INSTALL GUIDE - storage.googleapis.com · Recommended Installation Procedures Mounting the Module...

WWW.ULTRASTARTERS.COM

FCC/ID NoticeThis device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation.CAUTION: Changes or modifications not expressly approved by the part responsible for compliance void the user’s authority to operate this devise.

INSTALL GUIDE

Technical Support- 866.698.5872

640 Series Advanced Remote Vehicle

Security System

Table of Contents ComponentsWiring Diagram Page 3Installation Tips Page 4Pre-Installation SuggestionsInstallation Suggestions Page 4Mounting The ModuleInstalling The Program ButtonConnecting The Starter DisableConnecting The Dome Light Supervision Under Hood ConnectionsMounting The SirenWire Connectors Page 513 Pin Main Harness Connector4 Pin Red Connector- Keyless Entry4 Pin Additional Sensor Input2 Pin Starter Disable ConnectorInstallation Page 6-7Basic Installation - Quick startShock Sensor ProgrammingTest The SystemProgramming Page 7-9Program Overview & System ResetProgram Menu 1 (User Settings)Program Menu 2 (Alarm Settings)Operations Page 10Single & Dual Car OperationTransmitter ProgrammingBattery Replacement Other Features Page 11System Service ModeService Mode- By remoteDiagnostics Page 12

- Control Module - Starter Disable Harness - Two 4 Button AM Transmitters - 4 pin Aux Sensor Harness - Multi-Tone Siren - AM 2way Antenna With Integrated - 13 Pin Main Harness LEDs and Program/Valet Switch - Installation and Owner Manuals - Window Decal - 4 Pin Keyless Entry Harness With Driver’s Door Priority Output

Components

Table of Contents

PAGE 2

SECURITY SYSTEMINSTALL GUIDE

GreenRedBlue

Blue

Pink

Lock Output

Unlock Output12vts Low Current

2nd Unlock

(-)500ma

(-)500ma(-)500ma

(+)500ma Programmable Output

Programmable OutputProgrammable Output

Voltage Inverter Output

Sensor Full - Warn(-)500ma Input(-) trigger Input

SIDE VIEW

REAR VIEW

**500ma outputs are low current and are designed to activate relays.

Built-in Starter Disable Relay (Normally Connected 87a & 30)

Wiring Diagram

PAGE 3

SECURITY SYSTEM INSTALL GUIDE

Switched Ignition Ignition Input(+) Input

(-) Door Input(-) InputNegative Door Pin

(+) Door Input(+) InputPositive Door Pin

Hood Input(-) InputHood Pin Switch

(+) Siren3amp Siren Output (+)

(-) When Armed500ma (-) While Armed

Dome Light Dome Light Output 500ma

(-) Trunk Release (-) Trunk Release500ma

(+) Park Lights15ampPark Lights

Chassis Ground Ground(-) Input

Constant Power Main Power(+) Input

Horn/ Channel 5500maProgrammable

Channel 4500ma Programmable

ACTIVE RF ANTENNA** Status Led’s

Program Button**The antenna MUST be connected for the system to operate

Green

Purple

Blue

Brown

Orange

Blk/White

Grey

White

Black

Red

Pink

Wht/Blue

Yellow

Green

RedBlack

Sensor Pre - WarnSensor GroundSensor Power

(-)500ma Input(-)500ma Output(+)500ma Output

(-) trigger Input Ground Output 12volt Output

Auxiliary Sensor Connector This connector can be used to add additional Alarm Sensors such as Radar, Glass Break or an additional shock sensor for coverage at the rear of the vehicle.

Recommended Installation Procedures

Mounting the Module

Installing The Antenna

Connecting The Starter Disable

BEFORE STARTING INSTALLATION:- Discuss the optional system features with the customer.- Take a few minutes to review the installation and owners manuals.- Do a walk around the vehicle and check for any damage. - If installing a LED discuss the placement with customer before installing.

Never mount the module in the engine compartment. Select a location under the dash to install the main module. Be certain that the module is securely attached and does not obstruct any serviceable areas. Mount the module so that it cannot be seen if looking under the dash as it could be easily unplugged by a thief. The module must be free from all moving parts such as brake, clutch and gas pedals linkages.

