IEC 120 1984
-
Upload
jose-miguel-acuna-elgueda -
Category
Documents
-
view
268 -
download
58
Transcript of IEC 120 1984
\IEC
Publication 120 de la CE1
Dimensions des assemblages à rotule et logement de rotule
des éléments de cha9nes d'isolateurs
( T r o i s i h e édition - 1984) IEC Publication 120
Dimensions o f ball and socket couplings o f string
insulator units
(Third edition - 1984)
C O R R I G E N D U M
Page 10
Article 9.
Clause 9.
Remplacer le tableau existant par ce qui suit:
Replace the existing table by the following:
Dimensions dë la tige à rotule
Dimensions of the pin ball
DBsignstion de 1 'assmbl8ge Designated si&
o f coupling
11
I I I I I I I I I I
20
24 o 40 70 O O 25-i , 4 ~ 9 - 1 ~ 8 21-lr7
' 0 28 29-ï, i 57,1,9 23,5-!.s 55 80
O
32
* Donné à t i t re i n d i c a t i f , Given for gu idance .
I
+1 3-o, 5
t1 5r7 1 3r5,1
+ l r 5 I 4r5-i,o
Hai 1989 May 1989
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
C O M M I S S I O N É L E C T R O T E C H N I Q U E I N T E R N A T I O N A L E
N O R M E D E L A C E 1
I N T E R N A T I O N A L E L E C T R O T E C H N I C A L C O M M I S S I O N
I E C S T A N D A R D
Publication 120 Troisième édition - Third edition
1984
Publication 120 -
Dimensions des assemblages à rotule et logement de rotule des éléments de chaînes d'isotateurs
Dimensions of ball and socket couplings of string insulator units
@ C E 1 1984
Droits de reproduction réservés - Copyright - all rights reserved
Bureau Central de la Commission Electrotechnique Internationale 3, rue de Varernbé Genève, Suisse
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 120 B 4 m 4844871 0007877 B m
Révision de la présente publication
Le contenu technique des publications de la C E I est cons- tamment revu par la Commission afin d'assurer qu'il reflète bien l'état actuel de la technique.
Les renseignements relatifs à ce travail de révision, à l'éta- blissement des éditions révisées et aux mises à jour peuvent être obtenus auprès des Comités nationaux de la C E I et en consultant les documents ci-dessous :
O Bulletin de la C E I
O Annuaire de la C E I
O Catalogue des publications de la C E I
Publié annuellement
Terminologie
En ce qui concerne la terminologie générale, le lecteur se reportera à la Publication 50 de la C E I : Vocabulaire Electro- technique International (VEI), qui est établie sous forme de chapitres séparés traitant chacun d'un sujet défini, l'Index général étant publié séparément. Des détails complets sur le VE1 peuvent être obtenus sur demande.
Les termes et définitions figurant dans la présente publica- tion ont été soit repris du VEI, soit spécifiquement approuvés aux fins de cette publication.
Symboles graphiques et littéraux
Pour les symboles graphiques, symboles littéraux et signes d'usage général approuvés par la C E I, le lecteur consultera :
- la Publication 27 de la C E I : Symboles littéraux ?i utiliser en électrotechnique ;
- la Publication 617 de la C E I : Symboles graphiques pour schémas.
Les symboles et signes contenus dans la présente publication ont été soit repris des Publications 27 ou 617 de la C E I, soit spécifiquement approuvés aux fins de cette publication.
Publications de la C E I établies par le même Comité d'études
' L'attention du lecteur est attirée sur la page 3 de la couverture, qui énumère les publications de la C E 1 préparées par le Comité #Etudes qui a établi la présente publication.
Revision of this publication
The technical content of I E C publications .is kept under constant review by the I E C, thus ensuring that the content reflects current technology.
Information on the work of revision, the issue of revised editions and amendment sheets may be obtained from I E C National Committees and from the following I E C sources :
O I E C Bulletin
O I E C Yearbook
O Catalogue of I E C Publications
Published yearly
Terminology
For general terminology, readers are referred to I E C Publication 50 : International Electrotechnical Vocabulary (I E V), which is issued in the form of separate chapters each dealing with a specific field, the General Index being published as a separate booklet. Full details of the I E V will be supplied on request.
The terms and definitions contained in the present publica- tion have either been taken from the I E V or have been spe- cifically approved for the purpose of this publication.
Graphical and letter symbols
For graphical symbols, and letter symbols and signs ap- proved by the I E C for general use, readers are referred to :
- I E C Publication 27 : Letter symbols to be used in electrical technology ;
- I E C Publication 6 17 : Graphical symbols for diagrams.
The symbols and signs contained in the present publication have either been taken from I E C Publications 27 or 617, or have been specifically approved for the purpose of this publi- cation.
I E C publications prepared by the same Technical Committee
The attention of readers is drawn to the inside of the back cover, which lists I E C publications issued by the Technical Committee which has prepared the present publication.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
C O M M I S S I O N É L E C T R O T E C H N I Q U E I N T E R N A T I O N A L E
N O R M E D E L A C E 1
I N T E R N A T I O N A L E L E C T R O T E C H N I C A L C O M M I S S I O N
I E C S T A N D A R D
Publication 120 Troisième édition - Third edition
1984
Dimensions des assemblages à rotule et logement de rotule des éléments de chaînes d'isolateurs
Dimensions of ball and socket couplings of string insulator units
@ C E 1 1984
Droits de reproduction réservés - Copyright - all rights reserved
Aucune partie de celle publication ne peut être reproduite ni utilisée sous quelque forme que ce Soit et par aucun procédé,.élecîronique w mécanique, y compris la photocopie et les microfilms sans raccord émit de l'éditeur.
No part of this publication may be reproduced or utiïued in any form M by any mewis, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher.
Bureau Central de la Commission Electrotechnique Internationale 3, rue de Varembé
Genève, Suisse
P i ¡
Price Fr. s. 45. -
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC L20 8 4 W L184489L 0007879 L W
- 2 - 120 O CE1 1984
SOMMAIRE
Pages
P R É W U L E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Articles 1 . Domaine d?application . . . . . . . . . . . . . . . . . . . . . . . 6 2.Objet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 . Plandelanorme . . . . . . . . . . . . . . . . . . . . . . . . . 6 4 . Tigeàrotule . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 . Logement de rotule . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 . Calibre d?accrochage «PASSE» . . . . . . . . . . . . . . . . . . . . 8 7 . Partie inférieure de l?isolateur . . . . . . . . . . . . . . . . . . . . . 8 8 . Dispositif de verrouillage . . . . . . . . . . . . . . . . . . . . . . . 8 9 . Dimensions de la tige à rotule . . . . . . . . . . . . . . . . . . . . . 10
10 . Dimensions du logement à rotule . . . . . . . . . . . . . . . . . . . . 11 11 . Dimensions du calibre d?accrochage «PASSE» . . . . . . . . . . . . . . 12 12 . Dimensions des haltères . . . . . . . . . . . . . . . . . . . . . . . 14 13 . Jeu entre la tige à rotule et le logement de rotule . . . . . . . . . . . . . . 15 14 . Efficacité du verrouillage de la tige à rotule . . . . . . . . . . . . . . . . 16 15 . Dimensions du trou de logement de la goupille 17 16 . Dimensions du trou pour le logement de l?agrafe . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . .
ANNEXE A . Position de glissement et position de basculement de la tige à rotule dans le logement de rotule . . . . . . . . . . . . . . . . . . : . . 19
ANNEXE B . Calibres recommandés . . . . . . . . . . . . . . . . . . . 20
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984
CONTENTS
Page
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Ciause
1.Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2 .Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 3 . Plan of the standard . . . . . . . . . . . . . . . . . . . . . . . . 7 4.Pinball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 .Socket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 . Hook-on “GO” gauge . . . . . . . . . . . . . . . . . . . . . . . . 9 7 . Lower part of the insulator . . . . . . . . . . . . . . . . . . . . . . 9 8 . Lackingdevice . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9 . Dimensions of the pin ball . . . . . . . . . . . . . . . . . . . . . . 10
10 . Dimensions of the socket end . . . . . . . . . . . . . . . . . . . . . 11 11 . Dimensions of the hook-on “GO” gauge . . . . . . . . . . . . . . . . . 12 12 . Dimensions of twin-balled pins . . . . . . . . . . . . . . . . . . . . 14 13 . Clearance between the pin ball and the socket end 15 14 . Effectiveness of locking the pin ball . . . . . . . . . . . . . . . . . . . 16 15 . Dimensions of the hole for the split-pin . . . . . . . . . . . . . . . . . 17 16 . Dimensions of the hole for the W-clip 18
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . APPENDIX A . Sliding position and over-tilting position of the pin ball in the socket end . 19
APPENDIX B . Recommended gauges . . . . . . . . . . . . . . . . . . . 21
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 320 8L1 4844873 0007883 T
- 4 - 120 O CE1 1984
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
DIMENSIONS DES ASSEMBLAGES À ROTULE ET LOGEMENT DE ROTULE DES ÉLÉMENTS DE CHAÎNES D’ISOLATEURS
PRÉAMBULE
1) Les décisions ou accords officiels de la C E I en ce qui concerne les questions techniques, préparés par des Comités d’Etudes OÙ sont représentés tous les Comités nationaux s’intéressant à ces questions, expriment dans la plus grande mesure possible un accord international sur les sujets examinés.
2) Ces décisions constituent des recommandations internationales et sont agréées comme telles par les Comités nationaux.
3) Dans le but d‘encourager l’unification internationale, la C E I exprime le vœu que tous les Comités nationaux adoptent dans leurs règles nationales le texte de la recommandation de la CE I, dans la mesure OU les conditions nationales le permettent. Toute divergence entre la recommandation de la C E I et la règle nationale correspondante doit, dans la mesure du possible, être indiquée en termes clairs dans cette dernière.
PRÉFACE
La présente norme a été établie par le Sous-Comité 36B: Isolateurs pour lignes aériennes, du Comité
Elle remplace la deuxième édition de la Publication 120 de la CE I (1 977).
Le texte de cette norme est issu des documents suivants:
&Etudes no 36: Isolateurs.
I Règle des Six Mois I Rapport de vote
36B(BC)78 I 36B(BC)81 et 81A I
Pour de plus amples renseignements, consulter les rapports de vote mentionnés dans le tableau ci-dessus.
Les publications suivantes de la C E I sont citèes dans la prèsente norme:
Publications nos305 (1978): Caractéristiques des éléments de chaînes d’isolateurs du type capot et tige.
chaînes d’isolateurs - Dimensions et essais. 372 (1984): Dispositifs de verrouillage pour les assemblages à rotule et logement de rotule deséléments de
. 433 (1980): Caractéristiques des éléments de chaînes d‘isolateurs du type fut long.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 5 -
INTERNATIONAL, ELECTROTECHNICAL COMMISSION
Six Months’ Rule
36B(C0)78
DIMENSIONS OF BALL AND SOCKET COUPLINGS OF STRING INSULATOR UNITS
Report on Voting
36B(C0)81 and 81A
FOREWORD
1) The formal decisions or agreements of the I E C on technical matters, prepared by Technical Committees on which ali the National Committees having a special interest therein are represented, express, as nearly as possible, an international consensus of opinion on the subjects deait with.
2) They have the form of recommendations for international use and they are accepted by the National Committees in that sense.
3) In order to promote international unification, the I E C expresses the wish that all National Committees should adopt the text of the I E C recommendation for their national rules in so far as national conditions will permit. Any divergence between the I E C recommendation and the corresponding national rules should, as far as possible, be clearly indicated in the latter.
PREFACE
This standard has been prepared by Sub-Committee 36B: Insulators for Overhead Lines, of I E C
It replaces the second edition of I E C Publication 120 (1977).
The text of this standard is based upon the following documents:
Technical Committee No. 36: Insulators.
Further information can be found in the Reports on Voting indicated in the table above.
The following I E Cpublications are quoted in thk standard:
Publications Nos. 305 (1978): Characteristics of String Insulator Units of the Cap and Pin Type. 372 (1984) : Locking Devices for Ball and Socket Couplings of String Insulator Units - Dimensions and
433 (1980): Characteristics of String Insulator Units of the Long Rod Type. Tests.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 320 84 H 4844893 0007883 3 '
120 O CE1 1984 - 6 -
DIMENSIONS DES ASSEMBLAGES À ROTULE ET LOGEMENT DE ROTULE DES ÉLÉMENTS DE CHAÎNES D'ISOLATEURS
1. Domaine d'application
La présente norme est applicavl& aux éléments de c-aînes d'isolateurs du type capot et &e et LJ type à long fit, ainsi qu'aux accessoires métalliques utilisés avec de tels isolateurs.
2. Objet
La présente norme a pour objet de définir les dimensions d'une série d'assemblages normalisés pour les tiges à rotule et logement de rotule utilisant les dispositifs de verrouillage normalisés (voir Publication 372 de la CE I : Dispositifs de verrouillage pour les assemblages à rotule et logement de rotule des éléments de chaînes d'isolateurs), de façon à rendre possible l'assemblage d'isolateurs ou d'accessoires métalliques provenant de constructeurs différents. Note. - Cette norme ne définit que les dimensions nécessaires à l'assemblage. Les propriétés de la matière et les charges
de service ne sont pas spécifiées. La coordination des dimensions avec les classes d'efforts est spécifiée dans les Publications 305 de la C E I : Caractéristiques des éléments de chaînes d'isolateurs du type capot et tige, et 433 de la C E I : Caractéristiques des éléments de chaînes d'isolateurs du type fut long.
3. Plan de la norme
La présente norme comprend six normes d'assemblage définies par les diamètres de tiges nominaux qui constituent la base de la norme. Chaque norme d'assemblage est définie par les dimensions de la tige à rotule, du logement de rotule et du calibre d'accrochage «PASSE>> spécifiées dans les articles 9 à 1 1. Les dimensions des haltères pour la liaison de deux logements de rotule sont indiquées dans l'article 12. Le jeu et les conditions de verrouillage sont groupés dans les tableaux des articles 13 et 14. Les dimensions du trou pour le logement du dispositifde verrouillage sont indiquées dans les articles 15 et 16.
Toutes les dimensions sont exprimées en millimètres.
Pour la tige à rotule et le logement de rotule, les dimensions s'appliquent au produit hi après
L'annexe A donne les positions limites de la tige à rotule dans l'intérieur du logement de
L'annexe B donne des exemples typiques de calibres de vérification pour les dimensions des
application éventuelle de tout traitement superficiel.
rotule.
tiges à rotule et les logements de rotule.
4. Tige à rotule
La tige à rotule doit être conforme aux dimensions spécifiées dans l'article 9. Les principales dimensions déterminant la forme de la rotule sont hi, d2, ri et r2. La dimension r3 est donnée à titre indicatif, car sa valeur exacte ne peut être obtenue que par la construction géométrique. En outre, le diamètre de la tige à rotule di ne doit pas dépasser les valeurs spécifiées sur une longueur égale à H3 du calibre d'accrochage correspondant a PASSE >> usé (voir article 11).
