IEEE EMBDDED EEE PROJECT LIST

HYDERABAD | VIJAYAWADA | GUNTUR

Accords IEEE & International Standards Mobile: 9603150547

Vision Solutions

Uppal, Hyderabad | 4/13 Brodipet, Guntur | Benz Circle, Vijayawada

E-Mail:[email protected], call-9603150547

Web site: www.visiongroups.org

Vi

si

on

G

ro

up

s

EEE HARD WARE (KIT) PROJECTS

IEEE & JOURNAL BASED PROJECTS

Project

code

Title of the Project Description

IJEE01 Distribution

Transformer

Monitoring Using

GSM Technology

In this we will monitor transformer parameters like current, voltage

and temperature, if any of these parameters found abnormal then

this systems sends SMS alert to user.

IJEE02 Prepaid Energy Meter

with GSM technology

the GSM technology is used so that the consumer would receive

messages about the consumption of power (in watts) and if it

reaches the minimum amount, it would automatically alert the

consumer to recharge

IJEE03 Bluetooth remote

home automation

system using android

application

With this we can control home appliances from our android phone.

This safe and secure

IJEE04 Substation monitoring

and controlling using

GSM

Substation parameters are monitored and it also send alert message

when these parameters are abnormal

IJEE05 Low cost wireless

sensor network in field

operation monitoring

of ac motor

The main aim of this project is to monitor the operation conditions

of single-phase AC motors



Vision Solutions




Vi

si

on

G

ro

up

s

IJEE06 Applied research of

the intelligent

temperature-controlled

speed adjustable motor

in radiator fan

In this project the speed of the FAN will be controlled automatically

based on current temperature.

IJEE07 Electronic energy

meter with instant

billing

This paper presents automated billing of energy meter. It is just like

postpaid mobile connection. This is useful for billing purpose in

electricity board authority.

IJEE08 Remote power on/off

control and current

measurement for home

electric outlets based

on a low-power

embedded board and

ZIGBEE

We can control the home appliances through ZigBee remote and this

system will display the power consumed by the loads.

IJEE09 Energy saving project

for heating system

with ZigBee wireless

control network

The main of this project is to develop energy saving heating system

using ZigBee wireless technology

IJEE10 Implementation of

ZIGBEE-GSM based

home security

monitoring and remote

control system

The main aim of this project is to develop a security and control

automation system by which we can control and monitor the status

of home appliances

IJEE11 Automation of

residential electricity

cut off using network

based embedded

controller

The main aim of this project is to develop the automation system for

residential electricity cut off using network based embedded

controller

IJEE12 Design of intelligent

streetlight monitoring

The main aim of this project is to design an intelligent streetlight



Vision Solutions




Vi

si

on

G

ro

up

s

system based on micro

controller

monitoring system for power saving

IJEE13 GSM-based wireless

home appliances

monitoring & control

system

The main aim of this project is to develop a system, which uses

Mobile technology that keeps monitoring of the various appliances,

and will control the operation of these appliances with respect to the

signal sent by the mobile

IJEE14 Real-Time

Atomization Of

Agricultural

Environment for

Social Modernization

of Indian Agricultural

System

The main of this project is to control the agriculture motor using

mobile and also to protect the motor

IJEE15 Method of Measuring

Power Quality and

Development of

Monitor Device

The transmission line voltage, current, and power factor, active

power and reactive power are measured and displayed on the LCD

IJEE16 A novel technique of

ac power control using

micro controller based

inverter

The main aim of this work is to design a simple low cost AC voltage

controller used to

Control AC loads which doesn’t demand very high precisions

PROJECTS BASED ON AC TO DC CONVERTERS

AD01

Design Of Controlled

Dc Voltage Regulator

Using Semi Converter

With Motor Drive

230v ac is converted in to dc using SCR's and the required firing

pulses for the SCR's are given by the microcontroller. Only 2 SCR's

and 2 diodes will be there in the converting circuit.



Vision Solutions




Vi

si

on

G

ro

up

s

AD02

Design of controlled

DC voltage regulator

using full wave

converter with motor

speed control

230v ac is converted in to dc using SCR's and the required firing

pulses for the 4 SCR's are given by the microcontroller.

