Hydraulic Cutting Tools Catalogue

Hydraulic Cutting Tools Catalogue

PR000-0441+08

PR000-0441+06

1 PR000-0441+08

CONTENTS

CONTENTS ...................................................................................................................................................... 1

CHAPTER 1| INTRODUCTION: ......................................................................................................................... 3

CHAPTER 2| STANDARDS OF TOOLS: .............................................................................................................. 7

CHAPTER3| CLEARANCE IDENTIFICATIONS: ................................................................................................ 8

1. EXAMPLES OF POSSIBLE ORDERS ..................................................................................................... 8

CHAPTER 4| FAIK TOOLS:............................................................................................................................... 9

2. PUNCHES& DIES FOR HYDRAULIC MACHINES: ................................................................................ 9

1. TOOLS FOR FICEP ANGLE M/CS .......................................................................................................... 9

2. TOOLS FOR FICEP PUNCH PLATE M/CS ............................................................................................. 11

3. TOOLS FOR FICEP ANGLE M/C .......................................................................................................... 12

4. PUNCHES & DIES FOR ANGLE M/CS ................................................................................................. 14

5. TOOLS FOR FICEP ANGLE M/C .......................................................................................................... 15

6. SLOT TOOLS FOR FICEP ANGLE M/CS ............................................................................................... 17

7. SLOT TOOLS FOR FICEP ANGLE M/CS ................................................................................................ 18

8. SLOT TOOLS FOR FICEP ANGLE M/CS ............................................................................................... 19

9. SLOT TOOLS FOR FICEP PUNCH PLATE M/CS .................................................................................... 20

10. TOOLS FOR FICEP PUNCH PLATE M/C .............................................................................................. 21

11. ROUND TOOLS FOR FICEP ANGLE M/CS ...................................................................................... 23

12. TOOLS FOR FICEP UNIVERSAL M/CS ........................................................................................... 24

13. SLOT TOOLS FOR FICEP PUNCH PLATE ............................................................................................ 25

14. SLOT TOOLS FOR KALTENBACH M/CS ............................................................................................ 26

15. SLOT TOOLS FOR KINGSLAND M/CS ............................................................................................... 28

16. SLOT TOOLS FOR IRON WORKER M/CS ........................................................................................... 30

17. SLOT TOOLS FOR NITTO PORTABLE M/CS ....................................................................................... 32

Table of Contents:

PR000-0441+06

2 PR000-0441+08

18. SLOT TOOLS FOR EDWARDS M/CS .................................................................................................. 33

3. BLADES ............................................................................................................................................ 34

1. CIRCULAR BLADES ....................................................................................................................... 34

2. SPECIAL BLADES........................................................................................................................... 34

4. MARKING TOOLS ............................................................................................................................. 37

1. NUMBERS & LETTERS .................................................................................................................. 37

2. IDENTIFICATION STAMPS .............................................................................................................. 39

5. SPECIAL PARTS FOR HYDRAULIC MACHINES .................................................................................. 40

1. HOSING ........................................................................................................................................ 40

2. HOLDERS ..................................................................................................................................... 40

3. HOLDER COUPLING NUT .............................................................................................................. 41

4. CUTTING BLADE HOLDER .............................................................................................................. 42

6. MACHINING ACCESSOIRIES ............................................................................................................. 43

1. CLAMPS ........................................................................................................................................ 43

2. CASSETTES................................................................................................................................... 43

CHAPTER 5| TOOLS BY MACHINING: ............................................................................................................ 44

1. FICEP ............................................................................................................................................... 44

2. KALTENBACH .................................................................................................................................. 44

3. EDWARDS ........................................................................................................................................ 45

4. KINGSLAND ..................................................................................................................................... 45

5. IRON WORKER ................................................................................................................................. 45

6. NITTO ............................................................................................................................................... 45

7. MUBEA ............................................................................................................................................ 45

8. SUNRISE ........................................................................................................................................... 46

9. TAIWAN MACHINES ........................................................................................................................ 46

CHAPTER 6| TOOLS OPTIONALITIES .................................................................................................... 47

1. PUNCH DESIGN OPTIONS ................................................................................................................ 47

2. DIE DESIGN OPTIONS ..................................................................................................................... 50

CHAPTER 7| HOW TO ORDER .................................................................................................................. 51

CHAPTER 8| CONTACTS ................................................................................................................................ 52

PR000-0441+06

3 PR000-0441+08

CHAPTER 1| INTRODUCTION:

FAIK Manufacturing Co. "FAIK" is an Egyptian company that has been founded under the

Egyptian Law in 1994, offering a wide range of feeding products for different sectors of

industry with special focus on Automotive Industry. FAIK has been an Egyptian Brand

Name in the field of spare parts since 1960. Faik covers the following components and spare parts for the following fields of industry:

Feeding Industries for Construction Industry.

Vehicles spare parts and automotive feeding industry.

Cement Industry

Petroleum Industry

Scaffolding Parts

Utilities pipes industry (Water and Wastewater).

Rubber Industry

Rail Way Station Industry

Tools for sheet metals

Sheet Metals Industry.

Anchor bolts.

Building industry (Metal Construction).

Other Industries.

In this catalogue we would like to focus on the Sheet Metal Toolings where this is a specified area to discuss the relation between Faik Tooling and other Machines, informing you how can you pick your demand that comply with other machines knowing that the sheet metal Toolings are one of our fields.

Toolings by Faik comply with a lot of sheet metal machines as:

Fecip Mubea Sun Rise Iron Worker Kaltenbach Kings Land Nitto Edward Geka M/C Taiwan M/C

We will find later on, what is the relation between the sheet metal machines and Faik Products to successfully manage your choice of our product and your sheet metal machine.

As also you will find the specifications and the technical procedures applied to our products.

dp106

Text Box

Back To Contents P1

PR000-0441+06

4 PR000-0441+08

FAIK has adopted international and national Codes and Standard during various phases of the production, including:

AISI American Iran and Steel Institute. ANSI American National Standard Institute. ASME American Society of Mechanical Engineers. ASTM American Society for Testing and Materials. DIN German Institute Standardization. ECT Egyptian Code for testing. ISO International Organization for Standardization. JIS Japanese Institute Standardization

dp106

Text Box

Back To Contents P1

PR000-0441+06

5 PR000-0441+08

dp106

Text Box

Back To Contents P1

PR000-0441+06

6 PR000-0441+08

For more information about Faik please contact us and order our General Booklet in

order to get to know Faik more

dp106

Text Box

Back To Contents P1

PR000-0441+06

7 PR000-0441+08

CHAPTER 2| STANDARDS OF TOOLS:

In the performance of our work, FAIK uses the most advanced tools, techniques, and machinery. The plant is extensively equipped with progressive and modern machines that ensure that FAIK will remain in the highest competitive level. The Firm is equipped with more than 60 different machines enabling us to tackle the most demanding jobs that will be discussed later on. FAIK products are specifically designed to guarantee high standards and high quality. The Coming Chapter show specific toolings for a variety of machine brands. Faik is not limited to these products, but we would like to help in designing and manufacturing new products or new sizes to fit any application. The tools mentioned in this catalogue are available upon request. Faik has possessed a certain Lifecycle to manufacture the tools with a unique standard that is easily complied with all of the manufacturing process and specification NO. FS_5008 as:

Material: All the Toolings by Faik are realized by high quality material imported from Austrian materials that are inspected by us. These materials are machined to produce the toolings performed by Faik that witness the birth of an Egyptian Product carrying its own Egyptian Certificate of Origin.

