IM952 - Lincoln Electric
Transcript of IM952 - Lincoln Electric
OPERATOR’S MANUAL
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © Lincoln Global Inc.
AutoDrive 4R90IM952-A
March, 2010
For use with machines having Code Number : 11492, 11722
Safety Depends on YouLincoln arc welding and cuttingequipment is designed and built withsafety in mind. However, your overallsafety can be increased by properinstallation ... and thoughtful opera-t ion on your part. DO NOTINSTALL, OPERATE OR REPAIRTHIS EQUIPMENT WITHOUTREADING THIS MANUAL ANDTHE SAFETY PRECAUTIONSCONTAINED THROUGHOUT. And,most importantly, think before youact and be careful.
FOR ENGINEpowered equipment.
1.a. Turn the engine off before troubleshooting and maintenancework unless the maintenance work requires it to be running.
____________________________________________________1.b.Operate engines in open, well-ventilated
areas or vent the engine exhaust fumesoutdoors.
____________________________________________________1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.Stop the engine and allow it to cool beforerefueling to prevent spilled fuel from vaporiz-ing on contact with hot engine parts andigniting. Do not spill fuel when filling tank. Iffuel is spilled, wipe it up and do not startengine until fumes have been eliminated.
____________________________________________________1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing andtools away from V-belts, gears, fans and all other movingparts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safetyguards to perform required maintenance. Removeguards only when necessary and replace them when themaintenance requiring their removal is complete.Always use the greatest care when working near movingparts.
___________________________________________________1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor oridler by pushing on the throttle control rodswhile the engine is running.
___________________________________________________1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenancework, disconnect the spark plug wires, distributor cap ormagneto wire as appropriate.
iSAFETYi
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that youpurchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is availablefrom the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES AREPERFORMED ONLY BY QUALIFIED INDIVIDUALS.
WARNING
Mar ‘95
ELECTRIC ANDMAGNETIC FIELDSmay be dangerous
2.a. Electric current flowing through any conductor causeslocalized Electric and Magnetic Fields (EMF). Weldingcurrent creates EMF fields around welding cables andwelding machines
2.b. EMF fields may interfere with some pacemakers, andwelders having a pacemaker should consult their physicianbefore welding.
2.c. Exposure to EMF fields in welding may have other healtheffects which are now not known.
2.d. All welders should use the following procedures in order tominimize exposure to EMF fields from the welding circuit:
2.d.1. Route the electrode and work cables together - Securethem with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode andwork cables. If the electrode cable is on your rightside, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close aspossible to the area being welded.
2.d.5. Do not work next to welding power source.
1.h. To avoid scalding, do not remove theradiator pressure cap when the engine ishot.
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituentsare known to the State of California to cause can-cer, birth defects, and other reproductive harm.
The engine exhaust from this product containschemicals known to the State of California to causecancer, birth defects, or other reproductive harm.
The Above For Diesel Engines The Above For Gasoline Engines
iiSAFETYii
ARC RAYS can burn.4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks andthe rays of the arc when welding or observingopen arc welding. Headshield and filter lensshould conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistantmaterial to protect your skin and that of your helpers fromthe arc rays.
4.c. Protect other nearby personnel with suitable, non-flammablescreening and/or warn them not to watch the arc nor exposethemselves to the arc rays or to hot spatter or metal.
ELECTRIC SHOCK cankill.3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.Do not touch these “hot” parts with your bareskin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.Make certain the insulation is large enough to cover your fullarea of physical contact with work and ground.
In addition to the normal safety precautions, if weldingmust be performed under electrically hazardousconditions (in damp locations or while wearing wetclothing; on metal structures such as floors, gratings orscaffolds; when in cramped positions such as sitting,kneeling or lying, if there is a high risk of unavoidable oraccidental contact with the workpiece or ground) usethe following equipment:• Semiautomatic DC Constant Voltage (Wire) Welder.• DC Manual (Stick) Welder.• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,electrode reel, welding head, nozzle or semiautomaticwelding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electricalconnection with the metal being welded. The connectionshould be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable andwelding machine in good, safe operating condition. Replacedamaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts ofelectrode holders connected to two welders because voltagebetween the two can be the total of the open circuit voltageof both welders.
3.i. When working above floor level, use a safety belt to protectyourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
FUMES AND GASEScan be dangerous.5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing thesefumes and gases. When welding, keepyour head out of the fume. Use enoughventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. Whenwelding with electrodes which require specialventilation such as stainless or hard facing (seeinstructions on container or MSDS) or on lead orcadmium plated steel and other metals or coatingswhich produce highly toxic fumes, keep exposure aslow as possible and within applicable OSHA PEL andACGIH TLV limits using local exhaust or mechanicalventilation. In confined spaces or in some circum-stances, outdoors, a respirator may be required.Additional precautions are also required when weldingon galvanized steel.
5. b. The operation of welding fume control equipment is affectedby various factors including proper use and positioning ofthe equipment, maintenance of the equipment and the spe-cific welding procedure and application involved. Workerexposure level should be checked upon installation andperiodically thereafter to be certain it is within applicableOSHA PEL and ACGIH TLV limits.
5.c. Do not weld in locations near chlorinated hydrocarbon vaporscoming from degreasing, cleaning or spraying operations.The heat and rays of the arc can react with solvent vapors toform phosgene, a highly toxic gas, and other irritating prod-ucts.
5.d. Shielding gases used for arc welding can displace air andcause injury or death. Always use enough ventilation,especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for thisequipment and the consumables to be used, including thematerial safety data sheet (MSDS) and follow youremployer’s safety practices. MSDS forms are available fromyour welding distributor or from the manufacturer.
5.f. Also see item 1.b.
