Owner’sM a n u a l

Spin ScrubTM with Powered Hand ToolI I

The Easy to.UseDeep Cleanerwith automatic tool conversion

Review this manual before operating deep cleaner

SteamVacTM Deep Cleaner cleans carpet fibers byapplying hot tap water and cleaning solution.:www.hoover.com

Fill in and RetainThis HOOVER deep cleaner isdesigned for deep cleaning carpet,rugs, carpeted stairs-and upholstery.The model and serial numbers arelocated on the data label on the backof the handle.

For your personal records, pleaseenter the COMPLETE model and serialnumbers in the spaces provided andretain this information.

Your deep cleaner is model

and has serial number

It is suggested that you attach yoursales receipt to this owner s manual.

Verification of date of purchase maybe required for warranty service ofyour Hoover product.

IndexImportant safeguards . . . . . . . . . .Unpacking deep cleaner. . . . . . . . . 3Assembling deep cleaner . . . . . .4-EDeep cleaner description . . . . . . . .6General operation . . . . . . . . . . . .6-9

Filling the clean solution tank. 7-6Emptying the recovery tank . . 8-9Agitator speed selector . . . . . . .7Brush Indicator . . . . . . . . . . . . . .7

How to useBefore you begin . . . . . . . . . . . . 9After cleaning . . . . . . . . . . . . 9-10Cleaning carpet . . . . . . . . . . . . 10Picking up spills . . . . . . . . . . . . 10Cleaning bare floors . . . . . . IO-IIUsing the tools . . . . . . . . . . . . .I1

Cleaning carpeted stairs. . . . . 12Cleaning upholstery . . . . . . . 12

MaintenanceIfyouhaveaproblem.. . . . . . .I4Lubrication . . . . . . . . . . . . . . . .I4Service . . . . . . . . . . . . . . . . . . .I4Storage . . . . . . . . . . . . . . . . . . .I4Warranty . . . . . . . . . . . . . . . . . . .I5

Imnortant Safeauards!When using an electrical appliance; always follow basic

precaution, including the following:

READ ALL INSTRUCTIONS BEFORE USING APPLIANCE.To reduce the risk of fire, electricWARNING:. shock,or in ju ry :

l Use indoors only.l Use only.on surfaces moistened by the cleaning process or small spills. Do

not immerse product.l Connect to a properly grounded outlet only. See “Grounding fnstructions”.l Do not clean over floor electrical outlets.l Do not use without tanks in place.l Use extra care when cleaning on stairs. Do not place deep,cleaner on stairs.l Use deep cleaner only for its intended use as described in the instructions.l Use only attachments recommended byThe Hoover Company; others may

cause hazards.l The use of an&tension cord Is not recommended. If an extension cord is

absolutely necessary, use at least a 16 gauge 3-wire cord which has a 3-pronggrounding type plug and a 3-pole receptacle that accepts the machine plug.

l Unplug deep cleaner when not in use;Turn off all controls before unplugging.l Unplug before connecting the powered hand tool.l Always disconnect cord from electrical outlet before servicing the deep cleaner.l Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.l Never handle plug or appliance with wet hands.l Do not pull or carry by cord, use cord as a handle, close door on cord or pull

cord around sharp edges, or corners. Do not run appliance over cord. Keepcord away from heated surfaces.

l Do not use with damaged cord or plug. If appliance Is not working as it should,has been dropped, damaged, left outdoors, or dropped Into water, take it to aHoover Factory Service Center or Authorized Hoover Warranty Service Dealer.

l Close supervision isnecessary when any appliance is used by or nearchildren. Do not allow deep cleaner to be used as a toy or to run unattended atany time.

l Do not point tools toward people or pets.l Use only commercially available floor cleaners Intended for machlne

application. Do not use any type of wax with deep cleaner.l To assist In reducing drying time, be certain the area Is well ventilated when

using detergents and other cleaners with this machine.l Keep detergents and other cleaners out of children’s reach.l Do not use to pick up flammable or combustible liquids such as gasoline or

use In areas where they may be present.l Do not pick up chlorine bleach, drain cleaner, gasoline or any other toxic

material with this appliance.l Do not pick up anything that is burning or smoking, such as cigarettes,

matches, or hot ashes.l Avoid picking up hard, sharp objects with the deep cleaner. They may damage

the machine..l Keep hair, loose clothing, fingers, feet and all parts of body away from

openlngs and moving parts.l Do not put any object Into openings. Do not use with any opening blocked;

keep free of dust, lint, hair, and anything that may reduce air flow.l To help prevent matting and resoiling, avoid contact with carpets until they are

dry. Keep children and pets away from carpets until they are completely dry.l Store in a dry place. Do not expose machine to freezing temperatures.

