VF-8/50 I • • j 2X 29" (737 mm)

--1-_ L _ �. -------t-------r- : ' ' 26'"' : :

(660 mm): : sa· 1--f- -e � 0 -�

(1473 mm) T : �

_l _____ L. � o i 84"

§ : � '

No te: Foundation must e xtend a t least 1 ft. (305 mm) from bored holes.

(2134 mm) : :

I : : 8X01.5 x8 .5" DP _ t ________ L-, ...-r(8X038x216 mm DP)

: _J ___ Machine Front ___ L_ l 137"

116" (2946 mm)

(3480 mm)

Haas Technical Publications

0

54• (1372 mm)

14" --- (356 mm)

125" (3175 mm)

' ' -i 58" (1473 mm) i-- Leveling Pad Pin Dimension

VF-8 Anchor Pattern This anchor pattern applies for machines

built after January 2013.

•• Extended Z-Axis Clearance Optionadd 8" (203 mm)

141" (3581 mm)

Max. Operating Height ••

G) Electrical Connection

@ Air Connection

Two Step Operator Platfonn included (not shown) Length: 72.5" (1842 mm) Width: 23.5" (570 mm) Height 12.5" (318 mm)

30+1 SMTC 125"

(3175 mm) ••

189" (4801 mm)

159" (4039 mm)

�· 50" 4•

(102 mm)

t ♦

j j I I

,-� �,.___________.,I-F==--4-------'-1=-----+.L�-----{2

''T'

41" (1041 mm)

+ t

2X 16.93" (430 mm )

1-----2X 14.76"

(374.9 mm) 2X9.84" J_ l (249.9 mm) - ----f--l-

-

36.00" (914 mm)

'Z' 2X4.9 (125 m m)

43.93" (1116 mm) -

-2x3.1S" (80 mm)

. .

. .

�.

64.00" (1626 mm)

.

..

. .

2X 3.94" (100

rm)

f

• 2X8. (221

69" mm)

� -----1

Del

(1

57.5" (1461 mm)

130" (3302 mm)

96" (2438 mm)

t

61" (1549 mm) Door Ope ning

///////////////////////////� 56" (1422 mm _ •• ..-;---+1-------�

t Door :: 36" 2X 28" _9Pen :: (914 mm)

(711 mm) ax ::

58" (1473 mm) 165"

(4191 mm) Max.

l

-- 58" (1473 mm)

84" (2134 mm)

0.828+.002"

� 0 515" cru•���:r .40" (10 mm)

1.06" (27 mm)

Section A-A {16X)

.630"-.635" (16 mm)

Detail B (7X)

VF-8 Table Dimensions �

2.0" ;..,' f----64"(1626 mm)----l--tl r

(51 m�m

_> __________ �----,---�---------+--� -----------------------------r--------------------------- 1

--+--

-�

t ' ' ' '' '' '' '' '' ' : ' : : 2X� , : (51 mm)

40• (1016 mm)

Tool Ga e Line

30.5" (775 mm) Minimum

' ' I-I- 12.4" (315 mm) SMTC 30

Side - Mount Tool Change r Anm ' '

� t

2!r (737 mm) Minimum

-�--�---�, -

-

3�fo_----�,�--��=��-=-�--T �-

t , � - ,- (762 mm) (889 mm)

♦

83" (2108 mm) l_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=_=:_=:;b======-=-:=-=-=-=-=-=-:-=-==:i-==-----"�-_,_

Tool Change Position,,/�'', ZT-r!".eis

l c1i; ;m) Max. Z-Axis

6 8" (173 mm) / \1 u•

Clearance to Tabl e

.L_�-'-------+----+-~ -_ -_ ___,_,_.., _-----���-------'-�07.9" (201 mm) Spindl e

t �---��,---------�

---------------------------

&. 5.o.J (127 mm)

NOTES:

2X 13" _.., (330 mm)

\ MILL TABLE (at home position) SIZE: 64" x 36" (1626 mm x 914 mm) TRAVEL: 64" x40" (1626 mm x 1016 mm)

154" (3912 mm) Enclosure Usable Work Space

1. TABLE POSITION(S)AT MAX X & Y TRAVELS. 2. MEASUREMENTS ARE FROM THE EDGE OF Mill TABLE TO N EAREST

OBSTRUCTION (ie. ENCLOSURE, WAY COVER, DOORS, ETC.). &DIMENSIONS ARE REDUCED AS HEIGHT ABOVE TABLE INCREASES;

i e . FRONT OF ENCLOSURE IS SLOPED 5• INWARD FROM BOTTOM TO TOP . DIMENSIONS SHOWN ARE AT TABLE TOP HEIGHT.

Top View

\ ' '

7.75" (196.9 mm)

i-------:-17 .30" Programmable

c'

I I

I l439.4 mm r Coolant

I �"'"('M, mm)

t I� � 12.5".. �

�:::::�------�;• "i,�;;;:.;.-::z','1:',1l:l�m)

�� L _____ _ Detail C

Front View VF-8/50 Layout Drawing Revision E

VF-8/50 Enclosure Usable Work Space July, 2016

*Due to continual product improvements, machine dimensions are subject to change without notice.