INDUSTRIAL VALVES - ERAMCO · n PBM valves provide bidirectional upstream sealing. n Valve body...

INDUSTRIALVALVES

S 2-WaySERIES Valves

AN ANSI FlangedSERIES Valves

F Flush TankSERIES Valves

AF Angle StemSERIES Flush Tank

D 3-WaySERIES Diverter Valves

M 3, 4, & 5-WaySERIES Valves

TI TransmitterSERIES Isolation Valves

IM InstrumentSERIES Valves

FF Fabflex ManifoldSERIES Assemblies

S, AN V-ball ValvesSERIES for Flow Control

PA AutomationSERIES & Controls www.pbmvalve.com

2

PBM valves offer value over the life ofthe product with:n Fewer process interruptionsn Longer lifen Clean/drain without process interruptionn Improved product yields

PBM also offers:n On-time deliveryn Documentationn Solutions to tough applications

Adjust-O-Seal® featuren PBM valves provide bidirectional upstream sealing.

n Valve body bolts can be tightened to compensate for normal seat wear without having to remove the valve from service.

Seals atdownstream seat

Valve body bolts compress valve seatsagainst the ball, providing bidirectionalsealing at the upstream seat. Tocompensate for seat wear, body boltscan be slightly tightened to recompressseats against ball.

Line pressure pushes ball downstreamin the ball-closed position, providingsealing at the downstream seat. Thereis no adjustment to compensate forseat wear.

This means on valves mounted verticallylike PBM’s angle stem flush tank valve, thevalve seats on the upstream seat, thusallowing the body to be purged anddrained without process interruption.

PBM’s DesignCompetitor’s Design

Features

Seals at upstream seat

ITEM PAGE

Features 2

Ordering information 4-5

Materials of Construction 6

Seat & Seal materials 6

Allowable working pressures and temperature 7

Pressure and temperature charts; Cv factors 8

Torque values 9

Testing 1 0

Available options 1 0 - 1 1

Flow patterns 12-13

Specifications 14-15

DIMENSIONAL INFORMATION, MANUAL & AUTOMATED

S series 2-way 16-17

AN series ANSI 18-19

F series Flush Tank 20-21

AF series Angle Stem Flush Tank 22-23

D series 3-way Diverter 24-25

M series 3, 4, & 5-way Multi-port 26-29

TI series Transmitter Isolation valve 30

IM Series Instrument valves 31

Special Application valves 32-33

Automation 34-35

Rep locations 36

Table of Contents

3

Industrial Valves

Ordering Information for PBM Industrial ValvesNumber in "( )" represents part number position.

Product (1-2) Material (3-4) Size ( 5) Series (6) End Connection (7-8) Seat & Seal / Filler / O-ring (9)

SP Industrial 2-way H- 316 Stainless A 1/4" 1 ANSI, AF, Brz and Iron MP Q- Female NPT G TFM / None / Viton

SD Indust, Steam 2-way HL 316L Stainless B 3/8" 3 Firesafe ANSI, AF U- Socket Weld J TFM / VTFE / Viton

AN ANSI E- Carbon Steel C 1/2" 4 S/S and C/S MP B- Buttweld Sch 401A RTFE / None / Viton

FT Flush Tank 2-way N- 922 Bronze D 3/4" 5 Series 5 (SP, FT, DD, SD C- Buttweld Sch 51B RTFE / VTFE / Viton

AF Angle Stem FT C- Hastelloy C-276 E 1" DP, CT, SM, SB, SA, FA D- Buttweld Sch 101C VTFE / None / Viton

DP Diverter Port 3-way C1 Hastelloy B-2 F 1 1/4" 6 Series 5 Firesafe 2-way only L- 150# Flange D VTFE / VTFE / Viton

DD Diverter Steam Y- Hastelloy C-22 G 1 1/2" M- 300# Flange H S-tefTM / None / Viton

MP Multi-port B- 836 Bronze H 2" N- 600# Flange I S-tefTM / VTFE / Viton

TI Transmitter Isolation R- 955 Al-Brz J 2 1/2" O- Grooved K UHMWPE / None / Viton

X- 958 Ni-Al-Brz K 3" K- Cam Lock L UHMWPE / VTFE / Viton

9- 954 Al-Brz L 4" P- Male NPT M UHMWPE / UHMWPE / Viton

Z- 70/30 Cu-Ni M 6" R- Sil Braze N PEEK / None / Kalrez

1- 90/10 Cu-Ni N 8" S- Sil Braze (1) Groove O PEEK / VTFE / Kalrez

P- AL6XN P 10" T- Solder Joint P PEEK / PEEK / Kalrez

I- Inconnel 600 W- Tri-Clamp Pipe Q Carbon - Graphite

M- Monel 400 -Z No End Fittings R Kynar / None / Viton

S- 953 Al-Brz S Kynar / Kynar / Viton

T- Gr 5 Titanium T VTFE / None / EPR

W- Nickel 200 Notes: U VTFE / VTFE / EPR

D- Iron 1. Extended butt weld end fittings are standard V RTFE / None / EPR

A- Aluminum on Series 5 & 6 valves. W RTFE / VTFE / EPR

25 254 SMO 6 -moly 2. All options are not available on all valve styles Z TFM / None / EPR

22 Duplex 2205 3. For valves with (2) different end connections, use 0 S-tefTM / None / EPR

76 Super duplex both end codes, for example LQ = 150# flanged 1 S-tefTM / VTFE / EPR

32750 / 32760 by female NPT 2 TFM / VTFE / EPR

55 Ferralium 255 3 UHMWPE / None / EPR

4 UHMWPE / VTFE / EPR

5 UHMWPE / UHMWPE / EPR

6 PEEK / None / Viton

7 VTFE / None / Encapsulated Viton

8 RTFE / None / Encapsulated Viton

INDUSTRIAL VALVES (Series 5) 9 TFM / None / Encapsulated Viton

Industrial 2-way SP

Industrail flush tank FT TFMTM is standard for Seres 5 & 6

Industrail diverter valve 3 way DP RTFE is standard seat material

for Series 1 valves.TFMTM is a registered trademark

of DyneonTM, a 3M Company

S-TEFTM is 50% 316 stainless steel

and 50% PFFE.

- -

www.pbmvalve.comPBM, Inc. Valve Solutions - 1070 Sandy Hill Road - Irwin, PA 15642 - Phone: 724.863.0550 - Fax: 724.864.9255 - Email: [email protected]

SD

FD

DD

VALVE TYPE STANDARD SEATS ENCAPSULATED SEATS STEAM SERVICE

Standard Options 1 + 2 3 + 4 5 6 7 + 8 9 10 + 11 12 13 + 14 15

Product Material Size Series End Fitting Seat/Seal Flow Pattern Ball/Stem Operator Polish

Purge Ports. Ball Flats

SP H- H 5 Q- G - - G 34 - SPH-H5Q-G—G34- is the code for a SP Industrial 2 -way, 316 stainless steel, 2 inch size, Series 5, FNPT end connections, TFM™ seats and seals, 17 -4 PH stem, 80 psig Spring Return Actuator.

Ordering Information for PBM Industrial Valves cont.

Flow Pattern / Flush Tank Pad / Aseptic (Pos 10-11) Ball / Stem (Pos 12) Operator (13-14) Polish (15) (max values)

For Non-Flow Pattern, Non-Flush Tank, Non Aseptic, Use " - - " - Standard - - w/ lever operator - No polish

For Valves with Flow Patterns, enter the 2 digit flow pattern no. B w/4" stem extension 01 w/o handle A 20 RA ID

For all non-aseptic Flush Tank Valves, Use codes below E w/4" stem ext, & internal 02 w/o handle, w/ actuator prep B 32 RA OD

- - Standard Flush Tank Pad and external ground 03 w/ handle, w/ actuator prep. C 20 RA ID, 32 RA OD

02 No Pad w/ shipping pad F w/ internal and external 04 w/ locking handle D 15 RA ID

04 w/ 316L barstock pad ground 05 w/ stainless oval handwheel E 10 RA ID

05 w/ 1" bolt on flat pad G w/ 17-4 PH stem 06 w/ manual safety nut F 20 RA ID after

06 w/ 1.5" bolt on flat pad I w/ monel ball 07 w/ 45 degree handle electropolish

07 w/ 2" bolt on flat pad J w/ 932 bronze ball 08 w/ gear operator G 15 RA ID after

08 w/ 3" bolt on flat pad K w/ monel stem, followers 09 w/ T handle electropolish

09 w/ 4" bolt on flat pad L w/monel ball, stem, 10 w/ manual spring return handle H 10 RA ID after

10 w/ 6" bolt on flat pad and followers 11 w/ fusible link spring return electropolish

11 w/ 8" bolt on flat pad M w/ aluminum ball handle I 5 RA ID

N w/ 922 bronze ball 12 w/ vane actuator for 80 psig K 5 RA ID & 32 RA OD

For all aseptic valves, use the codes below: O w/ hastelloy C-276 ball 13 w/ nema 4 120 VAC electric actr L 20 RA ID & 32 RA OD

Purge Ports (10) Ball Flats & holes (11) P w/ has C-276 ball,stem, 14 w/ nema 7 120 VAC electric actr after electropolish

M (1) 1/4" FNPT on center, 90 #1 #2 Use column #1 for and followers 15 w/ square operating nut M Electropolish only

degrees from stem 2 way or aseptic FT Q w/ 922 ball, monel stem 16 w/ locking handle,w/ actr mount (ID & OD)

N (1) 1/4" FNPT on center, w/ std. Pad. Use and followers body N 10 RA ID & 32 RA OD

opposite stem column #2 if valve is R w/ monel stem, followers 17 w/ 4" ext. locking oval handwheel O 15 RA ID & 32 RA OD

O (1) 1/4" FNPT upstream, 90 aseptic FT with and bolting 18 w/ 4" ext. locking lever handle after electropolish

degree from stem shipping pad. S w/monel ball,stem, 20 w/ DA 80 psig actr. Q 15 RA ID & 32 RA OD

P (1) 1/4" FNPT downstream, A K flats, closed. dwnstrm followers and bolting 21 w/ DA 80 psig actr., N 4 L.S. S 10 RA ID & 32 RA OD

opposite stem B L flats, closed, upstrm T w/ 922 ball, monel stem & 22 w/ DA 80 psig actr, N 4 Sol. after electropolish

Q (2) 1/4" FNPT on center, 90 C M flats, open, upstrm followers, sil-brz bolting 23 w/ DA 80 psig actr, N 4 L.S. & Sol.

degree from & opposite stem D N flats, open, dwnstrm U with CuSi fasteners 24 w/ DA 80 psig actr, N 7 L.S.

R (2) 1/4" FNPT upstream, 90 E O flats, open, up & 25 w/ DA 80 psig actr, N 7 Sol. Optional 16th Position

deg frn & dwnstream opp stem downstream 26 w/ DA 80 psig actr, N 7 L.S. & Sol. LOX Cleaning (16)

- no purge. Use only if adding F P holes, closed, dwnstr 27 w/ DA 60 psig actr. L Oxygen Service Cleaning

ball flats or drain holes G Q holes, closed, upstrm 28 w/ DA 60 psig actr., N 4 L.S. per PBM Procedure

H R holes, open, upstrm 29 w/ DA 60 psig actr, N 4 Sol.

I S holes, open, dwnstrm 30 w/ DA 60 psig actr, N 4 L.S. & Sol.

J T holes, open, up & 31 w/ DA 60 psig actr, N 7 L.S.

downstream 32 w/ DA 60 psig actr, N 7 Sol.

- U No flats or holes 33 w/ DA 60 psig actr, N 7 L.S. & Sol.

V 2 std width slotted ball 34 w/ SR 80 psig actr. Operator (13-14) continued

W 3 30 degree V ball 35 w/ SR 80 psig actr., N 4 L.S. Codes for Asco Limit Switch

X 4 45 degree V ball 36 w/ SR 80 psig actr, N 4 Sol. 55 w/ DA 80 actr., N 4 L.S.

Y 5 60 degree V ball 37 w/ SR 80 psig actr, N 4 L.S. & Sol. 56 w/ DA 80 actr, N 4 L.S. & Sol.

Z 6 90 degree V ball 38 w/ SR 80 psig actr, N 7 L.S. 57 w/ DA 80 psig actr, N 7 L.S.

1 7 120 degree V ball 39 w/ SR 80 psig actr, N 7 Sol. 58 w/ DA 80 actr, N 7 L.S. & Sol.

8 9 self flushing ball 40 w/ SR 80 psig actr, N 7 L.S. & Sol. 59 w/ DA 60 psig actr., N 4 L.S.