Machinery: All Machinery process that is applied to the products are on CNC Machines where each product has its own program and its own line.

Specifications: All Toolings are Heat-treated and controlled well. We can supply all decimal sizes, not mention in the catalogue upon request. Special clearances can be applied for any products of any material.

Please do not hesitate to contact us for special requirements needed, where we are specialized in custom-made Toolings.

We deliver As Promised. Faik Manufacturing Co.

dp106

Text Box

Back To Contents P1

PR000-0441+06

8 PR000-0441+08

CHAPTER3| CLEARANCE IDENTIFICATIONS:

Clearance Identification helps the user to pick up the correct die for the needed Punch. As between the punch size and the die size there must be difference due to the fraction between the punch and the die during the punching process.

1. EXAMPLES OF POSSIBLE ORDERS

• Request of die for 25.5 mm round punch. The diameter of the die to be inserted in the order is 26.9 mm. • Request of die for square punch with 25.5 mm side. Consider the side of the square as a diameter, therefore the size of the square of the die to be inserted in the order is 26.9 mm. • Request of die for punch for 9 mm x 25.5 mm oval or rectangular tool. The size to considerable ways the smaller, therefore the increase rate referred to 9 mm has to be added also to the bigger size. The size of the shape of the die to be inserted in the order is 9.7 x 26.2 mm.

Standard Clearance

Punch Size Die Size

< 4 0.4

4.1 ÷ 7 0.6

7.1 ÷ 10 0.7

10.1 ÷ 13 0.8

13.1 ÷ 16 1

16.1 ÷ 20 1.2

20.1 ÷ 23 1.3

23.1 ÷ 26 1.4

26.1 ÷ 29 1.5

29.1 ÷ 32 1.6

32.1 ÷ 35 1.7

35.1 ÷ 40 1.8

40> 2

R= Material Tensile

Strength

S =

Mate

rial

Th

ickn

ess

G = Material Clearance

dp106

Text Box

Back To Contents P1

PR000-0441+06

9 PR000-0441+08

CHAPTER 4| FAIK TOOLS:

2. PUNCHES& DIES FOR HYDRAULIC MACHINES:

1. TOOLS FOR FICEP ANGLE M/CS

These types of punches and dies are computable with ficep angles machines

Where they are computable of Ficep Punch# A21922 and Die# A21578

Punch Code Size D Die Code Size D1 FS31-00070 7.00 FS51-00076 7.60 FS31-00075 7.50 FS51-00082 8.20 FS31-00080 8.00 FS51-00087 8.70 FS31-00085 8.50 FS51-00092 9.20 FS31-00090 9.00 FS51-00097 9.70 FS31-00095 9.50 FS51-00102 10.20 FS31-00100 10.00 FS51-00108 10.80 FS31-00105 10.50 FS51-00113 11.30 FS31-00110 11.00 FS51-00118 11.80 FS31-00115 11.50 FS51-00123 12.30 FS31-00120 12.00 FS51-00128 12.80 FS31-00125 12.50 FS51-00133 13.30 FS31-00130 13.00 FS51-00138 13.80 FS31-00135 13.50 FS51-00145 14.50 FS31-00140 14.00 FS51-00150 15.00 FS31-00145 14.50 FS51-00155 15.50 FS31-00150 15.00 FS51-00160 16.00 FS31-00155 15.50 FS51-00165 16.50 FS31-00160 16.00 FS51-00170 17.00 FS31-00165 16.50 FS51-00177 17.70 FS31-00170 17.00 FS51-00182 18.20 FS31-00175 17.50 FS51-00187 18.70 FS31-00180 18.00 FS51-00192 19.20 FS31-00185 18.50 FS51-00197 19.70 FS31-00190 19.00 FS51-00202 20.20 FS31-00195 19.50 FS51-00207 20.70 FS31-00200 20.00 FS51-00212 21.20 FS31-00205 20.50 FS51-00218 21.80 FS31-00210 21.00 FS51-00223 22.30

FS 30

FS 51

PR000-0441+06

10 PR000-0441+08

Punch Code Size D Die Code Size D1 FS31-00215 21.50 FS51-00228 22.80 FS31-00220 22.00 FS51-00233 23.30 FS31-00225 22.50 FS51-00238 23.80 FS31-00230 23.00 FS51-00243 24.30 FS31-00235 23.50 FS51-00249 24.90 FS31-00240 24.00 FS51-00254 25.40 FS31-00245 24.50 FS51-00259 25.90 FS31-00250 25.00 FS51-00264 26.40 FS31-00255 25.50 FS51-00269 26.90 FS31-00260 26.00 FS51-00274 27.40 FS31-00265 26.50 FS51-00280 28.00 FS31-00272 27.00 FS51-00285 28.50 FS31-00275 27.50 FS51-00290 29.00 FS31-00280 28.00 FS51-00295 29.50

FS 30

FS 30

FS 51

PR000-0441+06

11 PR000-0441+08

2. TOOLS FOR FICEP PUNCH PLATE M/CS

These types of punches and dies are computable with Ficep punch plate machines


Punch Code Size D Die Code Size D

FS31-00070 7.00 FS51-00076 7.60FS31-00075 7.50 FS51-00082 8.20FS31-00080 8.00 FS51-00087 8.70FS31-00085 8.50 FS51-00092 9.20FS31-00090 9.00 FS51-00097 9.70FS31-00095 9.50 FS51-00102 10.20FS31-00100 10.00 FS51-00108 10.80FS31-00105 10.50 FS51-00113 11.30FS31-00110 11.00 FS51-00118 11.80FS31-00115 11.50 FS51-00123 12.30FS31-00120 12.00 FS51-00128 12.80FS31-00125 12.50 FS51-00133 13.30FS31-00130 13.00 FS51-00138 13.80FS31-00135 13.50 FS51-00145 14.50FS31-00140 14.00 FS51-00150 15.00FS31-00145 14.50 FS51-00155 15.50FS31-00150 15.00 FS51-00160 16.00FS31-00155 15.50 FS51-00165 16.50FS31-00160 16.00 FS51-00170 17.00FS31-00165 16.50 FS51-00177 17.70FS31-00170 17.00 FS51-00182 18.20FS31-00175 17.50 FS51-00187 18.70FS31-00180 18.00 FS51-00192 19.20FS31-00185 18.50 FS51-00197 19.70FS31-00190 19.00 FS51-00202 20.20FS31-00195 19.50 FS51-00207 20.70FS31-00200 20.00 FS51-00212 21.20