Jan ‘09
iiiSAFETYiii
FOR ELECTRICALLYpowered equipment.
8.a. Turn off input power using the disconnectswitch at the fuse box before working onthe equipment.
8.b. Install equipment in accordance with the U.S. NationalElectrical Code, all local codes and the manufacturer’srecommendations.
8.c. Ground the equipment in accordance with the U.S. NationalElectrical Code and the manufacturer’s recommendations.
CYLINDER may explodeif damaged.7.a. Use only compressed gas cylinders
containing the correct shielding gas for theprocess used and properly operatingregulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable forthe application and maintained in good condition.
7.b. Always keep cylinders in an upright position securelychained to an undercarriage or fixed support.
7.c. Cylinders should be located:•Away from areas where they may be struck or subjected tophysical damage.
•A safe distance from arc welding or cutting operations andany other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any otherelectrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outletwhen opening the cylinder valve.
7.f. Valve protection caps should always be in place and handtight except when the cylinder is in use or connected foruse.
7.g. Read and follow the instructions on compressed gascylinders, associated equipment, and CGA publication P-l,“Precautions for Safe Handling of Compressed Gases inCylinders,” available from the Compressed Gas Association1235 Jefferson Davis Highway, Arlington, VA 22202.
WELDING and CUTTINGSPARKS cancause fire or explosion.6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to preventthe welding sparks from starting a fire.
Remember that welding sparks and hotmaterials from welding can easily go through small cracksand openings to adjacent areas. Avoid welding nearhydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,special precautions should be used to prevent hazardoussituations. Refer to “Safety in Welding and Cutting” (ANSIStandard Z49.1) and the operating information for theequipment being used.
6.c. When not welding, make certain no part of the electrodecircuit is touching the work or ground. Accidental contactcan cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until theproper steps have been taken to insure that such procedureswill not cause flammable or toxic vapors from substancesinside. They can cause an explosion even though they havebeen “cleaned”. For information, purchase “RecommendedSafe Practices for the Preparation for Welding and Cutting ofContainers and Piping That Have Held HazardousSubstances”, AWS F4.1 from the American Welding Society(see address above).
6.e. Vent hollow castings or containers before heating, cutting orwelding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oilfree protective garments such as leather gloves, heavy shirt,cuffless trousers, high shoes and a cap over your hair. Wearear plugs when welding out of position or in confined places.Always wear safety glasses with side shields when in awelding area.
6.g. Connect the work cable to the work as close to the weldingarea as practical. Work cables connected to the buildingframework or other locations away from the welding areaincrease the possibility of the welding current passingthrough lifting chains, crane cables or other alternate cir-cuits. This can create fire hazards or overheat lifting chainsor cables until they fail.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “ Standard for Fire PreventionDuring Welding, Cutting and Other Hot Work”, availablefrom NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma022690-9101.
6.j. Do not use a welding power source for pipe thawing.
Jan ‘09
Refer to http://www.lincolnelectric.com/safety for additional safety information.
ivSAFETYiv
Mar. ‘93
PRÉCAUTIONS DE SÛRETÉPour votre propre protection lire et observer toutes les instructionset les précautions de sûreté specifiques qui parraissent dans cemanuel aussi bien que les précautions de sûreté générales suiv-antes:
Sûreté Pour Soudage A L’Arc1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tensionquand la machine à souder est en marche. Eviter toujourstout contact entre les parties sous tension et la peau nueou les vétements mouillés. Porter des gants secs et sanstrous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand onsoude dans des endroits humides, ou sur un planchermetallique ou des grilles metalliques, principalement dansles positions assis ou couché pour lesquelles une grandepartie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câblede soudage et la machine à souder en bon et sûr étatdefonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour lerefroidir.
e. Ne jamais toucher simultanément les parties sous tensiondes porte-électrodes connectés à deux machines à souderparce que la tension entre les deux pinces peut être letotal de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source decourant pour soudage semi-automatique, ces precautionspour le porte-électrode s’applicuent aussi au pistolet desoudage.
2. Dans le cas de travail au dessus du niveau du sol, se protégercontre les chutes dans le cas ou on recoit un choc. Ne jamaisenrouler le câble-électrode autour de n’importe quelle partiedu corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,donc:
a. Utiliser un bon masque avec un verre filtrant appropriéainsi qu’un verre blanc afin de se protéger les yeux du ray-onnement de l’arc et des projections quand on soude ouquand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger lapeau de soudeur et des aides contre le rayonnement del‘arc.
c. Protéger l’autre personnel travaillant à proximité ausoudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc desoudage. Se protéger avec des vêtements de protection libresde l’huile, tels que les gants en cuir, chemise épaisse, pan-talons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone desoudage. Utiliser des lunettes avec écrans lateraux dans leszones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin deprévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé dela masse. Un court-circuit accidental peut provoquer unéchauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possiblede la zone de travail qu’il est pratique de le faire. Si on placela masse sur la charpente de la construction ou d’autresendroits éloignés de la zone de travail, on augmente le risquede voir passer le courant de soudage par les chaines de lev-age, câbles de grue, ou autres circuits. Cela peut provoquerdes risques d’incendie ou d’echauffement des chaines et descâbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.Ceci est particuliérement important pour le soudage de tôlesgalvanisées plombées, ou cadmiées ou tout autre métal quiproduit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenantd’opérations de dégraissage, nettoyage ou pistolage. Lachaleur ou les rayons de l’arc peuvent réagir avec les vapeursdu solvant pour produire du phosgéne (gas fortement toxique)ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,voir le code “Code for safety in welding and cutting” CSAStandard W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POURLES MACHINES À SOUDER ÀTRANSFORMATEUR ET ÀREDRESSEUR
1. Relier à la terre le chassis du poste conformement au code del’électricité et aux recommendations du fabricant. Le dispositifde montage ou la piece à souder doit être branché à unebonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seronteffectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leurplace.
vv
TThhaannkk YYoouu for selecting a QUALITY product by Lincoln Electric. We want youto take pride in operating this Lincoln Electric Company product••• as much pride as we have in bringing this product to you!
