-way mullion intersections require reinforcing mullion in one direction (either vertically or horizontally). See mullion load chart pages in the Installation section on PellaADM.com.
3 Check combination (joining) mullion limitation for specified wind loading. Combination (joining) and reinforcing mullions are shown on the mullion load chart pages in the Installation section on PellaADM.com.
4 Subsill systems that weep incidental moisture to the exterior are recommended for water management in openings where the potential for water infiltration is increased and may not be adequately managed by the building weather barrier, flashings and drainage system. Sample conditions include, but are not limited to: increased level of exposure due to multi-story construction, high weather exposure, recaulking would be difficult or unlikely, non-standard installation methods, or when there are multiple units joined within the opening.
If lower unit is venting, horizontal reinforcing mullion may be required to carry weight of upper units. See Weight Limitations Over Windows information in the Installation and Performance section on PellaADM.com.
MULLION REINFORCEMENT 1/2" X 3-9/16"
STANDARD MULLION COVER
EXPANSION MULLION COVER
MULLION COVER (RANGE: FRAME TO FRAME 1" TO 4")
Burlington Apartments, Portland, OR
Ankrom Moisan Associated Architects
These recommendations apply to a typical grouping of any combination of window units that form a four-way mullion intersection.
W-IA-17Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSNew Construction — Punched OpeningL-Receptor and 2" Vertical Structural Receptor
& CLIP 7366 CLAD / WOOD SUBSILL 4049
2" Structural Receptor Mullion 0APK
Bulb Gasket 0SA9L-Receptor Clip 5027L-Receptor 72AK
VERTICAL MULLION
SILL
JAMB
HEAD
W-IA-18Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSNew Construction — Store Fronts
Refer to single-unit opening recommendations in addition to the following:
• 1/2" clearance is recommended at each jamb in masonry construction and/or when window opening height or width is 10' or greater.• All four-way mullion intersections require reinforcing mullion in one direction (either vertically or horizontally). See mullion load chart
pages in the Installation section on PellaADM.com.• Check combination (joining) mullion limitation for specified wind loading. Combination (joining) and reinforcing mullions are shown
on the mullion load chart pages in the Installation section on PellaADM.com.• Subsill systems that weep incidental moisture to the exterior are recommended for water management in openings where the potential
for water infiltration is increased and may not be adequately managed by the building weather barrier, flashings and drainage system. Sample conditions include, but are not limited to: increased level of exposure due to multi-story construction, high weather exposure, recaulking would be difficult or unlikely, non-standard installation methods, or when there are multiple units joined within the opening.
If lower unit is venting, horizontal reinforcing mullion may be required to carry weight of upper units. See Weight Limitations Over Windows information in the Installation and Performance section on PellaADM.com.
Burlington Apartments, Portland, OR
Ankrom Moisan Associated Architects
Standard Frame Expander
Expansion Cover with Gasket 1AAFHorizontal Mullion
1 1/2" Mullion Cover 736B[5
1]2" Window Wall Channel 2" Structure 50E4 Vertical Mullion
2" Structure 50E5Vertical Receptor Mullion
1 3/4" Structure 50E3Horizontal Receptor Mullion
[51]2"
[44]
1 3/
4"
1
2
3
4 5
6Elevation
W-IA-19Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSNew Construction — Store Fronts
HORIZONTAL MULLION
SILL
HEAD
1
2
3
VERTICAL MULLION
SILL
JAMB
4
5
6
Scale 3" = 1' 0"
W-IA-20Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSNew Construction — Window Walls
Environmental Nature Center, Newport Beach, CA; LPA Inc. LEED® Platinum
Photo © Costea Photography, Inc.
1
2
3
4 5 6
ELEVATION
Refer to single-unit opening recommendations in addition to the following:
• 1/2" clearance is recommended at each jamb in masonry construction and/or when window opening height or width is 10' or greater.
• All four-way mullion intersections require reinforcing mullion in one direction (either vertically or horizontally). See mullion load chart pages in the Installation section on PellaADM.com.
• Check combination (joining) mullion limitation for specified wind loading. Combination (joining) and reinforcing mullions are shown on the mullion load chart pages in the Installation section on PellaADM.com.
• Subsill systems that weep incidental moisture to the exterior are recommended for water management in openings where the potential for water infiltration is increased and may not be adequately managed by the building weather barrier, flashings and drainage system. Sample conditions include, but are not limited to: increased level of exposure due to multi-story construction, high weather exposure, recaulking would be difficult or unlikely, non-standard installation methods, or when there are multiple units joined within the opening.
If lower unit is venting, horizontal reinforcing mullion may be required to carry weight of upper units. See Weight Limitations Over Windows information in the Installation and Performance section on PellaADM.com.
Standard Frame Expander
Expansion Cover with Gasket 1AAFHorizontal Mullion
1 1/2" Mullion Cover 736B
[51]2" Window Wall Channel 2" Structure 50E4
Vertical Mullion
2" Structure 50E5Vertical Receptor Mullion
1 3/4" Structure 50E3Horizontal Receptor Mullion
[51]2"
[44]
1 3/
4"
W-IA-21Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSNew Construction — Window Walls
HORIZONTAL MULLION
SILL
HEAD
JAMB
VERTICAL MULLION
VERTICAL MULLION - STEEL OPTION
1
2
3
4
5
6
Scale 3" = 1' 0"
W-IA-22Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Aluminum traditional flat trim is to be used in frame construction with standard installation fins only.
