icalabmanualpart1

8/10/2019 icalabmanualpart1

1/45

Lab manual

for

IC Applications Lab

III B. Tech I Semester

Prepared by

J. Sunil Kumar

&

B. Ramu

Department of Electronics & Communication Engineering

TurbomachineryInstitute of Technology & Sciences(Approved by AICTE & Affiliated to JNTUH)Indresam(v), Patancheru(M), Medak(Dist). Pin: 502 319


2/45

IC Applications Lab Manual

- 2 -

TurbomachineryInstitute of Technology & Sciences

Certificate

This is to certify that Mr. / Ms. .. RollNo.. of

I/II/III/IV B.Tech I / II Semester of ...branch has completed

the laboratory work satisfactorily in ........Labfor the academic year 20

to 20 as prescribed in the curriculum.Place: ..

Date: ...

Lab In charge Head of the Department Principal

.


3/45


- 3 -

List of Experiments

Cycle 1:

1. Applications of Op-Amp

2. Active Filters

3. Wien Bridge Oscillator

4. Multivibrators using IC 555 ( Astable & Monostable )

5. Schmitt trigger

6. PLL application

Mini Project:

1. Design Function Generator

2. Power supply Design

Cycle 2:

1. Flip Flops

2. Counter (Synchronous & Asynchronous)

3. Comparator

4. Mux

5. RAM

6. Stack & Queue implementation using RAM


4/45


- 4 -

Lab Exam Question Paper

1. a) Design a three input adder circuit to have a voltage gain of 3. Calculate the resistor values,

currents and output voltage when all the input voltages are 1V.

b) A substractor is to be designed to amplify the difference between two voltages by a factor

of 10. The inputs each approximately equal 1V. Determine suitable resistor values for a

circuit using a 741 Op-Amp.

c) Using 741 Op-Amp Design Comparator Circuit

d) Using a 741 Op-Amp, Design a low pass filter to have cutoff frequency of 1kHz.

e) Using a 741 Op-Amp, Design a high pass filter circuit to have cutoff frequency of 5kHz.

2. a) Design a Butterworth second order low pass filter, to have cutoff frequency of 1kHz.

Calculate the actual cutoff frequency.

b) Design a Butterworth second order high pass filter, to have cutoff frequency of 12 kHz.

Using the selected component values, calculate the actual cutoff frequency for the circuit.

3. Design a wein bridge oscillator to produce 100kHz, 9V output.

4. Using 555 timer Design Astable & Monostable Multivibrators

5. Using a 741 op-amp, calculate resistor values for the Schmitt trigger circuit to give

triggering points of 5V.

6. Using 566 IC design a VCO Circuit

7. The regulator circuit id to have an output of 10V. Calculate resistor values for R1 and R2,

select a suitable input voltage and determine the maximum load current that may be

supplied if PD(max)= 1000mW


5/45


- 5 -

Exp. No. 1 Date:

APPLICATION OF OP-AMP(Adder, Substractor, Comparator, Integrator, Differentiator)

Aim:

a) Design a three input adder circuit to have a voltage gain of 3. Calculate the resistor

values, currents and output voltage when all the input voltages are 1V.

b) A substractor is to be designed to amplify the difference between two voltages by a

factor of 10. The inputs each approximately equal 1V. Determine suitable resistor

values for a circuit using a 741 op-amp.

c) Using 741 Op-Amp Design Comparator Circuit

d) Using 741 op-amp, Design a low pass filter to have cutoff frequency of 1kHz.

e) Using 741 op-amp, Design a high pass filter circuit to have cutoff frequency of 5kHz.

Apparatus Required:

S. No. Name of the Component Specification Quantity

1 Op-amp A741 1

33k 3

2 Resistors 100k 1

3 Signal Generator 0-10MHz 1

4 IC Regulated Power Supply 15V 1

5 Connecting Wires Single Strand As Required

6 Bread Board 1

Theory:

Adder:

Op-Amp may be used to design a circuit whose output is the sum of several input

signals such as circuit is called a summing amplifier or summer. We can obtain either

inverting or non inverting summer.

The circuit diagrams shows a two input inverting summing amplifier. It has two

input voltages V1and V2, two input resistors R1, R2 and a feedback resistor Rf.

