Hubbell h5263

www.hubbell-marine.com

Hubbell Marine Products

30 amp and 50 amp Cable Sets with High Intensity LED Indicator LightsHubbell now offers 30 amp and 50 amp cable sets with LED indicator lights,in both Yellow and White. The 30 amp cable sets have a bright, durable, green LED that indicates power is on. The high-intensity green LED is visibleeven in bright sunlight, and is enclosed in Hubbell's fully-molded design for superior waterproofing and exceptional durability. The 50 amp cable sets are available with TWO high-intensity LEDs. The bright green LED indicates power-on as in our 30 amp cable sets while the red LED, when lit, indicatesthere is an incorrect wiring condition at the power source that requires immediate attention. Now, you can have the very latest in (50 amp) marine cable set technology - from Hubbell - the quality leader in Marine Electrical Shore Power Products.

100 amp 3-phase 277/480 Volt Pin and Sleeve OfferingHubbell has added a line of 4 Pole, 5 Wire 100 amp 277/480 volt Pin andSleeve ship-to-shore devices. Made of yellow Zytel super tough nylon, theUV-stabilized, high-visibility housings provide increased safety and abuse-resistance and are fully watertight when properly installed and mated - providing years of reliable service.

YQ100PLUS Adapter Hubbell Marines newly redesigned 100 amp intelligent adapter can now

ely power a boats 100 amp 125/250 volt AC shore power cable set fromo 50 amp 125/250 volt AC receptacles at dockside, achieving 100 amp 0 volts - OR - from a single 50 amp 125/250 volt AC receptacle, acting as ngle adapter , and achieving 50 amp 125/250 volts, when only one suchlet is available. We have also managed to build all of this latest technology

o a much smaller, NEMA 4X watertight enclosure with LED indicator lights t check for polarity and proper wiring conditions. The newly redesigned, aller YQ100PLUS allows for safe power from dual 50 amp 125/250 volteptacles or a single 50 amp 125/250 volt receptacle - another first frombbell - the quality leader in Marine Electrical Shore Power Products.

TV-Only Ship-to-Shore InletHubbell now offers a TV-Only ship-to-shore inlet for boats that no longer require the telephone connection. With the rising use of cell phones, etc. Hubbell now makes an inlet with only the TV connection, allowing the boatmanufacturer to eliminate the cost of the internal phone wiring infrastructurethat is often times no longer needed. The TV-Only inlet is available in traditional stainless steel styling to match the stainless steel shore power inlets on board.

www.hubbell-wiring.com

New Marine ProductsN

ew M

arin

e P

rod

ucts

M

arin

e P

rod

ucts

Y

100A 480V Pin and Sleeve . . . . . . . . . . . . . . . . . . pages 18 & 19

HBLTVSS . . . . . . . . . . . page 28

30A LED Cable Sets. . . . page 750A LED Cable Sets. . . page 14

ii

Zytel is a registered trademark of E.I. DuPont.

New Marine ProductsM

arine Prod

ucts N

ew M

arine Prod

ucts

200 amp 600 volt AC Pin and Sleeve Ship-to-Shore DevicesAnother Hubbell Marine first- Hubbell Marine is proud to offer the ONLY 200 amp rated, marinized, UL Listed 200 amp ship-to-shore system. As the size of the mega-yachts continue to grow, along with the ever-increasing demandfor more power on board, Hubbell Marine continues to keep pace by offeringa full line of 200 amp fittings, back boxes and accessories that are NEMA 4X rated for superior water resistance and is fully interchangeable with UL1686 configured and listed devices as Crouse-Hinds Arktite or AppletonPowertite systems when installed in accordance with instructionsfurnished with each device.

Tamper Resistant and Weather Resistant Duplex ReceptaclesTR and WR/TR RatedHubbell Marine now offers a wide variety of receptacles and switches for indoor and outdoor applications. Available in Style Line Decorator-type and standard duplex type, these new receptacles comply with new tamper-resistant (TR) requirements and with new weather and tamper-resistant requirements (WR & TR) as defined by the 2008 National Electrical Code Article 406.8 - for use in damp and wet locations. See page iv for additionaltechnical information.

Hubbell now offers the ability to put 2 or 3 Communication Devices in a single, Style Line plateAny combination of phone (6-position jack), cable TV (F-type connector) and Category 5e modular data jacks can be assembled onto a 2-port or 3-portframeeach sold individually so you can customize them as needed. Or the highly popular phone and cable TV combination is available with the frameand matching wallplate under a single catalog number, in all the popular colors. Finallya single communications plate that can take the place of 2 or 3 platesavailable from a company you can trust for superior quality.

Hubbells Marine communication frames and connectors deliver high qualitydata and multimedia transmission to the point of connection. Hubbells 2 and 3-port Style Line frames and leading edge connections allow for customized configurations. Install Hubbells Marine communicationoffering and be assured a reliable connection.

Marine Grade Outlet Box While-In-Use Weatherproof CoversHubbell Marine now offers in-use marine grade outlet box covers thatcan accommodate Duplex, GFCI, Toggle Switch and Single Receptacles.These outlet box covers can be mounted horizontally or vertically andare made of a rugged, gray polycarbonate compound. UL listed andNEMA 3R rated, these covers meet the new National Electrical Coderequirements for while-in-use outdoor power distribution and provide maximum in-use protection.

TR and WR/TR Receptacles . . . . . . . . . . . . . . . . . . . . . page 38

Communication Devices . . . . .. . . . . . . . . . . . . . . . . . . page 41

While-In-Use Weatherproof Covers . . . . . . . . . . . . . page 42

200A Pin and Sleeve Ship-to-Shore . . . . . . . . . pages 20 & 21

iiiwww.hubbell-wiring.com

iv Dimensions in Inches (mm)www.hubbell-wiring.com

2008

NE

C R

ecep

tacl

e C

ode

Com

plia

nce

& G

ener

al In

form

atio

n M

arin

e P

rod

ucts Marine Products

2008 NEC Receptacle Code Compliance and General Information

Industrial and Commercial Wiring Devices and SystemsResidential ProductsKellems Wire Management ProductsMarine Products

National Electrical Manufacturers Association

NEMA promotes the competitiveness of itsmember companies byproviding a forum for thedevelopment of technicalstandards that are in the best interests of the industry andthe users of its products.

Since 1908, NAED has servedas the trade association forthe electrical distribution industry.To be an NAED associate member, your company must be a manufacturer or value-added reseller.

The RoHS Directive stands forthe restriction of the use of certain hazardous substances in electrical and electronic equipment.

ISO (International Organization for Standardization) is theworlds largest developer and publisher of InternationalStandards.

National Association of Electrical Distributors

Restriction of Hazardous Substances

International Organization for Standardization

IS

O 9001 : 2001

RoHS

NewTamper-Resistant Duplex ReceptaclesComply with NEC 406.11Comply with NEC 210.52

NewWeather-Resistant Duplex ReceptaclesComply with NEC 406.8(A)

These symbols appear in this catalog for easy identication.

All 125V and 250V, 15A and 20A receptacles shall be listed as weather resistant type per NEC Article 406.8, Receptacles in Damp and Wet Locations.

Interior

Ta

Washdown Areas

Marinas/Docks

Weather Resistant

All 125V, 15A and 20A receptacles shall belisted tamper-resistantreceptacles per NECArticle 406.11, Tamper-Resistant Receptaclesin Dwelling Units.

What Do These Code Requirements Mean?

Tamper-Resistant (TR)receptacles incorporateinternal mechanisms to limitaccess to energized internalcomponents.

This new TR requirementis mandatory for use indwelling unit outlets.There are also many otherapplications where theuse of TR receptacles canprovide an additional levelof electrical safety.

Weather-Resistant (WR)receptacles installed outdoors and in other wet and damp locations are subject to more demanding temperature variations, direct sunlight and unusual mechanical abuse than those in a typical dry environment. Hubbells WR receptacles are designed to withstand these environments and conditions.

Exterior

30 Amp Cable Set

100 Amp Cable Sets and Devices

50 Amp Cable Set

Twist-Lock Devices

Marine P

roducts

Table of C

ontents

HBL504NM

HBL303SSHBL303NM HBL303SSBL

HBL504RI HBL504SS HBL63CM64

HBL503NM HBL503RI HBL503SS HBL63CM60HBL77CM15HBL77CM15W

HBL77CM15HBL77CM15W

HBL26CM13HBL60CM33 HBL60CM33W

M4100B12R M4100C12R

M5100B9RM5100B7R

M5100C9R M5100C7R

M5200BS1R M5200CS1R

HBLPHTVSSHBLPHTVNM PH6624 PH7440HBLPHTVRI HBLTVSS

2 Dimensions in Inches (mm)www.hubbell-wiring.com

Shi

p-t

o-S

hore

Sel

ectio

n C

hart

- B

oats

ide

Mar

ine

Pro

duc

ts

30A125V AC2 Pole3 Wire

Pages 5-9

50A125V AC2 Pole3 Wire

Pages 10-11, 14

50A125/250V AC3 Pole4 Wire

Pages 12-14

100A125/250V AC3 Pole4 Wire

Pages 15-17

100A3Y4 Pole5 Wire

Pages 15, 18-19120/208V AC277/480V AC

200A600V AC/250V DC4 Pole5 Wire

Pages 20-21

PortableTelephoneCableTV

Pages 26-27

Marine ProductsShip-to-Shore Selection Chart - Boatside

75 Ohm TV Cable.75 Oh9 - 50' (15.2m)

- 25' (7.6m)9W - 50' (15.2m)8W - 25' (7.6m)

HBL63CM65 HBL63CM69

HBL61CM52 & HBL61CM52LED - 50' (15.2m)HBL61CM42 & HBL61CM42LED - 25' (7.6m)HBL61CM52W & HBL61CM52WLED - 50' (15.2m)HBL61CM42W & HBL61CM42WLED - 25' (7.6m)

HBL63CM61

HBL77CM16HBL77CM16W

HBL77CM16HBL77CM16W HBL63CM70 HBL77CM74WO

HBL77CM74WO

HBL61CM53 & HBL61CM53LED - 50' (15.2m)HBL61CM53W & HBL61CM53WLED - 50' (15.2m)HBL61CM43 & HBL61CM43LED - 25' (7.6m)

HBL26CM10HBL26CM11HBL60CM31HBL60CM31W

HBL74CM25WOA HBL74CM25WOAW

M4100C12 M4100R12M4100P12

M5200CS1 M5200RS1M5200PS1

PH6597TVTV97 PH6597PH6625PH7440

YC310250 - 280' (85.3m) Yellow cable only. WC310280 - 280' (85.3m) White cable only.