Maximum length is 8'.
Scale 6" = 1' 0" Scale 3" = 1' 0"
EXTERIOR TRIM - FIELD APPLIED APPLICATION
Traditional Trim and Clad Sill Nose
Siding Applications
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
W-IA-23Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Aluminum traditional flat trim is to be used in frame construction with standard installation fins only.
Maximum length is 8'.
EXTERIOR TRIM - FIELD APPLIED APPLICATION
Traditional Trim and Clad Sill Nose
Brick Veneer Applications
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
FIELD APPLIED EXTERIOR TRIM
Accessory Indiv. Part No.
BoxNo.
Traditional Trim 72D6 0DC33-1/2" Flat Trim Head 72D4 0DC4
3-1/2" Flat Trim Jamb 72D5 72E0 0DC5
1/2" Clad Sill Nose 72D8 0DC6
W-IA-24Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 6" = 1' 0" Scale 3" = 1' 0"
Aluminum traditional flat trim is to be used in frame construction with standard installation fins only.
Maximum length is 8'.
EXTERIOR TRIM - FIELD APPLIED APPLICATION
Flat Trim with Clad Sill Nose
Siding Applications
W-IA-25Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
EXTERIOR TRIM - FRAME EXPANDERFrame ExpanderFrame Expander Receptor
Application: New Construction or Renovation
• For use with aluminum-clad wood windows• Provides the look of flat trim• Receptor available for wide trims• Paint finish that matches windows• Available with or without brickmould• Custom brickmould profiles available• Straight or curved• Trim to frame opening• Factory Supplied Frame Expander Kits available,
trim is processed and notched to length per unit configuration, saves time and scrap on the job site.
FRA
ME
(do not use high pressure or latex foam.)Insulating Window and Door Sealant.Low Expansion, Low Pressure Polyurethane
Water Resistant Backer Rod and Sealant. by OthersPELLA Window and Door Installation Sealant. and
@ 18" (457) O.C. INSTALLATION CLIPS
FRAME EXPANDER RECEPTOR1" FRAME EXPANDER
(do not use high pressure or latex foam.)Insulating Window and Door Sealant.Low Expansion, Low Pressure Polyurethane
Continuous Bead of Sealant by Others.Continuous Wood Blocking, Wood Trim
Water Resistant Backer Rod and Sealant. by OthersPELLA Window and Door Installation Sealant. and
Shim Units Plumb and Level as Required
[32]
1 1/
4"
[27]1 1/16"
[8]5/16"
FRAME EXPANDER RECEPTOR
[13]
1/2"
JAMB
MA
SO
NR
Y O
PE
NIN
G
[19]
3/4"
RO
UG
H O
PE
NIN
G
[10]
3/8"
6" Frame Expander
4" Frame Expander
2 1/2" Frame Expander
1 3/4" Frame Expander
1" Frame Expander
[30]
1 3/
16"
[49]
1 15
/16"
[68]
2 11
/16"
[108
]4
1/4"
[152
]6"
MA
SO
NR
Y O
PE
NIN
G
RO
UG
H O
PE
NIN
G
[10]
3/8"
FRA
ME
@ 18" (457) O.C. INSTALLATION CLIPS
FRAME EXPANDER RECEPTOR1" FRAME EXPANDER
Continuous Bead of Sealant by Others.Continuous Wood Blocking, Wood Trim
required.into blocking. Return leg can be field-trimmed asexpander as an alternate to face-screwing edgeUsed to receive and trim outside edge of frame
HEADUsed at head, jamb and/or sill.
Scale 6" = 1' 0" Scale 3" = 1' 0"
W-IA-26Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
47D36"
47E34"
47D62 1/2"
47D51 3/4"
47D41"
[30]
1 3/
16"
[49]
1 15
/16"
[68]
2 11
/16"[1
08]
4 1/
4"
[152
]6"
FRA
ME
[10]
3/8"
[10]
3/8"
[95]
3 3/
4"R
OU
GH
OP
EN
ING
MA
SO
NR
Y O
PE
NIN
G
FRA
ME
[10]
3/8"
[10]
3/8"
[95]
3 3/
4"R
OU
GH
OP
EN
ING
MA
SO
NR
Y O
PE
NIN
GM
AS
ON
RY
OP
EN
ING
RO
UG
H O
PE
NIN
G
[10]
3/8"
FRA
ME
Frame Expander
Custom Brickmould with Clip
[30]
1 3/
16"
[22]
7/8"
[37]
1 1/
2"[3
7]1
1/2"[27]
1 1/
16"
[27]
1 1/
16"
[43]
1 11
/16"
[48]
1 7/
8"
[33]
1 5/
16"
[48]
1 7/
8"
[52]
2 1/
16"
[57]2 1/4"
[36]1 7/16"
[23]15/16"
[16]5/8"
[41]1 5/8"
[38]
1 1/
2"
[38]1 1/2"
72AN - 72AQ2 1/16"
72AP - 72AQ1 7/8"
7SB1 - 0SBQ1 5/16"
7SBP - 0SBN1 7/8"
7SBX - 0SBN1 11/16"
7SB7 - 0SB81 1/2"
SILL
JAMB
HEAD
EXTERIOR TRIM - NEW CONSTRUCTION APPLICATION
Aluminum Brickmould
Aluminum Brickmould Clip
Scale 3" = 1' 0"
W-IA-27Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
MA
SO
NR
Y O
PE
NIN
G
[14]
1 1/
2"R
OU
GH
OP
EN
ING
[10]
3/8"
FRA
ME
[10]
3/8"
[38]
1 1/
2"
FRA
ME
[10]
3/8"
RO
UG
H O
PE
NIN
G
MA
SO
