INNOVATIVE PILING SOLUTIONS - Home | Hi...5 · Side grip pile drivers are the optimum solution for a...
Transcript of INNOVATIVE PILING SOLUTIONS - Home | Hi...5 · Side grip pile drivers are the optimum solution for a...
INNOVATIVE PILING SOLUTIONS
MOVAX PRODUCT CATALOGUE 2017
2
HIGHER PRODUCTIVITY – SIGNIFICANT SAVINGS
EFFICIENT – FAST – FLEXIBLE – ACCURATE - SAFE
WWW.MOVAX.COM
3
INTRODUCTION 5
PILE DRIVERS 7
SG-75V 16
SG-60V 17
SG-50V 18
SG-45V 19
SG-75 20
SG-60 21
SG-50 22
SG-45 23
SG-40 24
SG-30 25
ML-30 26
ML-25 27
ML-15R 28
ML-15 29
PILING HAMMERS 33
DH-15 36
DH-25 37
DH-35 38
DH-45 39
EML-12 40
PILING DRILLS 43
TAD-31S 44
TAD-31L 45
TAD-32 46
TAD-51 47
MANIPULATORS 48
MPM-4000 49
MOVAX CONTROL SYSTEM 51
MCS Lite 52
MCS Pro 54
MCS Pro+auto 56
SERVICES 59
TABLE OF CONTENTS
PILE DRIVERS
PILING HAMMERS
PILING DRILLS
4
SIDE GRIP PILE DRIVERS
PILING HAMMERS PILING DRILLS
5
· Side grip pile drivers are the optimum solution for a wide range of piling requirements and a variety of site and soil conditions - especially when a high-degree of precision is required, and for piling in sensitive environments and when limited space or access is available. The same unit can handle, pitch and drive piles and is capable of accomplishing the whole process without the need of manual handling or assisting machinery.
· Piling hammers are utilised to drive load-bearing piles and to assist in sheet pile driving, even in the most difficult soil conditions. MOVAX piling hammers are the optimum solution to complete a pile installation after reaching refusal with a side grip pile driver or when load testing is required. The piling hammers can be either excavator or excavator leader mast mounted.
· Piling drills are designed for cast in-situ piling and other drilling requirements. MOVAX piling drills are especially suitable for sites with confined spaces and when limited space or headroom is available.
In addition MOVAX develops and manufactures handling equipment for masts, poles and gantries as well as piles.
The excavator-mounted MOVAX piling and handling equipment can be changed fast and flexibly to handle multiple and varying tasks. All MOVAX piling equipment are controlled with the same MOVAX Control System for maximum flexibility and ease-of-operation.
Movax Oy is a Finnish, privately-owned company, established in 1993, which specialises in the design,
development and manufacturing of excavator-mounted piling equipment with automatic steering. Movax
Oy, which is part of the Terra Patris Group, is located in Hämeenlinna, Finland and is represented worldwide
by a network of partners. Movax is the developer of modular side grip technology and has several patents
and its trademark, MOVAX®, is registered all over the world.
INTRODUCTION: THE MOVAX WAY-OF-PILING
MOVAX piling equipment is utilised for a wide range of different work: to construct foundations, to build retaining walls and cofferdams, and when performing trenching and excavation work. MOVAX is, however, not merely piling equipment but most efficient, fast, flexible, accurate and safe way-of-working - the MOVAX-way-of-piling - which results in a higher productivity and thus significant time and cost savings in a wide range of applications and different works.
With more than 1,500 units delivered - to more than 50 countries, on six continents – Movax Oy is a proven supplier of innovative piling solutions.
Movax’s comprehensive range of piling equipment includes PILE DRIVERS, PILING HAMMERS, PILING DRILLS and the state-of-the-art Movax Control System (MCS™):
WWW.MOVAX.COM
6
7
PILE DRIVERS
FEATURES · Suitable for a wide range of applications
· Suitable for different site and soil conditions, including sensitive environments and when a high degree of precision is required or when limited space is available
· Excavator-mounted - available for different excavator models/sizes, for crawler and wheeled excavators, railroaders etc; designed to work on a standard excavator with normal auxiliary hydraulics
· Available in different models & sizes to meet a wide range of piling needs
· Available for a wide range of piles including sheet piles, H-piles, tubular steel piles, timber piles etc.
· Based on the MOVAX Modular System (MMS™) which enables the use of the same unit on multiple different piling work
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Available with M-logbook™ for documentation and reporting (optional, requires MCS Pro or MCS Pro+auto)
MOVAX side grip pile drivers are excavator-mounted, high frequency, vibratory-type pile drivers - available
with fixed or variable eccentric moment - for handling, pitching, driving and extracting different type of
piles in a wide range of site and soil conditions.
FOR HANDLING, PITCHING, DRIVING AND EXTRACTING PILES
8
MOVAX MODULAR SYSTEMMOVAX side grip pile drivers are capable of taking care of the entire piling process from handling, pitching
and driving to exctracting piles without the need of manual handling or assisting machinery and personnel.
Due to the MOVAX Modular System (MMS™) - with interchangeable arms, clamps and pads - the same side
grip pile driver can furthermore be utilised to handle a wide range of different type of piles ranging from
sheet piles, tube piles and H- beams to timber piles.
9
10
11
8
74*
63*
52*
1
1 Sheet clamps
2 H- beam clamps
3 Tube pile clamps
4 Adapters
5 Bottom clamp
ML-MODELS
1 Pads 5 Sheet pile arms 9 4th jaw
2 Tube pile clamps 6 Modular arms 10 Bottom clamp
3 Sheet clamps 7 Tubular pile arms 11 Tandem bottom clamp
4 Timber pile clamps 8 Adapters 12 Pads
SG-MODELS
12
5
4
3
1
2
5
* for modular arms
9
MOVAX MODULAR SYSTEM
ML-modelsMOVAX side grip pile drivers (ML-models) are available with the following standard, interchangeable arm and clamp options. Customised solutions are available upon request. Models ML-25 and ML-30 are equipped with a bottom clamp (available as an option for models ML-15 and ML-15R).
MODULAR ARMSModular arms are utilised for different type of piles and can be equipped with the following type of clamps:
TUBE PILE CLAMPSØ 90 - 457 mm
Ø 60 - 300 mm (ML-15R)
Steel Ø 80 - 300 mm, plastic Ø 100 - 300 mm (ML-15)
TIMBER PILE CLAMPSØ 210 - 325 mm
Ø 100 - 300 mm (ML-15, ML-15R)
H-BEAM CLAMPSmin H180
SHEET PILE CLAMPS d 210
d140 (ML-15, ML-15R)
BOTTOM CLAMPThe bottom clamp is used to handle and drive sheet piles and tubes. Driving caps are available for tube and timber piles.