AD03

Design of dual

converter using micro

controller with

lighting load

A Dual converter consists of two full converters connected anti

parallel across the DC load. The four quadrant operation is obtained

by making one converter to work in rectification mode and other in

inversion mode

PROJECTS BASED ON DC TO DC CONVERTERS

DD01

Design And

Implementation Of

Multi Phase(Two-

Phase) Chopper Using

Micro Controller

In this paper we are going to study the designing aspects of multi

phase buck converter by employing controlled switch (MOSFET)

between load and source

DD02

Designing of boost


controller

In this paper we are going to study the designing aspects of boost

converter by employing controlled switches (MOSFET) between

load and source

DD03

Design of two

quadrant/buck-boost


controller

In this paper we are going to study the designing aspects of buck-

boost converter by employing controlled switches (MOSFET)

between the load and source

DD04

Design And

Development Of Fly

Back Converter With

Lighting Load Using

Micro Controller

In this paper we are going to study the designing aspects of fly back

converter by employing controlled switches (MOSFET) between the

load and source



Vision Solutions




Vi

si

on

G

ro

up

s

DD05

Design Of Simple

Buck Converter With

Variable Output

Voltage Using PWM

IC 3525

In this we design the buck converter without micro controller, we

generates pulses from IC3525.

DD06

Implementation Of

Enhanced Buck

Converter Using

Micro Controller With

Variable Output

Voltage

DD08

Design of controlled

DC voltage regulator

using half controlled

converter

PROJECTS BASED ON (DC TO AC) INVERTERS

INV01

Design of 5 level

cascaded multi level

inverter with 1

auxiliary switch

The aim of the project is to study the design and operation of

combined cascaded multi level inverter to provide pure sinusoidal

output voltage

INV02

Design Of Single

Phase PWM H-Bridge

Inverter Using 3525

IC For Variable

Output Voltage

In this project we are going to implement single-phase H-bridge

inverter

INV03

A New Switching

Topology In

Designing Combined

Cascaded Multi Level

Inverter(7 Level)

In this project only 6 switches are used to produce 7 level output.

The switching scheme to the MOSFET switches is implemented

using micro controller.



Vision Solutions




Vi

si

on

G

ro

up

s

With Reduced THD

INV04

Design Of Full Bridge

Inverter With Sine

Wave PWM

Technique Using

Micro Controller For

Motor Application

The aim of the project is to design a single phase sine wave pwm

inverter using micro controller.

INV05

Design of 5 level

symmetrical cascaded

multi level inverter

This paper presents a topology to control cascaded multilevel

inverter that is implemented with multiple DC sources to get 5 level

output

INV06

Single Phase H-Bridge

Inverter With Pulse

Width Modulation To

Reduce Harmonic

Content In The Output

Voltage

The aim of the project is to design and analyze single phase H-

bridge inverter using micro controller.

INV07

Design Of 7 Level

Asymmetrical

Cascaded Multi Level

Inverter With Reduced

Total Harmonic

Distortion

This paper presents a topology to control cascaded multilevel

inverter that is implemented with multiple DC sources to get 7 level

output

INV08

Design Of Single

Phase Parallel Inverter

Employing PWM

Technology Using

Microcontroller

The aim of the project is to design a single phase parallel inverter

using micro controller

INV09

Single phase PWM

half -bridge inverter


with lighting load

The aim of the project is to design and analyze single phase Half

bridge inverter using micro controller



Vision Solutions




Vi

si

on

G

ro

up

s

INV10

Single phase PWM

half-bridge inverter

using 3525 IC with

lighting load

The aim of the project is to design a single phase Half-bridge

inverter using 3525IC.

PROJECTS BASED ON AC TO AC CONVERTERS

AC1

Design of step down

cyclo converter using

dual converter SCR

bridge with lighting

load

Design cyclo converter so as to achieve variable frequency in the

output waveform using a microcontroller.

PROJECTS BASED ON MOTOR CONTROLLERS

MTC01

A Simplified V/F

Control Technique For

Speed Control Of

Induction Motor

To design and analyze the working of induction motor drive so that

the motor can be made to run at various speeds employing V/F

methodology.

