HYGIENISK - ikea.com

HYGIENISKGB

ENGLISHPlease refer to the last page of this manual for the full list ofIKEA appointed After Sales Service Provider and relativenational phone numbers.

ENGLISH 4

ContentsSafety information 4Safety instructions 6Product description 7Control panel 8Programme selection 9Basic settings 12Before first use 16Daily use 18

Hints and tips 20Care and cleaning 22Troubleshooting 25Technical information 30Environmental concerns 31IKEA guarantee 31

Subject to change without notice.

Safety information

Before the installation and use of the appliance, carefully readthe supplied instructions. The manufacturer is not responsiblefor any injuries or damage that are the result of incorrectinstallation or usage. Always keep the instructions in a safeand accessible location for future reference.

Children and vulnerable people safety• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory ormental capabilities or lack of experience and knowledge ifthey have been given supervision or instruction concerningthe use of the appliance in a safe way and understand thehazards involved.

• Children between 3 and 8 years of age and persons withvery extensive and complex disabilities shall be kept awayfrom the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept awayfrom the appliance unless continuously supervised.

• Do not let children play with the appliance.• Keep detergents away from children.• Keep children and pets away from the appliance when the

door is open.

ENGLISH 4

• Children shall not carry out cleaning and user maintenanceof the appliance without supervision.

General Safety• This appliance is intended to be used in household and

similar applications such as:– farm houses; staff kitchen areas in shops, offices and

other working environments;– by clients in hotels, motels, bed & breakfast and other

residential type environments.• Do not change the specification of this appliance.• The operating water pressure (minimum and maximum)

must be between 0.5 (0.05) / 8 (0.8) bar (MPa)• Follow the maximum number of 14 place settings.• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarlyqualified persons in order to avoid a hazard.

• Put the cutlery in the cutlery basket with the sharp endspointing down or put them in the cutlery drawer in ahorizontal position with the sharp edges down.

• Do not leave the appliance with the open door unattendedto avoid stepping accidentally onto it.

• Before any maintenance operation, deactivate the applianceand disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam toclean the appliance.

• If the appliance has ventilation openings in the base, theymust not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains usingthe new supplied hose-sets. Old hose sets must not bereused.

ENGLISH 5

Safety instructions

Installation

Warning! Only a qualified personmust install this appliance.

• Remove all the packaging.• Do not install or use a damaged

appliance.• Do not use the appliance before installing

it in the built-in structure due to safetymanner.

• Follow the installation instructionssupplied with the appliance.

• Always take care when moving theappliance as it is heavy. Always use safetygloves and enclosed footwear.

• Do not install or use the appliance wherethe temperature is less than 0 °C.

• Install the appliance in a safe and suitableplace that meets installationrequirements.

Electrical connection

Warning! Risk of fire and electricshock.

• The appliance must be earthed.• Make sure that the parameters on the

rating plate are compatible with theelectrical ratings of the mains powersupply.

• Always use a correctly installedshockproof socket.

• Do not use multi-plug adapters andextension cables.

• Make sure not to cause damage to themains plug and to the mains cable.Should the mains cable need to bereplaced, this must be carried out by ourAuthorised Service Centre.

• Connect the mains plug to the mainssocket only at the end of the installation.Make sure that there is access to themains plug after the installation.

• Do not pull the mains cable to disconnectthe appliance. Always pull the mains plug.

• This appliance is fitted with a 13 A mainsplug. If it is necessary to change the

mains plug fuse, use only a 13 A ASTA (BS1362) fuse (UK and Ireland only).

Water connection• Do not cause damage to the water hoses.• Before connection to new pipes, pipes not

used for a long time, where repair workhas been carried out or new devices fitted(water meters, etc.), let the water flowuntil it is clean and clear.

• Ensure that there are no visible waterleaks during and after the first use of theappliance.

• The water inlet hose has a safety valveand a sheath with an inner mains cable.

Warning! Dangerous voltage.

• If the water inlet hose is damaged,immediately close the water tap anddisconnect the mains plug from themains socket. Contact the AuthorisedService Centre to replace the water inlethose.

Use• Do not put flammable products or items

that are wet with flammable products in,near or on the appliance.

• Dishwasher detergents are dangerous.Follow the safety instructions on thedetergent packaging.

• Do not drink and play with the water inthe appliance.

• Do not remove the dishes from theappliance until the programme is

ENGLISH 6

complete. Some detergent may remainon the dishes.

• Do not store items or apply pressure onthe open door of the appliance.

• The appliance can release hot steam ifyou open the door while a programmeoperates.

Internal lighting

Warning! Risk of injury.

• Concerning the lamp(s) inside thisproduct and spare part lamps soldseparately: These lamps are intended towithstand extreme physical conditions inhousehold appliances, such astemperature, vibration, humidity, or areintended to signal information about theoperational status of the appliance. Theyare not intended to be used in otherapplications and are not suitable forhousehold room illumination.

• To replace the internal lighting, contactthe Authorised Service Centre.

Service• To repair the appliance contact the

Authorised Service Centre. Use originalspare parts only.

• Please note that self-repair or non-professional repair can have safetyconsequences and might void theguarantee.

• The following spare parts will be availablefor 7 years after the model has beendiscontinued: motor, circulation and drainpump, heaters and heating elements,including heat pumps, piping and relatedequipment including hoses, valves, filtersand aquastops, structural and interiorparts related to door assemblies, printedcircuit boards, electronic displays,pressure switches, thermostats andsensors, software and firmware includingreset software. Please note that some ofthese spare parts are only available toprofessional repairers, and that not allspare parts are relevant for all models.

• The following spare parts will be availablefor 10 years after the model has beendiscontinued: door hinge and seals, otherseals, spray arms, drain filters, interiorracks and plastic peripherals such asbaskets and lids.

Disposal

Warning! Risk of injury orsuffocation.

• Disconnect the appliance from the mainssupply.