Save these instructions!@ @@

0 1993,1996,1997,2001 The Hoover Companywww.hoover.com

2

GroundingInstructi6ns

This appliance must be grounded. If itshould .malfunction or breakdown,grounding provides a path of least resis-tance for electrical current to reduce therisk of electric shock.+This .ap@iance isequipped with a cord having an equip-ment-grounding conductor (C) and

-’grounding ,plug (A). The plug must beplugged>into an appropriate outlet(B)that is properly installed and grounded inaccordance with all locai codes andordinances.

_’

DANGER-Improper connection of the equipment- _grounding conductor can result in therisk of electric shock. Check with a qual-ified-electrician or service person if youare in doubt as to whether the outlet isproperly grounded. Do not modify theplug provided with the appliance.1 if itwill not fit the outlet, have a proper outletinstalled by a qualified electrician. Thisappliance is for use on a nominal 120volt circuit and has a grounding plugthat looks like the plug illustrated insketch (A).

A temporary adapter (D) may be used toconnect this plug to a 2-pole receptacle(E) if a properly grounded outlet is notavailable. The temporary adapter shouldbe used only until a properly groundedoutlet (B) can be installed by a qualifiedelectrician. The green colored rigid ear,lug, or the like (F) extending from theadapter must be connected to a perma-nent ground (G) such as a properlygrounded outlet box cover. Wheneverthe adapter is used, it must be held inplace by a metal screw. NOTE: InCanada, the use of a temporary adapteris not permitted by the CanadianElectrical Code.

Carton Sntents ’

A B

Unpack deep cleaner from the.carton. _,I_

and identify the parts shown. Removeand dispose of the packing.

A. Deep cleanerB. Upper handle with powered hand toolC. Bolts (2)D. Nuts (3 - one extra included)E. Carpet/Upholstery DetergentF. Bare Floor Cleaner (some models)G. PreCIeaner. (some models) _H. Bare floor attachment:,

“.,.

. . _-’

Contained in carton with hose:‘-, I. Hose

‘,J. Stair/upholstery nozzleK. Tool rack and screw (taped on rack under nozzle)L. Hose holder ”M. Scrub moduleN. Nozzle clean-out tool (some models)

\ 0.. Crevicejtool (some models)“ ‘.*. ” ’

3

The assembled cleaner-will look like this.drawing.

.,

Place nuts in recessed areas on back ofhandle. Hold each nut in place whiletightening each bolt securely with aPhillips screw driver.

Only two nuts are needed on this model.The extra-nut is not required but hasbeen provided for your convenience.

Assemblehandle

Attach upper handleRemove clean solution tank (upper tank)from deep cleaner.

When handle sections are completelytogether, squeeze trigger (B) on upperhandle to snap trigger rod Inplace.

Witti cord hook (A) to back of deep cleaner,push upper handle down onto lower hanidIePush bolts into holes on front of han-dle. If bolts will not go tlirough hole e&i-ly handle is not pushed completelydowri.

Replace clean solution tank (uppertank) by positioning bottom first. Presson tank handle to snap top of tank intop l a c e .

4

Press cord into cord clip on back ofhandle. Pull cord tight.

Attachb* hose, holderPosition hole holder (C) onto handle bymatching tabs on rack with openings onback of handle. Make sure holes forbolts are aligned.

Place nuts in recessed areas on backof handle. Hold each nut in place whiletightening each bolt securely (from thefront of then handle) with a Phillipsscrew driver.Only two nuts are needed on thismodel. The extra nut is not required buthas been provided for your conve-nience.

Attach tool holderRemove tool and taped screw from rack.Insert projections on rack into slots onback of cleaner.

Slide rack down into place. Insert screw Storing hose & toolsat (D) and tighten with a Phillips screw-driver, Store hose on holder by first positioning

hose in front section of holder.

Continue wrapping hose over upper Position tool in holder at base of cleanerand snap It into place as snown at

..,.

arrow.

Insert end of bare floor attachment intoholder and snap into clip as shown.hose hook (E) and under lower hook (F).

Snap hose end fully into holder (G).Ensure that the hose end is pusheddown completely into holder (G).

The powered hand tool is shipped in aplastic bag for protection. Remove thebag before using the tool by first open-ing tool door.

To remove tool, pull it down and out-ward.To reposition the tool, reverse this proce-dure.

