INSTALL GUIDE OEM AL RS FM6 ADS ALCA ENcdncontent2.idatalink.com/corporate/Content/Manuals... · 01...
Transcript of INSTALL GUIDE OEM AL RS FM6 ADS ALCA ENcdncontent2.idatalink.com/corporate/Content/Manuals... · 01...
Revision Date20140428
Document numbeR
notice The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be in-stalled by a certified technician. Please review the Installation Guide carefully before beginning any work.
beFoRe instaLLation1- Connect module to computer2- Login to Weblink account3- Flash firmware to module (module is not preloaded with firmware)4- Use accessories accordingly (accessories are sold separately)
instaLL guiDeOEM-AL(RS)-FM6-[ADS-ALCA]-EN
haRDwaReADS-ALCA
accessoRiesADS-USB (REQUIRED)
FiRmwaReOEM-AL(RS)-FM6-[ADS-ALCA]
www.idatalink.comAutomotive Data Solutions Inc. © 2014
14512
vehicLe List - 1 oF 1M
AK
E
MO
DEL
YEA
R
INST
ALL
TYP
E
FEATURES
DAT
A IM
MO
BIL
IZER
BYP
ASS
TAC
HO
MET
ER S
TATU
S
HO
OD
STA
TUS
OU
TPU
T
BR
AK
E P
EDA
L ST
ATU
S O
UTP
UT
RA
P S
HU
TDO
WN
CTR
L
HEA
TED
MIR
RO
RS
CTR
L
HEA
TED
SEA
TS C
TRL
REA
R D
EFR
OST
CTR
L
A/M
RS
CTR
L FR
OM
OEM
REM
OTE
S
FOR
D
Fusion STD key AT 13-14 1 • • • • • • • • •
Fusion Hybrid STD key AT 13-14 1 • • • • • • • • •
Fusion PTS AT 13-14 1 • • • • • • • • •
Fusion Hybrid PTS AT 13-14 1 • • • • • • • • •
LIN
CO
LN MKZ PTS AT 13-14 1 • • • • • • • • •
MKZ Hybrid PTS AT 13-14 1 • • • • • • • • •
NOTES
I This fi rmware does not cover the doorlock feature.Use the OEM remote or an aftermarket one button remote to control the doorlock feature. The OEM remotes remain functional during runtime.
II The maximum runtime for all 2013 models is 20 minutes. The remote start sequence can only be done once. To perform another remote start sequence, start and stop the vehicle or wait 1 hour.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 2 oF 13• 20140428DOC.: #14512
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 3 oF 13• 20140428
BOX CONTENTS - 1 OF 1
23
1
21
3
34
21
76
9
54321
10
845
2
67
1
3
45
2
6
1
3
D
C
B
A
F
E
PROGRAMMINGBUTTON
LED 1
BLACKDATA PORT(WEBLINK, RF, TELEMATIC)
BLUE
WHITE
WHITE
WHITE
BLACK
6 PIN WHITE CONNECTOR
7 PIN WHITE CONNECTOR
MODULE 4 PIN BLACK CONNECTOR
10 PIN BLACK CONNECTOR
DATA CABLE 1
DATA CABLE 2
3 PIN WHITE CONNECTOR
3 PIN BLUE CONNECTOR
BOX CONTENTS
WEBLINK CABLE (required accessory sold separately)
WEBLINK CABLE
COMPUTERUSB PORT
4 PIN BLACK CABLE
MODULEDATA PORT
DOC.: #14512
TYPE 1 - WIRE CHART - 1 OF 1M
AK
E
MO
DEL
YEA
R
WIR
ED
ESC
RIP
TIO
N
CO
NN
ECTO
RN
AM
E
CO
NN
ECTO
RC
OLO
R
CO
NN
ECTO
RTY
PE
PO
SITI
ON
WIR
EC
OLO
R
PO
LAR
ITY
MO
DU
LELO
CATI
ON
CO
MP
ON
ENT
LOCA
TOR
FOR
D
Fusion /Fusion Hybrid STD keyAT
13-14
CanH 1 OBDII Black 24 pin 20 Blue (DATA) OBDII module, driver side dash ~
CanL 1 OBDII Black 24 pin 19 White (DATA) OBDII module, driver side dash ~
CanH 2 OBDII Black 24 pin 23 Gray/Orange (DATA) OBDII module, driver side dash ~
CanL 2 OBDII Black 24 pin 22 Purple/Orange (DATA) OBDII module, driver side dash ~
12V OBDII Black 24 pin 13 White/Red (+) OBDII module, driver side dash ~
Ground OBDII Black 24 pin 01 Black/Gray (-) OBDII module, driver side dash ~
Fusion /Fusion Hybrid PTSAT
13-14
CanH 1 OBDII Black 24 pin 20 Blue (DATA) OBDII module, driver side dash ~
CanL 1 OBDII Black 24 pin 19 White (DATA) OBDII module, driver side dash ~
CanH 2 OBDII Black 24 pin 23 Gray/Orange (DATA) OBDII module, driver side dash ~