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep ithandy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.The level of seriousness to be applied to each is explained below:
WARNINGThis statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.
This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.
CAUTION
Please Examine Carton and Equipment For Damage ImmediatelyWhen this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claimsfor material damaged in shipment must be made by the purchaser against the transportation company at thetime the shipment is received.
Please record your equipment identification information below for future reference. This information can befound on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information youhave recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration- Register your machine with Lincoln Electric either via fax or over the Internet.• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.• For On-Line Registration: Go to our WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
CUSTOMER ASSISTANCE POLICYThe business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask LincolnElectric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating orcorrecting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter anywarranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the controlof, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained inapplying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.comfor any updated information.
vivi TABLE OF CONTENTSPage
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––Installation.......................................................................................................................Section A
Technical Specifications.......................................................................................................A-1Safety Precautions ...............................................................................................................A-2Location................................................................................................................................A-2Weld Cable Sizes .................................................................................................................A-2Coaxial Weld Cable..............................................................................................................A-3Wire Drive Cable .................................................................................................................A-4Shielding Gas Connection....................................................................................................A-5Wire Drive Configuration ......................................................................................................A-6Changing The Gun Receiver Bushing..................................................................................A-6Procedure to Install Drive Rolls and Wire Guides ................................................................A-7Conduit Installation...............................................................................................................A-8System Set-Up .....................................................................................................................A-9
________________________________________________________________________________Operation.........................................................................................................................Section B
Safety Precautions ...............................................................................................................B-1Graphic Symbols that appear on this Machine or in this Manual .........................................B-1Definition of Welding Terms .................................................................................................B-2Product Description ..............................................................................................................B-2Recommended Processes, Equipment Limitations, Recommended Power Sources ..........B-2
________________________________________________________________________________Accessories ....................................................................................................................Section C
Optinal Kits and Accessories ...............................................................................................C-1Drive Roll Kits used..............................................................................................................C-1Accessories Used.........................................................................................................C-2, C-3
________________________________________________________________________________Maintenance....................................................................................................................Section D
Safety Precautions ...............................................................................................................D-1Routine Maintenance ...........................................................................................................D-1Periodic Maintenance...........................................................................................................D-1Calibration Specification.......................................................................................................D-1
________________________________________________________________________________Troubleshooting .............................................................................................................Section E
How to Use Troubleshooting Guide .....................................................................................E-1Troubleshooting Guide .................................................................................................E-2, E-3
________________________________________________________________________________
Wiring Diagram & Dimension Prints .............................................................................Section F________________________________________________________________________________
Parts Pages ................................................................................................................P-569 Series_______________________________________________________________________________
A-1INSTALLATION A-1
AutoDrive 4R90
TEMPERATURE RANGE
OPERATION: -40°F to 104°F (-40°C to 40°C)STORAGE: -40°F to 185°F (-40°C to 85°C)
INPUT VOLTAGE, CURRENT
TECHNICAL SPECIFICATIONS – AutoDrive 4R90 (K2685-2)
HEIGHT WIDTH LENGTH WEIGHT
8.4 Inches 7.5 Inches 9.1 Inches 13.2 lbs(213 mm) ( 191 mm) (231 mm) (6.0 kg)
PHYSICAL DIMENSIONS
INPUT VOLTAGE ± 10%0-40 VDC
INPUT AMPERES4A
RATED OUTPUT @ 104°F (40°C)DUTY CYCLE
100% rating
INPUT AMPERES
500
GEARING - WIRE FEED SPEED RANGE-WIRE SIZE
WFS RANGE
50 – 800 ipm(1.3 – 20.3m/min)
WFS RANGE
50 – 800 ipm(1.3 – 20.3m/min)
WIRE SIZES
.023 – .045"(0.6 – 1.2mm)
WIRE SIZES
.035 - .045”(0.9 – 1.2mm)
GEARING
K2685-2
GMAW FCAW
WELD CABLE SIZE
Table A.1 located below are copper cable sizes rec-ommended for different currents and duty cycles.Lengths stipulated are the distance from the welder towork and back to the welder again. Cable sizes areincreased for greater lengths primarily for the purposeof minimizing cable drop.
** Tabled values are for operation at ambient temperatures of 104°F(40°C) and below. Applications above 104°F(40°C) may require cableslarger than recommended, or cables rated higher than 167°F(75°C).
RECOMMENDED CABLE SIZES (RUBBER COVERED COPPER - RATED 167°F or 75°C)**CABLE SIZES FOR COMBINED LENGTHS OF ELECTRODE AND WORK CABLES
AMPERES
200200225225250250250250300325350400400500
PERCENTDUTYCYCLE
6010020
40 & 3030406010060100606010060
0 to 50Ft.(0 to15m)
22
4 or 53321112/01/02/03/02/0
50 to 100Ft.(15 to 30m)
2233321112/01/02/03/02/0
100 to 150 Ft.(30 to 46m)
2222211112/02/02/03/03/0
150 to 200 Ft.(46 to 61m)
111111111/02/02/03/03/03/0
200 to 250 Ft.(61 to 76m)
1/01/01/01/01/01/01/01/02/03/03/04/04/04/0
TABLE A.1
A-2INSTALLATION
AutoDrive 4R90
A-2
SAFETY PRECAUTIONS
ELECTRIC SHOCK CAN KILL.• Turn the input power OFF at thewelding power source beforeinstallation or changing drive rollsand/or guides.
