Hyundai / Mitsubishi FWD Transmission I.D. Chart · 2018. 10. 8. · KM177 2 Piece 4 Spd L/Up Cast...

7.3

MITS

UB

ISH

I

Code Number on rear of case.

Code Number on top of case.

Hyundai / Mitsubishi FWD Transmission I.D. Chart

Old Code New Code Case Type Transmission Type NotesKM170 2 Piece 3 Spd Non L/Up Cast # 170-1 On Inside Rear Of BellKM171 2 Piece 3 Spd L/Up Cast # 171 On Rear Of CaseKM171-5 F3A21 2 Piece 3 Spd L/Up Cast # S-KM171 Or F3A21-SKM172 2 Piece 3 Spd L/Up Cast # 175 On Rear Of CaseKM172-5 F3A22 2 Piece 3 Spd L/Up Cast # F3A22KM175 2 Piece 4 Spd L/Up Cast # 175 On Rear Of CaseKM175-5 F4A22 2 Piece 4 Spd L/Up Cast # S-KM175 Or F4A22KM176-5 F4A21 2 Piece 4 Spd L/Up Cast # KM176KM177 2 Piece 4 Spd L/Up Cast # 177KM177-8 F4A23 2 Piece 4 Spd L/Up Cast # 177 Or F4A23F4A32 A4AF 1 Piece 4 Spd L/Up Cast # A4AF-1 Or A4AF-2 On Rear Of CaseF4A32 A4BF 1 Piece 4 Spd L/Up Cast # A4BF On Rear Of Case

F4A33 1 Piece 4 Spd L/Up Cast # F4A33EN, F4A33EV, F4A33EVSF4A41 2 Piece 4 Spd L/Up Cast # F4A41F4A42 2 Piece 4 Spd L/Up Cast # F4A42F4A51 2 Piece 4 Spd L/Up Cast # F4A51W4A32 1 Piece 4 Spd L/Up AWD Cast # W4A32W4A33 1 Piece 4 Spd L/Up AWD Cast # F4A33, F4A33ENS Or W4A33F5A51 2 Piece 5 Spd L/Up

JP (Automatic Transmissions) Ltd Tel +44 (0) 1934 852772 [email protected] www.jpat.co.uk

7.4

MIT

SU

BIS

HI


KM170 thru KM177-8 FWD 3 & 4 Speed

D

C

E

B

A

42

311 310 211*228*

046 555

Direct Drum

070 034 510530

313036

520

179

StatorPump Body777 778

500

750 318

078

774

848

Bell Hsg.

896

909

360869

907B

366194

907906

905

760

Case

996

378

010326

300

765

692

781

964 974 877334335 231

881149 106 128

Forward Clutch

146 878*232

574234

251

Forward Hub

564

369

052614

182 052

Rev. Sun Gear

Forward Sun Gear

241242

056 612 056247

654 584 594

Rear Planet Ring Gear

583

251252

889060

604 268 710 894271

347

342

740

Servo

989

Low / Rev Sprag

895

605

Drive

420

Valve Body

V.B.Parts

741

779

437

Pump Parts

507

195

7.5

MITS

UB

ISH

I


FWD 3 & 4 Speed

A

B

C

D

E

KM170 thru KM177-8

42

567155 114 134 154

Low / Reverse ClutchKickdown Band

994

410

041 675 570220 861* 140 100 120214

O.Dr. Clutch

O.Dr. Hub

862863

970 960

560185

730 273275

273 274 712 796 375 686

693

Pinion

076 288 289

716 720 292 291 076

Differential

715284 283 714 283 679 374

IdlerDiff.

Parts

717

274

Driven

282282

Neutral Switch

349

493

687

780

436

786

336337 965 975 879

565046 126 106 146 878*

230229

554

Direct Clutch Forward Drum

177 358670

Input Shaft

022 885* 630

386

044

Center Support

995

Park PawlLinkage

991

330 331550 083

223304 762

O.Dr. DrumO.Dr. Cover

181

622

Shell / Kickdown Drum

339338

967 857 977 893

7.6

MIT

SU

BIS

HI


339338

311 310 211*228*

046 555

Direct Drum

070 034 510530

313036

520

179


500

Pump Parts

507

336337 965 975 879

565046

149 106 128

Forward Clutch

146 878*232

574234

251

Forward Hub

567

Kickdown Band

022 885* 630

386

044

Center Support

622


967 857 977 893

A4AF3 / A4BF2 FWD 4 Speed

42

060604

796710268

692 268 041 675 570220

O.Dr. Hub

219

076289 716 720 292 076

715

Diff.Parts

717

786

725

Differential726

794

300

765

779Valve BodyV.B.Parts

741740

436

437

010

326420906

907

909

896

360 896

907B195

194195905

Servo

410760

303

758

774

436L

370

369

761CaseParts

494 493

347

342

268-1 268-1

Drive

348

Retainer

A

B

C

D

E

7.7

MITS

UB

ISH

I


126 106 146 878*230

229554


177 358670

Input Shaft

181 964 974 877334335 231

881564

155 114 134 154

Low / Reverse Clutch

614182 052

Rev. Sun Gear

Forward Sun Gear

241242

056 612 056247

654 584 594


583989

Low / Rev Sprag

052251

252889

FWD 4 Speed A4AF3 / A4BF2

42

861*

140 100 120

O.Dr. Clutch

214 330 331550 083

223

O.Dr. Drum

185960970560

730 273275

281 280712

796

Pinion

274

Driven

898

995

Park Pawl

994991

Linkage

992

349

771 686

304762

862

375

SpacerPlate O.Dr. Cover

A

B

C

D

E

7.8

MIT

SU

BIS

HI


339338

311 310 211*228*

046 555

Direct Drum

070 034 510530

313036

520

179


500

Pump Parts

507

336337 965 975 879

565046

149 106 128

Forward Clutch

146 878*232

574234

251

Forward Hub

567

Kickdown Band

022 885* 630

386

044

Center Support

622 967 857 977 893

268 271605

604

076289 716 720 292

715

Diff.Parts

717

786Differential

726794

436

410

710 894895

Drive


760

303

758

692

781

219

906

907

909

896

360 896

907B195

194195905

Servo

774

Valve Body

010

326420

300

765

779

740

V.B.Parts

741

437

A4AF1 / AFAF2 / A4BF1 FWD 4 Speed

436L

370

369

761Case Parts

494 493

347342

D

C

E

B

A

42

7.9

MITS

UB

ISH

I


126 106 146 878*230

229554


177 358670

Input Shaft

181 964 974 877334335 231564

155 114 134 154


614182 052

Rev. Sun Gear

Forward Sun Gear

241242

056 612 056247

654 584 594


583989

Low / Rev Sprag

052251

252889

076725

041 675 570220861* 100

O.Dr. Hub

120

O.Dr. Clutch

862863

970 960330 331

550 083

O.Dr. Drum

214

560185140

730 273275

273 274712

796

Pinion

274

Driven

762

223

995

Park Pawl

994991

Linkage

992

349

FWD 4 Speed A4AF1 / AFAF2 / A4BF1

Retainer

348

O.Dr. Cover

D

C

E

B

A

42

7.10

MIT

SU

BIS

HI


F4A33/W4A32/W4A33 FWD 4 Spd

D

C

E

B

A

42

311 310 211*228*

046070 034 510530

313036

520

179


500

336337046555

Direct Drum

965 975 879

565

231881 022334 335 964 974 877 858 106 128 148 878*

Forward Clutch

232 574 234 251 622

Forward Hub Shell / Kickdown

Drum KickdownBand

052614

182 052

Rev. Sun Gear

Forward Sun Gear

241242

056 612 056247

989 584 594

Rear Planet

583

781692 219

896

909

896907B

907

906

905Servo

758 303

760

757 374

Ring Gear

347

342

740

V.B.Parts

741

654

Low / Rev Sprag

889251252 060

604 268 710894

271

494

Drive

Case

436

437

765

010

995

Park Pawl

991

Linkage 779994

992

349326

493

F

564

895605 078

774

848369

420

360

366194

195

300

7.11

MITS

UB

ISH

I


D

C

E

B

A

230229

554

Forward Drum

177 358670

Input Shaft

106 126 146 878*

Direct Clutch

885* 630

386

044

Center Support

339 338 967 857 977 893 155 114 134 154


567

041 675 570220 861* 140 100

O.Dr. Hub

120

O.Dr. Clutch

862863

970 960

560

330 331550 083

223

O.Dr. Drum

304 762

O.Dr. Cover

730 281 280 735

Pinion

273 274

42

725

181

214 185780

F4A33

076

Diff.Parts

717

076 288 289

716 720 292 291

Differential

715

726

F

126

787375275*

348793

794

FWD 4 Spd

786

W4A32 / W4A33

677730

Pinion

273276*

734 719 290* 728297

718 712 280 735

Differential

274 274375

275*281296273

787

284 283 714 283 679

Idler

282 282290*

F4A33/W4A32/W4A33

7.3b

MIT

SU

BIS

HI


PART # PAPER & RUBBER KIT QTY. REFERENCE #

42000A ...........Paper & Rubber Kit, KM170/KM17/KM172 1979-88 .......................................................................1 ......................42000C ...........Paper & Rubber Kit, KM175/KM177 1985-88 .................................................................................1 ......................42000E ...........Paper & Rubber Kit, KM175-5/KM176-5/KM177-8 1988-Up ...........................................................1 ......................42000H ...........Paper & Rubber Kit, KM171-5/KM172-5 1989-Up ..........................................................................1 ......................42000L ............Paper & Rubber Kit, A4AF1 1991-Up ..............................................................................................1 ......................42000LB .........Paper & Rubber Kit, A4AF2 / A4BF1 (Elantra 1996-99) (Tiburon 1997-99) ....................................1 ......................42000LC .........Paper & Rubber Kit, A4AF3/A4BF2/A4BF3 (Elantra 2000)(Tiburon 2000-01)(Accent 2000-03) ....1 ......................42000M...........Paper & Rubber Kit, F4A33-1 1990-Up / W4A32/W4A33 (Without Transfer Case........................Parts) 1990-Up ................................................................................................................................1 ......................42000MA ........Paper & Rubber Kit, W4A32/W4A33 (With Transfer Case Parts) 1990-Up ....................................1 ......................

PART # OVERHAUL KITS QTY. REFERENCE #

42002A ...........Overhaul Kit, KM170/KM171/KM172 1979-88 ................................................................................1 ......................42002C ...........Overhaul Kit, KM175/KM177 1985-88 ............................................................................................1 ......................42002E ...........Overhaul Kit, KM175-5/KM176-5/KM177-8 1988-Up ......................................................................1 ......................42002H ...........Overhaul Kit, KM171-5/KM172-5 1989-Up .....................................................................................1 ......................42002L ............Overhaul Kit, A4AF1/A4AF2 1991-Up (A4AF2 Accent 1995-9/99) .................................................1 ......................42002LB .........Overhaul Kit, A4AF2 / A4BF1 (Elantra 1996-99) (Tiburon 1997-99) ...............................................1 ......................42002LC .........Overhaul Kit, A4AF3/A4BF2/A4BF3 (Elantra 2000) (Accent 2000-03) (Tuburon 2000-01) ............1 ......................42002M...........Overhaul Kit, F4A33-1 1990-Up / W4A32/W4A33 (Without Transfer Case Parts) 1990-Up ...........1 ......................42002MA ........Overhaul Kit, W4A32/W4A33 (With Transfer Case Parts) 1990-Up ...............................................1 ......................

PART # MASTER L/STEEL KIT QTY. REFERENCE #

42004A ...........Master L/Steels Kit, KM170/KM171/KM172 1979-88 ......................................................................1 ......................42004C ...........Master L/Steels Kit, KM175/KM177 1985-88 ..................................................................................1 ......................42004E ...........Master L/Steels Kit, KM175-5/KM176-5/KM177-8 1988-Up ...........................................................1 ......................42004H ...........Master L/Steels Kit, KM171-5/KM172-5 1989-Up ...........................................................................1 ......................42004L ............Master L/Steels Kit, A4AF1 1991-Up (Also A4AF2 Accent 1995-9/1999) .......................................1 ......................42004LB .........Master L/Steels Kit, A4AF2 / A4BF1 (Elantra 1996-99) (Tiburon 1997-99) .....................................1 ......................42004LD .........Master L/Steels Kit, A4AF3/A4BF2/A4BF3 2000-Up ......................................................................1 ......................42004LC .........Master L/Steels Kit, A4AF3/A4BF2/A4BF3 (Elantra 2000)(Tiburon 2000-01) .................................1 ......................42004LD .........Master L/Steels Kit, A4AF3 (Accent) 2000-Up ................................................................................1 ......................42004M...........Master L/Steels Kit, F4A33-1/W4A33 (Without Transfer Case Parts) 1990-Up ..............................1 ......................42004MA ........Master L/Steels Kit, W4A33 (With Transfer Case Parts) 1990-Up ..................................................1 ......................42004NA .........Master L/Steels Kit, W4A32 (With Transfer Case Parts) 1990-Up ..................................................1 ......................

PART # MASTER W/STEEL KIT QTY. REFERENCE #

42006A ...........Master W/Steels Kit, KM170/KM171/KM172 1979-88 ....................................................................1 ......................42006C ...........Master W/Steels Kit, KM175 1985-88 .............................................................................................1 ......................42006E ...........Master W/Steels Kit, KM175-5/KM177-8 1988-Up ..........................................................................1 ......................42006H ...........Master W/Steels Kit, KM171-5/KM172-5 1989-Up ..........................................................................1 ......................42006J ............Master W/Steels Kit, KM176-5 1989-Up .........................................................................................1 ......................42006L ............Master W/Steels Kit, A4AF1 1991-Up (Also A4AF2 Accent 1995-9/1999) ......................................1 ......................42006LB .........Master W/Steels Kit, A4AF2/A4BF1 (Elantra 1996-99) (Tiburon 1997-99) .....................................1 ......................42006LC .........Master W/Steels Kit, A4AF3/A4BF2/A4BF3 (Elantra 6/1999-6/2000) (Accent 9/1999-2003)........................(Tiburon 6/1999-9/2001) ..................................................................................................................1 ......................42006LD .........Master W/Steels Kit, A4AF3 (Accent) 2000-Up ...............................................................................1 ......................42006M...........Master W/Steels Kit, F4A33-1/ W4A33 (Without Transfer Case Parts) 1990-Up ............................1 ......................42006MA ........Master W/Steels Kit, W4A33 (With Transfer Case Parts) 1990-Up ................................................1 ......................42006NA .........Master W/Steels Kit, W4A32 (With Transfer Case Parts) 1990-Up ................................................1 ......................42006P ...........Master W/Steels Kit, KM177 1985-88 .............................................................................................1 ......................

KM170 thru W4A33 FWD 3 & 4 Speed

7.3c

MITS

UB

ISH

I


PART # FILTER QTY. REFERENCE #

42010A ...........Filter, KM170 (Felt) 1979-81 ...........................................................................................................1 ......................MD70778642010AA .........Filter, KM170/KM171/KM172/KM175 (Felt) 1982-87 ......................................................................1 ......................MD71005642010E ...........Filter, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8 (.700”) 1987-Up (Half Plastic) ..................1 ......................MD73-784042010EA .........Filter, KM171-5/KM172-5/KM175-5/KM177-8 (Felt) 1987-Up .........................................................1 ......................MD72-995542010L ............Filter, A4AF1/ A4BF1 / A4BF2 (Half Plastic) 1991-Up .....................................................................1 ......................42010LA .........Filter, A4AF3/A4BF3 (Hyundai) (Half Plastic) 2000-Up ...................................................................1 ......................4210M.............Filter, F4A3/W4A32/W4A33 (ero Leak) (HalfPlastic) 1990-Up ........................................................1 ......................M73-557242010P ...........Filter, KM175-5KM177-8 (Felt) (loks Like A Boot) 1987-Up ............................................................1 ......................

42010A 42010AA 42010E 42010EA

42010L 42010LA 42010M

PART # FILTER KIT QTY. REFERENCE #

42011A ............Filter Kit, KM170 (Felt) 1979-81 ......................................................................................................1 ......................42011AA .........Filter Kit, KM170/KM171/KM172/KM175 (Felt) 1982-87 ................................................................1 ......................42011E ...........Filter Kit, KM171-5/KM172-5/KM175-5/KM176-5 (Zero Leak) (.700”) 1987-Up ..............................1 ......................42011EA .........Filter Kit, KM171-5/KM172-5/KM175-5/KM176-5 (Felt) 1987-Up ...................................................1 ......................42011L ............Filter Kit, A4AF1/A4BF1/A4BF2 1991-Up (Half Plastic) ..................................................................1 ......................42011LA ..........Filter Kit, A4BF-3 (Hyundai) 2000-Up ..............................................................................................1 ......................42011M ...........Filter Kit, F4A33-1/W4A32-1/W4A33-1 (Zero Leak) 1990-Up .........................................................1 ......................42011P ...........Filter Kit, KM177 1987-Up ...............................................................................................................1 ......................

PART # BANDS QTY. REFERENCE #

42022A ...........Band, KM170/KM171/KM172/KM175/KM171-5/KM172-5/KM175-5/KM176-5/A4AF1/A4AF3........................(1 9/16” Wide) .................................................................................................................................1 ......................MD72528742022G ...........Band, KM177/KM177-8/A4BF1/A4BF2/W4A32 (1 3/4” Wide) 1987-Up .........................................1 ......................MD72140842022M...........Band, F4A33/W4A33 Kickdown (2 3/8” Wide) 1990-Up .................................................................1 ......................MD736920

PART # BUSHINGS QTY. REFERENCE #

42030AC.........Bushing Kit, KM170/KM171/KM172/KM171-5/KM172-5 1979-Up ..................................................1 ......................42030DC ........Bushing Kit, KM172/KM175 1983-88 ..............................................................................................1 ......................42030E ...........Bushing Kit, KM171-5/KM175-5/KM176-5/KM177-8/A4AF/A4BF 1989-Up ....................................1 ......................42030M...........Bushing Kit, F4A33 .........................................................................................................................1 ......................42034A ...........Bushing, All KM Pump Body 1979-Up .............................................................................................1 ......................42036A ...........Bushing, All KM Stator Support (Front)(.945”OD) 1979-88 .............................................................1 ......................42036E ...........Bushing, All KM Stator Support (Front)(.988”OD) 1989-Up ............................................................1 ......................42041C ...........Bushing, KM175/KM177 Overdrive Shaft (.732”ID) 1985-88 (Use 42056C) ...................................1 ......................42041E ...........Bushing, KM175-5/KM176-5/KM177-8/A4AF-1/W4A32/W4A33 Overdrive Shaft (.808”ID) ........................(Use 42056E) ..................................................................................................................................1 ......................42044A ...........Bushing, KM170/KM171 Center Support (Wide) (1.537”ID) 1979-88 .............................................1 ......................010-323-11542044C ...........Bushing, KM172/KM175/KM177 Center Support (Front) (Narrow) (1.653”ID) 1983-88 .................1 ......................42044CR ........Bushing, KM172/KM175/KM177 Center Support (Rear ) (Narrow) (1.576”ID) 1983-88 .................1 ......................