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 7 -
COUPLINGS ~ -
1. Scope
This standard applies to string insulator units of the cap and pin and long rod types and their associated metal fittings.
2. Object
The object of this standard is to define the dimensions of a series of standard ball and socket couplings using the standard locking devices (see I E C Publication 372 : Locking Devices for Ball and Socket Couplings of String Insulator Units) in order to permit the assembly of insulators or metal fittings supplied by different manufacturers. Note. - Oníy the dimensions necessary for assembly are dealt with in this standard. Properties of material and working
loads are not specified. The co-ordination of dimensions with strength classes is specified in I E C Publications 305 : Characteristics of String Insulator Units of the Cap and Pin Type, and 433 : Characteristics of String Insulator Units of the Long Rod Type.
3. Plan of the standard
This standard includes six standard sizes designated by the nominal pin diameters which form the basis of the standard. Each standard size is defined by the dimensions of the pin ball, of the socket and of the hook-on “GO” gauge specified in Clauses 9 to 1 1. Dimensions of twin-balled pins for coupling of two sockets are stated in Clause 12. Clearance and locking conditions are tabulated in Clauses 13 and 14. Dimensions of the hole for the locking device are stated in Clauses 15 and 16.
All dimensions are expressed in millimetres.
For the pin ball and the socket, dimensions apply to the finished product after any surface
Extreme positions of the pin ball in the socket are given in Appendix A.
treatment.
Typical examples of-gauges for checking the dimensions of pin balls and sockets are given in Appendix B.
4. Pin ball
The pin ball shall conform to the dimensions specifled in Clause 9. The main dimensions governing the shape of the pin ball are hl, d,, rl and r,. Dimension r, is given for guidance because its accurate value may be obtained only by the drawing. In addition, the shank diameter d,, must not exceed the specified values within a length equal to H3 of the corresponding worn hook-on “GO” gauge (see Clause 11).
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 320 8 4 4844873 0007885 7
- 8 - ..
5. Logement de rotuie
120 O CE1 1984
L’intérieur du logement de rotule doit être conforme,aux dimensions spécifiées dans l’article 10, qui indique également la hauteur minimale du dispodif de vgrro-dage.
- -_ Notes 1. - Les logements de rotule, conformes à l’article précité, présentent un fond plat sur les dessins. il est également
possible d‘utiliser des logements de rotule à fonds arrondis dont les rayons de courbure ne sont pas inférieurs aux dimensions r, des tiges à rotule. Dans ce cas, les dimensions R, doivent être diminuées de façon correspondante.
2. - La dimension normalisée de 16 mm selon l’article 10 comprend deux solutions pour le logement de rotule, parce qu’il est nécessaire de prévoir, d’une part, un logement de rotule convenant exactement à la tige à rotule normalisée et aux tiges des normes antérieures avec rl = 23 (solution A) et, d’autre part, un logement de rotule pouvant également recevoir des tiges à rotule de tZ = 50 (solution B). ia solution A et la solution B sont identiques, sauf pour les dimensions H,, H, et T, ia solution A, qui comporte des dimensions plus faibles, est préférable dans les cas OU l’assemblage faisant usage des tiges à rotule existantes n’exige pas l’utilisation de la solution B.
6. Calibre d’accrochage a PASSE ))
Les dimensions extérieures du logement de rotule n’ont pas été déterminées. L’extérieur du logement de rotule doit, cependant, permettre ¡e passage du calibre d‘accrochage <( PASSE B conforme à l’article 11.
7. Partie inférieure de l’isolateur
La forme de la partie inférieure de l’isolateur doit être telle qu’il soit toujours possible d‘ac- crocher à cet isolateur un logement de rotule ayant des dimensions extérieures maximales con- formes à l’article 6.
8. Dispositif de verrouillage
Le dispositif de verrouillage, c’est-à-dire la goupille ou l’agrafe, doit être conçu de façon à pouvoir verrouilier la tige à rotule minimale dans le logement de rotule maximal. Cette condition est remplie en utilisant les dispositifs de verrouillage normalisés dans la Publication 372 de la CEI.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 9 -
5. Socket
The socket interior shall conform to the dimensions specified in Clause 10, which also specifies the minimum thickness of the locking device.
Notes 1. - Sockets according to the clause mentioned are shown with flat bottoms. Sockets with rounded bottoms with radii ofcurvature not less than the dimensions rz ofthe pin b d s canais0 be used. in this case, the dimensions R, have to be correspondingly decreased.
2. - The 16 mm standard size according to Clause 10 includes two alternative sockets. The reason for this i s that, on the one hand, there is a need for a socket fitting exactly the standard pin ball and its predecessors with r, = 23 (alternative A) and, on the other hand, there is a need for a socket also accepting pin baiis with rz = 50 (alternative B). Alternative A and alternative B are identical except for dimensions H,, H, and T. Alternative A, having the smder dimensions, is preferable where assembly with existing pin b d s does not require alternative B.
6. Hook-on “GO” gauge
The external dimensions of the socket have not been laid down. However, the socket shall permit acceptance of the hook-on “GO” gauge according to Clause i 1.
7, Lower part of the insulator
The shape of the lower part of the insulator shall be such that assembly with the socket of maximum external dimensions according to Clause 6 will always be possible.
8. Locking device
The locking device, i.e. a split-pin or W-clip, shail be designed for locking the minimum-size pin bali in the maximum size socket. This requirement is fulfilled if the locking devices standardized in I E C Publication 372 are used.
. - . . ~
. ..
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
- 10 - 120 O CE1 1984
9. Dimensions de la tige à rotule
Dimensions of the pin baii
181177
Désignation de l’assemblage Designated size
of coupling
dl
O 21-1,3
2 9 3 5
32 * Donné à titre indicatif.
Given for guidance.
33-?,6
r3* r4
3,5 1,5+:
3 32 ,5
5,7 3 9 ;
6 6 - l,o 4+ 1,s
4 5+ 13 ’ -l,o
5+ 1,s
8
10 -l,o
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 11 -
10. Dimensions du logement à rotule
Dimensions of the socket end .
7-
I I
I l 183177 182177
11, 16A, 24, 28, 32 Assemblage coupling
goupilles norma- lisées
R,
standard split-pins I Min.
H, POW
agrafes et
variantes de
goupilles for
w-clips and
iltematiw split-pins
Min.
Désignation de l'assemblage Designated size
of coupling 4
Min.
D3 Hi
Min.
11 12,5+k3 24,5 15,5 16,3 I 35
16 A') 19,2+ k6 343 20,5 21,6 I 23
16 B') 343 25
20 23+$' 42,5 42,5 I 20,5+$' 28,5
24
28
51
59
67,5
32,5
36,5
42
37,4
43 70 32 36+ 3.3 O
1) Voir la note 2 de l'article 5. See Note 2 of Clause 5.
2) Hauteur du dispositif de verrouillage. Thickness of the locking device.