• Do not touch electrically live parts.• When inching with the gun trigger,electrode and drive mechanism are"hot" to work and ground andcould remain energized severalseconds after the gun trigger isreleased.
• Welding power source must be connected tosystem ground per the National Electrical Codeor any applicable local codes.
• Only qualified personnel should perform mainte-nance work.
------------------------------------------------------------------------
WARNING
A-3INSTALLATION
AutoDrive 4R90
A-3
COAXIAL WELD CABLE
Coaxial welding cables are specially designed weldingcables for STT™ and pulse welding. Coaxial weld cablesfeature low inductance, allowing fast changes in the weldcurrent. Regular cables have a higher inductance whichmay distort the STT™ waveshape. Inductance becomesmore severe as the weld cables become longer.
Coaxial weld cables are recommended for STT™ weld-ing, especially when the total weld cable length (elec-trode cable + work cable) exceeds 50 feet (7.6m). SeeTable A.2.
A coaxial weld cable is constructed with multiple smallleads wrapped around one large lead. The large innerlead connects to the electrode stud on the power sourceand the electrode connection on the wire feeder. Thesmall leads combine together to form the work lead, oneend attached to the power source and the other end tothe work piece.
To install:1. Turn the input power off at the welding power source.2. Connect one end of the center lead to the powersource electrode connection, and the other end to thewire feeder electrode connection.
3. Connect the outer lead bundle to the power sourcework connection, and the other end to the work piece.Minimize the length of any work lead extension forbest results.
4. Insulate all connections.
ElectrodeElectrode
WWorkork
Amperes250300350
DutyCycle100%60%60%
0 to 25 Ft.111/0
25 to 50 Ft.111/0
50 to 75 Ft.11--
75 to 100 Ft.11/0--
COAXIAL CABLE LENGTHRECOMMENDED CABLE SIZES (RUBBER COVERED COPPER - RATED 75°C)**
ElectrodeElectrodeWorkWork
ElectrodeElectrode
WorkWork
Power SourcePower Source
Coaxial Weld CableCoaxial Weld Cable
Wire FeederWire Feeder
TABLE A.2
** Tabled values are for operation at ambient temperatures of 104°F(40°C) and below.Applications above 104°F(40°C) may require cables larger than recommended, or cables ratedhigher than 167°F(75°C).
A-4INSTALLATION
AutoDrive 4R90
A-4
A
BK
H N L CDMG
F E
JI
POWER SOURCE WIRE FEEDER
AB K
HNLC
D M G
FE
J
I
Function
Motor PowerMotor PowerGas SolenoidGas SolenoidReservedReserved“2A” Differential Tachometer“2B” Differential TachometerReservedReserved“1A” Differential Tachometer“1B” Differential TachometerReserved“67” Electrode Sense Lead
Pin
ABCDEFGHIJKLMN
WIRE DRIVE CABLE, K1785-XXWire drive cables are used to connect power sourcesand control boxes to remote wire drives.
The cables have a 14 pin connector at each end.Both ends of the cable have a collar and the cablescannot be “daisy chained” to make a longer cable.
Function
Motor PowerMotor PowerGas SolenoidGas Solenoid“2A” Differential TachometerReserved+15VDC Tech SupplyTachometer CommonReservedReserved“1A” Differential Tachometer“1B” Differential Tachometer“2B” Differential Tachometer“67” Electrode Sense Lead
Pin
ABCDEFGHIJKLMN
POWER SOURCE WIRE FEEDER
A-5INSTALLATION
AutoDrive 4R90
A-5
SHIELDING GAS CONNECTION
CYLINDER may explode ifdamaged.
• Keep cylinder upright andchained to support.
• Keep cylinder away from areas where it may bedamaged.
• Never lift welder with cylinder attached.• Never allow welding electrode to touch cylinder.• Keep cylinder away from welding or other liveelectrical circuits.
• BUILD UP OF SHIELDING GAS MAYHARM HEALTH OR KILL.
• Shut off shielding gas supply when notin use.
• See American National Standard Z-49.1, "Safetyin Welding and Cutting” Published by theAmerican Welding Society.
------------------------------------------------------------------------Maximum inlet pressure is 100 psi. (6.9 bar.)
Install the shielding gas supply as follows:
1. Secure the cylinder to prevent it from falling.
2. Remove the cylinder cap. Inspect the cylinder valvesand regulator for damaged threads, dirt, dust, oil orgrease. Remove dust and dirt with a clean cloth. DONOT ATTACH THE REGULATOR IF OIL, GREASEOR DAMAGE IS PRESENT! Inform your gas supplierof this condition. Oil or grease in the presence of highpressure oxygen is explosive.
3. Stand to one side away from the outlet and open thecylinder valve for an instant. This blows away any dustor dirt which may have accumulated in the valve out-let.
4. Attach the flow regulator to the cylinder valve andtighten the union nut(s) securely with a wrench. Note:if connecting to 100% CO2 cylinder, insert regulatoradapter between regulator and cylinder valve. Ifadapter is equipped with a plastic washer, be sure it isseated for connection to the CO2 cylinder.
WARNING5. Attach one end of the inlet hose to the outlet fitting ofthe flow regulator. Attach the other end to the weldingsystem shielding gas inlet. Tighten the union nuts witha wrench.
6. Before opening the cylinder valve, turn the regulatoradjusting knob counterclockwise until the adjustingspring pressure is released.
7. Standing to one side, open the cylinder valve slowly afraction of a turn. When the cylinder pressure gagestops moving, open the valve fully.
8. The flow regulator is adjustable. Adjust it to the flowrate recommended for the procedure and processbeing used before making a weld.