NR
Y O
PE
NIN
G
FRA
ME
[10]
3/8"
[10]
3/8"
[38]
1 1/
2"R
OU
GH
OP
EN
ING
MA
SO
NR
Y O
PE
NIN
G
Frame Expander
47D36"
47E34"
47D62 1/2"
47D51 3/4"
47D41"
[30]
1 3/
16"
[49]
1 15
/16"
[68]
2 11
/16"[1
08]
4 1/
4"
[152
]6"
Custom Brickmould with Clip
[30]
1 3/
16"
[22]
7/8"
[37]
1 1/
2"[3
7]1
1/2"[27]
1 1/
16"
[27]
1 1/
16"
[43]
1 11
/16"
[48]
1 7/
8"
[33]
1 5/
16"
[48]
1 7/
8"
[52]
2 1/
16"
[57]2 1/4"
[36]1 7/16"
[23]15/16"
[16]5/8"
[41]1 5/8"
[38]
1 1/
2"
[38]1 1/2"
72AN - 72AQ2 1/16"
72AP - 72AQ1 7/8"
7SB1 - 0SBQ1 5/16"
7SBP - 0SBN1 7/8"
7SBX - 0SBN1 11/16"
7SB7 - 0SB81 1/2"
ConstructionExisting Wall
ConstructionExisting Wall
Units as RequiredShim, Level & Plumb
SILL
HEAD
JAMB
ConstructionExisting Wall
Sealant by Others.Wood Blocking, Trim and
EXTERIOR TRIM - RENOVATION APPLICATION
Aluminum Brickmould
Aluminum Brickmould Clip
Scale 3" = 1' 0"
W-IA-28Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
BRICKMOULD CLIP #72AQ.PELLA STANDARD
BRAKE METAL
WITH WEEPS.OF SEALANT
CORNER BEAD
AS REQ'D.WITH NEW BLOCKINGFILL WALL CAVITY
AS REQ'D.WITH NEW BLOCKINGFILL WALL CAVITY
AS REQ'D.WITH NEW BLOCKINGFILL WALL CAVITY
BRICKMOULD CLIP #72AQ.PELLA STANDARD
EXISTING CONSTRUCTION
conditions.as needed to actual project119 Break Metal Configured
Sill Cover # 49A1M119
[57]
2 1/
4"
[41]1 5/8"
Trim # 19876
Architect Series Monumental HungAll other Clad Wood products including
Trim # 19875
Clip # 72AQ Brickmould # 19874
with Clip Brickmould3 Step Historic Brickmould
and Reserve)(Traditional, Contemporary,
Architect Series Double Hung[2
8]1
1/8"
[50]2"
[36]1 3/8"
EXISTING CONSTRUCTION[4
8] (+
/-)1
7/8"
EXISTING CONSTRUCTION
[48]
(+/-)
1 7/
8"
EXTERIOR TRIM - HISTORIC RENOVATION APPLICATION
Aluminum Brickmould
Aluminum Brickmould Clip
Historic Brickmould Extruded Frame Expanders
*This configuration of extruded brickmould and break metal sill cover has previously been approved for use with historic projects. It is available through custom quoting as noted below. Please verify approval with local historic review board prior to ordering. Custom variations are available upon request.
W-IA-29Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Factory Installed Guidelines• Maximum size is 138" x 101"
• Trim comes assembled and installed on unit and includes endcaps and fins as neccessary.
• Factory Applied Trim is available on all Aluminum Clad products, including curved and angled shapes, with the following exceptions:
� Architect Series® and Designer Series® four-panel patio doors
� ProLine® hinged and sliding doors
� Precision Fit® pocket replacement windows
� Bay / Bow windows
� Architect Series® Specialty windows
ENDURACLAD® EXTERIOR TRIM - FACTORY APPLIED
Trim Profiles
Scale 3" = 1' 0"
RENOVATION REPLACEMENT FINNEW CONSTRUCTION FIN
50HEReplacement FinStandard Clad Trim
50HJReplacement Sill FinStandard Clad Trim
50H9Replacement FinClad Trim
70F4Trim Sill FinStandard Clad
50HBTrim FinStandard Clad
70F2Trim FinStandard Clad
[21]
13/1
6"[6
7]2
5/8"
[30]
1 3/
16"
[51]2"
[30]1 3/16"
[30]
1 3/
16"
[25]1"
[30]1 3/16"
[25]1"
[13]
1/2"
[8]5/16"
[89]
3 1/
2"
[34]1 3/8"
[89]
3 1/
2"
[40]1 9/16"
[89]
3 1/
2"[57]
2 1/4"
[37]
1 1/
2"
[55]2 3/16"
[37]
1 1/
2"
[40]1 9/16"
[18]
11/1
6"
[10]
3/8"
[36]1 7/16"
[18]
11/1
6"
[10]
3/8"
[58]2 5/16"
[18]
11/1
6"
[8]
5/16
"
[50]2"
[18]
11/1
6"
[6]
1/4"
[43]1 11/16"
SILL NOSE
TRIM PROFILES
HEAD DRIP CAP
50NNMonroe
50GCJefferson
50GUStandard
50NM3 1/2" Flat Casing
50GJ3 1/2" Flat Casing
50NLJefferson
50GFMonroe
50G93 1/2" Brickmould
70F5Brickmould
50MD3 1/2" Flat Casing
50H1, 50H8w/ Nose Extension2" Nose
50H0, 50H8w/ Nose Extension1" Nose
50GZ1/2" Nose
1/2" Sill Nose 1" Sill Nose 2" Sill Nose 3-1/2"
Flat Casing
SILL NOSE COMPATIBILITY
1-1/2" Brickmould ● ● ●
3-1/2" Brickmould ● ● ●
3-1/2"Flat Casing ● ● ● ●
Jefferson ● ●
Monroe ● ●
W-IA-30Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
ENDURACLAD® EXTERIOR TRIM - FACTORY APPLIED
Ordering Information
These dimensions do NOT include 3/8" per side for sealant, foam and backer rod, only the dimension of the trim beyond the unit frame.