41 w/ SR 60 psig actr. 60 w/ DA 60 actr, N 4 L.S. & Sol.

42 w/ SR 60 psig actr., N 4 L.S. 61 w/ DA 60 psig actr, N 7 L.S.

43 w/ SR 60 psig actr, N 4 Sol. 62 w/ DA 60 actr, N 7 L.S. & Sol.

44 w/ SR 60 psig actr, N 4 L.S. & Sol. 63 w/ SR 80 psig actr., N 4 L.S.

45 w/ SR 60 psig actr, N 7 L.S. 64 w/ SR 80 actr, N 4 L.S. & Sol.

46 w/ SR 60 psig actr, N 7 Sol. 65 w/ SR 80 psig actr, N 7 L.S.

47 w/ SR 60 psig actr, N 7 L.S. & Sol. 66 w/ SR 80 actr, N 7 L.S. & Sol.

51 w/ DA 80 psig actr, beacon 67 w/ SR 60 psig actr., N 4 L.S.

52 w/ DA 60 psig actr, beacon 68 w/ SR 60 actr, N 4 L.S. & Sol.

53 w/ SR 80 psig actr, beacon 69 w/ SR 60 psig actr, N 7 L.S.

54 w/ SR 60 psig actr, beacon 70 w/ SR 60 actr, N 7 L.S. & Sol.

www.pbmvalve.comPBM, Inc. Valve Solutions - 1070 Sandy Hill Road - Irwin, PA 15642 - Phone: 724.863.0550 - Fax: 724.864.9255 - Email: [email protected]

UNIQUE PART NUMBERS, FXXX, GXXX, HXXX

"-XXX designates a unique part number where PBM's traditional part number cannot completely describe the valve. For Example, a sepecial actuator, solenoid, etc.

Designation Description Color Purpose

TFM®

Chemically ModifiedPTFE

PBM Standard for Series 5 & 6

White

This chemically modified PTFE material is PBM’s standard seat and seal material.It combines the ruggedness of a filled PTFE with the low coefficient of friction ofvirgin PTFE. TFM also has much improved porosity control and deformationunder load when compared to PTFE grades. FDA and USP Class VI compliant.Meets bubbletight seat leakage.

RTFE Glass Reinforced PTFE Slightly OffWhite

Used in a wide variety of applications. Bubbletight leakage.

VTFE Virgin PTFE WhiteA low stem torque material ideal for sanitary use. FDA and USP Class VIcompliant. Meets bubbletight seat leakage.

S-TEFTM Stainless Steel Reinforced PTFE

CharcoalGray

A suitable material for higher pressure/temperature applications. Higher stemtorque than virgin grades and TFM. USP Class VI compliant. Meets bubbletightseat leakage.

CARBON Carbon/Graphite BlackA hard material impervious to high temperatures. Can withstand up to 750˚F(400˚C) and is used for heat transfer fluid applications and other high temperatureapplications. Meets Class V seat leakage.

UHMWPEUltra High MolecularWeight Polyethylene Off White

Suitable for applications under 200˚F. An extremely wear resistant material havinga wear rate about 1/10th that of PTFE. FDA compliant and is used in high cycleapplications where possible. Meets bubbletight seat leakage.

PEEK Poly ether ether ketone PuttyFor applications up to 500˚F. PEEK is a rugged, high strength material havingfairly high stem torque. PBM’s PEEK is 10 weight percent PTFE to reduce thehardness of virgin PEEK. FDA compliant and meets Class V seat leakage.

KYNAR® Polyvinylidene FluorideSlightly

TransparentWhite

Suitable for applications under 250˚F. Kynar has been used successfully inabrasive service and is suitable for radiation environments where gamma levelsaccumulate to 1,000 megarads. FDA and USP Class VI compliant. Meetsbubbletight seat leakage.

NOTES:1. PTFE is Polytetrafluorethylene.2. Seat and seal materials may be mixed in a valve in order to provide media-compatibility and the appropriate torque, temperature and pressure ratings.

Stainless Steel316 S/S complies with ASTM A 351-CF8M or A 4 7 9 , S 3 1 6 0 0316L S/S complies with ASTM A 351-CF3M or A479, S31603• Is exceptionally corrosion-resistant to acidic and basic environments and does not pit easily.• Can be polished to a near-mirror finish for easy cleanability.• Weld fittings have a carbon content of <.03% to facilitate welding.

Carbon Steel, A 2 1 6 - W C B• This versatile material handles mildly corrosive media.

B ronze, A l l oy 922• Excellent resistance to sea water environments and good steam resistance. Also, suitable for sub-zero tempera t u r e

a p p l i c a t i o n s .

H a s t e l l oy C-276• Very good corrosion in reducing and mildly oxidizing environments. Very good resistance to localized attack and ve r y

good resistance to stress corrosion cra cking. A l l oy CW-12MW in cast form. Others • Additional materials are available, including A l l oy 20, Bronze, Duplex Stainless Steels, Hastelloys, Titanium, and Inconel.

Industrial Valves Materials

Seat and Seal Materials

6

Industrial ValvesAllowable Working Pressures and Temperatures

ValveStyle/Series

Material Size (inches)

Non-Flanged 150# Flanged

-20 to100˚F

-28.9 to37.8˚C 300˚F 1 4 8 . 9˚C 450˚F 232.2˚C -20 to

100˚F-28.9 to37.8˚C 300˚F 1 4 8 . 9˚C 450˚F 232.2˚C

psig barg psig barg psig barg psig barg psig barg psig barg

Series 5SP, SD,DP, DD

316 SS/316L 1-1/2” (DN40) and smaller 900 62.1 770 53.1 680 46.9 275 19.0 205 14.1 195 13.4

316 SS/316L 2” and larger 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4

C-276 1-1/2” (DN40) and smaller 600 41.4 520 35.9 450 46.9 230 15.9 200 13.8 180 12.4

C-276 2” (DN50) and larger 600 41.4 520 35.9 450 46.9 230 15.9 200 13.8 180 12.4

Carbon Stl. 1-1/2” (DN40) and smaller 900 62.1 770 53.1 680 46.9 285 19.7 230 15.9 185 12.8

Carbon Stl. 2” (DN50) and larger 740 51.0 655 45.2 620 42.7 285 19.7 230 15.9 185 12.8

922 Bronze 1-1/2” (DN40) and smaller 600 41.4 600 41.4 580 40.0 225 15.5 180 12.4 135 9.3

922 Bronze 2” (DN50) and larger 600 41.4 600 41.4 580 40.0 225 15.5 180 12.4 135 9.3

SP, FT,Series 6

316 SS/316L 3” (DN80) and under 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4

Carbon Stl. 3” (DN80) and under 740 51.0 655 45.7 620 42.7 285 19.7 230 15.9 185 12.8

ANSeries 1and 3

150# Class

316 SS/316L All n/a n/a n/a 275 19.0 205 14.1 195 13.4

C-276 All n/a n/a n/a 230 15.9 200 13.8 180 12.4

Carbon Stl. All n/a n/a n/a 285 19.7 230 15.9 185 12.8

836 Bronze All n/a n/a n/a 225 15.5 180 12.4 135 9.3

MPAll Series 1

836 Bronze 1-1/2” (DN40) and smaller 400 27.6 385 26.5 360 24.8 225 15.5 180 12.4 135 9.3

836 Bronze 2” (DN50) 350 24.1 340 23.4 315 21.7 225 15.5 180 12.4 135 9.3

836 Bronze 3” (DN80) 300 20.7 290 20.0 270 18.6 225 15.5 180 12.4 135 9.3

836 Bronze 4” (DN100) n/a n/a n/a 225 15.5 180 12.4 135 9.3

MP,All Series 4

316 SS/316L 3/4” (DN20) and smaller 900 62.1 770 53.1 680 46.9 275 19.0 205 14.1 195 13.4

316 SS/316L 1” (DN 25) thru 4” (DN100) 720 49.6 620 42.7 540 37.2 275 19.0 205 14.1 195 13.4

316 SS/316L 6” (DN150) 275 19.0 205 14.1 195 13.4 275 19.0 205 14.1 195 13.4

C-276 3/4” (DN20) and smaller 900 62.1 770 53.1 680 46.9 230 15.9 200 13.8 180 12.4

C-276 1” (DN25) thru 4” (DN100) 720 49.6 620 42.7 540 37.2 230 15.9 200 13.8 180 12.4

C-276 6” (DN150) 275 19.0 205 14.1 195 13.4 230 15.9 200 13.8 180 12.4

Carbon Stl. 3/4” (DN20) and smaller 900 62.1 770 53.1 680 46.9 285 19.7 230 15.9 185 12.8

Carbon Stl. 1” (DN25) thru 4” (DN100) 740 51.0 655 45.7 620 42.7 285 19.7 230 15.9 185 12.8

Carbon Stl. 6” (DN150) 300 20.7 250 17.2 220 15.2 285 19.7 230 15.9 185 12.8

AF Series 1


316 SS/316L 2” (DN50), 4” (DN100) 550 37.9 540 37.2 525 36.2 275 19.0 205 14.1 195 13.4

316 SS/316L 3” (DN80) 625 43.1 610 42.1 6 0 0 46.9 275 19.0 205 14.1 195 13.4

316 SS/316L 6” (DN150) 375 25.9 3 6 5 25.2 360 24.8 275 19.0 205 14.1 195 13.4

C-276 1-1/2” (DN40) and smaller 600 41.4 520 35.9 475 32.8 230 15.9 200 13.8 180 12.4

C-276 2” (DN50), 4” (DN100) 550 37.9 540 37.2 525 36.2 230 15.9 200 13.8 180 12.4

C-276 3” (DN80) 600 41.4 520 35.9 475 32.8 230 15.9 200 13.8 180 12.4

C-276 6” (DN150) 375 25.9 320 22.1 280 19.3 230 15.9 200 13.8 180 12.4


Carbon Stl. 2” (DN50) 550 37.9 550 37.9 550 37.9 285 19.7 230 15.9 185 12.8

Carbon Stl. 3” (DN80) 625 43.1 625 43.1 625 43.1 285 19.7 230 15.9 185 12.8

Carbon Stl. 4” (DN100) 550 37.9 550 37.9 550 37.9 285 19.7 230 15.9 185 12.8

Carbon Stl. 6” (DN150) 375 25.9 375 25.9 375 25.9 285 19.7 230 15.9 185 12.8

AF Series 3


316 SS/316L 2” (DN50), 4” (DN100) 550 37.9 540 37.2 525 36.2 275 19.0 205 14.1 195 13.4

316 SS/316L 3” (DN80) 625 43.1 610 42.1 600 41.4 275 19.0 205 14.1 195 13.4

316 SS/316L 6” (DN150) 375 25.9 365 25.2 360 24.8 275 19.0 205 14.1 195 13.4


Carbon Stl. 2” (DN50), 4” (DN100) 550 37.9 550 37.9 550 37.9 285 19.7 230 15.9 185 12.8

Carbon Stl. 3” (DN80) 625 43.1 625 43.1 625 43.1 285 19.7 230 15.9 185 12.8

Carbon Stl. 6” (DN150) 375 25.9 375 25.9 375 25.9 285 19.7 230 15.9 185 12.8

FT, FDSeries 5

FD Series 6

316 SS/316L All 720 49.6 620 42.8 540 37.2 275 19.0 205 14.1 195 13.4

C-276 All 720 49.6 620 42.8 540 37.2 230 15.9 200 13.8 180 12.4

Carbon Steel All 740 51.0 655 45.2 620 42.8 285 19.7 230 15.9 185 12.8

TIV Series

316 SS/316L All n/a n/a n/a 275 19.0 205 14.1 195 13.4

317L SS All n/a n/a n/a 275 19.0 205 14.1 195 13.4

C-276 All n/a n/a n/a 230 20.0 200 15.9 180 12.4

Ti Grade 5 All n/a n/a n/a 275 19.0 240 16.5 200 13.8

7

Notes: 1. Bronze, 316 SS and C-276 retain their CWP below minus 20˚F.2. All valves rated for full vacuum.