Assuming that op-amp is in ideal conditions and input bias current is assumed to be

zero, there is no voltage drop across the resistor Rcomp and hence the non inverting input

terminal is at ground potential. By taking nodal equations.


6/45


- 6 -

Adder Circuit Diagram:

-

++

U1 UA741/301R1 33kOhm

R2 33kOhm

R4 100kOhm

Vee 15V

Vcc 15V

+

Vi

VF2

R3 33kOhm

Adder Waveforms:

T

Input signal

0.00 50.00m 100.00m 150.00m 200.00m

Axis

label

-1.00

-500.00m

0.00

500.00m

1.00

Input signal


7/45


- 7 -

V1/R1 +V2/R2 +V0/Rf = 0

V0 = - [(Rf/R1) V1 + (Rf/R2) V2]

And here R1 = R2 = Rf = 1K

V0 = - (V1 +V2)

Thus output is inverted and sum of input.

Substractor:

A basic differential amplifier can be used as a sub tractor. It has two input signals V1 and

V2 and two input resistances R1 and R2 and a feedback resistor Rf. The input signals scaled to

the desired values by selecting appropriate values for the external resistors.

From the figure, the output voltage of the differential amplifier with a gain of 1 is

V0 = -R/Rf(V2-V1) V0 = V1-V2.

Also R1 =R2 = Rf =1K.

Thus, the output voltage V0 is equal to the voltage V1 applied to the non inverting

terminal minus voltage V2 applied to inverting terminal.

Hence the circuit is sub tractor.

Comparator:

A comparator is a circuit which compares a signal voltage applied at one input of an

op-amp with a known reference voltage at the other input . It is basically an open loop op-

amp with output Vsat as in the ideal transfer characteristics.

It is clear that the change in the output state takes place with an increment in input Vi

of only 2mv. This is the uncertainty region where output cannot be directly defined There are

basically 2 types of comparators.

1. Non inverting comparator and.

2. Inverting comparator.

The applications of comparator are zero crossing detector , window detector, time marker

generator and phase meter.


8/45


- 8 -

T

Output Signal

0.00 50.00m 100.00m 150.00m 200.00m

Axis

label

-10.00

-5.00

0.00

5.00

10.00

Output Signal

Substractor Circuit Diagram:

-

++3

2

6

7

4

OP1

R1

R2

R3

R4

VF1

V1

V2

+

VG1

+

VG2


9/45


- 9 -

Low Pass Filter:

The first order low pass butter worth filter uses an Rc network for filtering. The

op-amp is used in the non inverting configuration, hence it does not load down the RC

network. Resistor R1 and R2 determine the gain of the filter.

V0/Vin = Af/(1+ jf/fh)

Af = 1 + Rf/R1 = pass band gain of filter .

F = frequency of the input signal.

Fh = 1/2RC =High cutt off frequency of filter .

V0/Vin = Gain of the filter as afunction of frequency

The gain magnitude and phase angle equations of the LPF the can be obtained by

converting V0/Vin into its equivalent polar form as follows

|V0/Vin| = Af/(1 +(f/fl)2)

= - tan-(f / fh)Where is the phase angle in degrees . The operation of the LPF can be verified

from the gain magnitude equation.

1. At very low frequencies i.e ffh , |V0/Vin|


10/45


- 10 -

T Input Signal at terminal 3

0.00 50.00m 100.00m 150.00m 200.00m

Axislabe

l

-2.00

-1.00

0.00

1.00

2.00Input Signal at terminal 3

TInput Signal at terminal 2

0.00 50.00m 100.00m 150.00m 200.00m

Axislabel

-1.00

-500.00m

0.00

500.00m

1.00Input Signal at terminal 2

T

Substrator Output Signal

0.00 50.00m 100.00m 150.00m 200.00m

Ax

islabe

l

-1.00

-500.00m

0.00

500.00m

1.00

Substrator Output Signal


11/45


- 11 -

F =frequency of input signal.

Fl =1/2RC = lower cutt off frequency

Hence, the magnitude of the voltage gain is

|V0/Vin| =Af(f/fl)/1+(f/f1)2.

Since, HPFs are formed from LPFs simply by interchanging Rs and Cs .The

design and frequency scaling procedures of the LPFs are also applicable to HPFs.

Procedure:

Adder:

1. connections are made as per the circuit diagram.

2. Apply input voltage 1) V1= 5v,V2=2v

2) V1= 5v,V2=5v

3) V1= 5v,V2=7v.