Head to Jamb joints are mitered except for 3-1/2" Flat Casing, which uses butt joints and head end caps.
All applied trim includes end caps as needed and installation fin as determined by your selections (new construction or replacement/renovation).
3-1/2" Trim fins are used for flashing purposes only, and are not intended for anchoring/attachement of the unit.
Performing whole unit field application of EnduraClad Exterior Trim in the field may result in voiding product warranties.
All example images on this page use 1-1/2" Brickmould with 1/2" Sill nose
Jamb pieces are mitered to the slope of the sill. The sill is notched where the jambs meet the sill. Sill nose extensions are included where needed. Sill end caps are included..
A &
B
C
FR.
CB
A AFR.
A B C
Jamb (single) Head 3-1/2" Flat Casing Sill 1/2" Sill Nose 1" Sill Nose 2" Sill Nose
FRAME TO EXTERIOR TRIM1-1/2" Brickmould + 1.18" + 1.18" — + 1.18" + 1.892" + 2.892"3-1/2" Brickmould + 3.21" + 3.21" — + 1.18" + 1.892" + 2.892"3-1/2" Flat Casing + 3.21" + 3.21" + 3.21" + 1.18" + 1.892" + 2.892"Jefferson + 3.21" + 3.21" — — + 1.892" + 2.892"Monroe + 1.18" + 1.18" — — + 1.892" + 2.892"
W-IA-31Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
[3]
1/8"
[23]
15/1
6"
FRA
ME
[10]
3/8"
RO
UG
H O
PE
NIN
G
FRA
ME
[10]
3/8"
[3]
1/8"
[24]
15/1
6"R
OU
GH
OP
EN
ING
[29]
1 3/
16"
[2]
1/16
"[8
]5/
16"
[15]
9/16
"[8
]5/
16"
[30]
1 3/
16"
[25]
15/1
6"[1
3]1/
2"
1/2" SILL NOSE
BRICKMOULD
[23]7/8"
[21]13/16"
[34]
1 5/
16"
[25]
15/1
6"
[42]1 5/8"
[37]
1 1/
2"
[23]
15/1
6"
[3]
1/8"
RO
UG
H O
PE
NIN
G
[10]
3/8"
FRA
ME
HEAD
JAMB
SILL
Scale 6" = 1' 0" Scale 3" = 1' 0"
ENDURACLAD® EXTERIOR TRIM - FACTORY APPLIED APPLICATION
Brickmould with 1/2" Sill Nose
Siding Applications
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
W-IA-32Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 6" = 1' 0" Scale 3" = 1' 0"
FRA
ME
[10]
3/8"
[10]
3/8"
[30]
1 3/
16"
RO
UG
H O
PE
NIN
G
MA
SO
NR
Y O
PE
NIN
G
[18]
11/1
6"
[10]
3/8"
MA
SO
NR
Y O
PE
NIN
G
[29]
1 3/
16"
RO
UG
H O
PE
NIN
G
[10]
3/8"
FRA
ME
FRA
ME
[10]
3/8"
[10]
3/8"
[30]
1 3/
16"
RO
UG
H O
PE
NIN
G
MA
SO
NR
Y O
PE
NIN
G
brick around opening.excess mortar when placingProtect units and trim from
[6]
1/4"
[43]1 11/16"
Standard
[29]
1 3/
16"
[2]
1/16
"[8
]5/
16"
[15]
9/16
"[8
]5/
16"
[30]
1 3/
16"
[25]
15/1
6"[1
3]1/
2"
1/2" SILL NOSE
BRICKMOULD
[23]7/8"
[21]13/16"
[34]
1 5/
16"
[25]
15/1
6"
[42]1 5/8"
[37]
1 1/
2"
HEAD
JAMB
SILL
ENDURACLAD® EXTERIOR TRIM - FACTORY APPLIED APPLICATION
Brickmould with 1/2" Sill Nose
Brick Veneer Applications
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
W-IA-33Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 6" = 1' 0" Scale 3" = 1' 0"
ENDURACLAD® EXTERIOR TRIM - FACTORY APPLIED APPLICATION
Brickmould with 1/2" Sill Nose
Replacement Brick Veneer Applications
SHIM AND LEVEL UNITS AS REQUIRED
CONTINUOUS WOOD BLOCKING, WOOD TRIM, BACKER ROD AND SEALANT BY OTHERS
[10]
3/8"
MA
SO
NR
Y O
PE
NIN
G
[29]
1 3/
16"
RO
UG
H O
PE
NIN
G
[10]
3/8"
FRA
ME
FRA
ME
[10]
3/8"
[10]
3/8"
[30]
1 3/
16"
RO
UG
H O
PE
NIN
G
MA
SO
NR
Y O
PE
NIN
G
FRA
ME
[10]
3/8"
[10]
3/8"
[30]
1 3/
16"
RO
UG
H O
PE
NIN
G
MA
SO
NR
Y O
PE
NIN
G
[29]
1 3/
16"
[2]
1/16
"[8
]5/
16"
[15]
9/16
"[8
]5/
16"
[30]
1 3/
16"
[25]
15/1
6"[1
3]1/
2"
1/2" SILL NOSE
BRICKMOULD
[23]7/8"
[21]13/16"
[42]1 5/8"
[37]
1 1/
2"
HEAD
JAMB
SILL
W-IA-34Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
ATTACHMENT OPTIONS
Receptor and Subframe Systems
T-Subframe Application
[73]
MA
X.