How to reattach toolcoverThe tool cover is designed with a break-away feature which allows it to snap freeif it is pushed open too far.

To reattach, align hinges of cover withslots on sides of tool storage area.

Push cover down to secure in place.

5

Deep cleaner description1. Hand grip2. Solution trigger: press to

release clean solution.3. Cord clip: place cord in clip

to keep it out of the waywhen using cleaner

4. Hose5. Hose holder: wrap hose

around holder and hosehooks (6) for storage.

6. Hose hooks7. Cord hooks: wrap cord

around hooks for storage.The top hook can be rotatedright or left for quick andeasy cord release.

8. Powered hand tool9. Carrying handle10. Clean solution tank handleIl. Clean solution tank cap/

measuring cup12. Clean solution tank: holds

cleaning solution.13. Recovery tank handle:

raise handle to unlock tankfor removal; lower handle forward to lock tank into posi-tion.

This deep cleaner is intended for household use.Operate deep cleaner only at voltage specified on data plate onEtck of cleaner. Plug deep cleaner Into a properly grounded out-

14. Recovery tank: holds dirtysolution.

15. Hood16. Brush speed selector:

slide selector to set brushspeed on HI, LO, or OFF.

17. Brush Indicator: spinswhen brushes are rotating.

18. Nozzle.19. Cleaning mode indicator:

choose either floor or tools2O.ON/OFF pedal21. Handle release pedal: step

on pedal to lower handle tooperating (floor) position;

22. Stair/upholstery nozzle23. Bare floor attachment24. Scrub module

ON/OFF pedal &Handle release pedalStep on pedal (A) to turn deep cleaneron. Step on pedal again to turn deepcleaner off.

Step on pedal (B) to lower handle tooperating position. Handle does not lockinto a single position but “floats” to allowconvenient operation.

6

Cleaning mode indicatorIndicator will show a green window nextto FLOOR (C) when handle is in theoperating position for cleaning carpetrugs and bare floors.

Indicator will show a green window nextto TOOL (D) when handle is in theupright position for tool use on stairsupholstery etc.

Deep cleaner automatically divertssuction from FLOOR to TOOL whenhandle is raised from the operating tothe upright position.

To transportTo move your deep cleaner from room toroom put handle in upright and lockedposition tilt deep cleaner back onwheels and push forward.

The deep cleaner may also be lifted byplacing a hand under the upper cleansolution tank handle as shown.

Automatic &&shut off I9When the recovery tank (lower tank) is fullthe automatic shutoff mechanism will shutoff the deep cleaner suction (suction willbe noticeably reduced).At that time the red float disk will rise tothe top of the recovery tank lid (E). Thedeep cleaner will no longer pick up dirtysoiution and the motor sound willbecome noticeably higher in pitch.

When this happens turn deep cleaneroff and empty recovery tank beforecontinuing use.

Check clean solution tank also; it mayneed to be refilled.

Brush speed selectorYour ‘SteamVac’ deep cleaner has threeagitator brush settings.HI - for normal cleaning of carpet andbare floorsLO - for gentle cleaning of carpets andbare floorsOFF - for cleaning carpets and barefloors when brushing is not desired.(Such as when picking up liquid spills,See page IO.)Slide selector button to the desired set-ting before cleaning.

Brush indicatorThe brush indicator will spin (F) whenthe deep cleaner is turned ON and thebrushes are rotating.If the indicator does not spin and thepattern is visible (G) when the deepcleaner is turned ON, the brushes arenot rotating.There are three reasons why the brushesmay not be rotating:

1. Brush speed selector set on OFF (seeprevious section).

2. Handle in upright position (see‘Cleaning mode indicator,” p, 6).

3. Brush indicator screen dirty.

To clean screen (H), turn deep cleaner offand disconnect from electrical outlet.

Remove clear cover and wipe off screenwith a damp cloth. Snap cover back intoposition.

The tanksClean solution tank(upper tank)The clean solution tank holds the clean-ing solution that is to be dispersed ontothe surface to be cleaned.

How to fillDisconnect deep cleaner fromelectrical outlet.Place deep cleaner handle in theupright, locked position.To remove tank, press down on handleand pull forward.Carry tank to a sink.

Continued +7

Rotate tank cap counterclockwise and liftup to remove cap.

Turn cap (A) upside down to serve as aIneasuring cup.