A-6INSTALLATION
AutoDrive 4R90
A-6
WIRE DRIVE CONFIGURATION(See Figure A.2)CHANGING THE GUN RECEIVERBUSHING
ELECTRIC SHOCK can kill.• Turn the input power OFF at thewelding power source before instal-lation or changing drive rolls and/orguides.
• Do not touch electrically live parts.• When inching with the gun trigger, electrodeand drive mechanism are "hot" to work andground and could remain energized several sec-onds after the gun trigger is released.
• Do not operate with covers, panels or guardsremoved or open.
• Only qualified personnel should perform mainte-nance work.
------------------------------------------------------------------------Tools required: • 1/4" hex key wrench.
Note: Some gun bushings do not require the use ofthe thumb screw.
1. Turn power off at the welding power source.
2. Remove the welding wire from the wire drive.
3. Remove the thumb screw from the wire drive.
4. Remove the welding gun from the wire drive.
5. Loosen the socket head cap screw that holds theconnector bar against the gun bushing.Important: Do not attempt to completelyremove the socket head cap screw.
6. Remove the outer wire guide, and push the gunbushing out of the wire drive. Because of the pre-cision fit, light tapping may be required to removethe gun bushing.
7. Disconnect the shielding gas hose from the gunbushing, if required.
8. Connect the shielding gas hose to the new gunbushing, if required.
9. Rotate the gun bushing until the thumb screw holealigns with the thumb screw hole in the feed plate.Slide the gun receiver bushing into the wire driveand verify the thumb screw holes are aligned.
10. Tighten the socket head cap screw.
11. Insert the welding gun into the gun bushing andtighten the thumb screw.
GUN RECEIVER BUSHING
THUMB SCREW
SOCKET HEADCAP SCREW
CONNECTOR BLOCK
TIGHTENLOOSEN
WARNING
FIGURE A.2
A-7INSTALLATION
AutoDrive 4R90
A-7
PROCEDURE TO INSTALL DRIVE ROLLSAND WIRE GUIDES
ELECTRIC SHOCK can kill.• Turn the input power OFF at the weld-ing power source before installationor changing drive rolls and/or guides.
• Do not touch electrically live parts.• When inching with the gun trigger, electrodeand drive mechanism are "hot" to work andground and could remain energized several sec-onds after the gun trigger is released.
• Do not operate with covers, panels or guardsremoved or open.
• Only qualified personnel should perform mainte-nance work.
------------------------------------------------------------------------To remove drive rolls and wire guides:
1. Turn power off at the welding power source.
2. Remove the outer wire guide.
3. Rotate all of the triangular rings to the unlockedposition.
WARNING
4. Open the idle arms.
5. Remove the drive rolls and inner wire guide.
To install drive rolls and wire guides:
1. Turn off power at the welding power source.
2. Open the idle arms.
3. Assemble the inner wire guide.
4. Slide the drive rolls onto the drive hubs.
5. Close the idle arms.
6. Rotate all of the triangular rings to the locked posi-tion.
7. Assemble the outer wire guide.
8. Adjust the pressure arms to the recommendedsetting.
INNER WIRE GUIDE
IDLER ARM OPENED
OUTER WIRE GUIDE
A-8INSTALLATION
AutoDrive 4R90
A-8
CONDUIT INSTALLATION
The K1546-xx series of conduits are compatible withK515-xx, K565-xx, Wire Wizard and Electron BeamTechnologies conduits.
To install conduit to the wire drive:
1. Slide the conduit bushing into the feed plate andsecure with the set screw.
2. Slide the conduit into the bushing and lock inplace with the thumb screw.
CONDUIT
CONDUITBUSHING
THUMBSCREW
SETSCREW
A-9INSTALLATION
AutoDrive 4R90
A-9
SYSTEM SET-UP
NEW ARMS
ArcL
ink X
TCo
nnec
tion
ArcL
ink
(5 P
in)
Wor
kSe
nse
Wire
Fee
der
(14 P
in)
Robo
ticTo
rch
Powe
r Wav
e i40
0K2
669-
1
Wor
k Piec
e
FANU
C R-
J30iA
Con
trolle
rwi
th In
tegr
ated
Op
Box
Optio
nal W
ork
Sens
e Lea
d (2
1)
K178
5-XX
Wire
Fee
der
K884
-5,-6
Cont
rol C
able
* Wor
k C
able
(-)
Inte
rnal
ArcL
ink X
TCo
mm
unica
tion
* Elec
trode
Cab
le (+
)
SYSTEM SET-UP (SINGLE NEW ARMS)
Wire
Fee
der
(14 P
in)
Gas
Air
Auto
Driv
e 4R9
0
* Ref
er to
"Out
put C
able
Guid
eline
s" fo
r rec
omm
ende
d ca
ble s
ize
Elec
trode
Conn
ectio
n
B-1OPERATION
AutoDrive 4R90
B-1
• ELECTRIC SHOCK CAN KILL.Unless using COLD FEED fea-ture, when feeding with gun trig-ger, the electrode and drivemechanism are always electri-cally energized and couldremain energized several sec-onds after the welding ceases..
• Do not touch electrically live part or electrodewith skin or wet clothing.
• Insulate yourself from work and ground.• Always wear dry insulating gloves.• Do not operate with covers, panels or guardsremoved or open.
---------------------------------------------------------------------• FUMES AND GASSES can bedangerous.
• Keep your head out of fumes.• Use ventilation or exhaust toremove fumes from breathingzone.
---------------------------------------------------------------------• WELDING SPARKS can causefire or explosion.
• Keep flammable material away.
----------------------------------------------------------------------ARC RAYS can burn.• Wear eye, ear and body protec-tion.
