Induction Hardening - Wikipedia, The Free Encyclopedia
Transcript of Induction Hardening - Wikipedia, The Free Encyclopedia
-
7/29/2019 Induction Hardening - Wikipedia, The Free Encyclopedia
1/6
I nduct ionhardenin g - W ikipedia, thef r eeencyclopedia
org/wiki/Induction_hardening
Induction hardeningFrom Wikipedia, the free encyclopedia
Induction hardening is a form of heat treatment in which a metal part is heated by induction heating and then
quenched. The quenched metal undergoes a martensitic transformation, increasing the hardness and brittleness of
the part. Induction hardening is used to selectively harden areas of a part or assembly without affecting the
properties of the part as a whole.[1]
Contents
1 Process
1.1 Definition
1.2 History
1.3 Principal methods
1.3.1 Single shot hardening
1.3.2 Traverse hardening
1.4 Equipment
1.4.1 Power required
1.4.2 Frequency
2 See also
3 References
3.1 Notes
3.2 Bibliography
4 External links
Process
Induction heating is a non contact heating process which utilises the principle of electromagnetic induction to
produce heat inside the surface layer of a work-piece. By placing a conductive material into a strong alternating
magnetic field, electrical current can be made to flow in the material thereby creating heat due to the I2R losses in
the material. In magnetic materials, further heat is generated below the curie point due to hysteresis losses. The
current generated flows predominantly in the surface layer, the depth of this layer being dictated by the frequency o
the alternating field, the surface power density, the permeability of the material, the heat time and the diameter of thbar or material thickness. By quenching this heated layer in water, oil or a polymer based quench the surface layer
is altered to form a martensitic structure which is harder than the base metal. [2]
Definition
A widely used process for the surface hardening of steel. The components are heated by means of an alternating
magnetic field to a temperature within or above the transformation range followed by immediate quenching. The
core of the component remains unaffected by the treatment and its physical properties are those of the bar from
which it was machined, whilst the hardness of the case can be within the range 37/58 HRC. Carbon and alloy stee
http://en.wikipedia.org/wiki/Surface_hardeninghttp://en.wikipedia.org/wiki/Martensitichttp://en.wikipedia.org/wiki/Induction_hardening#External_linkshttp://en.wikipedia.org/wiki/Induction_hardening#Noteshttp://en.wikipedia.org/wiki/Induction_hardening#Equipmenthttp://en.wikipedia.org/wiki/Induction_hardening#Traverse_hardeninghttp://en.wikipedia.org/wiki/Induction_hardening#Single_shot_hardeninghttp://en.wikipedia.org/wiki/Induction_hardening#Principal_methodshttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev39-1http://en.wikipedia.org/wiki/Quenchedhttp://en.wikipedia.org/wiki/Martensitic_transformationhttp://en.wikipedia.org/wiki/Hardness_(materials_science)http://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev39-1http://en.wikipedia.org/wiki/Carbonhttp://en.wikipedia.org/wiki/Rockwell_scalehttp://en.wikipedia.org/wiki/Surface_hardeninghttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev58-2http://en.wikipedia.org/wiki/Martensitichttp://en.wikipedia.org/wiki/Polymerhttp://en.wikipedia.org/wiki/Quenchinghttp://en.wikipedia.org/wiki/Permeability_(electromagnetism)http://en.wikipedia.org/wiki/Hysteresishttp://en.wikipedia.org/wiki/Curie_pointhttp://en.wikipedia.org/wiki/Magnetic_fieldhttp://en.wikipedia.org/wiki/Conductivehttp://en.wikipedia.org/wiki/Electromagnetismhttp://en.wikipedia.org/wiki/Induction_hardening#External_linkshttp://en.wikipedia.org/wiki/Induction_hardening#Bibliographyhttp://en.wikipedia.org/wiki/Induction_hardening#Noteshttp://en.wikipedia.org/wiki/Induction_hardening#Referenceshttp://en.wikipedia.org/wiki/Induction_hardening#See_alsohttp://en.wikipedia.org/wiki/Induction_hardening#Frequencyhttp://en.wikipedia.org/wiki/Induction_hardening#Power_requiredhttp://en.wikipedia.org/wiki/Induction_hardening#Equipmenthttp://en.wikipedia.org/wiki/Induction_hardening#Traverse_hardeninghttp://en.wikipedia.org/wiki/Induction_hardening#Single_shot_hardeninghttp://en.wikipedia.org/wiki/Induction_hardening#Principal_methodshttp://en.wikipedia.org/wiki/Induction_hardening#Historyhttp://en.wikipedia.org/wiki/Induction_hardening#Definitionhttp://en.wikipedia.org/wiki/Induction_hardening#Processhttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev39-1http://en.wikipedia.org/wiki/Hardness_(materials_science)http://en.wikipedia.org/wiki/Martensitic_transformationhttp://en.wikipedia.org/wiki/Quenchedhttp://en.wikipedia.org/wiki/Induction_heatinghttp://en.wikipedia.org/wiki/Heat_treatment -