CanL 2 OBDII Black 24 pin 22 Purple/Orange (DATA) OBDII module, driver side dash ~
12V OBDII Black 24 pin 13 White/Red (+) OBDII module, driver side dash ~
Ground OBDII Black 24 pin 01 Black/Gray (-) OBDII module, driver side dash ~
LIN
CO
LN MKZ /MKZ Hybrid PTSAT
13-14
CanH 1 OBDII Black 24 pin 20 Blue (DATA) OBDII module, driver side dash ~
CanL 1 OBDII Black 24 pin 19 White (DATA) OBDII module, driver side dash ~
CanH 2 OBDII Black 24 pin 23 Gray/Orange (DATA) OBDII module, driver side dash ~
CanL 2 OBDII Black 24 pin 22 Purple/Orange (DATA) OBDII module, driver side dash ~
12V OBDII Black 24 pin 13 White/Red (+) OBDII module, driver side dash ~
Ground OBDII Black 24 pin 01 Black/Gray (-) OBDII module, driver side dash ~
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 4 oF 13• 20140428DOC.: #14512
A
B
C
D
F
21
34
21
3
21
3
56789
10
21
34567
21
3456
F
A
B
CD E DATA
3456 1217181920
781516
11121314
9102324 2122
E
21
34
21
34
SELECT ONE OF THE TWO OPTIONSSTEP 1
CONNECT TEMPORARILYSEE PROGRAMMING PROCEDURE
STEP 2
STEP 3
OBDII MODULE, DRIVER SIDE DASH
TYPE 1 - WIRING DIAGRAM - 1 OF 1
GRAY/YELLOW (NC)01 GRAY/YELLOW (NC)02 GRAY/RED (NC)
GREEN/YELLOW (NC)03 GREEN/YELLOW (NC)04 GREEN/RED (NC)05 BLUE/YELLOW (NC)06 BLUE/RED (NC)
01 PINK (NC) PINK/BLACK (NC)02 PINK/BLACK (NC)
03 ORANGE (NC)
05 ORANGE/BLACK (NC) BROWN/YELLOW - CANL06 BROWN/YELLOW - CANL
03 WHITE/BLACK (NC)
01 WHITE (NC)
BROWN/RED - CANH07 BROWN/RED - CANH
(NC)04 ORANGE/WHITE (NC)
01 GREEN/BLACK (NC)
03 RED/WHITE (NC)02 BLUE/BLACK (NC)
04 BROWN (NC)
06 PURPLE/BLACK (NC)05 PURPLE/YELLOW (NC)
WHITE 07 WHITE (NC)08 BLACK/WHITE (NC)
10 PURPLE/WHITE (NC)
02 YELLOW/RED (NC)03 YELLOW/BLACK (NC)
01 YELLOW (NC)
CANL 1 - 19
CANL 2 - 22
CANH 1 - 20
CANH 2 - 23
12V (+) - 13GROUND (-) - 01
02 WHITE/RED (NC)
09 GREEN (NC)
MODULE
BLACK
CONNECT TO VEHICLESEE PROGRAMMING PROCEDURE
DATA CABLE
OR
02 WHITE (NC)03 BLACK - GROUND04 RED - 12V (+)
GROUND12V (+)
01 BLUE/WHITE (NC)WITHOUT A COMPATIBLE ACCESSORY:CONNECT 12V AND GROUND FROM MODULE TO VEHICLE.
WITH A COMPATIBLE ACCESSORY:SEE THE COMPATIBLE ACCESSORIES PAGE FOR DETAILS.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 5 oF 13• 20140428DOC.: #14512
01
02
ENGINESTARTSTOP
OFF ACC ON STARTON
03
04
ENGINESTARTSTOP
OFF ACC ON STARTOFF
05
06
07
ENGINESTARTSTOP
OFF ACC ON STARTON
08
09
ENGINESTARTSTOP
OFF ACC ON STARTOFF
10
MODULE PROGRAMMING PROCEDURE - 1 OF 1
CONNECT every wire shown in STEP 1 and STEP 2 of the wiring diagram.
Set ignition to ON position.
Wait, LED 1 will turn solid RED.
Set ignition to OFF position.
Wait, LED 1 will fl ash GREEN rapidly.
DISCONNECT every wire shown in STEP 2 and CONNECT every wire shown in STEP 3 of the wiring diagram.
Set ignition to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Set ignition to OFF position.
Module Programming Procedure completed.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 6 oF 13• 20140428DOC.: #14512
>>
01
02
ENGINESTARTSTOP
OFF ACC ON STARTON
03
04
ENGINESTARTSTOP
OFF ACC ON STARTOFF
05
>>
VALET MODE PROGRAMMING PROCEDURE - 1 OF 1
NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.
Time restriction. Complete next step within 7 seconds.
Cycle ignition ON fi ve times [5x OFF/ON] rapidly.
Wait, LED 1 will turn solid RED for 2 seconds.
Set ignition to OFF position.
Valet Mode Programming Procedure completed.