• Cut off the mains cable and discard it.• Remove the door catch to prevent

children and pets to get closed in theappliance.

Product description

The graphics below is just ageneral product overview. Formore detailed information pleaserefer to other chapters and/ordocuments provided with theappliance.

ENGLISH 7

10

11

9

2

1

4

3

5678

1 Ceiling spray arm

2 Lower spray arm

3 Filters

4 Rating plate

5 Salt container

6 Rinse aid dispenser

7 Detergent dispenser

8 Lower basket

9 Upper spray arm

10 Upper basket

11 Cutlery drawer

Control panel

1 3 4 5 62

1 On/Off button / Reset button

2 Delay start button

3 Display

4 Programme buttons

5 Option buttons

6 AUTO programme button

ENGLISH 8

Display

A AB

A. IndicatorsB. Time indicator

Indicators

Indicator DescriptionRinse aid indicator. It is on when the rinse aid dispenser needs refilling. Re‐fer to "Before first use".

Salt indicator. It is on when the salt container needs refilling. Refer to "Be‐fore first use".

Machine Care indicator. It is on when the appliance needs internal cleaningwith the Machine Care programme. Refer to "Care and cleaning".

Drying phase indicator. It is on when a programme with the drying phase isselected. It flashes when the drying phase operates. Refer to "Programmeselection".

Programme selection

Programmes

A B C D E

A. • Quick 30' is the shortest programmesuitable for washing a load with freshand light soil.

• Rinse & Hold is a programme forrinsing off food remains from thedishes. It prevents odours forming inthe appliance. Do not use detergentwith this programme.

B. 60 Minutes is a programme suitable forwashing a load with fresh and lightlydried-on soil.

C. 90 Minutes is a programme suitable forwashing and drying normally soileditems.

D. Intensive is a programme suitable forwashing and drying heavily soiled items.

E. ECO is the longest programme offeringthe most efficient use of energy and

ENGLISH 9

water consumption for crockery andcutlery with normal soil. This is thestandard programme for testinstitutes. 1)

OptionsYou can adjust the programme selection toyour needs by activating options.

Power Clean

Power Clean improves the washingresults of the selected programme. Theoption increases the wash temperature andduration.

Gentle / Glass

Gentle / Glass provides special care for adelicate load. The option prevents rapid

changes in the wash temperature of theselected programme and reduces it to 45 °C.This protects glassware in particular fromdamaging.

AUTOThe AUTO program automatically adjusts thewash cycle to the type of load.

The appliance senses the degree of soil andthe amount of dishes in the baskets. Itadjusts the temperature and quantity ofwater as well as the wash duration.

Programs overview

Programme Type of load Degree of soil Programme phases Options• Crockery• Cutlery

• Fresh • Wash 50 °C• Intermediate rinse• Final rinse 45 °C• AutoOpen

••

• All types ofloads

• All degreesof soil

• Prewash Options are not ap‐plicable to this pro‐gramme.

• Crockery• Cutlery

• Fresh• Lightly

dried-on

• Wash 60 °C• Intermediate rinse• Final rinse 50 °C• AutoOpen

••

• Crockery• Cutlery• Pots• Pans

• Normal• Lightly

dried-on

• Wash 60 °C• Intermediate rinse• Final rinse 55 °C• Drying• AutoOpen

••

1) This programme is used to assess compliance with the Ecodesign Comission Regulation (EU) 2019/2022.

ENGLISH 10

Programme Type of load Degree of soil Programme phases Options• Crockery• Cutlery• Pots• Pans

• Normal toheavy

• Dried-on

• Prewash• Wash 60 °C• Intermediate rinse• Final rinse 60 °C• Drying• AutoOpen

••


• Normal• Lightly

dried-on

• Prewash• Wash 50 °C• Intermediate rinse• Final rinse 55 °C• Drying• AutoOpen

••


The pro‐gramme ad‐justs to all de‐grees of soil.

• Prewash• Wash 50 - 60 °C• Intermediate rinse• Final rinse 60 °C• Drying• AutoOpen

Options are not ap‐plicable to this pro‐gramme.

MachineCare

• No load The pro‐grammecleans the ap‐pliance interi‐or.Refer to "Careand clean‐ing".

• Wash 70 °C• Intermediate rinse• Final rinse• AutoOpen

Options are not ap‐plicable to this pro‐gramme.

Consumption values

Programme 1) 2) Water (l) Energy (kWh) Duration (min)

9.9 -12.1 0.56 - 0.69 30

4.1 - 5.0 0.01 - 0.04 15

10.4 - 12.7 0.83 - 0.96 60

10.3 - 12.6 0.96 - 1.09 90

9.8 - 12.0 1.05 - 1.18 160

10.53) / 10.54) / 11.35) 0.8323) / 0.8484) /0.8485)

2403) / 2404) / 2405)

ENGLISH 11

Programme 1) 2) Water (l) Energy (kWh) Duration (min)

8.7 - 12.0 0.75 - 1.18 120 - 170

Machine Care 8.9 - 10.9 0.60 - 0.72 601) The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity ofdishes and the degree of soil can change the values.2) The values for programmes other than ECO are indicative only.3) In accordance with the 1016/2010 regulation.4) In accordance with the 2019/2022 regulation.5) In accordance with UAE.S5010-6:2019 regulation.

Information for test institutesTo receive the necessary information forconducting performance tests (e.g.according to EN60436), send an email to:

[email protected]

In your request, include the product numbercode (PNC) from the rating plate.

For any other questions regarding yourdishwasher, refer to the service bookprovided with your appliance.

Basic settings

You can configure the appliance by changingbasic settings according to your needs.

Number Setting Values Description1)

1 Water hardness From level 1L tolevel 10L

Adjust the level of the water softener ac‐cording to the water hardness in your area.Factory setting: 5L.

2 Rinse aid emptynotification

1d (on)0d (off)

Activate or deactivate the rinse aid indica‐tor.Factory setting: 1d.