Industrial Valves

VALVESIZE

2-WAY FLUSH TANK DIVERTER PORTSP AN AF FT DP SERIES 5 S/S DP SERIES 1 BRONZE

L-PORT T-PORT L-PORT T-PORTSERIES 5 SERIES 1 SERIES 1 SERIES 5 STRAIGHT BRANCH STRAIGHT BRANCH

1/4" 5*3/8" 10*1/2" 12 31 14 6.6 7.4 5.2 12 14 8.73/4" 42* 52 42 17 20 13 21 25 161" 73 80 65 70 33 39 24 33 39 24

1-1/4"1-1/2" 170 190 143 190 79 93 58 79 93 58

2" 360 400 280 370 149 180 110 149 180 1102-1/2" 650 600

3" 935 1,100 700 900 350 415 250 290 345 2104" 1,900 2,400 8 8 0 1,650 640 770 465 460 540 3406" 4,800 5,600 1,500 3,900 1,550 1,860 1,110 1,050 1,220 7908" 10,700 7,400

10" 17,400 150# Flanged and Butt Weld, unless indicated otherwise noted (gpm at 1 psi d/p)

VALVESIZE

MULTI-PORTMP SERIES 4 (S/S, CARBON) MP SERIES 1 (BRONZE, DUCTILE)

L-PORT T-PORT LL-PORT L-PORT T-PORT LL-PORTSTRAIGHT BRANCH STRAIGHT BRANCH

1/2" 6.6 7.4 5.2 6.6 12 14 8.7 6.63/4" 17 20 13 16 17 20 13 161" 33 39 24 27 33 39 24 27

1-1/4" 32 36 23 26 32 37 23 261-1/2" 79 93 58 73 79 93 58 73

2" 149 180 110 128 149 180 110 1283" 350 415 250 300 200 250 140 1804" 640 770 465 530 365 450 260 3406" 1,550 1,860 1,110 1,210 1,550 1,860 1,110 770

Cv Values

8

*Q (FNPT) ends

Valves 1-1/2-Inch and Smaller

0

100

200

300

400

500

600

700

800

900

1000

0 50 100 150 200 250 300 350 400 450 500

Temperature (F)

Pre

ssu

re (

psi

g)

UHMWPEVTFERTFE/TFMSS/TFEPEEK

4 and 6-Inch

0

100

200

300

400

500

600

0 50 100 150 175 200 250 300 350 400 450 500

Temperature (F)

Pre

ssu

re (

psi

g)

UHMWPE

VTFE

RTFE/TFM

SS/TFE

PEEK

Seat & SealTemperatureand Pressure

Charts

2-Inch to 3-Inch

0

100

200

300

400

500

600

700

800

0 100 200 300 400 500 600

Temperature (F)

Pre

ssu

re (

psi

g) UHMWPE

VTFE

RTFE/TFM

SS/TFE

PEEK

1-1/2” and smaller 2” to 3”

4” to 6”

ValveStyle/Series

ValveSize(in.)

As builtTorque

Differential Pressure across Seats

0psig

0barg

100psig

6.9barg

200psig

13.8barg

300psig

20.7barg

400psig

27.6barg

500psig

34.5barg

600psig

41.4barg

700psig

48.3barg

in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m in.-lb. N-m

AllSeries5 & 62-Wayand 3-Way

1/4 32 3.6 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2

1/2 32 3.6 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2 64 7.2

3/4 40 4.5 80 9.0 80 9.0 80 9.0 80 9.0 80 9.0 96 10.8 112 10.8 128 12.7

1 58 6.6 116 13.1 116 13.1 116 13.1 150 16.9 185 20.9 220 24.9 trun.1-1/2 154 17.4 308 34.8 308 34.8 440 49.7 580 65.5 715 80.8 trun. trun.

2 182 20.6 364 41.1 364 41.1 635 71.7 910 102.8 1,180 133.3 trun. trun.

2-1/2 288 32.5 576 65.1 576 65.1 1,200 135.6 1,600 180.8 trun.

3 430 48.6 860 97.2 860 97.2 1,560 176.3 trun. trun.

4 787 88.9 1,570 177.4 2,650 299.4 trun. trun.

6 1,920 217.0 3,840 433.9 7,100 8 0 2 . 3 Use trunnion above 75 psid.

ANSeries

1and3

1/2 32 3.6 64 7.2 64 7.2 64 7.2 64 7.2

3/4 4 0 4.5 80 9.0 80 9.0 80 9.0 80 9.0

1 60 6.8 120 13.6 120 13.6 120 13.6 120 13.6

1-1/2 132 14.9 264 29.8 264 29.8 280 31.6 390 4 4 . 1

2 156 17.6 312 35.3 312 35.3 545 61.6 785 88.7

3 336 38.0 672 75.9 1,050 118.7 1,950 220.4 trun. trun.4 720 58.6 1,440 162.7 2,650 299.5 trun. trun.

6 1,560 176.3 3,120 352.6 7,100 802.3 Use trunnion above 75 psid.

MPSeries

1

1/2 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3

3/4 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3

1 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5

1-1/4 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.51-1/2 384 43.4 770 87 770 87 770 87 940 106.2 trun. trun.

2 432 48.8 865 97.7 865 97.7 865 97.7 1,200 135.6 trun. trun.

3 576 65.1 1,150 129.9 1,150 129.9 1,620 183 2,100 237.3 trun. trun.

4 864 9 7 . 6 1,700 192.1 3,000 339 trun. trun.

MP Series

4

1/2 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3

3/4 77 8.7 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3 144 16.3

1 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 440 49.7 trun. trun.

1-1/4 192 21.7 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 385 43.5 440 49.7 trun. trun.

1-1/2 384 43.4 770 87 770 87 770 87 940 106.2 trun. trun.

2 432 48.8 865 97.7 865 97.7 865 97.7 1,200 135.6 trun. trun.

3 864 97.6 1,730 195.5 1,730 195.5 trun. trun.

4 1,920 216.9 3,840 433.9 3,840 433.9 trun. trun.

6 3,000 339.0 6,000 678.0 8 , 8 0 0 994.4 Use trunnion above 75 psid.

Minimum Actuator Sizing Torque vs. Differential PressureTFM® or VTFE Seats

Notes: 1. For valves with UHMWPE and RTFE seats, multiply the above values by 1.252. For valves which have SS/TFE or Kynar seats multiply the above values by 1.56.3. For valves with PEEK seats multiply the above values by 1.7.4. Where trunnion is indicated, PBM recommends trunnion mounting the ball to avoid excessive seat loads and stem torques.5. For Series 5 SD valves, 2-1/2” and larger, with RTFE seats, multiply the torques in the table by 1.56.

Stem TorqueIndustrial Valves

9

Industrial Valves Testing

Steam Valves

10

Options

n Cryogenic n USCG Category An Manual Spring Return Handles n Internal & External Groundingn LOX (Cleaned for Oxygen Service) n Mechanical & Electro-Polishingn Body Cavity Fillers n Direct Mount Actuationn Steam Seats (Encapsulated) n Positionersn Purge Ports (SIP/CIP) n Fieldbus, AS-i, DeviceNetn Fire Rated, API 607 n Ball Flats or Purge Holesn Dribble Control Units n Locking Handlen High Alloys n Extended Locking Handlen Fabflex® Manifolds n Cylindrical Radius Weld Padsn Self Cleaning Flushable Ball n V-Balls for Flow Control

n Vacuum Testingn Cycle Testingn Shock and Vibrationn Seismicn Hydrostaticn Material Test Reports

- Physical testing- Chemical testing

Options

Industrial Valves

Locking Handle

Purge Ports, Milled Flats andPurge Holes

Cylindrical Radius Pad

Cavity Fillers

Direct Mount Actuation

11

Industrial Valves

The diagrams show the top view as though you were looking down on the stem. White areas indicate the path available forprocess flow. Shaded areas indicate unused ports for a given flow position.

C o d e 0 3 0 4 0 6 10 T- Po r t T- Po r t T- Po r t L - Po r t

90° Tu r n 90° Tu r n 180° Tu r n 90° Tu r n

1 4 1 5 1 6 1 7 1 8L - Po r t L - Po r t T- Po r t T T- Po r t L L - Po r t360° Tu r n 180° Tu r n 90° Tu r n 180° Tu r n 90° Tu r n

Position A

Position B

Position C

3 - way Multi-Ports are a popular choice in a variety of industries. Aseal at every port distinguishes the 3-way MP/MI Series va l ve fromd iverting-type va l ves. In some applications, the 3-way MP/MI va l vecan take the place of two or three 2-way va l ves, with correspondings avings in piping and fittings. For applications requiring simultaneousprocess line changes, two 3-way MP/MI Series va l ves may be mountedin tandem and controlled with a single actuator or handle for greatercontrol and additional savings. Additional flow patterns are possibleby using manifolds of two or more va l ve s .

Position A

Position B

Position C

Position D

Diverter Port Patterns

Flow Pattern Diagrams

3-Way Multi-Port Patterns

1 4 1 5 1 6 1 7 1 8 1 9

L - Po r t L - Po r t T- Po r t T T- Po r t L L - Po r t L - Po r t360° Tu r n 180° Tu r n 90° Tu r n 180° Tu r n 90° Tu r n 90° Tu r n

Position A

Position B

Position C

Position A

Position B

Position C

Position D

Position A

Position B

Position C

Position D

0 1 0 2 0 3 0 4 0 5 0 6 0 7

T- Po r t T- Po r t T- Po r t T- Po r t T- Po r t T- Po r t T- Po r t90° Tu r n 90° Tu r n 90° Tu r n 90° Tu r n 180° Tu r n 180° Tu r n 180° Tu r n

0 8 0 9 1 0 1 1 1 2 1 3

T- Po r t T- Po r t L - Po r t L - Po r t L - Po r t L - Po r t180° Tu r n 360° Tu r n 90° Tu r n 180° Tu r n 180° Tu r n 360° Tu r n

By specifying a T- Port, Double T- Port, Angle Port (L) or DoubleAngle Port (LL) Ball, different flow configurations are possible.For example, a DP va l ve with a T- Port Ball might be used tocontrol flow to one or two simultaneous operations. The sideentry Angle Port Ball and the bottom entry Double Angle Po r tBall are ideal for connecting two relief va l ves to a system. Th eDouble Angle Port Ball diverts flow from one outlet to anotheroutlet 180° away, with only 90° stem rotation. This allows use of90° double acting or spring return actuation, instead of 180°.

SIDE ENTRY

2

BOTTOM

ENTRY

BOTTOM

ENTRY

SIDE ENTRY

4 - way Multi-Ports are a true Multi-Port va l ve with seals at eve r yport. This design makes the 4-way MP/MI Series ideal for flowsw i t ching operations. In some applications, this va l ve canreplace as many as four ordinary 2-way va l ves, withcorresponding savings in piping and fittings. The follow i n gi l l u s t rations show how different ball and port configura t i o n screate many flow patterns with a single 4-way Multi-Po r t .

5 - way Multi-Ports are 5-seated to provide positive shut off and flowcontrol at each port. This design is not only versatile, but extremelyeconomical. In some applications, this va l ve can replace as many asfour ordinary 2-way va l ves, with corresponding savings in pipingand fittings. The following illustrations show available flow patternswith a single 5-way Multi-Port va l ve.



Industrial Valves

Position A

Position B

Position C

Position D

Position A

Position B

Position C

Position D

2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7

Double L-Po r t Double L-Po r t Double L-Po r t Double L-Po r t Double L-Po r t Double L-Po r t L - Po r t T- Po r t

90° Tu r n 180° Tu r n 180° Tu r n 180° Tu r n 180° Tu r n 360° Tu r n 360° Tu r n 90° Tu r n

2 8 2 9 3 0 3 1 3 2 3 3 3 4 3 5

Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t180° Tu r n 180° Tu r n 180° Tu r n 180° Tu r n 360° Tu r n 90° Tu r n 90° Tu r n 90° Tu r n

3 7 3 8 3 9 4 0 4 1 4 2 4 3

Double L-Po r t L - Po r t L - Po r t T- Po r t S t raight Po r t T- Po r t T- Po r t90° Tu r n 180° Tu r n 360° Tu r n 180° Tu r n 90° Tu r n 90° Tu r n 90° Tu r n

4 4 4 5 4 6 4 7 4 8 4 9 5 0 5 1

L - Po r t Double L-Po r t T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double T- Po r t Double L-Po r t360° Tu r n 180° Tu r n 90° Tu r n 90° Tu r n 90° Tu r n 180° Tu r n 360° Tu r n 360° Tu r n


3 6

Double T- Po r t90° Tu r n

BOTTOM

ENTRY

BOTTOM

ENTRY

SIDE ENTRY

13

Written SpecificationsS SERIES

S-Series 5: Two - way full port ball va l ve; Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, CarbonSteel, Hastelloy C-22, bronze alloy 922, or other. Va l ve shall be three-piece “ swing-out” body design. Seats and seals shall be T F M®- P T F Ematerial and provide both upstream and dow n s t ream bubbletight seal and be adjustable for in-line we a r. Stem packing shall be live loadedT F M®-PTFE material. For manual va l ves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel.Maximum working pre s s u re to be 720 psig and full vacuum. Va l ves shall be non-firesafe design unless otherwise specified. For fire ra t e dva l ves to API 607 Ed 4, sizes 1/2” – 3”, designate Series 6 (see section “ f i re rated”). To add automation and controls, see section“Automation and Controls”. PBM Model number SP(material)-(size)5(end connection)