3. Using Millimeter measure the dc output voltage at the output terminal.

4. For different values of V1 and V2 measure the output voltage.

Substractor:

1. Connections are made as per the circuit diagram.

2. Apply input voltage 1) V1= 5v,V2=2v

2) V1= 5v,V2=5v

3) V1= 5v,V2=7v.

3. Using multi meter measure the dc output voltage at the output terminal.4. For different

values of V1 and V2 measure the output voltage.

Comparator:


2. Select the sine wave of 10V peak to peak , 1K Hz frequency.

3. Apply the reference voltage 2V and trace the input and output wave forms.

4. Super-impose input and output waveforms and measure sine wave amplitude

with reference to Vref.

5. Repeat steps 3 and 4 with reference voltages as 2V, 4V, -2V, -4V and observe the

waveforms.

6. Replace sine wave input with 5V dc voltage and Vref= 0V.


12/45


- 12 -

Comparator Circuit Diagram:

OBSERVATIONS:

Adder:

V1(volts) V2(volts) V3(volts) Theoretical

V0 = -(V1+V2+V3)

Practical

V0 = -(V1+V2+V3)

Subtractor:

V1(volts) V2(volts) Theoretical

V0 = (V1-V2)

Practical

V0 = (V1-V2)

Comparator:

Voltage input Vref Observed wave amplitude


13/45


- 13 -

7. Observe dc voltage at output using CRO.

8. Slowly increase Vref voltage and observe the change in saturation voltage.

Differentiator:


2. Apply sine wave of amplitude 4Vp-p to the non inverting input terminal.

3. Values the input signal frequency.

4. Note down the corresponding output voltage.

5. Calculate gain in db.

6. Tabulate the values.

7. Plot a graph between frequency and gain.

8. Identify stop band and pass band from the graph.

Integrator:


2. Apply sine wave of amplitude 4Vp-p to the non inverting input terminal.

3. Values the input signal frequency.

4. Note down the corresponding output voltage.

5. Calculate gain in db.

6. Tabulate the values.

7. Plot a graph between frequency and gain.

8. Identify stop band and pass band from the graph.

Precautions:

1. Make null adjustment before applying the input signal.

2. Maintain proper Vcc levels.


14/45


- 14 -

Differentiator Circuit Diagram

-

++

3

2

6

7

4

OP1 uA741

+ VG1

R2 33kV15

V25

VF1

VF2 C1 1n

R133k

Integrator

-

++

3

2

6

7

4

OP1 uA741

+ VG1

R1 120k

R2 120kV15

V25

VF1

C11

.32n

VF2

Differentiator Response

T

Ga

in(dB)

-60.00

-50.00

-40.00

-30.00

-20.00

-10.00

0.00

10.00

Frequency (Hz)

10 100 1k 10k 100k 1M

Phase

[deg

]

-100.00

-50.00

0.00

50.00

100.00


15/45


- 15 -

Viva Question:

1. What is an op-amp?

2. Give the characteristics of an ideal op-amp:

3. How a non-inverting amplifier can be courted into voltage follower?

4. What is the necessity of negative feedback?

5. What are 4 building blocks of an op-amp?

6. What is the purpose of shunting Cfacross Rfand connecting R1in series with the input signal?

7. What are the applications of Differentiator?

8. What do you mean by unity gain bandwidth?

9. What did you observe at the output when the signal frequency is increased above fa?

10. How would you eliminate the high frequency noise in integrator?

11. What are the main applications of the Integrator?

12. Is it possible to design an analog computer using integrator and differentiator?

13. What happens to the output of integrator when input signal frequency goes below fa?

Result:Thus Adder, Substractor, Comparator, Differentiator, Integrator, using op-amp was

designed and tested.


16/45


- 16 -

Integrator

Frequency(Hz) V0(V) Gain in db=20log(V0/Vi)

Differentiator

Frequency (Hz) V0(V) Gain in db= 20log(V0/Vi)


17/45


- 17 -


18/45


- 18 -

Integrator Response

T

Ga

in(

dB)

-70.00

-60.00

-50.00

-40.00

-30.00

-20.00

-10.00

0.00

10.00

Frequency (Hz)

10 100 1k 10k 100k 1M

Phase

[deg

]

-200.00

-150.00

-100.00

-50.00

0.00


19/45


- 19 -

Exp. No. 2 Date:

ACTIVE FILTERSAim:

a) Design a Butterworth second order low pass filter, to have cutoff frequency of 1kHz.