MTC02

Speed Control Of Dc

Motor Using Four

Quadrant Chopper

The main aim of the project is to develop a speed control system for

DC motor using four-quadrant chopper. Using four-quadrant

chopper it is possible to demonstrate forward &reverse motoring

and braking

A Novel Solution In

Achieving Variable

To design a drive for speed control of DC motor so that the speed of

the motor can be controlled using PWM technique



Vision Solutions




Vi

si

on

G

ro

up

s

MTC03 Speed Control Of Dc

Motor Using micro

controller

MTC04

Speed Control Of

Induction Motor Using

Voltage Control

Method

To design a drive for driving the induction motor so that the motor

can be made to run at various speeds using voltage control method.

MTC05

Employing Frequency

Control Technique For

Obtaining Variable

Speeds In Driving

Single-Phase

Induction Motor

To design a drive for driving the induction motor so that the motor

can be made to run at various speeds using frequency control

method

MTC06

Variable Speed

Control Of Universal

Motor Using Micro

Controller

To achieve the necessary control over speeds of universal motor

employing PWM technique with microcontroller

PROJECTS BASED ON POWER SYSTEMS

PS01 Transmission Line

Multiple Fault

Ensuring reliable supply to customers is major point in distributing

power. In this project complete protection against such faults are



Vision Solutions




Vi

si

on

G

ro

up

s

Detection And

Indication To

Substation Using

Wireless Technology

monitored & if any fault occurs, it indicates to nearby substation

through RF technology.

PS02 Automatic power

factor correction using

switching capacitors

In this power factor correction unit it consists of a number of

capacitors that are switched by means of relays. These

contactors/relays are controlled by a regulator that measures power

factor in an electrical network. Depending on the load and power

factor of the network, the power factor controller will switch the

necessary blocks of capacitors in steps to make sure the power

factor stays above a selected value.

PS03 Unbalanced Three-

phase Optimal Power

Flow for Smart Grids

Whenever a three phase load is unbalanced it will correct the load

by switching some of the single phase loads to the other phases.

PS04 Substation monitoring

system (measurement

of PF, voltage, current,

temp.)

Continuous monitoring of substation is essential for reliable& safer

power supply at customer point. In this project are going to monitor

various supply parameters viz., voltage, frequency, p.f, power

ensuring protection

PS05 Transformer oil

temperature

monitoring with

automatic Circuit

Breaker operation.

The temperature of the transformer oil is monitored and displayed

on the LCD. When the temperature increases we will switch ON

cooling FAN. Even after switching the FAN if the temperature is not

decreased then we will switch of the transformer by using a relay.

Bulb is connected as a load.

PS06 Single phasing

preventer for

protection of three

phase (3-ph) loads

All the three phase induction motors need the power supply in all

the three phases when it is running if any of the phases is having a

power outage then the motor is switched off by using relay and the

fault phase is displayed on the LCD so that problem can be solved

easily

PS07 Automatic switching

of consumer

connection in

In the distribution feeder if the single phase consumer loads and

unbalancing a three phase system then the consumers are switched

to other phases so that the overall three phase system will remain in



Vision Solutions




Vi

si

on

G

ro

up

s

distribution feeder for

different load

distribution

balanced condition

PS08 Automatic change

over for three phase

connection with data

logger


by switching some of the single phase loads to the other phases and

the status of all the loads is shown on the display.

PS09 Automatic switching

of consumer

connection in


different load

distribution

In the distribution feeder if the single phase consumer loads and

unbalancing a three phase system then the consumers are switched

to other phases so that the overall three phase system will remain in

balanced condition.

PS10 Auto selection of any

available phase in 3

phase supply system

When a single phase load is connected to a phase which is having a

power outage then the load is automatically switched to another

phase by using relays so that the availability of the single phase

from the three phases will be more.

PS11 An On-line

Monitoring System of

Transmission Line

Conductor

When there is a fault in the power supply the load is switched off by

using a relay and the type of fault i.e. over voltage, under voltage

and over current is displayed on the LCD.

PS12 Over voltage or under

voltage tripping

mechanism

Whenever there is fault in the transmission line the load is switched

off and the type of the fault is displayed on the display. If the fault if

temporary fault then the load is reconnected to the line if not the

load remains disconnected. And the faulty phase is also displayed on

the display.

PROJECTS BASED ON SOLAR POWER



Vision Solutions




Vi

si

on

G

ro

up

s

SL01 Solar based sinusoidal

PWM inverter using

parallel inverter.

To design solar based H-Bridge inverter using micro controller

employing PWM technology.