For heavy traffic areas:

Using cap, measure detergent followingthe chart below.For carpet, carpeted stairs and uphol-stery:Fill cap to fill line (5 ounces) with HOOVERCarpet/Upholstery Detergent.For bare floors:Fill cap to fill line (5 ounces) with HOOVERBare Floor Cleaner *Do not use Bare Floor Cleaner on carpet orupholstery. Do not use any type of waxwith your ‘SteamVac’ deep cleaner.

NOTE: Use only HOOVER detergents.They are specially formulated for usewith your ‘SteamVac’ deep cleaner.*Available at additional cost if not includedwith your model.

Pre-treat with HOOVER PreCleaner Spray.If you do not have access to the PreCleaner Spray, double the amountof HOOVER Detergent (use 2 capfuls or 10 ounces per 1 gallon tank).

CAUTION: Detergents containAnionic and Nonionic Surfactants.Avoid contact with eyes and skin. Incase of contact with eyes, flush withcold water for 15 minutes. In case ofcontact with skin, wash with water. IfIrritation persists, call a physician.For Medical Information (U.S.) calll-800-752-7869.

Pour detergent into tank. Fill tank tofill line (B) (1 gallon) with hot tapwater.

To assure proper performance, use onlyHOOVER cleaning detergent.

If rubber ring (C) on cap has becomedislodged, reposition it with uneven sideagainst ledge (D) as shown.

Replace cap. Rotate cap clockwiseuntil it locks In place. Cap must belocked In place for proper perfor-mance and to prevent leaking.

Position bottom of tank into unit andpress on tank handle to snap tank intoplace.

Recovery tank(lower tank)The recovery tank holds the dirty solu-tion that is picked up from the carpet.

When the recovery tank is full, the auto-matic shut-off will engage (see page 7)and the tank must be emptied.

How to emptyTurn deep cleaner off and disconnectfrom electrical outlet.To prevent possible leaking, removeclean solution tank (Fig. 2-10) by press-ing down on tank handle and pulling for-ward; set tank aside (do not set tankon furniture).Step on handle release pedal (Fig. 2-2)and lower handle until it rests on thefloor.

8

Raise handle to carrying position To remove tank lid, lower handle com-(straight up) to unlock tank from base ofdeep cleaner. Lift tank from deep clean-er and carry it to a sink or drain.

pletely toward back of tank and lift offlid.

Empty the tank and reposition the lid.

For full suction, it is important thatthe recovery tank lid is properlysecured before cleaning.

Raise tank handle to carrying position toplace it into base of cleaner. Move han-dle completely forward to lock tank intoplace (see Fig. 2-17).

Raise handle of deep cleaner to uprightposition and reposition upper cleansolution tank.

Before you begincleaninga. Vacuum thoroughly - For carpet, usea vacuum cleaner with an agitator forbest results. Vacuum upholstery with avacuum cleaner with cleaning toolattachments. Use a crevice tool to reachinto tufts and folds. Do not use the‘SteamVac’ deep cleaner as a dry vac-uum cleaner.b. For upholstery, check cleaningcode - Use your HOOVER ‘SteamVac’deep cleaner only if the upholstery fab-ric is marked with a “W” (for “wet” clean)or “S/w” (for “solvent/dry” or “wet”clean). Do not clean fabric marked “S”(“solvent/dry” clean only). If yourupholstery does not have a code, seekprofessional assistance.

c.Test for colorfastness - Mix detergentand water according to the instructionsunder “Fill clean solution tank” on pages 7

and 8. Wet a white absorbent cloth with thesolution. in a small, hidden area, gently rubthe surface with the dampened cloth. Wait tenminutes and check for color removal or bleedwith white paper towel or cloth. If surface hasmore than one color, check all colors.

d. When cleaning entire floor, movefurniture out of area to be cleaned(may not be necessary if only high trafficareas are to be cleaned). For furnituretoo heavy to move, place aluminum foilor wax paper under legs. This will pre-vent wood finishes from staining carpet.Pin up furniture skirts and draperies.

e. Pretreat spots an.d heavy trafficareas with HOOVER@ PreCleaner*-Test PreCleaner for colorfastness by firstspraying it on a hidden area; wait tenminutes and blot with white paper tawelsor cloth.If no color change is visible, sprayPreCleaner onto spots and traffic areas. Waitat least ten minutes. Use your ‘SteamVac’deep cleaner to pick up PreCleaner andspot. Repeat until spot is removed; carefullyscrub with a household scrub brush if nec-essary

Do not saturate carpet or upholstery withPreCleaner.If you do not have access to thePreCleaner Spray, double the amountof HOOVER Detergent (use 2 capfulsor IO oz. per 1 gallon) in the cleansolution tank.No cleaning solution removes all stains fromall carpets. Stain removal varies with thetype of spill, time elapsed before removal,carpet material, and carpet type.

f.To prevent staining, use plastic or alu-minum foil to protect wood or metal sur-faces from possible water spray.

g. To avoid wetting and possible damageto wood floors underneath area rugs/car-pet, either move area rugs/ carpet to a non-wood bare floor surface or place waterproofmaterial (e.g. plastic) underneath thembefore cleaning.