Calculate the actual cutoff frequency.

b) Design a Butterworth second order high pass filter, to have cutoff frequency of 12kHz. Using

the selected component values, calculate the actual cutoff frequency for the circuit.

Apparatus Required:

S. No. Name of the Component Specification Quantity

1 OP AMP A741 1

22k 22 Resistors 39k 1

0.01F 1

3 Capacitors 0.001uF 24 Fixed Power Supply 15 V 1

5 Function Generator 2MHz 1

6 CRO 20MHz 1

7 General Purpose Trainer Kit 1

8 Connecting wires Single Strand 1

9 CRO Probes Crocodile Clips 2

Theory:

A filter is a device that passes electric signals at certain frequencies. Butterworth is one

of the most commonly used filter optimizations. It has the following characteristics:

It provides monotonic response, the maximally flat pass band response. For this reason, it is

sometimes called aflat-flat filter.

Butterworth filters are used as anti-aliasing filters in data converter applications where

precise signal levels are required across the entire pass band.

The frequency response below shows the transition band ( fc to f1) where the response shifts

from the pass band to the stop band. The pass band ends when A1 is -3db down from the low

frequency response A0. The stop band enters when the response drops to some

predetermined value A2.

LPF

A LPF allows only low frequency signals up to a certain break-point fH to pass through,

while suppressing high frequency components. The range of frequency from 0 to higher cut off

frequency fH is called pass band and the range of frequencies beyond fH is called stop band.

The following steps are used for the design of active LPF.


20/45


- 20 -

Circuit Diagram:

Butterworth Low Pass Filter

-

++

3

2

6

7

4

OP1 uA741

R1 22k R2 22k

C15n

C2 10n

R3 39k

+ VG1

V15

V25

VF1

VF2

Butterworth High Pass Filter

-

++

3

2

6

7

4

OP1 uA741

R1 10k

C1 1n

C2 1n

R3 18k

+ VG1

V15

V25

VF1

VF2

R218k

Butterworth Low Pass Filter Response

T

Ga

in

(dB)

-200.00

-100.00

0.00

100.00

Frequency (Hz)

10 100 1k 10k 100k 1M

Phase

[deg

]

-100.00

0.00

100.00

200.00


21/45


- 21 -

1. The value of high cut off frequency fHis chosen.

2. The value of capacitor C is selected such that its value is 1m F.

3. By knowing the values of fHand C, the value of R can be calculated using

4. Finally the values of R1and Rfare selected depending on the designed pass band gain by

using

Second order HPF:

The high pass filter is the complement of the low pass filter. Thus the high pass filter can

be obtained by interchanging R and C in the circuit of low pass configuration. A high pass filter

allows only frequencies above a certain bread point to pass through and at terminates the lowfrequency components. The range of frequencies beyond its lower cut off frequency fLis called

stop band.

Procedure:

LPF:-

1. Connections are given as per the circuit diagram.

2. Input signal is connected to the circuit from the signal generator.

3. The input and output signals of the filter channels 1 and 2 of the CRO are connected.

4. Suitable voltage sensitivity and time-base on CRO is selected.

5. The correct polarity is checked.

6. The above steps are repeated for second order filter.

HPF

1. Connections are given as per the circuit diagram.

2. Input signal is connected to the circuit from the signal generator.

3. The input and output signals of the filter channels 1 and 2 of the CRO are connected.

4. Suitable voltage sensitivity and time-base on CRO is selected.5. The correct polarity is checked.

6. The above steps are repeated for second order filter.

Result:-

Thus the second order Low pass filter and High pass filter were designed using Op-amp and its

cut off frequency was determined.


22/45


- 22 -

LPF

HPF


23/45


- 23 -

Tabular Column : (LPF)

S. No. Frequency Output Voltage (Vo) Gain (Vo/ Vin)

Tabular Column : (HPF)

S. No. Frequency Output Voltage (Vo) Gain (Vo/ Vin)


24/45


- 24 -

Butterworth High Pass Filter Response:

T

Ga

in

(dB)

-70.00

-60.00

-50.00

-40.00

-30.00

-20.00

-10.00

0.00

10.00

Frequency (Hz)

10 100 1k 10k 100k 1M

Phase

[deg

]

-400.00

-300.00

-200.00

-100.00

0.00


25/45


- 25 -

Exp. No. 3 Date:

WEIN BRIDGE OSCILLATORAim:

Design a Wein-Bridge Oscillator to produce 100kHz, 9V output.