3) On donne une valeur plus grande parce que, dans ce cas, la goupille ne repose pas toujours sur le fond du logement de rotule. La position de la goupille normalisée est déterminée parla positionH3 du centre du trou, par son diamètre D4 (voir article 15) et par la dimension I;, (voir Publication 372 de la C E I) ; elle est aussi influencée par les extrémith des branches restant en contact avec le logement de rotule. Les valeurs de H, assurent un jeu correct pour les goupilles. A greater value is given because in this case the split-pin does not always rest on the bottom of the socket. The position of the standardsplit-pinisdeterminedbythe positionif, ofthecentreofthe holeandits diameterD4 (see Clause 15)anddimensionF, (see I E CPublication 372) and is also influenced bythe tips ofthe legs resting in contact with the socket. The values ofH, ensure the correct clearances for split-pins.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 320 8 4 a 4844873 O007889 4 I
- 12 - 1 1, Dimensions du calibre d’accrochage << PASSE N
Dimensions of the hook-on “GO” gauge
120 O CE1 1984
184177
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
- 13 - 120 Q IEC 1984
I L. a 3 L2
L
O c1
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
12. Dimensions des haltères
Dimensions of twin-balled pins
ias177
- 14 - 120 O CE1 1984
de l’assemblage Designated size
47-35 I 11 I
I 120-s,0 I 32
Pour les autres dimensions, voir l’article 9.
For other dimensions, see Clause 9.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
P
186177 187177
ia tige à rotule se trouve dans l'entrée du logement de rotule.
The pin bail in the socket entry.
La tige à rotule se trouve à Pintérieur du logement de rotule.
The pin ball in the socket interior.
Désignation de l'assemblage Designated size ofco;hg
16A I 2,2
16B I 2,2
28 I 3,o
Max.
3,O
5,o
794
739
1) Jeu entre la tige et le dispositif de verrouillage. Clearance between the pin ball and the locking device.
235
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 120 8 4 m 484487i 0007873 b m '
- 16 -
14. Efficacité du verrouillage de la tige à rotule
Effectiveness of locking the pin bail
T
t 188177
hauteur minimale du dispositif de verrouillage minimum thickness of the locking device
efficacité du verrouillage
=
' = effectiveness of locking
Désignation de l'assemblage Designated size
of coupling
I I 11
I I 16 A 1 3
32 393
120 O CE1 1984
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 120 8 4 W 4844891 0007894 8 ~ _ _ _ ~ __=~ = =-=- ~
20
24
120 O I E C 1984 - 17 -
10 f 0,5 18,O 5+ O 1 2 5 f 1 40
12 f 0,5 21,5 6+ O 135 6 f 1 51
15. Dimensions du trou de logement de la goupiiie
Dimensions of the hole for the split-pin
.Axe de I'assem blaae Section XX Axis of the coupling
Section YY
EXEMPLE 1 EXAMPLE 1
Section YY
EXEMPLE 2a EXAMPLE 2a
Section YY
EXEMPLE 2b EXAMPLE 2b
230/84
H3
Assemblages normalisés Standard couplings
0 4
Min. Min. Max.
I 24 7,5 f 0,4 3,75+ 3,5 +- 0,6
l1 I I 32
16A I 9,5 f 0,5 I 16,O I 4,75+; I 4 f 0,7
16B I 10 f 0,5 I 18,O I 5+: 1 5 f 1 I 32
I 59 13 f 0,5 I 24,O I 6,5+i5 I I f 1,2
I 15 f 0,5 1 28,O I 7,5+i5 I 8 f 1,4 32 I
Les dimensions sont valables pour les goupilles normalisées et les variantes de goupilles
The dimensions are applicable to both standard and alternative split-pins (see I E C Publi-
(voir Publication 372 de la C E I).
cation 372).
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 1 2 0 84 m 4B4489L 0007895 T m
Assemblages normalisés Standard couplings
- 18 - 120 O CE1 1984
16. Dimensions du trou pour le logement de l’agrafe
Dimensions of the hole for the W-ciip
L B2 B, H3
Min. Max. .
I I I
16 B
Axe de l’assemblage Axis of coupling
.-. J
16 f 1 33 9,5 f 0,8 24
I Section XX
20
24
231/84
17 f 1 34 8,5 f 0,8 29
17,5 f 1 343 10,5 f 0,8 34
32
I I 11 I 12,5 f 0,8 I 24 I 6,5 f 0,8 I 18
22 f 1 42 13,O f 0,8 48
I 24 I 33 I I 16A I I 7 f 0,8 16 f 1
I 20 f 1 I 39 I 11,5 f 0,8 I 42 I I 28
La dimension B, est la longueur du logement pour laquelíe la hauteur H3 doit être main-
Au-delà de B2, la forme du logement n’est pas importante. Dimension B, is the length of the recess over which the height H3 shall be maintained. Beyond B,, the shape of the recess is not important.
tenue.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 6 I E C 1984
Désignation
ANNEXE A APPENDIX A POSITION DE GLISSEMENT ET POSITION SLIDING POSITION AND OVER-TILTING
DE BASCULEMENT DE LA TIGE A ROTULE DANS LE LOGEMENT
DE ROTULE
POSITION OF THE PIN BALL IN THE SOCKET END
a'
Al. Position de glissement de la tige à rotule dans le logement de rotule Sliding position of the pin ball in the socket end
de l'assemblage Designated size
of coupling lUO!- I I
moyen average
189177
11 1,3 I 16 A 420 I
32 2,O I A2. Position de basculement de la tige à rotule dans le logement de rotule
Over-tilting position of the pin ball in the socket end
T
190177
de i'assemblage Designated size
of coupling
Fi) moyen average
12,o I 16 B I
Les valeursß correspondent à des tolérances raisonnables de H,. ß values assume reasonable tolerances for H,.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
I E C 320 84 a 4844873 0 0 0 7 8 7 7 3
- 20 -
ANNEXE B
120 O CE1 1984
CALIBRES RECOMMANDÉS
B1. Système de tolérances
Les tolérances pour les calibres sont conformes au système ISO. Cela signifie que les calibres << NE PASSE PAS >> n'ont que des tolérances de fabrication qui sont situées symétriquement par rapport à la limite de tolérance correspondante de la pièce faisant partie de l'assemblage à rotule et logement de rotule. Cela signifie également que les calibres << PASSE D ont des marges d'usure et des tolérances de fabrication qui sont comprises dans le champ de tolérance de la pièce faisant partie de l'assemblage à rotule et logement de rotule. Note. - Pour les calibres a PASSE », chaque pays est libre d'utiliser les marges d'usure pour augmenter les tolérances de
fabrication proposées. Les calibres ayant subi une usure au-delà des limites prescrites pour les calibres usés ne seront plus utilisés.
B2. Exécution des cagbbres
Le choix des matières, la dureté, le finissage des surfaces, le traitement des surfaces et le procédé de fabrication sont susceptibles de varier d'un pays à l'autre. Par conséquent, les recommanda- tions suivantes ne sont données que comme indications générales : - l'épaisseur des calibres pour les tiges à rotule ne sera pas inférieure à 5 mm ; - l'épaisseur des calibres à trou rond sera un peu plus forte ; - la matière sera un acier trempé à l'huile, sans retrait ; - le nombre de dureté Rockwell C sera de 62 à 63, afin de réduire les déformations et
- la rugosité des surfaces sera inférieure à 4 pm ; - dans certains cas, le chromage dur peut augmenter la résistance à l'usure. Note. - Les calibres pour les logements de rotule seront pourvus d'une partie rectifiée sur le diamètre D, ou de trous de
centrage, afin de faciliter le contrôle des calibres. Un trou de centrage enlève une partie de la surface courbe, ce qui réduit la tolérance de fabrication.
l'usure ;
I
Tige I
l Rotule
a) La rotule et la tige doivent passer, dans une direction au moins, à travers le calibre a PASSE >>
b) La rotule doit passer dans le calibre G PASSE >> de diamètre de rotule (voir article B6). c) La rotule et la tige ne doivent passer, dans aucune direction, dans le calibre a NE PASSE PAS >>
d) La rotule ne doit passer, dans aucune direction, dans le calibre a NE PASSE PAS >> de diamètre
e) La tige ne doit entrer, dans aucune direction, dans le calibre a NE PASSE PAS >> de diamètre de
de hauteur de rotule, de diamètre et de longueur de la tige (voir article B5).
de hauteur de rotule (voir article B7).
de rotule (voir article B8).
la tige (voir article B9). ti
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 21 -
APPENDIX B RECOMMENDED GAUGES
B 1. Tolerance system The tolerances for the gauges follow the IS0 system. This means that the “NOT GO” gauges
oniy have manufacturing tolerances which are symmetrically located in relation to the corre- sponding tolerance limit of the coupling part. It also means that the “GO” gauges have allowances for wear and manufacturing tolerances which fall within the tolerance zone of the coupling part.
