ICOM BMW ISIS User Manual

11
BMW ISID configuration manual Firstly install the vmware workstation. Please insert the USB Key before you start the vmware workstation. This is very important, otherwise the software will not able to run correctly!!!! 1. Install VMware Workstation 8, run and select Virtual Network Editor. EOBDTOOL Technology Co,. Ltd. www.eobdtool.com E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

description

 

Transcript of ICOM BMW ISIS User Manual

Page 1: ICOM BMW ISIS User Manual

BMW ISID configuration manual

Firstly install the vmware workstation.

Please insert the USB Key before you start the vmware workstation. This is very important,

otherwise the software will not able to run correctly!!!!

1. Install VMware Workstation 8, run and select Virtual Network Editor.

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 2: ICOM BMW ISIS User Manual

2. Configure network exactlly as on picture. At green ellipse marked place for VMnet0 select

network adapter which will be used for connection with ICOM, OPS or ENET cable.

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 3: ICOM BMW ISIS User Manual

3. Open ISID virtual machine. If you have Win x64 and host RAM more then 4Gb, then you can set

ISID memory size from 1536Mb to 2048Mb. ISSS can process Exx with 2048Mb instead of

4096Mb, but will show you warnings. Don't use other values since this will cause failures.

4. Open VM properties and check Network Adapter set to VMnet2, close and boot.

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 4: ICOM BMW ISIS User Manual

5. When asked, select "I moved it".

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 5: ICOM BMW ISIS User Manual

6. Wait until VM boots and ISTA icon gets active.

7. Connect ICOM using network cable to PC, then connect ICOM to car, wait about minute or two.

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 6: ICOM BMW ISIS User Manual

8.Click right mouse button over connection icon on the right bottom VM window corner and

select "Settings...".

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 7: ICOM BMW ISIS User Manual

9. Change Network connection type to "Bridged" then press "Ok".

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 8: ICOM BMW ISIS User Manual

10. Connection icon will change to inactive state and after some time gets back to active. Wait

1-2 minutes, then start ISTA via one-double left mouse button click over ISTA-D icon in WSM

interface.

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 9: ICOM BMW ISIS User Manual

11. For ISID select "Identification"

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 10: ICOM BMW ISIS User Manual

12. Next for ISID click on "Read out vehicle data" then "Ok"

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag

Page 11: ICOM BMW ISIS User Manual

13. After some time in ISID "Connection manager" list should appear your ICOM. Select it and

press "Set up connection" or "Connect".

Then just enjoy it!!

EOBDTOOL Technology Co,. Ltd.

www.eobdtool.c

om

E-mail:[email protected] MSN:[email protected] Tel:86-755-36870925 Skype: cndiag