3 End sound 1b (on)0b (off)

Activate or deactivate the acoustic signal forthe end of a programme.Factory setting: 0b.

4 Auto door open 1o (on)0o (off)

Activate or deactivate the AutoOpen.Factory setting: 1o.

5 Key tones 1F (on)0F (off)

Activate or deactivate the sound of the but‐tons when pressed.Factory setting: 1F.

ENGLISH 12

Number Setting Values Description1)

6 Latest pro‐gramme selec‐tion

1H (on)0H (off)

Enable or disable the automatic selection ofthe most recently used programme and op‐tions.Factory setting: 0H.

7 Display on floor 1C (on)0C (off)

Activate or deactivate the TimeBeam.Factory setting: 1C.

1) For more details, refer to the information provided in this chapter.

You can change the basic settings in settingmode. Instructions on how to configure theappliance are provided further in thischapter.

When the appliance is in setting mode, thedisplay shows a digit and a letter. For eachsetting, a dedicated letter is displayed. Thededicated letters are indicated in the table.

The order of the basic settings presented inthe table is also the order of the settings insetting mode.

The water softenerThe water softener removes minerals fromthe water supply, which would have a

negative effect on the washing results andon the appliance.

The higher the content of these minerals,the harder your water is. Water hardness ismeasured in equivalent scales.

The water softener should be adjustedaccording to the hardness of the water inyour area. Your local water authority canadvise you on the hardness of the water inyour area. It is important to set the rightlevel of the water softener to assure goodwashing results.

Water hardnessGerman degrees

(°dH)French degrees

(°fH)mmol/l Clarke de‐

greesWater softener level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27 5 1)

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

ENGLISH 13

German degrees(°dH)

French degrees(°fH)

mmol/l Clarke de‐grees

Water softener level

<4 <7 <0.7 < 5 1 2)

1) Factory setting.2) Do not use salt at this level.

Regardless of the type of detergent used,set the proper water hardness level tokeep the salt refill indicator active.

Multi-tabs containing salt are noteffective enough to soften hardwater.

Regeneration process

For the correct water softener operation, theresin of the softener device needs to beregenerated regularly. This process isautomatic and is the part of the normaldishwasher operation.

When the prescribed quantity of water (seevalues in the table) has been used since theprevious regeneration process, a newregeneration process will be initiatedbetween the final rinse and the programmeend.

Water softener level Amount of water (l)1 250

2 100

3 62

4 47

5 25

6 17

7 10

8 5

9 3

10 3

In case of the high water softener setting, itmay occur also in the middle of theprogramme, before the rinse (twice during a

programme). Regeneration initiation has noimpact on the cycle duration, unless it occursin the middle of a programme or at the endof a programme with a short drying phase.In that cases, the regeneration prolongs thetotal duration of a programme by additional5 minutes.

Subsequently, the rinsing of the watersoftener that lasts 5 minutes may begin inthe same cycle or at the beginning of thenext programme. This activity increases thetotal water consumption of a programme byadditional 4 litres and the total energyconsumption of a programme by additional2 Wh. The rinsing of the softener ends with acomplete drain.

Each performed softener rinse (possiblemore than one in the same cycle) mayprolong the programme duration by another5 minutes when it occurs at any point at thebeginning or in the middle of a programme.

All the consumption valuesmentioned in this section aredetermined in accordance withthe currently applicable standardin laboratory conditions withwater hardness 2.5mmol/Laccording to the 2019/2022regulation (water softener: level3).The pressure and thetemperature of water as well asthe variations of the mains supplycan change the values.

The rinse aid empty notificationThe rinse aid helps to dry the dishes withoutstreaks and stains. It is automaticallyreleased during the hot rinse phase.

ENGLISH 14

When the rinse aid chamber is empty, therinse aid indicator is turned on notifying torefill rinse aid. If the drying results aresatisfactory while using multi-tablets only, itis possible to deactivate the notification forrefilling rinse aid. However, for best dryingperformance, always use rinse aid.

If standard detergent or multi-tabletswithout rinse aid are used, activate thenotification to keep the rinse aid refillindicator active.

End soundYou can activate an acoustic signal thatsounds when the programme is completed.

Acoustic signals sound also whena malfunction of the applianceoccurs. It is not possible todeactivate these signals.

AutoOpenAutoOpen improves the drying results withless energy consumption. The appliancedoor opens automatically during the dryingphase and remains ajar.

AutoOpen is automatically activated with allprogrammes other than Rinse & Hold.

Caution! Do not try to close theappliance door within 2 minutesafter automatic opening. This cancause damage to the appliance.

Caution! If children, pets orpeople with disabilities haveaccess to the appliance,deactivate AutoOpen. Theautomatic opening of the doormay pose a danger and exposepossible hazards inside theappliance (such as knives, sharpobjects, chemicals).

Key tonesThe buttons on the control panel make aclick sound when you press them. You candeactivate this sound.

Latest programme selectionYou can set the automatic selection of themost recently used programme and options.

The latest programme that was completedbefore the appliance deactivation is saved. Itis then selected automatically after youactivate the appliance.

When the latest programme selection isdisabled, the default programme is ECO.

TimeBeam

TimeBeam displays the followinginformation on the floor below the appliancedoor:• The programme duration when the

programme begins.• 0:00 and CLEAN when the programme is

complete.

ENGLISH 15

• DELAY and the countdown duration whenthe delay start begins.

• An alarm code when the appliance has amalfunction.

When AutoOpen opens the door,TimeBeam is off. To check theremaining time of the runningprogramme, look at the controlpanel display.

Setting mode

How to enter setting modeYou can enter setting mode before starting aprogramme. You cannot enter setting modewhile the programme is running.

To enter setting mode, press and holdsimultaneously and for about 3seconds.

• The lights related to , and are on.

• The display shows the current valueof the first available setting.

How to navigate in setting modeYou can navigate in setting mode usingprogramme buttons.