2 7/
8"
EX
ISTI
NG
OP
EN
ING
[16]
5/8"
SU
BFR
AM
E
MA
SO
NR
Y O
PE
NIN
G
[73]
MA
X.
2 7/
8"
EX
ISTI
NG
OP
EN
ING
FRA
ME
[10]
3/8"[1
6]5/
8"
[165]6 1/2"
SU
BFR
AM
E
[10]
3/8"
FRA
ME
MA
SO
NR
Y O
PE
NIN
G
[19]
3/4"
SU
BFR
AM
E
[89]
3 1/
2"[7
6]3"
[58]
MA
X.
2 1/
4"
FRA
ME
EX
ISTI
NG
OP
EN
ING
MA
SO
NR
Y O
PE
NIN
G
CLIP #7363
#72F6T-SUBFRAME HEAD
#7363SUBFRAME CLIP
CLIP #7363
#73H9T-SUBFRAME JAMB
#8x5/8" PAN HEAD PHILLIPS SCREWWINDOW CLIP #5027 AND
PACKAGE #0DB00000:
field-cut as required.*NOTE: Subframe leg may be
#73H8T-SUBFRAME SILL
[89]
3 1/
2"
and Steel Frame.Existing Wall Construction
Steel Frame.Existing Wall Construction and
Steel Frame.Existing Wall Construction and
HEAD
JAMB
SILL
W-IA-35Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
ATTACHMENT OPTIONS
Receptor and Subframe Systems
Standard Subframe Application
[204]8"
installation instructions)Continuous Perimeter Sealant (See
SU
BFR
AM
E
MA
SO
NR
Y O
PE
NIN
G
[73]
MA
X.
2 7/
8"E
XIS
TIN
G O
PE
NIN
G
FRA
ME
[10]
3/8"[1
6]5/
8"S
UB
FRA
ME
[91]
MA
X.
3 9/
16"
FRA
ME
EX
ISTI
NG
OP
EN
ING
MA
SO
NR
Y O
PE
NIN
G
SU
BFR
AM
E
[89]
3 1/
2"[8
9]3
1/2"
[90]
3 9/
16"
MA
SO
NR
Y O
PE
NIN
G
[73]
MA
X.
2 7/
8"E
XIS
TIN
G O
PE
NIN
G
FRA
ME
[10]
3/8"[1
6]5/
8"
be field-cut as required.*NOTE: Subframe leg may
SUBFRAME SILL #7360
PHILLIPS SCREWCLIP #5087 AND #8x5/8" PAN HEADPACKAGE #0B050000: WINDOW
SUBFRAME HEAD #7355
SUBFRAME JAMB #7357
SUBFRAME CLIP #7363
AND WOOD WINDOW FRAMEEXISTING WALL CONSTRUCTION
JAMB
HEAD
AND WOOD WINDOW FRAMEEXISTING WALL CONSTRUCTION
AND WOOD WINDOW FRAMEEXISTING WALL CONSTRUCTION
SILL
Scale 3" = 1' 0"
W-IA-36Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
ATTACHMENT OPTIONS
Receptor and Subframe Systems
Expander and Trim Application
Scale 3" = 1' 0"
W-IA-37Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
The Pella accessory system includes all of the most-often-specified standard items shown in this Architectural Design Manual as well as
other specials shown here.
In addition, completely custom / special installation, panning, and trim systems can be designed and fabricated by Pella for specific
project requirements. Shapes shown on the next two pages can be ordered to various dimensions needed. Consult your local Pella
sales representative.
BREAK METAL
Covers and Trim
MULLION COVERS
HEAD JAMB TRIM
MULLION TRIM SILL TRIM
W-IA-38Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
BREAK METAL
Sill Flashing
SILL FLASHING
ATTACHMENT CLIP
W-IA-39Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Custom Aluminum Sil l Flashing• Custom 0.050" (1.27) aluminum sill flashings can
be fabricated to specifications as required. Detail shows typical conditions where custom aluminum sill flashing might be used.
• The use of this sill flashing is recommended only in climates where thermal conductance is not likely to occur.
• Where aluminum comes into contact with cement materials or steel, apply protective coating to separate galvanically incompatible materials.