SL02 Implementation Of

Solar Based Full

Bridge Inverter With

PWM Technique

The aim of the project is to design a solar based parallel inverter


SL03 Solar based off grid

parallel inverter

Design using ic 3524

The aim of the project is to design a solar based parallel inverter

using 3525 IC.

SL04 Solar based energy

backup system using

micro controller

The aim of the project is to design a solar based energy backup

system using micro controller.

SL05 Solar based

irrigation pumping

system for rural

agriculture

applications

The aim of the project is to design a working model of irrigation

pumping system making use of renewable energy resource solar

power

SL06 Distribution grid

transformers

monitoring using

GSM with forced

cooling control



Vision Solutions




Vi

si

on

G

ro

up

s

SL07

To Design High

Efficient Traffic

Lights Control

System Utilizing

Solar Energy

Traffic Lights are controlled based on time and power for these

lights is obtained from Solar panel.

SL08

To Design Accurate

Wireless Load

Measuring Meter

For Power Lines

SL09

Wireless motor starter

with

acknowledgement

using solar energy for

agricultural

application

This system is used to give information to formers about power

status and we can control the motor without going to the field with

SMS

SL10

Solar pv cell tracking

system for obtaining

maximum power

output

The project aims at designing a system that would sense and follow

the position of the sun and rotate the panel in the direction of the sun

to obtain maximum power output

SL11 Solar based LED

street light system

with time controlled

and auto dimming

This project is design to reduce the power with present street light

system.



Vision Solutions




Vi

si

on

G

ro

up

s

based on ambient light

SL12 Designing of data

logger of Solar panel

PROJECTS BASED ON APPLICATIONS

AS01 Smart Remote for

controlling electrical

appliance through

android mobile.

With this we can control any electrical appliances with our android

phone, no need of another remote .It is safe and secure also.

AS02 Virtual nurse-

controlling wheel chair

through android mobile

With this the patient can easily control his wheel chair through

simple and smart touching of android mobile

AS07 Smart Home/office

automation through

android mobile.

With this we can control any electrical appliances in home or office

or industry with our android phone, no need of another remote .It is

safe and secure also.

AS09 Smart regulator for

controlling fan speed

through Android

mobile.

With this we can control speed of fan or AC from our android

mobile.

AS10 AC motor speed

controller through

Android mobile.

With this we can control speed of AC motor from our android

mobile

AS11 Advanced street light

controlling system

through smart phone.

In this we can control street light from anywhere through smart

phone.



Vision Solutions




Vi

si

on

G

ro

up

s

AS13 Industry/home/office

automation through

smart phone.

With this project we can control any electrical appliances of office

or home or industry from anywhere by using Smart phone.

AS14 Industrial parameters

monitoring system

through Smartphone

We can monitor different parameters like temperature, voltage, etc

through online using smart phone from anywhere

VP08 Home /office/industry

electrical appliances

controlling by phone

call and confirmation

through voice feedback.

In this we will switch off and switch on any electrical appliances

just by calling to this system and press some buttons using DTMF

technology. This system also sends voice feedback of device status

that is whether device is on or off.

VP12 Substation monitoring

and controlling system

with voice alerts.

This system monitor the different parameters of substation like

voltage, current and temperature and gives respective voice alerts

when something goes abnormal condition and takes necessary

action.

FS01 Standalone data logger

in SD/MMC card with

time stamp for

industrial applications.

In this we will monitor and store different parameters in industry

like temperature, voltage, etc .We will store these parameters values

in SD card along with measured time and date also. The stored data

format will be in .txt file or excel format so that we can go through

entire monthly data using system.

FS05 Advanced embedded

system based a

paperless feedback

system for colleges and

event management

systems

As we know to save our world we have to reduce usage of paper.

This project helps in eliminate papers used in feedback systems. In

this the feedback and suggestions should be entered from key board

and this data will be stored in memory card in a file format using

ARM7 micro controller.

ET01 Industry parameters

monitoring and

controlling system

based on embedded

web server.

In this we will monitor industry parameters like current, voltage,

temperature, etc through online using internet from anywhere in the

world and we can also control electrical appliances from internet.



Vision Solutions




Vi

si

on

G

ro

up

s

ET03 Zigbee and internet

based advanced street

light controlling

system.

With the help of internet and Zigbee technology we can reduce man

power in street light controlling process. We can control street lights

from online itself.