SD Series 5: Two - way full port steam ball va l ve; Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276,Carbon Steel, Hastelloy C-22, bronze alloy 922, or other. Va l ve shall be three-piece “ swing-out” body Seats shall be T F M®-PTFE with EPRO-ring energizer. Seats shall have stainless steel encapsulation on ID, provide both upstream and dow n s t ream bubbletight seal and beadjustable for in-line we a r. Stem packing shall be live loaded white T F M®-PTFE. Body seal shall be EPR o-rings with white T F M®- P T F Eb a ck up seal. Optional 300 Series s/s 2” stem extension for 4” thick installation. Va l ves shall not re q u i re disassembly for buttwelding. Bodybolts, nuts, and belleville washers shall be 18-8 stainless steel. Body bolts shall be live-loaded with belleville washers. Maximum wo r k i n gp re s s u re to be 720 PSIG and full vacuum. Va l ves shall be a non-firesafe design. To add automation and controls, see section “Au t o m a t i o nand Controls”. PBM Model number SD(material)-(size)5(end connection)

AN SERIES

Series 1 ANSI: Two-way ANSI flanged full port ball valve; B o dy, ball, stem, and end fitting material shall be 316 stainless steel, HastelloyC-276, Carbon Steel, bronze, aluminum bronze, or other. Valve shall be two piece “split body” design. Seats and seals shall be RTFEmaterial, with Viton O-ring body seal. Seats shall provide both upstream and downstream bubbletight seal and be adjustable for in-linewear. Stem packing shall be live loaded RTFE material. End fittings shall be ANSI 150# flanged per ANSI B16.5 and face to facedimension shall conform to ASME B16.10 Long Pattern. Valve handle shall be 300 series stainless steel with optional pad locking deviceallowing valve to pad locked in the open or closed position. Body bolts and nuts shall be 18-8 stainless steel. Maximum workingpressure to be as material is rated for 150# flanges to and full vacuum. Valves shall be 100% tested per ASME / ANSI B16.34. Valvesshall be non-firesafe design unless otherwise specified. For fire rated valves to API 607 Ed 4, sizes – 1/2” – 6”, designate Series 3 (seesection “fire rated”). To add automation and controls, see section “Automation and Controls”. PBM Model number AN(material)-(size)1L

F & AF SERIES

F-Series 5: Flush tank bottom ball valve; Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, CarbonSteel, Hastelloy C-22, or other. Weld pad shall be 316L grade stainless steel (or other) material (specify). Valve shall be three-piece“swing-out” body design. Seats and seals shall be TFM®-PTFE material and provide both upstream and downstream bubbletight sealand be adjustable for in-line wear. Stem packing shall be live loaded TFM®-PTFE material. For manual valves, handle shall be 300 seriesstainless steel. Body bolts and nuts shall be 18-8 stainless steel. Valves shall be non-firesafe design unless otherwise specified. For firerated valves to API 607 Ed 4, sizes 1/2” – 3”, designate Series 6. To add automation and controls, see last section. PBM Model number FT(material)-(size)5(end connection)

AF Series 1: Angle stem flush tank bottom ball valve. Body, ball, stem, and end fitting material shall be 316 stainless steel, Hastelloy C-276, Hastelloy C-22, or other. Weld pad shall be 316L grade stainless steel (or other) material (specify). Valve shall be two-piecedesign. Seats and seals shall be RTFE material and provide both upstream and downstream bubbletight seal and be adjustable for in-line wear. Stem packing shall be live loaded RTFE material. For manual valves, handle shall be 300 series stainless steel. Body bolts andnuts shall be 18-8 stainless steel. Valves shall be non-firesafe design unless otherwise specified. For fire rated valves to API 607 Ed 4,sizes – 1” – 6”, designate Series 3. To add automation and controls, see last section. PBM Model number AF(material)-(size)-1-(end connection)

FIRE RATED

Fire Rated 2-way Industrial, S- and F- 1/2” to 3”, AN and AF 1” to 6”. Add text: Valve design shall be tested and comply with criteriaset forth in API-607 edition 4. Valve body bolts shall be fully encapsulated. Valve design is non-Adjust-O-Seal. Body seals shall begraphite material isolated from product stream under normal operation conditions by o-ring seals. Upon sublimation of seat and seal

Industrial Valves

14

material in the event of a fire condition, a metal back up seat shall seal the valve at leakage rates in accordance with API-607 Ed. 4.Model Number: Same as above, except Series “5” Changes to “6”, Series “1” changes to “3”.

D SERIES

D-Series 5, Th re e - way diverter port ball va l ve; Body, ball, stem, and end fitting material shall be 316 stainless steel,H a s t e l l oy C-276, Hastelloy C-22, or other. Va l ve shall be three-piece design. Seats and seals shall be T F M®-PTFE materialand provide both upstream and dow n s t ream bubbletight seal and be adjustable for in-line we a r. Stem packing shall be liveloaded T F M®-PTFE material. For manual va l ves, handle shall be 300 series stainless steel. Body bolts and nuts shall be 18-8stainless steel. Maximum working pre s s u re to be 720 psig and full vacuum. Specify PBM flow pattern. To add automationand controls, see section “Automation and Controls”. PBM Model number DP(material)-(size)5(end connection) – (flow pattern)

M SERIES

M-Series 4: Three, four, or five way multi-port ball valve. Body, ball, stem, and end fitting material shall be 316 stainlesssteel, Carbon Steel, Hastelloy C-276, or other. Valve shall have 4 or 5 TFM®-PTFE Seats and seals and provide bubbletightseal and be adjustable for in-line wear. Stem packing shall be live loaded TFM®-PTFE material. For manual valves, handleshall be 300 series stainless steel. Body bolts and nuts shall be 18-8 stainless steel. Maximum working pressure to be 400psig and full vacuum. Specify PBM flow pattern for 3,4,or 5-way valve. To add automation and controls, see section“Automation and Controls”. PBM Model number MP(material)-(size)-4-(end connection)-(flow pattern)

M-Series 1: Three, four, or five way multi-port ball valve. Body, ball, stem, and end fitting material shall be (Bronze orDuctile Iron). Valve shall have 4 or 5 RTFE Seats and seals and provide bubbletight seal and be adjustable for in-line wear.Stem packing shall be live loaded RTFE material. For manual valves, handle shall be 300 series stainless steel. Body boltsand nuts shall be 18-8 stainless steel. Maximum working pressure to be 300 psig and full vacuum. Specify PBM flowpattern for 3, 4, or 5-way valve. To add automation and controls, see section “Automation and Controls”.PBM Model number MP(material)-(size)-1-(end connection)-(flow pattern)

TI SERIES

TI Series 5: Transmitter Isolation ball valveValve shall be a PBM Model “TI” Transmitter Isolation Valve (TIV), 316 stainless steel construction (body, ball,and trim),or optional Hastelloy, Titanium, 317 stainless, others) with 1.0-inch or 2-1/2-inch port diameter, with a tank side flangeto accommodate both standard ANSI 3-inch 150-lb. Flange drilling and a 25 to 27 degree offset flange pattern.Instrument side flange shall be drilled to accommodate a standard ANSI 3-inch 150-lb flange drilling. Valve shall have a1/4 turn manual lockable stainless steel handle. Valve shall have four (4) 1/4 inch NPT purge ports, each filled with a 1/4inch MNPT plug made from the same material as the valve body. Seat and seal material shall be reinforced Teflon® withVTFE o-ring. PBM Valve model TI(material)-E5L-A.For 2-1/2” port diameter, PBM Valve model TI(material)-J5L-A

AUTOMATION AND ACCESSORIES

PBM’s Direct Mount Automated Ball Valves, Valves as specified in “Manual Valves” section with addition of a “DirectMount” double acting or spring return pneumatic actuator. Actuator shall be of the double opposing piston, rack andpinion design with bidirectional pinion travel stops and hard anodized aluminum oxide body with co-depositedfluoropolymer. End caps to be polyester powder coated with 300 series stainless steel fasteners. Mounting bracket shallbe stainless steel and valve stem shall insert directly into actuator drive adapter. Actuator shall be sized utilizing a 100%safety factor. Specify supply air pressure at actuator (60 or 80 psig). PBM Model Number “PA”

PBM’s Electric actuators, limit switches, positioners, solenoids, and field bus accessories; Specify according to allstatutory and regulatory requirements. Include Nema rating requirements and electrical current.

1

Industrial Valves

Industrial Valves

A B D E F G H Approx. Weight

Size SizeCode Units

PortDia.1

Face to Fa c e CL to Fa c eCL t o

B o t t o mB- D-

Q -S- T- U

CL t oTo po f

H a n d l e

H a n d l eL e n g t hf ro m

CL

End Fitting Length E x t e n d ed

H a n d l e

B-D-Q-U-

L-Q- U-S- T-

B-D- L- Q- U-

S- T-B-D- L- U-

LengthB-, D-Length

L-Dia.

1 / 4 "

DN 8A inches 0 . 5 0 3 . 1 5 . 5 — 1 . 5 6 2 . 8 — 0 . 9 2 . 6 4 . 2 0 . 4 1 . 5 — 7 . 5 1.7 lbs. —

mm 13 79 140 — 40 70 — 23 67 1 0 5 1 0 3 8 — 1 8 9 .8 kg. —3 / 8 "

DN 10B inches 0 . 5 3 . 1 5 . 5 — 1 . 5 6 2 . 8 — 0 . 9 2 . 6 4 . 2 0 . 4 1 . 5 — 7 . 5 1.7 lbs. —

mm 13 79 140 — 40 70 — 23 67 1 0 5 1 0 3 8 — 1 8 9 .8 kg. —1 / 2 "

DN 15C inches 0 . 5 3 . 1 5 . 5 5 . 5 1 . 5 6 2 . 8 2 . 8 0 . 9 2 . 6 4 . 2 0 . 4 1 . 5 3 . 5 7 . 5 1.7 lbs. 4.0 lbs.

mm 13 79. 140 140 40 70 70 23 67 1 0 5 1 0 3 8 8 9 1 8 9 .8 kg. 1 . 8 k g .3 / 4 "

DN 20D inches 0 . 8 3 . 4 5 . 5 5 . 8 1 . 7 2 . 8 2 . 9 1 . 0 2 . 8 4 . 2 0 . 5 1 . 5 3 . 9 7 . 6 2.0 lbs. 5.2 lbs.

mm 19 87 140 146 44 70 73 2 5 71 1 0 5 1 4 3 8 9 9 1 9 3 .9 kg. 2.4 kg.1 "

DN 25E inches 1 . 0 4 . 3 6 . 0 6 . 5 2 . 1 3 . 0 3 . 3 1 . 3 3 3 . 0 5 . 1 0 . 5 1 . 5 4 . 3 7 . 6 4.5 lbs. 8.7 lbs.

mm 25 108 152 165 54 76 83 34 77 1 2 9 1 4 3 8 1 0 8 1 9 4 2.0 kg. 3.9 kg.1 - 1 / 2 "

DN 40G inches 1 . 5 5 . 5 7 . 5 8 . 0 2 . 8 4 . 0 4 . 0 1 . 7 8 4 . 1 8 . 7 0 . 5 1 . 5 5 . 0 9 . 4 10.2 lbs. 17.4 lbs.

mm 38 140 191 203 70 95 102 45 104 2 2 1 1 4 3 8 1 2 7 2 4 0 4.6 kg. 7.9 kg.2 "

DN 50H inches 2 . 0 6 . 0 8 . 0 9 . 8 3 . 0 4 . 0 4 . 9 2 . 2 4 . 4 8 . 7 0 . 7 1 . 8 6 . 0 9 . 8 15.4 lbs. 26.5 lbs.

mm 51 152 203 248 76 102 124 55 112 1 2 1 7 4 5 1 5 2 2 4 8 7.0 kg. 12.0 kg.2 - 1 / 2 "

DN 65J inches 2 . 5 8 . 0 1 1 . 5 1 1 . 5 4 . 0 5 . 8 5 . 8 2 . 8 6 . 5 1 2 . 4 0 . 7 2 . 3 7 . 0 1 1.3 36.0 lbs. 53.5 lbs.

mm 64 203 2921 292 102 146 146 71 163 3 1 6 1 8 5 9 1 7 8 2 8 8 16.3 kg. 24.3 kg.3 "

DN 80K inches 3 . 0 9 . 0 1 3 . 5 1 2 . 8 4 . 5 6 . 8 6 . 4 3. 1 6 . 7 8 1 2 . 4 0 . 7 2 . 3 7 . 5 1 1 . 7 48 lbs. 68 lbs.

mm 76 229 343 324 114 172 162 80 172 3 1 6 1 8 5 9 1 9 1 2 9 6 21.8 kg. 30.8 kg.4 "

DN 100L inches 4 . 0 1 2 . 0 1 6 . 0 1 5 . 0 6 . 0 8 . 0 7 . 5 4 . 9 7 . 3 2 4 . 4 0 . 8 2 . 3 9 . 0 C F 109 lbs. 15 7 l b s .

mm 102 305 406 381 152 203 191 125 186 6 2 1 2 1 5 9 2 2 9 C F 49.4 kg. 71 . 2 k g .6 "

DN 150M inches 6 . 0 — 2 2 . 0 2 0 . 0 — 1 1 . 0 1 0 . 0 7 . 3 *Note 3 *Note 3 C F 3 . 8 1 1 . 0 C F C F C F

mm 152 — 559 508 — 279 2 5 4 184 *Note 3 *Note 3 C F 9 5 2 7 9 C F C F C F

S-Series 5

NOT E: * L e ver Handle not recommended.