Note, - For “GO” gauges it is left to the choice of each country to use the allowance for wear to increase the proposed manufacturing tolerances. Gauges which have been worn beyond any of the limits given for worn gauges should not be used.
B2. Constructional features of the gauges The choice of material, the hardness, the surface finish, the surface treatment and the method of
manufacture are liable to vary from one country to another. Therefore, the following recommen- dations are given only for general guidance : - the thickness of the pin gauges should be not less than 5 mm ; - gauges provided with round holes should be somewhat thicker ; - the material should be a non-shrinking, oil-hardenhig steel ; - the Rockwell C hardness number should be 62 to 63 in order to reduce deformations and
- the surface roughness should be less than 4 p ; - hard chromium plating can, in certain cases, increase resistance to wear. Note. - The socket gauges should be provided With a ground shaft, diameter DI, or with centre holes in order to facilitate
checking of the gauges. A centre hole removes part of the curved surface, and this reduces the manufacturing tolerance.
wear ;
Shank I
I Ball
a) Ball and shank shall pass in at least one direction through “GO” gauge for ball height, shank
b) Ball shall pass through “GO” gauge for ball diameter (see Clause B6). c) Ball and shank shall not pass in any direction through “NOT GO” gauge for ball height (see
d) Bali shall not pass in any direction through “NOT GO” gauge for ball diameter (see Clause
e) Shank shall not enter in any direction through “NOT GO” gauge for shank diameter (see
diameter and shank length (see Clause B5).
Clause B7).
B8).
Clause B9).
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 320 84 4844873 0007877 7 = 8
- 22 - 120 O CE1 1984
B4. Contrôle du logement de rotule
192177
a) L'entrée du logement de rotule doit accepter le calibre a PASSE B pour la hauteur, la largeur de l'entrée et la largeur d'ouverture (voir article B10).
b) La hauteur et le diamètre intérieurs du logement de rotule doivent permettre une rotation de 180", à l'intérieur du logement de rotule, du calibre a PASSE N de diamètre et hauteur intérieurs (voir article B1 1).
c) La hauteur de l'entrée du logement de rotule ne doit pas permettre l'entrée du calibre a NE PASSE PAS D pour la hauteur de l'entrée (voir article B12).
d) L'entrée du logement de rotule ne doit pas permettre l'entrée du calibre << NE PASSE PAS D pour la largeur de l'ouverture (voir article B13).
Note. - Le tracé marqué (- - - - - - - -) doit laisser passer le calibre d'accrochage << PASSE D (voir article 1 1).
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 0 I E C 1984 - 23 -
B4. Checking the socket end
192177
a) Socket entry shall accept “GO” gauge for entry height, entry width and neck width (see Clause
b) Internal height and internal diameter of socket shall allow rotation through 180” inside the
B10).
socket of the “GO” gauge for internal height and internal diameter (see Clause B 1 1).
c) Socket entry height shall refuse the “NOT GO” gauge for entry height (see Clause B12).
d) Socket entry shall refuse “NOT GO” gauge for neck width (see Clause B13).
Note. - Marked contour (---------) to accept hook-on “GO” gauge (see Clause 11).
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
22,712
22,728
22,744
22,800
33,204
33,222
33,240
33,300
40,900
40,920
40,940
41,000
48,890
48,912
48,934
49,000
56,881
56,905
56,929
25,5
25,O
24,5
24,O
3 5 3
35,O
34,5
34,O
45,5
45,O
443
44,O
50,5
50,O
493
49,O
68,5
68,O
67,s
22,952
22,960
22,968
23,OOO
26,950
26,959
26,968
49,952
49,960
49,968
50,000
59,950
59,959
59,968
13,336
13,400
19,400
19,418
19,436
19,500
20,888
20,908
20,928
21,000
23,380
23,402
23,424
32,06
32,OO
42,64
42/50
42,56
42,50
4665
46,61
46,57
46,50
51,66
51,62
51,58
2,959
2,993
5,703
5,711
5,719
5,753
6,558
6,567
6,577
6,615
7,803
7,814
7,825
7,864
4,029
4,000
4,542
4,536
4,530
4,500
5,544
5,538
5,532
5,500
6,044
6,038
6,032
6,000
Usé 2) -Worn 2) 17,000
39,944
39,954
39,964
40,000
54,940
54,951
54,962
55,000
69,934
69,946
69,958
70,000
69,944
69,954
69,964
70,000
79,940
79,951
79,962
80,000
89,934
89,946
89,958
90,000
Neuf New
I
28,919 Contour nominal Nominal contour
IEC 120 A4 m 4844871 OR07901 1 m
- 24 - 120 O CE1 1984
B5. Calibre de la tige à rotule «PASSE» pour la hauteur de la rotule, le diamètre de la tige et la longueur de la tige
Pin “GO” gauge for bali height, shank diameter and shank length
45 rt
PASSE
GO 4
193177
Désignation de l’assemblage
Designated size of coupling I dl
Calibre -Gauge
dz I d4 Ili I I’, I
11,826 Contour min. I Min. contour 1) 3,509 2,537
3,517 2,532
3,525 2,521
3,556 2,500 c 2,945 4,039
I 11,836 Neuf Contour nominal New I Nominal contour 11
Contour max. I Max. contour I) I 11,846
Usé 2) - Worn 2) I 11,900
16,922
16,932
16,942
1 %%n% 1: 1 Neuf Contour nominal New Nominal contour
Contour max. Max. contour
13,304 I 32,14
13,320 I 32,lO 2,952 I 4,034 16
20,9 I6
20,928
Contour min. I Min. contour I Neuf Contour nominal New Nominal contour 20
I 20,940 Contour max. I Max. contour I)
Usé 2) -Worn 2) I 21,000 27,000 I 60,000
24,912
24,924
24,936
Contour nominal Nominal contour Contour max. Max. contour
24
. Usé 2) -Worn 2) I 25,000
I 28,906 Contour min. I Min. contour I)
28 I 28,932 Contour max. I Max. contour
Usé 2) - Worn 2) I 29,000 57,000 67,O
64,871 87,5
64,897 87,O
64,923 86,5
55L000 t 86,O
23,500 51,50
26,868 62,16
26,892 62,12
26,916 62,08
27,000 t 62,OO
32,899
32,913
Contour min.
Contour nominal New . Nominal contour
9,506 6,544 + 9,517 6,538 32 I Contour max. I M=. contour I) I 32,927 9,528 6,532
G+G- Usé 2) - Worn 2) I 33,000
I) Le contour du caiibrc ncuf doit Ctrc compris entre les conioun minimal et maximiil. ‘Tho contour of the new gauge shall fall bciwccn the minimum and maximum contours.