Sheet pile pads Tube pads
10
MOVAX MODULAR SYSTEM
SG-modelsMOVAX side grip pile drivers (SG-models) are available with the following standard, interchangeable arm, clamp and pad options. Customised arm and clamp solutions are available upon request. All SG-models are equipped with a bottom clamp as a standard.
MODULAR ARMSModular arms are utilised for different types of piles and can be equipped with the following types of clamps:
TUBE PILE CLAMPSØ 90 - 610 mm Ø 90 - 457 mm (SG-30, SG-40)
TIMBER PILE CLAMPSØ 160 - 420 mm
Ø 200 - 420 mm (SG-30, SG-40)
SHEET PILE CLAMPS Sheet pile clamps can be utilized for sheet piles, H-beams and smaller tubes.
Standard pads Tube pads Railway track pads
w 400-1200 mm / d 265 mm H180-H500
min H180 (SG-30, SG-40)
Ø90-250
SHEET PILE ARMSSpecial sheet pile arms are the optimum solution when driving only or mainly sheet piles, smaller tubes or H-beams.
Standard pads Tube pads Railway track pads
w 400-1200 mm / d 265 mm H180-H500
min H180 (SG-30, SG-40)
Ø90-250
TUBULAR PILE ARMSSpecial tubular pile arms are utilised to drive larger tube piles.
Ø 300 - 762 mm Ø 90 - 457 mm (SG-30, SG-40)
11
MOVAX MODULAR SYSTEM
SG-models
BOTTOM CLAMPThe bottom clamp is used to handle and drive sheet piles, tubes and railway tracks. The bottom clamp can be provided with a 4th jaw (optional) for added pile handling capabilities.
Sheet pile pads Tube pads Railway track pads
4TH JAW
TANDEMBOTTOM CLAMPThe tandem bottom clamp is used to handle and drive large tubes, Ø 406.4 – 1220 mm (SG-45 - SG-75).
Tube pads
12
13
SIDE GRIP PILE DRIVERS
VARIABLE ECCENTRIC MOMENT
Ampl
itude
Ampl
itude
Time
Start up Start upShutdown ShutdownFull speed Full speed
STANDARD ECCENTRIC MOMENT
SG-MODELS
VARIABLE ECCENTRIC MOMENT
SG (V)-MODELS
MOVAX side grip pile drivers are available in two different configurations: fixed eccentric moment and variable eccentric moment (V-models).
Disturbances to the surrounding environments can be minimised by operating at high frequencies (typically above 38 Hz) to avoid oscillation at the natural frequencies of the surrounding structures. MOVAX SG-V-models are high frequency (38-50 Hz) resonance-free vibratory pile drivers which allow starting up and shutting down the side grip pile driver without vibration. This is achieved
by shifting the upper row eccentrics with respect to the lower row eccentrics. The total eccentric moment of the side grip pile driver can thus be varied between 0% and 100%; hence variable eccentric moment. The resonance-free start-up and shutdown means that the SG-V-models are the ideal solution when working in urban areas or in sensitive environments. In addition to safer vibration, the SG-V-models also cause less noise and are faster and more comfortable to use.
Standard vibro
MOVAX high frequency, fixed eccentric moment vibro
MOVAX high frequency, variable eccentric moment vibro
Full Speed OperationStart Stop
Ampl
itude
of S
oil V
ibra
tion
(mm
)
14
SG-MODELS
Models SG-45 to SG-75 are modular, variable (V) or fixed eccentric moment side grip pile drivers which can be fitted onto a wide selection of crawler and wheeled excavators as well as railroaders.
The model SG-75 is designed for larger excavators whereas the SG-45 to SG-60 models are the optimum choice for medium sized excavators. The SG-45 to SG-75 models are suitable for a wide variety of applications and work ranging from civil, road and rail to mining, environmental, energy and piers & waterways.
Models SG-30 and SG-40 are suited for the utility sector, especially where work is required to be undertaken by wheeled or small tracked excavators.
ML-MODELS
Models ML-25 and ML-30 are modular, lightweight side grip pile drivers which are easy to operate with wheeled excavators, smaller railroad vehicles, dredgers and even some of the biggest backhoes.
ML-15 is designed for mini- and midi-excavators and especially useful for landscaping projects, working on a barge on waterfront jobs, or in any place with limited access or a sensitive environment.
ML-15R is designed for solar panel foundations and when a high degree of precision in positioning and verticality is important; and for installing raked piles at any required angle.
SIDE GRIP PILE DRIVERS
SELECTION
15
ML-MODELS
Excavator size 13-16 ton 9 - 12 ton 7 - 21 ton 7 - 8 ton
Pile size (length / weight)
6 m / 900 kg
8 m / 400 kg
10 m / 400 kg
ML-30 ML-25
4 m / 500 kg
6 m / 300 kgML-15R
4 m / 400 kg
6 m / 200 kgML-15
Suitable piles
Sheet piles depth 210 mm max depth 140 mm
H-beams min H180 NA
Timber piles Ø 210–325 mm Ø 100–300 mm
Tube piles Ø 90–457 mm Ø60–300 mmØ 80-300 mm (steel)
Ø 100-300 mm (plastic)
SG-MODELS
Excavator size 33 - 40 ton 28 - 32 ton 23 - 28 ton 20 - 24 ton 17 - 21 ton 13 - 16 ton
Pile size (length / weight)
6 m / 2 800 kg
12 m / 1 900 kg
16 m / 1 300 kg
SG-75
SG-75V
8 m / 2 300 kg
12 m / 1 800 kg
16 m / 1 200 kg
SG-60
SG-60V
SG-50
SG-50V
SG-45
SG-45V
6 m / 1 200 kg
8 m / 1 000 kg
10 m / 900 kg
SG-40 SG-30
Suitable piles
Sheet pileswidth 400–1200 mm
depth 265 mm
width 400–1200 mm
depth 260 mm
H-beams H180–H500 min H180
Timber piles Ø 160–420 mm Ø 200–420 mm
Tube piles Ø 90–762mm
Ø 406.4 – 1220 mm with tandem bottom clampØ 90–457 mm
NOTE! Preliminary selection. When making the final selection excavator engine size and hydraulic system design
(oil pump arrangement, oil flow rate/pressure etc) as well as soil and site conditions shall be taken into account.