FWD 3 & 4 Speed KM170 thru W4A33

7.3d

MIT

SU

BIS

HI


PART # BUSHINGS (Continued) QTY. REFERENCE #

42044E ...........Bushing, All KM With Steel Center Support (Narrow) 1.690”ID 1988-Up ........................................1 ......................42046A ...........Bushing, KM170/KM171/KM172/KM175/KM171-5/KM176-5/A4AF1/A4BF2 Direct Drum (Wide)........................(2.047”ID) 1979-Up .........................................................................................................................1 ......................MD70728342046E ...........Bushing, KM172-5/KM175-5/KM177-8/A4BF1/F4A33/W4A32/W4A33 Direct Drum ........................(Front) Narrow (2.157”ID) 1989-Up .................................................................................................1 ......................42046ER.........Bushing, KM172-5/KM175-5/KM177-8/A4BF1/F4A33/W4A32/W4A33 Direct Drum ........................(Rear) Narrow (2.047”ID) 1989-Up .................................................................................................1 ......................42046L ............Bushing, A4AF3 Direct Drum (Front) (2.054”ID) Fits The 42555L Drum (These Are Special........................Made For Us) ..................................................................................................................................1 ......................42052A ...........Bushing, KM170/KM171 Reverse Sun Gear (.823”ID) 1979-88 .....................................................2 ......................MD70746342052C ...........Bushing, KM175/KM177 Reverse Sun Gear (1.023”ID) 1985-88 ...................................................2 ......................42052D ...........Bushing, KM172/KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/........................F4A33/W4A32/W4A33 Reverse Sun Gear (1.102”) ........................................................................2 ......................MD72076042056C ...........Bushing, KM175/KM177 Forward Sun Gear (.732”ID) 1985-88 (Also Fits KM175/KM177 ........................Overdrive Shaft #041) ................................................................................................................... 2-3 .....................MD71276642056E ...........Bushing, KM175-5/KM176-5/KM177-8/A4AF/A4BF/F4A33/W4A32/W4A33 Forward Sun Gear ........................(.808”ID) 1988-Up (Also Fits KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/........................W4A32/W4A33 Overdrive Shaft #041) ......................................................................................... 2-3 .....................MD720769 42058A ...........Bushing, KM170/KM171/KM172/KM171-5/KM172-5 Planet (.469”ID) 1979-Up .............................1 ......................MD71528642060A ...........Bushing, KM170/KM171 Output Shaft (.904”ID) 1979-88 ...............................................................1 ......................MD707454B42060C ...........Bushing, KM172/KM175/KM177 Output Shaft (Front) (1.178”ID) 1983-88 .....................................1 ......................MD73348642060CR ........Bushing, KM172/KM175/KM177 Output Shaft (Rear) (1.018”ID) 1985-88 .....................................1 ......................42060E ...........Bushing, KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/F4A33/W4A32/W4A33 ........................Output Shaft (Front) (1.300”ID) 1988-Up ........................................................................................1 ......................42060H ...........Bushing, KM171-5 Output Shaft (.924”ID) 1989-Up .......................................................................1 ......................

PART # METAL CLAD SEALS QTY. REFERENCE #

42070A ...........Seal, All KM Series (Front) 1979-Up ...............................................................................................1 ......................MD95560142076A ...........Seal, All KM (Both Sides) 1979-Up (Except F4A33 6/1992-Up) (.395” Thick) ................................2 ......................MD70718442076M...........Seal, F4A33 (Both Axles) 6/1992-Up ..............................................................................................1 ......................42083E ..........Seal, KM175-5/KM176-5/KM177-8/A4AF3/A4BF1/A4BF2/F4A33/W4A32/W4A33 Overdrive ........................Drum 1988-Up (11/16”ID) 1988-Up .................................................................................................1 ......................MD72253142083EA .........Seal, KM175-5/KM176-5/KM177-8/A4AF1/W4A32 Overdrive Drum (1/2”ID) 1992-Up ..................1 ......................MD736847

PART # FRICTION CLUTCH QTY. REFERENCE #

42100C ...........Friction, KM175/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/F4A33/W4A32/W4A33........................Overdrive Clutch (.074”) (40 Teeth) 1985-Up ................................................................................ 3-4 .....................MD739092A42100CAPPK .Friction & Steel Kit, All KM Series Overdrive Clutch (Contains; 4 Red .059” Frictions, ........................& 4 Kolene .047” Steels) (Alto) ........................................................................................................1 ......................5975742100L ............Friction, A4AF3 Overdrive Clutch (.065”) (36 Teeth) 2000-Up ...................................................... 3-4 .....................42106A ...........Friction, KM171/KM172 Forward Clutch (.075”) (10 Teeth) 1982-88 ............................................ 2-3 .....................MD71434542106B ...........Friction, KM170/KM171/KM172/KM175/KM177 Forward & Direct Clutch (.075”) (38 Teeth)........................(5.000”OD) 1979-88 ...................................................................................................................... 4-6 .....................MD71365542106E ...........Friction, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/W4A32 ........................Forward & Direct Clutch (.075”) (38 Teeth) (4.996”OD) 1989-Up ................................................. 4-6 .....................MD72255542106L ............Friction, A4AF3/A4BF2/A4BF3 Forward Clutch (.066”) 38 Teeth (Eclipse) 2000-Up .................... 4-6 .....................42106M...........Friction, F4A33/W4A33 Direct Clutch (.067”) (38 Teeth) (5 7/16”OD) 1990-Up ..............................4 ......................MD73582842106MC ........Friction, F4A33/W4A33 Forward Clutch (.067”) (42 Teeth) (5 7/16”OD) 1990-Up ..........................5 ......................MD73158242114B ...........Friction, KM170/KM171/KM172/KM175 Low/Reverse Clutch (.072”) (48 Teeth) 1979-88 ............ 4-6 .....................MD72810842114E ...........Friction, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/W4A32 ........................Low/Reverse Clutch (.071”) (51 Teeth) 1987-Up ............................................................................6 ......................MD71983342114L ............Friction, A4AF1/A4BF2/A4BF3 Low/Reverse Clutch (.071”) 51 Teeth (Eclipse) 2000-Up ............ 5-6 .....................42114M ...........Friction, F4A33/W4A33 Low/Reverse Clutch (.067”) (54 Teeth) (6 1/4”OD) 1990-Up .................. 5-6 .....................MD73158642119E ...........Friction Module, KM175-5/KM176-5/KM177-8/A4AF1/A4AF2/A4BF1/W4A32 1988-Up ................1 ......................42119H ...........Friction Module, KM171-5/KM172-5 1988-Up .................................................................................1 ......................42119LD .........Friction Module, A4AF3/A4BF2/A4BF3 2000-Up ............................................................................1 ......................42119M ...........Friction Module, F4A33/W4A33 1990-Up .......................................................................................1 ......................

PART # STEEL CLUTCH QTY. REFERENCE #

42120C ...........Steel, KM175/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/F4A33/W4A32/W4A33........................Overdrive Clutch (.032”) (25 Teeth) 1985-Up ................................................................................ 3-4 .....................MD71252842120L ............Steel, A4AF3 Overdrive Clutch (.097”) 25 Teeth (3.770”ID) 1993-Up ........................................... 3-4 .....................42120LD .........Steel, A4BF Overdrive Clutch (.160”) 25 Teeth (3.770”ID) 2000-Up ............................................. 3-4 .....................


7.3e

MITS

UB

ISH

I


42126B ...........Steel, KM170/KM171/KM172/KM175/KM177 Direct Clutch (.150”) (24 Teeth) (3.970”ID) ........................1979-88 (This Is Also The Pressure Plate 42146B) ...................................................................... 3-4 .....................MD70725642126E ...........Steel, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/W4A32 .......................Direct Clutch (.146”) (24 Teeth) (4.117”ID) 1989-Up (This Is Also The Pressure Plate 42146E) .. 2-3 .....................MD72255942126G ...........Steel, F4A33 Direct Clutch (.120”) (24 Teeth) (4.117”ID) 1992-Up) .............................................. 2-3 .....................MD73950942126M...........Steel, F4A33/W4A33 Direct Clutch (.088”) (26 Teeth) (4.115”ID) 1990-Up .....................................3 ......................MD73938442126MB ........Steel, F4A33/W4A33 Direct Clutch (.150”) (26 Teeth) (4.115”ID) 1990-Up .....................................1 ......................42128A ...........Steel, KM170/KM171/KM172/KM175/KM177 Forward Clutch (.071”) (24 Teeth) ........................(3.970”ID) 1979-88 ..........................................................................................................................2 ......................MD70725542128E ...........Steel, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/W4A32 Forward ........................Clutch (.071”) (24 Teeth) (4.100”ID) 1989-Up ............................................................................... 2-3 .....................MD72255642128L ............Steel, A4AF3 Forward Clutch (.077”) 24 Teeth (4.100”ID) 1993-Up ........................................................................42128LA .........Steel, A4AF1/A4AF2/A4BF1 Forward Clutch (.087”)(24 Teeth)(4.100”ID) 1999-Up .......................1 ......................42128M...........Steel, F4A33/W4A33 Forward Clutch (.071”) (26 Teeth) (4.360”ID) 1990-Up ................................5 ......................MD73160442134A ...........Steel, KM170 Low/Reverse Clutch (.071”) (6 Teeth) (5.00”ID) 1979-81 .........................................3 ......................MD70740142134B ...........Steel, KM171 Low/Reverse Clutch (.071”) (12 Teeth) (5.00”ID) 1982-84 .......................................3 ......................MD70742542134BB .........Steel, KM172/KM175/KM177 Low/Reverse Clutch (.039”) (24 Teeth) (5.00”ID) 1984-88 ..............5 ......................MD70494842134BC.........Steel, KM171/KM172/KM175 Low/Reverse Clutch (.071”) (24 Teeth) (5.00”ID) 1985-88 ..............3 ......................MD71543842134E ...........Steel, KM172-5/KM175-5/KM176-5/KM177-8/A4AF3 Low/Reverse Clutch (.039”) ........................(20 Teeth) (5.300”ID) 1987-Up ........................................................................................................5 ......................MD72779842134H ...........Steel, KM171-5/KM176-5/A4AF1/A4BF1/A4BF2/W4A32 Low/Reverse Clutch (.071”) ........................(20 Teeth)(5.300”ID) 1989-Up .........................................................................................................3 ......................MD72779942134M...........Steel, F4A33/W4A33 Low/Reverse Clutch (.039”) (20 Teeth) (5.540”ID) 1990-Up ....................... 4-5 .....................MD73158742134P ...........Steel, KM177 Low/Reverse Clutch (.039”) (24 Teeth) (5.300”ID) 1987-88 .....................................5 ......................MD71983442139E ...........Steel Module, KM175-5/177-8 1988-Up ..........................................................................................1 ......................42139H ...........Steel Module, KM171-5/172-5 1988-Up ..........................................................................................1 ......................42139M...........Steel Module, F4A33/W4A33 1990-Up ...........................................................................................1 ......................

PART # CLUTCH PRESSURE PLATES QTY. REFERENCE #

42140C ...........Pressure Plate, P.Plate, KM175/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/F4A33/........................W4A32/W4A33 Overdrive Clutch (25 Teeth) .177” (4.170”ID) 1985-Up .........................................1 ......................42140L ............Pressure Plate, A4AF3 Overdrive Clutch (25 Teeth) .177” (3.770”ID) 1993-Up ..............................1 ......................42146B ...........Steel, Km170/KM171/KM172/KM175/KM177 Direct Clutch (.150”) (24 Teeth) (3.970”ID) 1979-88........................(Use 42126B) ..................................................................................................................................1 ......................MD72715742146E ...........Pressure Plate, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF/W4A32 Forward ........................& Direct Clutch (.146”) (24 Teeth) (4.117”ID) 1989-Up (Use 42126E) .............................................1 ...................... 42146EA .........Pressure Plate, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/W4A32 ........................Forward & Direct Clutch (.192”) (24 Teeth) (4.100”ID) 1989-Up .....................................................1 ...................... 42146L ............Pressure Plate, A4AF3 Forward Clutch (.246”)(24 Teeth)(4.215”ID) .............................................1 ......................42146M...........Pressure Plate, F4A33/W4A33 Direct Clutch (.195”) (26 Teeth) (4.120”ID) 1990-Up .....................1 ......................42148M...........Pressure Plate, F4A33/W4A33 Forward Clutch (.240”) (26 Teeth) (Stepped) 1990-Up .................1 ......................42149B ...........Apply Plate, KM170/KM171/KM172/KM175/KM177 Forward Clutch (Bottom) (.195”) ........................(24 Teeth) (4.00”ID) (Beveled) 1979-88 ..........................................................................................1 ......................MD70725142149E ...........Pressure Plate, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/W4A32 ........................Forward Beveled (24 Teeth) .195” (4.100”ID) Bottom 1989-Up ......................................................1 ......................MD73240842149M...........Pressure Plate, F4A33/W4A33 Forward Clutch (26 Teeth) .160” (Stepped) Bottom 1990-Up .......1 ......................42154A ...........Pressure Plate, KM170 Low/Reverse Clutch (.150”) (6 Teeth) (5.00”ID) 1979-81 ..........................1 ......................42154B ...........Pressure Plate, KM171/KM172/KM175 Low/Reverse Clutch (.145”) (12 Teeth) ........................(5.00”ID) 1982-88 ............................................................................................................................1 ......................42154E ...........Pressure Plate, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/........................W4A32 Low/Reverse Clutch (.145”) (20 Teeth) (5.300”ID) 1989-Up ..............................................1 ......................42154G ...........Pressure Plate, KM177-8 Low/REverse Clutch (20 Teeth) .100” Thick (5.300”ID) 1989-Up...........1 ......................42154M...........Pressure Plate, F4A33/W4A33 Low/Reverse Clutch (.160”) (20 Teeth) (5.540”ID) 1990-Up .........1 ......................42154P ...........Pressure Plate, KM177 Low/Reverse Clutch (.166”) (20 Teeth) (5.540”ID) 1988 ...........................1 ......................42155A ...........Apply Plate, KM170 Low/Reverse Clutch (.150”) (6 Teeth) (5.00”ID) 1979-83 ...............................1 ......................42155B ...........Apply Plate, KM171/KM172/KM175 Low/Reverse Clutch (.220”) (12 Teeth) (5.00”ID)........................ (Beveled) 1982-88 ..........................................................................................................................1 ......................MD70740242155E ...........Apply Plate, KM171-5/KM172-5/KM175-5/KM176-5/A4AF1/A4AF3/A4BF1/A4BF2/W4A32........................Low/Reverse Clutch (.245”) (20 Teeth) (5.300”ID) (Beveled) 1989-Up ...........................................1 ......................42155EA .........Apply Plate, KM171-5/KM172-5/KM175-5/KM176-5/A4AF1/A4AF3/A4BF1/A4BF2/W4A32........................Low/Reverse Clutch (.155”) (20 Teeth) (5.300”ID) (Beveled) 1989-Up ...........................................1 ......................42155M...........Apply Plate, F4A33/W4A33 Low/Reverse Clutch (.255”) (20 Teeth) (5.540”ID) (Beveled) ........................1990-Up ..........................................................................................................................................1 ......................


7.3f

MIT

SU

BIS

HI


PART # VALVE BODY KITS QTY. REFERENCE #

T42165C .........Shift Kit, KM175/KM177/KM175-5/KM176-5/KM177-5 (4 Speed) 1988-Up (Mitsubishi, ........................Hyundai, Dodge) Prevents/Reduces 2-3 Cutloose, Long/Soft 3rd, 3-4 Nuetral, 4-2 Kickdown........................Runaway .........................................................................................................................................1 ......................SK® KM-175/77A42165L .........Valve Body Kit, A4AF/A4BF With 6 Solenoids (Translab) ...............................................................1 ......................

PART # OIL SEALING RINGS QTY. REFERENCE #

42175A ...........Ring Kit, KM170/KM171/KM172 1979-88 .......................................................................................1 ......................42175C ...........Ring Kit, KM175/KM177 1985-88 ....................................................................................................1 ......................42175CC ........Ring Kit, All KM Series 4 Speed (Except F4A33/W4A33) Combo 1985-Up ....................................1 ......................42175E ...........Ring Kit, KM175-5/KM176-5/KM177-8/A4AF/W4A32 1989-Up ......................................................1 ......................42175H ...........Ring Kit, KM171-5/KM172-5 1989-Up .............................................................................................1 ......................42175M...........Ring Kit, F4A33/W4A33 1990-Up ...................................................................................................1 ......................42177A ...........Ring, KM170/KM171/KM172/KM175 Input Shaft (Front) Small .944”OD (Metal) 1979-88 ........... 1-3 .....................MD70723642177ET .........Ring, KM171-5/KM172-5/KM176-5/KM177/KM177-8/A4AF/F4A32/W4A32/W4A33 Input ........................Shaft (Front) Small 1.023”OD (Teflon) 1983-Up ..............................................................................3 ......................MD72255142179A ...........Ring, All KM Series Pump Stator 2.165”OD (Metal) 1979-Up .........................................................2 ......................MD70764642179ET .........Ring, All KM Series Pump Stator 2.165”OD (Teflon) 1988-Up ........................................................2 ......................MD71399142181A ...........Ring, KM170/KM171/KM172/KM175 Forward Drum (Front) 1.259”OD (Metal) 1979-88 ...............1 ......................MD70723542181AT .........Ring, KM170/KM171/KM172/KM175 Forward Drum (Front) 1.259”OD (Teflon) 1979-88 ...............1 ......................42181E ...........Ring, KM171-5/KM172-5/KM175-5/KM176-5/KM177/KM177-8/A4AF/F4A33/W4A32/W4A33 ........................Forward Drum (Front) 1.370”OD (Metal) 1988-Up ..........................................................................1 ......................MD72263942182ET .........Ring, KM175-5/KM172-5/KM175-5/KM176-5/KM177-5/F4A32/F4A33/W4A32/W4A33 Reverse........................Sun Gear 1.574”OD (Teflon) 1989-Up ............................................................................................1 ......................MD72227842185AT .........Ring, All KM 3 Speed Series Input Shaft (Rear) .513”OD (Teflon) 1979-Up ...................................1 ......................MD70723742185C ...........Ring, All KM 4 Speed Series Overdrive Drum (Lock Joint) (Metal) 1985-Up ..................................1 ......................42189A ...........Ring, KM170/KM171/KM172/KM175/KM171-5/KM172-5 Governor 1.389”OD (Metal) 1979-Up ...3 ......................MD71502042191A ...........Ring, Accumulator Piston (Inner) .882”OD (Metal) ..........................................................................1 ......................MD70720442192A ...........Ring, All KM Series Accumulator Piston (Outer) 1.772”OD (Metal) ................................................1 ......................MD70720242194BT .........Ring, Servo Piston (Small) 1.785”OD (Teflon) ................................................................................1 ......................MD70736942194DT .........Ring, Servo Piston (Small) 1.947”OD (Teflon) ................................................................................1 ......................MD71504742195BT .........Ring, Servo Piston (Large) 2.800”OD (Teflon) ................................................................................1 ......................42195ET .........Ring, Servo Piston (Large) 2.840”OD (Teflon) ................................................................................1 ......................42195MT ........Ring, Servo Piston (Large) 3.700”OD (Teflon) ................................................................................1 ......................42195PT .........Ring, Servo Piston (Large) 3.000”OD (Teflon) ................................................................................1 ......................