FS 31

FS 51

PR000-0441+06

12 PR000-0441+08

3. TOOLS FOR FICEP ANGLE M/C

These types of punches and dies are computable with Ficep angles machines


Punch Code Size D Die Code Size D FS32-00070 7.00 FS51-00076 7.60 FS32-00075 7.50 FS51-00082 8.20 FS32-00080 8.00 FS51-00087 8.70 FS32-00085 8.50 FS51-00092 9.20 FS32-00090 9.00 FS51-00097 9.70 FS32-00095 9.50 FS51-00102 10.20 FS32-00100 10.00 FS51-00108 10.80 FS32-00105 10.50 FS51-00113 11.30 FS32-00110 11.00 FS51-00118 11.80 FS32-00115 11.50 FS51-00123 12.30 FS32-00120 12.00 FS51-00128 12.80 FS32-00125 12.50 FS51-00133 13.30 FS32-00130 13.00 FS51-00138 13.80 FS32-00135 13.50 FS51-00145 14.50 FS32-00140 14.00 FS51-00150 15.00 FS32-00145 14.50 FS51-00155 15.50 FS32-00150 15.00 FS51-00160 16.00 FS32-00155 15.50 FS51-00165 16.50 FS32-00160 16.00 FS51-00170 17.00 FS32-00165 16.50 FS51-00177 17.70 FS32-00170 17.00 FS51-00182 18.20 FS32-00175 17.50 FS51-00187 18.70 FS32-00180 18.00 FS51-00192 19.20 FS32-00185 18.50 FS51-00197 19.70 FS32-92190 19.00 FS51-00202 20.20 FS32-00195 19.50 FS51-00207 20.70 FS32-00200 20.00 FS51-00212 21.20 FS32-00205 20.50 FS51-00218 21.80 FS32-00210 21.00 FS51-00223 22.30 FS32-00215 21.50 FS51-00228 22.80 FS32-00220 22.00 FS51-00233 23.30 FS32-00225 22.50 FS51-00238 23.80

FS 32

FS 51

PR000-0441+06

13 PR000-0441+08

Punch Code Size D Die Code Size D FS32-00230 23.00 FS51-00243 24.30 FS32-00235 23.50 FS51-00249 24.90 FS32-00240 24.00 FS51-00254 25.40 FS32-00245 24.50 FS51-00259 25.90 FS32-00250 25.00 FS51-00264 26.40 FS32-00255 25.50 FS51-00269 26.90 FS32-00260 26.00 FS51-00274 27.40 FS32-00265 26.50 FS51-00280 28.00 FS32-00272 27.00 FS51-00285 28.50 FS32-00275 27.50 FS51-00290 29.00 FS32-00280 28.00 FS51-00295 29.50 FS3 2-00285 28.50 FS51-00300 30.00 FS32-00290 29.00 FS51-00305 30.50 FS32-00295 29.50 FS51-00311 31.10 FS32-00300 30.00 FS51-00316 31.60 FS32-00305 30.50 FS51-00321 32.10 FS32-00310 31.00 FS51-00326 32.60 FS32-00315 31.50 FS51-00331 33.10

FS 32

FS 51

PR000-0441+06

14 PR000-0441+08

4. PUNCHES & DIES FOR ANGLE M/CS


Where they are computable of Ficep Punch and Die# A26371

Punch Code Size D Die Code Size D FS33-00280 28.00 FS52-00295 29.50 FS33-00285 28.50 FS52-00300 30.00 FS33-00290 29.00 FS52-00305 30.50 FS33-00295 29.50 FS52-00311 31.10 FS33-00300 30.00 FS52-00316 31.60 FS33-00305 30.50 FS52-00321 32.10 FS33-00310 31.00 FS52-00326 32.60 FS33-00315 31.50 FS52-00331 33.10 FS33-00320 32.00 FS52-00336 33.60 FS33-00325 32.50 FS52-00342 34.20 FS33-00330 33.00 FS52-00347 34.70 FS33-00330 33.00 FS52-00347 34.70 FS33-00335 33.50 FS52-00352 35.20 FS33-00340 34.00 FS52-00357 35.70 FS33-00355 35.50 FS52-00373 37.30 FS33-00360 36.00 FS52-00378 37.80 FS33-00365 36.50 FS52-00383 38.30 FS33-00370 37.00 FS52-00388 38.80 FS33-00375 37.50 FS52-00393 39.30 FS33-00380 38.00 FS52-00398 39.80

FS 33

FS 52

PR000-0441+06

15 PR000-0441+08

5. TOOLS FOR FICEP ANGLE M/C



Punch Code Size D Die Code Size D FS34-00070 7.00 FS50-00076 7.60 FS34-00075 7.50 FS50-00082 8.20 FS34-00080 8.00 FS50-00087 8.70 FS34-00085 8.50 FS50-00092 9.20 FS34-00090 9.00 FS50-00097 9.70 FS34-00095 9.50 FS50-00102 10.20 FS34-00100 10.00 FS50-00108 10.80 FS34-00105 10.50 FS50-00113 11.30 FS34-00110 11.00 FS50-00118 11.80 FS34-00115 11.50 FS50-00123 12.30 FS34-00120 12.00 FS50-00128 12.80 FS31-00125 12.50 FS50-00133 13.30 FS34-00130 13.00 FS50-00138 13.80 FS34-00135 13.50 FS50-00145 14.50 FS34-00140 14.00 FS50-00150 15.00 FS34-00145 14.50 FS50-00155 15.50 FS34-00150 15.00 FS50-00160 16.00 FS34-00155 15.50 FS50-00165 16.50 FS34-00160 16.00 FS50-00170 17.00 FS34-00165 16.50 FS50-00177 17.70 FS34-00170 17.00 FS50-00182 18.20 FS34-00175 17.50 FS50-00187 18.70 FS34-00180 18.00 FS50-00192 19.20 FS34-00185 18.50 FS50-00197 19.70 FS34-00190 19.00 FS50-00202 20.20 FS34-00195 19.50 FS50-00207 20.70 FS34-00200 20.00 FS50-00212 21.20 FS34-00205 20.50 FS50-00218 21.80 FS34-00210 21.00 FS50-00223 22.30 FS34-00215 21.50 FS50-00228 22.80 FS34-00220 22.00 FS50-00233 23.30 FS34-00225 22.50 FS50-00238 23.80

FS 34

FS 50

PR000-0441+06

16 PR000-0441+08

FS34-00230 23.00 FS50-00243 24.30 FS34-00235 23.50 FS50-00249 24.90 FS34-00240 24.00 FS50-00254 25.40 FS34-00245 24.50 FS50-00259 25.90 FS34-00250 25.00 FS50-00264 26.40 FS34-00255 25.50 FS50-00269 26.90 FS34-00260 26.00 FS50-00274 27.40

