How to replace spark plugs on NISSAN QASHQAI I J10
Transcript of How to replace spark plugs on NISSAN QASHQAI I J10
![Page 1: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/1.jpg)
How to replace spark plugs onNISSAN QASHQAI I J10
VIDEO TUTORIAL
This replacement procedure can be used for: NISSAN LIVINA / GRAND LIVINA (L10, L11) 1.6, NISSAN MICRA C+C III (K12) 1.6160 SR, NISSAN MICRA III (K12) 160 SR, NISSAN NOTE (E11, NE11) 1.6, NISSANNV200 / EVALIA Bus 1.6 16V (M20, M20M), NISSAN NV200 Box Body / Estate1.6 16V (M20, M20M), NISSAN QASHQAI / QASHQAI +2 I (J10, NJ10, JJ10E) 1.6,NISSAN TIIDA Hatchback (C11) 1.6, NISSAN TIIDA Saloon (SC11) 1.6
The steps may slightly vary depending on the car design.
WWW.AUTODOC.CO.UK 1–28
Important!
![Page 2: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/2.jpg)
REQUIRED TOOLS:
WWW.AUTODOC.CO.UK 2–28
Torque wrench
Spark plug socket # 16
Drive socket # 8
Drive socket # 10
Ratchet wrench
Round-nose pliers
Flat screwdriver
Telescoping magnet
Fender cover
High-temperature anti-seizelubricant
Electronic spray
![Page 3: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/3.jpg)
AUTODOC recommends:
CARRY OUT REPLACEMENT IN THE FOLLOWING ORDER:
1
Open the hood.
WWW.AUTODOC.CO.UK 3–28
The replacement procedure is the same for all spark plugs.
All work should be done with the engine stopped.
![Page 4: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/4.jpg)
2
Use a fender protection cover to prevent damaging paintwork and plastic parts of the car.
3
Disconnect the crankcase ventilation hose from the air duct. Use round-nose pliers.
WWW.AUTODOC.CO.UK 4–28
![Page 5: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/5.jpg)
4
Unscrew the clamps and fasteners on the air filter intake pipe. Use a drive socket #10. Use a
ratchet wrench.
5
Disconnect the air intake pipe from the air filter housing.
WWW.AUTODOC.CO.UK 5–28
![Page 6: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/6.jpg)
6
Unscrew the fasteners connecting the throttle valve to the intake manifold. Use a drive socket
#8. Use a ratchet wrench.
7
Release the clamp and detach the connector and the vacuum hose from the intake manifold
near the throttle valve. Use round-nose pliers.
WWW.AUTODOC.CO.UK 6–28
![Page 7: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/7.jpg)
8
Unscrew the fasteners of the intake manifold bracket. Use a drive socket #10.
9
Detach the vacuum booster hose from the intake manifold.
WWW.AUTODOC.CO.UK 7–28
![Page 8: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/8.jpg)
10
Unscrew the intake manifold fasteners. Use a drive socket #10. Use a ratchet wrench.
11
Remove the intake manifold.
WWW.AUTODOC.CO.UK 8–28
![Page 9: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/9.jpg)
12
Cover the intake manifold passages with a microfibre towel to prevent dust and dirt from
getting inside.
13
Unscrew the ignition coil bracket. Use a drive socket #10.
WWW.AUTODOC.CO.UK 9–28
![Page 10: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/10.jpg)
14
Take out the ignition coil from the spark plug well.
15
Clean dirt, dust and debris from inside the spark plug well.
WWW.AUTODOC.CO.UK 10–28
![Page 11: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/11.jpg)
16
Unscrew the spark plugs. Use the spark plug socket #16. Use a ratchet wrench.
17
Take out the spark plugs. Use a telescoping magnet.
WWW.AUTODOC.CO.UK 11–28
![Page 12: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/12.jpg)
18
Apply a thin layer of a special high temperature anti-seize lubricant to the threads of the new
spark plugs. Treat the surface of the terminals of the new spark plugs. Use electronic spray.
19
Install the new spark plugs into their mounting seats.
WWW.AUTODOC.CO.UK 12–28
![Page 13: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/13.jpg)
20
Screw new spark plugs and tighten them. Use the spark plug socket #16. Use a torque
wrench. Tighten it to 25 nm torque.
AUTODOC recommends:
WWW.AUTODOC.CO.UK 13–28
Don't tighten the plugs with excessive force. Exceeding tighteningtorque can damage the thread connection.
Be careful when working with a spark plug wrench. Its skewing cancause damage to the threaded connection.