PART # WASHERS & BEARINGS QTY. REFERENCE #

42211B ...........Washer, All KM Series Stator To Direct Drum (.055”) Fiber (Also Fits Forward Drum To ........................Direct Drum) .................................................................................................................................. 1-2 .....................42211BA .........Washer, All KM Series Stator To Direct Drum (.070”) Fiber ............................................................1 ......................42211BB .........Washer, All KM Series Stator To Direct Drum (.086”) Fiber ............................................................1 ......................42211BC .........Washer, All KM Series Stator To Direct Drum (.100”) Fiber ............................................................1 ......................42211BD .........Washer, All KM Series Stator To Direct Drum (.118”) Fiber .............................................................1 ......................S42211K .........Washer & Shim Kit, All Km Series Stator To Drums (Sonnax) ........................................................1 ......................42214C ...........Washer, KM175 Hub To Overdrive Drum (4 Tab) (1.415”OD) .........................................................1 ......................42214E ...........Washer, KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/W4A32 Hub To Overdrive Drum ........................(4 Tab) (1.490”OD) ..........................................................................................................................1 ......................MD-73410142214L ............Washer, A4AF3 Hub To Overdrive Drum (.079” Thick) No Tabs (1.008”ID) (1.415”OD) .................1 ......................42214M...........Washer, F4A33/W4A33 Hub To Overdrive Drum (4 Tab) (1.500”OD) .............................................1 ......................42220C ...........Washer, KM175 Overdrive Hub Front With (1 Tab) (.072”) .............................................................1 ......................MD71587742220E ...........Bearing With Race, KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/W4A32/W4A33 Overdrive ........................Hub (Front) ......................................................................................................................................1 ......................42220L ............Bearing W/Race & Cup Race, A4BF1/A4BF2 Overdrive Hub (Front) .109” Thick (1.669”OD) ........................1.108”ID (Cup Race Has 6 Flat Sides) 2 Piece Set (Sell A 42220LK Per ATRA) ............................1 ......................42220LA .........Shim, A4BF1/A4BF2 Overdrive Hub (Front) (.015” Thick)(Use With 42220L Bearing To Correct........................Inplay, Per ATRA)(Sell 42220LK Per Atra) ......................................................................................1 ......................42220LK .........Kit, A4BF1A4BF2 Overdrive Hub (Front) Contains: 42220L, 42220LA & 42056E ..........................1 ......................42220P ...........Bearing W/Race, KM177 Overdrive Hub (Front) .............................................................................1 ......................42223C ...........Ball Bearing, KM175-KM177 Overdrive Drum To Overdrive Cover (1.118”OD) ........................(11/16”ID) 1985-88 ..........................................................................................................................1 ......................42223E ...........Ball Bearing, KM175-8/KM176-5/KM177-8/A4AF1/F4A33/W4A32/W4A33 Overdrive Drum To ........................Overdrive Cover (1.122”OD) (1/2”ID) 1989-95 ................................................................................1 ......................42223L ............Ball Bearing, A4AF3/A4BF1/A4BF2 Overdrive Drum To Overdrive Cover (1.181”OD) (.671”ID) ...1 ......................42228B ...........Race, All KM Series Forward Drum To Stator (.030”)......................................................................1 ......................42228BA .........Race, All KM Series Forward Drum To Stator (.046”)......................................................................1 ......................42228BAA.......Race, All KM Series Forward Drum To Stator (.055”)......................................................................1 ......................42228BB .........Race, All KM Series Forward Drum To Stator (.062”)......................................................................1 ......................


7.3g

MITS

UB

ISH

I


42228BBB ......Race, All KM Series Forward Drum To Stator (.070”)......................................................................1 ......................42228BC.........Race, All KM Series Forward Drum To Stator (.078”)......................................................................1 ......................42229B ...........Bearing With Race, All KM Series Forward Drum To Stator............................................................1 ......................42230B ...........Washer, All KM Series Forward Drum To Direct Drum (2 3/4”OD) (.055”) (Use 42211B) ...............1 ......................42230M...........Washer, F4A33/W4A33 Forward Drum To Direct Drum (2 9/16”OD) ..............................................1 ......................42231B ...........Race, KM170/KM171 Forward Drum To Hub (1 3/8”OD) ................................................................1 ......................42231C ...........Race, KM172/KM175 Forward Drum To Hub (1 9/16”OD) (3/4”ID).................................................1 ......................42231E ...........Race, KM171-5/KM172-5/KM176-5/A4AF1/A4AF3/A4BF1/A4BF2/F4A33/W4A32/W4A33 ........................Forward Drum To Hub (1 9/16”OD) (13/16”ID) ................................................................................1 ......................42232B ...........Bearing W/Race, KM170/KM171 Forward Drum To Hub ................................................................1 ......................42232C ...........Bearing W/Race, KM172/KM175 Forward Drum To Hub ................................................................1 ......................42232E ...........Bearing W/Race, KM171-5/KM172-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/F4A33/........................W4A32/W4A33 Forward Drum To Hub ...........................................................................................1 ......................42234B ...........Race, All KM Series Forward Hub To Kickdown Drum (.060”) ........................................................1 ......................42234C ...........Race, All KM Series Forward Hub To Kickdown Drum (.030”) ........................................................1 ......................42234M...........Race, All KM Series Forward Hub To Kickdown Drum (.063”) ........................................................1 ......................42241B ...........Bearing, KM170/KM171 Reverse Sun Gear To Forward Sun Gear (.880”ID) .................................1 ...................... 42241C ...........Bearing, KM170/KM171 Reverse Sun Gear To Forward Sun Gear (1.030”ID) ...............................1 ......................42241E ...........Bearing, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/W4A32 ........................Reverse Sun GearTo Forward Sun Gear (1.208”ID) .......................................................................1 ......................42241M...........Race, F4A33/W4A33 Reverse Sun Gear To Forward Sun Gear (1.225”ID) ...................................1 ...................... 42242C ...........Race, KM172/KM175 Reverse Sun Gear To Forward Sun Gear (1.028”ID) ...................................1 ......................42242E ...........Race, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/W4A32 ........................Reverse Sun Gear To Forward Sun Gear (1.208”ID) ......................................................................1 ...................... 42242M...........Bearing W/Race, F4A33/W4A33 Reverse Sun Gear To Forward Sun Gear ..................................1 ...................... 42247B ...........Bearing, KM170/KM171/KM172/KM175-5/KM176-5/KM177-8/A4AF1/W4A32 Forward Sun Gear ........................To Planet (Stays In Planet) ..............................................................................................................1 ...................... 42247D ...........Bearing, KM172/KM175 (Some) Forward Sun Gear To Planet .......................................................1 ......................42247L ............Bearing W/Races, A4AF3/A4BF1/A4BF2 Forward Sun Gear To Planet (Stays In Planet) .............1 ......................42247M...........Bearing W/Race, F4A33/W4A33 Forward Sun Gear To Planet (Stays In Planet) ..........................1 ......................42248D ...........Race, KM172/KM175 (Some) Forward Sun Gear To Planet ...........................................................1 ......................42251B ...........Bearing W/Race, KM170/KM171 Planet To Output Hub (1.805”OD) (Also Forward Hub To ........................Kickdown Drum) ............................................................................................................................ 1-2 .....................42251C ...........Bearing W/Race, KM172/KM175/KM171-5/KM172-5/KM175-5/KM176-5/A4AF1 Planet To ........................Output Hub (2.045”OD) (Also KM172/KM171-5/KM172-5/KM175-5/KM176-5/A4AF1/A4AF3/........................A4BF1/A4BF2 Forward Hub To Kickdown Drum) ......................................................................... 1-2 ..................... 42251G ...........Bearing W/Race, KM177-8/F4A33/W4A33 Planet To Output Hub (2.128”OD) (Also ........................Forward Hub To Kickdown Drum) ................................................................................................. 1-2 ..................... 42251L ............Bearing W/Races, A4BF3/A4BF1/A4BF2 Planet To Hub (.142” Thick)(2.100”OD) .........................1 ......................42252B ...........Race, KM170/KM171 Planet To Output Hub (1.455”ID) .................................................................1 ......................42252C ...........Race, KM175/KM171-5/KM172-5 Planet To Output Hub (1.528”ID) ...............................................1 ......................42268B ...........Ball Bearing, KM170/KM171/KM171-5 Drive Gear (Front) (1.358”ID) ............................................1 ......................42268C ...........Ball Bearing, KM172/KM175 Drive Gear (Front) 1.575”ID (2.830”OD) ...........................................1 ......................42268E ...........Ball Bearing, KM175-5/KM176-5/KM177-8 Drive Gear (Front) 1.770”ID ........................................1 ......................42268L ............Ball Bearing, A4AF1/F4A33/W4A32/W4A33 Drive Gear (Front) 2.365”ID ......................................1 ......................42268LB .........Double Ball Bearing, A4AF3/A4BF2 Drive Gear (Front)(With 4 Bolt Flange)(2.045”ID)........................(4.109”OD With Flange) ..................................................................................................................1 ......................42268LC .........Ball Bearing, A4AF1 Drive Gear (Front)(2.165”ID) ..........................................................................1 ......................42268Y ...........Ball Bearing, KM172-5 Drive Gear (Front) 1.575”ID (3.145”OD) ....................................................1 ......................42271B ...........Ball Bearing, KM170/KM171/KM171-5 Drive Gear (Rear) 1.175”ID ...............................................1 ......................42271C ...........Ball Bearing, KM172/KM175 Drive Gear (Rear) 1.375”ID ...............................................................1 ......................42271E ...........Ball Bearing, KM175-5/KM176-5/KM177-8 Drive Gear (Rear) 1.572”ID .........................................1 ......................42271L ............Ball Bearing, A4AF1/F4A33/W4A32/W4A33 Drive Gear (Rear) 2.165”ID ......................................1 ......................42271LC .........Ball Bearing, A4AF1/A4AF2 Drive Gear (Rear)(1.930”ID) ..............................................................1 ......................42271Y ...........Ball Bearing, KM172-5 Drive Gear (Rear) 1.575”ID ........................................................................1 ......................42273B ...........Cup Race, KM170/KM171/KM172/KM175/KM171-5/KM172-5 Pinion To Case & Driven ........................Transfer Gear To Case .................................................................................................................. 1-2 .....................42273E ...........Cup Race, KM175-5/KM176-5/KM177-8 Pinion To Case & Driven Transfer Gear To Case ......... 1-2 .....................42273L ............Cup Race, A4AF1/A4AF3/A4BF1/A4BF2 Pinion To Case (2.840”OD) ...........................................1 ......................42273M...........Cup Race, F4A33/W4A32/W4A33 Pinion To Case & Driven Transfer Gear To Case ........................(Cast # 322009J) ........................................................................................................................... 1-2 .....................42273MA ........Cup Race. F4A33 Pinion To Case & Driven Transfer Gear To Case (Cast # 57583-N) ................ 1-2 .....................42274B ...........Cone Bearing, KM170/KM171/KM172/KM175/KM171-5/KM172-5 Pinion & Driven ........................Transfer Gear ................................................................................................................................ 1-2 .....................42274E ...........Cone Bearing, KM175-5/KM176-5/KM177-8/A4AF/F4A33/W4A32/W4A33 Pinion & Driven ........................Transfer Gear ................................................................................................................................ 1-2 .....................42274L ............Cone Bearing, A4AF1/A4AF3/A4BF1/A4BF2 Pinion Shaft (17 Rollers)(1.375”ID) .........................1 ......................42275E ...........Shim, KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2 Pinion Shaft To Driven ........................Transfer Gear (.062”) ......................................................................................................................1 ......................42280L ............Cone Bearing, A4AF3/A4BF1/A4BF2 Transfer Drive Gear (19 Rollers)(1.770”ID) .........................1 ......................


7.3h

MIT

SU

BIS

HI


PART # WASHERS & BEARINGS (Continued) QTY. REFERENCE #

42281L ............Cup Race, A4AF3/A4BF1/A4BF2 Transfer Drive Gear (.627” Thick)(3.350”OD)(2.805”ID) ...........1 ......................42284B ...........Washer, All KM Series (Except F4A33/W4A33) Idler Gear To Case (With 1 Tab) (2.440”OD) .......1 ......................42284M...........Washer, F4A33/W4A33 Idler Gear To Case (With 1 Tab) (1.965”OD) ............................................1 ......................42289LB .........Ball Bearing, A4AF3 Differential Housing (Both Sides)(2.835”OD)(1.377”ID)(.715” Thick)........................(8 Balls) ...........................................................................................................................................2 ......................42290E ...........Shim, KM175-5/KM176-5/KM177-8 Differential Bearing Race To Case (.090”) ..............................1 ......................42290LB .........Shim, A4AF3/A4BF1/A4BF2 Differential Bearing Race To Case (.063”) .........................................1 ......................42291M...........Cup Race, F4A33 Differential Bearing ............................................................................................2 ......................42292LB .........Use 42289LB ..................................................................................................................................1 ......................

PART # GASKETS & RUBBER COMPONENTS QTY. REFERENCE #

42300A ...........Gasket, KM170 Bottom Pan (12 Bolt) 1979-81 ...............................................................................1 ......................42300C ...........Gasket, KM171/KM172/KM175/KM171-5/KM172-5/KM175-5/KM176-5 Bottom Pan (12 Bolt) ......1 ......................42300L ............Gasket, A4AF1/A4AF3 Bottom Pan (13 Bolt) 1991-Up ...................................................................1 ......................42300LF .........Gasket, A4AF1/A4AF3 Bottom Pan (13 Bolt) (Durapreme) 1991-Up .............................................1 ......................42300LA .........Gasket, A4BF1/A4BF2/A4BF3 Bottom Pan (13 Bolt) 1996-Up ......................................................1 ......................42300LAF .......Gasket, A4BF1/A4BF2/A4BF3 Bottom Pan (13 Bolt) 1996-Up (Farpak) .......................................1 ......................42300M...........Gasket, F4A33/W4A32/W4A33 Bottom Pan (14 Bolt) 1990-Up .....................................................1 ......................42300P ...........Gasket, KM177/KM177-8 Bottom Pan (13 Bolt) 1987-Up ...............................................................1 ......................42309A ...........Seal, All KM Series Pump Bolt 1979-Up .........................................................................................6 ......................MD70765342310A ...........Gasket, KM170 Pump 1979-81 .......................................................................................................1 ......................MD70765242310B ...........Gasket, All KM Series (Except F4A33/W4A32/W4A33) Pump 1982-Up .........................................1 ......................MD72238542310L ............Gasket, A4AF1/A4AF2 Pump To Case 1991-Up .............................................................................1 ......................42310M...........Gasket, F4A33/W4A32/W4A33 Pump 1990-Up .............................................................................1 ......................MD75297842311A ............O-Ring, All KM Series Pump 1979-Up ............................................................................................1 ......................MD70763642313E ...........Seal, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF/F4A33 Inner Pump Gear ........................To Converter Hub L1988-Up ...........................................................................................................1 ......................MD72992842318A ...........Gasket, KM170/KM171/KM172 Case To Bell Housing Gasket (14 Hole Cork) 1979-88 ................1 ......................MD70722142318B ...........Gasket, KM171/KM172/KM175 Case To Bell Housing Gasket (18 Hole Cork) 1984-88 ................1 ......................MD70078242318E ...........Gasket, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8 Case To Bell Housing (18 Hole ........................Metal) 1989-Up ...............................................................................................................................1 ......................MD73080442326..............Gasket, All KM Series Filter 1979-81 ..............................................................................................1 ......................42326A ...........Gasket, All KM Series Filter 1982-Up ..............................................................................................1 ......................42330CAK ......Repair Kit, KM175/KM175-5/KM176-5/KM177/KM177-8 Overdrive Clutch (O-Rings) 1987-UP ....1 ...................... 42330CKK ......Repair Kit, KM175/KM175-5/KM176-5/KM177/KM177-8 Overdrive Clutch (O-Rings, ........................Frictions, & Steels) 1985-UP ...........................................................................................................1 ...................... 42330YK .........Repair Kit, F4A33/W4A32/W4A33 Overdrive Clutch (End Clutch) 1991-Up ...................................1 ...................... 42381A ...........O-Ring, All KM Series (With 2 Piece Case) Stator Tube .................................................................1 ......................

PART # TECHNICAL MANUALS QTY. REFERENCE #

42400-1 ..........Those Darn KM’s (Book 1 Identification, Theory And Testing Manual)(ATRA) ...............................1 ......................42400-2 ..........Those Darn KM’s (Book 2 Problems, Fixes & Tips Manual)(ATRA) ................................................1 ......................42400B ...........Technical Manual, KM171/KM172 (3 Speed) ..................................................................................1 ......................83-171TM42400C ...........Technical Manual, KM175 (4 Speed) ..............................................................................................1 ......................83-175TM42400M...........Technical Manual, F4A33/W4A32/W4A33 (4 Speed) 1 Piece Case ...............................................1 ......................42400P ...........Technical Manual, KM177/KM177-8 (4 Speed) With V-6 ................................................................1 ......................83-177TM

PART # ELECTRICAL COMPONENTS QTY. REFERENCE #

42410B ...........Neutral Switch, KM171/KM172 (4 Prong Round Connector) ..........................................................1 ......................42410C ...........Neutral Switch, KM175 (11 Prong Round Connector) .....................................................................1 ......................42410E ...........Neutral Switch, KM171-5/KM175-5/KM176-5 (With Wire Harness)(11 Prong Rectangular ........................Connector) Overall Length Is 10 1/4” ..............................................................................................1 ......................42410EA .........Neutral Switch, KM175-5 (With 7 Prong Connector) Cast # PPS-GF15 .........................................1 ......................42410EB .........Neutral Switch, F4A22/F4A23 (With 11 Prong Oval Connector) Cast # PPS-GF15........................(Connector Points Up) .....................................................................................................................1 ......................42410G ...........Neutral Switch, KM177-8 (With Wire Harness)(With 11 Prong Rectangle Connector) Overall ........................Length Is 17” ...................................................................................................................................1 ......................42410L ............Neutral Switch, A4AF3/A4BF1/A4BF2 (With 11 Prong Oval Connector)(Cast # PA66-0GF15) ......1 ......................42410M...........Neutral Switch, F4A33/W4A33 (With Wire Harness)(With 11 Prong Rectangle Connector) ........................Overall Length Is 13 1/4” .................................................................................................................1 ......................42410MA ........Neutral Switch, F4A33 (With Wire Harness)(With 11 Prong Oval Connector) Overall Length........................Is 13 3/4” ........................................................................................................................................1 ......................42410MB ........Neutral Switch, F4A33 (With 11 Prong Oval Connector) Cast # PPS-GF15 (Connector........................Points Down) ...................................................................................................................................1 ......................42410Y ...........Neutral Switch, KM172-5 (4 Prong Square Connector) ..................................................................1 ......................