ET05 Internet based

home/office

automation.

With this system we can control any electrical appliances of home

or office from anywhere in the world using internet.

EE01 Wireless Scrutinizer for

Detecting the fault in

Power System.

We take a 230v supply voltage and measure the current in it. Fault

condition is created by using bulbs. We measure the input and

output current of the load using 2 ct's. When the bulb is on we

assume fault is created and it is indicated in another section using rf.

EE02 Wireless load

measuring meter for

power line.

The power in the transmission line is calculated by measuring

voltage, current, power factor, and this is indicated in the display by

sending the data wirelessly.

EE03 Up-to-date Recording

System of Power Line

Losses.

The power loss in the transmission line is calculated by measuring

the voltage drop in the line. The voltage drop is created by using a

resistor and an inductor.

EE04 Underground cable

fault identification.

.

The objective of this project is to determine the distance of

underground cable fault from base station in kilometers

EE05 Two quadrant chopper

drive for DC motor

speed control.

This can be done for small dc motor as well for big (around half hp)

motors also depends upon motor availability.

EE06 Wireless motor starter

with acknowledgement

using solar energy for

agricultural application

This system sends a message to user when power comes an also

sends information whenever power is absent. This system works

with solar energy

EE07 Four quadrant chopper

drive for DC motor

speed control

This can be done for small dc motor as well for big (around half hp)

motors also depends upon motor availability



Vision Solutions




Vi

si

on

G

ro

up

s

EE08 design of closed loop

controlled DC voltage

regulator using full

wave semi- converter

the 230v ac is converted in to dc using SCRs and the output voltage

is measured by the ADC and the firing angle of the SCRs is

controlled by the microcontroller only 2 SCRs and 2 diodes will be

there is converting circuit

EE09 Automatic power factor

correction using

switching capacitors.

The power factor is measured by using zero crossing detectors and it

is corrected by connecting the capacitors using TRIACs or relays.

EE10 Automatic power factor

correction using static

VAR compensators.


is corrected by connecting a single capacitor of larger value using

TRIAC and by controlling the firing angle.

EE11 Design of closed loop



wave converter.

The 230v ac is converted in to dc using SCRs and the output voltage


controlled by the microcontroller only 4 SCRs will be there in

converting circuit.

EE12 Three phase load

protector with

automatic fault

indication using micro

processor.

Whenever a three phase fault is occurred it will be indicated by

using OP-AMPS and by measuring voltages and currents. And the

type of fault is indicated in the display.

EE13 Thyristor based soft

starter.

The advantage of these starters is the starting current can be

controlled to a much lower values than that of the value achieved

with the traditional starters.

EE14 Thyristor based

star/delta starter.

6 bulbs are used to represent the motor. There are connected to form

into 3 pairs with 2 each connected in series. They are connected in

star first then in delta to the three phase supply.

EE15 Unbalanced Three-

phase Optimal Power

Flow for Smart Grids.





Vision Solutions




Vi

si

on

G

ro

up

s

EE16 Maximum Demand

Controller for

Industries.

This system automatically switches off the low priority appliances

whenever maximum load power reached.

EE17 Automatic Switching of

consumer connection in


efficient load

distribution



EE18 Distribution grid

transformers

monitoring using GSM

with forced cooling

control system

The data at the distribution transformer is observed using GSM and

if there is any fault it will on the cooling fans. If the fault is on

current then it will switch off the transformer

EE19 Remote substation

monitoring system

using bidirectional

power line

communication.

With the same 230 v power line we can monitor substation

parameters.




wave converter through

computer.

the 230v ac is converted in to dc using SCR's and the output voltage


controlled by the microcontroller only 2 SCRs and 2 diodes will be

there is converting circuit. The required output voltage is set by

using hyper terminal.


controlled ac voltage

regulator using TRIAC.

Same as the speed control of ac motor but here output voltage is

measured using ADC.

EE22 Transmission line

multiple faults

detection and indication

to electricity board.

Voltage and current faults are detected using differential protection

scheme and the type of the fault is transmitted using RF.



Vision Solutions




Vi

si

on

G

ro

up

s

EE23 Power theft

identification system in

distribution lines using

differential power

measurement.

Current at both the ends of transmission line are measured using

CTs and if there is a difference in those currents it means power was

theft.

