i Text Sharp Single

2
Calculation results Customer name: ZADCO Reference: EGT Vent fan belt drive Comment: Selection base on application & service factor Input data: Rated power [kW] 132 Rated torque [Nm] 875.35 Requested service factor 1.3 Driver speed [r/min] 1440 Driven speed [r/min] 1611 Drive: Overall width [mm] 120 Overall length [mm] 1590.89 Overall height [mm] 362 Pulley center distance [mm] 1248.89 Span length [mm] 1248.73 Actual driven speed [r/min] 1610.4 Belt: Designation PHG SPB3550XP Number of belts 6 Actual service factor 1.38 Belt power rating [kW] 181.93 Belt mass [kg] (Aprox.) 0.8 Belt width [mm] 16.00 Driver pulley: Designation PHP 6SPB355TB Reference diameter [mm] 355 Nominal taper lock PHF TB3535X...MM Taperlock shaft diameter range [mm] 35 -- 90 Driven pulley: Designation PHP 6SPB315TB Reference diameter [mm] 315 Nominal taper lock PHF TB3535X...MM Taperlock shaft diameter range [mm] 35 -- 90 Hub loads: Static hub loads for NEW belt [N] 14368.27 Static hub loads for RUN-IN belt [N] 9578.85 Dynamic hub loads for NEW belt [N] 12369.21 Dynamic hub loads for RUN-IN belt [N] 7579.79 Tensioning: Installation strand tension for NEW belt [N] 1197.36 Installation strand tension for RUN-IN belt [N] 798.24 Deflection forces for SKF Belt tension pen gauge [kg] NEW 7.77 RUN 5.23 Vibrating frequency for SKF Belt Frequency Meter [Hz] NEW 29.21 RUN 23.85 Date: 09/08/2011 ® SKF is a registered trademark of the SKF Group. © SKF 2011 The contents of this report are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted. Every care has been taken to ensure the accuracy of the information contained in this report but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein. 1/2 SKF Belt Frequency Meter (PHL FM 10/400) Belt tension pen gauge (PUB PSD C1/007)

description

i Text Sharp Single

Transcript of i Text Sharp Single

  • Calculation resultsCustomer name: ZADCOReference: EGT Vent fan belt driveComment: Selection base on application & service factor

    Input data:Rated power [kW] 132Rated torque [Nm] 875.35Requested service factor 1.3Driver speed [r/min] 1440Driven speed [r/min] 1611

    Drive:Overall width [mm] 120Overall length [mm] 1590.89Overall height [mm] 362Pulley center distance [mm] 1248.89Span length [mm] 1248.73Actual driven speed [r/min] 1610.4

    Belt:Designation PHG SPB3550XPNumber of belts 6Actual service factor 1.38Belt power rating [kW] 181.93Belt mass [kg] (Aprox.) 0.8Belt width [mm] 16.00

    Driver pulley:Designation PHP 6SPB355TBReference diameter [mm] 355Nominal taper lock PHF TB3535X...MMTaperlock shaft diameter range [mm] 35 -- 90

    Driven pulley:Designation PHP 6SPB315TBReference diameter [mm] 315Nominal taper lock PHF TB3535X...MMTaperlock shaft diameter range [mm] 35 -- 90

    Hub loads:Static hub loads for NEW belt [N] 14368.27Static hub loads for RUN-IN belt [N] 9578.85Dynamic hub loads for NEW belt [N] 12369.21Dynamic hub loads for RUN-IN belt [N] 7579.79

    Tensioning:Installation strand tension for NEW belt [N] 1197.36Installation strand tension for RUN-IN belt [N] 798.24Deflection forces for SKF Belt tension pen gauge [kg] NEW 7.77 RUN 5.23Vibrating frequency for SKF Belt Frequency Meter [Hz] NEW 29.21 RUN 23.85

    Date: 09/08/2011

    SKF is a registered trademark of the SKF Group. SKF 2011The contents of this report are the copyright of the publisher and may not be reproduced (even extracts) unless permission isgranted. Every care has been taken to ensure the accuracy of the information contained in this report but no liability can beaccepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.

    1/2

    SKF Belt Frequency Meter(PHL FM 10/400)

    Belt tension pen gauge(PUB PSD C1/007)

  • Drive layout BeltPHG SPB3550XPWedge SPB XPBelt marking SPB3550

    XPNo. of ribs 1Pitch length (mm) 3550Effective length(in)

    139.8

    Width (mm) 16.3Height (mm) 13

    Driver pulleyPHP 6SPB355TBPitch diameter(mm)

    355

    Outside diameter(mm)

    362

    Pulley type 5Bush no. 3535Min. bore (mm) 35Max. bore (mm) 90F 120E G 312K 15.5L 89M 15.5H 191Weight (lbs.) 28.3

    Driver bushingPHF TB3535X...MMNo data

    Driven pulleyPHP 6SPB315TBPitch diameter(mm)

    315

    Outside diameter(mm)

    322

    Pulley type 5Bush no. 3535Min. bore (mm) 35Max. bore (mm) 90F 120E G 272K 15.5L 89M 15.5H 191Weight (lbs.) 24.1

    Driven bushingPHF TB3535X...MMNo data

    SKF is a registered trademark of the SKF Group. SKF 2011The contents of this report are the copyright of the publisher and may not be reproduced (even extracts) unless permission isgranted. Every care has been taken to ensure the accuracy of the information contained in this report but no liability can beaccepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.

    2/2