7.3i

MITS

UB

ISH

I


42420CK.........Solenoid Kit, KM 4 Speed (4 Solenoid)(With Wire Harness)(All Hyundai 1985-Up........................ & Mitsubishi 1987-92) ....................................................................................................................1 ...................... T42420CK-1 ...Solenoid Master Kit, KM 4 Speed (With Wire Harness) (Teckpak) (All Hyundai 1985-Up &........................Mitsubishi 1987-92) .........................................................................................................................1 ......................42420EK .........Solenoid Kit, All KM 4 Speed (With 4 Solenoids) With 13 OHM Lock-Up Solenoid ........................(For Mitsubishi 1993-Up)(Includes The F4A33)(These Are Flat Nose Solenoids But They Fit........................The Solenoids With Long Snouts) ...................................................................................................1 ...................... T42420EK-1 ...Solenoid Master Kit, KM 4 Speed )4 Solenoid)(With Wire Harness)(For Mitsubishi 1993-Up........................Not For Hyundai)(Teckpak) .............................................................................................................1 ......................42420LD .........Solenoid Assembly, A4AF3 (6 Solenoids With Case Connector) 2000-Up .....................................1 ......................42420MC ........Solenoid Assembly, F4A33 (Diamante, 3000GT, Expo, Gallant) 1990-92 ......................................1 ......................MD73419942420MD ........Solenoid Assembly, F4A33 (Mitsubishi, Eclipse) 1991-92 ..............................................................1 ......................MD-75500942420MG ........Solenoid Assembly, F4A33 (Mitsubishi, Eclpise) 1993-94 ..............................................................1 ......................MD-75500842420MH ........Solenoid Assembly, F4A33 1993-96 ...............................................................................................1 ......................MD-75483242421C ...........Solenoid, KM 4 Speed 1-2 Shift (Orange Wire) 1987-97 ................................................................1 ......................42421CA .........Solenoid, KM 4 Speed 3-4 Shift (Yellow Wire) 1987-97 ..................................................................1 ......................42425E ...........Solenoid, KM Series TCC (Red Wire) 1987-93 ...............................................................................1 ......................42425EA .........Solenoid, KM Series TCC (Lock-Up) (White Wire) 1993-Up ...........................................................1 ......................42425EB .........Solenoid, KM Series EPC (Blue Wire) 1987-97 ..............................................................................1 ......................42431E ...........Solenoid, KM175-5/KM177-5 EPC ..................................................................................................1 ......................42436B ...........Switch, KM171/KM172/KM175 Pulse Generator (Speed Sensors) ................................................1 ......................42436E ...........Switch, KM171-5/KM175-5/KM176-5 Pulse Generators (Speed Sensors) .....................................1 ......................42436G ...........Switch, KM177-8 Pulse Generator (Speed Sensor) ........................................................................1 ......................42436LB .........Switch, A4AF3/A4BF1/A4BF2 Pulse Generator (Speed Sensors) ..................................................1 ......................42436M...........Switch, F4A33/W4A33 Pulse Generator (Speed Sensors) .............................................................1 ......................42436P ...........Switch, KM177 Pulse Generator .....................................................................................................1 ......................42437J ............Sensor, KM175-5/F4A22 Oil Temperature (TOT) 1989-95 ..............................................................1 ......................42437L ............Sensor, A4AF1/A4AF2/A4BF2/A4BF3/F4A32 Oil Temperature (TOT) 1993-99 .............................1 ......................42437M...........Sensor, F4A33/W4A33 Oil Temperature (Brass) ............................................................................1 ......................42437MA ........Sensor, F4A33/W4A33 Oil Temperature (TOT) (Plastic) 1991-99 ..................................................1 ......................42440C ...........Switch, KM175/KM177 Kickdown Servo 1985-88 ...........................................................................1 ......................42440E ...........Switch, KM175-5/KM177-8 Kickdown Servo 1989-Up ....................................................................1 ......................42440J ............Switch, KM176-5 Kickdown Servo ..................................................................................................1 ......................42440M...........Switch, F4A33/W4A33 Kickdown Servo .........................................................................................1 ......................

PART # MISC. COMPONENTS QTY. REFERENCE #

42484A ...........Plug, KM Series Servo Air Exhaust Elbow ......................................................................................1 ......................45245-3700042494M...........Filler Tube, F4A33/W4A33 (15” Long) ............................................................................................1 ......................42494MA ........Filler Tube, F4A33 (6” Long) ...........................................................................................................1 ......................

PART # HARD PARTS QTY. REFERENCE #

42500A ...........Pump, KM170 1979-86 ...................................................................................................................1 ......................42500B ...........Pump, KM171 Non Vented Body (Use With Vented Case) 1983-88 ...............................................1 ......................42500BA .........Pump, KM171 With Vented Body (Use With Non Vented Case) 1983-88 ......................................1 ......................42500C ...........Pump, KM175 Non Vented Body (Use With Vented Case) 1985-88 ...............................................1 ......................42500CA .........Pump, KM175 With Vented Body (Use With Non Vented Case) 1985-88 ......................................1 ......................42500D ...........Pump, KM172 Non Vented Body (Use With Vented Case) 1983-88 ...............................................1 ......................42500DA .........Pump, KM172 With Vented Body (Use With Non Vented Case) 1983-88 ......................................1 ......................42500E ...........Pump, KM175-5 1988-Up ...............................................................................................................1 ......................42500G ...........Pump, KM177-8 1989-Up ...............................................................................................................1 ......................42500H ...........Pump, KM171-5/KM176-5 (With 3 Rings On Input Shaft) (1 Bushing Direct Drum) 1989-Up ........1 ......................42500L ............Pump, A4AF1 (1 Bushing Direct Drum) 1991-99 (Ring Tower Measures 1 5/8” ........................From Washer Surface To The End) .................................................................................................1 ...................... 42500LB .........Pump, A4BF1 (2 Bushing Direct Drum) 1991-99 ............................................................................1 ......................42500LC .........Pump, A4BF2 (1 Bushing Direct Drum) 2000-Up (Ring Tower Measures 1 1/2” From Washer........................Surface To The End) .......................................................................................................................1 ......................42500LD .........Pump, A4AF3 (1 Bushing Direct Drum) 2000-Up (Ring Tower Measures 1 5/16” From Washer........................Surface To The End) .......................................................................................................................1 ......................42500LE .........Pump, A4BF3 (1 Caged Needle Bearing In Direct Drum) 2000-Up(Ring Tower Measures 1 5/16” ........................From Washer Surface To The End)(Has A Steel Sleeve On The End Where The Needle ........................Bearing Rides) ................................................................................................................................1 ......................42500M...........Pump, F4A33/W4A33 (With 1 Ring On Input Shaft) 1990-Up ........................................................1 ......................42500MA ........Pump, F4A33/W4A32/W4A33 (With 3 Rings On Input Shaft) (2 3/4” Long Stator Shaft)........................1990-Up ..........................................................................................................................................1 ......................42500MB ........Pump, F4A33/W4A32/W4A33 (With 3 Rings On Input Shaft) (2 1/2” Long Stator Shaft) ........................1990-Up ..........................................................................................................................................1 ......................42500P ...........Pump, KM177 (With 1 Ring Input Shaft) 1 Bushing Direct Drum 1987-88 ......................................1 ......................42500Y ...........Pump, KM172-5 1989-Up ...............................................................................................................1 ......................


7.3j

MIT

SU

BIS

HI


PART # HARD PARTS (Continued) QTY. REFERENCE #

42510B ...........Pump Body W/Gears, KM171/KM172/KM175 Non Vented (Use With Vented Case) 1983-88 .......1 ......................42510BA .........Pump Body W/Gears, KM171/KM172/KM175 Vented (Use With Non Vented Case) 1983-88 .......1 ......................42510E ...........Pump Body W/Gears, KM171-5/KM175-5/KM176-5/KM177-8 1988-Up ........................................1 ......................42510L ............Pump Body W/Gears, A4AF1/ A4BF1 (13 Teeth Inner Pump Gear) 1991-99 ................................1 ......................42510LC .........Pump Body W/Gears, A4AF3 / A4BF2 (11 Teeth Inner Pump Gear) 2000-Up ................................1 ......................42510M...........Pump Body W/Gears, F4A33/W4A32/W4A33 1990-Up .................................................................1 ......................42510Y ...........Pump Body W/Gears, KM172-5 1989-Up .......................................................................................1 ......................42520B ...........Stator, KM171/KM172/KM175 (With 3 Ring Input Shaft) Use With Vented Case 1983-88 .............1 ......................42520BA .........Stator, KM171/KM172/KM175 (With 3 Ring Input Shaft) For Non Vented Case) 1983-88 .............1 ......................42520E ...........Stator, KM175-5/KM172-5 (With 3 Ring Input Shaft) 2 Bushing Direct Drum 1988-Up ..................1 ......................42520G ...........Stator, KM177-8 (With 1 Ring On Input Shaft) 2 Bushing Direct Drum 1989-Up ............................1 ......................42520H ...........Stator, KM171-5/KM176-5 (With 3 Rings On Input Shaft) 1 Bushing Direct Drum 1989-Up ...........1 ......................42520HA .........Stator, KM171-5 (With 1 Ring On Input Shaft) 1 Bushing Direct Drum 1989-Up ............................1 ......................42520L ............Stator, A4AF1 (1 Bushing Direct Drum) 1991-99 (Ring Tower Measures 1 5/8” ........................From Washer Surface To The End) .................................................................................................1 ...................... 42520LB .........Stator, A4BF1 (2 Bushing Direct Drum) 1991-99 (Ring Tower Measures 1 7/8”........................From Washer Surface To The End) .................................................................................................1 ......................42520LC .........Stator, A4BF2 (1 Bushing Direct Drum) 2000-Up (Ring Tower Measures 1 1/2” From Washer........................Surface To The End) .......................................................................................................................1 ......................42520LD .........Stator, A4AF3 (1 Bushing Direct Drum) 2000-Up (Ring Tower Measures 1 5/16” From........................Washer Surface To The End) ..........................................................................................................1 ......................42520LE .........Stator, A4BF3 (1 Caged Needle Bearing In Direct Drum) (Ring Tower Measures 1 5/16” From........................Washer Surface To The End) (Has A Steel Sleeve On The End Where The Needle Bearing........................Rides) ..............................................................................................................................................1 ......................42520M...........Stator, F4A33/W4A33 (With 1 Ring On Input Shaft) 1990-Up ........................................................1 ......................42520MA ........Stator, F4A33/W4A32/W4A33 (With 3 Rings On Input Shaft) 1990-Up (2 3/4” Long Shaft) ...........1 ......................42520MB ........Stator, F4A33/W4A32/W4A33 (With 3 Rings On Input Shaft) 1990-Up (2 1/2” Long Shaft) ...........1 ......................42520P ...........Stator, KM177 (With 1 Ring Input Shaft) 1 Bushing Direct Drum 1987-88 ......................................1 ......................

PART # PUMP COMPONENTS QTY. REFERENCE #

42507A-5 ........Check Ball, KM Series Pump Stator ...............................................................................................1 ......................16011-1000042530E ...........Pump Gears, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF ...........................................1 ......................42530M...........Pump Gears, W4A32/F4A33/W4A33 ..............................................................................................1 ......................


42550C ...........Drum, KM175 Overdrive (3 Clutch) (1 Groove On ID) 1985-89 ......................................................1 ......................42550E ...........Drum, KM175-5/KM176-5/A4AF1 Overdrive (3 Clutch) (Stepped Lugs On OD) (1 1/8”Tall) ..........1 ......................42550EA .........Drum, KM175-5/KM176-5 Overdrive (3 Clutch) (Lugs On OD Are Not Stepped) ...........................1 ......................42550G ...........Drum, KM177-8/F4A23 Overdrive (4 Clutch) (Stepped Lugs On OD) ............................................1 ......................42550GA.........Drum, KM177-8/A4BF1/A4BF2 Overdrive (4 Clutch)(Lugs On OD Are Not Stepped)(1 1/4”Tall) ...1 ......................42550L ............Drum, A4BF Overdrive (3 Clutch) (1 Groove On OD)(1 5/8” Tall) ...................................................1 ......................42550LA .........Drum, A4AF3 Overdrive (5 Clutch)(No Groove On OD)(1 3/4” Tall)................................................1 ......................42550M...........Drum, F4A33/W4A32/W4A33 Overdrive (4 Clutch) (1.230”ID Piston) 1990-Up .............................1 ......................42554BK .........Drum, KM171 Forward With Input Shaft (2 Clutch) ........................................................................1 ......................42554C ...........Drum, KM175 Forward Without Shaft (3 Clutch) 5 5/8”OD 1985-89 ...............................................1 ......................42554DK.........Drum, KM172 Forward With Input Shaft (3 Clutch) ........................................................................1 ......................42554E ...........Drum, KM175-5 / (KM177-8 Some) / A4BF1 Forward Without Shaft (3 Clutch) 5 5/8”OD ........................(.640” Tall Inner Piston Hub) 1988-Up .............................................................................................1 ......................42554G ...........Drum, KM177-8 (Some) Forward Without Shaft (3 Clutch) 5 5/8”OD (.570” Tall Inner Piston........................Hub) 1994-Up ..................................................................................................................................1 ......................42554H ...........Drum, KM171-5 Forward Without Shaft (2 Clutch) (5 5/8”OD) 1989-Up .........................................1 ......................42554HK.........Drum, KM171-5 Forward With 3 Ring Input Shaft (2 Clutch) (5 5/8”OD) 1989-Up .........................1 ......................42554J ............Drum, KM176-5/A4AF1 Forward Without Shaft (2 Clutch) (5 5/8”OD) 1989-Up .............................1 ......................42554L ............Drum, A4BF2 Forward Without Shaft (5 Clutch) (5 1/2”OD) (With 1” Tall Inner Piston Hub) ........................2000-Up ..........................................................................................................................................1 ......................42554LA .........Drum, A4AF3 Forward Without Shaft (4 Clutch) (5 1/2”OD) (With 7/8” Tall Inner Piston Hub)........................2000-Up ..........................................................................................................................................1 ......................42554M...........Drum, F4A33/W4A33 Forward Without Shaft (5 Clutch) 6”OD 1990-Up ........................................1 ......................42554YK .........Drum, KM172-5 Forward With Input Shaft (3 Clutch) 1989-Up .......................................................1 ......................42555B ...........Drum, KM171 Direct (2 Clutch) 4.50”OD Piston (8 Lugs) 1983-88 .................................................1 ......................42555BA .........Drum, KM171 Direct (2 Clutch) 5.00”OD Piston (8 Lugs) 1983-88 .................................................1 ......................42555C ...........Drum, KM175 Direct (3 Clutch) 1 3/4” Tall (1 Bushing) 1985-89 .....................................................1 ......................42555D ...........Drum, KM172 Direct (3 Clutch) 1 1/2” Tall (1 Bushing) 1983-89 (Has A .085” Snap ........................Ring Groove For Snap Ring # 879) .................................................................................................1 ...................... 42555DA .........Drum, KM172 Direct (3 Clutch) 1 1/2” Tall (1 Bushing) 1983-89 (Has A .060” Snap ........................Ring Groove For Snap Ring # 879) .................................................................................................1 ......................


