HOW TO USE THIS INSTALL GUIDE - Amazon S3...Amplifi er location: Left end of dash Note: The amplifi...
86
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners. WARNING Pressing the printer icon or “quick printing” this document will print all of the guides in this compilation. Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle. Print only the pages for your vehicle using the advanced options in the Print menu. Install your DSR1 module according to the guide for your vehicle. HOW TO USE THIS INSTALL GUIDE 1 2 3 SELECT VEHICLE PRINT PAGES NEEDED
Transcript of HOW TO USE THIS INSTALL GUIDE - Amazon S3...Amplifi er location: Left end of dash Note: The amplifi...
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
WARNING Pressing the printer icon or “quick printing” this document will print
all of the guides in this compilation.
Open the Bookmarks menu and find your vehicle OR scroll down until you find the install guide for your vehicle.
Print only the pages for your vehicle using the advanced options in the Print menu.
Install your DSR1 module according to the guide for your vehicle.
HOW TO USE THIS INSTALL GUIDE1
2
3
SELECT VEHICLE PRINT PAGES NEEDED
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDECHRySLER 200
2015-2016ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 200 2015-2016
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 200 2015-2016
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 200 2015-2016
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 200 2015-2016
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Mid (+)
White/Black Left Front Mid (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Mid (+)
Gray/Black Right Front Mid (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Mid (+)
Green/Black Left Rear Mid (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Mid (+)
Purple/Black Right Rear Mid (-)
RIGHT REAR 2Purple Subwoofer 2 (+)
Purple/Red Subwoofer 2 (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black n/a
Black/White n/a
SUB 2Black Right Rear Tweeter (+)
Black/Red Right Rear Tweeter (-)
SUB 3Black n/a
Black/Yellow n/a
Amplifi er location: Right end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDECHRySLER 300
2012-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2012-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2012-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2012-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2012-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Left Rear Tweeter (+)
Green/Red Left Rear Tweeter (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Right Rear Tweeter (+)
Purple/Red Right Rear Tweeter (-)
CENTER 1 Orange Center Speaker (+)
Orange/Black Center Speaker (-)
SUB 1Black Subwoofer 1 (+)
Black/White Subwoofer 1 (-)
SUB 2Black Subwoofer 2 (+)
Black/Red Subwoofer 2 (-)
SUB 3Black Subwoofer 3 (+)
Black/Yellow Subwoofer 3 (-)
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDECHRySLER 300
2018-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2018-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2018-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2018-2019
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
CHRYSLER 300 2018-2019
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Left Rear Tweeter (+)
Green/Red Left Rear Tweeter (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Right Rear Tweeter (+)
Purple/Red Right Rear Tweeter (-)
CENTER 1 Orange Center Speaker (+)
Orange/Black Center Speaker (-)
SUB 1Black Subwoofer 1 (+)
Black/White Subwoofer 1 (-)
SUB 2Black Subwoofer 2 (+)
Black/Red Subwoofer 2 (-)
SUB 3Black Subwoofer 3 (+)
Black/Yellow Subwoofer 3 (-)
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE CHALLENGER
2015-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2015-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2015-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2015-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2015-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Left Rear Mid (+)
Green/Red Left Rear Mid (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Right Rear Mid (+)
Purple/Red Right Rear Mid (-)
CENTER 1 Orange Center Speaker (+)
Orange/Black Center Speaker (-)
SUB 1Black Subwoofer 1 (+)
Black/White Subwoofer 1 (-)
SUB 2Black Subwoofer 2 (+)
Black/Red Subwoofer 2 (-)
SUB 3Black n/a
Black/Yellow n/a
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE CHALLENGER
2018-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2018-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2018-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2018-2019
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHALLENGER 2018-2019
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Left Rear Mid (+)
Green/Red Left Rear Mid (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Right Rear Mid (+)
Purple/Red Right Rear Mid (-)
CENTER 1 Orange Center Speaker (+)
Orange/Black Center Speaker (-)
SUB 1Black Subwoofer 1 (+)
Black/White Subwoofer 1 (-)
SUB 2Black Subwoofer 2 (+)
Black/Red Subwoofer 2 (-)
SUB 3Black n/a
Black/Yellow n/a
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE CHARGER