See pages IO-13 for instructions on variouscleaning tasks.

*Available at additional cost if not includedwith your model.

After cleaninga. Allow carpet or upholstery to dry. Tohelp prevent matting and resoiling thecarpet, keep children and pets awayfrom surface until it is completely dry. Ifit is necessary to walk on damp car-pet, place towels or white cloths on thetraffic areas.If furniture must be replaced before thecarpet is dry, use plastic or aluminumfoil pads under legs of furniture so metalslides or wood finishes will not stain thecarpet.b. If desired, the carpet may be rinsed,Rinsing is not necessary for cleaning,but it may Improve the surface’s appear-ance after it is dry.If rinsing is desired, be careful not toover-wet the carpet or upholstery.

Allow time for carpet or upholstery todry completely between cleaning andrinsing. To rinse, follow the same proce-dure for cleaning only using hot tapwater with no detergent in the upperclean solution tank.c. Empty tanks, rinse with clear waterand let air dry. Rinse the solution tankcap and recovery tank lid and let air dry.

d. Remove debris from recovery tank fil-ter and rinse with clean water.

Note: If the filter must be removed forcleaning, it is easier to replace if the fil-ter is wet.

e. If desired, vacuum thoroughly aftercarpet has completely dried. This willhelp reduce any shading left by thedeep cleaner’s brushes.

To clean nozzleIf lint or other debris becomes lodged innozzle, do not attempt to removenozzle cover.Pour one to two cups of clear water on anon-carpeted floor. Do not pour wateronto a wood floor.Pick up water with your ‘SteamVac’ deepcleaner. Repeat as necessary untildebris is flushed out of nozzle.

Continued + -9

Some models have a nozzle clean-outtool for removing debris or if a non-car-peted floor is not available. To use thetool: Disconnect deep cleaner fromelectrical outlet. Slide tool into nozzleand remove debris as shown.To clean the outside of the machine,wipe off dirt with a cloth dampened inwarm water and mild detergent. Do notuse solvent or petroleum based prod-ucts to clean the machine.

Read “Before you begin cleaning”instructions on page 9.1. Fill clean solution tank (upper tank)with HOOVER Carpet/UpholsteryDetergent according to instructions forFigs. 2-10 to 2-16.

2. Move speed selector to LO for gen-tle cleaning or HI for normal cleaning.3. Dry hands and plug cord into a prop-erly grounded outlet.Do not clean over floor electrical out-lets.4. To avoid walking on damp carpet,start at the end of the room farthest fromthe door or path to sink where tanks willbe emptied and filled

Step on handle release pedal and lowerhandle to operating position; turn deepcleaner ON.5. Squeeze trigger to release cleaningsolution and slowly push deep cleanerforward (equals one wet stroke).

6. Continue to squeeze trigger andslowly pull deep cleaner back towardyou (second wet stroke). Release triggerand slowly push deep cleaner forwardover area just sprayed with solution (drystroke). Then slowly pull deep cleanerback toward you without squeezing trig-ger (dry stroke).

7. Overlap strokes by 1 inch to help pre-vent streaking.Keep nozzle flat on floor for both for-ward and reverse strokes.For heavily soiled areas, repeat steps 58. To avoid saturating carpet, do notuse more than 4 wet strokes over onearea. Always end with dry strokes.It is best to alternate wet and drystrokes as described above.For best cleaning results and to aid infaster drying of carpet, end with moredry strokes. (Continue using dry strokesuntil little water is visible passingthrough the recovery tank lid.)Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see“Automatic shut-off”, page 7)When finished cleaning, follow “Aftercleaning” instructions on pages 9-10.

Your HOOVER SteamVac deep cleanermay also be used to pick up small liq-uid spills (1 gallon or less, never toexceed l/4 inch in depth) on carpet,upholstery, or bare floors.

1. For best results, pick up spills immediately by placing the stair/upholsterynozzle just above the spill and suctionup any residue on top of the carpet.2. If the spill remains, place either thestair/ upholstery nozzle or floor nozzlewith brushes turned OFF in front of thespill, pull the nozzle very slowly overthe spill initially with suction only. Repeatwith spray and suction.

