INS LA1A Project2 Layout 1 · service representative at: 905-851-6781 toll free 1-800-461-5901 or...
2
INS LA1A REMOVAL OF FAUCET: Always turn the water supply off before removing the existing faucet or disassembling a valve. Open both faucet handles to relieve water pressure and to ensure that the water has been successfully turned off. CARE OF FAUCET: The use of warm water and a soft cloth is all that is required to clean Rubinet products. The patina of our living finishes (Oil Rubbed Bronze & Tuscan Brass) will change as a result of normal use. Applying Mineral Oil on occasion will create a softer look, subtle color changes and character. TWO HANDLE WIDESPREAD LAVATORY SET MODEL 1ARBLAC or L If you need assistance with installation, replacement parts or have any questions regarding your Rubinet product, please call a Customer service representative at: 905-851-6781 toll free 1-800-461-5901 or visit www.rubinet.com INS LA1A LIFT ROD POP-UP ROD THUMB SCREW SPRING CLIP LOCK NUT ADJUSTMENT SCREW TAIL PIECE Assemble the Lift Rod as shown, Nylon Bearing first then the Rod and finally the Rod Nut. Insert the Pop-Up Rod in the Spout. Push the Lift Rod down to the Open Drain Position. Connect the Pop-Up Rod to the Extension Ladder as shown using the Spring Clip and Thumb Screw to secure both pieces together. Insert the Drain Plug into the sink. With the Pop-Up Rod all the way down the drain should be open. To close it, lift the Pop-Up Rod. The Drain Plug works on gravity and has an adjustment screw. Loosen the Lock Nut to make any adjustment required then re-tighten the Lock Nut to maintain the adjustment. Hook up the ‘P’ Trap to the Drain Tail Piece. Finally, connect the water supply from the Shut-Off valves (not supplied) to the bottom of the Sidebodies. Remove the Aerator from the spout and flush the system to clear any debris that might have accumulated and replace the aerator. 13 14 15 16 17 18 WIDESPREAD LAV SET POP-UP DRAIN ASSEMBLY 1 4
Transcript of INS LA1A Project2 Layout 1 · service representative at: 905-851-6781 toll free 1-800-461-5901 or...
INS LA1A
REMOVAL OF FAUCET:
Always turn the water supply off before removing the existing faucet ordisassembling a valve. Open both faucet handles to relieve waterpressure and to ensure that the water has been successfully turned off.
CARE OF FAUCET:
The use of warm water and a soft cloth is all that is required to cleanRubinet products. The patina of our living finishes (Oil Rubbed Bronze &Tuscan Brass) will change as a result of normal use. Applying Mineral Oilon occasion will create a softer look, subtle color changes and character.
TWO HANDLE WIDESPREAD LAVATORY SET
MODEL 1ARBLAC or LIf you need assistance with installation, replacement parts or have anyquestions regarding your Rubinet product, please call a Customerservice representative at: 905-851-6781 toll free 1-800-461-5901or visit www.rubinet.com
INS LA1A
LIFT RODPOP-UP ROD
THUMB SCREW
SPRING CLIP
LOCK NUT
ADJUSTMENTSCREW
TAIL PIECE
Assemble the Lift Rod as shown,Nylon Bearing first then the Rod andfinally the Rod Nut.
Insert the Pop-Up Rod in the Spout.
Push the Lift Rod down to the OpenDrain Position. Connect the Pop-UpRod to the Extension Ladder asshown using the Spring Clip andThumb Screw to secure both piecestogether.
Insert the Drain Plug into the sink.With the Pop-Up Rod all the waydown the drain should be open. Toclose it, lift the Pop-Up Rod. TheDrain Plug works on gravity and hasan adjustment screw. Loosen theLock Nut to make any adjustmentrequired then re-tighten the Lock Nutto maintain the adjustment.
Hook up the ‘P’ Trap to the Drain TailPiece.
Finally, connect the water supply fromthe Shut-Off valves (not supplied) tothe bottom of the Sidebodies.
Remove the Aerator from the spoutand flush the system to clear anydebris that might have accumulatedand replace the aerator.
13 14
15 16
17 18
WIDESPREAD LAV SET POP-UP DRAIN ASSEMBLY
14
INS LA1AINS LA1A
BRASS NUT
METAL WASHER
RUBBER WASHER
JIG BRASS NUT
SPACER
FLANGE
HANDLE
From the Mounting Kit, assemble one BrassNut, one Metal Washer and one RubberWasher to each Sidebody as shown.
Mount each Sidebody (HOT on the left COLDon the right) from under the sink/deck andassemble another Rubber Washer MetalWasher and Nut, to the top side of eachSidebody.
Next using the Jig provided, adjust thetop side Brass Nut so that the correctsidebody height is achieved.
Tighten the Brass Nut on theunderside of the sink/deck to secureeach sidebody.
Screw both Flanges to theSidebodies.
Install the small Teflon Spacer atopeach flange before attaching theHandles.
Turn each valve off and position eachHandle as required before tighteningthe Set Screw using the Allen Keyprovided.
1 2
3 4
5 6
GASKET
SUPPLY HOSES
THREADED ROD
POP-UP BASKET
RUBBER WASHER
LIFT-ROD HOLE
To the bottom of the Spout assembleboth Supply Hoses (HAND TIGHTENONLY) the Threaded Rod from theSpout Mounting Kit and the Gasket.
Then assemble the Spout in thecentre hole of the sink/deck as shown.
From the underside of the sink/deckassemble the remaining parts of theSpout Mounting Kit to the ThreadedRod. Rubber Washer first then theMetal Washer and finally the TieDown Screw to secure the spout.
Attach each Supply Hose to thecorresponding Sidebody. Do not overtighten.
Insert the Pop-Up Basket and RubberWasher as shown in the sink.Plumbers putty can be used insteadof the Rubber Washer if prefered.
Assemble the remaining Pop-Up partsunder the sink in the order shown,making sure that the Lift-Rod Hole isfacing the back of the sink.
7 8
9 10
11 12
2 3
![Untitled-10 [] · 600-3656-153 Drive Stud 610-8043-059 Screw 8043-001 CO STREAMLINER LOCOMOTIVE 610-8043-213 Side Rod Assembly O 610-8043-917 Screw (Side Rod) 600-8905-036 Washer](https://static.fdocuments.us/doc/165x107/5f2de49150c7ab7bfc5e2f1d/untitled-10-600-3656-153-drive-stud-610-8043-059-screw-8043-001-co-streamliner.jpg)