1 . Full Po r t2 . CF = Consult Fa c t o r y.3 . Gear operator is recommended if not actuated.

16

*922 Alloy Bronze Only

OptionalExtendedLocking Handle

Female NPTQ-

150#Flange

L-

Butt WeldB-D-

SocketWeld

U-

SilverBraze

S-

SolderJoint

T-

F

E

D

GBA

G

H

G

TFM® or VTFE SEAT MATERIAL

Valve Size ActuatorAir Pressure A B C D E

psig barg inches mm inches mm inches mm inches mm inches

1/4”, 3/8”,1/2”

DN 8, 10, 15

Double Acting 60, 80 4 . 1 / 5 . 5 5.5 139 2.8 71 5.4 136 1.61 40.9 1/8Spring Return 80 5.5 5.5 139 2.8 71 5.4 136 1.61 40.9 1/8Spring Return 60 4 . 1 6.4 162 3.2 81 5.8 147 1.77 45.0 1/8

3/4"DN 20

Double Acting 60, 80 4 . 1 / 5 . 5 5.5 139 2.8 71 5.6 140 1.61 40.9 1/8Spring Return 60, 80 4 . 1 / 5 . 5 6.4 162 3.2 81 6.0 151 1.77 45.0 1/8

1"DN 25

Double Acting 60, 80 4 . 1 / 5 . 5 5.5 139 2.8 71 6.2 157 1.61 40.9 1/8Spring Return 60, 80 4 . 1 / 5 . 5 8.2 207 3.7 95 7.3 184 2.1 52.6 1/8

1-1/2"DN 40

Double Acting 80 5.5 6.4 162 3.7 95 7.9 201 1.77 45.0 1/8Double Acting 60 4 . 1 8.2 207 3.7 95 8.6 217 2.1 52.6 1/8Spring Return 60, 80 4 . 1 / 5 . 5 10.7 272 4.8 123 9.5 242 2.7 68.1 1/4

2"DN 50

Double Acting 80 5.5 8.2 207 3.7 95 8.9 225 2.1 52.6 1/8Double Acting 60 4 . 1 8.2 207 3.7 95 8.9 225 2.1 52.6 1/8Spring Return 80 5.5 10.7 272 4.8 123 9.8 249 2.7 68.1 1/4Spring Return 60 4 . 1 12.9 328 5.4 137 11.0 279 2.9 72.9 1/4

2-1/2"DN 65


3"DN 80

Double Acting 60, 80 4 . 1 / 5 . 5 12.9 328 5.4 137 13.0 330 2.9 72.9 1/4Spring Return 80 5.5 14.4 367 5.8 148 13.5 342 3.2 80.0 1/4Spring Return 60 4.1 16.9 428 6.5 164 14.4 364 3.4 87.0 1/4

4"DN 100

Double Acting 60, 80 4.1, 5.5 16.9 428 6.5 164 16.5 419 3.4 87.0 1/4Spring Return 60, 80 4.1, 5.5 20.6 522 7.4 187 17.0 431 4.0 100.1 1/4

6"DN 150


S-Series 5 Actuated

Industrial Valves

17

E E

D

C

B

A

Industrial Valves

NOT E S:1 . Standard product is 316 Stainless Steel. Carbon Steel, Bronze and other materials are available upon request. Consult PBM.2 . Dimensions meet ASME Standard B16.10 long pattern.3 . Stainless Steel va l ves and Carbon Steel va l ves have raised face flanges, but are also available with flat faced flanges. Bronze va l ves have flat face flanges only.4 . D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation wo r k .5 . A gear operator is recommended for va l ves 6" and larger. Consult PBM.6 . Dimensions are for ANSI 150# Class va l ves. Consult PBM for 300# Class.

Size Units PortA B D E F G Approx.

WeightBronze

Overall Length CL to End

CL toBottom

CL to Top ofHandle

Handle Lengthfrom CL

FlangeDiameter

1/2”DN 15

inches .5 4.3 1.84 1.62 3.1 5.1 3.5 6 lbs.

mm 13 108 47 41 78 129 89 2.7 kg.

3/4”DN 20

inches .75 4.6 2.0 1.88 3.1 5.1 3.9 9 lbs.

mm 19 117 51 48 80 129 99 4.1 kg.

1”DN 25

inches 1.0 5.0 2.2 2.1 4.3 6.1 4.3 10 lbs.

mm 25 127 56 52 110 155 108 4.5 kg.

1-1/2”DN 40

inches 1.5 6.5 2.8 2.4 5.3 8.7 5.0 20 lbs.

mm 38 165 71 61 133 221 127 9.1 kg.

2”DN 50

inches 2.0 7.0 3.0 2.9 5.6 8.7 6.0 24 lbs.

mm 51 178 76 73 141 221 152 10.9 kg.

3”DN 80

inches 3.0 8.0 3.6 4.6 7.1 12.4 7.5 92 lbs.

mm 76 203 92 116 180 316 191 41.7 kg.

4”DN 100

inches 4.0 9.0 3.8 4.8 7.9 14.4 9.0 118 lbs.

mm 102 229 98 121 201 367 229 53.5 kg.

6”DN 150

inches 6.0 15.5 7.3 7.3 N/A N/A 11.0 330 lbs.

mm 153 394 186 184 N/A N/A 279 149.7 kg.

8”DN 200

inches 8.0 18.0 8.5 9.3 N/A N/A 13.5 600 lbs.

mm 203 457 216 236 N/A N/A 343 275 kg.

10”DN 250

inches 10.0 21.0 CF CF N/A N/A 16.0 CF

mm 254 533 CF CF N/A N/A 406 CF

AN Series 150# Class

18

F

E

D

GB

A

RTFE OR UHMWPE SEAT MATERIAL

Size Actuator A B C D Epsig barg inches mm inches mm inches mm inches mm inches

1/2"DN 15

Double Acting 60, 80 4.1/5.5 5.5 139 2.8 71 5.8 148 1.61 41 1/8Spring Return 60, 80 4.1/5.5 8.2 207 3.7 94 6.9 176 2.1 53 1/8

3/4"DN 20

Double Acting 60, 80 4.1/5.5 5.5 139 2.8 71 5.9 151 1.61 41 1/8Spring Return 60, 80 4.1/5.5 8.2 207 3.7 95 7.0 178 2.1 53 1/8

1”DN 25

Double Acting 60, 80 4.1/5.5 5.5 139 2.8 71 7.2 182 1.61 41 1/8Spring Return 80 5.5 8.2 207 3.7 95 8.3 210 2.1 53 1/8Spring Return 60 4.1 9.4 238 4.2 106 8.7 221 2.3 58 1/8

1-1/2"DN 40


2"DN 50


3"DN 80


4" DN 100

Double Acting 80 5.5 12.9 328 5.4 137 16.4 418 2.9 73 1/4Double Acting 60 4.1 14.4 366 5.8 148 16.9 430 3.2 80 1/4Spring Return 80 5.5 20.6 522 7.4 187 18.3 464 3.9 100 1/4Spring Return 60 4.1 22.6 575 8.6 218 20.3 515 4.3 109 1/4

6"DN 150


8"DN 200

Double Acting 80 5.5 26.5 672 11.4 290 28.5 725 5.7 145 1/4Spring Return 60 CF CF CF CF CF CF CF CF CF CFSpring Return 60, 80 5.5 26.5 672 11.4 290 28.5 725 5.7 145 1/4

AN Series ActuatedIndustrial Valves

A

B

D

CE E

19

NOT E S:* For pad thickness requirements greater than those listed, consult PBM.1 . Full Po r t2 . Gear Operator recommended.3 . CF = Consult Fa c t o r y4 . Consult factory for approximate weight of 6" va l ves with Butt Weld for Sched. 40 (B-) end fitting.5 . Male NPT, Solder Joint, Sil-Braze, Camlock, and Grooved end fittings are also ava i l a b l e .6 . B- dimensions shown meet Schedule 40. End fittings are also available to meet Schedule 10s or Schedule 5s.7 . 1/2" through 3" have 4 bolts. 4" through 8" va l ves have 8 bolts.8 . Flange holes straddle the center line, except for the 1-1/2" size.9 . D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation.

1 0 . When using optional cylindrical radius pads, pocket area may increase. Consult PBM if reduced pocket area isdesired. Note reduced pocket may decrease va l ve pressure rating.

F-Series 5Female NPT (Q-), Socket Weld (U-), Butt Weld for Sched. 40 (B-), Butt Weld for Sched. 40 (B-) 150# Flange (L-)

Industrial Valves

A B D E F G

Size Code UnitsPortDia.1

Face to Fa c e CL to Fa c e CL t oB o t t o mB - D -

Q-, U-

CL t oTo po f

H a n d l e

H a n d l eLengthfrom CL

ButtWeld

LengthPad Dia. Pad

Thickness*

Approx. Weight

Q-U-

B-D- L- Q-

U-B-D- L- B-, Q-

U- L-

1/2"

DN 15 Cinches .5 2.8 4.0 4.0 1.56 2.8 2.8 .98 2.68 4.2 1.5 2.8 0.28 2 lbs. 3 lbs.

mm 13 72 102 102 40 70 70 23 67 105 38 70 7.1 .9 kg. 1.4 kg.

3/4"

DN 20 Dinches .8 3.1 4.1 4.2 1.72 2.8 2.9 1.0 2.8 4.2 1.5 3.0 0.31 2.5 lbs. 4 lbs.

mm 19 78 104 107 44 70 73 25 71 105 38 70 7.1 1.1 kg. 1.8 kg.

1"

DN 25 Einches 1.0 3.8 4.7 5.0 2.1 3.0 3.3 1.33 3.1 5.1 1.5 3.8 0.32 5 lbs. 7 lbs.

mm 25 98 120 126 54 76 83 34 78 129 38 95 8.1 2.3 kg. 3.2 kg.

1-1/2"

DN 40 Ginches 1.5 5.1 6.1 6.3 2.8 3.8 4.0 1.78 4.4 8.7 1.5 5.5 0.46 13 lbs. 16 lbs.

mm 38 129 154 161 70 95 102 45 111 221 38 140 11.7 5.9 kg. 7.3 kg.

2"

DN 50 Hinches 2.0 5.7 6.7 7.6 3.0 4.0 4.9 2.2 4.7 8.7 1.75 6.5 0.49 19 lbs. 25 lbs.

mm 51 144 169 192 76 102 124 55 119 221 45 165 12.4 8.6 kg. 11.3 kg.

3"

DN 80 Kinches 3.0 8.4 10.6 10.3 4.5 6.8 6.4 3.1 6.8 12.4 2.3 9.0 0.77 57 lbs. 68 lbs.

mm 76 213 270 261 114 172 162 80 174 315 59 229 19.6 25.9 kg. 30.8 kg.

4"

DN 100 Linches 4.0 10.8 12.8 12.3 6.0 8.0 7.5 4.9 7.3 24.1 2.3 11.5 0.90 120 lbs. 133 lbs.

mm 102 275 325 313 152 203 191 125 186 611 59 292 22.9 54.4 kg. 60.3 kg.