2) Voir l’article 131. Sec Clause H I .
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 120 B q qBq4891 0007902 3
Worn 1)
120 O I E C 1984 - 25 -
33,300
B6. Calibre de la tige à rotule a PASSE n pour le diamètre de la rotule
Pin “GO” gauge for ball diameter
usé ,) Worn
194177
41,000
Désignation de l’assemblage Designated size
of coupling
Usé Worn 1)
11
57,000
16
Worn 1)
20
65,000
24
28
32
Neuf New 22,728 i 0,011
33,223 f 0,012 Neuf New
Neuf New 40,920 i 0,013
Neuf New I 48,913 f 0,014
Neuf New 56,908 f 0,015
Neuf New 64,903 f 0,016
1) Voir l’article B 1. See Clause B1.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
36,9
37,O
37,l
40,88
41,OO
47,3 32,3 21,678
47,O 32,O 2 1,700
46.7 31,7 21,722
52.3 363 25,076
52,O 360 25,100
IEC 1 2 0 8 4 M 4 8 4 4 8 9 1 0007703 5 M
- 26 - 120 O CE1 1984
B7. Calibre de la tige à rotule << NE PASSE PAS N pour la hauteur de la roNe
Pin “NOT GO” gauge for ball height
t 4 i
195177
Désignation de !‘assemblage
Designated size of coupling
Calibre -Gauge
1608 1 8 , 6 0 I 12,3 I 7,884 I L5,5 I 34,992 I 3,7 Contour min. Min. contour ’)
16,lO I 18,40 I 12,O I 7,900 I 16,O I 35,000 I 4,O Contour nominal Nominal contour 11 Contour max. Max. contour 16,l2 I 18,20 I IIJ I 7,916 I 1 6 5 I 35,008 I 4,3
Contour min. Min. contour I) 23,66 I 30,3 I 18,3 I 12,084 I 21,5 I 22,992 I 4,7
Contour nominal Nominal contour 12,100 23,000 ::j 12,116 23,008
18,082 26,991
18,100 30,O 27,000 7.0
16 23.70
23,74
28,36 23,3
28,42 36,O 23,O
Contour m a . Max. contour I) Contour min. Min. contour I)
Contour nominal Nominal contour 20
24
Contour n i a . Max. contour
~
Contour min. Min. contour I) 34,48 I 42,3 I 28,3 I 19,280 I 31,5 I 39,990 I 7,7
Contour nominal Nominal contour 34,54 I 42,O I 28,O I 19,300 I 32,O I 40,000 I 8,0
Contour max. Max. contour 34/50 I 41,7 I 27,7 I 19,320 I 32,s I 40,010 I 8,3
Contour min. Min. contour I) 54,989
55,011
47,5 69,988 i 1,7
Contour nominal Nominal contour 28 Contour max. Max. contour I) Contour min. Min. contour I) Contour nominal Nominal contour 48.0 I 70,000 I 12,O 32 Contour max. Max. contour
1) Le contour du calibre doit être compris entre les contouts minimal et maximal. The contour of the gauge shall fall between the minimum and maximum contours.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 27 - B8. Calibre de la tige à rotale <c NE PASSE PAS D pour le diamètre de la rotule
Pin “NOT GO” gauge for ball diameter
Désignation de l’assemblage Designated size
of coupling 4
10,800 20,009
15,800 +0,010
11
16
L d 2 I
~~
4 h4 h5
15,O 12,O 1,0 i0,5 +0,5 f0 ,3
20,O 15,O 1,0 f0,5 2 4 5 +0,3
I NE PASSE PAS
NOT GO
23,600 f0,012 24
196177
30,O 23,O 1,0 2 4 5 f0,5 f0,3
Désignation de l’assemblage Designated size 4
of coupling
21,500 f 0,011
31,800 +0,012
11
16
2o I f0,013 39y400
47,200 i 0,014
55,100 +0,015
62,900 t0,016
24
28
32
I
B9. Calibre de la tige à rotule NE PASSE PAS )> pour le diamètre de la tige
Pin “NOT GO” gauge for shank diameter
¡NE PASSE PA!
NOT GO
197177
h4
10,o +0,5
12,o +0,5
18,O f0,5 -
20,o f 0,5
22,o f 0,5
25,O f 0,5
h5
120 f 0,3
1,O f 0,3
4 5 f 0,5
45 f0,5
135 :0,58
I I I- l I 19,700 1 25,O I 18,O 1 1,0 20,012 +0,5 t0,5 +0,3 20
l I I
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
- 28 - 120 O CE1 1984
B10. Calibre du logement de rotule a PASSE 1) pour la hauteur de l’entrée, la largeur de l’entrée et la largeur de l’ouverture.
Socket “GO” gauge for entry height, entry width and neck width
1
11, 16A, 24 Assemblage coupling
- 199177
198177
Assemblage 16 B, 20, 28, 32 coupling
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O I E C 1984 - 29 -
Désignation de l'assemblage
Designated size of coupling I Calibre - Gauge Hi Ri R3 Ro RS
1,458 -
1,464 -
1,470 - 1,500 -
2,953 - 2,960 -
2,967 -
3,000 -
2,953 3,051
Hs
30,s
30,O
29,s
24,590 10,596
10,580
10,564
- -
35,048
35,040
35,032
-
-
4,222
4,213 -
35,048
35,040
35,032
- 12,584
12,572
12,560
12,500 Usé 3) - Worn 3)
24,578
24,566 - 11
4,205
24,500 10,500 3 5 , w 35,000 4,173 29,O
40,s
16 A 2,
I Contourmax. i) I 19,294
19,280
Max. contour
Neuf Contour nominal New Nominal contour
34,602 14,608 23,054 50,054 3,338
34,588 14,588 40.0 23,044 50,044 3,325
I 19,266 Contour min. I . Min contour I' 34,574 14,568 39,s 23,034 50,034 3,311
Usé 3) -Worn 3) I 19,200 34,500
34,602
34,588
- -
14,500
17,108
17,088
- -
50,000
50,054 -
3,281
3,051 -
2 3 , m
23,054
23,044
- 39,O
40,s
40,O 50,044 3,044 2,960 I 3,044 19,280
19,266 16 B 2 )
34,574 17,068 39,s 23,034 50,034 3,037 2,967 3,037 .& I l
Usé 3) -Worn 3) 19,200 34,500 17,000 39,O 23,ooC 50,000 3,000
20
42,630 20,632 50,s 27,066 60,066 6,065 3,442 I 5,565 Contour max.
23,098 42,610 20,606 50,o 27,053 60,053 6,055
I 23,080 Contour min. I Min. contour ') 42,590 20,580 49,s 27,04(
27,M
40,07f
40,061
- - __
60,040 6,045
6 -
- 7,898
Usé 3) -Worn 3) I 23,000 ' 42,500 20,500 60,000
70,076
70,061
-
-
49,O
55,s
55,o
27,630
27,610
Contour max. Max. contour ') I 1 Neuf Contour nominal
New Nominal contour
51,150
51,126
51,102
- -
23,652
23,622 -
7,881
24 I
27,590 Contour min. Min. contour I) 23,592 54.5 40,04t 70,046 7,864 3,955
Usé 3) -Worn 3) I 27,500 51,ooo 23,500 70,00(3 7,821 54,O
60,s 32,144
32,122
Contour max. I Max. contour i) I Neuf Contour nominal New Nominal contour
59,166 26,170 55,08f 80,085 8,083
8,069
8,055
8,000
- -
-
59,138 26,135 55,06;
55,OSí
55 ,m
70,09!