CW125IT5 - 125' (38.0m) One-ended cable set for winches.CW100IT5 - 100' (30.4m) One-ended cable set for winches.CS50EXT5 - 50' (15.2m) Extension cord.

CS100IT5 - 100' (30.4m) 4-WireCS75IT5 - 75' (22.8m) 4-Wire

YC306250 - 250' (76.2m) Yellow cable only.

YC406250 - 250' (76.2m) Yellow cable only.

CS1004 - 100' (30.4m) 4-WireCS754 - 75' (22.8m) 4-WireCS100IT4 - 100' (30.4m) 3-WireCS754IT4 - 75' (22.8m) 3-Wire

PH6630 - 250' (76.2m) Yellow cable only.PH6599 - 50' (15.2m)PH6598 - 25' (7.6m)PH6599W - 50' (15.2m)PH6598W - 25' (7.6m)

HBL61CM08 & HBL61CM08LEDHBL61CM08 & HBL61CM - 50' (15.2m)HBL61CM05 & HBL61CM05LED - 35' (10.7m)HBL61CM03 & HBL61CM03LED - 25' (7.6m)HBL61CM08W & HBL61CM08WLED - 50' (15.2m)HBL61CM03W & HBL61CM03WLED - 25' (7.6m)

CW125IT4 - 125' (38.0m) One-ended cable set for winches.CW100IT4 - 100' (30.4m) One-ended cable set for winches.CW754 - 75' (22.8m) One-ended cable set for winches.CS50EXT4 - 50' (15.2m) Extension cord.

M5100C9M5100C7

M5100R9 M5100R7

M5100P9M5100P7

3Dimensions in Inches (mm) www.hubbell-wiring.com

Marine P

roducts

Ship

-to-Shore S

election Chart - D

ockside

Marine ProductsShip-to-Shore Selection Chart - Dockside


Marine Products30 Ampere, 125 Volt Cable SetFeatures and Benefits

30 A

mp

ere,

125

Vol

t C

able

Set

- F

eatu

res

and

Ben

efits

M

arin

e P

rod

ucts

Exclusive copper crimp barrel terminationprovides protection against internaloverheating and burnout compared tobrass crimps. These copper crimps arethe same type used by power companies.The result: tighter connections, better conductivity and longer life.

Line-up notches to indicate:Locked - Unlocked.

Arrow indicating unlock position.

UL Listed.

Available in 25, 35 and 50 foot lengths.

Jute llers inside jacket for maximum cable exibility.Hubbell cable coils neater, lighter, lays atter.

Molded exneck adds life to cable set by helping to prevent right-angle cable damage and pullout.

Strain relief bull ring protects against stress and strainon the conductors caused by boat movement,crew trafc and rough handling.

Molded design totally encased in solid PVC material, for superior waterproong and durability.

Locking ring assures proper alignment of connector to inlet for complete contact and waterproong. Prevents accidental disengagement.

Arrow indicating lock position.

Arrow with ground symbol allowslining up with ground of receptacle.

New improved styling.

Note: Cable sets must be fully extended before using.

30A 125VNEMA L5-30R

UL/CSA

G

W

Mounting holes are 26 in. (60.3) on center.

HBLCBINM

HBL303SSO

HBL303SS

HBL303NM

HBL303SSBL


30A 125V Ship-to-Shore DevicesDescription Catalog Numbers

Stylized UV resistant non-metallic shore power inlet has white HBL303NM Centrex cover which makes unit weatherproof when completely closed. Interior has easy-to-wire terminations and is transparent for quick and easy visual inspection. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket included. Protective rear enclosure/strain relief also included.

Stylized type 316 stainless steel shore power inlet has easy to use HBL303SSBL push-button latch that makes unit watertight when fully engaged. Interior has easy-to-wire terminations and is transparent for quick and easy visual inspection. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket included. Protective rear enclosure/strain relief also included.

Traditional, stainless steel shore power inlet has new easy-to-wire HBL303SS terminations. Interior is transparent for quick and easy visual inspection. Interior is shielded from the elements by a gasketed, self-closing cover, watertight when cover is screwed in place. Mounting holes are 2.38 in. (60.3) on centers. Mounting screws and gasket included. Protective rear enclosure/strain relief also included.

Traditional stainless steel inlet housing; blank for attaching a circuit breaker HBLCBISS (not included). Mounting hardware for Carling series breakers included.

Stylized non-metallic inlet housing; blank for attaching a circuit breaker HBLCBINM (not included). Mounting hardware for Carling series breakers included.

Protective rear cover. Fits all 30A shore power inlets. SR3050** Secures to back of inlets with 3 screws which are provided.

Replacement interior for HBL303SS and 60CM61 shore power inlets. HBL303INT

Nickel plated brass adapter plate for mounting chrome plated brass HBL60CM75 shore power inlets to FS/FD box.

Traditional Stainless steel power outlet has gasketed, self-closing cover, HBL303SSO watertight when cover is screwed in place. Mounting holes are 2.38 in. (60.3) on centers. Mounting screws and gasket included.

Notes: ** Not UL/CSA. To be discontinued when present stocks are exhausted. 30A 125V Traditional Stainless Steel Inlets

IP56SUITABILITY Inlets Only.

Marine Products30 Ampere, 125 Volt Twist-Lock Devices2 Pole 3 WireShip-to-Shore Devices

Marine P

roducts

30 Am

pere, 125 Volt Tw

ist-Lock D

evices

HBL61CM08

YC310250


30A 125VNEMA L5-30R

G

W

30A 125V Shore Power Cable SetDescription Catalog Numbers

Yellow 50 ft. (15.2m) vinyl jacketed shore power cable set. #10 AWG is HBL61CM08factory pre-wired with molded-on devices. Connector end hasnon-metallic threaded sealing ring which makes inlet/connectorinterface watertight.

Same as HBL61CM08 except 35 ft. (10.7m) in length. HBL61CM05


Same as HBL61CM08 except in white. HBL61CM08W

Same as HBL61CM03 except in white. HBL61CM03W

Yellow 250 ft. (76.2m) three conductor, #10 AWG type STW, PVC jacketed YC310250portable cord with jute fillers for added flexibility. Ideal for making cable sets, extension cord, and adapters that will not mark boats deck. 250 ft. (76.2m) lengths only.

White 280 ft. (85.3m) three conductor, #10 AWG type STW, PVC jacketed WC310280portable cord with jute fillers for added flexibility. Ideal for making cable sets, extension cord, and adapters that will not mark boats deck. 280 ft. (85.3m) lengths only.

Replacement non-metallic sealing ring for 30A cable sets RPL30Pand boots. Not UL Listed.

IP56SUITABILITY

(Boatside)

Marine Products30 Ampere, 125 Volt AC Cable Sets and Bulk Cable2 Pole 3 Wire

Ship-to-Shore Devices

(Cable Sets)

30 A

mp

ere,

125

Vol

t A

C C

able

Set

s an

d B

ulk

Cab

le

Mar

ine

Pro

duc

ts

30A 125VNEMA L5-30R

UL/CSA

G

W

Bright green LED indicates Power-On.

Ergonomicstyling. Arrows line-up.

Bull ringfor added strain relief.

Exclusive crimp terminationfor longer life.


30A Shore Power Cable Set with LED Power-On IndicatorDescription Catalog Numbers

Yellow 50 ft. (15.2m) vinyl jacketed shore power cable set. #10 AWG is factory pre-wired with HBL61CM08LEDmolded-on devices. Connector end has non-metallic threaded sealing ring which makesinlet/connector interface watertight.

Same as HBL61CM08LED except 35 ft. (10.7m) in length. HBL61CM05LEDSame as HBL61CM08LED except 25 ft. (7.6m) in length. HBL61CM03LEDSame as HBL61CM08LED except in white. HBL61CM08WLEDSame as HBL61CM05LED except in white. HBL61CM05WLEDSame as HBL61CM03LED except in white. HBL61CM03WLED

Replacement non-metallic sealing ring for 30A cable sets and boots. Not UL Listed. RPL30P

IP56SUITABILITY

(Boatside)

Bright, durable, LED (green) indicates power-on. High intensity LED is visibleeven in bright sunlight. Totally molded design for superior waterproofing and durability. Exclusive copper crimp barrel terminations for tighter

connections and longer life..

Marine Products30 Ampere, Cable Set with High Intensity LED Power-On Indicator Ship-to-Shore Cable Sets

Marine P

roducts

30 Am

p C

able S

et with H

igh Intensity LED

Pow

er-On Ind

icator

HBL26CM10

HBL26CM11

HBL60CM31

HBL26CM13

HBL60CM32

HBL60CM33

30A 125VNEMA L5-30R

UL/CSA

G

W


30 A

mp

ere,

125

Vol

t Tw

ist-

Lock

D

evic

es

Mar

ine

Pro

duc

ts Marine Products30 Ampere, 125 Volt Twist-Lock Devices2 Pole 3 WireShip-to-Shore Devices


Yellow single receptacle has Rynite body and abuse resistant HBL26CM10 nylon face. IP20 SUITABILITY.

Yellow Insulgrip plug has rugged nylon housing and cord grip HBL26CM11 with range of .36.93 in. (924) that utilizes a unique offset jaws arrangement to provide secure strain relief. IP20 SUITABILITY.

Yellow Seal-Tite cover for weatherproofing HBL26CM11 plugs. HBL60CM31+ IP55 SUITABILITY. Note: Fits Insulgrip devices only.

White Seal-Tite cover for weatherproofing HBL26CM11 plugs. HBL60CM31W+ IP55 SUITABILITY. Note: Fits Insulgrip devices only.

Yellow Insulgrip connector body has rugged nylon housing and HBL26CM13 cord grip with range of .36.93 in. (924) that utilizes a unique offset jaws arrangement to provide secure strain relief.

Yellow Seal-Tite cover for weatherproofing HBL26CM13 HBL60CM33+ connector bodies when used with shore power inlets. Threaded sealing ring makes connection watertight. Also for weatherproofing HBL26CM11 plug when used with HBL303SSO power outlet. IP56 SUITABILITY. Note: Fits Insulgrip devices only.

White Seal-Tite cover for weatherproofing HBL26CM13 HBL60CM33W+ connector body when used with shore power inlets. Threaded sealing ring makes connection watertight. Also for weatherproofing HBL26CM11 plug when used with HBL303SSO power outlet. IP56 SUITABILITY. Note: Fits Insulgrip devices only.

Yellow Seal-Tite cover for weatherproofing HBL26CM13 HBL60CM32+ connector bodies when used on extension cords or adapters. IP55 SUITABILITY. Note: Fits Insulgrip devices only.