2012-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2012-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2012-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2012-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2012-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Left Rear Speaker (+)
Green/Red Left Rear Speaker (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Right Rear Speaker (+)
Purple/Red Right Rear Speaker (-)
CENTER 1 Orange Center Speaker (+)
Orange/Black Center Speaker (-)
SUB 1Black Subwoofer 1 (+)
Black/White Subwoofer 1 (-)
SUB 2Black Subwoofer 2 (+)
Black/Red Subwoofer 2 (-)
SUB 3Black Subwoofer 3 (+)
Black/Yellow Subwoofer 3 (-)
Amplifi er location: Left side of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE CHARGER
2018-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2018-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2018-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2018-2019
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE CHARGER 2018-2019
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Left Rear Speaker (+)
Green/Red Left Rear Speaker (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Right Rear Speaker (+)
Purple/Red Right Rear Speaker (-)
CENTER 1 Orange Center Speaker (+)
Orange/Black Center Speaker (-)
SUB 1Black Subwoofer 1 (+)
Black/White Subwoofer 1 (-)
SUB 2Black Subwoofer 2 (+)
Black/Red Subwoofer 2 (-)
SUB 3Black Subwoofer 3 (+)
Black/Yellow Subwoofer 3 (-)
Amplifi er location: Left side of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE DURANGO
2014-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2014-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2014-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2014-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2014-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 2 (+)
Green/Red Subwoofer 2 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Subwoofer 1 (+)
Purple/Red Subwoofer 1 (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black Right Rear Tweeter (+)
Black/White Right Rear Tweeter (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Center Speaker (+)
Black/Yellow Center Speaker (-)
Amplifi er location: Left side of cargo area
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE DURANGO
2018-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2018-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2018-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2018-2019
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE DURANGO 2018-2019
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 2 (+)
Green/Red Subwoofer 2 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Subwoofer 1 (+)
Purple/Red Subwoofer 1 (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black Right Rear Tweeter (+)
Black/White Right Rear Tweeter (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Center Speaker (+)
Black/Yellow Center Speaker (-)
Amplifi er location: Left side of cargo area
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEDODGE JOURNEy
2011-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE JOURNEY 2011-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE JOURNEY 2011-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE JOURNEY 2011-2019
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
DODGE JOURNEY 2011-2019
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Subwoofer 2 (+)
Purple/Red Subwoofer 2 (-)
CENTER 1 Orange n/a
Orange/Black n/a
SUB 1Black n/a
Black/White n/a
SUB 2Black n/a
Black/Red n/a
SUB 3Black n/a
Black/Yellow n/a
Amplifi er location: Center console
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEJEEP CHEROkEE
2014-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Tweeter (+)
Green/Black Left Rear Tweeter (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Tweeter (+)
Purple/Black Right Rear Tweeter (-)
RIGHT REAR 2Purple Subwoofer 2 (+)
Purple/Red Subwoofer 2 (-)
CENTER 1 Orange Left Rear Speaker (+)
Orange/Black Left Rear Speaker (-)
SUB 1Black n/a
Black/White n/a
SUB 2Black Right Rear Speaker (+)
Black/Red Right Rear Speaker (-)
SUB 3Black Center Speaker (+)
Black/Yellow Center Speaker (-)
Amplifi er location: Right end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEJEEP GRAND CHEROkEE
2014-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2014-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 2 (+)
Green/Red Subwoofer 2 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Subwoofer 1 (+)
Purple/Red Subwoofer 1 (-)
CENTER 1 Orange Left Rear Speaker (+)
Orange/Black Left Rear Speaker (-)
SUB 1Black Right Rear Speaker (+)
Black/White Right Rear Speaker (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Center Speaker (+)
Black/Yellow Center Speaker (-)
Amplifi er location: Left side of cargo area
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDEJEEP GRAND CHEROkEE
2018-2019ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2018-2019
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2018-2019
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2018-2019
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
JEEP GRAND CHEROKEE 2018-2019
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 2 (+)
Green/Red Subwoofer 2 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Subwoofer 1 (+)
