Hsp sani english

Copyright © 2013 HS Protect I Head Office Geraardsbergsesteenweg 258 9400 Ninove Belgium I [email protected]

HS PROTECT – SANI is an air-drying peelable coating designed to protect sanitary fittings from damage during construction, transportation and storage. It can easily be applied with an airless spray gun, paintbrush or paint roller.

HS PROTECT – SANI protects everyone's interests!

The protective foil protects bathtubs, sinks and shower cubicles against scratches and dirt during construction. It can also be applied to porcelain, glass fiber and enamel surfaces. At the same time, our product helps protect expensive and easily damaged stainless steel taps and other nonporous materials.

HS PROTECT – SANI protects your materials from damaging on the construction site.

More often than not, sanitary fittings need to be replaced because they acquire stains and/or scratches during construction.

More often than not, a pricy bathtub gets used as a garbage bin during construction.

More often than not, a slater works standing in the bathtub, dirty shoes and all.

To prevent these events from damaging your bathtub and shower cabinets, you can now coat your sanitary installations with an extra layer of protection.

HS PROTECT – SANI will save you time, money and a lot of problems!

Start using HS PROTECT – SANI and discover this inexpensive and easy-to-use product and its effective results.

Remove the protective foil on completion, and offer your customer sanitary fittings that are of showroom quality.

Are you planning on installing an expensive designer bathtub, shower or whirlpool in acryl? We offer you a coating solution designed specifically for soft surfaces:

HS PROTECT – SANI+ offers exclusive and softer surfaces a durable protection without damaging the shiny surface or color of these delicate materials.


Benefits Overview:

ü water-based, non-flammable and eco-friendly

ü easy to apply/remove and highly cost-effective

ü prevents damage (tubs should be provided with an extra layer)

ü benefits your customer relations

ü no cleaning needed after removal of the film

ü can be disposed of as regular construction waste

Ready in 2 steps: apply and remove

NO MORE BULLSHIT

APPLY REMOVE

1 2


TECHNICAL DATA SHEET • In General

HS PROTECT – SANI is a revolutionary liquid coating that forms a temporary peelable film when dry to protect a variety of sanitary fittings.

HS PROTECT – SANI protects substrates against weathering, scratches, filthiness (e.g. paint or mortar splashes) and corrosive chemicals that could damage them. Both interior and exterior use is possible.

• Field of Application:

HS PROTECT – SANI was developed specifically for the protection of sanitary fixtures and other nonporous materials. It can also be used on mirrors and stainless steel.

Should not be applied to untreated wood or porous surfaces.

We advice to use HS PROTECT – SANI + for all acrylic surfaces

• Specifics:

Appearance liquid, blue

Fixed Content Approximately 40%

Density 1.05

Resistance / Durability HS PROTECT – SANI is weatherproof and UV-resistant for a maximum period of 12 months outdoors. It will not detach unless removed by peeling.

Drying time HS PROTECT – SANI will be surface-dry in approximately 30

minutes depending on the weather conditions. It takes 24 hours to completely dry the foil.

Health and safety Nonflammable in both liquid and dry state.

Local Suction: It is recommended to minimize the molar concentration during spray application.


The use of protective clothing is advised. Avoid skin and eye contact. In case of: CONTACT WITH EYES: Rinse with water for at least 15 minutes.

INHALATION: Inhale fresh air. CONTACT WITH SKIN: Rinse with water and soap. INGESTION: Remove from stomach by induced vomiting or aspiration. Seek medical attention. RELEASED/SPILLED MATERIAL: Absorb with inert material (e.g. sand, soil, etc.). Caution: Liquid emulsion can be very slippery. WATER DISPOSAL: In accordance with state, local, and federal requirements/measures.

• Application Guidelines:

Application Temperature Between 5°C and 35°C = Ideal temperature.

Manual Application Apply by means of a paint roller. A minimal layer thickness of 200

micron in dry condition, 400 in wet, is recommended. Too thin of a layer will be difficult to remove.

Mechanical Application Apply by means of a spray gun. Avoid spray-mist edges, so that the overall thickness of the layer is not compromised.

Cleaning Equipment can be cleaned with warm water. Add detergent if necessary.

Repairs In case of damage to the HS PROTECT – SANI film, the film can

easily be replaced by applying a new layer of HS PROTECT –

SANI above the existing one. The two layers will merge.

Removal The temporary film HS PROTECT – SANI can easily be removed with one move. At temperatures below 5 degrees Celsius, the film may become brittle, which, in turn, will hamper the removal process.

Remarks The freshly applied HS PROTECT – SANI film should be protected against rain for a 24-hour period. Once dry, the HS PROTECT –

SANI film layer becomes thermoplastic.


• Transport – Packaging – Storage: Store at room temperature in its closed original packaging. Screen from freezing temperatures. Limit open-air exposure to avoid bacterial growth.

Allowed storage: maximum 12 months in non-opened original packaging.

In order to ascertain the suitability of the surfaces to be treated with the HS PROTECT products, the application of the product to a pre-established test area is mandatory. Our company will not be held responsible for damages that may result from

erroneous application of the HS PROTECT products.

Hsp sani english

Documents

Transcript of Hsp sani english