A B C

A. Previous buttonB. OK buttonC. Next buttonUse Previous and Next to switch betweenthe basic settings and to change their value.

Use OK to enter the selected setting and toconfirm changing its value.

How to change a settingMake sure the appliance is in setting mode.

1. Use Previous or Next to select thedesired setting.

The display shows the current setting value(a digit and the dedicated letter).2. Press OK to enter the setting.The current setting value flashes.3. Press Previous or Next to change the

value.4. Press OK to confirm the setting.

• The new setting is saved.• The appliance returns to the basic

settings list.5. Press and hold simultaneously and

for about 3 seconds to exitsetting mode.

The appliance returns to the programmeselection.The saved settings remain valid until youchange them again.

Before first use

1. Make sure that the current level of thewater softener agrees with thehardness of the water supply. If not,adjust the level of the water softener.

2. Fill the salt container.3. Fill the rinse aid dispenser.

4. Open the water tap.5. Start the programme Quick 30' to

remove any residuals from themanufacturing process. Do not usedetergent and do not put dishes in thebaskets.

ENGLISH 16

After starting the programme, the appliancerecharges the resin in the water softener forup to 5 minutes. The washing phase startsonly after this procedure is complete. Theprocedure is repeated periodically.

The salt container

Caution! Use rough salt designedfor dishwashers only. Fine saltincreases the risk of corrosion.

The salt is used to recharge the resin in thewater softener and to assure good washingresults in daily use.

Filling the salt container

1 2

3

Put 1 litre of water inthe salt container(only for the firsttime).

4

Put 1 kg of salt in thesalt container.

5

Turn the cap of thesalt containerclockwise to closethe salt container.

Caution! Water and salt maycome out of the salt containerwhen you fill it. After you fill thesalt container, immediately start aprogramme to prevent corrosion.

Filling the rinse aid dispenser

1 2

3

max

4

ENGLISH 17

5

M A X

4 3 2 1

To adjust thereleased quantity ofrinse aid, turn theselector betweenposition 1 (lowestquantity) andposition 4 (highestquantity).

Daily use

1. Open the water tap.2. Press and hold until the appliance is

activated.3. Fill the salt container if it is empty.4. Fill the rinse aid dispenser if it is empty.5. Load the baskets.6. Add the detergent.7. Select and start a programme.8. Close the water tap when the

programme is complete.Using the detergent

1 2

3

A

Put the detergent orthe multi-tablet incompartment (A).

4

If the programme has a prewash phase, puta small quantity of detergent on the innerpart of the appliance door.

ENGLISH 18

When you use multi-tablets that contain saltand rinse aid, it is not necessary to fill thesalt container and the rinse aid dispenser.• Adjust the water softener to the lowest

level.• Set the rinse aid dispenser to the lowest

position.Multi-tabs containing salt are noteffective enough to soften hardwater.

How to select and start a programme1. Press the button dedicated to the

programme you want to set.• The light related to the button is on.• The display shows the programme

duration.2. Activate applicable options if desired.3. Close the appliance door to start the

programme.

How to select and start theprogramme

1. To select , press and hold for 3seconds.• The light related to the button is on.• The display shows the programme

duration.Options are not applicable to thisprogramme.

2. Close the appliance door to start theprogramme.

How to activate options1. Select a programme.2. Press the button dedicated to the option

you want to activate.• The light related to the button is on.• The display shows the updated

programme duration.

By default, options must beactivated every time before youstart a programme.If the latest programme selectionis enabled, the saved options areactivated automatically along withthe programme.

It is not possible to activate ordeactivate options while aprogramme is running.

Not all options are compatiblewith each other.

Activating options often increasesthe water and energyconsumption as well as theprogramme duration.

How to select and start theprogramme AUTO

1. Press .• The light related to the button is on.• The display shows the programme

duration.Options are not applicable to thisprogramme.

2. Close the appliance door to start theprogramme.

The appliance senses the type of load andadjusts a suitable wash cycle. During thecycle, the sensors operate several times andthe initial programme duration candecrease.

How to delay the start of aprogramme1. Select a programme.2. Press repeatedly until the display

shows the desired delay time (from 1 to24 hours).

The light related to the button is on.3. Close the appliance door to start the

countdown.

ENGLISH 19

During the countdown, it is not possible tochange the delay time and the programmeselection.

When the countdown is complete, theprogramme starts.

How to cancel the delay start whilethe countdown operates

Press and hold for about 3 seconds.The appliance returns to the programmeselection.

If you cancel the delay start, youhave to select the programmeagain.

How to cancel a running programme

Press and hold for about 3 seconds.The appliance returns to the programmeselection.

Make sure that there is detergentin the detergent dispenser beforeyou start a new programme.

Opening the door while theappliance operatesOpening the door while a programme isrunning stops the appliance. It may affect

the energy consumption and theprogramme duration. After closing the door,the appliance continues from the point ofinterruption.

If the door is opened for morethan 30 seconds during thedrying phase, the runningprogramme ends. It does nothappen if the door is opened byAutoOpen function.

The Auto Off functionThis function saves energy by switching theappliance off when it is not operating.

The function activates automatically:• After up to 15 seconds once the

programme is complete.• After 5 minutes if a programme was not

started.

End of the programmeWhen the programme is complete, thedisplay shows 0:00.

The Auto Off function switches the applianceoff automatically.

All buttons are inactive except for the on/offbutton.

Hints and tips

GeneralFollow the hints below to ensure optimalcleaning and drying results in daily use andto protect the environment.

• Washing dishes in the dishwasher asinstructed in the user manual usuallyconsumes less water and energy thanwashing dishes by hand.

• Load the dishwasher to its full capacity tosave water and energy. For best cleaningresults, arrange items in the baskets asinstructed in the user manual and do notoverload the baskets.

• Do not pre-rinse dishes by hand. Itincreases the water and energyconsumption. When needed, select aprogramme with a prewash phase.