Yellow polycarbonate spring-loaded lift cover for weather- HBL74CM24WO** proofing old style 26CM10 receptacle. Meets the most stringent requirements of ULs three listing categories for weatherproof plates. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.

Same as HBL74CM24WO except gray in color. HBL7424WO** IP44 SUITABILITY.

Yellow polycarbonate spring-loaded lift cover for weather- HBL74CM25WOA** proofing HBL26CM10 receptacle. Meets the most stringent requirements of ULs three listing categories for weatherproof plates. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.

Same as HBL74CM25WOA except white in color. HBL74CM25WOAW IP44 SUITABILITY.

Same as HBL74CM25WOA except gray in color. HBL7425WOA** IP44 SUITABILITY.

Stainless steel wall plate for old 26CM10. SS725

Stainless steel wall plate for new HBL26CM10. SS720

Notes: ** See page 43 for photo. + Boots are not UL listed.

Plugs, receptacles and connectors only.

Rynite is a registered trademark of E. I. DuPont.

RPL30P

HBL26CM11V

HBL26CM11VB

HBL60CM31V

HBL26CM13V

HBL60CM33V

HBL60CM32V

30A 125VNEMA L5-30R

UL/CSA

G

W



Marine P

roducts

30 Am

pere, 125 Volt Tw

ist-Lock D

evices


Yellow Valise plug has one-piece nylon housing and assembles HBL26CM11V easily with two screws. Built-in cord grip has range of .59.93 in. (15.023.6). IP20 SUITABILITY.

Black Valise plug for use on bass boats with trolling motor. HBL26CM11VB One-piece nylon housing assembles easily with two screws. Built-in cord grip has a range of .59.93 in. (15.023.6). IP20 SUITABILITY.

Yellow Seal-Tite cover for weatherproofing HBL26CM11V HBL60CM31V+ plugs. IP55 SUITABILITY. Note: Fits Valise devices only.

Yellow Valise connector body has a one-piece nylon housing HBL26CM13V and assembles easily with two screws. Built-in cord grip has range of .59.93 in. (15.023.6). IP20 SUITABILITY.

Yellow Seal-Tite cover for HBL26CM13V connector body when HBL60CM33V+ used with shore power inlets. Threaded sealing ring makes connection watertight. IP56 SUITABILITY. Note: Fits Valise devices only.

Yellow Seal-Tite cover for weatherproofing HBL26CM13V HBL60CM32V+ connector bodies when used on extension cords or adapters. IP55 SUITABILITY. Note: Fits Valise devices only.

Replacement non-metallic sealing ring for 30A cable sets RPL30P and boots. Not UL listed.

Note: + Boots are not UL listed. Valise Plug

Plugs and connectors only.

50A 125V

W

G

HBL503NM

HBL503RI

HBL503SS

HBL63CM60

HBL77CM17

HBL77CM15


50 A

mp

ere,

125

Vol

t Tw

ist-

Lock

D

evic

es

Mar

ine

Pro

duc

ts

50A 125V Ship-to-Shore DevicesDescription Catalog NumbersStylized non-metallic shore power inlet has UV resistant white Centrex HBL503NM cover which makes unit weatherproof when completely closed. Interior has easy to wire terminals. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket included. IP56 SUITABILITY.

Stylized type 316 stainless steel shore power inlet has easy to use HBL503RI push-button latch that makes unit watertight when fully engaged. Interior has easy to wire terminals. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket included. IP56 SUITABILITY. Traditional stainless steel shore power inlet has gasketed, self-closing cover HBL503SS so interior is shielded from the elements when not in use. Watertight when cover is securely fastened. Mounting holes are 2.38 in. (60.3) on centers, and rear portion has 2.17 in. (55.1) diameter. Mounting screws and gasket included. IP56 SUITABILITY. Protective rear cover. Fits all inlets except HBL503SS. Secures to back of SR3050** inlets with 3 screws which are provided.

Replacement interior for HBL503SS and 63CM72 shore power inlets. CR16277Nickel plated brass connector body has heat resistant thermoset interior HBL63CM60 and combination metal and rubber cord grip provides superior strain relief capability. Cord grip range is .441.14 in. (11.129.0). IP20 SUITABILITY. Yellow Seal-Tite cover for connector bodies when used with 50A shore HBL77CM15+ power inlets. Threaded sealing ring makes connections watertight. IP56 SUITABILITY. White Seal-Tite cover for connector bodies when used with 50A shore HBL77CM15W+ power inlets. Threaded sealing ring makes connections watertight. IP56 SUITABILITY. Nickel plated brass cord clamp assembly with clamp range of .441.14 in. HBL77CM67 (11.129.0) provides strain relief for terminations on shore power inlets.

Yellow Seal-Tite cover for weatherproofing 50A connector bodies on HBL77CM17+ extension cords or adapters. IP55 SUITABILITY.

Notes: + Boots are not UL listed. ** Not UL/CSA. To be discontinued when present stocks are exhausted. 50A Traditional Stainless Steel Inlets


Inlets and connectors only.

50A 125V

W

G

HBL63CM61

HBL77CM16

HBL63CM70

HBL77CM74WO

SS750

HBL61CM53HBL61CM53WHBL61CM43



Yellow 50 ft. (15.2m) vinyl jacketed shore power cable set. #6 AWG type HBL61CM53STOW is completely factory pre-wired with molded-on devices.Connector end has threaded metallic sealing ring to make inlet/connector interface watertight. IP56 SUITABILITY (Y BOATSIDE).

Same as HBL61CM53 except with two high intensity LEDs. HBL61CM53LED

Same as HBL61CM53 except white. HBL61CM53W

Same as HBL61CM53W except with two high intensity LEDs. HBL61CM53WLED


Same as HBL61CM43 except with two high intensity LEDs. HBL61CM43LED

Three conductor, #6 AWG type STOW, yellow PVC jacketed portable YC306250cord with jute fillers for added flexibility. Ideal for making cable sets,extension cords, and adapters will not mark boats deck. 250 ft. (75.2m)lengths only.

Nickel plated brass plug has heat resistant thermoset interior and HBL63CM61combination metal and rubber cord grip, provides superior strainrelief capability. Cord grip range is .441.14 in. (11.129.0).IP20 SUITABILITY.

Yellow Seal-Tite cover for weatherproofing 50A plugs. IP55 SUITABILITY. HBL77CM16+

White Seal-Tite cover for weatherproofing 50A plugs. IP55 SUITABILITY. HBL77CM16W+

Single receptacle has a heat-resistant thermoset base. IP20 SUITABILITY. HBL63CM70

Yellow Valox lift cover for weatherproofing 50A receptacles. HBL77CM74WOMeets requirements of the most stringent of ULs three listingcategories for weatherproof plates. Stainless steel screws and a neoprene gasket included. For mounting to FS/FD typeweatherproof boxes. IP44 SUITABILITY.

Same as HBL77CM74WO except gray in color. IP44 SUITABILITY. HBL7774WO

Stainless steel wall plate for 50A receptacle. SS750

Notes: + Boots are not UL listed. Features and benefits on page 14.

50A Molded Cable Sets

Marine P

roducts

50 Am

pere, 125 Volt Tw

ist-Lock D

evices


Valox is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.

Plugs and receptacles only.

GW

X

Y

50A125/250V

UL/CSA

HBL504NM

HBL504RI

HBL504SS

HBL63CM64

HBL77CM17

HBL77CM15


50 A

mp

ere,

125

/250

Vol

t Tw

ist-

Lock

D

evic

es

Mar

ine

Pro

duc

ts

50A 125/250V Ship-to-Shore DevicesDescription Catalog NumbersStylized non-metallic shore power inlet has UV resistant white Centrex HBL504NM cover which makes unit weatherproof when completely closed. Interior is heat resistant thermoset material and has box lug terminals. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket included. IP56 SUITABILITY.

Stylized type 316 stainless steel shore power inlet has easy to use push- HBL504RI button latch that makes unit watertight when fully engaged. Interior is heat resistant thermoset material and has box lug terminals. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket included. IP56 SUITABILITY.Traditional stainless shore power inlet has gasketed, self-closing cover HBL504SS so that the interior is shielded from the elements when not in use. It is watertight when the cover is securely fastened. The mounting holes are 2.38 in. (60.3) on centers, and the rear portion has a 2.17 in. (55.1) diameter. Mounting screws and gasket are included. IP56 SUITABILITY. Protective rear cover. Fits all inlets except HBL504SS. SR3050** Secures to back of inlets with 3 screws which are provided.

Replacement interior for 63CM74 and HBL504SS power inlets. CR16279**Nickel plated brass connector body has a heat resistant thermoset HBL63CM64 interior and combination metal and rubber cord grip, which provides superior strain relief capability. Cord grip range is .441.14 in. (11.129.0). IP20 SUITABILITY. Yellow Seal-Tite cover for connector bodies when used with 50A shore HBL77CM15+ power inlets. Threaded sealing ring makes connections watertight. IP56 SUITABILITY. White Seal-Tite cover for connector bodies when used with 50A shore HBL77CM15W+ power inlets. Threaded sealing ring makes connections watertight. IP56 SUITABILITY. Nickel plated brass cord clamp assembly with clamp range of .441.14 in. HBL77CM67 (11.129.0) provides strain relief for terminations on shore power inlets.

Yellow Seal-Tite cover for weatherproofing 50A connector bodies on HBL77CM17+ extension cords or adapters. IP55 SUITABILITY.

Notes: ** Not UL/CSA. + Boots are not UL listed. To be discontinued when present stocks are exhausted. 50A Traditional Stainless Steel Inlets

Marine Products50 Ampere, 125/250 Volt Twist-Lock Devices3 Pole 4 WireShip-to-Shore Devices

Inlets and connectors only.

GW

X

Y

50A125/250V

UL/CSA

HBL63CM65

HBL63CM69

HBL77CM16

HBL77CM74WO

SS750

HBL61CM52HBL61CM52WHBL61CM42HBL61CM42W


Marine P

roducts

50 Am

pere, 125/250 Volt Tw

ist-Lock D

evices

50A 125/250V Ship-to-Shore DevicesDescription Catalog NumbersYellow 50 ft. (15.2m) vinyl jacketed shore power cable set, #6 AWG type HBL61CM52STOW is completely factory pre-wired with molded-on devices.The connector end has a metallic threaded sealing ring for making the inlet/connector interface watertight. IP56 SUITABILITY (BOATSIDE).

Same as HBL61CM52 except with two high intensity LEDs. HBL61CM52LED Same as HBL61CM52 except white. HBL61CM52W

Same as HBL61CM52W except with two high intensity LEDs. HBL61CM52WLED Yellow 25 ft. (15.2m) vinyl jacketed shore power cable set, #6 AWG type HBL61CM42STOW is completely factory pre-wired with molded-on devices.The connector end has a metallic threaded sealing ring for making the inlet/connector interface watertight. IP56 SUITABILITY (BOATSIDE).

Same as HBL61CM42 except with two high intensity LEDs. HBL61CM42LED Same as HBL61CM42 except white. HBL61CM42W

Same as HBL61CM42W except with two high intensity LEDs. HBL61CM42WLED Four conductor, #6 AWG type STOW, yellow PVC jacketed portable YC406250cord with jute fillers for added flexibility is ideal for making cable sets, extension cords, and adapters that will not mark the boats deck. Available in 250 ft. (76.2m) lengths only.Nickel plated brass plug has a heat resistant thermoset interior and HBL63CM65combination metal and rubber cord grip, which provides superior strain relief capability. Cord grip range is .441.14 in. (11.129.0).IP20 SUITABILITY.Yellow Seal-Tite cover for weatherproofing 50A plugs. HBL77CM16+IP55 SUITABILITY.White Seal-Tite cover for weatherproofing 50A plugs. HBL77CM16W+IP55 SUITABILITY.Single receptacle has a heat resistant thermoset base. HBL63CM69IP20 SUITABILITY.Yellow Valox lift cover for weatherproofing 50A receptacles. HBL77CM74WOMeets requirements of the most stringent of ULs three listing categoriesfor weatherproof plates. Stainless steel screws and a neoprene gasket included. For mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.Same as HBL77CM74WO except gray in color. IP44 SUITABILITY. HBL7774WOStainless steel wall plate for 50A receptacle. SS750

Notes: + Boots are not UL listed. Features and benefits on page 14.

50A Molded Cable Sets

Marine Products50 Ampere, 125/250 Volt Twist-Lock Devices3 Pole 4 WireShip-to-Shore Devices

Plugs and receptacles only.


Ergonomicstyling. Arrows

line-up.

indicates IncorrectWiring at the power source.

GW

X

Y

50A125/250V

50A 125V

W

G

Bull ringfor added strain relief.

Exclusive crimp terminationfor longer life.

IP56SUITABILITY

(Boatside)


50A Shore Power Cable Set with Two LED IndicatorsDescription Catalog Number Catalog Numbers

Yellow 50 ft. (15.2m) vinyl jacketed shore power cable set, #6 AWG type HBL61CM53LED HBL61CM52LEDSTOW is completely factory pre-wired with molded-on devices. The connector end has a metallic threaded sealing ring for makingthe inlet/connector interface watertight.

Same as HBL61CM52LED except in white. HBL61CM53WLED HBL61CM52WLEDSame as HBL61CM52LED except 25 ft. (7.6m) in length. HBL61CM43LED HBL61CM42LEDSame as HBL61CM42LED except in white. HBL61CM42WLED

50 A

mp

ere,

Cab

le S

et w

ith T

wo

Hig

h In

tens

ity L

ED

s

Mar

ine

Pro

duc

ts Marine Products50 Ampere, Cable Set with Two High Intensity LEDs: Power-On and Incorrect Wiring Indicators Ship-to-Shore Cable Sets

Two bright, durable, LEDs. GREEN indicates Power-On andRED indicates Incorrect Wiring at the power source.

High intensity LEDs are visibleeven in bright sunlight. Totally molded design for superior waterproofing and durability. Exclusive copper crimp barrel terminations for tighter

connections and longer life.

100A 3Y120/208V AC

100A125/250V AC

CS75IT4


Marine Products100 Ampere, 125/250 Volt and 3Y 120/208 Volt3, 4, and 5 Wire

Ship-to-Shore Cable Sets

100A 125/250V Ship-to-Shore Cable SetsDescription Catalog Numbers

Yellow 75 ft. (22.8m) corrosion resistant shore power cable set, 105 C rated, CS75IT4#2 AWG, 2 pole 3 wire (no neutral), STOW cable with 3 pole 4 wire, 100A 125/250V plug and connector body for use with boats with isolation transformer on board.

Same as CS75IT4 except 100 ft. (30.4m) in length. CS100IT4

Yellow 75 ft. (22.8m) corrosion resistant shore power cable set, 105 C rated, CS754#2 AWG, 3 pole 4 wire STOW cable.

Same as CS754 except 100 ft. (30.4m) in length. CS1004

Yellow 50 ft. (15.2m) corrosion resistant extension cord, 105 C rated, #2 AWG, CS50EXT43 pole 4 wire STOW cable. For mating with existing shore power cable set.

Yellow 75 ft. (22.8m) corrosion resistant one-ended (male only) power supply CW754cable, 105 C rated, #2 AWG, 3 pole 4 wire STOW cable with 3 pole 4 wiremale plug only; for use with boats using a cable winch system.

Yellow 100 ft. (30.4m) corrosion resistant one-ended (male only) power supply CW100IT4cable, 105 C rated, #2 AWG, 2 pole 3 wire (no neutral) STOW cable with 3 pole 4 wire male plug only; for use with boats with isolation transformer on board and a cable winch system.

Same as CW100IT4 except 125 ft. (38.0m) in length. CW125IT4

100A 120/208V Ship-to-Shore Cable SetsDescription Catalog Numbers

Yellow 75 ft. (22.8m) corrosion resistant shore power cable set, 105 C rated, CS75IT5#2 AWG, 3 pole 4 wire (no neutral), STOW cable with 4 pole 5 wire, 100A 120/208V plug and connector body for use with boats with isolation transformer on board.

Same as CS75IT5 except 100 ft. (30.4m) in length. CS100IT5

Yellow 50 ft. (15.2m) corrosion resistant extension cord, 105 C rated, #2 AWG, CS50EXT54 pole 5 wire STOW cable. For mating with existing shore power cable set.

Yellow 100 ft. (30.4m) corrosion resistant one-ended (male only) power supply CW100IT5cable, 105 C rated, #2 AWG, 3 pole 4 wire (no neutral) STOW cable with 4 pole 5 wire male plug only; for use with boats with isolation transformer on board and a cable winch system.

Same as CW100IT5 except 125 ft. (38.0m) in length. CW125IT5

Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of thepins and sleeves of these devices is necessary to enjoy years of optimal use.

IP67SUITABILITY

Hubbell Marine was the first to offer100 amp marine grade devices thatare considered second to none.

Hubbell developed the standard for 100 amp Pin and Sleeve devices withthe National Electric Code and theAmerican Boat and Yacht Council.

Only Hubbell offers 3, 4 and 5 wire100 amp cable sets for your shorepower requirements.

Cable sets manufactured in factory-controlled conditions using speciallycompounded cable to accommodatea full 100 amp.

Features Benefits

Factory assembled. Reliable and consistent terminations.

100 Amp pin and Rugged, watertight, sleeve devices. UL listed, AB02029 YC

compliant, corrosion resistant.

UL Listed cable. High visibility yellow, STOW cable, 105 C rated, and UL listed.

Breadth of line. Available in 75, 100,and 125 ft. lengths withand without a neutral.Fifty foot extension cords also available.

100% inspection. Each cable set is testedto ensure qualityperformance.

Marine P

roducts

100 Am

pere, 125/250 Volt and

3Y

120/208 Volt

100A125/250V AC

M4100B12R

M4100C12R

BB1001WBB1002W

BB100N


100

Am

per

e, 1

25/2

50 V

olt

Mar

ine

Pro

duc

ts

IP67SUITABILITY

Marine Products100 Ampere, 125/250 Volt3 Pole 4 WireShip-to-Shore Devices

Shore Power Inlet

100A 125/250V Ship-to-Shore DevicesDescription Catalog Numbers

Gray nylon shore power inlet has gasketed, spring-loaded cover which closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4.88 in. (123.8) on centers and rear portion has 3.94 in. (100.0) diameter. Mounting screws and gasket included.

M4100B12R

Yellow Zytel super tough nylon watertight connector body has gasketed locking ring to make inlet/connector interface watertight. Cord grip range is 1.001.94 in. (25.449.3). Note: This device mates with shore power inlet only.

M4100C12R

15 angle cast aluminum back box has corrosion resistant gray finish and top hub with 1 in. N.P.T. 100A receptacles can be mounted directly to it.

BB1001W

Same as BB1001W except threaded top hub is 2.00 in. N.P.T. BB1002W

15 angle non-metallic back box, made of high-grade engineered thermoplastic Valox to resist chemicals, abuse and U.V. rays. Has integral grounding plate, 1 in. N.P.T. hub size and 120 cu. in. capacity (hub is not included - Raco part number 1706 is recommended).

BB100N

Replacement Parts

Replacement lift cover assembly; includes cover, arm and assembly tool. CA100

Replacement locking ring and cord clamp. CC100

Replacement locking ring only. LR100

Notes: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of the pins and sleeves of these devices is necessary to enjoy years of optimal use.


FW60100

100A125/250V AC

CA100

PC100

FW60100

M4100C12

M4100R12

M4100P12


Marine P

roducts

100 Am

pere, 125/250 Volt

100A Connector Body

IP67SUITABILITY

Marine Products100 Ampere, 125/250 Volt3 Pole 4 WireShip-to-Shore Devices


Yellow Zytel super tough nylon watertight plug has gasketed locking ring to make plug/receptacle interface watertight. Cord grip range is 1.001.94 in. (25.449.3).

M4100P12

Gray nylon dockside receptacle has gasketed, spring-loaded cover. Closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4.88 in. (123.8) on centers. Mounting screws and gasket included.

M4100R12

Yellow Zytel super tough nylon watertight connector body for mating plug to connector interface on extension cords or adapters. Cord grip range is 1.001.94 in. (25.449.3). Note: It cannot be mated to the shore power inlet.

M4100C12

Back box for inlets and receptacles has 15 angle section which can be installed in any of 4 positions. Box is cast aluminum with corrosion resistant gray alkyd-based enamel finish and 1 in. N.P.T. hub which can be mounted for either top or bottom feed.

FW60100

Closure Cap for 100A plugs and connector bodies that (do not have a cap attached) have locking rings.

PC100

Replacement Parts

Replacement lift cover assembly; includes cover, arm and assembly tool. CA100

Replacement locking ring and cord clamp. CC100

Replacement locking ring only. LR100

Notes: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of the pins and sleeves of these devices is necessary to enjoy years of optimal use.


100A 3Y120/208V AC

100A 3Y277/480V AC

M5100B9R

M5100C9R

BB1001WBB1002W

BB100N

Shore Power Inlet


100

Am

per

e, 3

Y

120

/208

Vol

t an

d 3

Y

277

/480

Vol

t

Mar

ine

Pro

duc

ts

100A 3Y 120/208V and 100A 3Y 277/480VShip-to-Shore DevicesDescription Catalog Numbers

Gray nylon shore power inlet has gasketed, spring-loadedcover which closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4.88 in. (123.8) on centers and rear portion has 3.94 in.(100.0) diameter. Mounting screws and gasket included.

M5100B9R M5100B7R

Yellow Zytel super tough nylon watertight connector bodyhas gasketed locking ring to make inlet/connector interfacewatertight. Cord grip range is 1.001.94 in. (25.449.3).Note: This device mates with shore power inlet only.

M5100C9R M5100C7R

15 angle cast aluminum back box has corrosion resistant gray finish and top hub with 1 in. N.P.T. 100A receptaclescan be mounted directly to it.

BB1001W BB1001W

Same as BB1001W except threaded top hub is 2.0 in. N.P.T. BB1002W BB1002W

15 angle non-metallic back box, made of high-gradeengineered thermoplastic Valox to resist chemicals, abuseand U.V. rays. Has integral grounding plate, 1 in. N.P.T.hub size and 120 cu. in. capacity (hub is not included -Raco part number 1706 is recommended).

BB100N BB100N

Replacement Parts

Replacement lift cover assembly; includes cover, arm andassembly tool.

CA100 CA100

Replacement locking ring and cord clamp. CC100 CC100

Replacement locking ring only. LR100 LR100

Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of the pins and sleeves of these devices is necessary to enjoy years of optimal use.

IP67SUITABILITY

Marine Products100 Ampere, 3Y 120/208 Volt and 3Y 277/480 Volt4 Pole 5 WireShip-to-Shore Devices

Valoxxx is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.Zytel is a registered trademark of E.I. DuPont.

FW60100

100A 3Y120/208V AC

100A 3Y277/480V AC

CA100

PC100

FW60100

M5100C9

M5100R9

M5100P9

100A Connector Bodyody


Marine P

roducts

100 Am

pere, 3

Y 120/208 Volt and

3Y

277/480 Volt

IP67SUITABILITY

Marine Products100 Ampere, 3Y 120/208 Volt and 3Y 277/480 Volt4 Pole 5 WireShip-to-Shore Devices

100A 3Y 120/208V and 100A 3Y 277/480VShip-to-Shore DevicesDescription Catalog Numbers

Yellow Zytel super tough nylon watertight plug has gasketedlocking ring to make plug/receptacle interface watertight.Cord grip range is 1.001.94 in. (25.449.3).

M5100P9 M5100P7

Gray nylon dockside receptacle has gasketed, spring-loaded cover. Closes automatically when not in use and is watertight when securely fastened. Mounting holes are 4.88 in. (123.8) oncenters. Mounting screws and gasket included.

M5100R9 M5100R7

Yellow Zytel super tough nylon watertight connector body formaking plug to connector interface on extension cords or adapters. Cord grip range is 1.001.94 in. (25.449.3).Note: It cannot be mated to the shore power inlet.

M5100C9 M5100C7

Back box for inlets and receptacles has 15 angle section whichcan be installed in any of 4 positions. Box is cast aluminum with corrosion resistant gray alkyd-based enamel finish and 1 in. N.P.T.hub which can be mounted for either top or bottom feed.

FW60100 FW60100

Closure Cap for 100A plugs and connector bodies that (do not have a cap attached) have locking rings.

PC100 PC100

Replacement Parts

Replacement lift cover assembly; includes cover, arm andassembly tool.

CA100 CA100

Replacement locking ring and cord clamp. CC100 CC100

Replacement locking ring only. LR100 LR100

Note: Periodic cleaning and lubrication (such as LPS-1 made by Holt Lloyd Corp.) of the pinsand sleeves of these devices is necessary to enjoy years of optimal use.


M5200BS1R

M5200CS1R


200A600V AC/250V DC

200

Am

per

e, 6

00V

AC

/250

V D

C, 5

0-40

0 H

ertz

M

arin

e P

rod


200 Ampere, 600V AC/250V DC, 50-400 Hertz4 Pole 5 WireShip-to-Shore Devices

Dimensions


Gray metallic watertight shore power inlet withwingnut-secured lid for water tightness when not in use.

M5200BS1R

Gray/yellow metallic watertight connector body withlocking ring to make inlet/connector body interfacewatertight. Cord range is #1 AWG-250 MCM(0.653 max. conductor diameter).

M5200CS1R

NEMA 4X

bbell was the rst to offer a marine-ized UL listed 100 AMP Ship-To-Shore stemand now, we are the rst to offer a marine-ized, UL listed 200 AMP p-to-shore system.

Hubbells 200 AMP Ship-To-Shore System is:

NEMA 4X rated for superior water resistance. Made of copper-free aluminum with an electrostatically applied

epoxy/polyester nish. Accepts a cord range of #1 AWG 250 MCM. Pin and sleeves are made of nickel-plated Tellurium copper for

superior corrosion and heat resistance.

And

Fully interchangeable with UL 1686 congured and listed devices suchas Crouse-Hinds Arktite or Appleton Powertite (when installed inaccordance with instructions furnished with device).

M5200CS1

M5200RS1

M5200PS1

MB2003W


200A600V AC/250V DC

Marine P

roducts

200 Am

pere, 600V

AC

/250V D

C, 50-400 H

ertz

Dimensions

Marine Products200 Ampere, 600V AC/250V DC, 50-400 Hertz4 Pole 5 WireShip-to-Shore Devices


Gray/yellow metallic watertight plug with locking ring to make plug/receptacle interface watertight. Cord grip range is #1 AWG-250 MCM (0.653 max. conductor diameter).

M5200PS1

Gray metallic, watertight dockside receptacle with wing nut-secured lid for water tightness when not in use.

M5200RS1

Gray/yellow metallic watertight connector body with wing nut-secured lid for water tightness when not in use. For making plug/connector body interface on extension cords or adapters.

M5200CS1

Gray metallic Back Box for inlets and receptacles has15 angle section which can be installed in any of 4 positions, 2.0 in. N.P.T. hub.

MB2003W

Gray metallic Back Box same as above but 2 in. N.P.T. hub. MB2004W

NEMA 4X

HBL316NMHBL332NM

HBL316SSXHBL332SSX

HBL316CSW25HBL316CSWHBL332CSW

HBL316CRCHBL332CRC

HBL103RX


Inte

rnat

iona

lly R

ated

Tw

ist-

Lock

D

evic

es

Mar

ine

Pro

duc

ts

Hubbell offers the only CE certified electrical shore power system truly dedicated for boats destined for Europe and the International community. Hubbells offering of international shore power inlets are available in traditional 6QE-inch stainless steel and attractive white non-metallic types resembling our domestic offering in style and appearance but are not interchangeable with the domestic shore power system. Utilizing standard NEMA (National Electrical Manufacturers Association) configurations not typically used in the marine market, Hubbell can offer a safe and non-interchangeable 16 Amp 230 Volt system and 32 Amp 230 Volt system for use with 50 cycle systems. The system includes white power supply cables (one-end, female only) in both the 16 Amp and 32 Amp categories.

16A 230V Ship-To-Shore Power SystemDescription Catalog Numbers

Non-metallic, white, stylized, U.V. resistant shore power inlet. HBL316NM White Centrex cover makes the inlet weatherproof when closed. Mounting holes are 2.38 in. (60.3) on centers and match most existing mounting patterns. Rear enclosure strain/relief cap is provided.

Traditional, stainless steel shore power inlet has new easy-to-wire HBL316SSX terminations. Interior is transparent for quick and easy visual inspection. Interior is shielded from the elements by a gasketed, self-closing cover, watertight when cover is screwed in place. Mounting holes are 2.38 in. (60.3) on centers. Mounting screws and gasket included. Protective rear enclosure/strain relief also included.

25 ft. (7.6m) white, vinyl jacketed power supply cord with female HBL316CSW25 (boat side) end only; other end blunt cut.

50 ft. (15.2m) white, vinyl jacketed power supply cord with female HBL316CSW (boat side) end only; other end blunt cut.

Yellow locking connector replacement end for HBL316CSW25 HBL316CRC and HBL316CSW. IP20 SUITABILITY.

White Seal-Tite cover with threaded sealing ring for use with HBL103RX HBL316CRC and HBL332CRC connector bodies. IP55 SUITABILITY.

32A 230V, 50 Cycle Ship-To-Shore Power SystemDescription Catalog Numbers

Non-metallic, white, stylized, U.V. resistant shore power inlet. HBL332NM White Centrex cover makes the inlet weatherproof when closed. Mounting holes are 2.38 in. (60.3) on centers and match most existing mounting patterns. Rear enclosure/strain relief cap is provided.

Traditional, stainless steel shore power inlet has new easy-to-wire HBL332SSX terminations. Interior is transparent for quick and easy visual inspection. Interior is shielded from the elements by a gasketed, self-closing cover, watertight when cover is screwed in place. Mounting holes are 2.38 in. (60.3) on centers. Mounting screws and gasket included. Protective rear enclosure/strain relief also included.

50 ft. (15.2m) white, vinyl jacketed power supply cord with female HBL332CSW (boat side) end only; other end blunt cut.

Yellow locking connector replacement end for HBL332CSW. IP20 SUITABILITY. HBL332CRC

White Seal-Tite cover with threaded sealing ring for use with HBL103RX HBL316CRC and HBL332CRC connector bodies. IP55 SUITABILITY.

IP56SUITABILITY

Marine ProductsInternationally Rated Twist-Lock Devices16, 32 Ampere, 230 Volt

HBL316B6W

HBL316R6W

HBL316C6W

HBL316P6W

BB201W

PC320


Devices are rated in either 16A, 32A or 63A, 240V, 2 pole plus earth ( ) .

16A 240V, 2 Pole Description Catalog Numbers

Shore power inlet with mounting holes 3.13 in. (79.3) on centers HBL316B6W and 2.72 in. (69.1) diameter on rear portion.

Connector body with cord grip range of .36.83 in. (9.1-21.1). HBL316C6W

Shore power receptacle with mounting holes 3.13 in. (79.3) HBL316R6W on centers and 2.72 in. (69.1) diameter on rear portion.

Plug with cord grip range of .36.83 in. (9.1-21.1). HBL316P6W

Closure plug for HBL316B6W. Not CSA. PC320

Back box for inlets and receptacles is cast aluminum with BB201W corrosion resistant alkyd-based enamel finish and two in. N.P.T. hubs.

Feed-thru box for inlets and receptacles is cast aluminum FT202W with corrosion resistant alkyd-based enamel finish and one in. N.P.T. hubs.



Connector body with cord grip range of .451.25 in. (11.431.8). HBL332C6W

Shore power receptacle with mounting holes 3.13 in. (79.3) on HBL332R6W centers and 2.72 in. (69.1) diameter on rear portion.

Plug body with cord grip range of .451.25 in. (11.431.8). HBL332P6W


Back box for inlets and receptacles is cast aluminum with BB301W corrosion resistant alkyd-based enamel finish and one 1.0 in. N.P.T. hub.



Connector body with cord grip range of .701.45 in. (17.836.8). HBL363C6W

Shore power receptacle with mounting holes 3.88 in. (98.4) on HBL363R6W centers and 3.94 in. (88.1) diameter on rear portion.

Plug body with cord grip range of .701.45 in. (17.836.8). HBL363P6W


Back box with 1 in. N.P.T. hub. BB601W

Back box for inlets and receptacles has 15 angle section which FW60100 can be installed in any of four positions. Box is cast aluminum with corrosion resistant gray alkyd-based enamel finish and 1 in. N.P.T. hub which can be mounted for either top or bottom feed.

Marine P

roducts

Internationally Rated

Pin and

Sleeve D

evices

IP67SUITABILITY

Marine ProductsInternationally Rated Pin and Sleeve Devices16, 32, 63 Ampere, 240 Volt

UL Classified to IEC 60309-1 and 60309-2


Inte

llige

nt Y

Ad

apte

rs

Mar

ine

Pro

duc

ts Marine ProductsIntelligent Y Adapters

Intelligent Y AdaptersDescription Catalog Numbers

Adapter that permits use of 50A, 125/250V AC cable set. (HBL61CM52), YQ230with two 30A, 125V AC receptacles, HBL26CM10.

Adapter that permits use of 100A, 125/250V AC cable set. (CS754, CS1004) YQ100PLUSwith one or two 50A, 125/250V AC receptacles, 63CM69.

YQ230 - Safely powers a 50A, 125/250V AC boat from two 30A, 125V AC receptacles at dockside.

Internal Logic Senses That: Both plugs are fully engaged (i.e.,

one is not dangling loose whilethe other is plugged in) -or- theA leg plug is engaged to access a single 50A, 125/250V receptacle.

The polarity of the receptacleon the dock is correct (i.e., nomis-wiring of the hot and neutral wires).

The two receptacles are from correct phases.

Note: The YQ100PLUS Adapter must be plugged into two 50A,125/250V AC receptacles that are on the same phase to achieve 100amp, 125/250 volts power -or- theA leg 50A male into a single 50A,125/250V AC receptacle to achieve50 amp, 125/250 volts power.

Application:Problem: A boat owner with oneelectrical system on board docksin a marina that can only provide a different electrical system.

Solution: Use of the Hubbell YQ series of Intelligent Adapters cancorrect many electrical systemmismatches.

Features and Benefits: 3 pole contactor breaks both hots

and neutrals to prevent possibility of live plug when not engaged.

Combines two oppositely-phased30A, 125V receptacles to provide30 amp,125/250 volts of power.

Note: The YQ230 Adapter will only work with two 30A receptacles that are on different phases.

YQ100PLUS - Safely powers a 100A, 125/250V AC boat from two 50A 125/250V AC receptacles at dockside -or- froma single 50A 125/250V AC receptacle acting as a single adapter.


Marine P

roducts

Ad

apter S

election Guid

e

Marine ProductsAdapter Selection Guide

Boat/Cable Set Side Power Center/Dock Side Molded Straight Adapters Connector Body (Female End) Catalog Number Plug (Male End)

15A 125V, 2P 3W Straight HBL105GF* 30A 125V, 2P 3W Twist-Lock

30A 125V, 2P 3W Twist-Lock HBL61CM22 15A 125V, 2P 3W HBL61CM22W Straight Blade (lock type)

30A 125V, 2P 3W Twist-Lock HBL61CM25 20A 125V, 2P 3W Twist-Lock

50A 125V, 2P 3W Twist-Lock HBL61CM54 15A 125V, 2P 3W Straight Blade



50A 125/250V, 3P 4W Twist-Lock HBL61CM59 50A 125/250V, 3P 4W Crow Foot

30A 125V, 2P 3W Twist-Lock HBL61CM71 50A 125/250V, 3P 4W Twist-Lock

50A 125V, 2P 3W Twist-Lock HBL61CM72 50A 125/250V, 3P 4W Twist-Lock

100A 125/250V, 3P 4W Pin/Sleeve HBL61CM100 50A 125/250V, 3P 4W Twist-Lock

Molded Y Adapters

(2) 30A 125V, 2P 3W Twist-Lock HBL64CM54 50A 125/250V, 3P 4W Twist-Lock

(2) 50A 125V, 2P 3W Twist-Lock HBL64CM55 50A 125/250V, 3P 4W Twist-Lock

(2) 30A 125V, 2P 3W Twist-Lock HBL64CM56 30A 125V, 2P 3W Twist-Lock

(2) 30A 125V, 2P 3W Twist-Lock HBL64CM57 50A 125V, 2P 3W Twist-Lock

(2) 30A 125V, 2P 3W Twist-Lock HBL64CM59 50A 125/250V, 3P 4W Crow Foot

One Piece Adapters


15 or 20A 125V, 2P 3W Straight Blade HBL31CM29 30A 125V, 2P 3W Twist-Lock


15 or 20A 125V, 2P 3W Straight Blade HBL21CM29 20A 125V, 2P 3W Twist-Lock

Note: See following two pages for photographs and descriptions. * Provides GFCI Protection

HBL61CM100

HBL105GF

HBL21CM28

HBL31CM29

HBL31CM28

HBL21CM29

HBL61CM72

HBL61CM71

HBL61CM22

HBL61CM54

HBL61CM55

HBL61CM56

HBL61CM59

HBL61CM25


Molded Straight AdaptersDescription Catalog NumbersPermits use of 20A 125V Twist-Lock locking type plug with HBL21CM28 15 or 20A 125V straight blade receptacle. IP20 SUITABILITY.Permits use of 15A or 20A 125V straight blade plug with HBL21CM29 20A 125V Twist-Lock locking type receptacle. IP20 SUITABILITY. Permits use of 30A 125V Twist-Lock locking type plug with HBL31CM28 15 or 20A 125V straight blade receptacle. IP20 SUITABILITY. Permits use of 15A or 20A 125V straight blade plug with HBL31CM29 30A 125V Twist-Lock locking type receptacle. IP20 SUITABILITY. Permits use of 30A 125V cable set, HBL61CM08, with 15 or HBL61CM22 20A 125V straight blade receptacle. Anchor locking screw on plug when screwed down resists pullout of the cable set. Same as HBL61CM22, except white. HBL61CM22WPermits use of 30A 125V cable set, HBL61CM08, with HBL61CM25 20A 125V Twist-Lock receptacle, HBL23CM10. Permits use of 50A 125V cable set, HBL61CM53, with HBL61CM54 15 or 20A 125V straight blade receptacle. Permits use of 30A 125V cable set, HBL61CM08, with HBL61CM55 50A 125V Twist-Lock receptacle, HBL63CM70. Permits use of 50A 125V cable set, HBL61CM53, with HBL61CM56 30A 125V Twist-Lock receptacle, HBL26CM10. Permits use of 50A 125/250V Twist-Lock locking type HBL61CM59 cable set, HBL61CM52, with 50A 125/250V crow foot straight blade receptacle HBL7962. Permits use of 30A 125V cable set, HBL61CM08, with HBL61CM71 50A 125/250V Twist-Lock receptacle, HBL63CM69. Permits use of 50A 125V cable set, HBL61CM53, with HBL61CM72 50A 125/250V Twist-Lock receptacle, HBL63CM69. Permits use of 15A 125V 3 wire straight blade plug with HBL5273L 15 or 20A 125V 2 wire straight blade receptacle.Permits a 100 amp 125/250 volt cable set to plug into a HBL61CM100 single 50 amp 125/250 volt outlet.Permits use of 15A straight blade plug with 30A 125V HBL105GF Twist-Lock receptacle; with GFCI protection. Notes: UL listed. Adapters do not provide overcurrent protection. Adapters do not provide GFCI protection except HBL105GF. The male plug end (50A 125/250V) has a blade removed and the blade slot filled with epoxy. Omitting the blade ensures achieving 125V safely.

Mol

ded

Str

aigh

t A

dap

ters

M

arin

e P

rod


Molded Straight Adapters

IP65SUITABILITY

HBL64CM54

HBL64CM55

HBL64CM57

HBL64CM56

HBL64CM59


Marine P

roducts

Mold

ed Y

Ad

apters

Marine ProductsMolded Y Adapters

Molded Y AdaptersDescription Catalog Numbers

Permits use of two 30A 125V cable sets, HBL61CM08, with HBL64CM54 one 50A 125/250V receptacle, HBL63CM69.

Permits use of two 50A 125V cables sets, HBL61CM53, with HBL64CM55 one 50A 125/250V receptacle, HBL63CM69.

Permits use of two 30A 125V cable sets, HBL61CM08, with HBL64CM56 one 30A 125V receptacle, HBL26CM10.

Permits use of two 30A 125V cable sets, HBL61CM08, with HBL64CM57 one 50A 125V receptacle, HBL63CM70.

Permits use of two 30A 125V cable sets, HBL61CM08, with HBL64CM59 one 50A 125/250V crow-foot straight receptacle, HBL7962.

Notes: The adapters shown on this page are not UL Listed because of the nature of adapters with their variety of ratings. Adapters do not provide overcurrent protection. Adapters do not provide GFCI protection except HBL105GF.

IP65SUITABILITY

PPPPH6598W

PH7440

HBLPHTVSS

HBLPHTVNM

PH6625

PH6624

HBLTVSS


Marine ProductsTelephone and Cable TV DevicesShip-to-Shore Devices

Tele

pho

ne a

nd C

able

TV

Dev

ices

M

arin

e P

rod

ucts

Telephone and Cable TV Ship-to-Shore DevicesDescription Catalog Numbers

Stylized non-metallic inlet provides telephone and cable TV HBLPHTVNMconnections in one unit. UV resistant white Centrex cover makes unit weatherproof when completely closed. Mounting holes are 2.38 in. (60.3) on centers and match existing mounting patterns. Mounting screws and gasket provided. IP56 SUITABILITY.

Stylized Type 316 stainless steel inlet provides telephone and HBLPHTVRI cable TV connections in one unit. Easy to use push-button latchmakes unit watertight when fully engaged. Mounting holes are2.38 in. (60.3) on centers and match existing mounting patterns.Mounting screws and gasket provided. IP56 SUITABILITY.

Traditional stainless steel inlet provides connections for telephone HBLPHTVSSand cable TV in one unit. Connections can be used individually ortogether. Gasketed cover is self-closing so interior is shielded from the elements when not in use. Watertight when cover isscrewed in place. Mounting holes are 2.38 in. (60.3) on centers.Mounting screws and gasket included. IP56 SUITABILITY.

Same as HBLPHTVSS above except no phone. HBLTVSS

Replacement int. for PH6594TV and HBLPHTVSS series inlets. CR16914

Factory pre-wired 50 ft. (15.2m) telephone cable set. Uses 3 PH6599conductor, #16 AWG type SJTO, yellow vinyl cord for marine and recreational vehicle applications. IP55 SUITABILITY.

Same as PH6599 except white. PH6599W

Same as PH6599 except 25 ft. (7.6m) in length. PH6598

Same as PH6598 except white. PH6598W

Black locking type plug for telephone cable sets or adapters. PH6625

Black locking type connector body used on telephone cable sets PH6624or adapters.

Yellow Seal-Tite cover for weatherproofing PH6624 connector PH7440body on cable sets when connecting to an inlet and for weather-proofing PH6625 plug. IP55 SUITABILITY.

Yellow Seal-Tite cover for weatherproofing PH6624 connector PH7499body when used on extension cords or adapters. IP55 SUITABILITY.

Note: To be discontinued when present stocks are exhausted.

Centrex is a registered trademark of LANXESS Corporation.

PH6597TV

TV97

PH6597

PH6596

PH6619

PH6595

TV99 TV99WTV98TV98W


Marine P

roducts

Telephone and

Cab

le TV D

evices

Marine ProductsTelephone and Cable TV DevicesShip-to-Shore Devices

Telephone and Cable TV Ship-to-Shore DevicesDescription Catalog Numbers

Black polycarbonate combination telephone/TV outlet with PH6597TV spring-loaded weatherproof lift cover. Can be wired for telephone service only or for telephone and MATV/CATV services in one FS/FD box in both marinas and RV parks. Can be padlocked to prevent unauthorized use.

Black polycarbonate telephone outlet has gasketed, spring- PH6597 loaded lift cover for weatherproofing. Designed for mounting to FS/FD type weatherproof boxes (like PH6619) in both marinas and RV parks.

Black polycarbonate cable TV outlet has coax connector TV97 and gasketed, spring-loaded lift cover for weatherproofing. Designed for mounting to FS/FD type weatherproof boxes (like PH6619) in both marinas and RV parks.

Black polycarbonate telephone outlet has gasketed, spring- PH6596 loaded lift cover for weatherproofing. Can be used to retrofit old style telephone outlets of Pauluhn Manufacturing Company (2833 and 2843) in both marinas and RV parks.

Black non-metallic FS box with in. threaded hubs used for PH6619 mounting phone and TV outlets and PH6595 recreational vehicle inlet (see PH6621 for mounting box on recreational vehicle). Cord connector included for strain relief and to maintain watertight integrity of box when cable is used. PVC adapter also included for connection of PVC conduit to box.

Stainless steel bracket for mounting PH6619 FS box to PH6621 recreational vehicles when used with PH6595 inlet.

Black polycarbonate RV inlet for telephone connection only. PH6595 Has spring-loaded, gasketed weatherproof lift cover designed for mounting to FS/FD type weatherproof boxes.

50 ft. (15.2m) yellow jacketed ship-to-shore TV cable set is the TV99 industry standard 75 Ohm, RG59-U with male plugs on both ends. Adapter included for a quick, slip-on connection to inlet on boat.

Same as TV99 except white. TV99W

Same as TV99 except 25 ft. (7.6m) in length. TV98

Same as TV98 except white. TV98W

IP55SUITABILITY

HBL74CM25WOA

HBL328DCR

HBL328DCC

HBL6080

HBL328DCP


30 A

mp

ere,

28

Volt

DC

Rat

ed

Mar

ine

Pro

duc

ts

Electric Fishing Reel DevicesHubbell has a DC rated electrical system designed specifically for larger electric fishing reel systems.

Up until now, larger electric fishing reel systems typically utilized conventional 30 Amp AC rated devices since an appropriately rated DC system was not available.

The system features a corrosion resistant plug, connector body and receptacle and can be used along with a Hubbell outlet box and weatherproof cover plate to complete the installation. These devices are all rated at 28 volts DC and are applicable for all 12, 24 and 32 volt DC fishing reel systems. The devices are UL listed and CSA certified. All devices are made of high-visibility yellow nylon that is impact resistant and U. V. stabilized for longer life. Also, the contacts are nickel plated for corrosion resistance.

Electric Fishing Reel DevicesDescription Catalog Numbers

Yellow locking single receptacle with abuse-resistant face. HBL328DCR Can be mounted in Hubbell box HBL6080 and used with HBL74CM25WOA weatherproof plate.

Yellow locking plug has rugged nylon housing and rear dust HBL328DCP seal to keep dust and foreign matter out.

Yellow locking connector body has rugged, nylon housing HBL328DCC and rear dust seal to keep dust and foreign matter out.

AccessoriesDescription Catalog Numbers

Black phenolic type FD (deep) weatherproof box has two HBL6080 in. (19.1) I.P.S. molded-in knockouts. 4.56 in. H x 2.94 in. W x 3.25 in. D (115.9 x 74.6 x 82.6) and has 22 cubic inch capacity.

Spring-loaded lift cover, for weatherproofing HBL74CM25WOA HBL328DCR outlet. Yellow in color.

Same as HBL74CM25WOAW except white in color. HBL74CM25WOAW

Same as HBL74CM25WOAW except gray in color. HBL7425WOA

Marine Products30 Ampere, 28 Volt DC RatedElectric Fishing Reel Devices

M11SP

M123SP

M21SP

M223SP

MSB1

MH11

MHB11

M11SP M11LRGSP M11LTR MR11SP MR123LRSP


Typical Applications Description Catalog Numbers Key

Lights, bilge blower, bilge Single pole, single throw. M11SP 1 pump(s), accessories On/Off. M11LRSP 2 M11LRGSP 2 M11LTR 3 MR11SP 4 MR11LRSP 5

Horn, starter, winches, Single pole, single throw. M11MSP* 1 gauges Momentary On/Off. M11LTRM 3 MR11MSP 4

Bilge pumps, speed selector, Single pole, double throw. M123SP 1 lights, navigation lights On/Off/On. M123LTR 3 MR123SP 4 MR123LRSP 5

Bilge pumps Single pole, double throw. M123MSP 1 Momentary On/Off/On. MR123MSP 4

Trim Tabs Single pole, double throw. M123MMSP 1 Momentary On/Off/Momentary On. MR123MMSP 4

Lights, accessories Double pole, single throw. M21SP 1 On/Off. MR21SP 4

Navigation lights, wipers, Double pole, double throw. M223SP 1 dual fuel tanks On/Off/On. MR223SP 4 MR223LRSP 5

Navigation lights, windlass Double pole, double throw. M223JSP 1 On/Off/On (with jumper).

Winches, trim tabs, Double pole, double throw. M223MMSP 1 dual fuel tanks Momentary On/Off/Momentary On. MR223MMSP 4

Provides positive seal against Black silicone rubber boot bonded MSB1 moisture, oil, etc. Fits any to brass nut. non-lighted toggle switch.

For remote operation of horn. Push-button horn switch with 56:O in. MH11 long nickel plated brass mounting stem. Terminals are .25 in. spade.

Fits MH11 horn switch. Black push-button (horn) boot. MHB11

KEY CHART

Marine P

roducts

12 Volt DC

Rated

Sw

itches

1. Toggle switch Fits panels up to in. thick when not using the back-up nut provided; fits panels up to 6QEin. thick when using the back-up nut. Requires a in. mounting hole.

2. Lighted toggle switch Built-in pilot light (R=red, G=green) for night vision. Same panel specs as 1.

3. Lighted-tip toggle switch Red pilot light visible in tip of toggle only. Same panel specs as 1.

4. Rocker switch Requires a 1 in. high x (6 in. wide rectangular opening.

5. Lighted rocker switch Built-in pilot light for night vision. Same panel specs as 4.

Marine Products12 Volt DC Rated SwitchesPanel Mount Toggle and Rocker Switches

HBL47CM15 HBL47CM16

HBL52CM21

HBL60CM23

HBL47CM29C

HBL60CM24

HBL47CM20C

HBL47CM00

15A 125VNEMA L5-15R

UL/CSA


15 A

mp

ere,

125

Vol

t A

C T

wis

t-Lo

ck

Dev

ices

M

arin

e P

rod


15 Ampere, 125 Volt AC Twist-Lock Devices2 Pole 3 Wire

15A 125V AC Twist-Lock DevicesDescription Catalog Numbers

Yellow duplex receptacle has heat resistant body. IP20 SUITABILITY. HBL47CM00

Yellow Valox spring-loaded lift cover for weatherproofing HBL52CM21 duplex receptacles. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes. IP20 SUITABILITY.

Same as HBL52CM21 except white in color. HBL52CM21W

Same as HBL52CM21 except gray in color. HBL5221

Same as HBL52CM21 except for mounting to standard boxes. HBL52CM22

Same as HBL52CM22 except gray in color. HBL5222

Yellow Insulgrip plug has rugged nylon housing and detachable HBL47CM20C cord grip with range of .30.69 in. (7.517.4) that utilizes a unique offset jaws arrangement to provide secure strain relief.

Short yellow Seal-Tite cover for weatherproofing HBL47CM20C HBL60CM23+ Insulgrip plug when used with receptacles or connector bodies. Also can be used to weatherproof HBL47CM29C Insulgrip connector body when used with HBL47CM16 flanged inlet. IP55 SUITABILITY.

Yellow Insulgrip connector body has rugged nylon housing and HBL47CM29C detachable cord grip with range of .30.69 in. (7.517.4) that utilizes a unique offset jaws arrangement to provide secure strain relief.

Yellow Seal-Tite cover for weatherproofing HBL47CM29C HBL60CM24+ Insulgrip connector body when used on extension cords and adapters. IP20 SUITABILITY.

Panel mount flanged outlet has heat resistant melamine interior HBL47CM15 and stainless steel casing. IP20 SUITABILITY.

Panel mount flanged inlet has heat resistant melamine interior HBL47CM16 and stainless steel casing. IP20 SUITABILITY.