Punch Code Size D Die Code Size D

FS 34

FS 50

PR000-0441+06

17 PR000-0441+08

6. SLOT TOOLS FOR FICEP ANGLE M/CS



Punch Code Size AXB Die Code Size AXB FS35-00100/220 10x22

FS54-00107/227 10.7X22.7 FS35-00110/230 11X23

FS54-00118/238 11.8X23.8 FS35-00120/240 12X24

FS54-00128/248 12.8X24.8 FS35-00130/250 13X25

FS54-00138/258 13.8X25.8 FS35-00140/260 14X26

FS54-00150/270 15.0X27.0 FS35-00150/270 15X27

FS54-00160/280 16.0X28.0 FS35-00160/280 16X28

FS54-00170/290 17.0X29.0 FS35-00170/290 17X29

FS54-00182/302 18.2X30.2 FS35-00180/300 18X30

FS54-00192/302 19.2X31.2 FS35-00190/300 19X30

FS54-00202/302 20.2X31.2 FS35-00200/300 20X30

FS54-00212/302 21.2X31.2 FS35-00210/300 21X30

FS54-00222/302 22.2X31.2 FS35-00220/300 22X30

FS54-00232/302 23.2X31.2 FS35-00230/300 23X30

FS54-00242/302 24.2X31.2 FS35-00240/300 24X30

FS54-00252/302 25.2X31.2 FS35-00250/300 25X30

FS54-00262/302 26.2X31.2 FS35-00260/300 26X30

FS54-00272/302 27.2X31.2 FS35-00180/260 18X26

FS54-00192/272 19.2X27.2 FS35-00200/260 20X26

FS54-00212/272 21.2X27.2 FS35-00220/260 22X26

FS54-00232/272 23.2X27.2

FS 35

FS 54

PR000-0441+06

18 PR000-0441+08




Punch Code Size AXB Die Code Size A1XB1 FS36-00120/330 12.00 x 30.00 FS53-00128/308 12.80 X 30.80 FS36-00130/320 13.00 x 32.00 FS53-00138/328 13.80 X 32.80 FS36-00140/340 14.00 x 34.00 FS53-00150/350 15.00 X 35.00 FS36-00150/360 15.00 x 36.00 FS53-00160/370 16.00 X 37.00 FS36-00160/380 16.00 x 38.00 FS53-00170/390 17.00 X 39.00 FS36-00170/400 17.00 x 40.00 FS53-00182/412 18.20 X 41.20 FS36-00180/420 18.00 x 42.00 FS53-00192/432 19.20 X 43.20 FS36-00190/440 19.00 x 44.00 FS53-00202/452 20.20 X 45.20 FS36-00200/450 20.00 x 45.00 FS53-00212/462 21.20 X 46.20 FS36-00210/300 21.00 x 30.00 FS53-00223/313 22.30 X 31.30 FS36-00220/300 22.00 x 30.00 FS53-00233/313 23.30 X 31.30 FS36-00220/350 22.00 x 35.00 FS53-00233/363 23.30 X 36.30 FS36-00220/360 22.00 x 36.00 FS53-00232/373 23.30 X 37.30 FS36-00220/380 22.00 x 38.00 FS53-00242/393 23.30 X 39.30 FS36-00220/400 22.00 x 40.00 FS53-00252/413 23.30 X 41.30 FS36-00220/420 22.00 x 42.00 FS53-00262/433 23.30 X 43.30 FS36-00220/450 22.00 x 45.00 FS53-00272/463 23.30 X 46.30 FS36-00240/400 24.00 x 40.00 FS53-00192/414 25.40 X 41.40 FS36-00240/460 24.00 x 46.00 FS53-00232/474 25.40 X 47.40

FS 36

FS 53

PR000-0441+06

19 PR000-0441+08




Punch Code Size AXB Die Code Size A1XB1 FS37-00230/260 23.00 X 26.00 FS53-00107/227 10.70 X 22.70 FS37-00240/280 24.00 x 28.00 FS53-00118/238 11.80 X 23.80 FS37-00240/280 24.00 x 28.00 FS53-00128/248 12.80 X 24.80 FS37-00240/320 24.00 x 32.00 FS53-00138/258 13.80 X 25.80 FS37-00240/360 24.00 X 36.00 FS53-00150/270 15.00 X 27.00 FS37-00240/380 24.00 X 38.00 FS53-00160/280 16.00 X 28.00 FS37-00240/400 24.00 X 40.00 FS53-00170/290 17.00 X 29.00 FS37-00300/360 30.00 X 36.00 FS53-00182/302 18.20 X 30.20 FS37-00300/380 30.00 X 38.00 FS53-00192/302 19.20 X 31.20 FS37-00300/400 30.00 X 40.00 FS53-00202/302 20.20 X 31.20 FS37-00300/420 30.00 X 42.00 FS53-00212/302 21.20 X 31.20 FS37-00300/430 30.00 X 43.00 FS53-00222/302 22.20 X 31.20 FS37-00300/450 30.00 X 45.00 FS53-00232/302 23.20 X 31.20 FS37-00320/400 32.00 X 40.00 FS53-00242/302 24.20 X 31.20 FS37-00320/420 32.00 X 42.00 FS53-00252/302 25.20 X 31.20 FS37-00320/430 32.00 X 43.00 FS53-00262/302 26.20 X 31.20 FS37-00320/450 32.00 X 45.00 FS53-00272/302 27.20 X 31.20 FS37-00340/400 34.00 X 40.00 FS53-00192/272 19.20 X 27.20 FS37-00340/450 34.00 X 45.00 FS53-00212/272 21.20 X 27.20 FS37-00360/450 36.00 X 45.00 FS53-00232/272 23.20 X 27.20

FS 37

FS 53

PR000-0441+06

20 PR000-0441+08

9. SLOT TOOLS FOR FICEP PUNCH PLATE M/CS




FS 37

FS 54

PR000-0441+06

21 PR000-0441+08

10. TOOLS FOR FICEP PUNCH PLATE M/C


Punch Code Size D Die Code Size D1 FS38-00070 7.00 FS55-00076 7.60 FS38-00075 7.50 FS55-00082 8.20 FS38-00080 8.00 FS55-00087 8.70 FS38-00085 8.50 FS55-00092 9.20 FS38-00090 9.00 FS55-00097 9.70 FS38-00095 9.50 FS55-00102 10.20 FS38-00100 10.00 FS55-00108 10.80 FS38-00105 10.50 FS55-00113 11.30 FS38-00110 11.00 FS55-00118 11.80 FS38-00115 11.50 FS55-00123 12.30 FS38-00120 12.00 FS55-00128 12.80 FS38-00125 12.50 FS55-00133 13.30 FS38-00130 13.00 FS55-00138 13.80 FS38-00135 13.50 FS55-00145 14.50 FS38-00140 14.00 FS55-00150 15.00 FS38-00145 14.50 FS55-00155 15.50 FS38-00150 15.00 FS55-00160 16.00 FS38-00155 15.50 FS55-00165 16.50 FS38-00160 16.00 FS55-00170 17.00 FS38-00165 16.50 FS55-00177 17.70 FS38-00170 17.00 FS55-00182 18.20 FS38-00175 17.50 FS55-00187 18.70 FS38-00180 18.00 FS55-00192 19.20 FS38-00185 18.50 FS55-00197 19.70 FS38-00190 19.00 FS55-00202 20.20 FS38-00195 19.50 FS55-00207 20.70 FS38-00200 20.00 FS55-00212 21.20 FS38-00205 20.50 FS55-00218 21.80 FS38-00210 21.00 FS55-00223 22.30 FS38-00215 21.50 FS55-00228 22.80 FS38-00220 22.00 FS55-00233 23.30 FS38-00225 22.50 FS55-00238 23.80 FS38-00230 23.00 FS55-00243 24.30 FS38-00235 23.50 FS55-00249 24.90 FS38-00240 24.00 FS55-00254 25.40

