Important Fluvial Terms Drainage basin/catchment/watershed: defined by the ridges that control the...
-
date post
20-Dec-2015 -
Category
Documents
-
view
220 -
download
5
Transcript of Important Fluvial Terms Drainage basin/catchment/watershed: defined by the ridges that control the...
Important Fluvial Terms
Drainage basin/catchment/watershed:•defined by the ridges that control the direction of precipitation drainage. Every stream has a drainage basin. •A drainage basin collects water, which is delivered to a larger basin, creating larger streams
Continental Divide: •The line separating subcontinental-scale drainage basinsWater and sediment usually terminate in oceans
Internal drainage basins are areas in which water does not terminate in an ocean. (leaves via evaporation or subsurface gravitational drainage
http://atlas.gc.ca/site/english/maps/freshwater/distribution/drainage
Drainage Basins
Red: selected drainage basins for firstorder streams(collection ofred areas shouldfill the yellow area but somestreams notrepresented)
Yellow:larger drainage basins for river
Drainage density is determined by dividing the total length of all streams by the area of the basin
For a given surface, a higher drainage density is generallyfound in a humid area than in a dry area
Drainage Pattern is the arrangement of channels in an area. Drainage pattern is determined by:
•Slope of the catchment•Rock resistance to weathering•Climate•Underlying bedrock•Subsurface hydrology
Drainage Patterns
1. DendriticTree-like pattern [Fig. 11-6 (a)]Efficient –branch length minimized
2. RectangularA faulted and jointed landscape directs streamsalong right angle turns [Fig. 11-6 (e)]
3. TrellisForms where resistance of bedrock varies or along a folded landscapeFolds create parallel large streams, capturing runoff from smaller streams and joining into larger rivers at right angles [Fig. 11-6 (b)]
4. Radial DrainageStreams flow from central peak or dome
5. Annular DrainageOccurs in dome structures with concentric patterns of rock strata
6. Parallel drainage [Fig. 11-6 (e)]Steep slopes - similar to dendritic, but steep slopes cause branches to appear almost parallel to one another
7. Deranged DrainageIn areas with disrupted surface patterns there is often no clear drainage geometry(common in glaciated areas)
Flow velocity: A measure of how fast a stream moves downstream (v in m/s). It depends on thedischarge, slope, size and shape of the channel.
Discharge: The amount of water flowing througha cross section of a stream (Q in m3/s). Fluctuates seasonally and diurnally (eg. melting greatest in spring/summer and during the day) Q=wdv
Capacity: The amount of sediment that can be carried by a stream (m3/s or kg/s). Capacityincreases with discharge.
Competence: The maximum particle size that canbe carried by the stream (related to flow velocity)
Sedimentary load is the total amount of sediment carriedby a stream. Sedimentary load is carried by bedload, suspended load and washload.
Bedload: Coarse particles (eg. sand) which have high settling velocity. Sediments are transported near the streambed, kept loose by turbulence and particle interaction.
Suspended load: Particles are in the water column, sortedby weight (larger particles near the bottom). The higherthe discharge, the higher the suspended load.
Washload: Fine particles with low settling velocity, whichtravel at the same speed as the flow. Almost independent ofdischarge.
Solution load: The total amount of dissolved ions transported by a stream. Determined by nature of source material and the physical and chemical characteristics of the stream.
Sediment bulking: Sediment is added to a stream in excess of its capacity.
In normal, turbulent flow, the critical point of the dynamic equilibrium between erosion and deposition is exceeded with sediment addition, thus, deposition (aggradation) occurs.
Aggradation may lead to the development of a braidedstream.
Braided stream, S. AlaskaPhoto: M. Miller (U. Oregon)
Reynolds Number (R):R = inertial forces_____ = lv
internal frictional forces
where = fluid densityl = flow depthv = overall mean velocity = viscosity of the fluid
Flow Regimes: Understanding of different flow regimes helps us to understandresulting sediment bedforms and structures.
Laminar flow: Quasi-laminar flow occurs in slow moving(R<500) streams with smooth bottoms. Frictional
forces exceed inertial forces (500<R<2000)Turbulent flow: Higher flow velocity and bed roughness, with(R>2000) eddies. Friction with bed reduces v. Velocity
constant with depth except basal laminar layer.