Three conductor, #14 AWG type STW, yellow PVC jacketed YC314250 portable cord has jute fillers for added flexibility and is ideal for making cable sets, extension cords and adapters as it will not mark the boats deck. Available in 250 ft. (76.2m) length only.

Note: + Boots are not UL listed.


HBL74CM23WO

HBL61CM64

HBL52CM66C

HBL52CM69C

HBL52CM66V

HBL52CM69V

HBL52CM80C

HBL52CM62HBL52CM61

15A 125VNEMA L5-15R

UL/CSA


Marine Products15 Ampere, 125 Volt AC Straight Blade Devices2 Pole 3 Wire

15A 125V AC Straight Blade DevicesDescription Catalog NumbersYellow single receptacle features Rynite body and abuse HBL52CM61resistant nylon face.Yellow corrosion resistant duplex receptacle. Use where HBL52CM62salt or other corrosive elements are a problem.Same as HBL52CM62 except ivory. HBL52CM62I

Yellow Insulgrip plug has rugged nylon housing and detachable HBL52CM66Ccord grip with range of .23.72 in. (5.818.3) that utilizes a unique offset jaws arrangement for secure strain relief.Yellow Seal-Tite cover for weatherproofing straight blade HBL60CM17+Insulgrip plugs, HBL52CM66C and HBL53CM66C, when used with receptacles and connector bodies. Can also be used toweatherproof Insulgrip connector bodies when mating withflanged inlets. IP55 SUITABILITY. Not UL or CSA.Note: For Insulgrip devices only.Yellow Insulgrip connector body has rugged nylon housing and HBL52CM69Cdetachable cord grip with range of .23.72 in. (5.818.3) that utilizes a unique offset jaws arrangement for secure strain relief.Yellow Seal-Tite cover for weatherproofing straight blade HBL60CM18+Insulgrip connector bodies, HBL52CM69C and HBL53CM69C,on extension cords and adapters. IP55 SUITABILITY. Not UL or CSA.Note: For Insulgrip devices only.Yellow Valise plug has one-piece nylon housing that assembles HBL52CM66Veasily with two screws. Built-in cord grip has range of .22.66 in.(5.616.8).Yellow Valise connector body has one-piece nylon housing that HBL52CM69Vassembles easily with two screws. Built-in cord grip has range of .22.66 in. (5.616.8).Yellow Insulgrip plug with anchor locking screw to prevent HBL52CM80Caccidental pull-out. The plug is locked into the receptacle when the screw is turned down so the head is flush with the plug surface. The cord grip range is .30.69 in. (7.517.4).UL Recognized Component.Compact gray nylon panel mount inlet ideal for bass boat battery HBL61CM64charging connection. Has gasketed spring-loaded lift cover forweatherproofing front and neoprene boot for weatherproofing rear. Will accept both 15A 125V and 20A 125V 2 pole 3 wire straightblade connector bodies.Same as HBL61CM64 except black in color. HBL61CM64BKYellow Valox spring-loaded lift cover for weatherproofing HBL52CM21duplex receptacles. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes.Same as HBL52CM21 except gray in color. HBL5221Same as HBL52CM21 except for mounting to standard boxes. HBL52CM22Same as HBL52CM22 except gray in color. HBL5222Yellow Valox spring-loaded lift cover for weatherproofing HBL74CM23WOsingle straight blade receptacles. Stainless steel screws andneoprene gasket included. For mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY.Same as HBL74CM23WO except gray in color. HBL7423WONote: + Boots are not UL listed. * Refer to page iv for TR and WR descriptions.

Marine P

roducts

15 Am

pere, 125 Volt A

C S

traight Blad

e DevicesRynite is a registered trademark of E. I. DuPont.

Valoxxx is a trademark of SABIC Innovative Plastics, acquired from General Electric Company.

IP20SUITABILITY

*

*

HBL74CM25WOA

HBL23CM10

HBL23CM11

HBL60CM31

HBL26CM13

HBL60CM32 HBL23CM11V

HBL60CM31VHBL60CM32V

20A 125VNEMA L5-20R

UL/CSA

G

W


20A 125V Twist-Lock DevicesDescription Catalog NumbersYellow single receptacle has Rynite body and abuse resistant nylon face. HBL23CM10 IP20 SUITABILITY. Yellow polycarbonate spring-loaded lift cover for weather-proofing HBL74CM25WOA HBL23CM10 receptacle. Meets the most stringent requirements of ULs three listing categories for weatherproof plates. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY. Same as HBL74CM25WOA except gray in color. HBL7425WOASame as HBL74CM25WOA except white in color. HBL74CM25WOAWYellow Insulgrip plug has rugged nylon housing and cord grip with range of HBL23CM11 .36.93 in. (924) that utilizes a unique offset jaws arrangement to provide secure strain relief. IP20 SUITABILITY. Yellow Seal-Tite cover for weatherproofing HBL26CM11 or HBL23CM11 HBL60CM31+ plugs. IP55 SUITABILITY. Note: Fits Insulgrip devices only.Same as HBL60CM31 except white in color. HBL60CM31W+Yellow Insulgrip connector body has rugged nylon housing and cord HBL23CM13 with range of .36.93 in. (924) that utilizes a unique offset jaws arrangement to provide secure strain relief. IP20 SUITABILITY.Yellow Seal-Tite cover for weatherproofing HBL26CM13 or HBL23CM13 HBL60CM32+ connector bodies when used on extension cords or adapters. IP55 SUITABILITY. Note: Fits Insulgrip devices only.Yellow vinyl Seal-Tite cover for weatherproofing HBL23CM13V or HBL60CM32V+ HBL26CM13V connector bodies. IP55 SUITABILITY. Note: Fits Valise devices only. Yellow Valise plug has one-piece nylon housing, assembles easily with HBL23CM11V two screws. Built-in cord grip has range of .33.72 in. (8.318.2). IP20 SUITABILITY. Yellow Seal-Tite cover for weatherproofing HBL23CM11V or HBL60CM31V+ HBL26CM11V plugs. IP55 SUITABILITY. Note: Fits Valise devices only. Three conductor, #12 AWG type STW, yellow PVC jacketed portable cord YC312250 with jute fillers for added flexibility. Ideal for making cable sets, extension cords and adapters as will not mark boats deck. Available in 250 ft. (76.2m) length only.


20 A

mp

ere,

125

Vol

t Tw

ist-

Lock

D

evic

es

Mar

ine

Pro

duc

ts

Plugs, receptacles and connectors only.


Marine Products20 Ampere, 125 Volt Twist-Lock Devices2 Pole 3 Wire

HBL52CM21 HBL74CM23WO HBL61CM65

20A 125VNEMA L5-20R

UL/CSA

HBL53CM61

HBL53CM62

HBL53CM66C

HBL53CM69C

HBL60CM18HBL60CM19

HBL60CM17


Marine P

roducts

20 Am

pere, 125 Volt A

C S

traight Blad

e Devices

20A 125V AC Straight Blade DevicesDescription Catalog NumbersYellow Insulgrip plug has rugged nylon housing and detachable cord HBL53CM66C grip with range of .23.72 in. (5.818.3) that utilizes unique offset jaws arrangement to provide secure strain relief. IP20 SUITABILITY.Yellow Insulgrip connector body has rugged nylon housing and cord HBL53CM69C grip with range of .23.72 in. (5.818.3) that utilizes unique offset jaws arrangement for secure strain relief. IP20 SUITABILITY. Yellow Seal-Tite cover for weatherproofing straight blade Insulgrip HBL60CM18+ connector bodies, HBL52CM69C and HBL53CM69C, on extension cords and adapters. IP55 SUITABILITY. Note: For Insulgrip devices only. Yellow closure plug used with HBL60CM18 long Seal-Tite cover to HBL60CM19+ prevent water from entering front of device when not in use. IP55 SUITABILITY.Yellow Seal-Tite cover for weatherproofing straight blade Insulgrip plugs, HBL60CM17+ HBL52CM66C and HBL53CM66C, when used to mate receptacles and connector bodies. Can also be used with Insulgrip connector bodies when mating with flanged inlets. IP55 SUITABILITY. Note: For Insulgrip devices only.Yellow duplex receptacle has Rynite body. Receptacle accepts both 20A HBL53CM62 125V and 15A 125V 2 pole 3 wire straight blade plugs. IP20 SUITABILITY. Single version of HBL53CM62 duplex yellow receptacle. IP20 SUITABILITY. HBL53CM61Compact gray nylon panel mount outlet ideal for electric trolling motors HBL61CM65 and reel applications. Features gasketed spring-loaded lift cover for weatherproofing front and neoprene boot for weatherproofing rear. Accepts both 20A 125V and 15A 125V 2 pole 3 wire straight blade plugs. IP55 SUITABILITY.Yellow polycarbonate spring-loaded lift cover for weatherproofing HBL52CM21 duplex receptacles. Stainless steel screws and neoprene gasket included for mounting to FS/FD type weatherproof boxes. IP20 SUITABILITY. Not CSA.Same as HBL52CM21 except white in color. HBL52CM21WSame as HBL52CM21 except gray in color. HBL5221Same as HBL52CM21 except for mounting to standard boxes. HBL52CM22Same as HBL52CM22 except gray in color. HBL5222Yellow polycarbonate spring-loaded lift cover for weatherproofing HBL74CM23WO single straight blade receptacles. Stainless steel screws and neoprene gasket included. For mounting to FS/FD type weatherproof boxes. IP44 SUITABILITY. Not CSA. Same as HBL74CM23WO except gray in color. HBL7423WO



Marine Products20 Ampere, 125 Volt AC Straight Blade Devices2 Pole 3 Wire

GFP6C15MGFP25C15M

GFP315A

HBL5200

GFT2G

GFP15M


Por

tab

le G

roun

d F

ault

Circ

uit

Inte

rrup

ters

and

Tes

ters

M

arin

e P

rod


Portable Ground Fault Circuit Interrupters and Testers

Portable Ground Fault Circuit Interrupters (GFCIs) These UL Listed portable GFCIs have been designed to protect people from line-to-ground electrical shock hazards which may develop from faulty appliance, tools or defective portable cords. If a ground fault does occur and the leakage level exceeds 4 to 6 milliamperes, the GFCI unit quickly acts to protect the user by opening the circuit, thus interrupting the power supply and limiting the duration of any electrical current flow. After tripping, the module is reset by pushing a button on its face. A test button allows the user to test that the GFCI is in working order. Note: GFCI devices will not protect against overloads or short circuits.

Portable Ground Fault Circuit Interrupters and TestersDescription Catalog Numbers

Hubbell h5263

Documents

Transcript of Hubbell h5263