FS 38

FS 55

PR000-0441+06

22 PR000-0441+08

Punch Code Size D Die Code Size D1 FS38-00245 24.50 FS55-00259 25.90 FS38-00250 25.00 FS55-00264 26.40 FS38-00255 25.50 FS55-00269 26.90 FS38-00260 26.00 FS55-00274 27.40 FS38-00265 26.50 FS55-00280 28.00 FS38-00272 27.00 FS55-00285 28.50 FS38-00275 27.50 FS55-00290 29.00 FS38-00280 28.00 FS55-00295 29.50

FS 38

FS 55

PR000-0441+06

23 PR000-0441+08

11. ROUND TOOLS FOR FICEP ANGLE M/CS



Punch Code Size D Die Code Size D1 FS40-00060 6.00 FS51-00066 6.60 FS40-00065 6.50 FS51-00071 7.10 FS40-00070 7.00 FS51-00076 7.60 FS40-00075 7.50 FS51-00082 8.20 FS40-00080 8.00 FS51-00087 8.70 FS40-00085 8.50 FS51-00092 9.20 FS40-00090 9.00 FS51-00097 9.70 FS40-00095 9.50 FS51-00102 10.20 FS40-00100 10.00 FS51-00108 10.80 FS40-00105 10.50 FS51-00113 11.30 FS40-00110 11.00 FS51-00118 11.80 FS40-00115 11.50 FS51-00123 12.30 FS40-00120 12.00 FS51-00128 12.80 FS40-00125 12.50 FS51-00133 13.30 FS40-00130 13.00 FS51-00138 13.80 FS40-00135 13.50 FS51-00145 14.50 FS40-00140 14.00 FS51-00150 15.00 FS40-00145 14.50 FS51-00155 15.50 FS40-00150 15.00 FS51-00160 16.00 FS40-00160 16.00 FS51-00172 17.20 FS40-00170 17.00 FS51-00182 18.20 FS40-00180 18.00 FS51-00192 19.20 FS40-00200 20.00 FS51-00213 21.30 FS40-00220 22.00 FS51-00223 22.30 FS40-00240 24.00 FS51-00244 24.40 FS40-00260 26.00 FS51-00274 27.40

FS 40

FS 51

PR000-0441+06

24 PR000-0441+08

12. TOOLS FOR FICEP UNIVERSAL M/CS

These types of punches and dies are computable with Ficep universal machines


Punch Code Size D Die Code Size D1 FS41-00060 6.00 FS58-00066 6.60 FS41-00065 6.50 FS58-00071 7.10 FS41-00070 7.00 FS58-00076 7.60 FS41-00075 7.50 FS58-00082 8.20 FS41-00080 8.00 FS58-00087 8.70 FS41-00085 8.50 FS58-00092 9.20 FS41-00090 9.00 FS58-00097 9.70 FS41-00095 9.50 FS58-00102 10.20 FS41-00100 10.00 FS58-00108 10.80 FS41-00105 10.50 FS58-00113 11.30 FS41-00110 11.00 FS58-00118 11.80 FS41-00115 11.50 FS58-00123 12.30 FS41-00120 12.00 FS58-00128 12.80 FS41-00125 12.50 FS58-00133 13.30 FS41-00130 13.00 FS58-00138 13.80 FS41-00135 13.50 FS58-00145 14.50 FS41-00140 14.00 FS58-00150 15.00 FS41-00145 14.50 FS58-00155 15.50 FS41-00150 15.00 FS58-00160 16.00 FS41-00160 16.00 FS58-00172 17.20 FS41-00170 17.00 FS58-00182 18.20 FS41-00180 18.00 FS58-00192 19.20 FS41-00200 20.00 FS58-00213 21.30 FS41-00220 22.00 FS58-00223 22.30 FS41-00240 24.00 FS58-00244 24.40 FS41-00260 26.00 FS58-00274 27.40

FS 41

FS 58

PR000-0441+06

25 PR000-0441+08

13. SLOT TOOLS FOR FICEP PUNCH PLATE




FS 43

FS 54

PR000-0441+06

26 PR000-0441+08

14. SLOT TOOLS FOR KALTENBACH M/CS

These types of punches and dies are computable with Kaltenbach machines

Punch Code Size D Die Code Size D1 FS45-00090 9.00 FS61-00097 9.70 FS45-00095 9.50 FS61-00102 10.20 FS45-00100 10.00 FS61-00107 10.70 FS45-00105 10.50 FS61-00112 11.20 FS45-00110 11.00 FS61-00117 11.70 FS45-00115 11.50 FS61-00127 12.20 FS45-00120 12.00 FS61-00127 12.70 FS45-00125 12.50 FS61-00132 13.20 FS45-00130 13.00 FS61-00137 13.70 FS45-00135 13.50 FS61-00142 14.20 FS45-00140 14.00 FS61-00128 14.70 FS45-00145 14.50 FS61-00152 15.20 FS45-00150 15.00 FS61-00158 15.80 FS45-00155 15.50 FS61-00163 16.30 FS45-00160 16.00 FS61-00168 16.80 FS45-00165 16.50 FS61-00173 17.30 FS45-00170 17.00 FS61-00180 18.00 FS45-00175 17.50 FS61-00185 18.50 FS45-00180 18.00 FS61-00190 19.00 FS45-00185 18.50 FS61-00195 19.50 FS45-00190 19.00 FS61-00200 20.00 FS45-00195 19.50 FS61-00205 20.50 FS45-00200 20.00 FS61-00210 21.00 FS45-00210 21.00 FS61-00220 22.00 FS45-00215 21.50 FS61-00225 22.50 FS45-00220 22.00 FS61-00230 23.00 FS45-00225 22.50 FS61-00235 23.50 FS45-00230 23.00 FS61-00240 24.00 FS45-00235 23.50 FS61-00245 24.50 FS45-00240 24.00 FS61-00252 25.20 FS45-00245 24.50 FS61-00257 25.70 FS45-00255 25.00 FS61-00262 26.30 FS45-00255 25.50 FS61-00267 26.80 FS45-00265 26.50 FS61-00278 27.80 FS45-00260 26.00 FS61-00273 27.30

FS 45

FS 61

PR000-0441+06

27 PR000-0441+08

Punch Code Size D Die Code Size D1 FS45-00265 26.50 FS61-00278 27.80 FS45-00270 27.00 FS61-00283 28.30 FS45-00275 27.50 FS61-00288 28.80 FS45-00280 28.00 FS61-00295 29.50 FS45-00285 28.50 FS61-00300 30.00 FS45-00290 29.00 FS61-00305 30.50 FS45-00295 29.50 FS61-00310 31.00 FS45-00300 30.00 FS61-00315 31.50