SIDE GRIP PILE DRIVERS
SELECTION CHART
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with variable eccentric moment. Disturbances of the surrounding environment is minimised by operating at a high frequency and thus avoiding an oscillation of the soil and the surrounding structures at their natural frequencies.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 3450-3708
Height mm 2560
Depth mm 1115
Width mm 1270
Excavator class t 33-40
Engine power, min kW 184
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 7,6
Centrifugal force, max kN 750
Ground vibration low
Resonance-free start/stop yes
Driving method vibration
Swing/tilt angle º 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
6 m x 2 800 kg
12 m x 1 900 kg
16 m x 1 300 kg
SIDE GRIP PILE DRIVERS
SG-75VFEATURES
16
SIDE GRIP PILE DRIVERS
SG-60VFEATURES
17
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with variable eccentric moment. Disturbances of the surrounding environment is minimised by operating at a high frequency and thus avoiding an oscillation of the soil and the surrounding structures at their natural frequencies.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 2560-2791
Height mm 2478
Depth mm 1180 - 1436
Width mm 1193
Excavator class t 28-32
Engine power, min kW 134
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 6,1
Centrifugal force, max kN 600
Ground vibration low
Resonance-free start/stop yes
Driving method vibration
Swing/tilt angle º 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
8 m x 2 300 kg
12 m x 1 600 kg
16 m x 1 200 kg
SIDE GRIP PILE DRIVERS
SG-50VFEATURES
18
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with variable eccentric moment. Disturbances of the surrounding environment is minimised by operating at a high frequency and thus avoiding an oscillation of the soil and the surrounding structures at their natural frequencies.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 2427-2658
Height mm 2478
Depth mm 1180 - 1436
Width mm 1193
Excavator class t 23 - 28
Engine power, min kW 125
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 5,1
Centrifugal force, max kN 500
Ground vibration low
Resonance-free start/stop yes
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
8 m x 2 300 kg
12 m x 1 600 kg
16 m x 1 200 kg
SIDE GRIP PILE DRIVERS
SG-45VFEATURES
19
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with variable eccentric moment. Disturbances of the surrounding environment is minimised by operating at a high frequency and thus avoiding an oscillation of the soil and the surrounding structures at their natural frequencies.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kgm 2422-2653
Height mm 2478
Depth mm 1180 - 1436
Width mm 1193
Excavator class t 20 - 24
Engine power, min kW 100
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 4,6
Centrifugal force, max kN 450
Ground vibration low
Resonance-free start/stop yes
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
8 m x 2 300 kg
12 m x 1 600 kg
16 m x 1 200 kg
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 3330-3588
Height mm 2560
Depth mm 1115
Width mm 1270
Excavator class t 33-40
Engine power, min kW 184
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 7,6
Centrifugal force, max kN 750
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle º 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
6 m x 2 800 kg
12 m x 1 900 kg
16 m x 1 300 kg
SIDE GRIP PILE DRIVERS
SG-75FEATURES
20
SIDE GRIP PILE DRIVERS
SG-60FEATURES
21
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 2460-2691
Height mm 2478
Depth mm 1180 - 1436
Width mm 1193
Excavator class t 28-32
Engine power, min kW 134
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 6,1
Centrifugal force, max kN 600
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
8 m x 2 300 kg
12 m x 1 600 kg
16 m x 1 200 kg
SIDE GRIP PILE DRIVERS
SG-50FEATURES
22
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 2327-2558
Height mm 2478
Depth mm 1180 - 1436
Width mm 1193
Excavator class t 23 - 28
Engine power, min kW 125
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 5,1
Centrifugal force, max kN 500
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
8 m x 2 300 kg
12 m x 1 600 kg
16 m x 1 200 kg
SIDE GRIP PILE DRIVERS
SG-45FEATURES
23
· Designed to match the capabilities of larger excavators and to combine a robust structure with excellent pile handling characteristics.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAXModular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 2322-2553
Height mm 2478
Depth mm 1180 - 1436
Width mm 1193
Excavator class t 20 - 24
Engine power, min kW 100
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300-3000
Eccentric moment kgm 4,6
Centrifugal force, max kN 450
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 265 mm
H-beams size H180-H500
Timber piles size Ø 160 - 420 mm
Tubular piles, tubes size up to Ø 762 mm
LENGTH & WEIGHT
8 m x 2 300 kg
12 m x 1 600 kg
16 m x 1 200 kg
SIDE GRIP PILE DRIVERS
SG-40FEATURES
24
· Designed for the utility sector; especially when work is required to be undertaken by wheeled or small tracked excavators.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 1814
Height mm 2021
Depth mm 1187
Width mm 1193
Excavator class t 17-21
Engine power, min kW 86
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300 - 3000
Eccentric moment kgm 4,1
Centrifugal force, max kN 400
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 280 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 260 mm
H-beams size min H180
Timber piles size Ø 200 - 420 mm
Tubular piles, tubes size Ø 90 - 457 mm
LENGTH & WEIGHT
6 m x 1 200 kg
8 m x 1 000 kg
10 m x 900 kg
SIDE GRIP PILE DRIVERS
SG-30FEATURES
25
· Designed for the utility sector; especially when work is required to be undertaken by wheeled or small tracked excavators.
· Fitted with heavy-duty arms/clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the standard arm/clamp systems and the bottom clamp. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 1790
Height mm 2021
Depth mm 1187
Width mm 1193
Excavator class t 13-16
Engine power, min kW 65
Return pressure, max bar 5
Pressure setting bar 350
Frequency 1/min 2300 - 3000
Eccentric moment kgm 3,1
Centrifugal force, max kN 300
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 280 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400-1200 mm
depth 260 mm
H-beams size min H180
Timber piles size Ø 200 - 420 mm
Tubular piles, tubes size Ø 90 - 457 mm
LENGTH & WEIGHT
6 m x 1 200 kg
8 m x 1 000 kg
10 m x 900 kg
SIDE-GRIP PILE DRIVERS
ML-30FEATURES
26
· Light weight pile driver designed for wheeled excavators, smaller rail road vehicles, dredgers and the biggest backhoes.
· Fitted with heavy-duty clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the clamp systems; bottom clamp optional. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 1205
Height mm 1962
Depth mm 902
Width mm 999
Excavator class t 13-16
Engine power, min kW 65
Return pressure, max bar 5
Pressure setting bar 300
Frequency 1/min 2300 - 3000
Eccentric moment kgm 3,1
Centrifugal force, max kN 300
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400 - 1200 mm
depth 210 mm
H-beams size min H180
Timber piles size Ø 210 - 325 mm
Tubular piles, tubes size Ø 90 - 457 mm
LENGTH & WEIGHT
6 m x 900 kg
8 m x 400 kg
10 m x 400 kg
SIDE-GRIP PILE DRIVERS
ML-25FEATURES
27
· Light weight pile driver designed for wheeled excavators, smaller rail road vehicles, dredgers and the biggest backhoes.