7/29/2019 Induction Hardening - Wikipedia, The Free Encyclopedia
2/6
I nduct ionhardenin g - W ikipedia, thef r eeencyclopedia
org/wiki/Induction_hardening
with an equivalent carbon content in the range 0.40/0.45% are most suitable for this process. [1]
A source of high frequency electricity is used to drive a large alternating current through a coil. The passage of
current through this coil generates a very intense and rapidly changing magnetic field in the space within the work
coil. The workpiece to be heated is placed within this intense alternating magnetic field where eddy currents are
generated within the workpiece and resistance leads to Joule heating of the metal.
This operation is most commonly used in steel alloys. Many mechanical parts, such as shafts, gears, and springs, a
subjected to surface treatments, before the delivering, in order to improve wear behavior. The effectiveness of thetreatments depends both on surface materials properties modification and on the introduction of residual stress.
Among these treatments, induction hardening is one of the most widely employed to improve component durability
It determines in the work-piece a tough core with tensile residual stresses and a hard surface layer with
compressive stress, which have proved to be very effective in extending the component fatigue life and wear
resistance.[3]
Induction surface hardened low alloyed medium carbon steels are widely used for critical automotive and machine
applications which require high wear resistance. Wear resistance behavior of induction hardened parts depends on
hardening depth and the magnitude and distribution of residual compressive stress in the surface layer.[2]
History
The basis of all induction heating systems was discovered in 1831 by Michael Faraday. Faraday proved that by
winding two coils of wire around a common magnetic core it was possible to create a momentary electromotive
force in the second winding by switching the electric current in the first winding on and off. He further observed tha
if the current was kept constant, no EMF was induced in the second winding and that this current flowed in
opposite directions subject to whether the current was increasing or decreasing in the circuit.[4]
Faraday concluded that an electric current can be produced by a changing magnetic field. As there was no physic
connection between the primary and secondary windings, the emf in the secondary coil was said to be inducedan
so Faraday's law of induction was born. Once discovered, these principles were employed over the next century o
so in the design of dynamos (electrical generators and electric motors, which are variants of the same thing) and in
forms of electrical transformers. In these applications, any heat generated in either the electrical or magnetic circuit
was felt to be undesirable. Engineers went to great lengths and used laminated cores and other methods to minimis
the effects.[4]
Early last century the principles were explored as a means to melt steel, and the motor generator was developed to
provide the power required for the induction furnace. After general acceptance of the methodology for melting
steel, engineers began to explore other possibilities for the utilisation of the process. It was already understood tha
the depth of current penetration in steel was a function of its magnetic permeability, resistivity and the frequency ofthe applied field. Engineers at Midvale Steel and The Ohio Crankshaft Company drew on this knowledge to
develop the first surface hardening induction heating systems using motor generators.[5]
The need for rapid easily automated systems led to massive advances in the understanding and utilisation of the
induction hardening process and by the late 1950s many systems utilising motor generators and thermionic emissio
triode oscillators were in regular use in a vast array of industries. Modern day induction heating units utilise the late
in semiconductor technology and digital control systems to develop a range of powers from 1 kW to many
megawatts.