The antenna should be mounted in the top center of the windshield with the antenna mastfacing downwards. First ensure that the glass is clean and dry, remove the plastic from theadhesive tape then press against the glass.

This system contains a built-in Starter disable relay. The brown starter kill wire from the wire harness bag will connect to the module as normally connected. (87a & 30)Cut the brown wire in half, then locate the vehicles starter wire. This wire will switch to12volts in the crank/start position only. Cut this wire in half and confirm that the vehicle will not start. Connect the brown wires, one to each side of the cut starter wire. Route the brown wires to the main module and connect.

This output can be used to activate the interior lights upon disarming the alarm, connectthis output to a relay to activate the interior light. The dome light output will stay active for 30 seconds upon disarm.

Recommended Pre-Installation Procedures

Mounting The Siren

Choose a location in the engine compartment that is away from high sources of heat and direct exposer to water. The siren should be mounted as well as grounded to solid metal. Run the wiring for the siren so that it can not be seen or reached from below thevehicle.

PAGE 4


Brown (+) Siren Output Positive output for siren*Pink Channel 4 Output Programmable - See menu 2**Wht/Blue Channel 5 Output Programmable - See menu 2***Red Main Power Input Constant 12 Volt inputBlack Ground Input System ground inputGrey (-) Trunk Release Negative trunk release. 500ma****White (+) Park lights Programmable - 10amp Maximum Orange (-) When Armed Negative output when system is armed****Blk/White (-) Dome Light Dome light supervision****Purple (+) Door Input Positive door pin switch inputGreen (-) Door Input Negative door pin switch inputBlue (-) Hood Input Negative input from hood pin switchYellow Ignition Input Input from vehicles ignition wire

Green Door Lock Programmable - menu 1, setting 3.Red 12 Volt Output Output for voltage inverter only*****Blue Door Unlock Programmable - menu 1, setting 3.Pink Second Unlock Programmable - menu 1, setting 3******

4 Pin Connector Red

4 Pin Connector Blue

4 Pin Connector White

This connector is for the RF antenna. The antenna also contains 2 LEDs and the Program Button.

Blue Sensor Full Warn Input trigger for addition alarm sensor(s)Green Sensor Pre Warn Input trigger for addition alarm sensor(s)Black Ground Output Ground output for addition alarm sensor(s)Red 12 Volt Output 12 volt output for additional alarm sensor(s)

* This output is designed to operate one siren. If more than one is being added, a relay must be installed to avoid damaging the module.**Channel 4 is activated by holding the Star button on the transmitter.*** Channel 5 must be programmed to activate on the # button. This channel works on the horn output, if the 5th channel is programmed the horn output will function as 5th Channel.****500ma outputs are low current and are designed to activate relays.*****This is a low current 12volt output designed for use with a voltage inverter. ******This output will activate on the second press of unlock within 3 seconds.

14 Pin Connector

PAGE 5


2 Pin Connector (Brown wire with female connectors)

Starter Disable harness. See page 4 for installation instructions

13 Pin Power Connector

Step 2- Plug-In The Module

Step 3- Program, Test And Adjust The Shock Sensor

Test The System

When all the connections are done, the control module can be plugged in. Before connecting the control module, make sure the ignition is in the OFF position. Plug in the 6 pin harness then the 14 pin followed by any other connectors that were used.

Black Ground Input System ground input.Yellow Ignition Input Input from vehicles ignition wire. Red Main Power Input Constant power inputWhite (+) Park lights Programmable - menu 2, setting 3.Brown (+) Siren Output Positive output for siren.Green* (-) Door Input Negative door pin switch input.Purple* (+) Door Input Positive door pin switch input.

*Test for door pin type (Positive or Negative) then connect the appropriate wire (Green or Purple)

To program the Shock Sensor.1.Press and hold the Lock and Unlock buttons for 5 seconds.2.The system will chirp and the park lights will flash three times then stay “ON”.3.Within 10 seconds impact vehicle in a safe place (i.e. - Window pillar) with amount of force wanted to activate alarm. The siren will chirp upon learning the impact.4. The Shock Sensor is now programmed.5. Press the Unlock button to exit the Program Mode.To test the Shock Sensor.1. Press the Lock button once to arm the system.2. Wait five seconds then impact the vehicle. Lighter impacts to the vehicle should trigger the warn away (The siren will chirp three times). A harder impact to the vehicle will trigger the full alarm.(The siren will activate for 60 seconds then turn off). 3. To deactivate the alarm when triggered, press the unlock button twice. To adjust the Shock Sensor.1. Repeat the shock sensor learning.- If the sensor was to sensitive, impact the vehicle with greater force.- If the sensor was not sensitive enough, impact the vehicle with less force.*For best results ensure that the Control Module is mounted securely to the vehicle.

1. Open all the vehicles windows. 2. Press the Lock button to arm the system.3. Wait five seconds (or until the dome light goes out) then reach in through a window and open the door. The alarm will then activate (repeat on all the doors).4. Test the Shock Sensor again and adjust if necessary.5. Insure that all additional features are working as intended.6. If necessary proceed to Program Mode to adjust the programmable outputs.

Quick Start Install

Step 1 - Connect All Of the Following Wires

Your Basic Install Is Complete!

PAGE 6


Program mode allows you to adjust the settings and options of your system. Your system has been intelligently designed by installers with years of experience. The system’s default settings do not require any program changes in most cases. However, this system does incorporate a highly advanced programming system that includes 2 menus with numerous options and settings that can be easily adjusted for custom installations and applications.

Entering Program Mode

Changing the Programmable Settings

To Enter Program Mode1) Make sure ignition is in the off position.2) Within three seconds turn the key ON - OFF - ON - OFF - ON. Leave Key ON.3) Press and release the Program Button one time.4) Park lights will come and the siren will chirp to confirm entering Program Mode.5) Select Desired Program Menu by the following: Press Button #1 Lock User Options Page 8. Press Button #2 Unlock Alarm Settings Page 9.6) The selected mode will be confirmed by a siren chirp and one park light flash.7) The Program Menu may be changed at any time by pressing the transmitter buttons as above, this allows the installer to change a setting from one menu, then quickly jump to another menu and change another setting without exiting Program Mode.8) Program Mode will be exited if there is no activity for 30 second or if the key is turned to the “Off” position. This will be confirmed by one siren chirp and park light flash. Note: If unit does not enter Program Mode, turn ignition off and repeat steps 1-4. ** The ignition wire(Yellow) MUST be connected to the vehicle’s ignition wire. If it is not connected it will not be possible to enter the Program Modes.

To Select and Change A Program Setting:1) Enter Program Mode.2) Select the desired Program Menu. (See pages 8&9)3) Press & release the Program Button the correct number of times to select the desired Program Setting(as listed on pages (8&9). The park lights will flash and the siren will chirp to indicate the current setting that is selected.4) Press and hold the Program Button until the parking lights / siren confirm the selected setting. The park lights will flash and the siren will chirp to indicate the option selected within the setting.5) Turn the ignition key “Off” to exit Program Mode.

SYSTEM RESET

STEP 1 - Within three seconds turn the key ON-OFF-ON-OFF-ON (Leave the Key ON).STEP 2 - Press and release the Program Button.STEP 3 - Park Lights will come ONSTEP 4 - Press the Program Button a second time and hold for 8 seconds until the park lights flash 3 times and siren chirps 3 times.System is now re-set to factory defaults. NOTE: Reset to defaults does not delete the transmitters from memory.

Programming Overview

PAGE 7


Setting 1- Ignition Auto Lock

Menu 1 - User Settings

Setting 2- Horn Honk Settings

Setting 3- Door Lock Options

Setting 4 -Sensor - Enable / Disable

Setting 5 - Passive / Active Arming

Setting 6 - Active / Passive Locks

1 Double Pulse Unlock 1 Flash Single .75 second lock and double unlock pulse2 3 Second Lock & Unlock 2 Flashes 3 second pulses for lock & unlock*3 0.75 Second Pulses 3 Flashes 0.75 second pulses for lock and unlock

1 Passive Arming 1 Flash Auto Arms 30 seconds after last door is closed2 Active Arming With Rearm 2 Flashes Unlock is pressed and no door is within 30 sec.* 3 Active Arming 3 Flashes Alarm arm by remote transmitter only.

1 Sensors Disabled 1 Flash Shock sensor and Aux. Sensor disabled* 2 Sensors Enabled 2 Flashes Shock Sensor and Aux. sensor enabled.

1 Active Locking 1 Flash Doors do not auto-lock with passive arming*2 Passive Locks 2 Flashes Doors Auto-Lock with passive arming.

1 Ignition Lock & Unlock Enabled 1 Light Flash Doors Lock/Unlock when the key is turned On/Off2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only *3 Ignition Auto Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition key

1 Lock & Unlock chirps Disabled 1 Flash A audible chirp for Panic Mode only *2 Chirps Enabled 3 Flashes Chirp indication for all functions

Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.

Press the Program Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.





PAGE 8


Setting 1 - Car Finder/ 5th Channel

Menu 2- Alarm Settings

Setting 2 - Secure Program Mode

Setting 3 - Park Light Output

Setting 4 - Horn Honk Timing

Setting 5 - 4th Channel Settings

Setting 6 - Car Jack Mode

Setting 7 - Horn/ 5th Channel

1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled *2 Car Finder ON 2 Light Flashes Car Finder Mode activated when # button is held.**To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.

1 Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm2 Negative Park Light 2 Flashes Switches Park Light and the Trunk Release outputs 3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm

1 5ms Pulsed Output 1 Flash Short (Quiet) Pulses2 20ms Pulsed Output 2 Flashes Long (Loud) Pulses*3 10ms Pulsed Output 3 Flashes Normal (Medium) Pulses

1 Secure Program Active 1 Flash Ignition “ON” and Program switch held for 15 seconds2* Normal Program Active 2 Flashes Ignition “ON” and Program switch held for 5 seconds

Press the Program Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)Press and hold the Program Switch until you receive the appropriate # of park light flashes and/or siren chirps.Release the Program Switch. Press the Program momentarily to move to next program step or repeat to change selection.




1 Pulsed Output 1 Flash Pulsed for 0.75 seconds upon 4th Channel Activation2 Latched Output 2 Flashes Latched until repeated or ignition “ON”*3 Active Output 3 Flashes Active for as long as the button is held on Transmitter.

1 Type 1 1 Flash Press button #4 or open the door while the Ignition is “ON”2 Type 2 2 Flashes Press button #4 or by turning the Ignition “On”*3 Car Jack OFF 3 Flashes No Car Jack Functions

1 5th Channel 1 Flash Active for as long as the # button is held on Transmitter.2 LED Output 2 Flashes Pulsed output for addition LED activation*3 Horn Honk 3 Flashes Horn Honk with Arm & Disarm Chirps



Press the Star buttons to activate the 4th Channel output. The Shock Sensor and ignition will be bypassed upon 4th channel activation.

PAGE 9


Press Once to Lock the doors and arm the alarm. Hold for Panic Mode.Press a second time and hold for Constant Lock Output.

Press Once to Lock and arm the alarm. Hold for Panic Mode.Press a second time and hold for Constant Lock Output.

Press once to unlock the doors and disarm the alarm Press and hold for the Trunk / Aux Output

Press once to unlock the doors and disarm the alarm Press and hold for the Trunk / Aux Output

Press this button to activate the 4th channel output.This output can be used to activate additional alarm features.

Press this button to activate the 4th channel output.This output can be used to activate additional alarm features.

Press once and hold for Car FinderPress and release then hold to activate/deactivate Service Mode.

Press once and hold for Car FinderPress and release then hold to activate/deactivate Service Mode.

Second Car Operation (Optional)

First Car Operation

First Car

2nd Car

=

=

=

=

&

&

&then then

Step 1 - Within three seconds turn the ignition ON-OFF-ON-OFF-ON - Leaving ON.

Step 2 - Press and hold the Program Switch - Parking Lights will come ON **if parklights do not come on at this point, turn key off for 5 seconds, then repeat step 1.

Step 3 - Continue to hold the Program Switch, the park lights will turn off. (Continue holding the switch)

Step 4 - Press the LOCK button on each of 1st car remote’s and press the # buttonon Each of the 2nd car remote’s of the transmitters to be programmed pause for about 2-3 seconds between each remote. The park lights will Flash once and the siren will chirp once each time a new code is learned.

Note: Pause for no more than 2 seconds between transmitters All the transmitters to be used must be programmed at the same time. All transmitters not programmed at this time will be erased from memory for security. The system holds a maximum of 3 transmitter codes including 2nd car remote codes.You can program the same remote as a 1st car remote in one vehicle and as a 2nd carremote in a second vehicle.

Transmitter Programming

PAGE 10


When the Car Jack Mode is activated the system will start flashing the LED rapidly for five seconds. The park lights and siren will then activate once every second for 10 seconds in Countdown Mode. After 10 seconds the alarm will trigger into Full Alarm, the system will no longer respond to the transmitters and the starter disable output will activate to disable the vehicle from starting.

ACTIVATING SERVICE MODE1. While the ignition is “ON” press and hold the Program Button for five seconds. Thepark lights will flash and the siren will chirp five times to confirm that the system is in Service Mode. 2. While in Service Mode the remote start functions will be disabled and LEDs will be “ON” steady. Door locks and trunk release are still operational.

DEACTIVATING SERVICE MODE1. While the ignition is “ON” press and hold the Program Button for five seconds. The park lights will flash and the siren will chirp two times to confirm that the system has exited Service Mode. 2. All Alarm Functions are reactivated.

System Service Mode

Service Mode- By Remote

SERVICE MODE ACTIVATED1 - Press and release button 4 then hold Button 4 again for 6 seconds or until the status LEDs comes on solid.NOTE: The siren will chirp 5 times as confirmation.

SERVICE MODE DEACTIVATED1 - Press and release button 4 then hold Button 4 again for 6 seconds or until status LEDs turns of.NOTE: The siren will chirp 2 times as confirmation.

Anti Car Jacking Mode

ACTIVATING CAR JACK MODE

DEACTIVATING CAR JACK MODE

Only program this feature if it specifically requested by the customer. Ensure that user is fully trained on the operation of this feature. When car jack mode is activated the system will no longer respond to the remote transmitters. If the starter disable feature was installed the vehicle will not start.

Program Menu 2, Setting 5

- Type 1- Car Jack Mode will activate if the door is opened while the ignition key is in the “On” position. Car Jack Mode may also be activated by pressing the # button on the remote transmitter while the ignition key is in the “On” position.

- Type 2- Car Jack Mode will activate if the ignition key is turned to the “On” position. Car Jack Mode may also be activated by pressing the # button on the remote transmitter while the ignition key is in the “On” position.

1.During the Countdown Mode - Turn the ignition key “ON” then press and release the Program Button one time. 2. After Full Alarm - Turn the ignition key “Off” then “ON” then press and hold the Program Button until the alarm turns off. (About Eight seconds)

Note: If Car Jack Mode goes into full alarm mode, the system will ignore the remote transmitters and this may result in the transmitter needing to be reprogrammed.

PAGE 11


If the alarm system is triggered while armed, the system will retain in memory the cause of the trigger. The diagnostics can then be used to determine what the cause of the trigger was. When disarming the alarm, the siren/horn will chirp 3 times instead of the usual 2 times to indicate the alarm had been triggered.The system’s LED will also flash in pulses to indicate which input triggered the alarm.

NOTE: LED status will be cleared when ignition is turned ON. For proper memory clearing, insure to connect the ignition input to the ignition on the vehicle.

Alarm Diagnostics

Diagnostics Chart

Diagnostics

PAGE 12


Additional LED Flashes

While the system is disarmed and the ignition is in the off position, the LEDs will activate from the following triggers.

1) If the door is opened the LEDs will stay on until the door is closed.2) If the hood is opened the LEDs will stay on until the hood is closed.3) If the shock sensor detects vibration the LEDs will turn on momentarily.4) If the auxiliary sensor input is activated the LEDs will activate momentary.

Siren Chirps on Disarm LED Flashes Diagnostic

Three Chirps Two Flashes Shock Sensor Was ActivatedThree Chirps Three Flashes Door/Hood Pin Input TriggeredThree Chirps Four Flashes Ignition Input Triggered None Off System DisarmedNone On Solid System in Valet/ Service ModeNone Single Flashes Alarm System is ArmedNone Rapid Flashes Passive Arming CountdownOn/Off Rapid Flashes Car Jack Mode Countdown

INSTALL GUIDE - storage.googleapis.com · Recommended Installation Procedures Mounting the Module...

Documents

Transcript of INSTALL GUIDE - storage.googleapis.com · Recommended Installation Procedures Mounting the Module...