• Remove larger residues of food from thedishes and empty cups and glassesbefore putting them inside the appliance.

• Soak or slightly scour cookware withfirmly cooked-on or baked-on food beforewashing it in the appliance.

• Make sure that items in the baskets donot touch or cover each other. Only thencan the water completely reach and washthe dishes.

ENGLISH 20

• You can use dishwasher detergent, rinseaid and salt separately or you can use themulti-tablets (e.g. ''All in 1''). Follow theinstructions on the packaging.

• Select a programme according to the typeof load and the degree of soil. ECO offersthe most efficient use of water andenergy consumption.

• To prevent limescale buildup inside theappliance:– Refill the salt container whenever

necessary.– Use the recommended dosage of the

detergent and rinse aid.– Make sure that the current level of

the water softener agrees with thehardness of the water supply.

– Follow the instructions in the chapter "Care and cleaning".

Using salt, rinse aid and detergent• Only use salt, rinse aid and detergent

designed for dishwasher. Other productscan cause damage to the appliance.

• In areas with hard and very hard water,we recommend to use basic dishwasherdetergent (powder, gel, tablets containingno additional agents), rinse aid and saltseparately for optimal cleaning anddrying results.

• Detergent tablets do not fully dissolvewith short programmes. To preventdetergent residues on the tableware, werecommend that you use tablets withlong programmes.

• Always use the correct quantity ofdetergent. Insufficient dosage ofdetergent can result in poor cleaningresults and hard-water filming or spottingon the items. Using too much detergentwith soft or softened water results indetergent residues on the dishes. Adjustthe amount of detergent based on thewater hardness. Refer to the instructionson the detergent packaging.

• Always use the correct quantity of rinseaid. Insufficient dosage of rinse aiddecreases the drying results. Using toomuch rinse aid results in bluish layers onthe items.

• Make sure that the water softener level iscorrect. If the level is too high, theincreased quantity of salt in the watermight result in rust on cutlery.

What to do if you want to stop usingmulti-tabletsBefore you start using separately detergent,salt and rinse aid, complete the followingsteps:

1. Set the highest level of the watersoftener.

2. Make sure that the salt and rinse aidcontainers are full.

3. Start the Quick 30' programme. Do notadd detergent and do not put dishes inthe baskets.

4. When the programme is completed,adjust the water softener according tothe water hardness in your area.

5. Adjust the released quantity of rinse aid.

Before starting a programmeBefore you start the selected programme,make sure that:

• The filters are clean and correctlyinstalled.

• The cap of the salt container is tight.• The spray arms are not clogged.• There is enough salt and rinse aid (unless

you use multi-tablets).• The arrangement of the items in the

baskets is correct.• The programme is suitable to the type of

load and the degree of soil.• The correct quantity of detergent is used.

Loading the baskets

Refer to the supplied leaflet withexamples of the load of thebaskets.

• Always use the whole space of thebaskets.

• Use the appliance to wash dishwasher-safe items only.

ENGLISH 21

• Do not wash in the appliance items madeof wood, horn, aluminium, pewter andcopper as they could crack, warp, getdiscoloured or pitted.

• Do not wash in the appliance items thatcan absorb water (sponges, householdcloths).

• Remove remaining food from the items.• Soak cookware with burnt-on food before

washing it in the appliance.• Put hollow items (cups, glasses and pans)

with the opening facing downwards.• Make sure that cutlery and dishes do not

bond together. Mix spoons with othercutlery.

• Make sure that glasses do not touch eachother.

• Put cutlery and small items in the cutlerydrawer .

• Put light items in the upper basket. Makesure that the items do not move freely.

• Make sure that the spray arm can movefreely before you start a programme.

Unloading the baskets1. Let the tableware cool down before you

remove it from the appliance. Hot itemscan be easily damaged.

2. First remove items from the lowerbasket, then from the upper basket.

After the programme iscompleted, water can still remainon the inside surfaces of theappliance.

Care and cleaning

Warning! Before anymaintenance other than runningthe programme Machine Care,deactivate the appliance anddisconnect the mains plug fromthe main socket.

Dirty filters and clogged sprayarms negatively affect thewashing results. Check theseelements regularly and, ifnecessary, clean them.

Machine CareMachine Care is a programme designed toclean the appliance interior with optimalresults. It removes limescale and greasebuildup.

When the appliance senses the need forcleaning, the indicator is on. Start theMachine Care programme to clean theappliance interior.

How to start the Machine Careprogramme

Before starting the Machine Careprogramme, clean the filters andspray arms.

1. Use a descaler or a cleaning productdesigned specifically for dishwashers.Follow the instructions on the packaging.Do not put dishes in the baskets.

2. Press and hold simultaneously and for about 3 seconds.

The indicators and flash. The displayshows the programme duration.3. Close the appliance door to start the

programme.When the programme is complete, theindicator is off.

Internal cleaning• Carefully clean the appliance, including

the rubber gasket of the door, with a softdamp cloth.

ENGLISH 22

• Do not use abrasive products, abrasivecleaning pads, sharp tools, strongchemicals, scourer or solvents.

• To maintain the performance of yourappliance, use a cleaning productdesigned specifically for dishwashers atleast once every two months. Carefullyfollow the instructions on the packagingof the product.

• For optimal cleaning results, start theMachine Care programme.

Removal of foreign objectsCheck the filters and the sump after eachuse of the dishwasher. Foreign objects (e.g.pieces of glass, plastic, bones or toothpicks,etc) decrease the cleaning performance andcan cause damage to the drain pump.

Caution! If unable to remove theforeign objects, contact anAuthorised Service Centre.

1. Disassemble the filters system asinstructed in this chapter.

2. Remove any foreign objects manually.3. Reassemble the filters as instructed in

this chapter.

External cleaning• Clean the appliance with a moist soft

cloth.• Only use neutral detergents.• Do not use abrasive products, abrasive

cleaning pads or solvents.