http://en.wikipedia.org/wiki/Megawattshttp://en.wikipedia.org/wiki/Triodehttp://en.wikipedia.org/wiki/Thermionic_emissionhttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-5http://en.wikipedia.org/wiki/Midvale_Steelhttp://en.wikipedia.org/wiki/Induction_furnacehttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev1-4http://en.wikipedia.org/wiki/Laminatedhttp://en.wikipedia.org/wiki/Transformerhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Dynamohttp://en.wikipedia.org/wiki/Faraday%27s_law_of_inductionhttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev1-4http://en.wikipedia.org/wiki/Electric_currenthttp://en.wikipedia.org/wiki/Electromotive_forcehttp://en.wikipedia.org/wiki/Michael_Faradayhttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev58-2http://en.wikipedia.org/wiki/Induction_hardening#cite_note-3http://en.wikipedia.org/wiki/Wear_resistancehttp://en.wikipedia.org/wiki/Fatigue_(material)http://en.wikipedia.org/wiki/Compressive_stresshttp://en.wiktionary.org/wiki/durabilityhttp://en.wikipedia.org/wiki/Residual_stresshttp://en.wikipedia.org/wiki/Joule_heatinghttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-rudnev39-1http://en.wikipedia.org/wiki/Equivalent_carbon_content -
7/29/2019 Induction Hardening - Wikipedia, The Free Encyclopedia
3/6
I nduct ionhardenin g - W ikipedia, thef r eeencyclopedia
org/wiki/Induction_hardening
Principal methods
Single shot hardening
In single shot systems the component is held statically or rotated in the coil and the whole area to be treated is
heated simultaneously for a pre-set time followed by either a flood quench or a drop quench system. Single shot is
often used in cases where no other method will achieve the desired result for example for flat face hardening of
hammers, edge hardening complex shaped tools or the production of small gears.[6]
In the case of shaft hardening a further advantage of the single shot methodology is the production time compared
with progressive traverse hardening methods. In addition the ability to use coils which can create longitudinal curre
flow in the component rather than diametric flow can be an advantage with certain complex geometry.
There are disadvantages with the single shot approach. The coil design can be an extremely complex and involved
process. Often the use of ferrite or laminated loading materials is required to influence the magnetic field
concentrations in given areas thereby to refine the heat pattern produced. Another drawback is that much more
power is required due to the increased surface area being heated compared with a traverse approach.[7]
Traverse hardening
In traverse hardening systems the work piece is passed through the induction coil progressively and a following
quench spray or ring is utilised. Traverse hardening is used extensively in the production of shaft type components
such as axle shafts, excavator bucket pins, steering components, power tool shafts and drive shafts. The compone
is fed through a ring type inductor which normally features a single turn. The width of the turn is dictated by the
traverse speed, the available power and frequency of the generator. This creates a moving band of heat which whe
quenched creates the hardened surface layer. The quench ring can be either integral a following arrangement or a
combination of both subject to the requirements of the application. By varying speed and power it is possible to
create a shaft which is hardened along its whole length or just in specific areas and also to harden shafts with stepsin diameter or splines. It is normal when hardening round shafts to rotate the part during the process to ensure any
variations due to concentricity of the coil and the component are removed.
Traverse methods also feature in the production of edge components, such as paper knives, leather knives,
lawnmower bottom blades, and hacksaw blades. These types of application normally utilise a hairpin coil or a
transverse flux coil which sits over the edge of the component. The component is progressed through the coil and a
following spray quench consisting of nozzles or drilled blocks.