FS 45

FS 61

PR000-0441+06

28 PR000-0441+08

15. SLOT TOOLS FOR KINGSLAND M/CS

These types of punches and dies are computable with Kingsland machines

Punch Code Size D Die Code Size D FS46-00090 9.00 FS62-00097 9.70 FS46-00095 9.50 FS62-00102 10.20 FS46-00100 10.00 FS62-00107 10.70 FS46-00105 10.50 FS62-00112 11.20 FS46-00110 11.00 FS62-00117 11.70 FS46-00115 11.50 FS62-00127 12.20 FS46-00120 12.00 FS62-00127 12.70 FS46-00125 12.50 FS62-00132 13.20 FS46-00130 13.00 FS62-00137 13.70 FS46-00135 13.50 FS62-00142 14.20 FS46-00140 14.00 FS62-00128 14.70 FS46-00145 14.50 FS62-00152 15.20 FS46-00150 15.00 FS62-00158 15.80 FS46-00155 15.50 FS62-00163 16.30 FS46-00160 16.00 FS62-00168 16.80 FS46-00165 16.50 FS62-00173 17.30 FS46-00170 17.00 FS62-00180 18.00 FS46-00175 17.50 FS62-00185 18.50 FS46-00180 18.00 FS62-00190 19.00 FS46-00185 18.50 FS62-00195 19.50 FS46-00190 19.00 FS62-00200 20.00 FS46-00195 19.50 FS62-00205 20.50 FS46-00200 20.00 FS62-00210 21.00 FS46-00205 20.50 FS62-00212 21.20 FS46-00210 21.00 FS62-00220 22.00 FS46-00215 21.50 FS62-00225 22.50 FS46-00220 22.00 FS62-00230 23.00 FS46-00225 22.50 FS62-00235 23.50 FS46-00230 23.00 FS62-00240 24.00 FS46-00235 23.50 FS62-00245 24.50 FS46-00240 24.00 FS62-00252 25.20 FS46-00255 25.00 FS62-00262 26.30 FS46-00255 25.50 FS62-00267 26.80 FS46-00265 26.50 FS62-00278 27.80 FS46-00260 26.00 FS62-00273 27.30

FS 46

FS 62

PR000-0441+06

29 PR000-0441+08

Punch Code Size D Die Code Size D FS46-00265 26.50 FS62-00278 27.80 FS46-00270 27.00 FS62-00283 28.30 FS46-00275 27.50 FS62-00288 28.80 FS46-00280 28.00 FS62-00295 29.50 FS46-00285 28.50 FS62-00300 30.00 FS45-00290 29.00 FS62-00305 30.50 FS46-00295 29.50 FS62-00310 31.00 FS46-00300 30.00 FS62-00315 31.50

FS 46

FS 62

PR000-0441+06

30 PR000-0441+08

16. SLOT TOOLS FOR IRON WORKER M/CS

These types of punches and dies are computable with Iron Worker machines

Where they are computable of Ficep Punch# 8-IWP and Die# 15186

Punch Code Size D Die Code Size D1 FS47-00090 9.00 FS63-00097 9.70 FS47-00095 9.50 FS63-00102 10.20 FS47-00100 10.00 FS63-00107 10.70 FS47-00105 10.50 FS63-00112 11.20 FS47-00110 11.00 FS63-00117 11.70 FS47-00115 11.50 FS63-00127 12.20 FS47-00120 12.00 FS63-00127 12.70 FS47-00125 12.50 FS63-00132 13.20 FS47-00130 13.00 FS63-00137 13.70 FS47-00135 13.50 FS63-00142 14.20 FS47-00140 14.00 FS63-00128 14.70 FS47-00145 14.50 FS63-00152 15.20 FS47-00150 15.00 FS63-00158 15.80 FS47-00155 15.50 FS63-00163 16.30 FS47-00160 16.00 FS63-00168 16.80 FS47-00165 16.50 FS63-00173 17.30 FS47-00170 17.00 FS63-00180 18.00 FS47-00175 17.50 FS63-00185 18.50 FS47-00180 18.00 FS63-00190 19.00 FS47-00185 18.50 FS63-00195 19.50 FS47-00190 19.00 FS63-00200 20.00 FS47-00195 19.50 FS63-00205 20.50 FS47-00200 20.00 FS63-00210 21.00 FS47-00205 20.50 FS63-00212 21.20 FS47-00210 21.00 FS63-00220 22.00 FS47-00215 21.50 FS63-00225 22.50 FS47-00220 22.00 FS63-00230 23.00 FS47-00225 22.50 FS63-00235 23.50 FS47-00230 23.00 FS63-00240 24.00 FS47-00235 23.50 FS63-00245 24.50 FS47-00240 24.00 FS63-00252 25.20 FS47-00245 24.50 FS63-00257 25.70 FS47-00255 25.00 FS63-00262 26.30

FS 47

FS 63

PR000-0441+06

31 PR000-0441+08

Punch Code Size D Die Code Size D1 FS47-00255 25.50 FS63-00267 26.80 FS47-00260 26.00 FS63-00273 27.30 FS47-00265 26.50 FS63-00278 27.80 FS47-00270 27.00 FS63-00283 28.30 FS47-00275 27.50 FS63-00288 28.80 FS47-00280 28.00 FS63-00295 29.50 FS47-00285 28.50 FS63-00300 30.00 FS47-00290 29.00 FS63-00305 30.50 FS47-00295 29.50 FS63-00310 31.00 FS47-00300 30.00 FS63-00315 31.50

FS 47

FS 63

PR000-0441+06

32 PR000-0441+08

17. SLOT TOOLS FOR NITTO PORTABLE M/CS

These types of punches and dies are computable with Nitto machines

Punch Code Size D Die Code Size D1 FS48-00090 9.00 FS64-00097 9.70 FS48-00095 9.50 FS64-00102 10.20 FS48-00100 10.00 FS64-00107 10.70 FS48-00105 10.50 FS64-00112 11.20 FS48-00110 11.00 FS64-00117 11.70 FS48-00115 11.50 FS64-00127 12.20 FS48-00120 12.00 FS64-00127 12.70 FS48-00125 12.50 FS64-00132 13.20 FS48-00130 13.00 FS64-00137 13.70 FS48-00135 13.50 FS64-00142 14.20 FS48-00140 14.00 FS64-00128 14.70 FS48-00145 14.50 FS64-00152 15.20 FS48-00150 15.00 FS64-00158 15.80 FS48-00155 15.50 FS64-00163 16.30 FS48-00160 16.00 FS64-00168 16.80 FS48-00165 16.50 FS64-00173 17.30 FS48-00170 17.00 FS64-00180 18.00 FS48-00175 17.50 FS64-00185 18.50 FS48-00180 18.00 FS64-00190 19.00 FS48-00185 18.50 FS64-00195 19.50 FS48-00190 19.00 FS64-00200 20.00 FS48-00195 19.50 FS64-00205 20.50 FS48-00200 20.00 FS64-00210 21.00 FS48-00205 20.50 FS64-00212 21.20 FS48-00210 21.00 FS64-00220 22.00 FS48-00215 21.50 FS64-00225 22.50 FS48-00220 22.00 FS64-00230 23.00