EE24 Automatic transformer

shunt and series

parameter calculation

from open circuit and

short circuit test

reading.

The OC and SC test readings of the transformer are given through

keypad and microcontroller will do calculation and give the output

on the LCD.

EE25 Closed loop dc motor

speed control.

In this we will control the speed of dc motor and we also take the

feedback from the motor and correct the speed level to desired level.

EE26 Design of cyclo


controller.

The input supply frequency is about 50 Hz. We can get the

multiples of 50hz using the SCRs. controller will generate pulses for

4 SCRs and the output frequency of the sine wave is controlled.

EE27 Reverse power

protection for

generator.

The phase angle of the current and voltage are measured to measure

whether the power is in reverse direction of not if the power is in

reverse direction then it will switch of the supply.

EE28 Automatic transformer

protection using

numerical relay.

Difference in currents of the two current transformers' will give a

buzzer sound.

EE29 Automatic

sequence corrector.

Whenever the RYB phase sequence is changed it will be corrected

by using relays.

EE30 Design of earth fault

relay.

Whenever there is an internal fault or the earth fault then we can

sense that by measuring the magnitude of the current and this will

give type of the fault.

EE31 Reactive power

compensation using


is corrected by connecting a single capacitor of larger value using



Vision Solutions




Vi

si

on

G

ro

up

s

STACOM. TRIAC and by controlling the firing angle.

EE32 Speed control of

universal motor using

IGBT.

This will be same as the speed control of the ac motor using TRIAC

but only difference is IGBT is used to vary the voltage and we will

control the dc voltage. First we will convert the 230v ac into dc and

then we will control.

EE33 Efficient power saver

for street lights using

LDR, RTC, LEDs light

with solar power

This project saves more power that is being wasted in present street

light switching. In this we will consider time and sunlight intensity

and we use LED lights and solar power

EE34 Agricultural motor

controlling with motor

safety and water level

indicator using GSM.

The former can control his field motor without need of going to his

field just by sending message. This system also provides safety

motor from over heat, low phase power and water level indication.

EE35 Automatic changeover

for 3 phases

connections with data

logger.



EE36 Solar Tracking system

for Maximum power

output with real time

power monitoring

system.

In this the panel will give maximum power by changing its direction

according to sun light direction.

It can be done with two motors arrangement or single motor

arrangement

EE37 Voice guider and

medicine reminder for

patients and old age

persons.

In this the user will be given one remote (IR or RF or ZIGBEE), he

has to press any button to get what service he wants and that is

played from voice IC so that any person can hear it and come to the

user. Another feature of this project is to remind the user for

medicines.

EE38 Broken conductor

detection for overhead

lines.

The broken conductor can be sensed by using the voltage drop in

the line. We will give three switches to indicate broken condition

when the switch is operated it will indicate which switch is operated

in terms of kilometers.



Vision Solutions




Vi

si

on

G

ro

up

s

EE39 Intelligent shopping

trolley using RFID

With this we can save billing time and instantaneously the rate and

expiry date of the product will be displayed so that we can do the

shopping within our budget.

EE40 Elegant home with

power saving, security,

safety, remote

controlling and auto

control of water tank

motor

In this we will provide multi features to home like remote

controlling of home appliances ,auto controlling of lights depends

upon sunlight and auto controlling of water tank motor when tank

is full and alert the user when intruders come or when gas leakage

or fire accident occurs

EE41 Intelligent train engine

to avoid accidents and

controlling railway gate

automatically

In this we will control the train by monitoring the driver’s position

or activeness and the gate will b e controlled automatically when

train is near the gate.

EE42 Design And

Development Of

Prepaid Energy Meter

With Serial Data

Transmission

In this we have one smart card which contains number units

depends upon the amount we will pay. These units will be given to

energy meter system to activate and it will supply power to home

till that units are consumed and we have recharge same card again.

EE43 Protection And Control

Of Low Voltage

Motors Used In

Industrial Applications.

The motor will be protected from over voltage, current, temperature

and ground fault conditions. This system immediately switches off

the motor whenever abnormal condition occurs and intimate to

control room through RF communication.

EE44 Flexible load sharing of

transformer with GSM

SMS

It continuously measure the load current and it shares this

load with another transformer when the load is more and

send an alert through message. The user can also share

directly whenever he wants just by sending message

EE45 Agriculture field motor

control system using

GSM

Motors in the field are controlled with the help of predefined SMS.