Many methods are used to provide the progressive movement through the coil and both vertical and horizontal
systems are used. These normally employ a digital encoder and programmable logic controller for the positionalcontrol, switching, monitoring, and setting. In all cases the speed of traverse needs to be closely controlled and
consistent as variation in speed will have an effect on the depth of hardness and the hardness value achieved.
Equipment
Power required
Power supplies for induction hardening vary in power from a few kilowatts to hundreds of kilowatts dependent of
the size of the component to be heated and the production method employed i.e. single shot hardening, traverse
http://en.wikipedia.org/wiki/Programmable_logic_controllerhttp://en.wikipedia.org/wiki/Encoderhttp://en.wikipedia.org/wiki/Digitalhttp://en.wikipedia.org/wiki/Concentricityhttp://en.wikipedia.org/wiki/Induction_coilhttp://en.wikipedia.org/wiki/Induction_hardening#cite_note-7http://en.wikipedia.org/wiki/Ferrite_(magnet)http://en.wikipedia.org/wiki/Induction_hardening#cite_note-6 -
7/29/2019 Induction Hardening - Wikipedia, The Free Encyclopedia
4/6
I nduct ionhardenin g - W ikipedia, thef r eeencyclopedia
org/wiki/Induction_hardening
hardening or submerged hardening.
In order to select the correct power supply it is first necessary to calculate the surface area of the component to be
heated. Once this has been established then a variety of methods can be used to calculate the power density
required, heat time and generator operating frequency. Traditionally this was done using a series of graphs, comple
empirical calculations and experience. Modern techniques typically utilise finite element analysis and Computer-
aided manufacturing techniques, however as with all such methods a thorough working knowledge of the induction
heating process is still required.
For single shot applications the total area to be heated needs to be calculated. In the case of traverse hardening the
circumference of the component is multiplied by the face width of the coil. Care must be exercised when selecting
coil face width that it is practical to construct the coil of the chosen width and that it will live at the power required
for the application.
Frequency
Induction heating systems for hardening are available in a variety of different operating frequencies typically from
1 kHz to 400 kHz. Higher and lower frequencies are available but typically these will be used for specialist
applications. The relationship between operating frequency and current penetration depth and therefore hardness
depth is inversely proportional. i.e. the lower the frequency the deeper the case.
Examples of frequencies for various case depths and
material diameters
Case depth [mm] Bar diameter [mm] Frequency [kHz]
0.8 to 1.5 5 to 25 200 to 400
1.5 to 3.010 to 50 10 to 100
>50 3 to 10
3.0 to 10.0
20 to 50 3 to 10
50 to 100 1 to 3
>100 1
The above table is purely illustrative, good results can be obtained outside these ranges by balancing power
densities, frequency and other practical considerations including cost which may influence the final selection, heat
time and coil width. As well as the power density and frequency, the time the material is heated for will influence th
depth to which the heat will flow by conduction. The time in the coil can be influenced by the traverse speed and th
coil width, however this will also have an effect on the overall power requirement or the equipment throughput.
It can be seen from the above table that the selection of the correct equipment for any application can be extremel
complex as more than one combination of power, frequency and speed can be used for a given result. However in
practice many selections are immediately obvious based on previous experience and practicality.
See also
Case hardening
Induction forging
http://en.wikipedia.org/wiki/Induction_forginghttp://en.wikipedia.org/wiki/Case_hardeninghttp://en.wikipedia.org/wiki/Computer-aided_manufacturinghttp://en.wikipedia.org/wiki/Finite_element_analysishttp://en.wikipedia.org/wiki/Empirical -
7/29/2019 Induction Hardening - Wikipedia, The Free Encyclopedia
5/6
I nduct ionhardenin g - W ikipedia, thef r eeencyclopedia
org/wiki/Induction_hardening
Induction heater
Induction shrink fitting
References
Notes
1. ^ ab Rudnev et al. 2002, p. 39
2. ^ ab Rudnev et al. 2002, p. 58
3. ^ Rudnev et al. 2002, p. 59
4. ^ ab Rudnev et al. 2002, p. 1
5. ^ Rudnev et al. 2002, p. 2
6. ^ Rudnev et al. 2002, p. 249
7. ^ Rudnev et al. 2002, p. 250
Bibliography
Davies, John; Simpson, Peter (1979),Induction Heating Handbook(http://books.google.com/?
id=rOBSAAAAMAAJ) , McGraw-Hill, ISBN 0-07-084515-8, http://books.google.com/?
id=rOBSAAAAMAAJ.