Scale 3" = 1' 0"
BREAK METAL
Sill Flashing Application
W-IA-40Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
WOOD EXTERIOR
Exterior Mullion Covers
Scale 3" = 1' 0"
INTERIOR MULLION COVERS
Accessory Indiv. Part No.
BoxNo.
Casement Interior 26A9 09GK
Double-Hung Interior 2600 0BMU
Bay Interior 3015 0B42
EXTERIOR MULLION COVERS
Accessory Indiv. Part No.
BoxNo.
Casement Exterior–Horizontal 2903 0B97
Casement Exterior–Vertical 2942 0921
Double-Hung Exterior–Horizontal 29T0 —
Double-Hung Exterior–Vertical 3046 06M2
Bow Casement Exterior 3149 0B44
See the Bay/Bow Section in the Architectural Design Manual for application details.
W-IA-41Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
SUBSILLS AND EXTERIOR TRIM
Accessory Indiv. Part No.
BoxNo.
3-1/2" with Rabbet 38L6 0F08
3-1/2 " without Rabbet 38L5 0F07
3-1/2" Flat Casing with Rabbet 380R 0DAZ
1-7/8" Curved with Rabbet 33M4 —1-7/8" Curved without Rabbet 33P2 —1-7/8" with Rabbet 3443 0B96
1-7/8" without Rabbet 3419 0BB0
Accessory Indiv. Part No.
BoxNo.
1-1/8" Subsill 3544 0920
1-7/8" Subsill 250H 093H
Double-Hung Sill Nose 3315 0C29
Sill Flashing — 0D98
WOOD EXTERIOR
Brickmould and Subsill
Scale 3" = 1' 0"
W-IA-42Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INTERIOR TRIM
Casing
Scale 3" = 1' 0"
[16]5/8"
[19]3/4"
[19]3/4"
[19]3/4"
[19]3/4"
[64]
2 1/
2"
[64]
2 1/
2" [89]
3 1/
2"
[89]
3 1/
2"
[83]
3 1/
4"
[83]
3 1/
4"
[64]
2 1/
2"
[64]
2 1/
2"
[64]
2 1/
2"
[64]
2 1/
2"
[64]
2 1/
2"
[89]
3 1/
2"
[89]
3 1/
2"
[70]
2 3/
4"
[64]
2 1/
2"
[19]3/4"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[16]5/8"
[83]
3 1/
4"
[11]7/16"
[16]5/8"
[108
]4
1/4"
[64]
2 1/
2" [89]
3 1/
2"
[57]
2 1/
4" [70]
2 3/
4"
[76]3"
[89]
3 1/
2"
[83]
3 1/
4"
[76]3"
[64]
2 1/
2"
[16]5/8"
[89]
3 1/
2"
[16]5/8"
[83]
3 1/
4"[5
7]2
1/4"
[64]
2 1/
2"
30AX, 30BB2 1/2" 1
30NY2 1/2" 3
30NX, 312Q2 1/2" 2
31TY2 1/2" 4
31TZ2 1/2" 5
31U02 1/2" 6
31U23 1/4" 1
30AZ, 312R3 1/2" 1
30NW, 312S3 1/2" 2
31U43 1/2" 3
31U53 1/2" 4
31U63 1/2" 5
31UB3 1/4" 1
31UC3 1/4" 2
31UD3 1/4" 3
31UE3 1/2" 2
30BA3 1/2" 1
30AY, 30BD2 1/2" 1
31U72 1/2" 2
31UF2 1/2" 3
31UA3" 1
31U93 1/4" 1
30U7, 30UA3 1/2" 1
31U83 1/2" 2
31UN4 1/4" 1
31UM3 1/2" 1
31UH3" 2
31UG3" 1
31U12 3/4" 2
31UL2 3/4" 1
31UK2 1/2" 2
31UJ2 1/2" 1
31UP2 1/4" 1
31U32 1/4" 1
PROVINCIAL
CRAFTSMAN
RANCH
COLONIAL
W-IA-43Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INTERIOR TRIM
Trim Accessories
[19]3/4"
[19]3/4"
[19]3/4"
[19]3/4"
[9]5/16"
[45]
1 25
/32"[6]
1/4"
[29]
1 5/
32"
[3]
1/8"
[13]
1/2"
[3]
1/8"
[13]
1/2"
[3]
1/8"
[13]
1/2"
[3]
1/8"
[16]
5/8"
[16]
5/8"
[13]
1/2"
[16]
5/8"
[16]
5/8"
[6]1/4"
[129
]5
1/8"
[6]1/4"
[91]
3 5/
8"[6]1/4"
[36]
1 3/
8"
[6]1/4"
[6]1/4"
[6]1/4"
[6]1/4"
[6]1/4"
[6]1/4"
[6]1/4"
[6]1/4"
[16]
5/8"
[16]5/8"
[16]5/8"
[16]
5/8"
[10]
3/8"
[67]2 5/8"
[67]2 5/8"
[113]4 7/16"
[41]1 5/8"
[41]1 5/8"
[113]4 7/16"
[62]2 7/16"
[41]1 5/8"
[41]1 5/8"
[62]2 7/16"
[32]
1 1/
4"
[41]1 5/8"
[16]
5/8"
[13]
1/2"
[19]
3/4"
[19]
3/4"
[12]
1/2"
[41]1 5/8"
[12]1/2"
[64]
2 1/
2"
[133
]5
1/4"
[16]5/8"
[35]1 3/8"
[47]1 13/16"
[22]7/8"
[44]1 3/4"
