INJECTOR VALVE - CATTINI valve(PEEK)-ENG.pdf · 2016. 5. 4. · injector valve requires minimal...

02-04_INJECTOR VALVE(PEEK)-ENG.DOC CATTINI S.R.L. - via Giuseppe Verdi, 4 - 42018 San Martino in Rio (RE) ITA Tel.: +39 0522 695 220 Fax: +39 0522 695 254 web: http://www.cattini.it Certificata: UNI EN ISO 9001 - UNI EN ISO 14001 INJECTOR VALVE MOULDED MATERIAL PEEK FAMILY OF MATERIALS PAEK ; PEEK ; PEK ; PEEEK ; PEKK ; PEKEKK (Polyariletherketone) POLYMER’S FEATURES VICTREX ® PEEK materials are based on the polyeteretherketone resin. This high technology semi crystalline thermoplastic has a unique combination of mechanical properties, temperature resistance and chemical resistance that make it the best known among the so called «advanced plastic materials». – High maximum usage temperature in the air (250°C continuous temperature, up to 310°C for short period) – High mechanical resistance, creep stiffness and hardness, also at high temperatures – Excellent chemical and hydrolysis resistance – Excellent friction and wear resistance – Good dimensional stability – Low intrinsic flammability and very low flue gas emission during the combustion process – Good dielectric properties and electrical isolation (except for carbon- filled PEEK) – Excellent resistance to strong energy radiations (gamma and X-rays) – Low viscosity which allows you to create components with reduced thickness – In accordance to EU and FDA directives, concerning materials being in contact to food substances. These features, along with its excellent sterizability through steam, dry heat, ethylen oxide and gamma rays make this product particularly appreciated for medical, pharmaceutical and food applications. APPLICATION FIELDS Any fields where high performance polymers are needed, in this case, the injector valve requires minimal moisture absorption, high dimensional stability with temperature extremes, good adhesion properties of silicone resins or elastomers, surface finish to ensure the maintenance of gas and elasticity of the polymer to ensure the right impression with metallic elements closing, high resistance to chemicals. SPECIAL NOTES Cattini Engineering Plastics is recommended by: - VICTREX® : http://victrex.com -

Upload
others
Category

Documents
view
0
download
0

Embed Size (px):

Transcript of INJECTOR VALVE - CATTINI valve(PEEK)-ENG.pdf · 2016. 5. 4. · injector valve requires minimal...

02-04_INJECTOR VALVE(PEEK)-ENG.DOC

CATTINI S.R.L. - via Giuseppe Verdi, 4 - 42018 San Martino in Rio (RE) ITA Tel.: +39 0522 695 220 Fax: +39 0522 695 254 web: http://www.cattini.it

Certificata: UNI EN ISO 9001 - UNI EN ISO 14001

INJECTOR VALVE

MOULDED MATERIAL PEEK

FAMILY OF MATERIALS PAEK ; PEEK ; PEK ; PEEEK ; PEKK ; PEKEKK (Polyariletherketone)

POLYMER’S FEATURES

VICTREX ® PEEK materials are based on the polyeteretherketone resin. This high technology semi crystalline thermoplastic has a unique combination of mechanical properties, temperature resistance and chemical resistance that make it the best known among the so called «advanced plastic materials». – High maximum usage temperature in the air (250°C continuous

temperature, up to 310°C for short period) – High mechanical resistance, creep stiffness and hardness, also at high

temperatures – Excellent chemical and hydrolysis resistance – Excellent friction and wear resistance – Good dimensional stability – Low intrinsic flammability and very low flue gas emission during the

combustion process – Good dielectric properties and electrical isolation (except for carbon-

filled PEEK) – Excellent resistance to strong energy radiations (gamma and X-rays) – Low viscosity which allows you to create components with reduced

thickness – In accordance to EU and FDA directives, concerning materials being in

contact to food substances. These features, along with its excellent sterizability through steam, dry heat, ethylen oxide and gamma rays make this product particularly appreciated for medical, pharmaceutical and food applications.

APPLICATION FIELDS

Any fields where high performance polymers are needed, in this case, the injector valve requires minimal moisture absorption, high dimensional stability with temperature extremes, good adhesion properties of silicone resins or elastomers, surface finish to ensure the maintenance of gas and elasticity of the polymer to ensure the right impression with metallic elements closing, high resistance to chemicals.

SPECIAL NOTES

Cattini Engineering Plastics is recommended by: - VICTREX® : http://victrex.com -

http://en.wikipedia.org/wiki/Thermoplastichttp://victrex.com/
02-04_INJECTOR VALVE(PEEK)-ENG.DOC

CATTINI S.R.L. - via Giuseppe Verdi, 4 - 42018 San Martino in Rio (RE) ITA Tel.: +39 0522 695 220 Fax: +39 0522 695 254 web: http://www.cattini.it

Certificata: UNI EN ISO 9001 - UNI EN ISO 14001