Rapoport, Edgar; Pleshivtseva, Yulia (2006), Optimal Control of Induction Heating Processes
(http://books.google.com/?id=0ARyAB-avewC) , CRC Press, ISBN 0-8493-3754-2,
http://books.google.com/?id=0ARyAB-avewC.
Rudnev, Valery; Loveless, Don; Cook, Raymond; Black, Micah (2002),Handbook of Induction Heating
(http://books.google.com/?id=FRmqNkwTvGAC) , CRC Press, ISBN 0-8247-0848-2,
http://books.google.com/?id=FRmqNkwTvGAC.
External links
Frequently Asked Questions About The Induction Hardening Process with examples of Induction Heating
Applications (http://www.inductionheating.co.uk/induction-heating-faqs.html)
The National Metals Centre offering Design, Modeling & Simulation (DMS) technologies relating to
Induction Hardening processes - NAMTEC (http://www.namtec.co.uk)
Retrieved from "http://en.wikipedia.org/w/index.php?title=Induction_hardening&oldid=528034922"
Categories: Metal heat treatments
Navigation menu
This page was last modified on 26 December 2012 at 02:50.
Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply.
See Terms of Use for details.
Wikipedia is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.
http://www.wikimediafoundation.org/http://wikimediafoundation.org/wiki/Terms_of_Usehttp://en.wikipedia.org/wiki/Wikipedia:Text_of_Creative_Commons_Attribution-ShareAlike_3.0_Unported_Licensehttp://en.wikipedia.org/wiki/Special:Categorieshttp://en.wikipedia.org/w/index.php?title=Induction_hardening&oldid=528034922http://www.namtec.co.uk/http://www.inductionheating.co.uk/induction-heating-faqs.htmlhttp://books.google.com/?id=FRmqNkwTvGAChttp://en.wikipedia.org/wiki/Special:BookSources/0-8247-0848-2http://en.wikipedia.org/wiki/International_Standard_Book_Numberhttp://books.google.com/?id=FRmqNkwTvGAChttp://books.google.com/?id=0ARyAB-avewChttp://en.wikipedia.org/wiki/Special:BookSources/0-8493-3754-2http://en.wikipedia.org/wiki/International_Standard_Book_Numberhttp://books.google.com/?id=0ARyAB-avewChttp://books.google.com/?id=rOBSAAAAMAAJhttp://en.wikipedia.org/wiki/Special:BookSources/0-07-084515-8http://en.wikipedia.org/wiki/International_Standard_Book_Numberhttp://books.google.com/?id=rOBSAAAAMAAJhttp://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-7http://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-6http://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-5http://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-rudnev1_4-1http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-rudnev1_4-0http://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-3http://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-rudnev58_2-1http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-rudnev58_2-0http://en.wikipedia.org/wiki/Induction_hardening#CITEREFRudnevLovelessCookBlack2002http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-rudnev39_1-1http://en.wikipedia.org/wiki/Induction_hardening#cite_ref-rudnev39_1-0http://en.wikipedia.org/wiki/Induction_shrink_fittinghttp://en.wikipedia.org/wiki/Induction_heaterhttp://en.wikipedia.org/wiki/Category:Metal_heat_treatments -
7/29/2019 Induction Hardening - Wikipedia, The Free Encyclopedia
6/6
I nduct ionhardenin g - W ikipedia, thef r eeencyclopedia
org/wiki/Induction_hardening