Cleaning the filters

1

Make sure that thereare no residues offood or soil in oraround the edge ofthe sump.

2

C

B

A

The filter system ismade of three parts.

3

To remove filters (B)and (C), turn thehandlecounterclockwiseand pull it upwards.Remove the filter (C)out of filter (B).Wash the filters withwater.

4

Remove the flat filter(A). Wash the filterwith water.

ENGLISH 23

5

D

Put the flat filter (A)back in place. Makesure that it iscorrectly positionedunder the 2 guides(D).

6

Reassemble thefilters (B) and (C). Putthem back in thefilter (A). Turn thehandle clockwiseuntil it locks.

An incorrect position of the filterscan cause bad washing resultsand damage to the appliance

Cleaning the filter of the inlet hose

1

Close the water tap.

2

A

Disconnect the hose.Turn the fastener Aclockwise.

3

Clean the filter ofthe inlet hose.

4

Cleaning the lower spray armWe recommend to clean the lower spray armregularly to prevent soil from clogging theholes. Clogged holes can causeunsatisfactory washing results.

1

To remove the lowerspray arm, pull itupwards.

2

Wash the spray armunder runningwater. Use a thinpointed tool, e.g. atoothpick, to removeparticles of soil fromthe holes.

3

To install the sprayarm back, press itdownwards.

Cleaning the ceiling spray armWe recommend to clean the ceiling sprayarm regularly to prevent soil from cloggingthe holes. Clogged holes can causeunsatisfactory washing results.

ENGLISH 24

1

The ceiling sprayarm is placed on theceiling of theappliance.

2

1

2

Release the stopperson the sides of thesliding rails of thecutlery drawer andpull the drawer out.

3

1

2

Move the upperbasket to the lowestlevel to reach thespray arm moreeasily.

4

C

B

A

The spray arm (C) isinstalled in thedelivery tube (A)with the mountingelement (B).

5

Turn the mountingelementcounterclockwiseand pull the sprayarm downwards.

6

Wash the spray armunder runningwater. Use a thinpointed tool, e.g. atoothpick, to removeparticles of soil fromthe holes. Run thewater through theholes to wash soilparticles away fromthe inside.

7

Insert the mountingelement in the sprayarm and fix it in thedelivery tube byturning it clockwise.Make sure themounting elementlocks into place.

8

1

2

Install the cutlerydrawer on thesliding rails andblock the stoppers.

Troubleshooting

Warning! Improper repair of theappliance may pose a danger tothe safety of the user. Any repairsmust be performed by qualifiedpersonnel.

The majority of problems that may occurcan be solved without the need to contactan Authorised Service Centre.

Refer to the below table for information onpossible problems.

ENGLISH 25

With some problems, the display shows analarm code.

Problem and alarm code Possible cause and solutionYou cannot activate the appli‐ance.

• Make sure that the mains plug is connected to the mainssocket.

• Make sure that there is no damaged fuse in the fuse box.

The programme does notstart.

• Make sure that the appliance door is closed.• If the delay start is set, cancel the setting or wait for the

end of the countdown.• The appliance recharges the resin inside the water soften‐

er. The duration of the procedure is approximately 5 mi‐nutes.

The appliance does not fillwith water.The display shows i10 or i11.

• Make sure that the water tap is open.• Make sure that the pressure of the water supply is not too

low. For this information, contact your local water authori‐ty.

• Make sure that the water tap is not clogged.• Make sure that the filter in the inlet hose is not clogged.• Make sure that the inlet hose has no kinks or bends.

The appliance does not drainthe water.The display shows i20.

• Make sure that the sink spigot is not clogged.• Make sure that the interior filter system is not clogged.• Make sure that the drain hose has no kinks or bends.

The anti-flood device is on.The display shows i30.

• Close the water tap.• Make sure that the appliance is correctly installed.• Make sure the baskets are loaded as instructed in the

user manual.

Malfunction of the water lev‐el detection sensor.The display shows i41 - i44.

• Make sure that the filters are clean.• Switch the appliance off and on.

Malfunction of the washpump or the drain pump.The display shows i51 - i59 or i5A - i5F.

• Switch the appliance off and on.

The temperature of the wa‐ter inside the appliance is toohigh or malfunction of thetemperature sensor occur‐red.The display shows i61 or i69.

• Make sure that the temperature of the inlet water doesnot exceed 60°C.


ENGLISH 26

Problem and alarm code Possible cause and solutionTechnical malfunction of theappliance.The display shows iC0 or iC3.


The level of water inside theappliance is too high.The display shows iF1.

• Switch the appliance off and on.• Make sure that the filters are clean.• Make sure that the outlet hose is installed at the right

height above the floor. Refer to the installation instruc‐tions.

The appliance stops andstarts more times during op‐eration.

• It is normal. It provides optimal cleaning results and ener‐gy savings.

The programme lasts toolong.

• If the delay start option is set, cancel the delay setting orwait for the end of the countdown.

• Activating options can increase the programme duration.

The remaining time in thedisplay increases and skipsnearly to the end of the pro‐gramme duration.

• This is not a defect. The appliance is working correctly.

Small leak from the appli‐ance door.

• The appliance is not levelled. Loosen or tighten the ad‐justable feet (if applicable).

• The appliance door is not centred on the tub. Adjust therear foot (if applicable).

The appliance door is difficultto close.

• The appliance is not levelled. Loosen or tighten the ad‐justable feet (if applicable).

• Parts of the tableware are protruding from the baskets.

The appliance door opensduring the wash cycle.

• The AutoOpen is activated. This function opens the appli‐ance door during the drying phase to improve the dryingperformance and let the dishes cool down. The door re‐mains ajar.– The duration of the drying phase and the door open‐

ing time vary depending on the selected programmeand options.

– When the AutoOpen opens the door, the displayshows the remaining time of the running programme.