6"

DN 150 Minches 6.0 — 17.8 16.8 — 11.0 10.0 7.2 Note 2 CF 3.8 17.0 1.23 CF CF

mm 154 — 452 427 — 279 254 182 Note 2 CF 95 432 31.2 CF CF

AB

G

F

E

D

I

H

Female NPTQ-

150#Flange

L-

Butt Weld

B-D-

SocketWeld

U-

Industrial Valves

TFM® OR VTFE SEAT MATERIAL

Size Actuator Type Air Supply A B C D E F

p s i g b a r g inches mm inches mm inches mm inches mm inches inches mm

1/2"DN 15

Double Acting 60, 80 4 . 1 / 5 . 5 5.5 139 2.8 71 5.4 136 1.61 41 1/8 0.09 2.3Spring Return 80 5 . 5 5.5 139 2.8 71 5.4 136 1.61 41 1/8 0.09 2.3Spring Return 60 4 . 1 6.4 162 3.2 81 5.8 147 1.77 45 1/8 -0.13 -3.3

3/4"DN 20

Double Acting 60, 80 4 . 1 / 5 . 5 5.5 139 2.8 71 5.5 140 1.61 41 1/8 0.17 4.3Spring Return 60, 80 4 . 1 / 5 . 5 6.4 162 3.2 81 6.0 151 1.77 46 1/8 -0.05 - 1 . 2 7

1"DN 25

Double Acting 60, 80 4 . 1 / 5 . 5 5.5 139 2.8 71 6.2 156 1.61 41 1/8 0.53 13.5Spring Return 60, 80 4 . 1 / 5 . 5 8.2 207 3.7 95 7.3 184 2.1 53 1/8 0.06 1.5

1-1/2"DN 40

Double Acting 80 5 . 5 6.4 162 3.2 81 7.9 200 1.77 45 1/8 0.92 23.4Double Acting 60 4 . 1 8.2 207 3.7 95 8.6 217 2.1 53 1/8 0.67 17.0Spring Return 60, 80 4 . 1 / 5 . 5 10.7 272 4.8 123 9.5 241 2.7 68 1/4 0.15 3.8

2"DN 50

Double Acting 60, 80 4 . 1 / 5 . 5 8.2 207 3.7 95 8.9 225 2.1 53 1/8 1.01 25.7Spring Return 80 5 . 5 10.7 272 4.8 123 9.8 249 2.7 68 1/4 0.49 12.5Spring Return 60 4 . 1 12.9 328 5.4 137 11.0 279 2.9 73 1/4 0.14 3.6

3"DN 80

Double Acting 60, 80 4 . 1 / 5 . 5 12.9 328 5.4 137 13.0 330 2.9 73 1/4 1.36 34.5Spring Return 80 5 . 5 14.4 366 5.8 148 13.5 342 3.2 80 1/4 1.20 30.5Spring Return 60 4 . 1 16.9 428 6.5 164 14.4 364 3.4 87 1/4 0.85 22

4"DN 100

Double Acting 60, 80 4 . 1 / 5 . 5 16.9 428 6.5 164 14.4 364 3.4 87 1/4 1.78 45Spring Return 60, 80 4 . 1 / 5 . 5 20.6 522 7.4 187 17.0 431 3.9 100 1/4 1.38 35.1

6"DN150

Double Acting 60, 80 4 . 1 / 5 . 5 22.6 575 8.6 218 22.6 574 4.3 109 1/4 2.51 63.8Spring Return 80 5 . 5 22.6 575 8.6 218 22.6 574 4.3 109 1/4 2.51 63.8Spring Return 60 4 . 1 26.5 672 11.4 290 26.2 666 5.7 145 1/4 1.09 27.7

F-Series 5 Actuated

21

A

B

E

F

E

D

C

Industrial Valves

B C D H I

Size Units PortFace-to-Face CL to End

PadDiameter

PadThicknessQ-, B-, U- L- Q-, B-, U- L-

1”DN 25

i n ch e s 1 . 0 3.6 4 . 1 1 . 9 2.5 3.7 .31m m 2 5 91 1 0 4 4 8 64 94 7.9

1-1/2”DN 40

i n ch e s 1 . 5 5.0 5.5 2.7 3.3 5.5 .56m m 3 8 127 140 69 84 139.7 14.2

2”DN 50

i n ch e s 2 . 0 5.5 6.2 2.9 3.5 7.0 .69m m 5 1 140 158 74 89 177.8 17.5

3”DN 80

inches 2.8 8.4 9.2 4.3 5.1 10 .75mm 70 213 234 109 130 254. 19.1

4”DN 100

inches 3.5 9.5 1 0 . 5 5.2 6.2 11.5 .75mm 89 241 2 6 7 132 158 292 19.1

6”DN 150

inches 5.3 1 2 . 1 * 15.6 6.6* 10.1 15 .75mm 133 3 0 7 396 168 257 381 19.1

8”DN 200

inches 8 N / A 18 N / A 9.8 18.5 1.25mm 2 0 0 N / A 460 N / A 250 470 32

AF-Series 1

22

1”, 1-1/2”, & 8” = 10º2”, 3”, 4”, & 6” = 15º

Q- = Female NPT OutletU- = Socket Weld OutletL- = 150# ANSI Flange Outlet

H

C

< degrees

I D

*Buttweld end; Q and U not available in 6” size.

AF-Series 1 ActuatedRTFE or UHMWPE Seats

Size Actuator TypeAir supply Port A B C D NPT Air

Inletpsig barg inches mm inches mm inches mm inches mm inches mm inches

1"DN 25

Double Acting 80 5.5

1.00 25.4

5.5 139 2.8 71 1.12 28 6.2 158 1/8Double Acting 60 4.1 6.4 162 3.2 81 0.93 24 6.7 169 1/8Spring Return 80 5.5 8.2 207 3.7 95 0.73 19 7.3 186 1/8Spring Return 60 4.1 9.4 238 4.2 106 0.55 14 7.8 197 1/8

1-1/2"DN 40

Double Acting 60, 80 4.1, 5.51.50 38.1

8.2 207 3.7 95 1.55 39 8.4 212 1/8Spring Return 80 5.5 10.7 272 4.8 123 1.10 28 9.3 237 1/4Spring Return 60 4.1 12.9 328 5.4 137 0.84 21 10.5 267 1/4

2"DN 50

Double Acting 60, 80 4.1, 5.52.00 5 0 . 8


3"DN 80

Double Acting 60, 80 4.1, 5.52.75 69.9

12.9 328 5.4 137 3.9 100 13.2 334 1/4Spring Return 80 5.5 14.4 367 5.8 148 3.8 98 13.6 345 1/4Spring Return 60 4.1 16.9 4 3 0 6.5 164 3.7 95 14.5 367 1/4

4"DN 100

Double Acting 60, 80 4.1, 5.53.50 88.9

12.9 328 5.4 137 4.3 109 13.6 346 1/4Spring Return 60 4.1 16.9 4 3 0 6.5 164 4.1 104 24.9 633 1/4Spring Return 80 5.5 20.6 522 7.4 187 3.7 94 15.4 391 1/4

6"DN 150

Double Acting 60, 80 4.1, 5.55.25 133.4


Industrial Valves

23

AB

C

D

Female NPT (Q-), Socket weld (U-), butt Weld for Schedule 40 (B-), 150# Flange (L-)

Size SizeCode

U n i t sPo r tD i a .

A B C D E G ApproximateWeightFace-to-Face CL to Face

H a n d l eL e n g t hf rom CL

CL toTop ofHandle

CL to Bottom Entry End Fitting

Q-U-

B-D-

L-Q-U-

B-D-

L-Q-U-

B-D-

Length

L-Dia.

U-Length

B-D-

Length

L-Dia.

Q-, U-B-, D-

L-

1 / 2 "DN 15

Ci n ch e s 0 . 5 0 3 . 1 5 . 5 5 . 5 1 . 6 2 . 8 2 . 8 4 . 2 2 . 6 1 . 6 2 . 8 2 . 8 0 . 5 1 . 5 3 . 5 2 lbs. 5.2 lbs.

m m 1 2 . 7 7 9 1 4 0 1 4 0 4 1 7 1 7 1 . 1 0 7 6 6 4 1 7 1 7 1 1 3 3 8 8 9 .9 kg. 2.4 kg.

3 / 4 "DN 20

Di n ch e s 0 . 7 5 3 . 4 5 . 5 5 . 8 1 . 7 2 . 8 2 . 9 4 . 2 2 . 8 1 . 7 2 . 8 2 . 9 0 . 6 1 . 5 4 . 0 2.5 lbs. 7 lbs.

m m 1 9 . 1 8 6 1 4 0 1 4 7 4 3 7 1 7 4 1 0 7 7 1 4 3 7 1 7 4 1 5 3 8 1 0 2 1.1 kg. 3.2 kg.

1 "DN 25

Ei n ch e s 1 . 0 4 . 3 6 . 0 6 . 5 2 . 1 3 . 0 3 . 3 5 . 1 3 . 0 2 . 1 3 . 0 3 . 3 0 . 5 1 . 5 4 . 3 5 lbs. 11 lbs.

m m 2 5 1 0 9 1 5 2 1 6 5 5 3 7 6 8 4 1 3 0 7 6 5 3 7 6 8 4 1 3 3 8 1 0 9 2.3 kg. 5.0 kg.

1 - 1 / 2 "DN 40

Gi n ch e s 1 . 5 5 . 5 7 . 5 8 . 0 2 . 8 3 . 8 4 . 0 8 . 7 4 . 1 2 . 8 3 . 8 4 . 0 0 . 5 1 . 5 5 . 0 11.5 lbs.21.5 lbs.

m m 3 8 1 4 0 1 9 1 2 0 3 7 1 9 7 1 0 2 2 2 1 1 0 4 7 1 9 7 1 0 2 1 3 3 8 1 2 7 5.2 kg. 9.8 kg.

2 "DN 50

Hi n ch e s 2 . 0 6 . 0 8 . 0 9 . 8 3 . 0 4 . 0 4 . 9 8 . 7 4 . 4 3 . 0 4 . 0 4 . 9 0 . 7 1 . 8 6 . 0 16.5 lbs. 33 lbs.

m m 5 1 1 5 2 2 0 3 2 4 9 7 6 1 0 2 1 2 5 2 2 1 1 1 2 7 6 1 0 2 1 2 5 1 8 4 6 1 5 2 7.5 kg. 15.0 kg.

3 "DN 80

Ki n ch e s 3 . 0 9 . 0 1 3 . 5 1 2 . 9 4 . 5 6 . 8 6 . 4 1 2 . 4 6 . 8 4 . 5 6 . 8 6 . 4 0 . 7 2 . 3 7 . 5 50 lbs. 80 lbs.

m m 7 6 2 2 9 3 4 3 3 2 8 1 1 4 1 7 3 1 6 3 3 1 5 1 7 3 1 1 4 1 7 3 1 6 3 1 8 5 8 1 9 1 22.7 kg. 36.3 kg.

4 "DN 100

Li n ch e s 4 . 0 1 2 . 0 1 6 . 0 1 5 . 0 6 . 0 8 . 0 7 . 5 2 4 . 4 7 . 3 6 . 0 8 . 0 7 . 5 0 . 8 2 . 3 9 . 0 123 lbs. 155 lbs.

m m 1 0 2 3 0 5 4 0 6 3 8 1 1 5 2 2 0 3 1 9 1 6 2 0 1 8 5 1 5 2 2 0 3 1 9 1 2 0 5 8 2 2 9 55.8 kg. 70.3 kg.

6 "DN 150

Mi n ch e s 6 . 0 C F 2 2 . 0 2 0 . 0 C F 1 1 . 0 1 0 . 0 Note 1 Note 1 9 . 0 1 1 . 0 1 0 . 0 C F 3 . 8 1 1 . 0 C F C F

m m 1 5 2 . 4 C F 5 5 9 5 0 8 C F 2 7 9 2 5 4 Note 1 Note 1 2 2 9 2 7 9 2 5 4 C F 9 7 2 7 9 C F C F

N o t e s :1 . Gear operator is recommended.2 . Other end fittings are also available. See page 16 and 18.3 . Other flanged end fittings are available upon special request.4 . Butt Weld ends are also available in Schedule 10s & Schedule 5s.5 . 1/2" – 3" size va l ves have 4 bolts. 4" and 6" sizes have 8 bolts.6 . D rawings are for illustration purposes only.7 . Using a welded connection on the common port of a DP va l ve may complicate maintenance. Provisions must be made to allow removal of end fittings and body

from the line. PBM recommends Female NPT (Q-) or flanged end fittings for common port connection for ease of va l ve maintenance.