When picking up spills on bare floors,use only the floor nozzle with the barefloor attachment in place and speedselector in the OFF position (this will helpprevent spreading the spill).

If a spot is left, the stair/upholstery nozzle isgenerally more effective for removing it.Although no cleaning solution can com-pletely remove all spots, they can be treat-ed by following the instructions provided bythe manufacturer of the carpet, upholsteryor bare floor surface being cleaned.

Do not use the SteamVac deep cleanerto pick up flammable or combustible liq-uids or chemicals.When finished, follow “After cleaning”instructions on pages 9-10.

How to attach bare floorattachmentDisconnect deep cleaner from electri-cal outlet.To prevent possible leaking, removeclean solution tank and recovery tankbefore positioning bare attachment.Refer to Fig. 2-10 to remove clean solu-tion tank. Set tank aside (do not settank on furniture).

Refer to Fig. 2-17 to remove recoverytank.

With handle in upright position, tiltcleaner back so that handle rests onthe floor.

With foam strip (A) (located under thenetting) in position as shown, placeattachment on front of nozzle (B).Make sure arrow on end of attachmentpoints in the direction as shown.

IO

Push attachment against nozzle while rotat-ing attachment downward until both endssnap into place.

(Note: Some force may be required torotate and snap attachment into place.)

Return deep cleaner to upright position.Lower handle and replace recoverytank.

Raise handle to upright position andreposition clean solution tank.

To clean floorRead Before you begin cleaninginstructions on page 9.Do not use the SteamVac deep clean-er on hardwood floors.Fill clean solution tank with HOOVERBare Floor Cleaner (available at additionalcost if not included with your model)according to instructions on pages 7and 8.

Do not use any type of wax with yourSteamVac deep cleaner.

Move speed selector to the Lo or HIposition for scrubbing or OFF-ifscrubbing is not desired.Dry hands and plug deep cleaner intoa properly grounded outlet.Step on handle release pedal and lowerhandle to operating position; turn deepcleaner ON.

To release solution, press trigger. Slowlymove deep cleaner forward and back-ward over area to be cleaned.

To pick up dirty solution, release triggerand slowly move deep cleaner overarea where solution has just been dis-persed. Use both forward and reversestrokes.

Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see“Automatic shut-off”, page 7)

When finished cleaning, follow “Aftercleaning” instructions on pages 9-10.

Remove attachment from nozzle andrinse in clear water. Do not removeplastic screen or foam from attach-ment.

B. Stair/upholstery nozzle has a built-inbrush to help provide the scrubbing

1

action some spots may need forremoval.C. Scrub module with detachablescrub pad attaches to the base of thepowered hand tool (in place of brushmodule). Can be used to scrub stub-born areas such as scuff marks, driedspills, and in hard to reach areas onhard surfaces.D. Crevice tool (included with somemodels) can be used to clean alongedges of carpet, carpeted stairs, and onupholstery.

Your model includes some combinationof the following tools.A. Powered hand tool has rotatingbrushes for extra scrubbing action onsmall carpet areas, carpeted stairs andupholstery. Brushes can be removed forconverting to the scrub module.

How to attach toolsDisconnect deep cleaner from electri-cal outlet.1. Place handle in upright position andremove hose from rack.

Before using toolIt may be necessary to remove air fromthe system (“prime the pump”) so theclean solution will flow to the tool. Followthese steps:1. Attach tool to hose and turn the deepcleaner ON.2.Put the tool on a hard surface oragainst your hand to block off the suc-tion3. Wait a few seconds (can take up to15 seconds). Then squeeze the triggerand begin cleaning.Follow the instructions on pages 12-13for the appropriate cleaning task.

Attaching scrub module1. Grasp the sides of the brush moduleand lift it from the base (C).2. Snap scrub module onto the baseNote: It may be necessary to rotate thescrub module (D) slightly so it will alignproperly to the base.

All tools connect to the hose in the samemanner.2. Connect tool to end of hose by, slidingit onto connector until the tab (A) locks itsecurely.Using your thumb, push forward andup on the latch (B) to remove tool asshown.

Using the scrub toolWith a little solution, test the scrub

tool on a hidden area before using onthe desired surface. If no surfacechange is visible, continue to use asdescribed below.1, Fill clean solution tank with HOOVERBare Floor Cleaner* according to instruc-tions for Figs. 2-10 to 2-16.2. Hold scrub tool above area to becleaned and press trigger to dispensesolution.3. Release trigger and scrub area withtool. Pick up dirty solution withsqueegee as shown.*Available at additional cost if not includ-ed with your cleaner.