· Fitted with heavy-duty clamps capable of driving a wide range of piles including sheet piles, H-piles, tubular steel piles and other pile sections.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the clamp systems; bottom clamp optional. Customised arms and clamps are available upon special request.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter) kg 1200
Height mm 1962
Depth mm 902
Width mm 999
Excavator class t 9-12
Engine power, min kW 46
Return pressure, max bar 5
Pressure setting bar 220 - 350
Frequency 1/min 2300 - 3000
Eccentric moment kgm 2,6
Centrifugal force, max kN 250
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400 - 1200 mm
depth 210 mm
H-beams size min H180
Timber piles size Ø 210 - 325 mm
Tubular piles, tubes size Ø 90 - 457 mm
LENGTH & WEIGHT
6 m x 900 kg
8 m x 400 kg
10 m x 400 kg
SIDE-GRIP PILE DRIVERS
ML-15RFEATURES
28
· Leader guided pile driver designed especially for laying foundations for solar panels and other applications where a high degree of precision in positioning and verticality is required.
· Fitted with durable clamps capable of driving smaller diameter piles including sheet piles, H-piles, tubular steel piles and other pile sections; also suitable for installing raked piles at any required angle and for driving light piles (with side grip clamping close to the ground buckling of the otherwise flexible pile is avoided).
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the clamp systems; bottom clamp optional. Customised arms and clamps are available upon special request.
· Operated with the MOVAX Control System Lite (MCS Lite) which allows the operator to control all MOVAX operations and commands the auxiliary hydraulics of the excavator.
TECHNICAL DATA
Weight (excl. adapter) kg 1050
Height mm 3505
Depth mm 1480
Width mm 1125
Excavator class t 7-21
Engine power, min kW 39
Return pressure, max bar 5
Pressure setting bar 200
Frequency 1/min 2300 - 3000
Eccentric moment kgm 1,6
Centrifugal force, max kN 150
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Tilt angle o ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400 - 1200 mm
depth 140 mm
H-beams size NA
Timber piles Ø 100 - 300 mm
Tubular piles, tubes Ø 60 - 300 mm
LENGTH & WEIGHT
4 m x 500 kg
6 m x 300 kg
SIDE-GRIP PILE DRIVERS
ML-15FEATURES
29
· Matching in scale for mini- and mid-sized excavators. The unit features bolt-on, changable clamps that are available for a wide variety of different pile and sheet sections including plastic and composite sheets, micro-piles and timber piles. Especially suitable for landscaping projects, working on a barge on waterfront jobs or in any place with limited access or in a sensitive environment.
· High frequency pile driver with fixed eccentric moment.
· Based on the MOVAX Modular System (MMS™). The unit is always equipped with one of the clamp systems; bottom clamp optional. Customised arms and clamps are available upon special request.
· Operated with the MOVAX Control System Lite (MCS Lite) which allows the operator to control all MOVAX operations and commands the auxiliary hydraulics of the excavator.
TECHNICAL DATA
Weight (excl. adapter) kg 649
Height mm 1505
Depth mm 930
Width mm 792
Excavator class t 7-8
Engine power, min kW 39
Return pressure, max bar 5
Pressure setting bar 200
Frequency 1/min 2300 - 3000
Eccentric moment kgm 1,6
Centrifugal force, max kN 150
Ground vibration normal
Resonance-free start/stop no
Driving method vibration
Swing/tilt angle o 360 / ± 30
SUITABLE PILES
TYPES AND DIMENSIONS
Sheet piles width 400 -1200 mm
depth 140 mm
H-beams size NA
Timber piles Ø 100 - 300 mm
Tubular piles, tubes Ø 80 - 300 (steel) mm
Ø 100 - 300 (plastic) mm
LENGTH & WEIGHT
4 m x 400 kg
6 m x 200 kg
30
SIDE GRIP PILE DRIVERS
PILE HANDLING AND DRIVINGMOVAX side grip pile drivers are capable of handling, pitching, driving and extracting a wide range of
different piles without manual handling or the need of assisting machinery or personnel.
31
32
33
PILING HAMMERSMOVAX Piling Hammers are excavator-mounted, hydraulic impact-type hammers for driving load-bearing
piles or assisting in sheet pile driving in even the most difficult soil conditions. MOVAX piling hammers can
be utilised to complete a pile installation after reaching refusal with a Side Grip pile driver or when load
testing is required.
FEATURES · Suitable for different site and soil conditions
· Suitable for a wide range of piles including sheet piles, H-beams, tubular steel piles, timber piles, concrete piles etc.
· Excavator mounted or excavator leader mast mounted; designed to work on a standard excavator with normal auxiliary hydraulics
· Tilt +/- 15 º
· Available with rotation device +/- 60 º
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Available with M-logbook™ for documentation and reporting (optional, requires MCS Pro or MCS Pro+Auto)
FOR DRIVING LOAD BEARING PILES AND ASSISTING IN SHEET PILE DRIVING
34
PILING HAMMERS
SELECTIONThe MOVAX piling hammer is selected based on the size and type of piles to be driven. The piling hammer is
suitable for all kinds of piles ranging from sheet piles to tubular steel piles and precast concrete piles. A pile
cap is provided for the type of pile in question. The piling hammer product range includes models suitable
for excavators ranging from 20 tons up to 45 tons. Depending on the reach of the excavator the maximum
pile length is approximately 6-7 meters when installed directly onto the excavator stick.
The DH-hammer can be furthermore installed with a leader mast mounted onto the excavator boom. This
will allow for piles up to 12 meter in length to be driven.
35
PILE CAPSDH-hammers can be equipped with the following standard type of pile caps (customised pile caps are availble upon request):
SHEET AND H-PILE
CAP Standard drive plate Ø 550 mm
TUBE PILE CAPDH-15, DH-25 273-508mm DH-35, DH-45 273-508mm
TUBE PILE CAPDH-15, DH-25 559-762 mm DH-35, DH-45 559-762 mm
TUBE PILE CAP DH-15, DH-25 90 - 220 mm DH-35, DH-45 90 - 357 mm
DH-MODELS
Excavator mounted (mounted to the stick)
Excavator size 20 - 30 ton 25 - 45 ton 33 - 45 ton 35 - 50 ton
Pile size (length / weight)
max pile lenght based on excavator reach and stability
DH-15 DH-25 DH-35 DH-45
Suitable piles
Sheet piles width 400–1200 mm, depth 265 mm
H-beams H180–H500
Precast concrete piles 250 mm x 250 mm 250 mm x 250 mm 300 mm x 300 mm 300 mm x 300 mm
Tiber piles Ø 160-420 mm
Tube piles Ø 90-457 mm Ø 90-762 mm Ø 90-762 mm Ø 90-762 mm
NOTE! Preliminary selection. When making the final selection the required bearing load capacity and pile lenght/weight shall be taken into
account. Local laws, rules and regulations must be taken into account when selecting the piling hammer for a specific excavator.