EE46 Industrial Electrical

Devices Control

By this project, we can control the devices in the industries by



Vision Solutions




Vi

si

on

G

ro

up

s

System sending predefined SMS to the controlling unit.

EE47 GSM based DC

Motor Speed and

Direction Control

The speed and direction of DC motor can be controlled by sending

predefined SMS to the system

EE48 Cell Phone based

Street Light

Controlling System

with light failure

indication system.

The on and off controls of the street lights can be done using GSM

technology. If any light does not work then that information is sent

as message to electricity department.

EE49 Temperature

Measurement over

GSM Mobile

Temperature sensor is used to measure the temperature in a

particular room and this measured value is sent through GSM to the

user mobile.

EE50 Password protected

GSM based Device

control.

Controlling the devices from remote places only by authorized

persons.

EE51 Fingerprint based

Access Control system

Security is provided in restricted areas using fingerprint technology.

The persons are asked to give their fingerprint and the system

compares this fingerprint with the already stored information in the

system and only allows into if it is an authorized one.

EE52 Finger print based

elevator (lift) operating

system.

Only authorized persons are allowed to access the lift controls.

EE53 Low Cost Wireless

Sensor Network In

Field Operation

Monitoring Of AC

Motor.

The motor will be protected from over voltage, current, temperature

and ground fault conditions. This system immediately switches off

the motor whenever abnormal condition occurs and intimate to

control room through RF communication.

EE54 A Zigbee Smart Energy

Meter Implementation

For Energy Efficient

In This system one control system collects the data from different

meters in the building and we can control the appliances of each

floor through this control system.



Vision Solutions




Vi

si

on

G

ro

up

s

Buildings.

EE55 Development of a smart

power meter for AMI

based Zigbee

communication

Advanced Metering

Infrastructure (AMI).

This will be useful in heavy apartment’s .individual meters data will

be collected and maintained by main system .this main system sends

collated data to electricity board.

EE56 Remote Power On/Off

Control And Current

Measurement For

Home Electric Outlets

Based On A Low-

Power Embedded

Board And Zigbee

Communication

We can control the home appliances through Zigbee remote and this

system will display the power consumed by the loads.

EE57 Remote-Controllable

and Energy-Saving

Room Architecture

Based on Zigbee

Communication.

In this we can control the loads through Zigbee remote or they will

also be controlled automatically to save the power.

EE58 Applications of Short

Range Technologies to

Industrial Automation:

A Zigbee Approach.

Industrial devices are monitored and controlled using Zigbee

Technology.

EE59 System for Measuring

Power Parameters with

Zigbee Connectivity.

This system measures the power from each home and sends to

central system which is useful in apartments.

EE60 Wireless Data

Encryption and

Decryption Using

ZigBee

Which used in security applications



Vision Solutions




Vi

si

on

G

ro

up

s

EE61 ZigBee Based

Automated Irrigation

System.

Using ZigBee this system controls the irrigation system

automatically.

EE62

Bluetooth Robot with

CMOS image

sensor(SPY ROBOT)

We can control this robot through Bluetooth from PC and the video

sent by robot can be seen in TV or PC

EE63 Remote controlled

home automation using

Bluetooth

With this we can control home appliances like lights, fan, motor, etc

through Bluetooth. This is safe and secured.

EE64 Bluetooth based

industrial data

acquisition system

This project measures different parameters in industry like voltage,

current and temperature and transmit this data to PC continuously

through Bluetooth.

EE65 Industrial devices

controlling system

using Bluetooth

With this we can control industry appliances like machines and

motors through Bluetooth. This is safe and secured.

EE66 Intelligent electricity

billing system using

Bluetooth

This system receives the units consumed from various meters and

generates the bill accordingly. This saves the cost, time and

manpower.

EE67 Touch screen based

smart home automation

We can control the home appliance just by smart touch

EE68 Electrical parameters

data logger

In this we will continuously measure and display electrical

parameters like voltage, current, frequency and temperature

EE69 Smart horn for vehicles

with alcohol detection

for drivers

This system reduces the sound pollution that is generated by

unnecessary use of horn. This controls the horn intensity depends

upon vehicle distance and also gives the special sound when object

is detected at back side if vehicle moves backside and this system

only allows for driving if driver does not consume alcohol

EE70 Smart blind stick with

ultra sonic sensor.