7.3k

MITS

UB

ISH

I


42555E ...........Drum, KM175-5/KM177-8/A4BF1 Direct (3 Clutch) 1 5/8” Tall (2 Bushing) 1988-Up .....................1 ......................42555H ...........Drum, KM171-5/KM176-5/A4AF Direct (2 Clutch) 1 Bushing (12 Lugs) 1989-Up ..........................1 ......................42555M...........Drum, F4A33/W4A33 Direct (4 Clutch) 2 Bushings 1990-Up .........................................................1 ......................42555L ............Drum, A4AF3 Direct Clutch (2 Clutch)(1.325” Tall)(1 Bushing 5/16” Wide)(Lugs Are 1/4” Down........................From The Top Of Drum) 2000-Up ...................................................................................................1 ......................42555LA .........Drum, A4BF3 Direct Clutch (3 Clutch)(1.550” Tall)(1 Bushing 1/2” Wide)(Lugs Are 1/2” Down........................From The Top Of Drum) 2000-Up ...................................................................................................1 ......................42555LE .........Drum, A4BF3 Direct Clutch (2 Clutch)(1.325” Tall)(1 Caged Needle Bearing Inside Instead........................Of A Bushing) ..................................................................................................................................1 ......................42555M...........Drum, F4A33/W4A33 Direct (4 Clutch)(2 Bushing) 1990-Up ..........................................................1 ......................42555Y ...........Drum, KM172-5 Direct (3 Clutch) 1 1/2” Tall (2 Bushing) 1989-Up .................................................1 ......................42560C ...........Piston Kit, KM175 Overdrive Clutch 1985-89 ..................................................................................1 ......................42560E ...........Piston Kit, KM175-5/KM176-5/A4AF Overdrive Clutch (Cast # D) 1988-Up ...................................1 ......................42560G ...........Piston Kit, KM177-8/A4BF1/A4BF2 Overdrive Clutch (Cast # E) 1989-Up (Steel Piston) ..............1 ......................42560LB .........Piston Kit, A4AF3 Overdrive Clutch (Aluminum Piston) ..................................................................1 ......................42560M...........Piston Kit, F4A33/W4A32/W4A33 Overdrive Clutch (Cast # C) 1990-Up .......................................1 ......................42564B ...........Piston Kit, KM171/KM172 Forward Clutch 1983-88 ........................................................................1 ......................42564C ...........Piston Kit, KM175 Forward Clutch 1985-89 ....................................................................................1 ......................42564E ...........Piston Kit, KM175-5/KM176-5/KM177-8/A4AF1/A4BF1 Forward Clutch 1988-Up .........................1 ......................42564H ...........Piston Kit, KM171-5/KM172-5 Forward Clutch 1989-Up .................................................................1 ......................42564L ............Piston Kit, A4AF3 Forward Clutch ...................................................................................................1 ......................42564M...........Piston Kit, F4A33/W4A33 Forward Clutch 1990-Up .......................................................................1 ......................42564N ...........Piston Kit, W4A32 Forward Clutch 1991-Up ...................................................................................1 ......................42565B ...........Piston Kit, KM171/KM172 Direct Clutch (4.500”OD Piston) 1983-88 .............................................1 ......................42565BA .........Piston Kit, KM171/KM172 Direct Clutch (5.000”OD Piston) 1983-88 .............................................1 ......................42565C ...........Piston Kit, KM175 Direct Clutch 1985-89 ........................................................................................1 ......................42565E ...........Piston Kit, KM175-5/W4A32/A4BF1/A4BF2 Direct Clutch 1988-Up ...............................................1 ......................42565H ...........Piston Kit, KM171-5/KM176-5/A4AF1 Direct Clutch 1989-Up ........................................................1 ......................42565L ............Piston Kit, A4AF3 Direct Clutch (Piston Cast #45490-22700) .........................................................1 ......................42565M...........Piston Kit, F4A33/W4A33 Direct Clutch 1990-Up ...........................................................................1 ......................42565Y ...........Piston Kit, KM172-5 Direct Clutch 1989-Up ....................................................................................1 ......................42567B ...........Piston Kit, KM171 Center Support (Low/Reverse Clutch) 1983-88 ................................................1 ......................42567C ...........Piston Kit, KM172/KM175 Center Support (Low/Reverse Clutch) 1983-89 ....................................1 ......................42567E ...........Piston Kit, KM172-5/KM175-5/KM177-8/A4BF1/A4BF2/W4A32 Center Support (Low/Reverse ........................Clutch) 1988-Up ..............................................................................................................................1 ......................42567H ...........Piston Kit, KM171-5/KM176-5/A4AF1/A4AF3/F4A32 Center Support (Low/Reverse Clutch)........................1989-Up ..........................................................................................................................................1 ......................42567M...........Piston Kit, F4A33/W4A33 Center Support (Low/Reverse Clutch) 1990-Up ....................................1 ......................42570C ...........Clutch Hub, KM175 Overdrive (2 Clutch) 26 Splines 1985-89 ........................................................1 ......................42570E ...........Clutch Hub, KM171-5/KM176-5/A4AF1/(A4BF1/A4BF2 Some) Overdrive (3 Clutch)(27 Splines)........................(4.030”OD)(40 Teeth Clutch Hub) 1980-Up ....................................................................................1 ......................42570G ...........Clutch Hub, KM177-8/W4A32 Overdrive (4 Clutch) 27 Splines (.930” Tall) 1989-Up .....................1 ......................42570L ............Clutch Hub, A4AF3 (A4BF1/A4BF2 Some) Overdrive (4 Clutch)(3.660”OD)(36 Teeth Clutch........................Hub) 2000-Up ..................................................................................................................................1 ......................42570M...........Clutch Hub, F4A33/W4A33 Overdrive (4 Clutch) 40 Teeth (4.030”OD)1990-Up ............................1 ......................42574B ...........Clutch Hub, KM171 Forward (10 Teeth) 1983-88 ...........................................................................1 ......................42574BA .........Clutch Hub, KM171 Forward (38 Teeth) 1983-88 ...........................................................................1 ......................42574C ...........Clutch Hub, Km172/KM175 Forward (38 Teeth) 1983-89 ...............................................................1 ......................42574E ...........Clutch Hub, KM172-5/KM177-5/Some KM177-8/A4BF1/A4BF2/W4A32 Forward (38 Teeth) ........................1988-Up ..........................................................................................................................................1 ......................42574G ...........Clutch Hub, Some KM177-8 Forward (38 Teeth) With 4.060”OD At Friction Splines .....................1 ......................42574H ...........Clutch Hub, KM171-5/KM176-5/A4AF Forward (38 Teeth) 1989-Up ..............................................1 ......................42574L ............Clutch Hub, A4BF2 Forward (38 Teeth)(5 Clutch)(1.510” Overall Height)(.960”Thick At ........................Friction Splines) ..............................................................................................................................1 ......................42574LA .........Clutch Hub, A4AF3 Forward (38 Teeth)(4 Clutch)(1.190” Overall Height)(.775” Thick At........................Friction Splines) ..............................................................................................................................1 ......................42574M...........Clutch Hub, F4A33/W4A33 Forward (42 Teeth) 5 Clutch (27 Splines) 1.580” Tall 1990-Up ...........1 ......................42583B ...........Planet Kit, KM171 1983-88 .............................................................................................................1 ......................42583C ...........Planet Kit, KM175 (26 Teeth Forward Sun Gear) 1985-89 .............................................................1 ......................42583CA .........Planet Kit, KM175 (29 Teeth Forward Sun Gear) 1985-89 .............................................................1 ......................42583D ...........Planet Kit, KM172 (15/16” Thick Low/Reverse Clutch Hub) 1983-88 .............................................1 ......................42583DA .........Planet Kit, KM172 (13/16” Thick Low/Reverse Clutch Hub) 1983-88 .............................................1 ......................42583E ...........Planet Kit, KM175-5 / A4AF-2 (No Groove) Lug Height Is .950” (Can Use 42583EA) 1988-Up .....1 ......................42583EA .........Planet Kit, KM175-5 / A4BF-2 (1 Groove) Lug Height Is .950” (Can Use 42583E) 1988-Up ..........1 ......................42583G ...........Planet Kit, KM177-8 (No Groove) 1989-Up (Planet With Sun Gears & Bearings Less ........................Ring Gear) Retro Fits With The 42583GA (Forward Sungear 29 Teeth / Reverse ........................Sun Gear 34 Teeth) .........................................................................................................................1 ......................42583GA.........Planet Kit, KM177-8/W4A32 (1 Groove) Can Use 42583G 1989-Up (Contains: Planet ........................W/Sprag, Forward & Reverse Sun Gears, Bearings, Races) .........................................................1 ......................42583H ...........Planet Kit, KM171-5 (No Groove) 1989-Up .....................................................................................1 ......................


7.3l

MIT

SU

BIS

HI



42583J ............Planet Kit, KM176-5/A4AF1/A4AF2 (Lug Height Is .844”) (Bearing #247 Has 1 Race........................On The Bottom) 1989-Up ................................................................................................................1 ......................42583LB .........Planet Kit, A4AF3 (Lug Height Is .844”)(Bearing #247 Has 2 Races) 2002-Up ..............................1 ......................42583LC .........Planet Kit, A4BF1/A4BF2 (Lug Height Is .950”) (Bearing #247 Has 2 Races) 2002-Up .................1 ......................42583M...........Planet Kit, F4A33/W4A33 1990-Up .................................................................................................1 ......................42583Y ...........Planet Kit, KM172-5 1989-Up .........................................................................................................1 ......................42584BK .........Planet W/Sprag, KM171 1983-88 ...................................................................................................1 ......................42584CK.........Planet W/Sprag, KM175 (Has A 26 Tooth Forward Sun Gear) 1985-89 .........................................1 ......................42584CA .........Planet W/Sprag, KM175 (Has A 29 Tooth Forward Sun Gear) 1985-89 .........................................1 ......................42584DK.........Planet W/Sprag, KM172 (15/16” Thick Low/Reverse Clutch Hub) 1983-88 ...................................1 ...................... 42584DAK ......Planet W/Sprag, KM172 (13/16” Thick Low/Reverse Clutch Hub) 1983-88 ...................................1 ......................42584EK .........Planet W/Sprag, KM175-5 (22 Teeth On Short Gears With No Groove) 1988-Up ..........................1 ......................42584EAK ......Planet W/Sprag, KM175-5 (22 Teeth On Short Gears With 1 Groove) 1988-Up ............................1 ......................42584EBK ......Planet W/Sprag, KM175-5 (19 Teeth On Short Gears With 1 Groove) 1988-Up ............................1 ......................42584GK ........Planet W/Sprag, KM177-8 (No Groove On Short Gears) 1989-Up .................................................1 ......................42584GAK ......Planet W/Sprag, KM177-8/W4A32 (With 1 Groove On Short Gears) 1989-Up ..............................1 ......................42584HK.........Planet W/Sprag, KM171-5 1989-Up ................................................................................................1 ......................42584JK .........Planet W/Sprag, KM176-5/A4AF 1989-Up ......................................................................................1 ......................42584MK ........Planet W/Sprag, F4A33/W4A33 1990-Up .......................................................................................1 ......................42584YK .........Planet W/Sprag, KM172-5 1989-Up ................................................................................................1 ......................42594B ...........Ring Gear, All KM (Except F4A33/W4A33) Annulus (74 Teeth)(22 Outer Lugs)(5 1/4”OD) ............1 ......................42594M...........Ring Gear, F4A33/W4A33 Annulus (5 7/8”OD) 1990-Up ................................................................1 ......................42604LB .........Hub, A4AF3 Annulus Gear (2.550” Overall Height)(3/4” Spline Length)(Uses A Nut To Hold ........................On The Gear) ..................................................................................................................................1 ......................42604LC .........Hub, A4BF1/A4BF2 Annulus Gear (2.940” Overall Height)(1 1/8” Spline Length)(Uses A Snap........................Ring To Hold On The Gear) .............................................................................................................1 ......................42605B ...........Hub, KM171 Annulus With 22 Teeth Gear & Ball Bearings 1983-88 ...............................................1 ......................42605C ...........Hub, KM175 Annulus With 20 Teeth Gear & Ball Bearings 1985-89 ...............................................1 ......................42605D ...........Hub, KM172 Annulus With 20 Teeth Gear & Ball Bearings 1983-88 ...............................................1 ......................42605E ...........Hub, KM175-5/KM176-5 Annulus With 24 Teeth Gear & Ball Bearings (No Groove) 1988-Up ......1 ......................42605EA .........Hub, KM175-5/KM176-5 Annulus With 24 Teeth Gear & Ball Bearings (1 Groove) 1988-Up .........1 ......................42605EB .........Hub, KM175-5/KM176-5 Annulus With 24 Teeth Gear & Ball Bearings (2 Groove) 1988-Up .........1 ......................42605G ...........Hub, KM177-8 Annulus With 24 Teeth Gear & Ball Bearings (No Groove) 1989-Up ......................1 ......................42605GA.........Hub, KM177-8 Annulus With 24 Teeth Gear & Ball Bearings (1 Groove) 1989-Up .........................1 ......................42605H ...........Hub, KM171-5 Annulus With 24 Teeth Gear & Ball Bearings 1989-Up ...........................................1 ......................42605L ............Hub, A4AF1 Annulus With 58 Teeth Gear & Ball Bearings 1991-Up ...............................................1 ......................42605LB .........Hub, A4AF3 (No Longer Available) Use 42604LB & 42710LB .......................................................1 ......................42605LC .........Hub, A4BF1/A4BF2 (No Longer Available) Use 42604LC & 42710LC ...........................................1 ......................42605M...........Hub, F4A33 Annulus With 35 Teeth Gear (3.680”OD) And Ball Bearings 1990-Up ........................1 ......................42605MA ........Hub, F4A33/W4A32/W4A33 Annulus With 35 Teeth Gear (3.705”OD) And Ball Bearings ........................1990-Up ..........................................................................................................................................1 ......................42605Y ...........Hub, KM172-5 Annulus With 23 Teeth Gear & Ball Bearings 1989-Up ...........................................1 ......................42612B ...........Sun Gear, KM171 Forward (26 Teeth) 3.780” Long 1983-88 ..........................................................1 ......................42612C ...........Sun Gear, KM175 Forward (26 Teeth) 3.195” Long (1.020”OD Of Shaft) 1985-89 .........................1 ......................42612CA .........Sun Gear, KM175 Forward (29 Teeth) 3.195” Long (1.020”OD Of Shaft) 1985-89 .........................1 ......................42612D ...........Sun Gear, KM172 Forward (26 Teeth) 3.930” Long 1983-88 ..........................................................1 ......................MD-71528542612DA .........Sun Gear, KM172 Forward (29 Teeth) 3.760” Long 1983-88 ..........................................................142612E ...........Sun Gear, KM175-5 Forward (26 Teeth) 3.195” Long (1.095”OD Of Shaft) 1.610”OD ........................Of Gear (No Groove) 1988-Up ........................................................................................................1 ......................MD-75806642612EA .........Sun Gear, KM175-5 Forward (26 Teeth) 3.195” Long (1.095”OD Of Shaft) 1.610”OD ........................Of Gear (1 Groove) 1988-Up ..........................................................................................................1 ...................... 42612EB .........Sun Gear, KM175-5 Forward (26 Teeth) 3.195” Long (1.095”OD Of Shaft) 1.775”OD ........................Of Gear (1 Groove) 1988-Up ..........................................................................................................1 ...................... 42612G ...........Sun Gear, KM177-8 Forward (29 Teeth) 3.195” Long (No Groove) 1989-Up .................................1 ......................42612GA.........Sun Gear, KM177-8/W4A32 Forward (29 Teeth) 3.195” Long (1 Groove) 1989-Up .......................1 ......................42612H ...........Sun Gear, KM171-5 Forward (26 Teeth) 3.740” Long 1989-Up ......................................................1 ......................MD-75803542612J ............Sun Gear, KM176-5 Forward (26 Teeth) 3.010” Long 1989-Up ......................................................1 ......................MD-75803842612LA .........Sun Gear, A4AF3 Forward (26 Teeth)(3.040” Long) .......................................................................1 ......................42612LB .........Sun Gear, A4BF1/A4BF2 Forward (29 Teeth)(1 Groove)(3.222” Long) ..........................................1 ......................42612M...........Sun Gear, F4A33/W4A33 Forward (29 Teeth) 3.435” Long 1990-Up .............................................1 ......................42612Y ...........Sun Gear, KM172-8 Forward (26 Teeth) 3.925” Long 1989-Up ......................................................1 ......................42614B ...........Sun Gear, KM171 Reverse (34 Teeth) 2.075” Long (No Groove) 1983-88 .....................................1 ......................42614C ...........Sun Gear, KM175 Reverse (34 Teeth) 2.275” Long (2 Grooves) With Snap Ring 1985-88 ............1 ......................42614D ...........Sun Gear, KM175 Reverse (34 Teeth) 2.275” Long (No Grooves) With Snap Ring 1985-88 .........1 ......................MD-71276642614DA .........Sun Gear, KM172 Reverse (34 Teeth) 2.075” Long 1983-88 ..........................................................1 ......................42614E ...........Sun Gear, KM175-5 Reverse (34 Teeth) 2.265” Long (No Groove) Takes 1 Snap Ring ........................And 1 Sealing Ring 1988-Up ...........................................................................................................1 ......................MD-758068


7.3m

MITS

UB

ISH

I


42614EA .........Sun Gear, KM175-5/A4BF1/A4BF2 Reverse (34 Teeth) 2.265” Long (1 Groove In Middle) ........................Takes 1 Snap Ring And 1 Sealing Ring 1988-Up ............................................................................1 ......................42614GA.........Sun Gear, KM177-8 Reverse (34 Teeth) 2.265” Long (1 Groove At Edge) Takes 1 Snap Ring ........................And 1 Sealing Ring 1989-Up ...........................................................................................................1 ......................MD-72218542614GB ........Sun Gear, KM177-8 Reverse (34 Teeth) 2.265” Long (No Groove) Takes 1 Snap Ring And........................1 Sealing Ring 1989-Up ..................................................................................................................1 ......................42614H ...........Sun Gear, KM171-5/KM176-5/A4AF1/A4AF3 Reverse (34 Teeth) 2.080” Long (Takes 1 Snap ........................Ring And 1 Sealing Ring 1989-Up ..................................................................................................1 ......................MD-75804042614M...........Sun Gear, F4A33/W4A33 Reverse (34 Teeth) 2.305” Long (Takes 1 Sealing Ring) 1990-Up ........1 ......................MD-73506042614Y ...........Sun Gear, KM172-5 Reverse (34 Teeth) 2.265” Long (Takes 1 Snap Ring & 1 Sealing Ring) ........................1989-Up ..........................................................................................................................................1 ......................42622B ...........Shell, KM171 (Kickdown Drum) 1983-88 ........................................................................................1 ......................42622C ...........Shell, KM172/KM175/KM177 (Kickdown Drum) 1983-89 ...............................................................1 ......................42622E ...........Shell, KM172-5/KM175-5/KM177-8/A4BF1/A4BF2/F4A32/W4A32 1989-Up (3 7/8” Overall ........................Height) .............................................................................................................................................1 ......................42622H ...........Shell, KM171-5/KM176-5/A4AF1/A4AF3 (3 1/2” Overall Height) 1989-Up .....................................1 ......................42622M...........Shell, F4A33/W4A33 (4 1/8” Overall Height) 1990-Up ....................................................................1 ......................42630B ...........Center Support, KM171/KM172 Some (Aluminum) 2.080” Wide (24 Teeth Steels) ........................1 Bushing 1983-88 ..........................................................................................................................1 ......................42630C ...........Center Support, KM175/KM172 Some (Aluminum) 2.275” Wide (24 Teeth Steels) ........................2 Bushings 1983-89 ........................................................................................................................1 ......................42630E ...........Center Support, KM172-5/KM175-5/KM177-8/A4BF1/A4BF2/W4A32 (Steel)(1.585” Overall ........................Thickness) 1988-Up (With The Support Laying On A Flat Surface (Front Side Down) Measure ........................Thru Center To Flat Surface) ...........................................................................................................1 ......................42630H ...........Center Support, KM171-5/KM176-5/A4AF1/A4AF3 (Steel)(1.460” Overall Thickness) 1989-Up........................(With The Support Laying On A Flat Surface (Front Side Down) Measure Thru Center To Flat ........................Surface) ...........................................................................................................................................1 ......................42630M...........Center Support, F4A33/W4A33 (Steel 1.535” Overall Thickness) 1990-Up (With The Support........................Laying On A Flat Surface (Front Side Down) Measure Thru Center To A Flat Surface) ..................1 ......................

PART # SPRAGS & ONE WAY CLUTCHES QTY. REFERENCE #

42654B ...........Sprag, KM170/KM171 Low/Reverse (26 Lug) Narrow 1983-88 ......................................................1 ......................MD-7318542654C ...........Sprag, KM172/KM175/KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF/W4A32 ........................Low/Reverse (26 Lug) Wide (Use 74658) 1983-Up ........................................................................1 ...................... 74658..............Sprag, KM172/KM175/KM171-5/KM172-5/KM175-5/KM177-8/A4AF1/A4BF1/A4BF2/W4A33 ........................Low/Reverse (26 Lug)(.700”Thick) 1983-Up ...................................................................................1 ...................... 42654L ............Sprag, KM176-5/A4AF3 Low/Reverse (26 Lugs)(.622”Thick) .........................................................1 ......................42654M...........Sprag, F4A33/W4A33 Low/Reverse (28 Lug) 1990-Up ..................................................................1 ......................


42670B ...........Input Shaft, KM171/KM172/KM171-5/KM172-5 (Sold With Forward Drum) ...................................1 ......................42670C ...........Input Shaft, KM175 (14 3/4” Long) 3 Ring (24 Spline) 1985-89 ......................................................1 ......................42670CA .........Input Shaft, KM175 (14 15/16” Long) 3 Ring (24 Spline) 1985-89 ..................................................1 ......................42670E ...........Input Shaft, KM175-5/A4BF1 (15 1/8” Long) 3 Ring (11/16”OD Of Rear Pilot) 1988-Up ................1 ......................42670EA .........Input Shaft, KM175-5/W4A32 (15 1/8” Long) 3 Ring (1/2”OD Rear Pilot) 1988-Up ........................1 ......................42670EB .........Input Shaft, KM175-5/Some 177-8 (15 7/16” Long) 3 Ring (1/2”OD Rear Pilot) 1988-Up ..............1 ......................42670G ...........Input Shaft, KM177-8 (15 7/16” Long) 1 Ring (11/16”OD Rear Pilot) 1989-Up ...............................1 ......................42670J ............Input Shaft, KM176-5/A4AF1 (14 1/2” Long) 3 Ring (11/16”OD Rear Pilot) 1990-Up (With 1 O-Ring........................On Shaft Under Drum) ....................................................................................................................1 ......................42670JA..........Input Shaft, A4AF3 (14 1/2” Long) 3 Ring (11/16”OD Rear Pilot) 1990-Up (With 2 O-Rings........................On Shaft Under Drum) ....................................................................................................................1 ......................42670L ............Input Shaft, A4BF2 (15 1/8” Long) 3 Ring (11/16”OD Rear Pilot) 1990-Up (With 2 O-Rings........................On Shaft Under Drum) ....................................................................................................................1 ......................42670M...........Input Shaft, F4A33/W4A33 (16 11/16” Long) 3 Ring 1990-Up ........................................................1 ......................42670MA ........Input Shaft, F4A33/W4A33 (16 1/16” Long) 1 Ring 1990-Up ..........................................................1 ......................42670MB ........Input Shaft, F4A33/W4A33 (16 5/8” Long) 3 Ring (.670”OD Rear Pilot) 1990-Up ..........................1 ......................42670MC ........Input Shaft, F4A33/W4A33 (16 5/8” Long) 3 Ring (.510”OD Rear Pilot) 1990-Up ..........................1 ......................42670P ...........Input Shaft, KM177 (1 Ring) 1987-88 .............................................................................................1 ......................42675C ...........Shaft, KM175 Overdrive (26 Spline) 3.060” Long 1985-89 .............................................................1 ......................42675E ...........Shaft, KM175-5/KM176-5/A4AF1/A4AF3/W4A32 Overdrive (27 Spline)(3.065” Long)1988-Up ....1 ......................42675G ...........Shaft, KM177-8 Overdrive (27 Spline) 3.340” Long (The Splines On The Overdrive End Are........................3/4” Long) 1989-Up .........................................................................................................................1 ......................42675L ............Shaft, A4BF1/A4BF2 Overdrive (27 Spline) 2.914” Long ................................................................1 ......................42675M...........Shaft, F4A33/W4A33 Overdrive (27 Spline) 3.340” Long (The Splines On The Overdrive ........................End Are 15/16” Long) 1990-Up .......................................................................................................1 ...................... 42677M...........Output Shaft, W4A32/W4A33 Rear (15 1/2” Long) 1990-Up ..........................................................1 ......................