Apparatus Required:

S. No. Component Specification Quantity

1 IC LM 565 1

2 Resistors 1.5k 1

10k 1

4.7k 2

2k 1

3 Capacitor 0.047F, 0.1F 1

4 Variable Resistor 10k 1

5 Fixed Power Supply 15V 1


7 CRO 0-30MHz 1


9 Bread Board 1

Theory:

An oscillator consists of an amplifier and a feedback network.

1) 'Active device' i.e. Op Amp is used as an amplifier.

2) Passive components such as R-C or L-C combinations are used as feed back net work.

To start the oscillation with the constant amplitude, positive feedback is not the onlysufficient condition. Oscillator circuit must satisfy the following two conditions known as

Barkhausen conditions:

a. The first condition is that the magnitude of the loop gain (A) = 1

A = Amplifier gain and = Feedback gain.

b. The second condition is that the phase shift around the loop must be 360 or 0.

The feedback signal does not produce any phase shift. This is thebasic principle of a Wien

bridge oscillator. The given circuit shows the RC combination used in Wien bridge oscillator.

This circuit is also known as lead-lag circuit. Here, resistor R1 and capacitor C1 are connected in

the series while resistor R2and capacitor C2 are connected in parallel. At high frequencies, the

reactance of capacitor C1 and C2 approaches zero. This causes C1 and C2 appears short. Here,

capacitor C2 shorts the resistor R2. Hence, the output voltage Vo will be zero since output is

taken across R2 and C2 combination. So, at high frequencies, circuit acts as a 'lag circuit'.

C1combination. Here, the circuit acts like a 'lead circuit'. But at one particular frequency

between the two extremes, the output voltage reaches to the maximum value. At this frequency


26/45


- 26 -

Circuit Diagram:

-

++

3

2

6

7

4uA741

R

11

.5k

C1 1n

R21

.5k

C21n

R33

.3k

R4 1.5k

VF1

V110

V210

Design:

Gain required for sustained oscillation is Av= 1/b = 3

(PASS BAND GAIN) (i.e.) 1+Rf/R1= 3

Rf= 2R1

Frequency of Oscillation fo = 1/2p R C

Given fo= 1 KHz

Let C = 0.05 F

R = 1/2 foC

R = 3.2 KW

Let R1= 10 K\ Rf= 2 * 10 K

Model Output Signal

T

0.00 10.00u 20.00u 30.00u 40.00u 50.00u

Ax

islabe

l

-2.00

-1.00

0.00

1.00

2.00


27/45


- 27 -

only, resistance value becomes equal to capacitive reactance and gives maximum output. Hence,

this particular frequency is known as resonant frequency or oscillating frequency.

The maximum output would be produced if

R = Xc.= 1/(2fC)

IfR1=R2= R and C1= C2= CThen the resonant frequency f = 1/(2RC)

Due to limitations of the op-amp, frequencies above 1MHz are not achievable.

The basic version of Wein bridge has four arms. The two arms are purely resistive and

other two arms are frequency sensitive arms. These two arms are nothing but the lead-lag circuit.

The series combination of R1 and C1 is connected between terminal a and d. The parallel

combination of R2 and C2 is connected between terminal d and c . So the two circuits (Fig.1 and

Fig.2) are same except in shape. Here, bridge does not provide phase shift at oscillating

frequency as one arm consists of lead circuit and other arm consists of lag circuit. There is noneed to introduce phase shift by the operational amplifier. Therefore, non inverting amplifier is

used.

Procedure:

1. Connect the components as shown in the circuit

2. Switch on the power supply and CRO.

3. Note down the output voltage at CRO.

4. Plot the output waveform on the graph.

5. Redesign the circuit to generate the sine wave of frequency 2KHz.

6. Compare the output with the theoretical value of oscillation.

Observation:

Peak to peak amplitude of the output = __________Volts.

Frequency of oscillation = __________Hz.