After using scrub toolTo clean scrub pad, pull it off module.Wash it in water with mild detergent.Rinse and let air dry.

Replacement pads may also be pur-chased. Ask for HOOVER part no.40308001.

5. Drain solution tube (located insidehose) by pointing end of hose in sinkand pressing trigger.

6. Proceed with steps c, d, and e, for“After cleaning” on page 9.

After using tool1. Follow steps a and b for “After clean-ing” on page 9.

2. Rinse tool and hose by filling sink witha small amount of water. Turndeep cleaner ON and pick up the waterwith the tool.3. Drain hose by turning deep cleanerON and holding end of hose up for sev-eral seconds. Do not press trigger.

4. Disconnect deep cleaner from electri-cal outlet.

Read “Before you begin cleaning”Instructions on page 9.Place handle in upright position.Agitator brushes will not rotate whilehandle Is in upright position.Fill clean solution tank with HOOVERCarpet/Upholstery Detergent accordingto instructions on pages 7 and 8. Attachtool to end of hose.

Hose length may require that machinebe placed at the top of the stairs toclean upper half of stairway and at bot-tom of stairs to clean lower half.

To prevent machine from falling, useextra caution when cleaning on stairs.Do not place deep cleaner on stairs.Do not point tools toward people orpets. Dry hands and plug deep cleanerinto a properly grounded outlet.

12

Turn deep cleaner ON.

Pre-spray the carpeted stair by holdingthe tool (A) or (B) about one inch abovethe carpet and push it forward whilepressing the trigger (equals one wetstroke).Position tool against the riser and slightlypress it into carpet pile. Press the triggerand pull the tool slowly over the carpet(second wet stroke). Release trigger at endof stroke.

If additional cleaning is necessary, waituntil the carpet is completely dry beforeusing the tool again.

Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, page 7)

When finished cleaning, follow “Aftercleaning” instructions on page 9 and“After using tool” instructions on page12.

Lift tool, and position it against riser. Pulltool slowly over carpet without pressingtrigger (dry stroke).

It is best to alternate wet and dry strokesas described above. End with more drystrokes to aid in faster drying of carpet.

Overlap strokes by l/2 inch to help pre-vent streaking.

To avoid saturating carpet, do not usemore than 4 wet strokes over any onearea. Always end with dry strokes.

Read “Before you begin cleaning”Instructions on page 9.Be sure to check the cleaning code onyour upholstery. Use your HOOVER‘SteamVac’ deep cleaner only onupholstery marked “W” or “W/S”.Place handle in upright position.Agitator brushes will not rotate whilehandle Is In upright position.Fill clean solution tank with HOOVERCarpet/Upholstery Detergent accordingto instructions on pages 7 and 8. Attachtool to end of hose.

Do not point tools toward people orpets.Dry hands and plug deep cleaner into aproperly grounded outlet.

Turn deep cleaner on.

Gently press the tool (A) or (B) onto thefabric. Press the trigger and slowly pullthe nozzle over the fabric,

the trigger to remove more moisture.

To clean in corners or creases, lift thetool one-half inch from the fabric andpress the solution trigger.

Vacuum up the solution with the toolwithout pressing the trigger.

Overlap strokes by l/2 inch to help pre-vent streaking.

Make additional strokes without pressing

For heavily soiled areas, it may be nec-essary to repeat the cleaning process.Make crisscrossing strokes to the origi-nal pattern; overlap each pass,

Make no more than 2 passes with thesolution over any one area to preventover-wetting and damage to fabric.If additional cleaning is necessary, waituntil the upholstery is completely drybefore using the tool again.

Empty recovery tank when the motorsound becomes higher pitched andthere is a loss in suction (see “Automaticshut-off”, page 7).

When finished cleaning, follow “Aftercleaning” instructions on page 9 and“After using tool” instructions on page 12.

Removable brushesYour deep cleaner is equipped withremovable brushes for easy cleaning.

To remove brushesDisconnect cleaner from electricaloutlet.To prevent possible leaking, removeclean solution tank and recovery tank.Set tanks aside.

Press handle release pedal to lower han-dle. Turn cleaner over so bottom is fac-ing up.

Grasp inner portion of brush (A) andpull brush assembly out slightly toreveal latches (B).

Press all four latches (B) and pull brushblock out. The brushes can be cleanedunder running water.