7.3n

MIT

SU

BIS

HI



42679B ...........Idler Shaft, KM171/KM171-5/KM175-5/KM176-5 (1.175”OD) 2.740” Long 1983-Up ......................1 ......................42679C ...........Idler Shaft, KM172/KM175 (1.375”OD) 1983-89 .............................................................................1 ......................42679G ...........Idler Shaft, KM177-8 (1.175”OD) 3.085” Long 1989-Up .................................................................1 ......................42679M...........Idler Shaft, F4A33/W4A33 (1.175”OD) 3.110” Long 1990-Up .........................................................1 ......................42679Y ...........Idler Shaft, KM172-5/W4A32 (1.175”OD) 2.725” Long 1989-Up ....................................................1 ......................42680B ...........Governor, KM171/KM171-5/KM172-5 With Valve (1.095”OD Of Weight) 1983-Up ........................1 ......................42680D ...........Governor, KM172 With Valve (1.295”OD Of Weight) 1983-88 ........................................................1 ......................42686B ...........Cover, KM171/KM172/KM175 Pinion Shaft (Tin) 3.130”OD 1983-89 .............................................1 ......................42686E ...........Cover, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8 Pinion Shaft (Tin) 3.330”OD 1988-Up ....1 ......................42687B ...........Bracket, KM171/KM172/KM175 For Pinion Shaft Cover ................................................................1 ......................42687E ...........Bracket, Km171-5/KM172-5/KM175-5/KM176-5/KM177-8 For Pinion Shaft Cover ........................1 ......................42691B ...........Cover, KM171/KM171-5 Output Gear (Aluminum) ..........................................................................1 ......................42691D ...........Cover, KM172 Output Gear (Cast Iron) ...........................................................................................1 ......................42692C ...........Plate, KM175 Overdrive Adapter (3 Bolt) 1985-89 ..........................................................................1 ......................42692E ...........Plate, KM175-5/KM176-5/KM177-8 Overdrive Adapter (4 Bolt) 1988-Up .......................................1 ......................42692L ............Plate, A4AF1/A4BF1/A4BF2 Overdrive Adapter (5 Bolt)(.225” Thick) 1991-Up ..............................1 ......................42692LB .........Plate, A4AF3 Overdrive Adapter (4 Bolt)(4.109”OD)(Less Ball Bearings) ......................................1 ......................42692M...........Plate, F4A33/W4A32/W4A33 Overdrive Adapter (5 Bolt)(.275” Thick) 1990-Up ............................1 ......................42693B ...........Bracket, KM171/KM171-5/KM175-5/KM176-5 Holds Idler Shaft ....................................................1 ......................42693C ...........Bracket, KM172/KM175 Holds Idler Shaft .......................................................................................1 ......................42693G ...........Bracket, KM177-8 Holds Idler Shaft ................................................................................................1 ......................42693Y ...........Bracket, KM172-8 Holds Idler Shaft ................................................................................................1 ......................42710B ...........Gear, KM171 Transfer Drive (22 Teeth) No Groove 1983-88 ..........................................................1 ......................42710C ...........Gear, KM175 Transfer Drive (20 Teeth) 1 Groove 1985-89 ............................................................1 ......................42710D ...........Gear, KM172 Transfer Drive (20 Teeth) No Groove 1983-88 ..........................................................1 ......................42710E ...........Gear, KM175-5/KM176-5 Transfer Drive (24 Teeth) No Groove (1.020” Thick) 1988-Up ...............1 ......................42710EA .........Gear, KM175-5 Transfer Drive (24 Teeth) 2 Groove 1988-Up ........................................................1 ......................42710G ...........Gear, KM177-8 Transfer Drive (24 Teeth) No Groove (1.220” Thick) 1989-Up ...............................1 ......................42710H ...........Gear, KM171-5 Transfer Drive (24 Teeth) 1 Groove 1989-Up ........................................................1 ......................42710L ............Gear, A4AF1 Transfer Drive (58 Teeth) No Groove 1991-Up ..........................................................1 ......................42710LB .........Gear, A4AF3/A4BF2 Transfer Drive (53 Teeth) No Groove (Right Angled) (With 1 Bearing & ........................4 Bolt Flange) ..................................................................................................................................1 ......................42710LC .........Gear, A4BF1 Transfer Drive (53 Teeth) No Groove (Right Angled) (With Ball Bearing........................On Each Side Of Gear) ...................................................................................................................1 ......................42710M...........Gear, F4A33 Transfer Drive (35 Teeth) No Groove 1990-Up ..........................................................1 ......................42710MA ........Gear, W4A32/W4A33 Transfer Drive (35 Teeth) 1 Groove 1990-Up ..............................................1 ......................42710Y ...........Gear, KM172-5 Transfer Drive (23 Teeth) 1 Groove 1989-Up ........................................................1 ......................42712B ...........Gear, KM171 Driven Transfer (25 Teeth) No Groove 1983-88 ........................................................1 ......................42712C ...........Gear, KM175 Driven Transfer (23 Teeth) 2 Grooves 1985-89 ........................................................1 ......................42712D ...........Gear, KM172 Driven Transfer (23 Teeth) No Groove 1983-88 ........................................................1 ......................42712DA .........Gear, KM172 Driven Transfer (23 Teeth) 1 Groove 1983-88 ..........................................................1 ......................42712E ...........Gear, KM175-5/KM176-5 Driven Transfer (27 Teeth) No Groove 1988-Up ....................................1 ......................42712EA .........Gear, KM175-5 Driven Transfer (27 Teeth) 2 Groove 1988-Up ......................................................1 ......................42712EB .........Gear, KM175-5 Driven Transfer (27 Teeth) 1 Groove (.940” Thick) 1988-Up .................................1 ......................42712G ...........Gear, KM177-8 Driven Transfer (27 Teeth) No Groove (1.140” Thick) 1989-Up .............................1 ......................42712GA.........Gear, KM177-8 Driven Transfer (27 Teeth) 1 Groove (1.140” Thick) 1989-Up ...............................1 ......................42712H ...........Gear, KM171-5/KM172-5 Driven Transfer (27 Teeth) 1 Groove (.900” Thick) 1989-Up ..................1 ......................42712L ............Gear, A4AF1 Driven Transfer (60 Teeth)(No Groove) 1991-Up ......................................................1 ......................42712LA .........Gear, A4AF3 Driven Transfer (55 Teeth)(1 Groove) ........................................................................1 ......................42712LB .........Gear, A4BF1/A4BF2 Driven Transfer (55 Teeth)(No Groove) .........................................................1 ......................42712M...........Gear, F4A33 Driven Transfer (Is Made On The Pinion #730) 1990-Up ..........................................1 ......................42712MA ........Gear, W4A33 Driven Transfer (43 Teeth) 1 Groove (1.100” Thick) 1990-Up ..................................1 ......................42712N ...........Gear, W4A32 Driven Transfer (43 Teeth) 1 Groove (.860” Thick) 1991-Up ....................................1 ......................42714B ...........Idler Gear, KM171 (34 Teeth) No Groove 1983-88 .........................................................................1 ......................42714C ...........Idler Gear, KM175 (30 Teeth) 1 Groove 1985-89 ............................................................................1 ......................42714D ...........Idler Gear, KM172 (30 Teeth) No Groove 1983-88 .........................................................................1 ......................42714E ...........Idler Gear, KM175-5/KM176-5 (32 Teeth) No Groove (.930” Thick) 1988-Up .................................1 ......................42714EA .........Idler Gear, KM175-5 (32 Teeth) 2 Groove (.930” Thick) 1988-Up ...................................................1 ......................42714EB .........Idler Gear, KM175-5/KM176-5 (32 Teeth) 1 Groove (.930” Thick) 3.575”OD 1988-Up ...................1 ......................42714G ...........Idler Gear, KM177-8 (32 Teeth) NO Groove (1.115” Thick) 1989-Up ..............................................1 ......................42714GA.........Idler Gear, KM177-8 (32 Teeth) 1 Groove (1.115” Thick) 1989-Up .................................................1 ......................42714H ...........Idler Gear, KM171-5 (32 Teeth) 1 Groove (.874” Thick) 1989-Up ...................................................1 ......................42714HA .........Idler Gear, KM171-5 (32 Teeth) 2 Groove (.874” Thick) ..................................................................1 ......................42714M...........Idler Gear, F4A33 (38 Teeth) No Groove (4.080”OD) 1990-Up ......................................................1 ......................42714MA ........Idler Gear, F4A33/W4A32 (37 Teeth) 1 Groove (4.010”OD) 1990-Up ............................................1 ......................42714MB ........Idler Gear, F4A33 (37 Teeth) 2 Groove 1990-Up ............................................................................1 ......................42714MC ........Idler Gear, W4A33 (38 Teeth) No Groove (4.000”OD) 1990-Up .....................................................1 ......................42714MD ........Idler Gear, W4A33 (37 Teeth) No Groove (4.015”OD) 1990-Up .....................................................1 ......................


7.3o

MITS

UB

ISH

I


42714Y ...........Idler Gear, KM172-5 (32 Teeth) 1 Groove (.935” Thick) 3.630”OD 1989-Up ..................................1 ......................42715B ...........Differential, KM171 (57 Teeth Ring Gear) 19 Teeth Speed-O Gear ................................................1 ......................42715BA .........Differential, KM171 (57 Teeth Ring Gear) 36 Teeth Speed-O Gear (.925” Thick Ring Gear) .........1 ......................42715C ...........Differential, KM172/KM175 (51 Teeth Ring Gear) 19 Teeth Speed-O Gear ....................................1 ......................42715CA .........Differential, KM172/KM175 (51 Teeth Ring Gear) 36 Teeth Speed-O Gear ....................................1 ......................42715CC ........Differential, KM172/KM175 (52 Teeth Ring Gear) 1.125” Thick Gear (1 Groove) ........................36 Teeth Speed-O Gear ..................................................................................................................1 ......................42715E ...........Differential, KM175-5 (57 Teeth) 1.355” Thick Gear (1 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715EA .........Differential, KM175-5 (57 Teeth) 1.355” Thick Gear (2 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715EB .........Differential, KM175-5 (57 Teeth) 1.125” Thick Gear (1 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715EC.........Differential, KM175-5 (57 Teeth) 1.100” Thick Gear (1 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715EG ........Differential, KM175-5 (58 Teeth) 1.352” Thick Gear (2 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715G ...........Differential, KM177-8 (56 Teeth) 1.365” Thick Gear (1 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715GA.........Differential, KM177-8 (52 Teeth) 1.352” Thick Gear (2 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715GB ........Differential, KM177-8 (58 Teeth) 1.486” Thick Gear (3 Groove Gear) 36 Teeth Speed-O Gear .....1 ......................42715H ...........Differential, KM171-5/KM176-5 (64 Teeth) .925” Thick Gear (No Groove Gear) ............................1 ......................42715J ............Differential, KM176-5 (66 Teeth) .925” Thick Gear (1 Groove Gear) ..............................................1 ......................42715JC .........Differential, KM176-5 (65 Teeth) .925” Thick Gear (1 Groove Gear) ..............................................1 ......................42715L ............Differential, A4AF3 (74 Teeth Ring Gear)(1.127” Thick)(No Groove)(36 Teeth Speed-O Gear) .....1 ......................42715LA .........Differential, A4AF1 (74 Teeth Ring Gear)(1.127” Thick)(2 Groove)(36 Teeth Speed-O Gear)........................(Housing Is 5 1/8” Overall Height From Front To Rear)...................................................................1 ......................42715LAA .......Differential, A4AF1 (74 Teeth Ring Gear)(1.127” Thick)(2 Groove)(36 Teeth Speed-O Gear)........................(Housing Is 5 5/8” Overall Height From Front To Rear)...................................................................1 ......................42715LAB .......Differential, A4AF1 (74 Teeth Ring Gear)(1.127” Thick)(1 Groove)(36 Teeth Speed-O Gear) ........1 ......................42715LB .........Differential, A4AF2 (67 Teeth Ring Gear)(1.205” Thick)(No Groove)(36 Teeth Speed-O Gear) .....1 ......................42715LC .........Differential, A4AF2 (67 Teeth Ring Gear)(1.205” Thick)(2 Groove)(36 Teeth Speed-O Gear) ........1 ......................42715LD .........Differential, A4BF1 (69 Teeth Ring Gear)(1.205” Thick)(1 Groove)(36 Teeth Speed-O Gear) ........1 ......................42715M...........Differential, F4A33 (58 Teeth) 3 Groove (1.110”ID Axle Housing) Cone Bearings ..........................1 ......................42715MA ........Differential, F4A33 (57 Teeth) No Groove .......................................................................................1 ......................42715MAA ......Differential, F4A33 (57 Teeth) 2 Groove (1.110”ID Axle Housing) Cone Bearings ..........................1 ......................42715MAB ......Differential, F4A33 (58 Teeth) 3 Groove (1.041”ID Axle Housing) Cone Bearings..........................1 ......................42715MAC......Differential, F4A33 (58 Teeth) 2 Groove (1.041”ID Axle Housing) ..................................................1 ......................42715MB ........Differential, W4A32/W4A33 (72 Teeth Ring Gear) 1 Groove ..........................................................1 ......................42715MC ........Differential, W4A32/W4A33 (72 Teeth) 2 Groove (1.040”ID Axle Housing) Ball Bearings ..............1 ......................42715Y ...........Differential, KM172-5 (56 Teeth) 1.125” Thick (No Groove Gear) 36 Teeth Speed-O Gear ............1 ......................42718M...........Center Differential Assembly, W4A32/W4A33 (8 Bolt) 1990-Up .....................................................1 ......................42719M...........Viscous Coupling Unit, W4A32/W4A33 (4 1/4”OD) With 2 Splines ................................................1 ......................42725L ............Retainer, A4AF1 Differential (5 Bolt) Aluminum (3.850”OD Where The O-Ring Sets) ....................1 ......................42725LA .........Retainer, A4AF3/A4BF1/A4BF2 Differential (5 Bolt) Aluminum (4.090”OD Where The O-Ring ........................Sets) ................................................................................................................................................1 ......................42725M...........Retainer, F4A33/W4A32/W4A33 Differential (4 Bolt) Cast Iron ......................................................1 ......................42726LB .........Retainer, A4AF3/A4BF1/A4BF2 Differential Cup (2 Bolt)(Aluminum) .............................................1 ......................42726M...........Retainer, F4A33/W4A32/W4A33 Differential Cup (2 Bolt)(Aluminum) ............................................1 ......................42728M...........Retainer, W4A32/W4A33 Center Differential (Aluminum) 1990-Up ................................................1 ......................42730B ...........Pinion, KM171 (18 Teeth) Governor Type With Bearing On End Of Shaft 1983-88 ........................1 ......................42730C ...........Pinion, KM175 (16 Teeth) With Bearing On End Of Shaft 1985-89 ................................................1 ......................42730D ...........Pinion, KM172 (16 Teeth) Governor Type With Bearing On End Of Shaft 1983-88 ........................1 ......................42730E ...........Pinion, KM175-5 (16 Teeth) 1 Groove Next To Pilot (1.170” Thick Gear) Bearing On ........................Middle Of Shaft 1988-Up .................................................................................................................1 ......................42730EA .........Pinion, KM175-5 (16 Teeth) 1 Groove Next To Pilot (1.400” Thick Gear) Bearing On ........................Middle Of Shaft 1988-Up .................................................................................................................1 ......................42730EB .........Pinion, KM175-5 (16 Teeth) 1 Groove Next To Bearing (1.170” Thick Gear) Bearing ........................On Middle Of Shaft 1988-Up ...........................................................................................................1 ......................42730EC.........Pinion, KM175-5 (15 Teeth) No Groove (1.500” Thick Gear) .........................................................1 ......................42730ED.........Pinion, KM175-5 (15 Teeth) No Groove (1.432” Thick Gear) 10 1/2” Long (3 Grooves........................On Shaft Next To Bearing) ..............................................................................................................1 ......................42730EDA ......Pinion, KM175-5 (15 Teeth) No Groove (1.432” Thick Gear) 10 1/2” Long (3 Grooves........................On Shaft, 2 Next To The Bearing ....................................................................................................1 ......................42730EE .........Pinion, KM175-5 (16 Teeth) 1 Groove (1 3/8” Thick Gear) 10 1/2” Long (3 Grooves On Shaft) .....1 ......................42730EF .........Pinion, KM175-5 (16 Teeth) 1 Groove (1 3/8” Thick Gear) 10 1/2” Long (2 Grooves On Shaft) .....1 ......................42730EG ........Pinion, KM175-5 (15 Teeth) 1 Groove (10 1/2” Long) 3 Grooves On Shaft ....................................1 ......................42730EH.........Pinion, KM175-5 (15 Teeth) No Grooves (1.580” Thick Gear) 10 1/2” Long (3 Grooves ........................On Shaft) .........................................................................................................................................1 ......................42730G ...........Pinion, KM177-8 (17 Teeth) 2.370”OD Of Gear 1989-Up (Bearing On Middle Of Shaft) ................1 ......................42730H ...........Pinion, KM171-5 (20 Teeth) No Groove (Bearing On End Of Shaft) 1989-Up ................................1 ......................42730HA .........Pinion, KM171-5 (20 Teeth) 2 Grooves (Bearing On End Of Shaft) 1989-Up .................................1 ......................42730J ............Pinion, KM176-5 (18 Teeth) 1 Groove (2.180”OD Of Gear) 1989-Up (Bearing On Middle ........................Of Shaft) ..........................................................................................................................................1 ......................42730JA..........Pinion, KM176-5 (17 Teeth) No Groove (2.075”OD Of Gear) 1989-Up (Bearing On Middle ........................Of Shaft) ..........................................................................................................................................1 ......................