- - -
80,068
80,050
80,000
-
-
60,O
59,s
59,O
70,s
28 32,100 i Min. contour 1 32,000
36,158
Contour min.
Usé 3) - Worn 3)
Contour max. Max. contour
59.1 10
59,000
67,680
- -
26,100
26,000
30,190
- -
90,095 10,090 4,923 11,890 + 4,935 11,875 I
36,134 Neuf Contour nominal New Nominal contour 67,650 30,150 70,O 70,07! 90,075 10,075
32 Contour min. t Min. contour '1 I 36,110 67,620 30.1 IO 70,OSf 90,055 10,060 4,947 I 11,860 69.5
69,O Usé 3) - Worn 3) I 36,000 67,500 30,000 70,W 90,000 10,ooo 5,000 I 11,800
i) Le contour du calibre neuf doit être compris entre les contours minimal et maximal. The contour of the new gauge shall fall between the minimum and maximum contours.
2) Voir la note 2 de L'article 5. See Note 2 of Clause 5.
3) Voir L'article BI. See Clause BI.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
-30- 120 O CE1 1984
B11. Calibre du logement de rotule << PASSE D pour la hauteur intérieure et le diamètre intérieur
Socket “GO” gauge for internal height and internal diameter
‘I I I l-
200177
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O IEC 1984 - 31 -
-
D3
- 24,590
-
Ri
Désignation de l'assemblage
Designated size of couvlina
H z H24) avec goupille
agrafe normale R3 R5 Calibre - Gauge with
\v-clip ~
15,596
tsndard plit-pin
16,396 -
Contour may.
Neuf New Nominal contour
Min. contour
12,584 30.5 35,048 35,048 4,045 1,458 4,045
12,572 24,578 15,580 16,380 30,O 35,010 35,040 4,039 1,464 4,039
4,033 ~ I l
12,560 24,566 15,564 16,364 29,s 35,032 35,032 4,033 1,470
Usé 3) -\Vom 3) 12,500 24,500 15,500 16,300 29,O 35,000 35,000 4,000 1,500 4,000
Contour max. Max. contour I Neuf Contour nominal
New Nominal contour
19,294 34,602
34,588
34,574
-
-
20,608
20,588
20,568
-
-
21,708
21.688
21,668
-
-
40,s
40.0
39.5
-
-
23,054
23,044 -
50,054
50,044 -
3,051
3,044 ~
2,953
2,960 ~
3,05 I
3,044 ~
19,280
19,266 - 16 A 2,
23,034 50,034 3,037 2,967 3.037 Contour min. Min. contour I)
Usé 3) -\Vorn 3) 19,200 34,500 20,500 21,600 39,O 23,000 50,ooO 3 ,000 3,000 3,000
Contour max. I Max. contour Neuf Contour nominal New Nominal contour
19,294 34,602 25,108 25,608 40,s 23,054 50,054 3,051 2,953 3,051
19,280 34,588 25,088 25,588 40,O 23,044 50,044 3,044 2,960 3,014
16 B 2, Contour min. I hfin. contour I) 19,266 34,574 25,068 25,568 39,s 23,034 50,034 3,037 2,967 3,037
19,2W 34,500 25,000 25,500 39.0 23,000 50,000
60,066
60,053
60,040
-
~
-
3,ow
6,065
6,055
6,045
-
~
-
3,000
3,442
3,451
-
-
3,000
6,065
6,055
-
-
Usé 3) -\Vorn 3)
Contour max. Max. contour I) 23,116
23,098 -
~
23,080
42,630
42,610
42,590
-
~
28,632
28,606
28,580
-
-
29,432
29,406
29,380
-
-
50,s
50,O
4 9 s
~
-
27,066
27,053
27,040
~
- Neuf New
Contour nominal Nominal contour Contour min. Min. contour I)
20 3,460 6,045
Usé 3) -Worn 3) 23,000 42,500 28,500 29,300 49,O 27,000 60,000 6,000 3,500 6,000
8,075 ~
Contour max.
Neuf New E Nominal contour
Min. contour
27,63C 51,150 32,652 33,652 55,5 40,076 70,076 5,075 3,935
27,61C 51,126
51,102 -
~
51,000
59,166
59,138
59,110
59,000
-
~
~
~
32,622 33,622 55,o 40,061 70,061 5,063 3,945 8,063
24 27,59C 32,592 33,592 54,s 40,046 70,046 5,051 3,955 8,05 I
Usé 3) -Worn 3) 27,SGí 32,500 54,O 40,000 70,000
80,085
80,068
-
-
5,ow
8,083
8,069
-
-
4.000
4,429
4.440
-
-
8,000
8,083
8,069
-
-
33,500
37,570
37,535
37,500
~
~
- 37,400 - 43,190
43,150
43,110
43,000
-
-
~
32,144
32,122 -
36,670
36,635 ~
60,s
60,O ~
55,085
55,067 -
Nominal contour Contour min. Min. contour
28 32,10( 36,600 59.5 55,050 80,050 8,055 4,45 I 8,055
Usé 3) -Worn 3) 32,OOC 36,500 59,o 55,000 80,000 4,500 8,000
Contour max. ~~f I Max. contour 1
Contour nominal Nominal contour Contour min. Min. contour
Usé 3) -Worn 3)
36,158 67,680
67,650
67,620
67,500
-
-
-
-
42,190 70,s 70,095
70,075 ~
90,095 10,09c 4,923 10,090
36,134 42,150 70,O 90,075 10,075 4,935
4,967
5,000
-
~
10,075 - 10,060
10,ooo ~
32 42,l IO
42,000 -
69.5
69,O ~
70,055
70,000 ~
90,055
90,000 ~
l0,06C
I0,ooC ~
I) Le contour du calibre neuf doit être compris entre les contours maximal et minimal. The contour of the new gauge shall fall between the maximum and minimum contours
2) Voir la note 2 de l'article 5. See Note 2 of Clause 5.
3) Voir l'article BI. See Clause BI.