PILING HAMMERS
SELECTION CHART
Excavator leader-mounted (mounted to the boom)
Excavator size 20 - 30 ton 25 - 45 ton 33- 50 ton
Pile size (length / weight)
max pile lenght 12 meters DH-15 DH-25 DH-35
Suitable piles
Sheet piles width 400–1200 mm, depth 265 mm
H-beams H180–H500
Precast concrete piles 250 mm x 250 mm 300 mm x 300 mm 300 mm x 300 mm
Tiber piles Ø 160-420 mm
Tube piles Ø 90-762 mm
NOTE! Preliminary selection. When making the final selection the required bearing load capacity and pile lenght/weight shall be taken into
account. Local laws, rules and regulations must be taken into account when selecting the piling hammer for a specific excavator.
PILING HAMMERS
DH-15FEATURES
36
· Excavator-mounted, hydraulic, impact-type piling hammer.
· Utilised to drive load-bearing tubular steel piles, H-piles and timber piles or assisting in sheet pile driving even in the most difficult soil conditions. Also used in conjunction with side grip pile drivers to complete a pile installation after reaching refusal or when load testing is required.
· The excavator mounting incorporates a 1.3 m leader. The piling hammer can also be mounted on an excavator-mounted leader mast.
· Standard mounting with pin adapter (tilt +/-15º, no rotation). Available with bolt-on-plate mounted rotation device (tilt +/-15º, rotation +/- 60º).
· Available with drive caps for a range of different pile sections.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Total weight (excl. adapter) kg 3460
Ram weight kg 1360
Blows per minute 1/min 0-100
Impact energy kNm 0-15
Drop height m 0-1,2
Pressure relief set max bar 350
Operating pressure bar 150
Oil flow rate l/min 120
Tilt angle º +/- 15
Rotation angle º +/- 60
Total height mm 3850
Frame width mm 500
Transport width mm 1200
Transport depth mm 1870
Excavator class t 20-30
PILING HAMMERS
DH-25FEATURES
· Excavator-mounted, hydraulic, impact-type piling hammer.
· Utilised to drive load-bearing tubular steel piles, H-piles and timber piles or assisting in sheet pile driving even in the most difficult soil conditions. Also used in conjunction with side grip pile drivers to complete a pile installation after reaching refusal or when load testing is required.
· The excavator mounting incorporates a 1.3 m leader. The piling hammer can also be mounted on an excavator-mounted leader mast.
· Standard mounting with pin adapter (tilt +/-15º, no rotation). Available with bolt-on-plate mounted rotation device (tilt +/-15º, rotation +/- 60º).
· Available with drive caps for a range of different pile sections.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Total weight (excl. adapter) kg 4260
Total weight w/ rotation device (excl adapter)
kg 4600
Ram weight kg 2060
Blows per minute 1/min 0-100
Impact energy kNm 0-25
Drop height m 0-1,2
Pressure relief set max bar 350
Operating pressure bar 200
Oil flow rate l/min 120
Tilt angle º +/- 15
Rotation angle º +/- 60
Total height mm 4460
Frame width mm 500
Transport width mm 1200
Transport depth mm 1870
Excavator class t 25-45
37
PILING HAMMERS
DH-35FEATURES
· Excavator-mounted, hydraulic, impact-type piling hammer.
· Utilised to drive load-bearing tubular steel piles, H-piles and timber piles or assisting in sheet pile driving even in the most difficult soil conditions. Also used in conjunction with side grip pile drivers to complete a pile installation after reaching refusal or when load testing is required.
· The excavator mounting incorporates a 1.3 m leader. The piling hammer can also be mounted on an excavator-mounted leader mast.
· Standard mounting with pin adapter (tilt +/-15º, no rotation). Available with bolt-on-plate mounted rotation device (tilt +/-15º, rotation +/- 60º).
· Available with drive caps for a range of different pile sections.
· Operated with the Movax Control System (MCS™) which allows the operator to control all MOVAX operations and commands the auxiliary hydraulics of the excavator and provides information related to for instance the ram energy. The MCS is available in three versions: MCS Lite, MCS Pro or MCS Pro+Auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Total weight (excl. adapter) kg 5390
Ram weight kg 3000
Blows per minute 1/min 0-100
Impact energy kNm 0-35
Drop height m 0-1,2
Pressure relief set max bar 350
Operating pressure bar 250
Oil flow rate l/min 120
Tilt angle º +/- 15
Rotation angle º +/- 60
Total height mm 4460
Frame width mm 650
Transport width mm 1200
Transport depth mm 1870
Excavator class t 33-40
38
PILING HAMMERS
DH-45FEATURES
· Excavator-mounted, hydraulic, impact-type piling hammer.
· Utilised to drive load-bearing tubular steel piles, H-piles and timber piles or assisting in sheet pile driving even in the most difficult soil conditions. Also used in conjunction with side grip pile drivers to complete a pile installation after reaching refusal or when load testing is required.
· The excavator mounting incorporates a 1.3 m leader. The piling hammer can also be mounted on an excavator-mounted leader mast.
· Standard mounting with pin adapter (tilt +/-15º, no rotation). Available with bolt-on-plate mounted rotation device (tilt +/-15º, rotation +/- 60º).
· Available with drive caps for a range of different pile sections.
· Operated with the Movax Control System (MCS™) which allows the operator to control all MOVAX operations and commands the auxiliary hydraulics of the excavator and provides information related to for instance the ram energy. The MCS is available in three versions: MCS Lite, MCS Pro or MCS Pro+Auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Total weight (excl. adapter) kg 6500
Ram weight kg 4000
Blows per minute 1/min 0-100
Impact energy kNm 0-45
Drop height m 0-1,2
Pressure relief set max bar 350
Operating pressure bar 250
Oil flow rate l/min 120
Tilt angle º +/- 15
Rotation angle º +/- 60
Total height mm 4930
Frame width mm 650
Transport width mm 1200
Transport depth mm 1870
Excavator class t 35-50
39
PILING HAMMERS
EXCAVATOR MOUNTED LEADER
FEATURES
40
· Leader Mast for piling applications with over 12 metres of effective leader length.