---------------------------------------------------------------------SEE ADDITIONAL WARNING INFORMATIONUNDER ARC WELDING SAFETY PRECAUTIONSAND IN THE FRONT OF THIS OPERATING MAN-UAL.----------------------------------------------------------------------
WARNING
SAFETY PRECAUTIONSREAD AND UNDERSTAND ENTIRE SECTIONBEFORE OPERATING MACHINE.
WIRE FEEDER
POSITIVE OUTPUT
NEGATIVE OUTPUT
INPUT POWER
DIRECT CURRENT
OPEN CIRCUIT VOLTAGE
INPUT VOLTAGE
OUTPUT VOLTAGE
INPUT CURRENT
OUTPUT CURRENT
PROTECTIVEGROUND
WARNING ORCAUTION
U0
U1
U2
I1
I2
GRAPHIC SYMBOLS THAT APPEAR ONTHIS MACHINE OR IN THIS MANUAL
B-2OPERATIONB-2
AutoDrive 4R90
DEFINITION OF WELDING TERMS
GMAW• Gas Metal Arc weldingFCAW• Flux Core Arc WeldingSTT™• Surface Tension Transfer
PRODUCT DESCRIPTION
General Physical DescriptionThe AutoDrive 4R90 wire feeders are powerful yetcompact wire drives for robotic and hard automationapplications.
The MAXTRAC 4 roll wire drive gives steady feedingof all wire sizes and types. The drive features splitwire guides, tool-less drive roll changing, dual springpressure arms and changeable gun bushings allmounted in a precision die cast aluminum frame. Aright angle gear box efficiently transfers motor powerfor both high torque and high speed.
The AutoDrive 4R90 is optimized for the FANUCAM100iC arm. The small, light weight package maxi-mizes arm speed and working envelope. Quickrelease mounting makes for fast servicing of the feed-er and torch.
General Functional DescriptionA high resolution tachometer lets the AutoDrive 4R90accurately feed wire at slow speeds and have gooddynamic response.
RECOMMENDED PROCESSES• GMAW• FCAW• STT™
PROCESS LIMITATIONS
K2685-2 AutoDrive 4R90:ß • Maximum wire size = .045 (1.2mm)
EQUIPMENT LIMITATIONS
K2685-2 AutoDrive 4R90:ß • Maximum GMAW gun length = 10’ (3.1m)ß • Maximum FCAW gun length = 10’ (3.1m)ß • Maximum wire drive control cable length = 100ft(31m)
ß • Robot and power source software may need to beupdated.
ß • Drive rolls are not included with the feeder.ß • Mounts only to FANUC ArcMate100iC arms.
RECOMMENDED POWER SOURCES
ß • Power Wave 355M (requires wire drive board)ß • Power Wave F355iß • Power Wave 455 (all models)ß • Power Wave 455/STT Mß • Power Wave 655/ R
C-1ACCESSORIESC-1
AutoDrive 4R90
WIRE TYPE
Steel Wires:
Cored Wires:
Aluminum Wires:
KITS ELECTRODE SIZE
KP1505-030S .023-.030 (0.6-0.8mm)KP1505-035S .035 (0.9mm)KP1505-040S .040 (1.0mm)KP1505-045S .045 (1.2mm)
KP1505-035C .030-.035" (0.8-0.9mm)KP1505-045C .040-.045" (1.0-1.2mm)
KP1507-3/64A 3/64" (1.2mm)
OPTIONAL KITS AND ACCESSORIES
Includes: 4 V groovedrive rolls and innerwire guide.
Includes: 4 Knurleddrive rolls and innerwire guide.
Includes: 4 polishedU groove drive rolls,outer wire guide andinner wire guide.
DRIVE ROLL KITS 4 ROLL DRIVE
C-2ACCESSORIESC-2
AutoDrive 4R90
K1500-4
K1500-5
K489-7
K515-xxK565-xx
K1546-1
Gun Receiver Bushing (for gunwith K466-3 Lincoln gun connec-tors; compatible with Miller® guns.)
Gun Receiver Bushing (compatiblewith Oxo® guns.)
Gun Receiver Bushing (for LincolnFast-Mate guns.)
Wire ConduitWire Conduit
Incoming Bushing, for LincolnConduit .025- 1/16" (0.6 - 1.6mm)wire. Compatible with Electron
Beam Conduit.
Includes: Gun receiver bush-ing with hose nipple, set screw
and hex key wrench.
Includes: Gun receiver bushingwith hose nipple, 4 guide tubes,set screw and hex key wrench.
Includes: Gun receiver bushingwith trigger connector.
Requires K1546-1Requires K1546-1
Includes: Incoming bushing andhex key wrench.
K1500-1
K1500-2
K1500-3
Gun Receiver Bushing (for gunswith K466-1 Lincoln gun connec-tors; Innershield and Subarc guns)
Gun Receiver Bushing (for gunswith K466-2, K466-10 Lincoln gunconnectors; Magnum 200/300/400guns and compatible with Tweco®
#2-#4)
Gun Receiver Bushing (for gunswith K613-7 Lincoln gun connec-tors; Magnum 550 guns and com-
patible with Tweco® #5)
Includes: Gun receiver bush-ing, set screw and hex key
wrench.
Includes: Gun receiver bush-ing with hose nipple, set screw
and hex key wrench.
Includes: Gun receiver bush-ing with hose nipple, set screw
and hex key wrench.
C-3ACCESSORIESC-3
AutoDrive 4R90
K2175-1
K2175-2
K895-2
K836-1
K884-5
K884-6
K1796-xx
K1785-xx
K1733-1
K590-6
500 lb Accu-Pak Box Payoff Kit
1000 lb Accu-Pak Box Payoff Kit
Rotary Wire Dispenser
Dereeler Adapter
Accu-Trak Drum Payoff Kit – 20inch diameter
Accu-Trak Drum Payoff Kit – 23inch diameter
Coaxial Cables
Wire Drive Cables
Wire Straightener
Water Connection Kit
Includes: 1 cable of length “xx”feet. 14 pin connectors onboth ends. Cable length can-not be extended by connecting
K1785 cables together.