7.3p

MIT

SU

BIS

HI



42730JB .........Pinion, KM176-5 (17 Teeth) 1 Groove (2.075”OD Of Gear) 1989-Up (Bearing On Middle ........................Of Shaft) ..........................................................................................................................................1 ......................42730JC .........Pinion, KM176-5 (16 Teeth) 1 Groove (2.235”OD Of Gear) 1989-Up (Bearing On Middle ........................Of Shaft) ..........................................................................................................................................1 ......................42730JD .........Pinion, KM176-5 (18 Teeth) 2 Groove (2.180”OD Of Gear) 1989-Up (Bearing On Middle ........................Of Shaft) ..........................................................................................................................................1 ......................42730JE .........Pinion, KM176-5 (18 Teeth) No Groove (2.250”OD Of Gear) 1989-Up .........................................1 ......................42730LA .........Pinion, A4AF1 (21 Teeth Gear)(2.430”OD)(No Groove) Bearing On Middle Of ........................Shaft (9 1/2” Long) ..........................................................................................................................1 ......................42730LB .........Pinion, A4AF3 (19 Teeth Gear)(No Groove)(1 ID Groove On Shaft)(9 3/4” Long) ..........................1 ......................42730LC .........Pinion, A4AF2 (19 Teeth Gear)(2.475”OD)(No Groove) Bearing On Middle Of ........................Shaft (10 “ Long) .............................................................................................................................1 ......................42730LD .........Pinion, A4BF1 (18 Teeth)(No Groove)(1 ID Groove In Middle Of Shaft)(10” Long) ........................1 ......................42730LE .........Pinion, A4BF2 (16 Teeth)(No Groove)(10 1/4” Long) ......................................................................1 ......................42730M...........Pinion, F4A33 (16 Teeth) With 43 Teeth Transfer Gear 1990-Up ...................................................1 ......................42730MA ........Pinion, F4A33 (18 Teeth) 3 Groove (With 43 Teeth Transfer Gear) 1990-Up .................................1 ......................42730MAA ......Pinion, F4A33 (18 Teeth) 2 Groove (With 43 Teeth Transfer Gear) 1990-Up .................................1 ......................42730MB ........Pinion, F4A33 (20 Teeth) With 43 Teeth Transfer Gear 1990-Up ....................................................1 ......................42730MC ........Pinion, W4A32/W4A33 (20 Teeth) 1 Groove On Edge (7 1/4” Long) 1990-Up ...............................1 ......................42730MD ........Pinion, W4A33 (20 Teeth) 1 Groove In Center (7 1/4” Long) 1990-Up ...........................................1 ......................42730Y ...........Pinion, KM172-5 (17 Teeth) Governor Type (With Bearing On End) 1989-Up ................................1 ......................42734M...........Retainer, W4A32/W4A33 Pinion (Aluminum) 3 Bolt 1990-Up .........................................................1 ......................42735M...........Retainer, F4A33 Driven Transfer Gear (2.955”ID) 1990-Up (Without Oil Shield) ............................1 ......................42735MA ........Retainer, F4A33 Driven Transfer Gear (3.030”ID) 1990-Up (Without Tin Oil Shield) ......................1 ......................42735MB ........Retainer, W4A33 Driven Transfer Gear (2.955”ID) 1990-Up (With Tin Oil Shield) ..........................1 ......................42735MC ........Retainer, W4A32/W4A33 Driven Transfer Gear (2.955”ID) 1990-Up (With Tin Oil Shield)........................Machined O-Ring Area Is 13/16” Wide ............................................................................................1 ......................42740B ...........Valve Body, KM171 (1 Solenoid) Round Connector (Cast # 3A/T3 Filter Side) ..............................1 ......................42740BA .........Valve Body, KM171 (1 Solenoid) Square Connector Z(Cast # H-172-2) .........................................1 ......................42740C ...........Valve Body, KM175 (4 Solenoid) Round Connector (Cast # 175 Filter Side)..................................1 ......................42740D ...........Valve Body, KM172 (1 Solenoid) Round Connector (Cast # 3A/T1 Filter Side) ..............................1 ......................42740E ...........Valve Body, KM175-5 (4 Solenoid) Square Connector (Cast # 177 Filter Side) .............................1 ......................42740EA .........Valve Body, KM175-5 (4 Solenoid) Square Connector (Cast # 3A32 Filter Side) ...........................1 ......................42740EB .........Valve Body, KM175-5/A4AF (4 Solenoid) Square Connector (Cast # 4A3) Long ........................Wire Harness ..................................................................................................................................1 ......................42740EC.........Valve Body, KM175-5/A4AF (4 Solenoid) Square Connector (Cast # DOHC 8) Long........................Wire Harness ..................................................................................................................................1 ......................42740G ...........Valve Body, KM177-8 (3 Solenoid) Square Connector (Cast # 4AT1A Filter Side) .........................1 ......................42740H ...........Valve Body, KM171-5 (1 Solenoid) Square Connector (Cast # 3A/T3 Filter Side) ..........................1 ......................42740J ............Valve Body, KM176-5 (4 Solenoid) Square Connector (Cast # 4AT Filter Side) 14” Long ........................Wire Harness ..................................................................................................................................1 ......................42740JA..........Valve Body, KM176-5 (4 Solenoid) Square Connector (Cast # 4AT Filter Side) 27” Long ........................Wire Harness ..................................................................................................................................1 ......................42740LA .........Valve Body, A4AF1 (4 Solenoid) Square Connector (Cast # A4AF1 Filter Side) ............................1 ......................42740LB .........Valve Body, A4AF (4 Solenoid) Square Connector (Cast # X-3 Filter Side) ....................................1 ......................42740LC .........Valve Body, A4BF1/A4BF2 (4 Solenoid) Square Connector (Cast # A4AF2 Filter Side) ................1 ......................42740LD .........Valve Body, A4AF3 (6 Solenoid) (Cast # A4AF3 On Both Sides) ....................................................1 ......................42740LE .........Valve Body, A4AF (4 Solenoid) Square Connector (Cast # V-6 #3 Filter Side) ...............................1 ......................42740M...........Valve Body, F4A33 (3 Solenoid) Square Connector (Cast # 4A31 Filter Side) ...............................1 ......................42740MA ........Valve Body, F4A33 (4 Solenoid) Square Connector (Cast # 4A33 Filter Side) ...............................1 ......................42740MB ........Valve Body, W4A33 (3 Solenoid) Square Connector (Cast # 4A33 Filter Side) ..............................1 ......................42740N ...........Valve Body, W4A332 (4 Solenoid) Square Connector (Cast # 4A36 Filter Side) ............................1 ......................42740Y ...........Valve Body, KM172-5 (1 Solenoid) Square Connector (Cast # 3A/T6 Filter Side) ..........................1 ......................

PART # VALVE BODY COMPONENTS QTY REFERENCE #

S42741AM-1...Manual Valve, KM Series Increases Converter Charge Pressure (Sonnax) ...................................1 ......................41750-03

PART # HARDPARTS (Continued) QTY REFERENCE #

42750B ...........Bell Housing, KM171 (14 Bolt) 4 Dowels To Case (.870”ID Speed-O Hole) 1983-88 .....................1 ......................42750BA .........Bell Housing, KM171 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) 1983-88 ...................1 ......................42750C ...........Bell Housing, KM175/KM172-5/KM175-5 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) ........................Cast # KM175-5 1985-Up (Uses Aluminum Spacer) .......................................................................1 ......................42750D ...........Bell Housing, KM172 (13 Bolt) 4 Dowels To Case (.870”ID Speed-O Hole) 1983-88 .....................1 ......................42750DA .........Bell Housing, KM172 (14 Bolt) 4 Dowels To Case (.870”ID Speed-O Hole) 1983-88 .....................1 ......................42750DB.........Bell Housing, KM172 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) 1983-88 ...................1 ......................42750E ...........Bell Housing, KM175-5 (14 Bolt) 4 Dowels To Case (.870”ID Speed-O Hole) Cast # F4A22 ........................(Double Starter Location) 1989-Up .................................................................................................1 ......................


7.3q

MITS

UB

ISH

I


42750EA .........Bell Housing, KM175-5 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) Cast # F4A22 ........................(Double Starter Location) 1989-Up .................................................................................................1 ...................... 42750G ...........Bell Housing, KM177-8 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) Cast # 177 ........................(Uses An Aluminum Spacer Under Pump) ......................................................................................1 ...................... 42750H ...........Bell Housing, KM171-5 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) ........................Cast # KM170-1 1989-Up ...............................................................................................................1 ......................42750HA .........Bell Housing, KM171-5 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) Cast #F4A21 ........................(Double Starter Location) 1989-Up .................................................................................................1 ......................42750J ............Bell Housing, KM176-5 (14 Bolt) 4 Dowels To Case (1.100”ID Speed-O Hole) Cast # KM171 ........................1989-Up ..........................................................................................................................................1 ......................42757M...........Idler Cover, F4A33/W4A33 (6 Bolt) Tin 1990-Up ............................................................................1 ......................42758L ............Differential Cover, F4A33 (A4AF-1) 13 Bolt (Tin) 1991-Up .............................................................1 ......................42758LB .........Differential Cover, A4AF3/A4BF1/A4BF2 (13 Bolt)(Aluminum) .......................................................1 ......................42758M...........Differential Cover, F4A33/W4A33 (12 Bolt) Tin 1990-Up ................................................................1 ......................42758MA ........Differential Cover, F4A33 (12 Bolt) Aluminum 1990-Up ..................................................................1 ......................42760B ...........Case, KM171 (14 Bolt) 4 Dowels To Bell (Cast # 171) Non Vented (12 Pan Bolts, But Case........................Has 13 Holes) 1983-88 ...................................................................................................................1 ......................42760BA .........Case, KM171 (14 Bolt) 4 Dowels To Bell (Cast # 171) Vented Case (12 Pan Bolts, But ........................The Case Has 13 Holes) 1983-88 ...................................................................................................1 ......................42760C ...........Case, KM175 (14 Bolts) 4 Dowels To Bell (Cast # 175) Non Vented Case (12 Pan Bolts, ........................But The Case Has 13 Holes) 1985-89 ............................................................................................1 ...................... 42760CA .........Case, KM175 (14 Bolt) 4 Dowels To Bell (Cast # 175) Vented Case (12 Pan Bolts, But ........................The Case Has 13 Holes) 1985-89 ...................................................................................................1 ...................... 42760D ...........Case, KM172 (13 Bolt) 4 Dowels To Bell (Cast # 175) Non Vented Case (12 Pan Bolts, But ........................The Case Has 13 Holes) 1983-88 ...................................................................................................1 ...................... 42760DA .........Case, KM172 (13 Bolt) 4 Dowels To Bell (Cast # 175) Vented Case (12 Pan Bolts, But ........................The Case Has 13 Holes) 1983-88 ...................................................................................................1 ...................... 42760DB.........Case, KM172 (14 Bolt) 4 Dowels To Bell (Cast # 175) Non Vented Case (12 Pan Bolts, But ........................The Case Has 13 Holes) 1983-88 ...................................................................................................1 ...................... 42760DC ........Case, KM172 (14 Bolt) 4 Dowels To Bell (Cast # 175) Vented Case (12 Pan Bolts, But ........................The Case Has 13 Holes) 1983-88 ...................................................................................................1 ...................... 42760E ...........Case, KM175-5 (14 Bolt) 4 Dowels To Bell (Cast # S-KM175) 12 Pan Bolts, But The ........................Case Has 13 Holes 1988-Up ..........................................................................................................1 ...................... 42760EA .........Case, KM175-5 (14 Bolt) 4 Dowels To Case (Cast # F4A22) 12 Pan Bolts, But The ........................Case Has 13 Holes (Double Starter) 1988-Up ................................................................................1 ...................... 42760G ...........Case, KM177-8 (14 Bolt) 4 Dowels To Bell (Cast # 177) 13 Pan Bolts 1989-Up ............................1 ......................42760GA.........Case, KM177-8 (14 Bolt) 4 Dowels To Bell (Cast # F4A23) 13 Pan Bolts 1989-Up .......................1 ......................42760H ...........Case, KM171-5 (14 Bolt) 4 Dowels To Bell (Cast # S-KM171) 12 Pan Bolts, But The Case........................Has 13 Holes 1989-Up ....................................................................................................................1 ......................42760HA .........Case, KM171-5 (14 Bolt) 4 Dowels To Case (Cast # F3A21-S) 12 Pan Bolts, But The........................Case Has 13 Holes 1989-Up ..........................................................................................................1 ......................42760J ............Case, KM176-5 (14 Bolt) 4 Dowels To Bell (Cast # KM176) 12 Pan Bolts 1989-Up .......................1 ......................42760L ............Case, A4AF1 (4 3/8” Top Bolts) 2WD (Cast # A4AF1) 1991-Up .....................................................1 ......................42760LA .........Case, A4AF (5 1/8” Top Bolts) 2WD (Cast # A4AF2) 1991-Up .......................................................1 ......................42760LB .........Case, A4AF3 (5 1/8” Top Bolts) 2WD (Cast # A4AF3) 2000-Up (Uses A 6 Solenoid Valve Body)........................(13 3/4” Long Bell To Rear) .............................................................................................................1 ......................42760LC .........Case, A4BF1 (5 1/8” Top Bolts) 2WD (Cast # A4BF) 1991-Up (Uses A 4 Solenoid Valve Body)........................(14 1/8” Long Bell To Rear) .............................................................................................................1 ......................42760LD .........Case, A4BF2 (5 1/8” Top Bolts) 2WD (Cast # A4BF) 2000-Up (Uses A 6 Solenoid Valve Body)........................(14 1/8” Long Bell To Rear) .............................................................................................................1 ......................42760M...........Case, F4A33 (4 3/8” Top Bolts) 2WD (Cast # F4A33EN) 1990-Up .................................................1 ......................42760MA ........Case, F4A33 (3 9/16” Top Bolts) 2WD (Cast # F4A33EVS) 1990-Up (Detent For The Rooster ........................Comb Bolts Into The Case) .............................................................................................................1 ......................42760MAA ......Case, F4A33 (3 9/16” Top bolts) 2WD (Cast # F4A33EV) 1990-Up (Detent For The Rooster........................Comb Is Made In The Case) ...........................................................................................................1 ......................42760MB ........Case, W4A33 (4 3/8” Top Bolts) AWD (Cast # F4A33) 1990-Up (Detent For Rooster Comb........................Is Made In The Case) ......................................................................................................................1 ......................42760MBA ......Case, W4A33 (4 3/8” Top Bolts) 2WD (Cast # F4A33ENS) 1990-Up (Detent For The Rooster........................Comb Bolts Into The Case) .............................................................................................................1 ......................42760MC ........Case, W4A33 (4 1/8” Top Bolts) AWD (Cast # W4A33) 1990-Up ...................................................1 ......................42760N ...........Case, W4A32 (4 3/8” Top Bolts) AWD (Cast # W4A32) 1991-Up (Double Starter Location) ..........1 ......................42760NA .........Case, W4A32 (4 3/8” Top Bolts) AWD (Cast # W4A32) Single Starter Location .............................1 ......................42760Y ...........Case, KM172-5 (14 Bolt) 4 Dowels To Bell (Cast # F3A22) 12 Pan Bolts 1989-Up .......................1 ......................42762C ...........Housing, KM175 Overdrive (Cover) 3 Bolt 1985-89 ........................................................................1 ......................42762E ...........Housing, KM175-5 Overdrive (Cover) 4 Bolt (Cast # S-KM175) 1988-Up ......................................1 ......................42762EA .........Housing, KM175-5 Overdrive (Cover) 4 Bolt (Cast # F4A22) 1989-Up (With Speed Sensor) ........1 ......................42762G ...........Housing, KM177-8 Overdrive (Cover) 4 Bolt (Cast # KM177) 1989-UP .........................................1 ......................42762GA.........Housing, KM177 Overdrive (Cover) 4 Bolt (Cast # F4A23) With Speed Sensor Hole ....................1 ......................42762L ............Housing, A4AF1/A4AF2 Overdrive (Cover) 4 Bolt (Round)(With Speed Sensor Hole) 1991-99 ....1 ......................42762LC .........Housing, A4AF3 Overdrive (Cover)(12 Bolt)(With Speed Sensor Hole) 2000-Up ..........................1 ......................