If you don't want the door to automatically open, deacti‐vate AutoOpen. Refer to "Settings".

Rattling or knocking soundsfrom the inside of the appli‐ance.

• The tableware is not properly arranged in the baskets. Re‐fer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

ENGLISH 27

Problem and alarm code Possible cause and solutionThe appliance trips the cir‐cuit-beaker.

• The amperage is insufficient to supply simultaneously allthe appliances in use. Check the socket amperage and thecapacity of the meter or turn off one of the appliances inuse.

• Internal electrical fault of the appliance. Contact an Au‐thorised Service Centre.

Once you have checked the appliance,deactivate and activate the appliance. If theproblem occurs again, contact an AuthorisedService Centre.

For alarm codes not described in the table,contact an Authorised Service Centre.

Warning! We do not recommendusing the appliance until theproblem has been completelyfixed. Unplug the appliance anddo not plug it in again until youare certain that it operatescorrectly.

The product number code (PNC)If you contact an Authorised Service Centre,you need to provide the product numbercode of your appliance.

The PNC can be found on the rating plate onthe appliance door. You can also check thePNC on the control panel.

Before checking the PNC, make sure theappliance is in the programme selection.

1. Press and hold simultaneously and for about 3 seconds.

The display shows the PNC of yourappliance.2. To exit the PNC presentation, press and

hold simultaneously and forabout 3 seconds.

The appliance returns to the programmeselection.

The dishwashing and drying results are not satisfactory

Problem Possible cause and solutionPoor washing results. • Refer to "Daily use", "Hints and tips" and the basket

loading leaflet.• Use more intensive washing programme.• Activate the Power Clean option to improve the washing

results of a selected programme.• Clean spray arm jets and filter. Refer to "Care and

Cleaning".

ENGLISH 28

Problem Possible cause and solutionPoor drying results. • Tableware was left for too long inside the closed appli‐

ance. Activate AutoOpen to set the automatic openingof the door and to improve the drying performance.

• There is no rinse aid or the dosage of rinse aid is notsufficient. Fill the rinse aid dispenser or set the level ofrinse aid to a higher level.

• The quality of the rinse aid can be the cause.• We recommend to use rinse aid always, even in combi‐

nation with multi-tablets.• Plastic items may need to be towel dried.• The programme does not have the drying phase. Refer

to "Programmes overview".

There are whitish streaks orbluish layers on glasses anddishes.

• The released quantity of rinse aid is too high. Adjust therinse aid level to a lower level.

• The quantity of detergent is too high.

There are stains and dry waterdrops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Ad‐just the rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

The interior of the appliance iswet.

• This is not a defect of the appliance. Humid air conden‐sates on the appliance walls.

Unusual foam during washing. • Use the detergent designed specifically for dishwash‐ers.

• There is a leak in the rinse aid dispenser. Contact an Au‐thorised Service Centre.

Traces of rust on cutlery. • There is too much salt in the water used for washing.Refer to "The water softener".

• Silver and stainless steel cutlery were placed together.Do not put silver and stainless steel items close togeth‐er.

There are residues of deter‐gent in the dispenser at theend of the programme.

• The detergent tablet was stuck in the dispenser andtherefore was not completely washed away by water.

• Water cannot wash away the detergent from the dis‐penser. Make sure that the spray arms are not blockedor clogged.

• Make sure that items in the baskets do not impede thelid of the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".• Start the Machine Care programme with a descaler or a

cleaning product designed for dishwashers.

ENGLISH 29

Problem Possible cause and solutionLimescale deposits on the ta‐bleware, on the tub and on theinside of the door.

• The level of salt is low, check the refill indicator.• The cap of the salt container is loose.• Your tap water is hard. Refer to "The water softener".• Use salt and set regeneration of the water softener

even when multi-functional tablets are used. Refer to "The water softener".

• Start the Machine Care programme with a descaler de‐signed for dishwashers.

• If limescale deposits still remain, clean the appliancewith appliance cleaners which are particularly suitablefor this purpose.

• Try a different detergent.• Contact the detergent manufacturer.

Dull, discoloured or chipped ta‐bleware.

• Make sure that only dishwasher-safe items are washedin the appliance.

• Load and unload the basket carefully. Refer to the bas‐ket loading leaflet.

• Place delicate items in the upper basket.• Activate the Gentle / Glass option to ensure special care

for glassware and delicate items.

Refer to "Before first use", "Daily use", or "Hints and tips"for other possible causes.

Technical information

Product type Fully integrated dishwasher

Dimensions Width / height / depth (mm) 596 / 818 - 898 / 550

Electrical connection 1) Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply Cold water or hot water 2) max 60 °C

Capacity Place settings 14

Power consumption Left-on mode (W) 5.0

Off-mode (W) 0.501) Refer to the rating plate for other values.2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot watersupply to decrease energy consumption.

ENGLISH 30

Environmental concerns

Recycle materials with the symbol . Putthe packaging in relevant containers torecycle it. Help protect the environment andhuman health by recycling waste of electricaland electronic appliances. Do not dispose of

appliances marked with the symbol withthe household waste. Return the product toyour local recycling facility or contact yourmunicipal office.

IKEA guarantee

How long is the IKEA guarantee valid?

This guarantee is valid for five (5) years - two(2) years if the appliance is named LAGAN orTILLREDA - from the original date ofpurchase of your appliance at IKEA or fromthe installation date with maximum limit ofthree months from the purchase date. Theoriginal sales receipt, is required as proof ofpurchase. If service work is carried out underguarantee, this will not extend theguarantee period for the appliance. Once awarranted product has been replaced, thereplaced product warranty will be valid forthe balance period from date of originalpurchase invoice.

Who will execute the service?

IKEA service provider will provide the servicethrough its own service operations orauthorized service partner network.

What does this guarantee cover?

• The guarantee covers faults of theappliance, which have been caused byfaulty construction or material faults fromthe date of purchase from IKEA or fromthe installation date with maximum limitof three months from the purchase date.