D-1MAINTENANCED-1
AutoDrive 4R90
ELECTRIC SHOCK can kill.• Turn the input power OFF at thewelding power source beforeinstallation or changing driverolls and/or guides.
• Do not touch electrically liveparts.
• When inching with the gun trigger, electrodeand drive mechanism are "hot" to work andground and could remain energized severalseconds after the gun trigger is released.
• Do not operate with covers, panels or guardsremoved or open.
• Only qualified personnel should perform main-tenance work.
----------------------------------------------------------------------
WARNING
SAFETY PRECAUTIONS
ROUTINE MAINTENANCE
To remove the AutoDrive 4R90 for servicing:(See Figure D.1)1. Turn off power to the welding power supply and theentire weld cell.
2. Loosen the thumb screw that secures the torch tothe feed plate.
3. Use a 3/4” (19mm) wrench to remove the electrodecable from the feed plate.
4. Remove the screw from the bottom rear of thefeeder.
5. Slide the feeder back in the bracket and remove.
6. When reassembling the feeder in the mountingbracket, make sure all of the studs fully are fullyengaged in the slots. (See Figure D.2)
PERIODIC MAINTENANCE
CALIBRATION SPECIFICATION
FIGURE D.1
FIGURE D.2
E-1TROUBLESHOOTINGE-1
AutoDrive 4R90
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
This Troubleshooting Guide is provided to help youlocate and repair possible machine malfunctions.Simply follow the three-step procedure listed below.
Step 1. LOCATE PROBLEM (SYMPTOM).Look under the column labeled “PROBLEM (SYMP-TOMS)”. This column describes possible symptomsthat the machine may exhibit. Find the listing thatbest describes the symptom that the machine isexhibiting.
Step 2. POSSIBLE CAUSE.The second column labeled “POSSIBLE CAUSE” liststhe obvious external possibilities that may contributeto the machine symptom.
Step 3. RECOMMENDED COURSE OF ACTIONThis column provides a course of action for thePossible Cause, generally it states to contact yourlocal Lincoln Authorized Field Service Facility.
If you do not understand or are unable to perform theRecommended Course of Action safely, contact yourlocal Lincoln Authorized Field Service Facility.
HOW TO USE TROUBLESHOOTING GUIDE
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.Unauthorized repairs performed on this equipment may result in danger to the technician andmachine operator and will invalidate your factory warranty. For your safety and to avoid ElectricalShock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
WARNING
ELECTRIC SHOCK can kill.• Turn the input power OFF at the welding power source before installation or changingdrive rolls and/or guides.
• Do not touch electrically live parts.• When inching with the gun trigger, electrode and drive mechanism are "hot" to workand ground and could remain energized several seconds after the gun trigger isreleased.
• Welding power source must be connected to system ground per the National ElectricalCode or any applicable local codes.
• Only qualified personnel should perform maintenance work.
WARNING
E-2TROUBLESHOOTINGE-2
AutoDrive 4R90
Observe all Safety Guidelines detailed throughout this manual
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
PROBLEMS(SYMPTOMS)
POSSIBLE CAUSE
RECOMMENDEDCOURSE OF ACTION
The wire feeder does not feed wireand the drive rolls do not spin.
The wire feeds erratically.
No shielding gasVariable or "hunting" arc.
1. Verify the power source is turnedon.
2. Verify the circuit breaker for thewire feeder on the power sourcehas not tripped.
3. Verify power is being supplied tothe wire feeder.
1. Verify the correct drive rolls andinner wire guide are installed inthe wire drive.
2. Check for sharp bends in the gunliner or conduit.
3. Examine the contact tip for wearand proper size. Replace as nec-essary.
4. Check the gun liner and conduit.The welding electrode shouldslide easily through both.
5. Verify the proper gun liner isinstalled.
6. Verify the pressure arms are setproperly. Too much pressure maycrush the wire.
7. Inspect the motor for worn brush-es.
1. Verify the gas supply is turned onand not empty.
2. Check the gas hose for cuts.Make sure it is not crushed.
3. Verify the shielding gas hose isconnected to the gun bushing orwelding gun.
E-3TROUBLESHOOTINGE-3
AutoDrive 4R90
Observe all Safety Guidelines detailed throughout this manual
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact yourLocal Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
CAUTION
PROBLEMS(SYMPTOMS)
POSSIBLE CAUSE
RECOMMENDEDCOURSE OF ACTION
Variable or "hunting" arc.
The motor overload errors occur.
1. Check for proper size contact.Make sure the contact tip is notworn, free of spatter and not melt-ed.
2. Clean and tighten all electrodeand work connections.
3. Verify the proper polarity is beingused for the weld procedure.
4. Make sure the proper electrodestick-out is being maintained.
5. Check the gas flow rate and mix-ture.
6. Verify the gun bushing is tightlymounted to the wire drive.
7. Verify the gun is tightly mountedto the gun bushing.
8. Verify the electrode lead is con-nected to the proper connectionblock on the feed head.
9. Inspect the motor for worn brush-es.
1. Check for sharp bends in the gunliner and conduit.
2. Examine the contact tip for wearand proper size. Replace as nec-essary.
3. Check the gun liner and conduit.The welding electrode shouldslide easily through both.
4. Verify the proper gun liner isinstalled.
5. Reduce the pressure arm setting.
Output Problems
F-1DIAGRAMSF-1
AutoDrive 4R90
B
M 2
1562
552A
TACH
INTE
RFAC
E PC
BD
WIR
ING
DIA
GR
AM
A
UT
OD
RIV
E 4
R90
/4R
220
FE
ED
ER
FEED
PLAT
EP1 8
MO
TOR
/G
EARB
OX
W
TACH
531
BB WBR
537
534
551A
550A
7654321
L2
L1
AJ2 B C D E F G H I J K L M N
P3 87654321
551
550A
552A
553A
500A
515A
842A
843A
551A
GAS
SOLE
NOID
553A
EL
ECTR
ICAL
SYM
BOLS
PER
E15
37
LEAD
CO
LOR
CO
DIN
G
B –
BLAC
K W
– W
HIT
E O
– O
RAN
GE
Y –
YELL
OW
BR
– B
RO
WN
R
– R
ED
NO
TES:
N
.A.