This stick gives different sound intensity depends upon the object

distance from person or we can play some voice also depends upon



Vision Solutions




Vi

si

on

G

ro

up

s

distance.

EE71 PIR sensor based power

saver for auditorium

and conference halls.

This project is used to save the power in conference halls and in

auditoriums. When there are no persons in the hall ,then lights and

fans will be switched off automatically

EE72 Intelligent security and

safety system for

colleges and industries

This project detects fire accidents, gas leakages and also alert

through SMS when main door is closed without closing any other

room entrance or if any other door is opened without opening main

door

EE73 An Efficient

Monitoring Of

Substations Using

Microcontroller Based

Monitoring System

using RF

This system monitors the subsystem to provide safety and intimate

to control room through RF

EE74 Wireless Power Grid

Controller

With this we can control the power grid through PC using RF

communication

EE75 RF based industrial

Automation System

The industrial loads like motors, coolers, etc are monitored and

controlled by a RF remote.

EE76 DC motor speed and

direction control using

RF

In this project we can control speed and direction of DC motor

depending on the requirement using RF signals

EE77 Wireless Stepper motor

control using RF

The stepper motor direction can be controlled using RF

communication.

EE78 Power Management

System in Hotels using

PC.

The various appliances in the hotels are controlled by giving

commands from the PC.

EE79 PC based Hi-tech

Home Implementation.

We can control the home appliances just by sitting in front of PC.



Vision Solutions




Vi

si

on

G

ro

up

s

EE80 Industrial

Automation using

PC.

The industrial appliances are controlled by the commands issued

from the PC. The controlling unit receives these commands from the

PC and controls the devices according to the commands.

EE81 Industrial electrical

appliances control

using IR.

To reduce the manpower for controlling the devices we are

implementing this project. Here we will be controlling devices by

using a general TV REMOTE.

EE82 DC motor speed and

direction control using

IR.

A DC motor is controlled using wireless communication. In this

project we can control the speed of the dc motor and its direction.

EE83 Stepper motor control

using IR

The direction of the stepper motor can be controlled using an IR

remote.

EE84 Automatic Room light

controller with visitor

counter using IR.

This project displays the number of persons present in the room and

controls the light according to the intensity of daylight.

EE85 Auditorium Controlling

System

The lights and fans in auditorium are controlled by IR remote.

EE86 Shopping Malls

Security and Power

Management System

using IR

The design of security and the method of consuming the power in

the shopping malls are carried out in this project.

EE87 AC motor speed control

using TRIAC

The speed of AC motor can be varied rapidly on and off by TRIAC.

EE88 Phase Sequence

Indicator and

Controlling System.

The controlling unit continuously whether 3-phase is coming from

the line or not so as to run the motors which run only with 3-phase.

If 3-phase is not coming, the controlling unit automatically shuts

down the system.

EE89 Boiler Monitoring and

Control System.

The temperature is measured and controlled for the industrial

boilers.

EE90 Involuntary Industrial The power management in the industries can be done effectively



Vision Solutions




Vi

si

on

G

ro

up

s

Power Scheduler using

Embedded System.

using this project.

EE91 Power Saver for

Advertisement

Hoardings using RTC.

This system switches on the lights only at preprogrammed timings

using RTC thus saving the power up to the maximum extent.

EE92 Solar Tracker for

acquiring maximum

power.

The project aims at designing a system that would sense and follow

the position of the sun and rotate the panel in the direction of the

sun to obtain maximum power output.

EE93 Water Scheduling

for Municipalities

Water supply to different localities is done on time basis. The

supply will be automatically cut once the time allotted to that

particular locality lapses.

EE94 Electronic Security

System for

Homes/Industries

with auto dialer.

This system provides security to the homes or offices by interfacing

sensors with the controlling units. If anything goes wrong, the

system automatically dials up to the predefined number and also

activates the alert system.

EE95 Energy Saver for

Automatic Room Light

Controller with Visitor

Counter

The system aims at saving the power by switching on/off the light

depending upon the sensor output. It also counts the number of

persons present in the hall and displays this value on the LCD.

IEEE EMBDDED EEE PROJECT LIST

Engineering

Transcript of IEEE EMBDDED EEE PROJECT LIST