Questions:

1. State the two conditions for oscillations.

2. Classify the Oscillators?

3. Define an oscillator?

4. What is the frequency range generated by Wein Bridge Oscillator?

5. What is frequency stability?

Result:

Thus wein bridge oscillator was designed using op-amp and tested.


28/45


- 28 -


29/45


30/45


- 30 -

Circuit Diagram:

Astable Multivibrator:

Monostable Multivibrator

Monostable Multivibrator Model Graph:


31/45


- 31 -

duty cycle ratio is defined as the ratio as the time during which the output is high to the total

time period.

Duty cycle = tdT X100

RB+ RA+ 2RB X 100 ( 5 )

To obtain 50% duty cycle a diode should be connected across RB and RA must be a

combination of a fixed resistor and a potentiometer. So that the potentiometer can be adjusted

for the exact square waves

Monostable Multivibrators has one stable state and other is a quasi stable state. The

circuit is useful for generating single output pulse at adjustable time duration in response to a

triggering signal. The width of the output pulse depends only on external components, resistor

and a capacitor. The stable state is the output low and quasi stable state is the output high. In the

stable state transistor Q1 is on and capacitor C is shorted out to ground. However upon

application of a negative trigger pulse to pin2, Q1 is turned off which releases the short circuit

across the external capacitor C and drives the output high. The capacitor C now starts charging

up towards Vcc through RA. However when the voltage across C equal 2/3 Vcc the upper

comparator output switches form low to high which in turn drives the output to its low state via

the output of the flip-flop. At the same time the output of the flip flop turns Q1 on and hence C

rapidly discharges through the transistor. The output remains low until a trigger is again applied.

Then the cycle repeats. The pulse width of the trigger input must be smaller than the expected

pulse width of the output. The trigger pulse must be of negative going signal with amplitude

larger than 1/3 Vcc. The width of the output pulse is given by,

T = 1.1 RAC

Astable Multivibrator Design:

fo= 1/T = 1.45 / (RA+2RB)C

Choosing C = 1 m F; RA= 560

D = RB/ RA+2RB= 0.5 [50%]

RB= ______

Monostable Multivibrator Design:

Given a pulse width of duration of 100 m s

Let C = 0.01 mfd; F = _________KHz

Here, T= 1.1 RAC

So, RA=


32/45


- 32 -

Astable Multivibrator Model Graph:

Astable Multivibrator Observations:

Theoretical Time Period Practical Time Period

Monostable Multivibrator Observations:

Theoretical Time Period Practical Time Period


33/45


- 33 -

Precautions:

1. Make the null adjustment before applying the input signal.

2. Maintain proper vcc levels.

Result:

Operation of Monostable and Astable multivibrators using 555 IC trainers is studied

and wave forms are noted.

Viva Questions:

1. What is another name for mono stable multi?

2. What is the purpose of pin reset?

3. Define duty cycle?

4. What are the various applications of one shot?

5. How many external triggers are necessary in one shot?

6. Define astable multi?

7. Explain the pulse width of the astable multi?

8. What is the other name for astable multi?

9. Write one application of free running oscillator?

10. How many external triggers are necessary for astable?


34/45


- 34 -


35/45


- 35 -

Exp. No. 5 Date:

SCHMITT TRIGGER CIRCUITS USING IC 741

Aim: To design and test Schmitt trigger using Op-Amp

Apparatus Required:


1 Op-Amp A741 1

2 Resistors 120 1

47k 1

10k 1

3 Fixed Power Supply 15 V 1

4 Function Generator 0 2MHz 1

5 CRO 0 30 MHz 1

6 CRO Probes 2

7 Bread Board 1

8 Connecting Wires As Required

Theory:

The Schmitt Trigger is a type of comparator with two different threshold voltage levels.

Whenever the input voltage goes over the High Threshold Level, the output of the comparator

is switched HIGH (if is a standard ST) or LOW (if is an inverting ST). The output will remain in

this state, as long as the input voltage is above the second threshold level, the Low Threshold

Level. When the input voltage goes below this level, the output of the Schmitt Trigger will

switch. The HIGH and LOW output voltages are actually the POSITIVE and NEGATIVE

power supply voltages of the comparator. The comparator needs to have positive and negative

power supply (like + and -) to operate as a Schmitt Trigger normally. The following drawing

shows how a Schmitt Trigger would react to an AC voltage input:

When the non-inverting input (+) is higher than the inverting input (-), the comparator

output switches to the POSITIVEvoltage supply. On the contrary, the non-inverting input (+) is

lower than the inverting input (-), the output switches to the NEGATIVEvoltage supply. The

inverting input (-) is grounded, so someone would expect that the turn-on and off point would be

the ground (0). The function of the ST comes from the feedback resistor RFB. When for example

the output of the comparator is to the POSITIVEvoltage supply, then the non-inverting input

has through the RFB this voltage! The same happens when the output is to the NEGATIVE

power supply.

