How to use auto code reader turn off check engine light alert
-
Upload
autoobdtools -
Category
Automotive
-
view
2.376 -
download
1
Transcript of How to use auto code reader turn off check engine light alert
AutoOBDToolsLearning CenterAutoOBDTools offical blog is used to share auto obd diagnostic tools
knowledge
How to use auto code reader turn offcheck engine light alert
By OBDBLOG64Gpp2u5 on July 1, 2011 | Leave a response
When a check engine light alert appears,AutoOBDTools.com tell you how to use auto codereader to fix it.
diagnostic link connector under the driver's-side dash
1. Locate the code reader receptacle under the dash. This is the connection to yourcar’s computer. It’s usually under the dash on the driver’s side under the steeringwheel.
auto code reader plug
2. Plug the end of the code reader’s cable into the receptacle. As soon as you plug it in,it will turn on automatically and try to read the car’s status. The code reader’s displaywill display the word, Read.
Search
Search this site...
Categories
Auto Code Reader
auto key programmer
car repair term
OBDII PDF E-BOOK Download
Archives
July 2011 (34)
June 2011 (1)
Recent Comments
steersags on What is OBDII(On-
Board Diagnostic)
slimmingmethodsonline on What is
OBDII(On-Board Diagnostic)
buylegalsteroids on What is
OBDII(On-Board Diagnostic)
Blogroll
AutoOBDTools
You are here: Home / Auto Code Reader / How to use auto code reader turn off check engine light alert
http://blog.autoobdtools.com/auto-code-reader/how-to-use-auto-code-reader-turn-off-check-engine-light-alert/
BMW INPA OBD2 INTERFACE
Price: 237.00$
U581 LIVE DATA OBD2 EOBD
Scanner Can-Bus Code
Reader Price: 100.00$
VOLVO VIDA DICE 2010D
Diagnostic Tool
Price: 310.00$
BMW AK90 Key Programmer
for all BMW EWS
Price: 499.00$ 449.00$
32MB CARD FOR GM TECH2
Price: 169.99$
Free Shipping 711
Programmerr
Price: 129.00$
BMW 20pin Cable for BMW
GT1
Price: 66.99$
S.1279 Module of PPS2000
Lexia-3 Citroen Peugeot
Price: 36.00$
auto code reader plugged in
3. Turn the ignition on to accessory power. Don’t crank the engine. Accessory power isthe when you turn the key in the ignition to the notch where the radio is on and theseatbelt chime starts ringing. You must turn on the power within 10 or 15 seconds ofconnecting the code reader or the code reader will display ERROR and after a fewseconds, repeat the cycle of trying to read the car’s status again
4. After you turn the ignition switch to accessory power, the code reader will readwhatever code your car’s computer is sending. In the case of the picture at left, onlythe numerical error code is displayed. The owner would then need to refer to theinstruction manual that came with the code reader in order to determine what thecode represented. For the purpose of this tutorial, we’re assuming that we alreadyknow that the code represents something that isn’t critical and all we want to do isturn off the check engine light.
5. Press the Erase button twice. Check engine light is off. Disconnect code reader andturn off ignition. You just saved yourself at least $50 by doing it yourself!
POSTED IN Auto Code Reader
TAGGED Auto Code Reader, check engine light alert, turn off check engine light alert
Copyright © 2011 AutoOBDTools Learning Center. Powered by WordPress and Trending.
Name * Email *
POST COMMENT
← PREVIOUS NEXT →
Leave a Reply
Website
Comment