Industrial Valves D-Series 5

24

Refer to Page 12 for Flow Pattern Options

AB

G

G G

C

D

E

B

150#Flange

L-

Butt WeldB-D-

SocketWeld

U-

Female NPTQ-

Industrial Valves

TFM® or VTFE SEAT MATERIAL

Size Actuator TypeAir Supply A B C D E


1/2"DN 15

Double Acting 60, 80 4.1, 5.5 5.5 139 2.8 71 5.4 136 1.61 41 1/8Spring Return 80 5 . 5 5.5 139 2.8 71 5.4 136 1.61 41 1/8Spring Return 60 4.1 6.4 162 3.2 81 5.8 147 1.77 45 1/8

3/4"DN 20

Double Acting 60, 80 4.1, 5.5 5.4 139 2.8 71 5.5 140 1.61 41 1/8Spring Return 60, 80 4.1, 5.5 6.4 162 3.2 81 6.0 151 1.77 45 1/8

1"DN 25


1-1/2"DN 40

Double Acting 80 5 . 5 6.4 162 3.2 81 7.9 201 1.77 45 1/8Double Acting 60 4.1 8.2 207 3.7 95 8.6 217 2.1 53 1/8Spring Return 60, 80 4.1, 5.5 10.7 271 4.8 123 9.5 242 2.7 68 1/4

2"DN 50

Double Acting 80 5 . 5 8.2 207 3.7 95 8.9 225 2.1 53 1/8Double Acting 60 4.1 8.2 207 3.7 95 8.9 225 2.1 53 1/8Spring Return 80 5 . 5 10.7 271 4.8 123 9.8 249 2.7 68 1/4Spring Return 60 4.1 12.9 328 5.4 137 11.0 279 2.9 73 1/4

3"DN 80


4"DN 100


6"DN 150


D-Series 5 Actuated

25

A

B

C

E

D

E

M-Series 4A B C1 D1 C2 D2 E F G1 G2 H I

Size SizeCode Units

PortDia.

Face to Fa c e CL to Fa c e Face to Fa c e CL to Fa c e H a n d l eL e n g t hf rom CL

CL toTop ofHandle

CL toBottom

SideEntry

CL toBottomBottomEntry

U -D i a .

L-Dia.

A p p rox .Weight

S/SQ/U-

B- L- Q/U-B- L- Q/U-

B- L- Q/U-B- L-

1 / 2 "DN 15 C

i n ch e s . 5 0 4 . 5 C F 2 . 3 C F 4 . 5 C F 2 . 3 C F 6 . 1 2 . 8 1 . 5 C F . 9 3 . 5 7 lbs.m m 1 3 1 1 4 C F 5 8 C F 1 1 4 C F 5 8 C F 1 5 5 7 1 3 8 C F 2 3 8 9 3.2 kg.

3 / 4 "DN 20 D

i n ch e s . 7 5 4 . 5 C F 2 . 3 C F 4 . 5 C F 2 . 3 C F 6 . 1 2 . 8 1 . 5 C F 1 . 0 3 . 9 7 lbs.m m 1 9 1 1 4 C F 5 8 C F 1 1 4 C F 5 8 C F 1 5 5 7 1 3 8 C F 2 5 9 9 3.2 kg.

1 "DN 25 E

i n ch e s 1 . 0 4 . 7 7 . 3 2 . 3 3 . 6 4 . 7 5 . 7 2 . 3 3 . 6 8 . 1 5 . 0 1 . 6 2 . 3 1 . 3 4 . 3 12 lbs.m m 2 5 1 1 9 1 8 5 5 8 9 1 1 1 9 1 4 5 5 8 9 1 2 0 6 1 2 7 4 1 5 8 3 3 1 0 9 5.4 kg.

1 - 1 / 4 "DN 32 F

i n ch e s 1 . 0 4 . 7 C F 2 . 3 C F 4 . 7 C F 2 . 3 C F 8 . 1 5 . 0 1 . 6 2 . 4 1 . 7 4 . 6 12 lbs.m m 2 5 1 1 9 C F 5 8 C F 1 1 9 C F 5 8 C F 2 0 6 1 2 7 4 1 6 1 4 3 1 1 7 5.4 kg.

1 - 1 / 2 "DN 40 G

i n ch e s 1 . 5 6 . 6 1 0 . 6 3 . 3 5 . 3 6 . 6 8 . 6 3 . 3 5 . 3 1 2 . 1 5 . 3 2 . 3 3 . 3 1 . 9 5 . 0 31 lbs.m m 3 8 1 6 8 2 6 9 8 4 1 3 5 1 6 8 2 1 8 8 4 1 3 5 3 0 7 1 3 5 5 8 8 4 4 8 1 2 7 14.1 kg.

2 "DN 50 H

i n ch e s 2 . 0 7 . 8 1 1 . 9 3 . 9 6 . 0 7 . 6 9 . 7 3 . 9 6 . 0 1 2 . 1 5 . 8 2 . 6 3 . 9 2 . 4 6 . 0 47 lbs.m m 5 1 1 9 8 3 0 2 9 9 1 5 2 1 9 3 2 4 6 9 9 1 5 2 3 0 7 1 4 7 6 6 9 9 6 1 1 5 2 21.3 kg.

3 ”DN 80 K

i n ch e s 3 . 0 1 1 . 7 1 6 . 5 5 . 8 8 . 2 1 1 . 1 1 3 . 5 5 . 8 8 . 2 Consult PBM 3 . 9 5 . 8 3 . 5 7 . 5 133 lbs.m m 7 6 2 9 7 4 1 9 1 4 7 2 0 8 2 8 2 3 4 3 1 4 7 2 0 8 9 9 1 4 7 8 9 1 9 1 60.3 kg.

4 ”DN 100 L

i n ch e s 4 . 0 1 5 . 4 1 9 . 3 7 . 7 9 . 6 1 4 . 2 1 6 . 2 7 . 7 9 . 6 Consult PBM 4 . 9 7 . 7 4 . 6 9 . 0 254 lbs.m m 1 0 2 3 9 1 4 9 0 1 9 6 2 4 4 3 6 1 4 1 2 1 9 6 2 4 4 1 2 5 1 9 6 1 1 7 2 2 9 1 1 5 . 2 k g.

6 ”DN 150 M

i n ch e s 6 . 0 1 6 . 5 2 1 . 5 8 . 5 1 2 . 0 1 9 . 9 2 4 . 0 1 0 . 0 1 2 . 0 Consult PBM 9 . 5 1 0 . 0 6 . 7 1 1 . 0 400 lbs.m m 1 5 2 4 1 9 5 4 6 2 1 6 3 0 5 5 0 6 6 1 0 2 5 4 3 0 5 2 4 1 2 5 4 1 7 0 2 7 9 181.4 kg.

-NOT E S:1 . Using a welded connection for more than one end fitting on an MP Series va l ve may complicate maintenance. Provisions must be made to allow removal of end

fittings and body from the line.2 . C avity fillers in 1/2" – 4" sizes are installed from the top. Cavity fillers in 6" size are installed from the sides.3 . 1-1/4" and double angle port are not full-port design.4 . A gear operator is recommended for 3", 4", and 6" va l ves. Consult PBM.5 . D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation wo r k .6 . Approximate weights are for 3-way, side entry, angle port MP Series 4 va l ves, with female NPT end fittings.7 . Q and U ends not available in 6” size.

Industrial Valves

26

150#Flange

L-

ButtWeld

B-

SocketWeld

U-Female NPT

Q-

Refer to Page 12-13 for Flow Pattern Options

B

IG2

F

E

D1D2

G1

C1

H

C2

VTFE OR TFM® SEAT MATERIAL

Size Actuator TypeAir supply A B C D E


1/2"DN 15

Double Acting 80 5.5 5.5 139 2.8 71.1 6.8 171 1.61 41 1/8Double Acting 60 4.1 6.4 162 3.2 80.5 7.2 182 1.77 45 1/8Spring Return 80 5.5 8.2 207 3.7 94.5 7.8 199 2.1 53 1/8Spring Return 60 4.1 9.4 238 4.2 105.9 8.3 210 2.3 58 1/8

3/4"DN 20

Double Acting 80 5.5 5.5 139 2.8 71.1 6.7 171 1.61 41 1/8Double Acting 60 4.1 6.4 162 3.2 80.5 7.2 183 1.77 45 1/8Spring Return 80 5.5 8.2 207 3.7 94.5 7.8 199 2.1 53 1/8Spring Return 60 4.1 9.4 238 4.2 106 8.3 210 2.3 58 1/8

1"DN 25

Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 94.5 8.7 220 2.1 53 1/8Spring Return 80 5.5 10.7 272 4.8 123 9.6 244 2.7 68 1/4Spring Return 60 4.1 12.9 328 5.4 137 10.8 274 2.9 73 1/4

1-1/4"DN 32

Double Acting 60, 80 4.1, 5.5 8.2 207 3.7 94.5 8.7 220 2.1 53 1/8Spring Return 80 5.5 10.7 272 4.8 123 9.6 244 2.7 68 1/4Spring Return 60 4.1 12.9 328 5.4 137 10.8 274 2.9 73 1/4

1-1/2"DN 40

Double Acting 60, 80 4.1, 5.5 12.9 328 5.4 137 12.1 308 2.9 73 1/4Spring Return 80 5.5 14.4 366 5.8 148 12.6 320 3.2 80 1/4Spring Return 60 4.1 16.9 428 6.5 164 15.2 387 3.4 87 1/4

2"DN 50


3"DN 80


4"DN 100


6"DN 150


M-Series 4 ActuatedIndustrial Valves

27

A

B

C

E

D

E

S i z eS i z eC o d e

U n i t s

B C1 D1 C2 D2 E F G1 G2 H IA p p rox .We i g h tB ro n z e

Po r tD i a .

Face to Fa c e CL to Fa c e Face to Fa c e CL to Fa c e H a n d l eL e n g t hf rom CL

CL toTop ofHandle

CL toBottom

SideEntry

CL toBottomBottomEntry

R -D i a .

L -D i a .

Q - / S L - Q - / S L - Q - / S L - Q - / S L -

1 / 2 "DN 15

Ci n ch e s . 6 2 4 . 0 C F 2 . 0 C F 4 . 0 C F 2 . 0 C F 6 . 1 2 . 8 1 . 5 C F . 9 3 . 5 17 lbs.m m 1 6 1 0 2 C F 5 1 C F 1 0 2 C F 5 1 C F 1 5 5 7 1 3 8 C F 2 3 8 9 7.7 kg.

3 / 4 "DN 20

Di n ch e s . 7 5 4 . 0 C F 2 . 0 C F 4 . 0 C F 2 . 0 C F 6 . 1 2 . 8 1 . 5 C F 1 . 0 3 . 9 17 lbs.m m 1 9 6 1 0 2 C F 5 1 C F 1 0 2 C F 5 1 C F 1 5 5 7 1 3 8 C F 2 5 9 9 7.7 kg.

1 "DN 25

Ei n ch e s 1 . 0 4 . 7 7 . 3 2 . 3 3 . 6 4 . 5 5 . 7 2 . 4 3 . 6 8 . 1 5 . 0 1 . 6 2 . 3 1 . 3 4 . 3 22 lbs.m m 2 5 1 1 9 1 8 5 5 8 9 1 1 1 4 1 4 5 6 1 9 1 2 0 6 1 2 7 4 1 5 8 3 3 1 0 9 10.0 kg.

1 - 1 / 4 "DN 32

Fi n ch e s 1 . 0 4 . 8 C F 2 . 4 C F 4 . 5 C F 2 . 4 C F 8 . 1 5 . 0 1 . 6 2 . 4 1 . 7 4 . 6 23 lbs.m m 2 5 1 2 2 C F 6 1 C F 1 1 4 C F 6 1 C F 2 0 6 1 2 7 4 1 6 1 4 3 1 1 7 10.4 kg.

1 - 1 / 2 "DN 40

Gi n ch e s 1 . 5 6 . 6 1 0 . 6 3 . 3 5 . 3 6 . 0 8 . 6 3 . 3 5 . 3 1 2 . 1 5 . 3 2 . 3 3 . 3 1 . 9 5 . 0 47 lbs.m m 3 8 1 6 8 2 6 9 8 4 1 3 5 1 5 2 2 1 8 8 4 1 3 5 3 0 7 1 3 5 5 8 8 4 4 8 1 2 7 21.3 kg.

2 "DN 50

Hi n ch e s 2 . 0 7 . 8 1 1 . 9 3 . 9 6 . 0 7 . 6 9 . 7 3 . 9 5 . 9 1 2 . 1 5 . 8 2 . 6 3 . 9 2 . 4 6 . 0 70 lbs.m m 5 1 1 9 8 3 0 2 9 9 1 5 2 1 9 3 2 4 6 9 9 1 5 0 3 0 7 1 4 7 6 6 9 9 6 1 1 5 2 31.8 kg.