[22]7/8"
[16]
5/8"
[10]
3/8"
[129
]5
1/8"
[117
]4
5/8"
[104
]4
1/8"
[91]
3 5/
8"
[79]
3 1/
8"
[66]
2 5/
8"
[53]
2 1/
8"
[36]
1 3/
8"
31VWOgee 2
31VSOgee 2
30LCRound 2
3204Round 2
32WJOgee 1
31VROgee 1
32WHRound 1
3146Round 1
#2600DOUBLE-HUNG
#26A9CASEMENT
261CLattice 5
260PLattice 4
260ALattice 3
Jamb6 9/16"
Jamb4 9/16"
STOOL
COVE MOULDBASE TRIM
SPREAD MULLION COVER
LATTICE
STOP
261C4" Mullion 1
261B3 1/2" Mullion 1
260V3" Mullion 1
260P2 1/2" Mullion 1
260N2" Mullion 1
260D1 1/2" Mullion 1
260B1" Mullion 1
260A1/2" Mullion 1
30U5 / 30U8Quarter Round 1
31VVLattice 2
60U6 / 60U9Cove Trim 1
31VPLattice 1
31VQQuarter Round 2
31VLColonial 2
30VGColonial 4
31VFColonial 3
30VMColonial 1
30VJRound 1
31VHRound 2
31VKRanch 1
31VNSquare 1
Scale 3" = 1' 0"
W-IA-44Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INTERIOR TRIM
ReadyTrim
A
(INTERIOR VIEW SHOWN)
B
(EXTERIOR VIEW SHOWN)
B
A
Ready Trim Plus Ready Trim Plus w/Stool & Apron
(EXTERIOR VIEW SHOWN)
B
A
Ready Trim
FORMULAS
READY TRIM: A = FRAME WIDTH + (2 x TRIM WIDTH - .905”) B = FRAME HEIGHT + (2 x TRIM WIDTH - .874”)
READY TRIM PLUS: A = FRAME WIDTH + (2 x TRIM WIDTH - .625”) B = FRAME HEIGHT + (2 x TRIM WIDTH - .625”)
READY TRIM PLUS WITH STOOL & APRON: A = FRAME WIDTH + (2 x TRIM WIDTH - .625”) B = FRAME HEIGHT + (2 x TRIM WIDTH - .187”)
MINIMUM FRAME DIMENSION ALLOWED IS: 12.000” x 12.000”
MAXIMUM FRAME DIMENSION ALLOWED IS: 62.500” x 74.500” OR 74.500” x 62.500
Pine Oak
Ready Trim
Ready Trim Knockdown
(lineals)
Ready Trim
Ready Trim Knockdown
(lineals)
READY TRIM PROFILE OPTIONS
RA
NC
H
30AY 2-1/2” Ranch 1 ● ● ● ●
31U7 2-1/2” Ranch 2 ● ● ● ●
31UF 2-1/2” Ranch 3 ● ● ● ●
31UA 3” Ranch 1 ● ●
31U9 3-1/4” Ranch 1 ● ● ● ●
30U7 3-1/2” Ranch 1 ● ● ● ●
31U8 3-1/2” Ranch 2 ● ● ● ●
CR
AFT
SMA
N 31UB 3-1/4” Craftsman 1 ● ● ● ●
31UC 3-1/4” Craftsman 2 ● ● ● ●
31UD 3-1/4” Craftsman 3 ● ●
30BA 3-1/2” Craftsman 1 ● ● ● ●
31UE 3-1/2” Craftsman 2 ● ● ● ●
CO
LON
IAL
31U3 2-1/4” Colonial 1 ● ● ● ●
30AX 2-1/2” Colonial 1 ● ● ● ●
30NX 2-1/2” Colonial 2 ● ● ● ●
30NY 2-1/2” Colonial 3 ● ● ● ●
31TY 2-1/2” Colonial 4 ● ● ● ●
31TZ 2-1/2” Colonial 5 ● ● ● ●
31UO 2-1/2” Colonial 6 ● ● ● ●
31U2 3-1/4” Colonial 1 ● ● ● ●
30NW 3-1/2” Colonial 2 ● ● ● ●
31U4 3-1/2” Colonial 3 ● ● ● ●
31U5 3-1/2” Colonial 4 ●
31U6 3-1/2” Colonial 5 ●
PRO
VIN
CIA
L
31UP 2-1/4” Provincial 1 ● ● ● ●
31UJ 2-1/2” Provincial 1 ● ●
31UK 2-1/2” Provincial 2 ● ●
31UL 2-3/4” Provincial 1 ● ●
31U1 2-3/4” Provincial 2 ● ●
31UG 3” Provincial 1 ● ●
31UH 3” Provincial 2 ● ● ● ●
31UM 3-1/2” Provincial 1 ●
31UN 4-1/4” Provincial 1 ●
Ready Trim Ready Trim Plus Ready Trim Plus with optional Stool
and Apron
Pine profiles available prefinished primed, painted or stained.
Oak profiles available prefinished with stain.
READY TRIM READY TRIM PLUS
For use with or without Jamb Extensions
4 pieces of trim, Pre-Assembled
Packaged by unit, max 3 per carton
Save time when Jamb Extensions are needed
4 pieces of trim, 4 Jamb Extensions, 4 Cover Strips, Pre-Assembled
Packaged by unit, max 1 per carton
Optional Stool and Apron available.