FS 48

FS 64

PR000-0441+06

33 PR000-0441+08

18. SLOT TOOLS FOR EDWARDS M/CS

These types of punches and dies are computable with Edwards machines

Punch Code Size D Die Code Size D1 FS49-00090 9.00 FS65-00097 9.70 FS49-00095 9.50 FS65-00102 10.20 FS49-00100 10.00 FS65-00107 10.70 FS49-00105 10.50 FS65-00112 11.20 FS49-00110 11.00 FS65-00117 11.70 FS49-00115 11.50 FS65-00127 12.20 FS49-00120 12.00 FS65-00127 12.70 FS49-00125 12.50 FS65-00132 13.20 FS49-00130 13.00 FS65-00137 13.70 FS49-00135 13.50 FS65-00142 14.20 FS49-00140 14.00 FS65-00128 14.70 FS49-00145 14.50 FS65-00152 15.20 FS49-00150 15.00 FS65-00158 15.80 FS49-00155 15.50 FS65-00163 16.30 FS49-00160 16.00 FS65-00168 16.80 FS49-00165 16.50 FS65-00173 17.30 FS49-00170 17.00 FS65-00180 18.00 FS49-00175 17.50 FS65-00185 18.50 FS49-00180 18.00 FS65-00190 19.00 FS49-00185 18.50 FS65-00195 19.50 FS49-00190 19.00 FS65-00200 20.00 FS49-00195 19.50 FS65-00205 20.50 FS49-00200 20.00 FS65-00210 21.00 FS49-00205 20.50 FS65-00212 21.20 FS49-00210 21.00 FS65-00220 22.00 FS49-00215 21.50 FS65-00225 22.50 FS49-00220 22.00 FS65-00230 23.00

FS 49

FS 65

PR000-0441+06

34 PR000-0441+08

3. BLADES

Faik uses top quality steel to manufacture our line of shear blades. As an aftermarket supplier, we have years of experience in providing replacement shear blades for the major ironworker manufacturers. Faik inventories replacement shear blades for many Ironworkers and angle-lines. They are superior to OEM brands and competitively priced.

If you need special order sizes, our courteous sales representatives are ready to help. Special orders from Faik will be ready to be shipped as negotiated.

1. CIRCULAR BLADES

Circular Blades are considered as an important tooling for Faik where we have specialized in the circular blades for all kinds of machines.

New products can be manufactured upon customer needs and the foundation of the customer drawing is a must.

2. SPECIAL BLADES

Special Blades are blade with special design that is done according to our customer need with the demanded specifications that can comply with his machine.

Also more designs are available upon request but depending on either the customer drawing or a sample from the customer.

The sample is transformed to a technical drawing via our technical department to a sample for the customer to approve, finally to a finalized product to set an order.

Special blades have many forms and shapes and many specifications, as given below in the coming figures.

PR000-0441+06

35 PR000-0441+08

Angle Blades

Angle Blades

Bars and Round Blades

for Universal M/Cs

Cutting Blades for Angle

M/Cs

PR000-0441+06

36 PR000-0441+08

Cutting Blades

FS22-57203

Extract Blades for Angle

Universal M/C

PR000-0441+06

37 PR000-0441+08

4. MARKING TOOLS

As one of Faik missions, we found that Marking takes a huge interest of the sheet metals manufacturer. So Faik was very keen on introducing the marking products that comply with both hydraulic and eccentric machines.

1. NUMBERS & LETTERS

When Faik introduced marking for hydraulic machines we focused on both the profile and the type of the marking character. And we took a special Care of the Numbers and Letters characters.

More types of Profiles can be produced upon customer Needs and customer recommendations with all technical specifications determined by the customer. As long as the needs are determined, every detail will be easily specified then.

More examples for the marking Characters that comply with all kinds of eccentric machines.

We have more than one type for the Marking Character Set. The below table specifies each type with its dimension according to the Drawing above:

Set Name A B H L Notch Remarks

Model A 10.00 14.00 -- 20.00 o Ficep TIPO 30 (11*6)

Model B 12.00 20.00 -- 28.50 o Ficep TIPO 22 (16*8)

Model C 9.50 16.00 10.00 25.00 Manual Set

More Models can be created upon customer request.

Locking Notch

PR000-0441+06

38 PR000-0441+08

These are some live shots of the Marking Characters Mentioned above.

Marking Character Samples

PR000-0441+06

39 PR000-0441+08

2. IDENTIFICATION STAMPS

Identification stamps have been introduced recently to Faik Products upon our customer requests. The Identification stamps are simply known of 2 digits on a single punch that can be used to identify the production of a specified worker. It can be used for instance as welding stamps where we can identify the production of each welder by the stamp given upon the welded product.

Faik has introduced some new types of the welding stamps so as to give the following shapes:

1- 87 : 2 Circulated Digits

2- 87 : 2 Semi Circulated Digits

3- 87 : 2 Underline Digits

4- 87 : 2 Ordinary Digits

Also new types of Identification stamps can be produced upon customer request to satisfy his needs. And all the technical specifications are included during designing a new design. More editions can be produced. The complete set of the ID Stamp starts from the digit 00 to 99 to make a total of 100 ID Stamps in the one set.

Please find below two types of the ID Stamps with their drawing:

PR000-0441+06

40 PR000-0441+08

5. SPECIAL PARTS FOR HYDRAULIC MACHINES

Some spare parts produced by Faik are parts that originate with the machine. Where, they play an important role in the punching process or the cutting process. These spare parts are responsible for the movement of the tools used in the machines. So here by are some of the spare parts manufactured by Faik to the machines. Knowing that, we can manufacture other spare parts according to the customer need.

1. HOSING

Hosing are special spare parts for the hydraulic machines that controls the punching process. Where, it is responsible for managing the movement between the holders, the punches and the dies.

They are made of special materials and they are heat-treated with special ways to compensate their needs.

The following figure is one of Faik’s products that are compatible with Ficep angle machines.

2. HOLDERS

Holders play an important role in the punching process of the hydraulic machines. They are responsible for holding the punch and help him to penetrate the sheet metal to obtain the needed hole.

As holders have many shapes and kinds and they can be for different kinds of machine as for large type I, type II and medium type I. As well as small type holders that are compatible with Ficep A166. So here is a kind of a holder manufactured by Faik that is compatible for Ficep angle machines Large Type I.

FS20-58007

FS20-58018

PR000-0441+06

41 PR000-0441+08

3. HOLDER COUPLING NUT

Coupling nuts are nuts that are used to bond the holder with the punch in order to obtain maximum stability during the punching process. Faik has manufactured a lot of coupling nuts that are computable with angle machines.

You can find some of our products drawings that are used for Ficep angle machines and are computable for large holders type I and Type II as well as small holders for A166 Machine.

Faik has also achived different kinds of nuts which are the coupling nuts. Their function is to strengthen the bond between the holder and the punch.

Here are some our products in this field.

FS20-58042

FS20-58043

FS20-58025

Closed Center Coupling Nut

PR000-0441+06

42 PR000-0441+08

4. CUTTING BLADE HOLDER

Cutting blade holders are holders used to hold the blades inside the machine. They are realized by high quality material imported from Austria. These materials are machined to produce the blades performed by Faik that witness the birth of an Egyptian Product carrying its own Egyptian Certificate of Origin. All Machinery process that is applied to the blades is on CNC Machines where each product has its own program and its own line. They are Heat-treated and controlled well. Hardening is full hardening not case hardening

This is one of the blades performed by Faik.

FS20-58017

PR000-0441+06

43 PR000-0441+08

6. MACHINING ACCESSOIRIES

1. CLAMPS

2. CASSETTES

Cassettes are used in marking where marking letters are inserted inside the cassette to form the marking word needed.