![Page 14: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/14.jpg)
21
Install the ignition coil to the spark plug well. Make sure you hear a click indicating that it is
locked in place.
AUTODOC recommends:
22
Tighten the ignition coil fastening. Use a drive socket #10. Use a torque wrench. Tighten it to
9 nm torque.
WWW.AUTODOC.CO.UK 14–28
Follow the installation sequence.
![Page 15: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/15.jpg)
23
Remove the microfibre towel from the intake manifold.
24
Remove the intake manifold gasket. Use a flat screwdriver.
WWW.AUTODOC.CO.UK 15–28
![Page 16: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/16.jpg)
25
Install the new intake manifold gasket.
26
Install the intake manifold.
WWW.AUTODOC.CO.UK 16–28
![Page 17: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/17.jpg)
27
Tighten the intake manifold fasteners. Use a drive socket #10. Use a torque wrench. Tighten it
to 15 nm torque.
28
Tighten the fasteners of the intake manifold bracket. Use a drive socket №10. Use a torque
wrench. Tighten it to 15 nm torque.
WWW.AUTODOC.CO.UK 17–28
![Page 18: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/18.jpg)
29
Attach the vacuum booster hose to the intake manifold.
30
Squeeze and install the vacuum booster hose clamp. Use round-nose pliers.
WWW.AUTODOC.CO.UK 18–28
![Page 19: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/19.jpg)
31
Install the throttle valve on the intake manifold.
32
Tighten the throttle valve fasteners. Use a drive socket #8. Use a torque wrench. Tighten it to
16 nm torque.
WWW.AUTODOC.CO.UK 19–28
![Page 20: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/20.jpg)
33
Attach the connector and the vacuum hose to the intake manifold near the throttle valve. Use
round-nose pliers.
34
Connect the air intake pipe to the air filter housing.
WWW.AUTODOC.CO.UK 20–28
![Page 21: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/21.jpg)
35
Connect the crankcase ventilation hose to the air duct. Use round-nose pliers.
36
Tighten the clamp and fasteners on the air filter intake pipe. Use a drive socket #10. Use a
ratchet wrench.
WWW.AUTODOC.CO.UK 21–28
![Page 22: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/22.jpg)
37
Run the engine for a few minutes. This is necessary in order to make sure that the component
operates properly.
38
Shut off the engine.
39
Remove the fender protection cover.
WWW.AUTODOC.CO.UK 22–28
![Page 24: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/24.jpg)
DID YOU FIND THESE INSTRUCTIONSHELPFUL?
YES NO
BECOME A MEMBER OF AUTODOC CLUB!
WWW.AUTODOC.CO.UK 24–28
![Page 25: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/25.jpg)
AUTODOC — TOP QUALITY AND AFFORDABLE CARPARTS ONLINE
AUTODOC MOBILE APP: GREAT DEALS AND CONVENIENTSHOPPING
A GREAT SELECTION OF SPARE PARTS FOR YOUR CAR
WWW.AUTODOC.CO.UK 25–28
![Page 26: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/26.jpg)
BUY SPARE PARTS FOR NISSAN
SPARK PLUGS: A WIDE SELECTION
WWW.AUTODOC.CO.UK 26–28
![Page 27: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/27.jpg)
CHOOSE CAR PARTS FOR NISSAN QASHQAI I (J10)
SPARK PLUGS FOR NISSAN: BUY NOW
WWW.AUTODOC.CO.UK 27–28
![Page 28: How to replace spark plugs on NISSAN QASHQAI I J10](https://reader033.fdocuments.us/reader033/viewer/2022053120/62922df2689b295b1e018057/html5/thumbnails/28.jpg)
SPARK PLUGS FOR NISSAN QASHQAI I (J10): THE BEST DEALS &OFFERS
The document contains only general recommendations that may be useful for you when you perform repair or replacement work. AutoDocshall not be liable for any loss, injury, damage of property occurring in the repair or replacement process due to incorrect use ormisinterpretation of the provided information.
AutoDoc shall not be liable for any possible mistakes and uncertainties in this guide. The information provided is for information purposesonly and cannot replace advice from specialists.
AutoDoc shall not be liable for incorrect or hazardous usage of equipment, tools and car parts. AutoDoc strongly recommends to be carefuland observe the safety rules when performing repair or replacement works. Remember: usage of low quality auto parts does not guaranteeyou the appropriate level of road safety.
© Copyright 2018 – All the contents of this website, in particular texts, photographs and graphics, are protected by copyright. All rights,including reproduction, publication, editing and translation rights, are reserved by Autodoc GmbH.
WWW.AUTODOC.CO.UK 28–28
Disclaimer: