HVAC Spiral Pipe Component Parts · you time and money on your next spiral pipe job. In a market...
36
HVAC Spiral Pipe Component Parts
Transcript of HVAC Spiral Pipe Component Parts · you time and money on your next spiral pipe job. In a market...
HVACSpiral PipeComponentParts
Yellow label union manufacturer of HVACSpiral Pipe component parts
Stamped Fittings® HVAC component parts will saveyou time and money on your next spiral pipe job. Ina market that is becoming more and morecompetitive, cutting costs is crucial and we havewhat you need to compete in the market. We donot manufacture everything for your spiral pipesystem, however, we can supply you with the keyparts that are readily available to make your jobmuch faster, easier and cost effective.
We continue our commitment to provide qualityproducts as well as prompt, courteous service.Please feel free to contact us if you have anyquestions or would like pricing and samples of ourHVAC products.
It’s Fast, It’s EasyIt’s Stamped Fittings®
1– Introduction®
CONSTRUCTION STANDARD:All duct and fittings are made per SMACNA’s DuctConstruction Standards (-2” W.G. / +10” W.G.)
The following table shows diameter and gauges:
Diameter
4”- 14”
16”- 26”
28”- 36”
Spiral Duct
26 ga.
24 ga.
22 ga.
FabricatedFittings
24 ga.
22 ga.
20 ga.
2
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Line®
BTOBD Page 12 BTOD2S Page 12BTOB Page 11 BTONB Page 11
CSPRB Page 10CSPR Page 104SPR Page 9E90/E901 E45/E451Page 8 Page 8
DSE145 DSEF90 DSEFU90Page 6 Page 7 Page 7 DSEF45 DSEFU45Page 7 Page 7
DSE45 NDSE90 NDSE45 DSE190Page 5 Page 5 Page 5 Page 6DSE90 Page 5
® ® ® ® ®
® ® ® ® ®
® ® ® ® ®
BTOD Page 13
DSTB Page 14
® ® ® ® ®
DSTD2S Page 15DSTNB Page 14 DSTDC6 Page 15 DSTD Page 16
® ® ® ® ®
3
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Line®
CTO Page 17 HETD Page 18
ST45 Page 21
®
CF Page 20
®
ECP Page 19HETD2S Page 18
®
CM Page 20
® ®®®
VD Page 21 C Page 22 CT Page 22
® ® ®
CROSL Page 24CROSS Page 24
® ®
CROSC Page 24
®
CRT Page 22
®
CD Page 23
®
L Page 25 LT Page 25
® ®
LRT Page 25
®
RCS Page 27 RCL Page 27 R Page 28
® ® ® ®
ER Page 28
LD Page 26 RCC Page 27
®®
ST Page 29
®
4
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Line®
DSTRT Page 31
®
D Page 33
®
D1 Page 33 BRT Page 34
®
T Page 29
®
SRT Page 29
®
STD Page 30
®
TDST Page 31
®
®
Y Page 32
®
RY Page 32
®
STO Page 34 EC Page 35
®
EP Page 35
®®
5
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®
(A)
3”
4”
5”
6”
7”
8”
9”
10”
12”
90o (R)
4.5”
6.0”
7.5”
9.0”
10.5”
12.0”
13.5”
15.0”
18.0”
DimensionsWt. Per 90o
Elbow (DSE90)0.8#
1.4#
1.8#
2.2#
3.5#
4.7#
6.1#
7.6#
10.2#
Wt. Per 90o
Elbow (NDSE90)N/A
1.4#
2.5#
3.4#
4.4#
5.4#
5.9#
6.4#
9.0#
(A)
3”
4”
5”
6”
7”
8”
9”
10”
12”
45o (R)
4.5”
6.0”
7.5”
9.0”
10.5”
12.0”
13.5”
15.0”
18.0”
Wt. Per 45o
Elbow (DSE45)0.6#
0.8#
1.0#
1.5#
1.8#
3.0#
3.5#
4.2#
6.5#
Wt. Per 45o
Elbow (NDSE45)N/A
0.8#
1.5#
2.0#
2.6#
3.2#
4.0#
4.8#
6.6#
A = DiameterR = 1-1/2 A (centerline radius)S = 2”
Flangeless elbows are continuously stitch weldedon the throat and heel from end to end (pastthe bead).
Welding Process
Materials Available
Key
n Galvanized (3”- 4”), 24 ga.n Galvanized (5”- 12”), 22 ga.n Galvaneal [paint grip] (4”), 24 ga.n Galvaneal [paint grip] (5”- 12”), 22 ga.
S
A
R
S
A
R
SSS
SSSSSSS
90o Die Stamped Flangeless ElbowGalvanized (DSE90)Galvaneal (NDSE90)
45o Die Stamped Flangeless ElbowGalvanized (DSE45)Galvaneal (NDSE45)
– Product Specifications®6
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A = DiameterR = 1A (centerline radius)S = 2”
Flangeless elbows are continuously stitch weldedon the throat and heel from end to end (pastthe bead).
Materials Available
Key
n Galvanized (4”- 10”), 24 ga.n Galvanized (12”), 22 ga.
45o Die Stamped 1.0 CLR FlangelessElbow (DSE145)
90o Die Stamped 1.0 CLR FlangelessElbow (DSE190)
(A)
4”
5”
6”
7”
8”
9”
10”
12”
90o (R)
4.0”
5.0”
6.0”
7.0”
8.0”
9.0”
10.0”
12.0”
45o (R)
4.0”
5.0”
6.0”
7.0”
8.0”
9.0”
10.0”
12.0”
DimensionsWt. Per
90o Elbow0.8#
1.0#
1.4#
2.0#
2.4#
3.0#
3.8#
7.0#
Wt. Per45o Elbow
0.5#
0.6#
1.0#
1.2#
1.6#
2.0#
2.6#
4.0#
S
A
RRRRRRR
SSSS
S
A
R
SSSSS
– Product Specifications®7
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
90o Die Stamped 20 GaugeFlanged Elbow (DSEF90)
45o Die Stamped 20 GaugeFlanged Elbow (DSEF45)
S
A
R
S
A
R
(A)
3”
4”
5”
6”
7”
8”
9”
10”
11”
12”
14”
90o
(R)
4.5”
6.0”
7.5”
9.0”
10.5”
12.0”
13.5”
15.0”
16.5”
18.0”
21.0”
45o
(R)
4.5”
6.0”
7.5”
9.0”
10.5”
12.0”
13.5”
15.0”
16.5”
18.0”
21.0”
DimensionsWt. Per
90o Elbow(Alum.)0.5#
0.7#
1.0#
1.7#
2.0#
2.8#
3.5#
4.0#
5.0#
6.2#
N/A
Wt. Per45o Elbow
0.7#
1.0#
1.5#
2.0#
2.5#
3.2#
4.0#
5.0#
6.0#
7.0#
9.0#
Wt. Per90o Elbow
1.0#
1.5#
2.0#
3.5#
5.0#
5.7#
7.2#
8.5#
10.0#
13.0#
18.0#
Wt. Per45o Elbow
(Alum.)0.2#
0.5#
0.5#
1.0#
1.2#
1.5#
1.7#
2.2#
2.7#
3.2#
4.2#
A = DiameterR = 1-1/2 A (centerline radius)S = 2”
n Available assembled or unassembled
Options Available
Materials Available
Key
n Galvanized, 20 ga.n Stainless steel 304L & 316L, 20 ga.n Aluminum 3003, 20 ga.n PVS 4x4 mill, 20 ga.
Galvanized and stainless steel are fully welded on the throat andheel by an automated welder. PVS and aluminum are assembledwith rivets and sealed with silicone. Aluminum can also be fullytig welded on the throat and heel.
Welding Process
SSS
SS
– Product Specifications®8
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
Gorelocked Elbows
A
S
A
SSS
SSS
Options Available
n Specify CLR (1.5, 1.0, etc.)n Specify Degree (15o, 22.5o, 30o, 45o,n 60o, 90o, etc.)n Up to 30o = 2 Piecen 30o+ up to 60o = 3 Piecen 60o+ up to but not including 90o = 4 Piecen 90o = 5 Piece
Key
A = DiameterS = 2”
45o 3-Piece 1.5 CLR Elbow (E45)45o 3-Piece 1.0 CLR Elbow (E451)
90o 5-Piece 1.5 CLR Elbow (E90)90o 5-Piece 1.0 CLR Elbow (E901)
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
Materials Available
– Product Specifications®9
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A
B
1-Piece Spun Reducer – Short (4SPR)WeightEach1.8#
1.8#
1.8#
1.8#
1.8#
2.1#
2.1#
2.1#
2.1#
2.1#
2.1#
2.2#
2.2#
2.2#
2.2#
2.2#
2.2#
2.4#
2.4#
2.4#
2.4#
2.4#
2.4#
(B)
12”
12”
12”
12”
12”
14”
14”
14”
14”
14”
14”
15”
15”
15”
15”
15”
15”
16”
16”
16”
16”
16”
16”
Dimensions
(A)
6”
7”
8”
9”
10”
8”
9”
10”
11”
12”
13”
9”
10”
11”
12”
13”
14”
10”
11”
12”
13”
14”
15”
WeightEach0.6#
0.6#
0.6#
0.7#
0.7#
0.7#
0.8#
0.8#
0.8#
0.8#
1.1#
1.1#
1.1#
1.1#
1.2#
1.2#
1.2#
1.2#
1.3#
1.3#
1.3#
1.3#
1.3#
1.6#
1.6#
1.6#
1.6#
(B)
4”
5”
5”
6”
6”
6”
7”
7”
7”
7”
8”
8”
8”
8”
9”
9”
9”
9”
10”
10”
10”
10”
10”
11”
11”
11”
11”
Dimensions
(A)
3”
3”
4”
3”
4”
5”
3”
4”
5”
6”
4”
5”
6”
7”
5”
6”
7”
8”
5”
6”
7”
8”
9”
7”
8”
9”
10”
A = Small end diameterB = Large end diameterS = 1-1/2”L = 1-1/2”
n Galvanized, 20 ga.
Materials Available
Key
n Sizes 4” to 16”n Male (small ends) fit into spiral pipen Bead on large end is standard
S
L
S
– Product Specifications®10
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
1-Piece Concentric Spun Reducer(CSPR/CSPRB) Weight
Each2.8#
2.8#
2.8#
2.8#
3.3#
3.3#
3.3#
3.9#
3.9#
3.9#
4.3#
4.3#
4.8#
4.8#
5.5#
5.5#
6.0#
6.0#
(B)
12”
12”
12”
12”
14”
14”
14”
16”
16”
16”
18”
18”
20”
20”
22”
22”
24”
24”
(A)
7”
8”
9”
10”
9”
10”
12”
12”
14”
15”
14”
16”
16”
18”
18”
20”
20”
22”
WeightEach1.0#
1.3#
1.3#
1.5#
1.5#
1.5#
1.8#
1.8#
1.8#
1.8#
2.0#
2.0#
2.0#
2.0#
2.2#
2.2#
2.2#
2.2#
2.6#
2.6#
2.6#
2.6#
2.6#
(B)
4”
5”
5”
6”
6”
6”
7”
7”
7”
7”
8”
8”
8”
8”
9”
9”
9”
9”
10”
10”
10”
10”
10”
(A)
3”
3”
4”
3”
4”
5”
3”
4”
5”
6”
4”
5”
6”
7”
5”
6”
7”
8”
5”
6”
7”
8”
9”
Sizes For CSPR/CSPRB Only
A
L
B
L
S
S
A = Small end diameterB = Large end diameterL = 4”S = 3”
n Galvanized, 20 ga.
Materials Available
Key
n Sizes 4” to 24”n Male (small ends) fit into spiral pipe
n Bead available on large end uponn request (CSPRB)
Options Available
– Product Specifications®11
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A = DiameterR = RadiusF = Flange length
Materials Available
Key
Options Availablen Sizes 4” to 36”n Dampers (see BTOBD spec)n Peel & stick gasket is standard on BTOB (4”- 14”)n 2” Stand-off (see BTOBD spec)n Bead or no bead
B = Overall widthH = Overall heightT = Flange thickness (gauge)
Bellmouth Take-Off (BTOB & BTONB)
n Galvanized (4”- 12”), 24 ga., stampedn Galvanized (14”- 36”), 20 ga., spun
(A)
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
18”
20”
22”
24”
26”
28”
30”
32”
34”
36”
(H)
2-1/4”
2-1/2”
4-1/4”
3-1/2”
4-1/2”
3-1/2”
4-3/4”
5-1/2”
6-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
n 4”, 5”, 7” & 9” are short BTO’sn Peel & stick gasket is not available on 16”-36”
DimensionsWeightEach0.4#
0.7#
0.8#
0.7#
1.1#
0.9#
1.5#
2.0#
3.2#
4.4#
5.4#
6.2#
7.0#
7.4#
8.0#
8.0#
10.0#
10.0#
11.0#
11.0#
(B)
6.5”
8.25”
8.5”
10.5”
11”
13”
13.5”
14.5”
17”
20”
22”
24”
26”
28”
30”
32”
34”
36”
38”
40”
(F)
1”
1”
1”
1”
1”
1”
1”
1”
1”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
(R)
.394”
.472”
.787”
1.0”
1.0”
1.0”
1.0”
1.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
(S)
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
A
S
FB
HR
– Product Specifications®12
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
Bellmouth Take-Off with Damper(BTOBD)
Materials Available
Key
Options Availablen Sizes 4” to 36”n Peel & stick gasket is standard on BTOBD (4”- 14”)n 2” Stand-off, BTOD2S (see shaft extension handlen drawing to the left)n See Volume Damper (VD) spec
A = DiameterR = RadiusF = Flange length
B = Overall widthH = Overall heightT = Flange thickness (gauge)
n Galvanized (4”- 12”), 24 ga., stampedn Galvanized (14”- 36”), 20 ga., spun
A
F
OPTION: 2” Shaft ExtensionHandle (BTOD2S)
2”
B
(A)
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
18”
20”
22”
24”
26”
28”
30”
32”
34”
36”
n 4”, 5”, 7” & 9” are short BTO’sn Peel & stick gasket is not available on 16”-36”
Dimensions
(B)
6.5”
8.25”
8.5”
10.5”
11”
13”
13.5”
14.5”
17”
20”
22”
24”
26”
28”
30”
32”
34”
36”
38”
40”
(H)
8”
8-1/2”
4-1/4”
9”
4-1/2”
9”
4-3/4”
5-1/2”
6-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
8-1/2”
WeightEach1.0#
1.2#
1.0#
2.4#
1.4#
3.0#
2.1#
2.6#
4.2#
6.4#
7.4#
8.2#
9.0#
9.4#
13.0#
13.0#
17.0#
17.0#
21.0#
21.0#
(F)
1”
1”
1”
1”
1”
1”
1”
1”
1”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
(R)
.394”
.472”
.787”
1.0”
1.0”
1.0”
1.0”
1.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
(S)
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
R
SH
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®13
Features
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring forn sealing of holesn Locking handle for adjustment ofn damper - ease of balancingn 3/8” Continuous square rod throughn dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
n 22 Gauge galvanized body
Low-Leakage Dampers
(R)
.394”
.472”
.787”
1.0”
1.0”
1.0”
1.0”
1.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
2.0”
(A)
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
18”
20”
22”
24”
26”
28”
30”
32”
34”
36”
(S)
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
(B)
6.5”
8.25”
8.5”
10.5”
11”
13”
13.5”
14.5”
17”
20”
22”
24”
26”
28”
30”
32”
34”
36”
38”
40”
(F)
1”
1”
1”
1”
1”
1”
1”
1”
1”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
1.5”
(L)
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
Dimensions
(H)
7.875”
8.25”
9.875”
9.125”
10.125”
9.125”
10.375”
11.125”
12.125”
14.125”
14.125”
14.125”
14.125”
14.125”
14.125”
14.125”
14.125”
14.125”
14.125”
14.125”
FB
L
A
S
LLL
R
H
Bellmouth Take-Off withDamper (BTOD)
– Product Specifications®14
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A1 = Branch (nominal) sizeA2 = Pipe (nominal) size
n Galvanized, 24 ga.
Materials Available
Key
Options Availablen Damper collars in 6” lengths (seen DSTDC6 spec)n Bead or no bead
R = RadiusF = Flange on pipe
R = 0.787” (4 on 4 – 6 on 20/22/24),R = 1.0” (8 on 8 – 12 on 22/24)F = 1.0” (4 on 4 – 8 on 20/22/24),F = 2.0” (10 on 10 – 12 on 22/24)S = 1-1/4” (4 on 4 – 5 on 16/24),S = 1-1/2” (6 on 6 – 12 on 22/24)
90o Die Stamped Saddle Tap(DSTB & DSTNB)
A1
A2
FR
A1
A2
H
WeightEach0.4#
0.4#
0.4#
0.4#
0.4#
0.4#
0.4#
0.7#
0.7#
0.7#
0.7#
0.7#
0.7#
0.8#
0.8#
0.7#
0.7#
0.6#
1.1#
1.3#
1.1#
1.1#
1.0#
1.8#
2.0#
1.8#
1.8#
1.7#
2.3#
2.0#
2.3#
2.1#
(A1)
4”
4”
4”
4”
4”
4”
4”
5”
5”
5”
5”
5”
5”
6”
6”
6”
6”
6”
8”
8”
8”
8”
8”
10”
10”
10”
10”
10”
12”
12”
12”
12”
Dimensions
(A2)
4”
5”
6”- 7”
8”
9”- 10”
12”- 14”
16”- 24”
5”
6”- 7”
8”- 9”
10”
12”- 14”
16”- 24”
6”
8”
10”- 12”
14”- 18”
20”- 24”
8”
10”
12”- 14”
16”- 18”
20”- 24”
10”
12”
14”- 16”
18”- 20”
22”- 24”
12”
14”- 16”
18”- 20”
22”- 24”
(H)
2”
2”
2”
2”
2”
2”
2”
2-1/8”
2-1/8”
2-1/8”
2-1/8”
2-1/8”
2-1/8”
3-1/8”
3-1/8”
3-1/8”
3-1/8”
3-1/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-3/8”
3-1/2”
3-1/2”
3-1/2”
3-1/2”
S
– Product Specifications®15
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A1 = Branch sizeA2 = Pipe sizeF = Flange on pipeH = HeightR = Radius
n Galvanized, 24 ga.
Materials Available
Key
R = 0.787” (4 on 4 – 6 on 20/22/24),R = 1.0” (8 on 8 – 12 on 22/24)F = 1.0” (4 on 4 – 8 on 20/22/24),F = 2.0” (10 on 10 – 12 on 22/24)S = 1-1/4” (4 on 4 – 5 on 16/24),S = 1-1/2” (6 on 6 – 12 on 22/24)H = 6” (where A1 is 4”- 5”)H = 7” (where A1 is 6”- 12”)
n 2” Stand-offs, DSTD2S (see shaftn extension handle drawing above)
Options Available
90o Die Stamped Saddle Tap withDamper (DSTDC6)
A1
S
A2
F
R1/2” offset
OPTION: 2” Shaft ExtensionHandle (DSTD2S)
2”
A1
A2
H
WeightEach0.8#
0.8#
0.8#
0.8#
0.8#
0.8#
0.8#
1.3#
1.3#
1.3#
1.3#
1.3#
1.3#
1.6#
1.6#
1.5#
(A1)
4”
4”
4”
4”
4”
4”
4”
5”
5”
5”
5”
5”
5”
6”
6”
6”
(A2)
4”
5”
6”-7”
8”
9”- 10”
12”- 14”
16”- 24”
5”
6”- 7”
8”- 9”
10”
12”- 14”
16”- 24”
6”
8”
10”- 12”
WeightEach1.4#
1.4#
2.1#
2.3#
2.1#
2.1#
2.0#
3.0#
3.2#
3.0#
3.0#
2.9#
3.7#
3.4#
3.7#
3.5#
(A1)
6”
6”
8”
8”
8”
8”
8”
10”
10”
10”
10”
10”
12”
12”
12”
12”
(A2)
14”- 18”
20”- 24”
8”
10”
12”- 14”
16”- 18”
20”- 24”
10”
12”
14”- 16”
18”- 20”
22”- 24”
12”
14”- 16”
18”- 20”
22”- 24”
Dimensions
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®16
Features
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring for sealing of holesn Locking handle for adjustment of damper - easen of balancingn 3/8” Continuous square rod through dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
n 22 Gauge galvanized body
Low-Leakage Dampers
Key (DSTD)
A1 = 4”, 5”, 6”, 8”, 10”, 12”A2 = Up to 24” (A2 is greater than or equal to A1)S = 2”H = see chartL = 4”
* Field installed fitting
A2
A1
S
90o Die Stamped Saddle Tap withDamper (DSTD)
HL
Dimensions
(A1)
4”
5”
6”
8”
10”
12”
(H)
7-3/4”
7-7/8”
8-3/4”
9”
9”
9-1/8”
– Product Specifications®17
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A = DiameterB = 3/4” (flange length)L = 4”S1 = 2”S2 = 1-1/4”
Materials Available
Key
Options Availablen Sizes 3” to 22”n Total length = 7-1/4”n Male (small ends) to fit into spiral pipe
Conical Take-Off (CTO)
n Galvanized (3”- 22”), 20 ga., spun
Dimensions
(L)
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
4”
(S1)
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
(B)
3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”3/4”
(A)
3”
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
18”
20”
22”
WeightEach1.0#
1.3#
1.5#
1.7#
1.8#
1.9#
2.0#
2.1#
2.2#
2.5#
2.7#
2.8#
3.3#
3.7#
(S2)
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
1-1/4”
B
A
S1
S2
L
– Product Specifications®18
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A = DiameterBxC = BaseH = HeightHET - No damperHETD - With damper
Key
Options Available
n 2” Stand-off, HETD2S (see shaftn extension handle drawing to the left)
1” wide flange aroundrectangular end
gasket seal aroundperimeter
H
A
BxC
Dimensions
(H)
9-1/4”
9-1/2”
9-1/4”
9-1/4”
9-1/4”
10-1/2”
10-1/4”
10-1/4”
10-1/2”
13”
(BxC)
10”x5”
10”x5”
12”x6”
12”x6”
12”x6”
15”x6”
16”x6-3/4”
18”x8-1/2”
20”x9-1/2”
22”x14”
(A)
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
26 Ga.Weight1.04#
1.60#
1.80#
2.00#
2.20#
2.80#
3.00#
3.60#
4.20#
6.60#
n Galvanized, 26 ga.n Complete with peel & stick neoprenen gasket
Materials Available
n Togglelock seam
Construction
High Efficiency Take-Off (HET)
High Efficiency Take-Off (HETD)
OPTION: 2” Shaft ExtensionHandle (HETD2S)
2”
1” wide flange aroundrectangular end
gasket seal aroundperimeter
H
A
BxC
– Product Specifications®19
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
End Cap/Plug (ECP)
1 3/4”
A B
A = Small end to fit in spiral pipe, - 1/8” (Plug)B = Large end to fit over spiral pipe,A = + 1/8” (Cap)
n Galvanized, 24 ga.
Materials Available
Key
n Sizes 3” to 30”
Options Available
DimensionsNominal
Size3”
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
18”
20”
22”
24”
26”
28”
30”
(B)
3-1/8”
4-1/8”
5-1/8”
6-1/8”
7-1/8”
8-1/8”
9-1/8”
10-1/8”
12-1/8”
14-1/8”
16-1/8”
18-1/8”
20-1/8”
22-1/8”
24-1/8”
26-1/8”
28-1/8”
30-1/8”
(A)
2-7/8”
3-7/8”
4-7/8”
5-7/8”
6-7/8”
7-7/8”
8-7/8”
9-7/8”
11-7/8”
13-7/8”
15-7/8”
17-7/8”
19-7/8”
21-7/8”
23-7/8”
25-7/8”
27-7/8”
29-7/8”
WeightEach.20#
.20#
.35#
.50#
.60#
.70#
.85#
1.05#
1.40#
1.80#
2.20#
2.70#
3.40#
4.00#
4.50#
5.20#
5.88#
6.60#
AAA BBBBBB
– Product Specifications®20
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
Coupling (CM/CF)
Materials Available
Key
Dimensions
(A)
3”
4”
5”
6”
7”
8”
9”
10”
12”
14”
16”
18”
20”
22”
24”
26”- 30”
(S)
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
2”
WeightEach0.8#
1.0#
1.3#
1.5#
1.7#
2.0#
2.2#
2.5#
3.0#
3.5#
3.9#
4.5#
4.9#
5.7#
6.7#
N/A
A = DiameterS = 2”
n 4” overall length is standardn Stitch welded construction
Male Coupling – For pipe, the ends are 1/8”undersize to fit inside spiral pipe. Beadis located at 2”.
Female Coupling – For pipe, the ends are 1/8”oversize to fit over spiral pipe. Reverse beadlocated at 2”.
Female Coupling
A
4”
SS
A
4”
Male Coupling
SS
AA
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
A = Branch sizeB = Pipe size
n Galvanized (24 ga.), Galvaneal, Stainlessn Steel 304 & 316, Aluminum
n SE x +/- 1/2” flange out
Materials Available
Key
Dimensions
(A)
3”
4”
5”
6”
7”
8”
9”
10”
11”
12”
13”
14”
WeightEach
0.92#
1.08#
1.23#
1.54#
1.85#
2.16#
2.77#
3.08#
3.39#
3.70#
4.01#
4.32#
Dimensions
(A)
16”
18”
20”
22”
24”
26”
28”
30”
32”
34”
36”
WeightEach
4.93#
5.55#
6.16#
6.78#
7.40#
9.94#
10.70#
11.47#
12.23#
13.00#
13.76#
Fabricated 45o Saddle Tap (ST45) Volume Damper (VD)
A
B
2”
1/2”
4”
– Product Specifications®21
Shown with hardware installed
5/16” hardware and handleare included (loose)
AA
Specs
n 4” to 12” – Galvanized, 26 ga.n 14” to 36” – Galvanized, 24 ga.
Materials Available
n 2” Stand-off with loose hardware (see specn below)n Sizes 4” to 10” (all sizes), 12” to 36” (evenn sizes only)n VD Kit which includes:n 1 - Volume Damper bladen 1 - 5/16” washern 2 - 5/16” wingnut washersn 1 - Damper handle
Options Available
A = Diameter
Key
OPTION: 2” Shaft Extension
2”
n 5/16” OD shaft extensionn 1 - 3/4” plastic sleeve(.875” OD x .75” ID x 1.75” length)
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®22
A3
A2
L
HS
A1
A1
H
A2
* Field installed fitting
A2
A1
L
H
90o Conical (C) 90o Conical Tee (CT)
90o Conical Reducing Tee (CRT)
X
S S
S
S
Key (C)
Key (CRT)
A1, A2 & A3 = DiameterA1 is greater than A3A2 is less than A1S = 2”H = 5-1/4”L = A3 + 4”X = A1 - A2 (4” minimum)
A1 & A2 = DiameterA2 is greater than A1S = 2”H = 6”
Key (CT)
A1 & A2 = DiameterA1 is greater than A2S = 2”H = 5-1/4”L = A2 + 4”
n Galvanized, Galvaneal, Stainless Steeln 304 & 316, Aluminum
Materials Available
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®23
Features
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring for sealing of holesn Locking handle for adjustment of damper - easen of balancingn 3/8” Continuous square rod through dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
n 22 Gauge galvanized body
Low-Leakage Dampers
Key (CD)
Sizes Available for A1: 4”- 10” (all sizes), 12”- 36” (even sizes only)A2 is greater than A1S = 2”H = 6”L = 4”
H
A2
* Field installed fitting
A1
LLLLL
S
90o Conical with Damper (CD)
S
H
A2A1
A3
A3S
45o angle H
A4S
A2A1
A3
A2
S
H
A1
A4
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®24
Conical Cross (CROSC) Straight Cross (CROSS)
45o Lateral Cross (CROSL)
A4
L
L
L
S
S
S
Key (All)
A1 & A2 are greater than or equal to A3 & A4L = A3 + 4”
Key (CROSS)
A1 & A2 are greater than or equal to A3 & A4L = (A3 x 1.414) + 4”
Key (CROSL)
A1, A2, A3 & A4 = DiameterA3 is greater than or equal to A4S = 2”H = 4”
A1 & A2 are greater than A3 & A4 (= 2” min.)L = A3 + 4”
Key (CROSC)
Materials Available
n Galvanized, Galvaneal, Stainless Steeln 304 & 316, Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®25
45o Lateral (L)
45o Lateral Reducing Tee (LRT)
* Field installed fitting
45o Lateral Tee (LT)
A2
A1S
H
A1
A2S
L
45o angle H
A2
A3S
L
HS 45o angle
A1
45o angle45o angle45o angle45o angle
X
S
A1 & A2 = DiameterA2 is greater than or equal to A1S = 2”H = 4”
Key (L)
A1, A2 & A3 = DiameterA1 is greater than or equal to A3A2 is less than A1S = 2”H = 4”L = A3 + 4”X = A1 - A2 (4” minimum)
Key (LRT)
A1 & A2 = DiameterA1 is greater than or equal to A2S = 2”H = 4”L = A2 + 4”
Key (LT)
Materials Availablen Galvanized, Galvaneal, Stainless Steeln 304 & 316, Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®26
Features
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring for sealing of holesn Locking handle for adjustment of damper - easen of balancingn 3/8” Continuous square rod through dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
n 22 Gauge galvanized body
Low-Leakage Dampers
Key (LD)
Sizes Available for A1: 4”- 10” (all sizes), 12”- 36” (even sizes only)A2 is greater than or equal to A1S = 2”H = 4”L = 4”
* Field installed fitting
A2
H
LA1
S
45o Lateral with Damper (LD)
Reducing Conical Cross (RCC) Reducing Straight Cross (RCS)
S
H
A2A1
A3
A4
S
A3S
45o angle H
A4S
S
A2A1
A3
A2
S
H
A1
A4
S
– Product Specifications®27
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
Reducing 45o Lateral Cross (RCL)
X
L
L
L
X
X
A1, A2, A3 & A4 = DiameterA2 is less than A1A3 is greater than or equal to A4S = 2”H = 4”X = A1 - A2 (4” min.)
Key (All)
A1 is greater than A3 & A4 (= 2” min.)L = A3 + 4”
Key (RCC)
A1 is greater than or equal to A3 & A4L = (A3 x 1.414) + 4”
Key (RCL)
A1 is greater than or equal to A3 & A4L = A3 + 4”
Key (RCS)
Materials Availablen Galvanized, Galvaneal, Stainless Steeln 304 & 316, Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®28
Concentric Reducer (R)
A2
A1
S
S
L
A2
A1
S
S
LL
Eccentric Reducer (ER)
A1 = DiameterA2 = DiameterS = 2”L = 4” if the change in diameter (A1 - A2) is lessn than 6”n If the change in diameter (A1 - A2) is greatern than or equal to 6” then L= A1 - A2.n Please specify any other length, if not then standard.