Purple/Red Subwoofer 1 (-)
CENTER 1 Orange Left Rear Speaker (+)
Orange/Black Left Rear Speaker (-)
SUB 1Black Right Rear Speaker (+)
Black/White Right Rear Speaker (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Center Speaker (+)
Black/Yellow Center Speaker (-)
Amplifi er location: Left side of cargo area
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDERAM 1500 2013-2017
ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2013-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2013-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2013-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2013-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Center Speaker (+)
Purple/Red Center Speaker (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black Right Rear Tweeter (+)
Black/White Right Rear Tweeter (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Subwoofer 2 (+)
Black/Yellow Subwoofer 2 (-)
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDERAM 1500
2018ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2018
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2018
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2018
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 1500 2018
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Center Speaker (+)
Purple/Red Center Speaker (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black Right Rear Tweeter (+)
Black/White Right Rear Tweeter (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Subwoofer 2 (+)
Black/Yellow Subwoofer 2 (-)
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDERAM 2500 & 3500
2013-2017ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2013-2017
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2013-2017
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Confi gure the 2 pin connectors on the aCH2 T-harness as shown on the wiring diagram.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 1:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 2:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
1
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2013-2017
Automotive Data Solutions Inc. © 2020 4
1
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAM
STEP 1
STEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
WHITEWHITE
GREENGREEN
GRAYGRAY
BLUE
PURPLEPURPLE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2013-2017
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Center Speaker (+)
Purple/Red Center Speaker (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black Right Rear Tweeter (+)
Black/White Right Rear Tweeter (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Subwoofer 2 (+)
Black/Yellow Subwoofer 2 (-)
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
OPTIONAL ACCESSORIES
PROGRAMMED FIRMWAREADS-DSR1-CHR03
PRODUCTS REQUIREDRockford Fosgate DSR1iDatalink Maestro aCH2 Installation Harness
INSTALL GUIDERAM 2500 & 3500
2018ENABLE A SEAMLESS AFTERMARKET AMPLIFIER INSTALLATION,
WITHOUT CHANGING YOUR RADIO.
NOTICE: Automotive Data Solutions Inc. (ADS) recommends having this installation performed by a certified technician. Logos and trademarks used here in are the properties of their respective owners.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2018
Automotive Data Solutions Inc. © 2020 2
WELCOME
NEED HELP?
Congratulations on the purchase of your iDatalink Maestro / Rockford Fosgate DSR1 Amplifi er replacement solution. You are now a few simple steps away from enjoying your new car amplifi er. Before starting your installation, please ensure that your module is programmed with the correct fi rmware for your vehicle and that you carefully review the install guide.
TABLE OF CONTENTS
Installation Instructions 3
Wiring Diagram 4
Vehicle Wire Reference Chart 5
1 866 427-2999
maestro.idatalink.com/supportwww.12voltdata.com/forum
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2018
Automotive Data Solutions Inc. © 2020 3
INSTALLATION INSTRUCTIONS STEP 1
• Remove the factory amplifi er (refer to wire chart for amplifi er location).
• Insert the resistor pack and confi gure the 2 pin connectors on the aCH2 T-harness as shown in the wiring diagram.
Note 1:
If the resistor pack is not included, use four 500 ohm resistors, Put each resistor across the wires of the white, gray, green, and purple 2 pin connectors.
STEP 2• Connect the factory amplifi er harnesses to the aCH2
T-harness.
STEP 3• Connect the wires from the aCH2 T-harness to the
aftermarket amplifi er.
Note 2:
If you are running your own speaker wires from the amplifi er to the speakers, this step is not necessary.
Note 3:
The amplifi er output colors and labels on the aCH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, see the wiring chart.
• Plug the RCA cables in the aftermarket amplifi er.
STEP 4• Connect all the harnesses to the DSR1 module.
CHIME ADJUSTMENTThis is only needed when the vehicle supports chimes (ex:
Parking assist, Blind spot detection, Lane sense, etc.).
• Set the audio source to OFF (if there is no way to turn the
radio OFF, set the source to AUX).
• The OEM radio will have 3 volume settings for parking
assist (Low/Med/High), it is recommended to choose
medium volume.
• Activate any chime (ex: rear parking assist).
• Adjust the chime volume using the volume knob.
For technical assistance call 1-866-427-2999 or e-mail “[email protected]”. Visit us at “maestro.idatalink.com/support” and “www.12voltdata.com/forum/”
2
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2018
Automotive Data Solutions Inc. © 2020 4
2
LEFT FRONT 1
RIGHT FRONT 1
LEFT REAR 1
RIGHT REAR 1
LEFT FRONT 2
RIGHT FRONT 2
LEFT REAR 2
RIGHT REAR 2
SUB 1
SUB 2
SUB 3
CENTER 1
LEFT FRONT OUT 1LEFT FRONT OUT 1
RIGHT FRONT OUT 2RIGHT FRONT OUT 2
LEFT SPARE OUT 3LEFT SPARE OUT 3
RIGHT SPARE OUT 4RIGHT SPARE OUT 4
LEFT REAR OUT 5LEFT REAR OUT 5
RIGHT REAR OUT 6RIGHT REAR OUT 6
LEFT SUB OUT 7LEFT SUB OUT 7
RIGHT SUB OUT 8RIGHT SUB OUT 8
CONNECTIONS NOT REQUIRED
WIRING DIAGRAMSTEP 2STEP 3
aCH2 T-HARNESS
FACTORY AMPLIFIERHARNESSES
AMPLIFIER
WIRES FROMVEHICLE
BLUE
REDN.C.
N.C.
WHITEWHITE/BLACK
GRAYGRAY/BLACK
GREENGREEN/BLACK
PURPLE/BLACK
GRAY/RED
WHITE/REDGRAY
GREENGREEN/RED
PURPLE
WHITE
PURPLE
PURPLE/REDBLACK
BLACK/WHITEBLACK
BLACK/RED
BLACKBLACK/YELLOW
ORANGEORANGE/BLACK
STEP 4DSR1 MODULE
RCA CABLES
STEP 1
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
WHITEWHITE
GREENGREEN
GRAYGRAY
PURPLEPURPLE
RESISTOR PACK (1)
(1) NOTE: IF THE RESISTOR PACK IS NOT INCLUDED, USE FOUR 500 OHM RESISTORS,PUT EACH RESISTOR ACROSS THE WIRES OF THE WHITE, GRAY, GREEN, AND PURPLE 2 PIN CONNECTORS.
ADS-DSR1-CHR02B-AR maestro.idatalink.com
RAM 2500 & 3500 2018
Automotive Data Solutions Inc. © 2020 5
VEHICLE WIRE REFERENCE CHART
T-Harness Wires Vehicle Wires
WireTag
WireColor Speaker Wire Description
LEFT FRONT 1 White Left Front Speaker (+)
White/Black Left Front Speaker (-)
LEFT FRONT 2White Left Front Tweeter (+)
White/Red Left Front Tweeter (-)
RIGHT FRONT 1 Gray Right Front Speaker (+)
Gray/Black Right Front Speaker (-)
RIGHT FRONT 2Gray Right Front Tweeter (+)
Gray/Red Right Front Tweeter (-)
LEFT REAR 1 Green Left Rear Speaker (+)
Green/Black Left Rear Speaker (-)
LEFT REAR 2Green Subwoofer 1 (+)
Green/Red Subwoofer 1 (-)
RIGHT REAR 1 Purple Right Rear Speaker (+)
Purple/Black Right Rear Speaker (-)
RIGHT REAR 2Purple Center Speaker (+)
Purple/Red Center Speaker (-)
CENTER 1 Orange Left Rear Tweeter (+)
Orange/Black Left Rear Tweeter (-)
SUB 1Black Right Rear Tweeter (+)
Black/White Right Rear Tweeter (-)
SUB 2Black n/a
Black/Red n/a
SUB 3Black Subwoofer 2 (+)
Black/Yellow Subwoofer 2 (-)
Amplifi er location: Left end of dash
Note: The amplifi er output colors and labels on the AR-CH2 T-harness do not correspond to the vehicle. For vehicle specifi c wiring designation, follow this wiring chart.