4) Quand on contrôle les logements de rotule destinés à utiliser les goupilles normalisées, on peut utiliser le calibre destiné à vérifier les logements de rotule pour les agrafes W, celui-ci étant complété par un calibre plat de façon que la hauteur totale corresponde à la valeur H2 pour la goupille. When gauging sockets for use with standard split-pins, the gauge designed for checking sockets with W-clips may be used, supplemented by a flat gauge such that the total height corresponds to the value of Hz with split-pin.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
IEC 120 84 L(ôLJL(87L 0007909 b I
- 32 - 120 O CE1 1984
B12. Calibre du logement de rotule a NE PASSE PAS )) pour la hauteur de l?entrée
Socket ?NOT GO? gauge for entry height
45 f I 201 177
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
120 O IEC 1984 - 33 -
D&ignation de I'assemblage
Designated size of couping
Calibre - Gauge 1 DI 1 0 4 1 DK 1 HI I Hs 1 Ri
I l I I I I I
10,9 17,05 12,3 11,816 30,5 35,008 Contour max. I Max. contour Contour nominal Nominal contour I l0,8 I 17,00 I 12,O I 11,800 I 30,O I 35,000
Contour min. I Min. contour '1 I 10,7 I 16,95 I 11,7 I 17,784 I 29,5 I 34,992
15,9 30,l 18,3 16,120 40,5 23,010
16 A 15,8 30,O 18,O 16,100 40,O 23,000
15,7 29,9 17,7 16,080 39,5 22,990
Contour max. ax. contour '1 Contour nominal Nominal contour Contour min. Min. contonr I)
I I I I I I l
Contour max. I5,9 30,l 18,3 18,620 40,5 23,010 I Max. contour I) Contoür nominal
1 6 B I Nominal contour I 15,8 I 30,O 1 18,O I 18,600 I 40,O I 23,000
Contour min. I Min. contour ') I 15,7 I 29,9 I 17,7 I 18,580 I 39,s ~ I 22,990
Contour max. I ax. contour ') I 19,s 1 3 6 1 1 23,3 1 22,626 I 50,5 I 27,013
Contour nominal Nominal contour I 19,7 I 36,O I 23,O I 22,600 I 50,O I 27,000
19.6 35,9 22,7 22,574 49,5 26,987
23.7 42,l 28,3 26,030 5 5 3 40,015
23,6 42,O 28,O 26,000 55,O 40,000
23,5 41,9 27,7 25,970 54,5 39,985
Contour min. Min. contour I) Contour max. Max. contour I) Contour nominal
24 Nominal contour Contour min. Min. contour I) Contour max. I M=. contour '1 I 27,6 I 47,l I 32,3 I 28,935 I 60,5 I 55,018
Contour nominal . Nominal contour 28 I I 27,5 I 47,O I 32.0 I 28,900 I 60,O I 55,000
Contour min. I Min. contour I 27,4 1 46,9 I 31,7 I 28,865 I 59,s I 54,982
31,5 52,l 36,3 33,340 70,s 70,020
32 Nominal contour 31,4 52,O 360 33,300 70,O 70,000
31,3 51,9 35,7 33,260 69,5 69,980
Contour max. Max. contour I) Contour nominal
Contour min. Min. contour I)
I ) Le contour du calibre doit être compris entre les contours maximal et minimal. The contour of the gnuge shall fall bclwccn the maximum and minimum contours.
35,008 I 1,8
35,000 I 1,5
34,992 1 l,Z "I 50,010 3,3
60,013
60,000
70,000
69,985
79,982 I 4,2
89,980
e- ,.
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
- 34 - 120 O CE1 1984
Désignation de l’assemblage Designated size
of coupling
11
16
B13. Calibre du logement de rotule G NE PASSE PAS B pour la largeur de l’ouverture Socket “NOT GO” gauge for neck width
Dl
13,800 f 0,011
20,800 f 0,014
45 f 5”)\
24
28
30,000 f 0,020 55,O f 0,5 1,O f 0,3
34,900 f 0,023 60,O f 0,5 1,0 f 0,3
4 30,O f 0,5
32
1,O f 0,3
39,300 f 0,026 70,O f 0,5 1,O f 0,3
40,O f 0,5 I 1,O f 0,3
20 I 25,100 f 0,018 I 50,O f 0,5 1,0 f 0,3 I
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---
Publications de la C E I préparées par le Comité d’Etudes no 36
120 (1984) Dimensions des assemblages à rotule et logement de rotule des éléments de chaînes d‘isolateurs.
137 (1984) Traversées isolées pour tensions alternatives supérieu- res à 1 O00 V.
168 (1979) Essais des supports isolants d’intérieur et d‘extérieur, en matière céramique ou en verre, destinés à des ins- tallations de tension nominale supérieure à 1 O00 V. Modification n’ 1 (1982).
233 (1974) Essais des enveloppes isolantes destinées à des appa- reils électriques.
273 (1979) Dimensions des supports isolants et éléments de sup- ports isolants d’intérieur et d’extérieur destinés à des installations de tension nominale supérieure à 1 O00 v.
305 (1978) Caractéristiques des éléments de chaînes d‘isolateurs du type capot et tige.
372 (1 984) Dispositifs de verrouillage pour les assemblages àrotu- le et logement de rotule des éléments de chaînes d’iso- lateurs. - Dimensions et essais.
383 (1983) Essais des isolateurs en matière céramique ou en verre destinés aux lignes aériennes de tension nominale supérieure à 1 O00 V.
433 (1980) Caractéristiques des éléments de chaînes d’isolateurs du type fût long.
437 (1973) Essai de perturbations radioélectriques des isolateurs pour haute tension.
438 (1973) Essais et dimensions des isolateurs pour hautes ten- sions continues.
471 (1977) Dimensions des assemblages à chape et tenon des élé- ments de chaînes d‘isolateurs. Modification n’ 1 (1980).
506 (1975) Essais sous chocs de manœuvres des isolateurs pour haute tension.
507 (1975) Essais sous pollution adc ie l le des isolateurs pour haute tension destinés aux réseaux à courant alterna- tif.
575 (1977) Essai d‘endurance thermomécanique et essai d’endu- rance mécanique des éléments de chaînes d‘isola- teurs.
591 (1 978) Règles de prélèvements d’échantillons et d’acceptation d’une fourniture quand on applique le calcul statisti- que aux essais mécaniques et électromécaniques des isolateurs en matière céramique ou en verre destinés aux lignes aériennes de tension nominale supérieure à 1 O00 v.
660 (1979) Essais des supports isolants d’intérieur en matière organique destinés à des installations de tension nomi- nale supérieure à 1 O00 V jusqu’à 300 kV non com- pris.
720 (1981) Caractéristiques des isolateurs rigides à socle. 797 (1984) Résistance résiduelle des éléments de chaîne d’isola-
teurs en verre ou en matière céramique pour lignes aériennes après détérioration mécanique du diélectri- que.
I E C publications prepared by Technical Committee No. 36
120 (1984) Dimensions of ball and socket couplings of string insu- lator units.
137 (1984) Bushings for alternating voltages above 1 O00 v.
168 (1979) Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 O00 V. Amendment No. 1 (1982).
233 (1974) Tests on hollow insulators for use in electrical equip- ment.
273 (1979) Dimensions ofindoor and outdoor post insulators and post insulator units for systems with nominal voltages greater than 1 O00 V.
305 (1978) Characteristics of string insulator units for the cap and
372 (1984) Locking devices for ball and socket couplings of string insulator units. - Dimensions and tests.
Pin type.
383 (1983) Tests on insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 O00 v.
433 (1980) Characteristics of string insulator units of the long rod type.
437 (1973) Radio interference test on high-voltage insulators.
438 (1973) Tests and dimensions for high-voltage d.c. insula-
471 (1977) Dimensions of clevis and tongue couplings of tors.
string insulator units. Amendment No. 1 (1980).
506 (1975) Switching impulse tests on high-voltage insulators.
507 (1975) Artiñcial pollution tests on high-voltage insulators to be used on a.c. systems.
575 (1977) Thermal-mechanical performance test and mechani- cal performance test on string insulator units.
591 (1978) Sampling rules and acceptance criteria when applying statistical control methods for mechanical and elec- tromechanical tests on insulators of ceramic material or glass for overhead lines with a nominal voltage greater than 1 000 V.
660 (1979) Tests on indoor post insulators of organic ma- terial for systems with nominal voltages greater than 1 O00 V up to but not including 300 kV.
720 (1981) Characteristics of line post insulators. 797 (1984) Residual strength of string insulator units of glass or
ceramic material for overhead lines after mechanical damage of the dielectric.
Publication 120
Copyright International Electrotechnical Commission Provided by IHS under license with IEC
Not for ResaleNo reproduction or networking permitted without license from IHS
--`,,`,-`-`,,`,,`,`,,`---