13

To replace brushes Press brush firmly to snap into place.Align posts (C) on both ends of brushassembly with slots (D) in cleaner hous-ing.Make sure that the square post (E) alsoaligns with the square hole (F). Turnbrushes slightly until post fits easily intohole.

StorageBefore storing:

l Empty solution tank and rinsethoroughly with clean water.

l Replace empty solution tank andturn deep cleaner ON. Squeezetrigger and push deep cleaner for-ward and back several times toexpel any solution remaining in thedeep cleaner’s system. (Do not use

deep cleaner on wood floors.)

l Empty recovery tank and rinsethoroughly with clean water.

Allow brushes and underside of deepcleaner to air dry thoroughly beforestoring deep cleaner on a carpeted orwood surface.Do not store deep cleaner with a fullsolution tank In place.

.,

LubricationThe motor Is equipped with bearingswhich contain sufficient lubrication forthe life of the motor. The addition oflubricant could cause damage. Do notadd lubricant to motor bearings.

ServiceTo obtain approved HOOVER serviceand genuine HOOVER parts, locate thenearest Hoover Factory Service Centeror Authorized Hoover WarrantyService Dealer (Depot) by:

l checking the Yellow Pages underVacuum Cleaners - Household” OR

l checking the list of Factory ServiceCenters provided with this cleanerOR-

* calling i-800-944-9200 for anautomated referral of authorizedservice outlet locations (U.S. only)OR-

* checking the Service section of TheHoover Company on-line atwww.hoover.com

Please do not send your cleaner to TheHoover Company in North Canton forservice, this will only result in delay.

If further assistance Is needed, contactThe Hoover Company ConsumerResponse Center, North Canton, Ohio44720 Phone: l-330-499-9499.

In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8,.Phone: l-800-263-6376.

Always identify your cleaner by thecomplete model number when request-ing information or ordering parts. (Themodel number appears on the bottom ofthe cleaner.)

14

If a minor problem occurs, it usually canbe solved quite easily when the cause isfound by using the check list below.

Possible causePossible solution

l Not firmly plugged inl Plug unit in firmly

l No voltage In wall plugl Check fuse or breaker

* Blown fuse/tripped breakerl Replace fuse/reset breaker

Possible causePossible solution

l Recovery tank full/automaticshut off engaged

l Remove and empty recovery tank

-* Blockage In tool on end of hosel Remove tool and clear blockage

l Recovery tank lid not oncorrectly

* Make sure lid is on securely

Possible causePossible solution

l Solution tank not firmly in placel Make sure tank is securely locked in

position

l Solution tank emptyl Refill tank according to instructions for

surface being cleanedl Recovery tank lid not on

correctlyl Make sure lid is firmly in placel Pump needs to be “primed” (when

using tool)l See ‘Before using tool” section, p. 11

Possible causePossible solution

l Indicator screen dirty9 Remove clear cover over indicator

and clean screen; replace cover

l Speed selector on OFFl Move speed selector to Low or Hi

Full One YearWarranty

(Domestic Use)

Your HOOVER@ appliance is warrantedin normal household use, in accordancewith the Owner’s Manual against originaldefects in material and workmanship fora period of one full year from date of pur-chase. This warranty provides, at no costto you, all labor and parts to place thisappliance in correct operating conditionduringJhe warranted period. This war-ranty applies when the appliance is pur-chased in the United States including itsterritories and possessions, or in Canadaor from a U. S. Military Exchange.Appliances purchased elsewhere arecovered by a limited one year warrantywhich covers the cost of parts only. Thiswarranty does not apply if the applianceis used in a commercial or rental appli-cation.

Warranty service can only be obtainedby presenting the appliance to one ofthe following authorized warranty serviceoutlets. Proof of purchase will berequired before service is rendered.

1. Hoover Factory Service Centers.

2. Hoover Authorized WarrantyService Dealers (Depots).

For an automated referral of autho-rized service outlets in the U.S.A.,phonel-800-944-9200 ORvisit The Hoover Company on-line atwww.hoover.com

This warranty does not cover pick updelivery, or house calls; however, if youmail your appliance to a Hoover FactoryService Center for warranty service,transportation will be paid one way.

While this warranty gives you specificlegal rights, you may also have otherrights which vary from state to state.

If further assistance is needed, or ifthere are questions concerning this war-ranty or the availability of warranty ser-vice outlets, write or phone theConsumer Response Center, The HooverCompany, 101 East Maple St., NorthCanton, Ohio 44720. Phone 1-330-499-9499.

In Canada, contact Hoover Canada,Burlington, Ontario L7R 4A8,l-800-263-6376.

15