Key (R)
Materials Availablen Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
A1 = DiameterA2 = DiameterS = 2”L = (A1 - A2) x 2 + 2”n L minimum = 7- 3/4”n Please specify any other length, if not then standard.
Key (ER)
Materials Availablen Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®29
* Field installed fitting
A2
A1
S
H
A2
A1
L
S
H
Straight Tap (ST) 90o Tee (T)
S
A1 & A2 = DiameterA2 is greater than or equal to A1S = 2”H = 2”
Key (ST)
A1, A2 & A3 = DiameterA1 is greater than or equal to A3A2 is less than A1S = 2”H = 2”L = A3 + 4”X = A1 - A2 (4” minimum)
Key (SRT)
A1 & A2 = DiameterA1 is greater than or equal to A2S = 2”H = 2”L = A2 + 4”
Key (T)
90o Straight Reducing Tee (SRT)
A3
A2
L
S
HS
A1
X
Materials Available
n Galvanized, Galvaneal, Stainless Steeln 304 & 316, Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®30
Features
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring for sealing of holesn Locking handle for adjustment of damper - easen of balancingn 3/8” Continuous square rod through dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
n 22 Gauge galvanized body
Low-Leakage Dampers
Key (STD)
Sizes Available for A1: 4”- 10” (all sizes), 12”- 36” (even sizes only)A2 is greater than or equal to A1S = 2”H = 4”L = 4”
90o Straight Tap with Damper (STD)
* Field installed fitting
A2
L
S
A1
H
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®31
90o Reducing Tee with Die StampedSaddle Tap (DSTRT)
A2
A3
SS
H
A1
A1 = Up to 24” (A1 is greater than or equal to A3)A2 = Up to 24” (A2 is less than A1)A3 = 4”, 5”, 6”, 8”, 10”, 12”S = 2”H = 3/4” (where A3 = 6” or less),H = 1” (where A3 = 8” or more)L = A3 + 4”X = A1 - A2 (4” minimum)
Key (DSTRT)
A1 = Up to 24” (A1 is greater than or equal to A2)A2 = 4”, 5”, 6”, 8”, 10”, 12”S = 2”H = 3/4” (where A1 = 6” or less),H = 1” (where A1 = 8” or more)L = A2 + 4”
Key (TDST)
A1
A2
SS
H
L
H
90o Tee with Die Stamped Saddle Tap(TDST)
L X
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®32
A3A2
A1
S
A1, A2 & A3 = DiameterS = 2”
KeyY Branch (Y)
A1, A2 & A3 = DiameterA2 & A3 are less than A1S = 2”
Key
A1
S
A2 A3
Reducing Y Branch (RY)
Materials Available
Materials Available
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®33
A
Balancing Damper Section -Large End/Small End (D1)
S
L
S
L
A
Balancing Damper Section (D)A = 4”- 10” (all sizes), 12”- 36” (even sizes only)S = 2”L = 4”
Key
Materials Available
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring for sealingn of holesn Locking handle for adjustment of damper -n ease of balancingn 3/8” Continuous square rod through dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
Low-Leakage Dampers
n Galvanized (22 ga.), Galvaneal, Stainlessn Steel 304 & 316, Aluminum
A = 4”- 10” (all sizes), 12”- 36” (even sizes only)S = 2”L = 6”
Key
Materials Available
n 2” Stand-off (20 ga.)n Nylon bushings with O-ring for sealingn of holesn Locking handle for adjustment of damper -n ease of balancingn 3/8” Continuous square rod through dampern 4”- 22” Standard dampers (22 ga.)n 24”- 36” Standard dampers (20 ga.)
Low-Leakage Dampers
n Galvanized (22 ga.), Galvaneal, Stainlessn Steel 304 & 316, Aluminum
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
– Product Specifications®34
Key
S = 2”L = A + 4”X = 4” minimumA3 > A1 or A2
Order as: in, out, branch (A1, A2, A3)
Materials Available
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
Straight Take-off (STO)
Reducing Bull Head Tee (BRT)
L XX SS
A3
A1 A2
S
A
(1/2” Flange)
S
Key
A = 4”- 36”S = 2”
Materials Available
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
– Product Specifications®35
217 Lenox Avenue, Elmira Heights, NY 14903 Phone: 607.733.9988 Fax: 607.733.9967 www.stampedfittings.com
End Cap (EC)
End Plug (EP)A = Small end to fit in spiral pipeS = 2”
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
Materials Available
Key
S
AAAA
S
AAAA
A = Large end to fit over spiral pipeS = 2”
n Galvanizedn Galvanealn Stainless Steel 304 & 316n Aluminum
Materials Available
Key