READY TRIM KNOCKDOWN
READY TRIM PLUS KNOCKDOWN
Pre-measured and kitted to save time
4 pieces of trim with 10” excess, Unassembled, Unmitered
Kitted by Order
Pre-measured and kitted to save time
4 pieces of trim and 4 Jamb Extensions with 10” excess, Unassembled, Unmitered
Optional Stool (with 14" excess) and Apron available.
Kitted by Order
Rev. 3/16/2015
W-IA-45Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INTERIOR JAMB EXTENSIONS
AccessoryIndiv.
Part No. (Straight)
Box No.
(Straight)
Indiv. Part No. (Curved)
Box No.
(Curved)
3/8" Jamb Extension 250R 0654 — —3/4" Jamb Extension — — 28CU 0BM7
27/32" Jamb Extension 283G 0930 28EA 0BUL
1-1/2" Jamb Extension 301E 0648 30K7 0BUK
2" Jamb Extension with Holes 31J1 — — —2" Jamb Extension 311M 06EN — —2-3/8" Jamb Extension 311Q 06EP — —2-27/32" Jamb Extension 311J 06ER 31A9 0BUJ
3-1/2" Jamb Extension 324A 06ET 32EK 0BUH
3-1/2" Jamb Extension with Holes 3268 0C83 32EL 0BM6
5-1/2" Jamb Extension 30NR 00YX — —
Scale 3" = 1' 0"
INTERIOR TRIM
Jamb Extensions
W-IA-46Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
AZEK® exterior composite trim is available for window applications in 1/16" increments provided factory pre-assembled, pre-cut knock-down (when either or both frame height or width > 75") and in lineal (9') lengths for field assembly. Order pre-assembled and pre-cut by actual window frame size.
CUSTOM AZEK® EXTERIOR SURROUND TRIM SHAPES
Window Shapes
W-IA-47Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
AZEK® exterior composite trim is available for window applications in 1/16" increments provided factory pre-assembled, pre-cut knock-down (when either or both frame height or width > 75") and in lineal (9') lengths for field assembly. Order pre-assembled and pre-cut by actual window frame size.
Not all shapes are available on every unit. See your local sales representative for availability.
Description Part #
2" Brickmould AZEK® trim 9 ft 0E5B
3-3/8" Flat casing AZEK® Trim 9 ft 0E5U
4-3/8" Flat casing AZEK® Trim 9 ft 0E5U0001
Sill nose AZEK® Trim 9 ft 0E6S
Crown mould AZEK® Trim 9 ft 0E5Z
Scale 3" = 1' 0"
AZEK® EXTERIOR SURROUND TRIM SHAPES
W-IA-48Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
AZEK® exterior composite trim is available for door applications in 1/16" increments provided factory pre-cut in three knock-down pieces (no sill needed) and in lineal (9’) lengths for field assembly. Order by actual door frame size.
Not all shapes are available on every unit. See your local sales representative for availability.
CUSTOM AZEK® EXTERIOR SURROUND TRIM SHAPES
Entry and Patio Door Shapes
W-IA-49Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 3" = 1' 0"
• Refer to the appropriate Pella installation instruction for step by step instructions.
2" AZEK® BRICKMOULD WITH SILL NOSE
Installation Details
Double-Hung with Brick Veneer
W-IA-50Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 3" = 1' 0"
• Refer to the appropriate Pella installation instruction for step by step instructions.
2" AZEK® BRICKMOULD WITH SILL NOSE
Installation Details
Casement with Stucco
W-IA-51Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 3" = 1' 0"
• Refer to the appropriate Pella installation instruction for step by step instructions.
3-3/8" FLAT CASING WITH SILL NOSE AND CROWN
Installation Details
Double-Hung with Wood Siding
W-IA-52Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 3" = 1' 0"
3-3/8" FLAT CASING WITH SILL NOSE AND CROWN
Installation Details
Casement with Stucco
W-IA-53Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
Scale 3" = 1' 0"
3-3/8" FLAT CASING WITH SILL NOSE AND CROWN
Installation Details
Double-Hung with Brick Veneer
W-IA-54Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSRenovation — Exterior Pocket Installation
• Fully assembled standard double-hung window• Slides easily into existing pocket from the exterior• Trim, wall coverings, paint and plaster are usually not disturbed• Eliminates cost and inconvenience of a complete tear-out• Installs from the exterior
HEAD
JAMB
SILL
Scale 3" = 1' 0"
W-IA-55Pella 2017 Architectural Design Manual | Division 08 – Openings | Windows and Doors | www.PellaADM.com
INSTALLATION ACCESSORIES
INSTALLATION SYSTEMSRenovation — Precision Fit® Interior Pocket Installation
[6]
1/4"
MA
KE
HE
IGH
T[6
]1/
4"M
AK
E H
EIG
HT
[6]1/4" MAKE WIDTH
JAMB
SILL
HEAD
HEAD
JAMB
SILL
• Fully assembled Precision Fit® double-hung, awning or casement window
• Slides easily into existing pocket from the interior• Trim, wall coverings, paint and plaster are usually not
disturbed• Eliminates cost and inconvenience of a complete tear-out• Installs from the interior
Scale 3" = 1' 0"