• This guarantee applies to domestic useonly.

• The exceptions are specified under theheadline “What is not covered under thisguarantee?” Within the guarantee period.

• The costs to remedy the fault e.g. repairs,parts, labour and travel will be covered,provided that the appliance is accessiblefor repair without special expenditure. On

these conditions the respective localregulations are applicable.

• Replaced parts become the property ofIKEA.

• In case of non-repairable product, theretail value of the replacement will notexceed the purchase price that was paidby the customer

What will IKEA do to correct the problem?

• IKEA appointed Service Provider willexamine the product and decide, at itssole discretion, if it is covered under thisguarantee. If considered covered, IKEAService Provider or its authorized servicepartner through its own serviceoperations, will then, at its sole discretion,either repair the defective product orreplace it with the same or a comparableproduct.

What is not covered under thisguarantee?

• Normal wear and tear.• Deliberate or negligent damage, damage

caused by failure to observe operatinginstructions, incorrect installation or byconnection to the wrong voltage, damagecaused by chemical or electro-chemicalreaction, rust, corrosion or water damageincluding but not limited to damagecaused by excessive lime in the watersupply, damage caused by abnormalenvironmental conditions.

• Consumable parts including batteries andlamps.

• Non-functional and decorative partswhich do not affect normal use of the

ENGLISH 31

appliance, including any scratches andpossible colour differences.

• Accidental damage caused by foreignobjects or substances and cleaning orunblocking of filters, drainage systems orsoap drawers.

• Damage to the following parts: ceramicglass, accessories, crockery and cutlerybaskets, feed and drainage pipes, seals,lamps and lamp covers, screens, knobs,casings and parts of casings. Unless suchdamages can be proved to have beencaused by production faults.

• Cases where no fault could be foundduring a technician’s visit.

• Repairs not carried out by our appointedservice providers and/or an authorizedservice contractual partner or where non-original parts have been used.

• Repairs caused by installation which isfaulty or not according to specification.

• The use of the appliance in a non-domestic environment i.e. professionaluse.

• Damage resulting from power outage,power surges or dips, fluctuating voltageor improper voltage All workout parts arenot covered by the guarantee e.g.: filtersand cleanliness.

• Transportation damages. If a customertransports the product to his home oranother address, IKEA is not liable for anydamage that may occur during transport.However, if IKEA delivers the product tothe customer’s delivery address, thendamage to the product that occurs duringthis delivery will be covered by IKEA.

• Cost for carrying out the initial installationof the IKEA appliance. However, if an IKEAservice provider or its authorized servicepartner repairs or replaces the applianceunder the terms of this guarantee, theservice provider or its authorized servicepartner will re-install the repairedappliance or install the replacement, ifnecessary.

• All plumping and electrical installation,are not the responsibility of IKEA, andcustomer must complete these workbefore the execution work.

How country law applies

The IKEA guarantee gives you specific legalrights, which covers or exceed localdemands. However these conditions do notlimit in any way consumer rights describedin the local legislation.

Area of validity

This warranty is valid only in the countrywhere the product has been purchased; theservices will be provided in the framework ofthe guarantee conditions.

An obligation to carry out services in theframework of the guarantee exists only if theappliance complies and is installed inaccordance with:

• the technical specifications of the countryin which the guarantee claim is made;

• the Assembly Instructions and UserManual Safety Information;

The dedicated After Sales Service for IKEAappliances:

Please don’t hesitate to contact IKEAappointed After Sales Service Provider to:

• make a service request under thisguarantee;

• ask for clarifications on installation of theIKEA appliance in the dedicated IKEAkitchen furniture;

• ask for clarification on functions of IKEAappliances.

To ensure that we provide you with the bestassistance, please read carefully theAssembly Instructions and/or the UserManual before contacting us.

How to reach us if you need our service

Please refer to the last page of this manualfor the full list of IKEA appointed contactsand relative national phone numbers.

ENGLISH 32

In order to provide you with aquicker service, we recommendthat you use the specific phonenumbers listed at the end of thismanual. Always refer to thenumbers listed in the booklet ofthe specific appliance you needan assistance for. Before callingus, assure that you have to handthe IKEA article number (8 digitcode) and the Serial Number (8digit code that can be found onthe rating plate) for the applianceof which you need our assistance.

SAVE THE SALES RECEIPT! It isyour proof of purchase andrequired for the guarantee toapply. The sales receipt alsoreports the IKEA name and articlenumber (8 digit code) for each ofthe appliances you havepurchased.

ENGLISH 33

34

UNITED ARAB EMIRATES & OMAN

Toll free: 8 004 532 رقم مجاني :Web: www.IKEA.com موقع الإنترنت :

QATAR

Toll free: 8 004 532 رقم مجاني :Web: www.IKEA.qa موقع الإنترنت :

e-mail: [email protected] البريد الإلكتروني :

EGYPT

67561:eniltoH الخط الساخن :Web: www.IKEA.eg موقع الإنترنت :


STATE OF KUWAIT

Contact centre: +965 18 40 40 8 مركز الاتصال :Web: www.IKEA.com.kw موقع الإنترنت :


JORDAN

Contact centre: +962 6 400 1000 مركز الاتصال :Web: www.IKEA.jo موقع الإنترنت :

KINGDOM OF SAUDI ARABIA

Contact centre: 92000-4532 مركز الاتصال :Our phone lines are

open: خطوط الهاتف لدينا مفتوحة :Saturday - Thursday 09:00 AM - 10:00 PM السبت - الخميس

Friday 2:00 PM - 10:00 PM يوم الجمعة

BAHRAIN

Contact centre: 80001120 مركز الاتصال :Our telephone lines

are open all day09:00 AM - 10:00 PM

خطوط الهاتف لدينا مفتوحة طوال اليوم

*

HYGIENISK - ikea.com

Documents

Transcript of HYGIENISK - ikea.com