The voltage needed to switch the output of the comparator must be above or below zero

(ground), according to the POSITIVE and NEGATIVE power supply and according to the

resistors RIand RFB. More specific, the formula to calculate the threshold voltage is:


36/45


37/45


- 37 -

VTHRESHOLD= VSUPPLYx RI/(RFB+ RI)

So, if the output is to the POSITIVE voltage, the required negative voltage that must be

applied to Vin is:

VINPUT= VTHRESHOLD

Procedure:

1. Connect the circuit as shown in the circuit

2. Set the input voltage as 5V (p-p) at 1KHz. (Input should be always less than Vcc)

3. Note down the output voltage at CRO

4. To observe the phase difference between the input and the output, set the CRO in dual

Mode and switch the trigger source in CRO to CHI.

5. Plot the input and output waveforms on the graph.

Observation:

Peak to peak amplitude of the output = Volts.

Frequency = Hz.

Upper threshold voltage = Volts.

Lower threshold voltage = Volts.

Viva Questions:

1. What is Hysteresis? What parameter determines Hysteresis?

2. How would you recognize that positive feedback is being used in the Op-amp circuit?

3. What do you mean by upper and lower threshold voltage in Schmitt Trigger?

4. What is the difference between a basic comparator and the Schmitt trigger?

5. What is a sample and hold circuit? Why is it needed?

6. What is a voltage limiting, and why is it needed?

7. What is the name of the circuit that is used to detect the peak value of the Non-

sinusoidal input waveforms?

8. How will you produce, definite Hysteris in a Schmitt trigger using op-amp?

Result: Thus Schmitt Trigger using op-amp was designed & tested.


38/45


- 38 -

Exp. No. 6 Date:

IC 565 PLL APPLICATIONS VCO

Aim: Design a Phase Locked Loop Application (Voltage Controlled Oscillator) using IC

LM565.Apparatus Required:


1 IC LM 565 1

2 Resistors 1.5k 1

10k 1

4.7k 2

2k 1

3 Capacitor 0.047F, 0.1F 1

4 Variable Resistor 10k 1

5 Fixed Power Supply 15V 1


7 CRO 0-30MHz 1


9 Bread Board 1

Theory:

This oscillator uses a special IC chip, the LM565 that is designed to function as a phase

locked loop (PLL). The chip contains a VCO (which we will utilize in this experiment) and a

phase detector. A combination of an input control voltage on pin 7 and the RC time constant

formed by the components on pins 8 and 9 set the VCO output frequency. The VCO within the

LM565 is not designed like a conventional oscillator. It is really a current controlled oscillator.

Remember that as the charging current in a capacitor is increased, the rate of capacitor charging

(as evidenced in its voltage rise) also increases. The same is true for capacitor discharging as

well. The LM565 simply translates the control voltage on pin 7 into a charging and discharging

current for the timing capacitor, C1. So what is the function of the resistors on pin 8? The

resistors on pin 8 also help set the charge and discharge current for the timing capacitor C1. In

other words, the output frequency of the LM565 VCO depends on three factors:

1) The control voltage on pin 7;

2) The total resistance on pin 8 (R3 and R4);

3) The capacitance on pin 9 (C1).

When a capacitor is charged by a constant current, its voltage rises linearly (straight-

line). Thus, one of the output waveforms of the LM565 is a triangle wave. The other output is a

square wave -- the result of the triangle wave going through a Schmitt trigger.


39/45


- 39 -

Circuit Diagram:


40/45


- 40 -

Two different LM565 VCO circuits will be examined in this experiment, and they are

shown in Figures 1 and 2. In Figure 1, the control voltage of the VCO is held constant by

resistors R1 and R2, and the RC time-constant is varied by R3. (Note that the total resistanceRt

in Figure 1 is the series combination of R3 and R4). In Figure 2, the timing resistanceRt is equal

to R2, and is constant. A potentiometer has been substituted in R1's place, allowing the control

voltage to be varied over a range of approximately 7.5 V to 15 V. Note that the control voltage

should be adjusted to be in the range 11.25 V to 15 V in part two of this experiment.