· Excavator boom mounted; designed to work on a standard excavator with normal auxiliary hydraulics.
· Mounted onto crawler type excavators. All mast-related hydraulics, and winches are integrated to the leader mast itself.
· Bi-directional rope system which enables stepless control of both the speed and the force of the MOVAX Piling equipment in both directions of movement.
· Equipped with a fully integrated service winch for handling of piles and equipment.
· The mast can easily, fast and flexibly be attached and detached thus enabling other usage of the excavator. The mast can also be folded and thus easily transported between sites.
· Operated with the MoOVAX Control System (MCS ProL) which allows the operator to control all MOVAX leader and MOVAX piling equipment operations by commanding the auxiliary hydraulics of the excavator.
TECHNICAL DATA
Weight kg 6800
Height mm 15800
Depth (with excavator bracket)
mm 1500
Width (with hose hanger) mm 1890
Excavator class t 33-40
Travel, max. m 12,3
Side tilt, right/left ±3,5
Rotation, right/left ±28
Main winch
- capacity, lifting t 12
- capacity, pulling t 6
- speed m/min 0-65
Auxiliary/service winch
- capacity t 3
- speed m/min 0-40
Note! The mast can be folded for easier transportation.
41
42
43
PILING DRILLSMOVAX Piling drills are excavator-mounted, auger drive attachments for cast in-situ (concrete) piling and
other drilling work.
FEATURES · Suitable for different site conditions, also for sites with limited
headroom
· Hydraulically operated telescopic kelly bar with two extendable sections or a single, longer extension
· Excavator mounted; designed to work on a standard excavator with normal auxiliary hydraulics
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto
· Availble with M-logbook™ for documentation and reporting (optional, requires MCS Pro or MCS Pro+Auto)
FOR CAST-IN SITU PILING AND OTHER DRILLING WORK
PILING DRILLS
TAD-31SFEATURES
44
· Excavator-mounted auger drive attachments for cast in-situ piling and other earth drilling work. Especially suitable for work in confined spaces while still being good at reaching over obstacles. The telescopic design keeps the machine low and allows working on sites with limited headroom without compromising on drilling depth.
· Hydraulically operated telescopic kelly bar with one longer extension.
· Available with different type of augers for normal soil conditions, hard clay, hard soil etc.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
TAD-31S
Weight (excl. adapter and auger)
kg 3400
Height without auger mm 3830
Depth of piling drill mm 1893
Width of piling drill mm 1365
Excavator class t 24-35
Oil flow rate l/min 75-250
Max return pressure bar 5
Drilling depth m 6,5
Hole diameter* mm 400-1200
Drill speed range rpm 11-74
Side tilt angle ° ±30
Torque Nm 30000
Auger pressing force N 15000
Auger pulling force N 60000
* depending on soil conditions and tooling
45
PILING DRILLS
TAD-31LFEATURES
· Excavator-mounted auger drive attachments for cast in-situ piling and other earth drilling work. Especially suitable for work in confined spaces while still being good at reaching over obstacles. The telescopic design keeps the machine low and allows working on sites with limited headroom without compromising on drilling depth.
· Hydraulically operated telescopic kelly bar with one longer extension.
· Available with different type of augers for normal soil conditions, hard clay, hard soil etc.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
TAD-31L
Weight (excl. adapter and auger)
kg 3500
Height without auger mm 5355
Depth of piling drill mm 1893
Width of piling drill mm 1013
Excavator class t 24-35
Oil flow rate l/min 75-250
Max return pressure bar 5
Drilling depth m 9
Hole diameter* mm 400-1200
Drill speed range rpm 11-74
Side tilt angle ° ±30
Torque Nm 30000
Auger pressing force N 15000
Auger pulling force N 60000
* depending on soil conditions and tooling
46
PILING DRILLS
TAD-32FEATURES
· Excavator-mounted auger drive attachments for cast in-situ piling and other earth drilling work. Especially suitable for work in confined spaces while still being good at reaching over obstacles. The telescopic design keeps the machine low and allows working on sites with limited headroom without compromising on drilling depth.
· Hydraulically operated telescopic kelly bar with two extension.
· Available with different type of augers for normal soil conditions, hard clay, hard soil etc.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter and auger)
kg 3200
Height without auger mm 3855
Depth of piling drill mm 1673
Width of piling drill mm 1013
Excavator class t 24-35
Oil flow rate l/min 75-250
Max return pressure bar 5
Drilling depth m 9
Hole diameter* mm 400-1000
Drill speed range rpm 11-74
Side tilt angle ° ±30
Torque Nm 30000
Auger pressing force N 15000
Auger pulling force N 30000
* depending on soil conditions and tooling
47
PILING DRILLS
TAD-51FEATURES
· Excavator-mounted auger drive attachments for cast in-situ piling and other earth drilling work. Especially suitable for work in confined spaces while still being good at reaching over obstacles. The telescopic design keeps the machine low and allows working on sites with limited headroom without compromising on drilling depth.
· Hydraulically operated telescopic kelly bar with two extension.
· Available with different type of augers for normal soil conditions, hard clay, hard soil etc.
· Controlled with the MOVAX Control System (MCS™); MCS Lite, MCS Pro or MCS Pro+auto.
· Reporting and documentation of piling works with M-logbook™ (optional, requires MCS Pro or MCS Pro+Auto).
TECHNICAL DATA
Weight (excl. adapter and auger)
kg 3200
Height without auger mm 3855
Depth of piling drill mm 1673
Width of piling drill mm 1013
Excavator class t 24-35
Oil flow rate l/min 75-250
Max return pressure bar 5
Drilling depth m 6
Hole diameter* mm 400-1200
Drill speed range rpm 11-74
Side tilt angle ° ±30
Torque Nm 50000
Auger pressing force N 15000
Auger pulling force N 60000
* depending on soil conditions and tooling
4848
MANIPULATORSMOVAX manipulators are designed for fast, flexible and efficient handling of different kinds of masts,
gantries, and poles as well as a wide range of piles. Based on the patented side grip technology, the MOVAX
manipulator is designed for superior maneuverability, safety and accuracy. The manipulator is capable of
handling different type of profiles ranging from double-U-, U-, H-, and I- to rectangular- and tubular-shapes
as well as sheet piles, tubular piles, timber piles and precast concrete piles. Soft gripping surfaces prevent
efficiently damaging sensitive masts, gantries or poles.
The MOVAX Manipulator is controlled by the MOVAX Control System for fast, precise and easy operation
with the utmost safety.