3 "DN 80

Ki n ch e s 2 . 3 1 1 . 0 1 4 . 6 5 . 5 7 . 3 9 . 6 1 1 . 4 5 . 5 7 . 3 1 2 . 1 6 . 7 4 . 1 5 . 5 3 . 5 7 . 5 107 lbs.m m 5 7 2 7 9 3 7 1 1 4 0 1 8 5 2 4 4 2 9 0 1 4 0 1 8 5 3 0 7 1 7 0 1 0 4 1 4 0 8 9 1 9 1 48.5 kg.

4 "DN 100

Li n ch e s 3 . 0 C F 1 7 . 0 C F 8 . 5 C F 1 4 . 0 C F 8 . 5 1 4 . 1 8 . 8 5 . 6 C F C F 9 . 0 235 lbs.m m 7 6 C F 4 3 2 C F 2 1 6 C F 3 5 6 C F 2 1 6 3 5 8 2 2 4 1 4 2 C F C F 2 2 9 107 kg.

N o t e s :1 . Iron va l ves have raised face flanges. Bronze va l ves have flat face flanges.2 . D rawings are for illustration purposes only. Consult PBM prior to any fabrication or installation wo r k .3 . Using a brazed or soldered connection for more than one end fitting on an MP Series va l ve may complicate maintenance. Provisions must be made to allow removal of

end fittings and body from line.4 . Approximate weights are estimated based on va l ves with 150# Flange end fittings.

Industrial ValvesM-Series 1

28

L- S-(Bronze Only)

Female NPTQ-

Refer to Page 12-13 for Flow Pattern Options

C1

B G2

F

E

D2

G1

D1

HI

C2

VTFE OR TFM® SEAT MATERIAL

Size Actuator TypeAir Supply A B C D E


1/2"DN 15


3/4"DN 20

Double Acting 80 5.5 5.5 139 2.8 71 7.5 189 1.61 41 1/8Double Acting 60 4.1 6.4 162 3.2 81 7.9 200 1.8 45 1/8Spring Return 80 5.5 8.2 207 3.7 95 8.5 217 2.1 53 1/8Spring Return 60 4.1 9. 238 4.2 106 9.0 228 2.3 58 1/8

1"DN 25


1-1/4"DN 32


1-1/2"DN 40


2"DN 50


3"DN 80


4"DN 100


M-Series 1 Actuated

Industrial Valves

29

A

B

C

E E

D

Sizes:• 1", 2", 2-1/2", 3"Materials:• 316 & 317L S/S• Ti t a n i u m• H a s t e l l oy• O t h e r sOptions:• Milled Ball Flats• Po l i s h i n g

Obtain accurate transmitter readings and replace leaky knife gate valves with PBM’s TransmitterIsolation Valve. Ideal for Pulp & Paper and Chemical applications. 2-Way ball valve features minimal dead space and positive shut-off. Calibration Port, CIP Port,150# Flange, and Locking Handle standard.

Industrial Valves Transmitter Isolation Valves

1” TIV

2-1/2” TIV

3 0Tank Bottom

Transmitter

TransmitterValve

Studs fromTank Padto Valve

5/8”-11 x 2-1/4” LG. Hex Boltor 3-1/4” LG. All Thread Stud

for Transmitter to Valve

3” 150#Flange

3” 150#Flange

Studsfrom

Tank Padto Valve

5/8”-11 x 2-1/4” LG. Hex Boltor 3-1/4” LG. All Thread Stud

for Transmitter to Valve

Transmitter

• Easy 1/4-turn operation

• 1/2”, 3/4” sizes, API 607 Edition 5 qualified

• Class 2500#

• Manufactured from wrought or forged material

• Rod-out capability

• Variety of end connections

• Variety of body materials

• Variety of seat and seal materials

• Optional Ceramic Balls & Seats (Zirconia TTZ)

• Welded tamperproof body design

• Visual position indication

• Lockable handles available

• Unique applications welcome

root valvesgauge valves

isolation valvesdrain valves

Isolation for:n Transmitter pressure measurementn Flush ringsn Flow measurementn Pressure gaugesn Orifice plates

Features

Instrument Valves

Applications

Industrial Valves

31

Can be mounted on2-1/8” centers

Fabflex Manifolds are space-saving pipe and valveconfigurations designed to accommodate special industrialand sanitary applications. Can be shipped in lengths up to18’, with multiple manual and automated valves pre-installed. 100% testing before shipment ensures properperformance. Minimal dead space reduces areas wheremedia could become trapped. Blank valve pads can beprovided to accommodate future process expansion.

Valve Sizes:• 1/4" - 6"

M a t e r i a l s :• 316 & 316L S/S• Carbon Steel• H a s t e l l o y

O p t i o n s :• F i re - Te s t• C I P / S I P• Cavity Fillers• A c t u a t i o n• S t e a m• Polishing & E l e c t ro p o l i s h i n g

Fabflex Manifold Assemblies

Industrial Valves

32

Sample process media quickly and easily with PBM’sSampling Valve. Special pad design minimizes dead space.Easy CIP with Purge Ports and Milled Ball Flats ensuresreliable samples. Valve can be shipped pre-mounted topiping for easy installation. Ideal for heavy duty andsanitary applications.Manual valves standard.

S i z e s :• 1/2" - 2"

M a t e r i a l s :• 316 &

316L S/S• H a s t e l l o y• T i t a n i u m• O t h e rs

O p t i o n s :• A c t u a t i o n• S t e a m• Po l i s h i n g

Sampling ValvesControl ValvesUse PBM’s 2-Way Control Valves in industrial andsanitary throttling or shearing applications to accuratelycontrol the flow of liquids or thick media. These valvesfeature characterized balls with various port shapes,including "V." Manual valve standard.

S i z e s :• 1/2" - 6"

M a t e r i a l s :• 316 & 316L S/S• H a s t e l l o y• O t h e rs

O p t i o n s :• A c t u a t i o n• 30°, 45°, 60° V Angles• S l o t t e d• Locking Handle• Polishing & E l e c t ro p o l i s h i n g

Industrial Valves

33

Rising Stem Sampling Valve

• 316L S/S• Swickle or Hose Barb Outlet• 1/4” Bore Diameter• L a rge Nylon Knob• T h readed Inlet (1/4”, 3/8”)• Autoclavable or To rc h a b l e• Replaceable EPDM O-Ring and

T F M® S e a t• Po l i s h i n g

Piston guide

Die cast aluminu mend cap s, p o lyester p owder coat e d

N e s t e dspring sets

A s s e m bly screwStainless Steel

S e a l sNBR Standard

B o dy manu fa c t u red from ex t ruded aluminum UNI 6060,H a rd coat anodize d

N i cke l - p l at e dSteel pinion

S t a n d a rdVi s u a lPo s i t i o nI n d i c at o r

• Operating Pressure Range - 40 psig to 120 psig (2.8 barg to 8 barg)

• Temperature Range: -4ºF to 185ºF (-20ºC to 85ºC)

• Rotation Adjustment: + or - 5º• Namur Pinion and Solenoid Valve Mounting• Bottom of Pinion according to ISO 5211 -

DIN 3337

Automation and Controls

34

Pistons made from die cast aluminu m

Piston guide

Actuator Model

Air Pressure at Actuator ApproximateWeight

60 psig 4.1 barg 80 psig 5.5 bargConstant Torque Output

in-lbs. N-m in-lbs. N-m lbs. kg.PAVBL453D--0052 133 1 5 179 20 2.3 1.0PAVBL453D--0063 238 27 321 36 3.3 1.5PAVBL453D--0075 435 49 586 66 5.5 2.5PAVBL453D--0085 629 71 851 96 7 3PAVBL453D--0100 991 112 1,336 151 11 5PAVBL453D--0115 1,640 185 2,210 250 18 8PAVBL453D--0125 2,157 244 2,906 328 22 10PAVBL453D--0140 3,013 340 4,018 454 34 15PAVBL453D--0160 4,394 497 5,859 662 43 20PAVBL453D--0200 8,239 931 10,981 1,241 71 32PAVBL453D--0270 19,097 2,158 25,469 2,878 154 70

Actuator ModelSpring

Set

Spring TorqueOutput

Air Pressure at ActuatorApproximate

Weight 60 psig/4.1 barg 80 psig/5.5 barg

Torque Output from PressureStart Start End End Start Start End End Start Start End End

in-lbs. N-m in-lbs. N-m in-lbs. N-m in-lbs. N-m in-lbs. N-m in-lbs. N-m lbs. kg.PAVBL253S- -0052 03 66 7.5 38 4.3 80 9.0 47 5.3 N/A N/A N/A N/A 2.7 1.2PAVBL453S- -0052 05 88 10 60 7 N/A N/A N/A N/A 101 11.4 55 6 2.7 1.2PAVBL253S- -0063 03 128 15 71 8 149 17 79 9 N/A N/A N/A N/A 4.0 2PAVBL453S- -0063 05 196 22 111 13 N/A N/A N/A N/A 193 22 95 11 4.0 2PAVBL253S- -0075 03 234 26 125 14 275 31 137 16 N/A N/A N/A N/A 6.9 3PAVBL453S- -0075 05 358 40 193 22 N/A N / A N/A N/A 354 4 0 157 18 6.9 3PAVBL253S- -0085 03 307 35 183 21 387 44 211 24 N/A N/A N/A N/A 9.4 4PAVBL453S- -0085 05 456 52 273 31 N/A N/A N/A N/A 503 57 257 29 9.4 4PAVBL253S- -0100 03 495 56 279 32 628 71.0 329 37 N/A N/A N/A N/A 14.4 7PAVBL453S- -0100 05 733 83 417 47 N/A N / A N/A N/A 802 91 378 43 14.4 7PAVBL253S- -0115 03 786 89 442 50 1,044 118 541 61 N/A N/A N/A N/A 24 11PAVBL453S- -0115 05 1,176 133 657 74 N/A N/A N/A N/A 1,352 153 637 72 24 11PAVBL253S- -0125 03 969 110 530 60 1,351 153 640 72 N/A N/A N/A N/A 27 12PAVBL453S- -0125 05 1,412 1 6 0 779 88 N/A N/A N/A N/A 1,762 199 789 8 9 27 12PAVBL453S- -0140 03 1 ,617 1 8 3 853 96 1,910 216 856 97 N/A N/A N/A N/A 45 21PAVBL453S- -0140 05 2,251 254 1,200 136 N/A N/A N/A N/A 2,481 280 1,017 115 45 21PAVBL253S- -0160 04 2,443 276 1,522 1 7 2 2,447 277 1,350 153 N/A N/A N/A N/A 65 30PAVBL453S- -0160 05 2,860 3 2 3 1,917 217 N/A N/A N/A N/A 3,452 390 2,240 253 65 30PAVBL253S- -0200 04 4,040 457 2,686 304 4,788 5 4 1 3,080 348 N/A N/A N/A N/A 111 50PAVBL453S- -0200 06 5,900 667 4,009 453 N/A N/A N/A N/A 5,893 666 3,539 400 111 50PAVBL253S- -0270 05 10,788 1 , 2 1 9 6,915 781 11,495 1 , 2 9 9 6,884 778 N/A N/A N/A N/A 193 88PAVBL453S- -0270 08 14,400 1 , 6 2 7 9,230 1,043 N/A N/A N/A N/A 15,360 1,735 9,220 1,042 193 88

Features:

• Compact spool valve with threaded port direct mounts to actuator.

• All exhaust ports are pipeable, providing better protection against harsh environments.

• Standard manual override

• DIN, watertight and explosion-proof solenoids available

• Single and dual coil solenoid constructions

• Mountable in any position

Postioners Electric Actuators

Position Indicators

Automation and Controls

Solenoids

• 4-20 mA• 3-15 psi• Nema 4, 7

• Nema 4, 7

Options:• Nema 4, 7• Mechanical Switches• Proximity• Fieldbus• DeviceNet• Visual Indication• AS-i

35

PBM, Inc. • 1070 Sandy Hill Road, Irwin, PA 15642Phone: 800.967.4PBM • 724.863.0550 • Fax: 724.864.9255E-mail: [email protected] • Web: www.pbmvalve.com LT- 31 5/08

PBM, Inc.

United States • Canada • Australia • Mexico • Brazil • Chile • UAEUnited Kingdom • Germany • Sweden • Spain • Belgium • France

Ireland • Switzerland • Austria • The Netherlands India • Taiwan • China • Thailand • Singapore

Visit PBM online atwww.pbmvalve.com

to find the PBM domestic or international representative near you.

INDUSTRIAL VALVES - ERAMCO · n PBM valves provide bidirectional upstream sealing. n Valve body...

Documents

Transcript of INDUSTRIAL VALVES - ERAMCO · n PBM valves provide bidirectional upstream sealing. n Valve body...