A. Laminar flow
B. Quasi-laminar flow
C. Turbulent flow
D. Obstruction in turbulent flow
Relative velocity profiles
Flow Regimes
2. Froude Number (F):
F = inertial force = v gravitational force (gl)-2
The ratio between the average velocity of the entire liquid massand the rate of downflow wave migration (celerity).
F<1 Inertial forces are less than gravitational forces. Therefore,celerity of surface waves exceeds stream velocity (ie., waveforms faster than river, and break downstream)
F=1 Critical flow (no whitewater)
F>1 Main body of water moves faster than surface waves. Surface waves break upstream.
Turbulent flow
A. Subcritical (waves break downstream)
B. Critical (standing waves at water surface)
C. Supercritical (waves break upstream)
CELERITYFLOW VELOCITY
Quasi-laminar flow:Sand ripples with ripple cross-lamination form, unless the sandis very coarse.
Turbulent, subcritical flow:Sand dunes showing cross-beds in section form
Turbulent, critical flow:Horizontal beds with plane laminations and minute strings of particles aligned parallel to flow direction at surface
Turbulent, supercritical flow:Poorly-developed dunes or other massive beds form with steeper side facing upstream
How can we tell which type of flow was occurring by looking ata cross section ? In the following slides, we will look at the sediment facies resulting from (a) meandering streams, (b) decelerating streams and (c) shallow streams with highly variablewater and sediment discharge.
Meandering streams
Streams take on a sinuous form where slope is shallow.Water flows faster around the bends. The varying currentcauses distinct erosional and depositional surfaces
1. Outer bend Erosional, supercritical flows- undercut bank
2. Middle-outer Deposition of coarse-grainedor parallel, laminated sand(critical flow)
3. Middle-inner Depositional, subcritical flowCross-bedded sand dunes
4. Inner bend Fine-grained, cross-laminatedsand ripples (point bars located here)
As the meander bend migrates, the lateral sedimentary facies stackvertically. In other words, as the bend increases, coarse-grainedmaterial becomes covered with progressively finer-grained sediment.
Meandering Stream
As this stream meanders, the bend seen in cross-section A extends further to the left. As this occurs, there is a transition from erosional,supercritical flows to critical and subcritical flow, with the associated depositional features superimposed as in cross-section B.
*Note: Plane beds and antidunes are onlyformed when flows are charged to capacity.
Bar Formation
A. In high-competence flows in shallow streams with variable water and sediment discharge, coarse grained sediment formsupstream from finer-grained sediment (sheet bar).
Such bars are parallel to current with no flow separation bubble (B)
C. Finer-grained sediment tends to form transverse bars of variousshapes and do contain inclined depositional surfaces downstream (D)
Bar formation
Hydraulic conditionschange during floods, eroding bars to formScours
Coarser material is deposited during the highflow, with progressivelysmaller particles depositedthereafter
New bars form and finer sediment is again foundabove the gravel, resultingin cut and fills
Cut and fills
Oxbow lake
A lake that was formerly a channel of a meandering stream
Formed when a meandering stream erodes back upon itself, straightening the main channel. The old river channelis still filled with water until sedimentation fills it again
Oxbow Lake,Milk River, MT (just south of Canadian border)
Stream gradientA stream usually has a steeper slope upstream and a gentler slope downstream, resulting in an uneven, concaveshape
NickpointA nickpoint is the location at which an abrupt change instream gradient occurs
WaterfallAt a nickpoint, the water falls to softer, more easily erosive rock strata, leading to undercutting
Floodplains
Flat, low-lying areas near a river that are repeatedly flooded.Rivers overflow during high flow and deposit sediment upon the floodplain.
Rivers of a floodplain are generally embedded within the sediment of the floodplain itself.
Levees develop along the banks of rivers as a result of flooding. When a river floods, the velocity is reducedbeyond the bank, leading to sedimentation. The larger particles fall first, leading to the creation of a natural levee. The river may rise relative to the floodplain, leading to backswamp areas.
Terraces
Uplift may allow a stream to cut deeper into its ownfloodplain (rejuvenation), leading to alluvial terraces. Such terraces look like steps above the river (Fig. 11-19)
River DeltasThe velocity of a river rapidly decelerates as it reaches a large body of water. This leads to deposition, of progressively smaller particles (large ones first). A characteristic triangular shape forms (hence the term delta)
The river channels divide into smaller ones in all the sediment, leading to what appears to be a reversed dendritic drainage pattern (braided delta).
Nile River Delta