7.3r

MIT

SU

BIS

HI


KM170 thru W4A33 FWD 3 & 4 SpeedPART # HARD PARTS (Continued) QTY. REFERENCE #

42762M...........Housing, F4A33/W4A32/W4A33 Overdrive (4 Bolt) Cast # W4A32 (Uses 1.220”OD ........................Bearing #223) ..................................................................................................................................1 ......................42762MA ........Housing, F4A33/W4A32/W4A33 Overdrive (4 Bolt) Cast # W4A32 (Uses 1.180”OD ........................Bearing #223) ..................................................................................................................................1 ......................42764C ...........Plate, KM175 Pump Spacer To Case (16 Hole) Aluminum 1985-89 ...............................................1 ......................42764D ...........Plate, KM172 Pump Spacer To Case (15 Hole) Aluminum 1983-89 ...............................................1 ......................42764E ...........Plate, KM175-5 Pump Spacer To Case (Aluminum) 1988-Up ........................................................1 ......................42764G ...........Plate, KM177-8 Pump Spacer To Case (Aluminum) 1989-Up ........................................................1 ......................42765B ...........Pan, KM171/KM172/KM175 Bottom (12 Bolt) No Drain Plug 1983-89 ...........................................1 ......................42765E ...........Pan, KM171-5/KM175-5/KM176-5 Bottom (12 Bolt) With Drain Plug .............................................1 ......................42765G ...........Pan, KM177-8 Bottom (13 Bolt) With Side Drain Plug ....................................................................1 ......................42765GA.........Pan, KM177-8 Bottom (13 Bolt) With Bottom Drain Plug ................................................................1 ......................42765L ............Pan, A4BF1/A4BF2 Bottom (13 Bolt) With Drain Plug Facing Rear Cover 1991-Up ......................1 ......................42765LB .........Pan, A4AF3 Bottom (13 Bolt) With Drain Plug Facing Servo Side Of Case ...................................1 ......................42765M...........Pan, F4A33/W4A32/W4A33 Bottom (14 Bolt) With Drain Plug 1990-Up ........................................1 ......................42765Y ...........Pan, KM172-5 Bottom (12 Bolt) With Drain Plug 1989-Up .............................................................1 ......................42771LB .........Spacer Plate, A4AF3 Case To Overdrive Cover (Aluminum)(12 Bolt)(1.030”Thick) .......................1 ......................42774B ...........Driven Speed-O Gear, KM171 With Housing (17 Teeth) 1983-89 ..................................................1 ......................42774C ...........Driven Speed-O Housing, KM175/KM171-5/KM172-5/KM175-5/KM176-5/KM177-8 ........................With Housing (31 Teeth) 1985-UP ...................................................................................................1 ...................... 42774D ...........Driven Speed-O Gear, KM172 With Housing (16 Teeth) 1983-88 ..................................................1 ......................42774L ............Driven Speed-O Gear, A4AF1/A4AF3 With Housing (32 Teeth) 1991-Up ......................................1 ......................42774LA .........Driven Speed-O Gear, A4BF1/A4BF2 With Housing (31 Teeth) .....................................................1 ......................42774M...........Driven Speed-O Gear, F4A33/W4A33 With Housing (29 Teeth) 1990-Up ......................................1 ......................42774N ...........Driven Speed-O Gear, W4A32 With Housing (28 Teeth) 1991-Up .................................................1 ......................42775A ...........Bolt, KM Series Converter (10mm X 1.5” Thread) ........................................................................ AR .....................42775E ...........Bolt, KM Series Converter (10mm X 1.25” Thread) ...................................................................... AR .....................42781EK .........Bolt Set, KM175-5/KM176-5/KM177-8 Overdrive Plate To Case (4 Pieces) ...................................1 ......................42781LK .........Bolt Set, A4BF1/A4BF2 For Overdrive Adapter # 692 (T40 Torx Head)(.670”Long)(5 Pieces) .......1 ......................42781LBK .......Bolt Set, A4AF3 For Double Ball Bearing Flange #692 (T40 Torx Head)(1.107” Long)(4 Pieces) ..1 ......................42795LB .........Nut, A4AF3 Holds Transfer Drive Gear To Annulus Hub # 604 (1.438”ID) ......................................1 ......................42796L ............Nut, A4AF1/A4AF3/A4BF1/A4BF2 Holds Transfer Driven Gear To The Pinion Shaft (.888”ID)......1 ......................42857B ...........Wave Ring, KM171/KM172/KM175 Low/Reverse (5 3/16”OD) 1983-89 ........................................1 ......................MD-070739942857G ...........Wave Ring, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/A4BF1/A4BF2/........................W4A32 Low/Reverse (5 7/16”OD) 1988-Up ....................................................................................1 ......................MD-71983042857M...........Wave Ring, F4A33/W4A33 Low/Reverse 1990-Up .........................................................................1 ......................42858M...........Wave Plate, F4A33 Forward Clutch (Bottom) 7 Tab .......................................................................1 ......................42858MA ........Wave Ring, W4A33 Forward Clutch (Bottom) No Tab ....................................................................1 ......................42861C ...........Snap Ring, KM Overdrive Pressure Plate (.040”) 1985-Up ............................................................1 ......................MD-75603342861CA .........Snap Ring, KM Overdrive Pressure Plate (.050”) 1985-Up ............................................................1 ......................MD75603442861CB.........Snap Ring, KM Overdrive Pressure Plate (.060”) 1985-Up ............................................................1 ......................MD-75603542861CC ........Snap Ring, KM Overdrive Pressure Plate (.070”) 1985-Up ............................................................1 ......................MD-75603642861CD ........Snap Ring, KM Overdrive Pressure Plate (.080”) 1985-Up ............................................................1 ......................MD-75603742862C ...........Snap Ring, KM175/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/W4A32 Holds Retainer ........................To Overdrive Drum 1985-Up ...........................................................................................................1 ......................42862LB .........Snap Ring, A4AF3 Holds Retainer To Overdrive Drum ...................................................................1 ......................42862M...........Snap Ring, F4A33/W4A33 Holds Retainer To Overdrive Drum 1990-Up .......................................1 ......................42863C ...........Wire Ring, KM175/KM175-5/KM176-5/KM177-8/A4AF1/A4BF2/W4A32 Between Snap ........................Ring & Overdrive Retainer 1985-Up ...............................................................................................1 ......................42863M...........Wire Ring, F4A33/W4A33 Between Snap Ring & Overdrive Retainer 1990-Up .............................1 ......................42869B ...........Snap Ring, KM171/KM172/KM175/KM171-5/KM176-5 Servo Cover To Piston .............................1 ......................42869E ...........Snap Ring, KM175-5/KM177-8 Servo Cover To Piston ..................................................................1 ......................42869M...........Snap Ring, F4A33/W4A33 Servo Cover To Piston 1990-Up ..........................................................1 ......................42869N ...........Snap Ring, W4A32 Servo Cover To Piston 1991-Up ......................................................................1 ......................42877B ...........Snap Ring, KM171/KM172/KM175/KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/........................A4AF1/A4BF1/W4A32 Forward Drum Spring Retainer ..................................................................1 ...................... 42877L ............Snap Ring, A4AF3 Forward Drum Spring Retainer (.060” Thick) ...................................................1 ......................42877M...........Snap Ring, F4A33/W4A33 Forward Drum Spring Retainer 1990-Up .............................................1 ......................42878B ...........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.063”) .....................................2 ......................MD-95563042878BA .........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.071”) .....................................2 ......................MD-95563142878BB .........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.079”) .....................................2 ......................MD-95563242878BC.........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.087”) .....................................2 ......................MD-95563342878BD.........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.094”) .....................................2 ......................MD-95563442878BE .........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.102”) .....................................2 ......................MD-95563542878BG ........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.110”) ......................................2 ......................MD-95563642878BH.........Snap Ring, All KM Except F4A33/W4A33 Forward & Direct Drum (.118”) ......................................2 ......................MD-955637

7.3s

MITS

UB

ISH

I


FWD 3 & 4 Speed KM170 thru W4A3342879B ...........Snap Ring, KM171 Direct Drum Retainer .......................................................................................1 ......................42879C ...........Snap Ring, KM172/KM175 Direct Drum Retainer ...........................................................................1 ......................42879E ...........Snap Ring, KM175-5/KM177-8/A4BF1/A4BF2/W4A32 Direct Drum Retainer ........................(.155”Thick, ID To OD) ....................................................................................................................1 ......................42879H ...........Snap Ring, KM171-5/KM176-5/A4AF1 Direct Drum Retainer ........................................................1 ......................42879L ............Snap Ring, A4AF3 Direct Drum Retainer (.120” Thick, ID To OD) ..................................................1 ......................42879M...........Snap Ring, F4A33/W4A33 Direct Drum Retainer ...........................................................................1 ......................42881B ...........Snap Ring, KM171 Holds Race To Input Shaft (7/16”ID) 1983-88 ..................................................1 ......................42881C ...........Snap Ring, KM172/KM175/KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4AF3/........................A4BF1/A4BF2/F4A33/W4A32/W4A33 Holds Race To Input Shaft (3/4”ID) 1983-Up .....................1 ...................... 42885B ...........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.071”) 1983-89 ....1 ......................MD-70741342885BA .........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.079”) 1983-89 ....1 ......................MD-70740642885BB .........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.087”) 1983-89 ....1 ......................MD-70740742885BC.........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.094”) 1983-89 ....1 ......................MD-70740842885BD.........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.102”) 1983-89 ....1 ......................MD-70740942885BE .........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.110”) 1983-89 ....1 ......................MD-70741042885BG ........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.118”) 1983-89 ....1 ......................MD-70741142885BH.........Snap Ring, KM171/KM172/KM175 Holds Low/Reverse Top Pressure Plate In (.126”) 1983-89 ....1 ......................MD-70741242885E ...........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.071”) 1988-Up .1 ......................42885EA .........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.079”) 1988-Up .1 ......................42885EB .........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.087”) 1988-Up .1 ......................42885EC.........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.094”) 1988-Up .1 ......................42885ED.........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.102”) 1988-Up .1 ......................42885EE .........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.110”) 1988-Up .1 ......................42885EG ........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.118”) 1988-Up .1 ......................42885EH.........Snap Ring, All KM Except KM171/KM172/KM175 Low/Reverse Pressure Plate (.126”) 1988-Up .1 ......................42885M...........Snap Ring, F4A33/W4A33 Holds Low/Reverse Top Pressure Plate In (.115”) 1990-Up ................1 ......................42889B ...........Snap Ring, All KM With Ring Gear To Hub (.037”) 1983-Up ...........................................................1 ......................42889M...........Snap Ring, F4A33/W4A33 Holds Ring Gear To Hub (.060”) 1990-Up ............................................1 ......................42893B ...........Snap Ring, KM171/KM172/KM175 Holds Return Spring To Center Support ..................................1 ......................42893E ...........Snap Ring, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8 Holds Return Spring In ........................Center Support ................................................................................................................................1 ......................42894B ...........Snap Ring, KM171/KM171-5 Bearing To Case (2.710”ID) .060” ....................................................1 ......................42894C ...........Snap Ring, KM171/KM171-5 Bearing To Case (2.710”ID) .035” ....................................................1 ......................42894E ...........Snap Ring, KM172-5/KM175-5/KM176-5/KM177-8 Bearing To Case (3” ID) .................................1 ......................42894LC .........Snap Ring, A4AF1/A4AF2 Bearing To Case (.040” Thick)(3.884”OD) ............................................142894M...........Snap Ring, F4A33/W4A32/W4A33 Bearing To Case (3.650”ID) 1990-Up ......................................1 ......................42895B ...........Snap Ring, KM171/KM171-5 Bearing To Shaft (1.090”ID) ..............................................................1 ......................42895C ...........Snap Ring, KM172/KM175 Bearing To Shaft (1.300”ID) .................................................................1 ......................42895E ...........Snap Ring, KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2/W4A32/W4A33 ........................Bearing To Shaft (1.500”ID) 1990-Up ..............................................................................................1 ......................42896B ...........Snap Ring, KM171/KM172/KM175/KM172-5/KM176-5 Servo Cover (Top) ....................................1 ......................42896E ...........Snap Ring, KM175-5/KM177-8 Servo Cover (Top) .........................................................................1 ......................42896M...........Snap Ring, F4A33/W4A33 Servo Cover (Top) ................................................................................1 ......................42896N ...........Snap Ring, W4A32 Servo Cover (Top) Use 42869N ......................................................................1 ......................42897B ...........Snap Ring, KM171/KM172/KM171-5/KM172-5 Holds Governor To Transfer Shaft ........................1 ......................42898L ............Snap Ring, A4AF3/A4BF1/A4BF2 Pinion Bearing To Case (.099”Thick)(2 Eyelets) .......................142899B ...........Snap Ring, KM171/KM172/KM175/KM171-5/KM172-5 Holds Gear To Shaft .................................1 ......................42905B ...........Servo Assembly, KM171 (2.075”OD & 3.056”OD) Aluminum Cover 1983-88 .................................1 ......................42905C ...........Servo Assembly, KM175 (1.770”OD & 3.056”OD) Tin Cover 1985-89 ............................................1 ......................42905D ...........Servo Assembly, KM172/KM172-5 (1.955”OD & 3.056”OD) Aluminum Cover 1983-Up ................1 ......................42905E ...........Servo Assembly, KM175-5/KM177-8 (1.872”OD & 3.252”OD) 1988-Up (Plastic Cover ........................With 1 Wire Made To Cover) With Triangle Connection (With Adjustable Pin) ...............................1 ...................... 42905EA .........Servo Assembly, KM175-5/KM177-8 (1.872”OD & 3.252”OD) 1988-Up (Plastic Cover........................With 1 Wire Made To Cover) With Round Connector (With Adjustable Pin) ...................................1 ...................... 42905EB .........Servo Assembly, KM175-5/KM177-8 (1.872”OD & 3.252”OD) 1988-Up (Plastic Cover With........................Connector On Cover) No Wires (With Adjustable Pin) ....................................................................1 ......................42905H ...........ServoAssembly, KM171-5 (1.955”OD & 3.056”OD) Aluminum Cover 1989-Up ..............................1 ......................42905J ............Servo Assembly, KM176-5 (1.770”OD & 3.056”OD) 1989-Up (Plastic Cover ........................With 1 Prong Connector On Cover) No Wires (With Adjustable Pin) ..............................................1 ...................... 42905JA..........Servo Assembly, KM176-5 (1.770”OD & 3.056”OD) 1989-Up (Plastic Cover With 1 Wire........................Made To Cover) With Triangle Connector (With Adjustable Pin) .....................................................1 ......................42905L ............Servo Assembly, A4AF1/A4AF3 (1.770”OD & 3.056”OD) Plastic Cover With 1 Wire ........................Made To Cover (With 1 Prong Connector) Non Adjustable Pin .......................................................1 ...................... 42905LB .........Servo Assembly, A4BF1/A4BF2 (1.872”OD & 3.252”OD) Plastic Cover With 1 Wire ........................Made To Cover (With 1 Prong Connector) Non Adjustable Pin .......................................................1 ...................... 42905M...........Servo Assembly, F4A33/W4A33 (2.225”OD & 3.925”OD) Plastic Cover 1990-Up .........................1 ......................42905N ...........Servo Assembly, W4A32 (2.041”OD & 3.575”OD) Plastic Cover 1991-Up .....................................1 ......................

7.3t

MIT

SU

BIS

HI



42960C ...........Piston, KM175 Overdrive Clutch 1985-89 .......................................................................................1 ......................42960E ...........Piston, KM175-5/KM176-5 Overdrive Clutch 1988-Up ...................................................................1 ......................42960G ...........Piston, KM177-8/A4BF1/A4BF2 Overdrive Clutch (Steel) 1988-Up ...............................................1 ......................42960LB .........Piston, A4AF3 Overdrive Clutch (Aluminum) ..................................................................................1 ......................42960M...........Piston, F4A33/W4A32/W4A33 Overdrive 1990-Up .........................................................................1 ......................42967B ...........Piston, KM171 Low/Reverse Clutch 1983-88 .................................................................................1 ......................42967C ...........Piston, KM172/KM175 Low/Reverse Clutch 1983-89 .....................................................................1 ......................42967E ...........Piston, KM172-5/KM175-5/KM177-8/A4BF1/A4BF2/W4A32 Low/Reverse Clutch 1988-Up ..........1 ......................42967H ...........Piston, KM171-5/KM176-5/A4AF1/A4AF3/F4A32 Low/Reverse Clutch 1989-Up ..........................1 ......................42967M...........Piston, F4A33/W4A33 Low/Reverse Clutch 1990-Up .....................................................................1 ......................42970C ...........Spring, KM175 Overdrive Clutch Return 1985-89 ...........................................................................1 ......................42970E ...........Spring, KM175-5/KM176-5 Overdrive Clutch Return 1988-Up .......................................................1 ......................42970G ...........Spring, KM177-8/A4BF1/A4BF2 Overdrive Clutch Return 1989-Up ...............................................1 ......................42970LB .........Springs W/Retainer, A4AF3 Overdrive Clutch Return (16 Springs) ................................................1 ......................42970M...........Spring, F4A33/W4A32/W4A33 Overdrive Clutch Return 1990-Up .................................................1 ......................42974B ...........Return Spring, KM171/KM172 Forward Clutch 1983-88 .................................................................1 ......................42974C ...........Return Spring, KM175 Forward Clutch 1985-89 .............................................................................1 ......................42974E ...........Return Spring, KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/W4A32 Forward Clutch 1988-Up .....1 ......................42974H ...........Return Spring, KM171-5/KM172-5 Forward Clutch 1989-Up ..........................................................1 ......................42974L ............Return Spring, A4AF3 Forward Clutch (19 Coil Springs) ................................................................1 ......................42974M...........Return Spring, F4A33/W4A33 Forward Clutch 1990-Up ................................................................1 ......................42975B ...........Return Spring, KM171/KM172/KM175 Direct Clutch (1 Coil Spring) 1983-89 ................................1 ......................42975E ...........Return Spring Set, KM171-5/KM172-5/KM175-5/KM176-5/KM177-8/A4AF1/A4BF1/A4BF2W4A32........................Direct Clutch (23 Coil Springs)(2.448”ID) 1988-Up .........................................................................1 ...................... 42975L ............Return Spring Set, A4AF3 Direct Clutch (23 Coil Springs)(2.535”ID) .............................................1 ......................42975M...........Return Spring Set, F4A33/W4A33 Direct Clutch (23 Coil Springs) 1992-Up ..................................1 ......................42977M...........Cushion, F4A33/W4A33 Low/Reverse Clutch (6 3/8”OD) ..............................................................1 ......................42991E ...........Linkage Assembly, KM175-5/KM176-5 Internal (.130” Thick Rooster Comb) .................................1 ......................42991EA .........Linkage Assembly, KM175-5/KM176-5 Internal (.175” Thick Rooster Comb) .................................1 ......................42991G ...........Linkage Assembly, KM177-8 Internal 1989-Up ...............................................................................1 ......................42991L ............Linkage Assembly, A4AF1/A4AF3/A4BF1/A4BF2 Internal ..............................................................1 ......................42994B ...........Park Actuator Rod, KM170/KM171/KM172/KM175/KM177/KM171-5/KM172-5/KM175-5/KM176-5......................../KM177-8 (5 7/8” Long) ...................................................................................................................1 ......................42994L ............Park Actuator Rod, A4AF1/A4AF3/A4BF1/A4BF2 (6 1/4” Long) .....................................................1 ......................42994M...........Park Actuator Rod, F4A33/W4A32/W4A33 (With 2 Rollers) 1990-Up ............................................1 ......................


7.3u

MITS

UB

ISH

I



Subject:Flare on 2-3 shift

Unit:Hyundai KM series

Essential Reading:

Rebuilder

Diagnostician

R & R (Installers)

Shop Owner

Center Manager

Author:Pete Luban, ATSGTransmission DigestContributing Editor

Temp-eramental

Hyundai

I was handling a call on the ATSG Tech Line about a2000 Hyundai Elantra that had a complaint of a �areon the

2-3 shift. Ordinarily, a KM unit with a 2-3 �are could have a

problem with servo-release pressure, usually caused bythe computer not shutting o� the pressure-control sole-noid quickly enough. There could be a problem with theservo switch if it were stuck. In other words, these are theusual components that could cause a 2-3 �are on a KMunit.

In this situation it was none of the usual items. It was,believe it or not, the transmission-�uid-temperature sen-sor. As I looked further into this, sure enough, I foundfactory bulletin 00-40-010 dated August 2000.

It seems that this vehicle had stored a P0712 for ashorted ATF-temp sensor, which causes the TCM to cre-ate a �ared 2-3 shift in this vehicle model. Computerstrategy seems to be the culprit here.

As I read the bulletin, I found other unusual computerstrategies in play on various Hyundai model years, all re-lated to the ATF-temp sensor and in what manner itfailed.

If the ATF-temp sensor fails open and stores codeP0713, the complaint would be a harsh garage shift frompark to either drive or reverse and no converter-clutchapplication.

If the vehicle were a 1996-2000 Elantra or Tiburon, or a1995-2001 Accent, the complaint would be no 4th gear.

If this were a 1999-2001 Sonata, the complaint wouldbe no upshift past 2nd gear.

Should the ATF-temp sensor become shorted and aP0712 be stored, the 2-3 �ared-shift complaint would af-fect 1996-2000 Elantra and Tiburon as well as 1995-2001Accent.

In the event this happens to you, the part number ofthe ATF-temp sensor for the 1996-2000 Elantra andTiburon and for the 1995-2001 Accent is 46386-22600.

The part number for the 1999-2001 Sonata is 46386-39050. TD

Shift Pointers

©2006 Transmission Digest

TD 04_06 Shift Pointers_lay 8/29/06 10:25 AM Page 10

Hyundai / Mitsubishi FWD Transmission I.D. Chart · 2018. 10. 8. · KM177 2 Piece 4 Spd L/Up Cast...

Documents

Transcript of Hyundai / Mitsubishi FWD Transmission I.D. Chart · 2018. 10. 8. · KM177 2 Piece 4 Spd L/Up Cast...