To exit valet mode: repeat steps 1 to 5.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 7 oF 13• 20140428DOC.: #14512
>>
>>
>>
01
ENGINESTARTSTOP
OFF ACC ON STARTOFF
02
03[X]
04
05[Y]
06
07[Z]
08[Z]
09
10
11[Y]
12
13
14
>>
MODULE NAVIGATION PROCEDURE - 1 OF 1
It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP 13.
Module must be programmed to the vehicle.
Use the Module Navigation Chart on the next page.
Set ignition to OFF position.
TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid GREEN.
IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will fl ash GREEN an equal amount of times continuously.
TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid RED.
IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will fl ash RED an equal amount of times continuously.
TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid GREEN.
LED 1 will flash GREEN as many times as the current (or default) setting number, continuously.
IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will fl ash GREEN an equal amount of times continuously.
To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure.
To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED.
LED 1 will fl ash RED as many times as the current option number continuously.
Configure every other setting and proceed to step 13.
MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED 1 will fl ash RED rapidly. Release programming button. LED 1 will turn OFF.
Module navigation completed.
Failure to exit the Module Navigation will drain vehicle battery.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 8 oF 13• 20140428DOC.: #14512
moDuLe navigation chaRt - 1 OF 1
moDuLe navigation chaRt:notes
[X] m
enu
s
[Y] o
Ptio
ns
[Z] s
etti
ngs
I Default settings are listed in bold.
01 CONFIGURATION
01-04 N/A 01 N/AII Make sure the option is covered on the vehicle before
attempting to change the setting. 05 TAKEOVER01 enabLe02 DISABLE*
06 N/A 01 N/A
07 FACTORY KEYLESS RS SEQUENCE
01 DISABLE02 N/A03 LOCK + UNLOCK + LOCK04 LocK + LocK + LocK
08 MODULE RUN TIME
01 03 MIN02 05 MIN03 10 MIN04 15 MIN05 25 MIN**06 30 MIN**07 35 MIN**08 15 min
09-12 N/A 01 N/A02-07 Technical Support only 01 N/A 01 N/A
*Vehicle will shutdown when a door is opened.**The maximum runtime for 2013 models is 20 minutes.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 9 oF 13• 20140428DOC.: #14512
Remote staRteR eRRoR coDes - 1 OF 1
Remote staRteR eRRoR coDes:notes
[X] n
um
beR
oF
PaR
Kin
g Li
ght
FLas
hes
Dia
gno
stic
I WARNING: The following applies only when the parking lights are connected and supported by the system.
03 Foot brake is ON. 04 Hood is open.
II After a remote starter failure, the parking lights will fl ash [X] number times to indicate an error code. See table.
05 Engine tach signal is lost.06 System is in Valet Mode.07 Vehicle is moving (VSS).08 Glow plug timeout error.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 10 oF 13• 20140428DOC.: #14512
moDuLe Diagnostics - 1 OF 1
test moDuLe
LeD
1 s
tatu
s
Dia
gno
stic
I DURING PROGRAMMING
Flashing RED Missing/wrong information from fi rmware or vehicle.Solid RED Module waiting for more vehicle information.Flashing GREEN Additional steps required to complete module programming.Solid GREEN then OFF Module correctly programmed.OFF No activity or module already programmed.
II DURING REMOTE START
Flashing RED Module incorrectly programmed.Solid RED Module incorrectly programmed.Flashing GREEN Module correctly programmed and operational.Solid GREEN then OFF Reset in progress.OFF Invalid ground when running status from remote starter.
III WITH IGNITION OFF
Flashing RED Module incorrectly programmed or connected.Solid RED Module not programmed. Waiting for more vehicle information.Flashing GREEN False ground when running status from remote starter.Solid GREEN then OFF Reset in progress.OFF Module at rest and ready for a remote start sequence.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 11 oF 13• 20140428DOC.: #14512
01
02
03
04
05
06
07
08
>>
MODULE RESET PROCEDURE - 1 OF 1
Disconnect all connectors from module except the BLACK 4-PIN connector.
Disconnect the BLACK 4-PIN connector.
PRESS AND HOLD programming button while connecting the BLACK 4-PIN connector.
Wait, LED 1 will flash RED. RELEASE programming button.
LED 1 will turn RED for 2 seconds.
Module RESET completed.
Reconnect all connectors.
Repeat programming procedure.
Failure to follow procedure may result with a DTC or a CHECK ENGINE error message.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 12 oF 13• 20140428DOC.: #14512
>>
01
02
ENGINESTARTSTOP
OFF ACC ON STARTON
03
04
>>
TAKEOVER PROCEDURE - 1 OF 1
All vehicle doors must be closed and locked prior to remote start sequence.
Press unlock on OEM or aftermarket remote or request switch.
DO NOT PRESS BRAKE PEDAL. Set ignition to ON position. Wait 2 seconds for key validation.
Press and release BRAKE pedal.
Take over procedure completed.
Failure to follow procedure will result in vehicle engine shutdown.
www.idatalink.comAutomotive Data Solutions Inc. © 2014 OEM-AL(RS)-FM6-[ADS-ALCA]-EN
Page 13 oF 13• 20140428DOC.: #14512