They are manufactured to be computable with all kinds of punching machines. We have been keen to develop our products and

FS20-58039

CLAMPING For Angle M/Cs

FS20-58004 FS20-58019

FS20-58021

CLAMPING for Punch Plate

FS20-58003

PR000-0441+06

44 PR000-0441+08

CHAPTER 5| TOOLS BY MACHINING:

1. FICEP

S.N Description Faik Code Ficep Code

1 Round Punches Compatible with FICEP Small Size FS30 A21922

2 Round Punches Compatible with FICEP Medium Size FS31 A18788

3 Round Punches Compatible with FICEP Large Size FS32 A08224

4 Round Punches Compatible with FICEP X-Large Size FS33 XXXX

5 Round Punches Compatible with Small FICEP M/Cs FS34 A23912

6 Slot Punches Compatible with FICEP Medium Size FS35 A21772

7 Slot Punches Compatible with FICEP Large Size FS36 A13289

8 Slot Punches Compatible with FICEP X-Large Size FS37 XXXX

9 Round Punches Compatible with Universal M/Cs FS41 A28031

10 Round Punches Compatible with NEW Machine FS42 A22084

11 Slot Punches Compatible with Punch plate M/Cs FS43 A26220

12 Slot Punches Compatible with Angle M/Cs FS44 A13289

13 Round Dies Compatible with Small FICEP M/Cs FS50 A12688

14 Round Dies Compatible with Angle FICEP M/Cs FS51 A21578

15 Round Dies Compatible with Pallet FICEP M/Cs FS52 A26371

16 Slot Dies Compatible with Angle FICEP M/Cs FS53 A28871

17 Slot Dies Compatible with Pallet FICEP M/Cs FS54 A27352

18 Dies for Tail Punches Compatible with FICEP M/Cs FS55 XXXX

19 Various Dies Compatible with FICEP M/Cs FS56 XXXX

20 Various Dies Compatible with Filtron M/Cs FS57 XXXX

21 Round Dies for Universal M/Cs FS58 A28032

22 Slot Dies for Punch plate M/Cs FS59 A27352

23 Slot Dies for Angle M/Cs FS60 XXXX

2. KALTENBACH

S.N Description Faik Code Kaltenbach Code

1 Round Punches Compatible with Kaltenbach FS45 XXXX

2 Round Dies Compatible with Kaltenbach FS61 XXXX

PR000-0441+06

45 PR000-0441+08

3. EDWARDS

S.N Description Faik Code Edward Code

1 Round Punches Compatible with Edwards FS49 XXXX

2 Round Dies Compatible with Edwards FS65 XXXX

4. KINGSLAND

S.N Description Faik Code Kingsland Code

1 Round Punches Compatible with Kings Land FS46 XXXX

2 Round Dies Compatible with Kings Land FS62 XXXX

5. IRON WORKER

S.N Description Faik Code IW Code

1 Round Punch Compatible with IRON Work FS47 8-IWP-

2 Round Dies Compatible with IRON Work FS63 15186

6. NITTO

S.N Description Faik Code Nitto Code

1 Round Punch Compatible with Nitto Portable M/Cs FS48 XXXX

2 Round Die Compatible with Nitto Portable M/Cs FS64 XXXX

7. MUBEA

S.N Description Faik Code Mubea Code

1 Round Punches Compatible with Mubea FS25 XXXX

2 Round Die Compatible with Mubea FS66 XXXX

PR000-0441+06

46 PR000-0441+08

8. SUNRISE

S.N Description Faik Code Sun Rise Code

1 Round Punches Compatible with Sun Rise M/C FS26 9706-PR

2 Slot Punches Compatible with Sun Rise M/C FS27 XXXX

3 Round Die Compatible with Sun Rise M/C FS67 RDI

4 Slot Die Compatible with Sun Rise M/C FS68 XXXX

9. TAIWAN MACHINES

S.N Description Faik Code Taiwan Code

1 Round Punches Compatible with Taiwan M/C FS28 XXXX

2 Round Dies Compatible with Taiwan M/C FS69 XXXX

PR000-0441+06

47 PR000-0441+08

CHAPTER 6| TOOLS OPTIONALITIES

Faik can adapt stock punch and die designs to meet your specific needs and requirements.

1. PUNCH DESIGN OPTIONS

We can add extra length to the punch body or to its working length. When a job calls for punching leg up, a double body punch provides both extra length and strength. Adding a shear face reduces the tonnage required in certain applications. Keyways increase accuracy and repetitiveness.

The following Figure shows the different parts of the punch that can be modified upon customer request and according to their needs.

Punch Optional Utilities

Faik can modify some specialties in the punches as:

1- We can add extra length to the Punch either in the original length or in the working length

2- Double Body for the Punch leg 3- Shear Face of the Punch 4- Keyways

For More details please see the following diagrams:

1-Extra Length Punches 2-Double Body for Punching Leg Up

PR000-0441+06

48 PR000-0441+08

Faik also provides different kinds of punch profiles, where the customer can choose between different types of profiles of the punch shape

3-Shear Face 4-Keyways

PR000-0441+06

49 PR000-0441+08

Punches Profiles

As for the profile of the punch, you can see in the following figure that we have 13 types of different profiles. At ordering, the customer should only determine the type of the profile and the dimensions of the profile with the same variables given in the figure

PR000-0441+06

50 PR000-0441+08

2. DIE DESIGN OPTIONS

Modifications can also be made to the dies we manufacture. These include spot location, the configuration of the set screw, offset positions, and bevels.

Here is a diagram of a generic die. It will help you when discussing the design options you need with Faik.

Die Optional Utilities

As Faik presented different profiles of punches to customer, Faik also presents different styles of dies profiles

PR000-0441+06

51 PR000-0441+08

CHAPTER 7| HOW TO ORDER

Faik will be much honored to establish a co-operative relationship together and to share success stories. Faik would like to serve your needs in a satisfied way. We are ready to handle any new manufacturing case, we can help designing, or adding new ideas to some products.

Ordering from Faik depends on the case of the order as follows:

1- First order:

When ordering for the first time from Faik you need one of the following:

i. Product original Code

ii. Customer Drawing

iii. Sample to obtain its technical drawing

As also you should specify the dimensions and any technical specifications needed to be added to the product.

2- Later orders:

When ordering for the second time, you can order by:

I. Faik part number

II. Product original Code

Also more specifications can be added to the product depending on the customer needs.

3- New products:

New products are negotiable, where they can be produced if only the customer drawing is available or if there is a sample we can extract the drawing out of it.

PR000-0441+06

52 PR000-0441+08

CHAPTER 8| CONTACTS

Faik Manufacturing Company:

PLANT- FREE ZONE

Address: Industrial Free Zone, Zone No.4, Sector 46B, Badr City, Egypt.

Email: [email protected]

W/S: www.faik.com

MAIN OFFICE

Address: 7 Magless El Shaab, Cairo, Egypt.

Tel: +202-795-0487

Fax: +202-796-0523


BRANCH 1

Address: 6 Helmi Hassan Ali, 8th District, Nasr City Floor 2, Egypt.

Tel: +202-287-4122

Tel: +202-287-4412

Fax: +202-287-4407


FOREIGN TRADE DEPARTMENT

For inquiry or any information about the products

Please contact us at

Cell: +201-6738-3867


Hydraulic Cutting Tools Catalogue

Documents

Transcript of Hydraulic Cutting Tools Catalogue