Procedure:

Procedure:


2. Measure the output voltage and frequency of both triangular and squares.

3. Vary the values of R1 and C1 and measure the frequency of the waveforms.

4. Compare the measured values with the theoretical values.

Precautions:

1. Connect the wires properly.

2. Maintain proper Vcclevels.

Result:

The NE/SE 565 is operated as Voltage Controlled Oscillator also the output

frequency for various values of R1 and C1 are observed.

Viva Questions:

1. What are the applications of VCO?

2. Draw the pin diagram of NE/SE 565.

3. What is the need of connecting 0.0047F capacitor between pin 5 and pin 6?


41/45


- 41 -

Observations:

Output Voltage (V)

S. No. R1 C1 Square wave Triangular wave

Theoretical

frequency (KHz)

Practical

frequency

Model Graph:


42/45


- 42 -

Exp. No. 7 Date:

VOLTAGE REGULATOR IC LM723

Aim: To design a high current, low voltage and high voltage linear variable dc regulated power

supply and test its line and load regulation.

Apparatus Required:S. No. Component Specification Quantity

1 Voltage Regulator LM723 1

2 Resistor 3.3k 1

4.7k 1

5.6k(POT) 2

3 Capacitor 100F 1

4 DRB 1

5 Regulated Power Supply 0 15 V 1

6 Multimeter 2

7 Bread Board 1

8 Connecting Wires As Required

Theory:

A Voltage Regulator is a circuit that supplies a constant voltage regardless of changes in

load current and input voltage variations. Using IC 723, we can design both low voltage and

high voltage regulators with adjustable voltage. For a low voltage both regulator, it is Vo>Vref,

where as for high voltage regulator can be designed using Op-Amps, it is quiker and easier to

use IC voltage regulators. IC 723 is a general purpose regulator and is a 14-pin IC with internal

short circuit current limiting, thermal shutdown, current / voltage boosting etc. Furthermore it isan adjustable voltage regulator which can be varied over both positive and negative voltage

ranges. By simply varying the connection made extremely, we can operate the IC in the required

mode of operation. Typical performances parameters are line and load regulations which

determine the precise characteristics of a regulator.

Procedure:

a) Line regulation

1. Connect the circuit as shown in fig.2. Obtain R1 and R2 forVo= 3

3. By varying Vinrom 2 to 10 V, measure the output Voltage Vo

4. Draw the graph between Vin and Vo

5. Repeat the steps for Vo= 5V


43/45


- 43 -

Circuit Diagram:

Model Graphs:


44/45


- 44 -

b) Load RegulationFor Vo= 3V

1. Set Visuch that Vo = 3V

2. By varying RL, measure IL and Vo

3. Plot the graph between IL and Vo

4. Repeat the Steps 1 to 3 for Vo = 5V

Precautions:

1. Check the connection before giving the power supply

2. Readings should be taken carefully

Result: Thus the line and load regulation of a high current, low voltage and high voltage linear

variable dc regulated power supply was designed and tested.

Viva Questions:

i) Why minimum protect resistance in load is required? What will happen if it is not there?

ii) Did you short circuit the output and check whether the short circuit protection is working?

iii)What will you do if you are asked to design both high and low voltage regulators in one

circuit?

iv)Give 10 example applications of the above circuits?


45/45


Observations:

Line Regulation:

Load Resistance RL1 = Load Resistance RL2 =

S. No.Input Voltage

(Vin)

Output Voltage

(Vo)

Input Voltage

(Vin)

output Voltage

(Vo)

Load Regulations:Input Voltage Vin = Input Voltage Vin =

S. No.Output Current

(IL)

Output Voltage

(Vo)

Output Current

(IL)

output Voltage

(Vo)

Calculation of % Voltage Regulation :

% Voltage Regulation = ( Vdc ( NL ) - Vdc ( FL ) ) / Vdc ( FL )

Vdc ( NL ) = D.C. output voltage on no load

Vdc ( FL ) = D.C. output voltage on full load

icalabmanualpart1

Documents

Transcript of icalabmanualpart1