CAV
ITY
NU
MBE
RIN
G S
EQU
ENC
E AS
VIE
WED
FR
OM
CO
MPO
NEN
T SI
DE
OF
PC B
OAR
D.
N.B
. C
AVIT
Y N
UM
BER
ING
SEQ
UEN
CE
AS V
IEW
ED
FRO
M L
EAD
SID
E O
F C
ON
NEC
TOR
.
515A
500A
842A84
3A
58N
.A.
14(J
801)
537
41N
.A. 8
5(J80
0)
12
34
56
78
1 2 3 4 5 6 7 8
534
531
535
535
ORA
NGE
550
GRE
EN
RED
BLAC
K
67A
BLAC
K
BLAC
KRE
DG
REEN
BLAC
K55
355
2BL
ACK
WHI
TE
Y O R
YELL
OW
BRO
WN
RED
BLAC
K
WHI
TE
845A 84
6A
4321
P4
845A
846A
551
550
552
553
67B
67
GND
NOTE: This diagram is for reference only. It may not be accurate for all m
achines covered by this manual. The specific diagram for a particular code is pasted inside
the machine on one of the enclosure panels. If the diagram is illegible, w
rite to the Service Departm
ent for a replacement. G
ive the equipment code number.
F-2DIMENSION PRINTF-2
AutoDrive 4R90
6.02”
4.72”
3.02”
7.50”
3.50”
8.35"
1.46"
1.97"
0.62"
8.35”
9.02”
8.02”
0.27”
0.62”
0.62”
1.97”
1.97”
1.78”
1.46”
1.00”
1.56”
LINC
OLN
ELE
CTRI
C
WARNING
AVISO DEPRECAUCION
ATTENTION
WARNUNG
ATENÇÃO
Spanish
French
German
Portuguese
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE CONSUMABLES TO BEUSED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE ESTE EQUIPO Y LOSCONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT ET LES PRODUITS AETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRODENEINSATZ DES HER-STELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS SIND EBENFALLS ZU BEACHTEN.
� Do not touch electrically live parts orelectrode with skin or wet clothing.
� Insulate yourself from work andground.
� No toque las partes o los electrodosbajo carga con la piel o ropa moja-da.
� Aislese del trabajo y de la tierra.
� Ne laissez ni la peau ni des vête-ments mouillés entrer en contactavec des pièces sous tension.
� Isolez-vous du travail et de la terre.
� Berühren Sie keine stromführendenTeile oder Elektroden mit IhremKörper oder feuchter Kleidung!
� Isolieren Sie sich von denElektroden und dem Erdboden!
� Não toque partes elétricas e elec-trodos com a pele ou roupa molha-da.
� Isole-se da peça e terra.
� Keep flammable materials away.
� Mantenga el material combustiblefuera del área de trabajo.
� Gardez à l’écart de tout matérielinflammable.
� Entfernen Sie brennbarres Material!
� Mantenha inflamáveis bem guarda-dos.
� Wear eye, ear and body protection.
� Protéjase los ojos, los oídos y elcuerpo.
� Protégez vos yeux, vos oreilles etvotre corps.
� Tragen Sie Augen-, Ohren- und Kör-perschutz!
� Use proteção para a vista, ouvido ecorpo.
WARNING
AVISO DEPRECAUCION
ATTENTION
WARNUNG
ATENÇÃO
Spanish
French
German
Portuguese
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES DE USO, E SIGA ASPRÁTICAS DE SEGURANÇA DO EMPREGADOR.
� Keep your head out of fumes.� Use ventilation or exhaust to
remove fumes from breathing zone.
� Los humos fuera de la zona de res-piración.
� Mantenga la cabeza fuera de loshumos. Utilice ventilación oaspiración para gases.
� Gardez la tête à l’écart des fumées.� Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zonesde travail.
� Vermeiden Sie das Einatmen vonSchweibrauch!
� Sorgen Sie für gute Be- undEntlüftung des Arbeitsplatzes!
� Mantenha seu rosto da fumaça.� Use ventilação e exhaustão para
remover fumo da zona respiratória.
� Turn power off before servicing.
� Desconectar el cable de ali-mentación de poder de la máquinaantes de iniciar cualquier servicio.
� Débranchez le courant avant l’entre-tien.
� Strom vor Wartungsarbeitenabschalten! (Netzstrom völlig öff-nen; Maschine anhalten!)
� Não opere com as tampas removidas.� Desligue a corrente antes de fazer
serviço.� Não toque as partes elétricas nuas.
� Do not operate with panel open orguards off.
� No operar con panel abierto oguardas quitadas.
� N’opérez pas avec les panneauxouverts ou avec les dispositifs deprotection enlevés.
� Anlage nie ohne Schutzgehäuseoder Innenschutzverkleidung inBetrieb setzen!
� Mantenha-se afastado das partesmoventes.
� Não opere com os paineis abertosou guardas removidas.