FOR HANDLING PILES
FEATURES · Suitable for a wide range of different type of profiles
· Available for masts, poles gantries and different type of piles
· Available with gripping surfaces tailor-made for the profile to be handled
· Controlled with the MOVAX Control System (MCS™); MCS Lite or MCS Pro
49
MOVAX MANIPULATOR
MPM-4000FEATURES
· 360 degree continuous rotary gear for unlimited and precise handling and positioning
· Adapter plates available to suit most brands of quick hitches or pin-connection
· Fast connection to base machine with one cable and two hose
· Clamping inserts available with soft gripping surfaces to prevent damage on galvanized pole
· Controlled with the MOVAX Control System (MCS™); MCS Lite or MCS Pro.
- Easy & exact pile positioning with integrated inclination sensor and MCS display
- Smooth movements with thumb wheel operated proportional control valves
- Clamping pressure shown on screen
- Integrated safety lock valves on cylinders
- Safety switch for clamp opening
- Adjustable gripping force to prevent damage of for instance galvanized poles or other sensitive profiles
TECHNICAL DATA
Weight (excl. adapter) kg 1950
Height mm 1580
Depth mm 2050
Width mm 960
Excavator or Rail Road Vehicle class t 18 – 35
Rotation angle o +/-60
Tilting angle o 360
Tilting torque Nm 20000
Relief valve pressure max bar 350
Minimum pressure required bar 180
Required oil flow l/min 85
Maximum working load kg 4000
SUITABLE PROFILES
TYPES AND DIMENSIONS
Square sections and H-beams
size from 120x120 up to 650x650
Tubular sections size 100 - 630 mm
Sheet piles size max depth 265 mm
Timber poles and piles 160 - 420 mm
50
51
MOVAX CONTROL SYSTEM
The MOVAX Control System is available in three versions: MCS Lite, MCS Pro and MCS Pro+auto. MCS Lite is a basic control system including all the necessary controls to operate MOVAX piling and handling equipment. MCS Pro includes additional sensors providing added information and intelligence concerning the piling process and the MOVAX equipment. MCS Pro+auto is additionally provided with an auto control function.
FEATURES · Ergonomic and informative user interface
· Colour display
· All functions effortlessly controlled using switches and thumbwheels on the control grips
· Compatible with all MOVAX piling, drilling and handling equipment
· M-logbook™ for reporting and documentation of piling works (optional, requires MCS Pro or MCS Pro+Auto)
· MOVAX Remote™ for remote access, performance monitoring and trouble shooting (optional).
The MOVAX Control System (MCS™) links the excavator with MOVAX’s pile drivers, piling hammers and piling
drills – and leader masts. The system controls the auxiliary hydraulics of the excavator and all the functions
of MOVAX’s piling and drilling equipment. The system utilises inclination and pressure sensors to monitor
for instance the pile driving process – thus assisting the operator to achieve better efficiency, increased
productivity and higher accuracy.
FOR ALL MOVAX PILING EQUIPMENT
MOVAX CONTROL SYSTEM
MCS Lite
52
MCS Lite has a cab-mounted electronic control module with a 3.2″ display. The module is capable of controlling the excavator’s auxiliary hydraulics with a proportional pilot valve for the required hydraulic power for the MOVAX equipment.
The display provides the operator with information about MOVAX: angles, vibro frequency or piling hammer impact energy rate and hydraulic pressure. Basic service interval and system diagnostic data are also available to the operator.
The system is delivered with ergonomic control grips with rollers and switches that allow complete operation with a single grip. The control grips include extra switches and rollers for accommodating functions from the excavator’s original handles.
The MOVAX Control System MCS Lite is a basic control system that gives the operator control over all the
hydraulic functions on the MOVAX piling equipment. The excavator side of the system is simplified, making
it suitable for shorter-term use and for a second excavator that is used occasionally for pile driving. MCS Lite
is compatible with MOVAX piling equipment fitted for the MCS Pro or MCS Pro+auto.
53
MOVAX CONTROL SYSTEM
MCS Lite
1. MOVAX module 2. Valve Block / 3. Grips / 4. Display
1
3
2
4
MCS Lite is compatible with all SG-, DH-, TAD- and MPM-models as well as MOVAX piling equipment with AutoC system.
Note! The MOVAX module is provided with the MOVAX piling equipment.
FEATURES Lite Pro Pro+auto
Colour display 3.2” 7” 7”
Ergonomic control grips with thumb wheels x x x
Proportional control for excavators ALIX hydraulics x x x
Frequency I RPM (SG vibro) x x x
Impact energy rate (piling hammer) x x x
Movax angle (bucket cylinder operated) x x x
Movax angle (side tilt) x x x
Distance and height position NA x x
Auto Control NA optional x
Clamping force adjustment from cab NA x x
System diagnostics NA x x
MOVAX remoteTM optional optional optional
M-logbook NA optional optional
Camera Input NA optional optional
Wireless site camera on tripod NA optional optional
Software update via USB memory stick NA optional optional
54
The MOVAX Control System MCS Pro is an advanced, state-of-the-art control system for easier, precise and
more productive and efficient operation.
MOVAX CONTROL SYSTEM
MCS Pro
The visual user interface of the MCS Pro is based on a 7″ display with easy-to-read graphical symbols for the position, vibro frequency or piling hammer impact energy rate, and hydraulic pressure. User-friendly menus for calibrating and optimising the performance of both the Movax equipment and the excavator hydraulics. The MCS Pro provides full system diagnostics directly on the screen and can be set to remind the operator of critical maintenance tasks, such as changing oil and oil filter.
The control grips with proportional rollers are ergonomically shaped and designed for simultaneous control of multiple operations. The grips have a large number of switches and rollers to accommodate non-MOVAX functions as well.
MCS Pro can be upgraded to meet different needs. Versatile connectivity makes it possible to add pressure sensors, a boom-mounted camera or a wireless site camera for top-level safety, productivity and accuracy. MCS Pro can also be equipped with M-LogbookTM, a documenting and reporting tool for added information about the piling process.
1. MOVAX module 2. Stick boom sensor / 3. Main boom sensor / 4. Excavator module / 5. Valve Block / 6. Grips / 7. Display
8. Camera (optional)
1
2 3
4
5
6
7
8
55
MOVAX CONTROL SYSTEM
MCS Pro
MCS Lite is compatible with all SG-, DH-, TAD- and MPM-models as well as MOVAX piling equipment with AutoC system.
Note! The MOVAX module is provided with the MOVAX piling equipment.
FEATURES Lite Pro Pro+auto
Colour display 3.2” 7” 7”
Ergonomic control grips with thumb wheels x x x
Proportional control for excavators ALIX hydraulics x x x
Frequency I RPM (SG vibro) x x x
Impact energy rate (piling hammer) x x x
Movax angle (bucket cylinder operated) x x x
Movax angle (side tilt) x x x
Distance and height position NA x x
Auto Control NA optional x
Clamping force adjustment from cab NA x x
System diagnostics NA x x
MOVAX remoteTM optional optional optional
M-logbook NA optional optional
Camera Input NA optional optional
Wireless site camera on tripod NA optional optional
Software update via USB memory stick NA optional optional
The MOVAX Control System MCS Pro+auto is an advanced, state-of-the-art control system for easier, precise
and more productive and efficient operation.
MOVAX CONTROL SYSTEM
MCS Pro+auto
The visual user interface of the MCS Pro+auto is based on a 7″ display with easy-to-read graphical symbols for the position, vibro frequency or piling hammer impact energy rate, and hydraulic pressure. User-friendly menus for calibrating and optimising the performance of both the Movax equipment and the excavator hydraulics. The MCS Pro+auto provides full system diagnostics directly on the screen and can be set to remind the operator of critical maintenance tasks, such as changing oil and oil filter.
The control grips with proportional rollers are ergonomically shaped and designed for simultaneous control of multiple operations. The grips have a large number of switches and rollers to accommodate non-MOVAX functions as well.
The MCS Pro+auto control feature makes the excavator mounted MOVAX side grip pile drivers and piling hammers travel in a straight line by taking over a demanding part of the boom control. The system is based on angle sensors on the excavator and the MOVAX piling equipment and proportional pilot valves mounted on the excavator. The smart user interface allows the operator to switch the automatic control on or off at any time while keeping his/her hands on the controls at all times.
MCS Pro+auto can be upgraded to meet different needs. Versatile connectivity makes it possible to add pressure sensors, a boom-mounted camera or a wireless site camera for top-level safety, productivity and accuracy.
56
57
1. MOVAX module 2. Stick boom sensor / 3. Main boom sensor / 4. Excavator module / 5. Valve Block / 6. Grips / 7. Display
8. Camera (optional)
MOVAX CONTROL SYSTEM
MCS Pro+auto
1
2 3
4
5
6
7
MCS Lite is compatible with all SG-, DH-, TAD- and MPM-models as well as MOVAX piling equipment with AutoC system.
Note! The MOVAX module is provided with the MOVAX piling equipment.
FEATURES Lite Pro Pro+auto
Colour display 3.2” 7” 7”
Ergonomic control grips with thumb wheels x x x
Proportional control for excavators ALIX hydraulics x x x
Frequency I RPM (SG vibro) x x x
Impact energy rate (piling hammer) x x x
Movax angle (bucket cylinder operated) x x x
Movax angle (side tilt) x x x
Distance and height position NA x x
Auto Control NA optional x
Clamping force adjustment from cab NA x x
System diagnostics NA x x
MOVAX remoteTM optional optional optional
M-logbook NA optional optional
Camera Input NA optional optional
Wireless site camera on tripod NA optional optional
Software update via USB memory stick NA optional optional
8
The MOVAX M-logbook is a documentation and reporting tool which provides essential data related to the piling process.
The piling information collected by the MOVAX Control System (note! M-logbook requires MCS Pro+auto or MCS Pro) is stored in the MOVAX Control System’s excavator module. To report the piling works the operator only has to input the pile number, the system will take care of the rest. The data is then copied onto a USB-memory drive and transferred to a PC equipped with the M-logbook software for further analysis. Data concerning site and pile information is added and the system will generate illustrative, ready-made reports - including both measured and calculated data - which provide essential information about the piling process and its quality.
Specific reports are generated for MOVAX piling equipment including MOVAX side grip pile drivers and MOVAX piling hammers. The MOVAX side grip pile driver report includes information about the verticality and penetration rate whereas the MOVAX piling hammer report includes information related to the load bearing capacity of the pile.
58
MOVAX RemoteTM is a diagnostics-tool – available as an option to the MOVAX Controls System; MCS Lite, MCS Pro and MCS Pro+auto - which provides remote access to the performance data of the MOVAX piling and handling equipment. Access is provided both to recorded on-line data as well as to stored, historical data.
The MOVAX remote comes with a fully integrated GSM/ GPS-system providing the remote connection (GSM) as well as the location of the excavator (or other carrier) and MOVAX piling equipment (GPS). The MOVAX remote-module, including the GPS-antenna, is installed on the excavator. The recorded on-line-performance data and the stored historical data is accessed through an easy-to-use web-based, password-protected user interface (dashboard).
MOVAX Remote is utilised to monitor and optimise the performance of the MOVAX piling equipment. The monitored and stored data includes information about working hours, vibration hours, pressures, angles, frequencies and rpm’s as well as the impact energy (depending on the MOVAX piling or handling equipment in question). MOVAX Remote is also designed to assist in troubleshooting, analysis and fast and efficient problem solving.
MOVAX CONTROL SYSTEM
M-LOGBOOK™
MOVAX REMOTE™
59
SERVICES
INSTALLATION SUPERVISION & COMMISSIONINGMovax Oy provides on-site installation supervision and start-up & commissioning services to ensure proper installation and efficient and safe start-up of the equipment.
TRAINING Movax Oy’s comprehensive and versatile training ensures optimum performance and safe operation under all conditions throughout the entire life-cycle of the MOVAX equipment. Operational and maintenance training is provided by Movax Oy’s service engineer during start-up and commissioning.
Movax Oy also offers further, more detailed, operational and/or maintenance training at Movax Oy’s premises in Hämeenlinna, Finland, where also simulator-based training is available. These technical and practical training programmes can be tailored to meet any and all specific requirements.
MAINTENANCE, SERVICE AND SPARE PARTSMovax Oy offers reliable and professional service, repair and maintenance services. Daily problems are quickly solved by contacting our specialists and trouble-shooting services can be provided either remotely or at the customer’s premises or job site.
Movax Oy also maintains a large stock of spare and wear parts which can be delivered to most parts of the world within hours from order.
1/20
17 -
All r
ight
s res
erve
d
THE MOVAX-WAY-OF-PILINGFor higher productivity and significant savings
Movax Oy
Tölkkimäentie 10 FI-13130 Hämeenlinna, Finland
Tel. +358 3 628 070 Fax +358 3 616 1641
[email protected] www.movax.com
MOVAX Oy is represented by partners all over the world. Please refer to www.movax.fi for detailed contact information.